LG | L1811S | LG L1811S Owner’s Manual

This unit has been
engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On
Use
Safety
only the power cord supplied
with the unit. In
case
you
use
another power
by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
cord, make
that it is certified
sure
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
or listed on the display. If you are not sure what type of power supply
this manual
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
cords and broken
technician for
plugs. They may
replacement.
Do not
the
Open
result in
are
a
dangerous. So
shock
or
are frayed power
fire hazard. Call your service
Display.
There
are no user
There
are
serviceable components inside.
Dangerous High Voltages inside, even when the power
Contact your dealer if the display is not operating properly.
is OFF.
To Avoid Personal
Injury :
place the display on a sloping shelf unless properly secured.
only a stand recommended by the manufacturer.
Do not
Use
To Prevent Fire
or
Hazards:
display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Always
turn the
On Installation
Do not allow
the
anything to rest upon or roll over the power cord,
display where the power cord is subject to damage.
Do not
this
use
display
sink, laundry tub, in
near
a wet
water such as near a
basement,
Displays are provided with ventilation
generated during operation. If
of heat
and do not
place
bathtub, washbowl, kitchen
swimming pool.
openings in the cabinet to allow the release
these openings are blocked, built-up heat
or near a
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
can cause
Cover the
Place the
Do not rub
mar, or
openings with cloth or other material.
display near or over a radiator or heat source.
or
strike the Active Matrix LCD with
damage
the Active Matrix LCD
Do not press the LCD
some
screen
with your
anything
permanently.
finger for a long
hard
time
as
as
this may scratch,
this may
cause
afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If
possible,
use
the recommended resolution to obtain the best
image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD
On
panel.
Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on
screen because over-spraying may cause electrical shock.
On
the
display
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
the
Connecting
Display
Using the Computer
1. Connect the signal cable. When attached, tighten the thumbscrews to secure
the connection.
2. Connect the power cord into a proper power outlet that is easily accessible and
close to the
display.
NOTE
This is
This
a
rear
simplified representation of the rear view.
view represents a general model; your display
may differ from the view
as
shown.
Signal Cable
Power Cord
Analog signal
D-sub*
Wall-outlet
*
type*
PC-outlet
Varies according to model.
type*
PC
MAC
Mac adapter
For Apple Macintosh use,
a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
A3
Control Panel Functions
Front Panel Controls
Control
Function
Power Button
Use this button to turn the
Power
This Indicator
(DPMS)
lights
display
on or
up green when the
off.
display
Indicator
operates normally. If the display is in DPM (Energy
Saving) mode, this indicator color changes to amber.
MENU Button
Use this button to enter
or
exit the On Screen
Display.
Buttons
Use these buttons to choose
the On Screen
SELECT Button
Use this button to enter
Display.
A4
or
adjust
items in
Display.
a
selection in the On Screen
Control Panel Functions
Control
Direct Access Function
100
100
Bring
up Contrast and
AUTO
Brightness adjustment.
adjustment
function
When
PROCESSING
AUTO CONFIGURATION
adjusting your display settings, always press the AUTO
entering the On Screen Display(OSD). This will
automatically adjust your display image to the ideal settings for
the current screen resolution size (display mode).
button before
The best
display
mode is 1280x1024.
CONTROLS LOCKED/UNLOCKED
:
MENU and
CONTROLS LOCKED
This function allows you to secure the current control settings,
so that they cannot be inadvertently changed. Press and hold
CONTROLS UNLOCKED
the MENU button and
button for 3 seconds: the message
"CONTROLS LOCKED" appears.
You
can
unlock the OSD controls at any time
button for 3 seconds:
by pushing
MENU button and
the message "CONTROLS UNLOCKED" will appear.
A5
the
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the
To make
display to stabilize
adjustments
for at least 30 minutes before
in the On Screen
MENU
Display,
SELECT
Press the MENU Button, then the main
access a
becomes
control,
use
highlighted,
Use the
Accept
follow these steps:
SELECT
MENU
To
making image adjustments.
the
the
of the OSD appears.
Buttons. When the icon you want
or
press the SELECT Button.
Buttons to
changes by pressing
Exit the OSD
menu
by Pressing
adjust
the item to the desired level.
the SELECT Button.
the MENU Button.
A6
On Screen
The
and
Display(OSD) Selection
and
Adjustment
following table indicates all the On Screen Display control, adjustment,
setting menus.
Main
menu
BRIGHTNESS
CONTRAST
COLOR
Sub
Reference
menu
BRIGHTNESS
To
CONTRAST
PRESET
adjust the brightness
contrast of the
9300K
and
screen
To customize the color of the
6500K
screen
R/G/B(User Color)
GAMMA
POSITION
TRACKING
SETUP
V POSITION
To
H POSITION
screen
CLOCK
To
adjust the position
PHASE
improve the clarity and
stability of the screen
LANGUAGE*
To customize the
IMAGE SIZE*
for
a
user's
FACTORY RESET*
:
Adjustable
NOTE
The order of icons may differ
This function is available for
depending
on
designated
A7
the model
models
only.
screen
operating
OSD POSITION*
*
of the
(A7~A9).
status
environment
On Screen
You
were
Display(OSD) Selection
introduced to the
and
Adjustment
procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
To
adjust the brightness and
OSD
contrast of the
Adjust
screen
Description
BRIGHTNESS / CONTRAST
BRIGHTNESS
To
88
adjust
the
brightness
of the
screen.
100
CONTRAST
To
To customize the color of the
OSD
9300K
the contrast of the
screen.
screen
Adjust
Description
PRESET
COLOR
PRESET
adjust
9300K/6500K
Select the
6500K
RED
GREEN
?
9300K:
?
6500K:
color.
screen
Slightly
Slightly
bluish white.
reddish white.
BLUE
RED
GAMMA
GREEN
Set your
own
color levels.
BLUE
GAMMA
Set your own gamma value. (-50~50)
On the monitor, high gamma values
display
values
To
adjust the position of the
OSD
whitish images and low gamma
display high contrast images.
screen
Adjust
Description
POSITION
Vertical Position
To
61
39
move
image
up and down.
Horizontal Position
To
A8
move
image
left and
right.
On Screen
To
Display(OSD) Selection
improve
OSD
the
clarity
and
and
Adjustment
of the
stability
Adjust
screen
Description
To minimize any vertical bars
stripes visible on the screen
CLOCK
TRACKING
background.The horizontal
change.
CLOCK
or
screen
size will also
PHASE
To
PHASE
adjust
the focus of the
display.
This item allows you to remove any
horizontal noise and clear or sharpen
the
To customize the
OSD
screen
status for
a
image
user's
Adjust
operating environment
Description
LANGUAGE*
SETUP
LANGUAGE
ENGLISH
IMAGE SIZE
FULL
OSD POSITION
FACTORY RESET
of characters.
To choose the
control
IMAGE SIZE*
size
fit in the full
1024x768@60Hz
the
This function
original
NO
language in which
displayed.
names are
displays the image in its
enlarged size so as to
screen of the LCD panel.
or
PRESET MODE
OSD POSITION* To
on
adjust position
the
of the OSD window
screen.
FACTORY
Return to all
RESET*
except "LANGUAGE".
factory
default
settings
If you don't want to reset the monitor,
the
button to select NO and
use
then press the SELECT button.
NOTE
*
This function is available for
designated
A9
models
only.
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
Check and
see
if the power cord is connected
display connected?
properly
Is the power indicator
light on?
Press the Power button.
Is the power on and the
power indicator green?
Adjust the brightness
Is the power indicator
amber?
If the
the
to
display
mouse or
bring
Make
Try
to the power outlet.
and the contrast.
is in power
pressing
saving mode, try moving
key on the keyboard
any
up the screen.
if the power is
sure
to turn
on
on.
the PC.
Do you see an "INPUT
SIGNAL OUT OF
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
RANGE" message
the screen?
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
on
SIGNAL
Doyouseea"NO
"message on
This message appears when the signal cable
between your PC and your display is not
the screen?
connected. Check the
Do you
see a
"CONTROLS LOCKED" message
Do you see
"CONTROLS LOCKED"
when you
button?
signal
push
MENU
You
cable and
on
try again.
the screen?
the current control
settings,
they
inadvertently
changed. You can unlock the OSD controls
at any time by pushing the MENU button
so
can secure
that
and
cannot be
button for 3 seconds: the message
"CONTROLS UNLOCKED" will appear.
A10
Troubleshooting
Display image
Display
is incorrect
Position is
incorrect.
Press the AUTO button to
automatically adjust
image to the ideal setting.
are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
your display
If the results
recommend resolution.
On the
screen
vertical
background,
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
The
screen
mono or
color is
abnormal.
Press the AUTO button to
automatically adjust
image to the ideal setting.
are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
your display
If the results
Press the AUTO button to
automatically adjust
image to the ideal setting.
are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
your display
If the results
Check if the
and
signal
cable is
properly connected
screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
use a
the slot.
Set the color
color)
The
screen
blinks.
setting higher than 24 bits (true
Settings.
at Control Panel
Check if the
screen
-
is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be
A11
higher than AC100-240V 50/60Hz.
Troubleshooting
Have you installed the
Have you installed the
display driver?
driver?
display
Be
sure
display
to install the
driver CD
display driver from the
(or diskette) that comes with
your display. Or, you can also download the
driver from our web site: http://www.lge.com.
Do you
see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
Make
sure
Plug&Play
monitor found"
message?
A12
to check if the video card
function.
supports
Specifications
Display
Flat Panel Active matrix-TFT LCD
18.1 inches
Anti-Glare
(45.97cm)
coating
18.1 inches viewable
0.28
Sync Input
Video
Input
Resolution
mm
pixel pitch
Horizontal
Freq.
Vertical Freq.
Input Form
30
83kHz
(Automatic)
(Automatic)
Separate TTL, Positive/Negative
Composite TTL Positive/Negative
-
56
75Hz
-
SOG (Sync On Green)
15 pin D-Sub Connector
Signal Input
Input Form
RGB
Analog (0.7Vp-p/75ohm)
Max
VESA 1280
x
Recommend
VESA 1280
x
1024@75Hz
1024@60Hz
Plug&Play
DDC 2B
Power
Normal
:
Consumption
Stand-by/Suspend
≤
DPMS Off
≤3W
Dimensions
Width
40.6
cm
/ 15.98 inches
&Weight
(with tilt stand)
Height
Depth
43.1
cm
/ 16.97 inches
22.3
cm
/ 8.78 inches
Net
7.8
Tilt
-5˚~30˚
Swivel
360˚
Tilt
Range
Power
Input
Environmental
Conditions
Tilt Stand
Signal
cable
53W
3W
kg (17.19 lbs)
AC 100-240V 50/60Hz 1.0A
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Conditions
Storage
Temperature -20˚C to 60 ˚C
5 % to 95 % non-Condensing
Humidity
Attached( O ),
Detached
(
Attached(
Detached
(O)
),
Power cord
Wall-outlet type
Regulations
TCO99
or
)
PC-outlet type
NOTE
Information in this document is
subject
to
change without
A13
notice.
Specifications
Preset Modes
(Resolution)
Display Modes (Resolution)
1
VGA
2
VGA
720
3
VGA
640
4
VESA
5
Horizontal
Freq. (kHz)
Vertical
Freq. (Hz)
350
31.469
x
400
31.468
70
x
480
31.469
60
640
x
480
37.500
75
VESA
800
x
600
37.879
60
6
VESA
800
x
600
46.875
75
7
MAC
832
x
624
49.725
75
8
VESA
1024
x
768
48.363
60
9
VESA
1024
x
768
60.123
75
75
640
x
70
10
MAC
1152
x
870
68.681
11
VESA
1152
x
900
61.805
65
12
VESA
1280
x
1024
63.981
60
13
VESA
1280
x
1024
79.976
75
VESA wall
mounting
Connected to another
object (stand
type and wall-mounted type. This
monitor accepts a VESA-compliant
mounting
interface
pad.)
Kensington Security Slot- optional
a locking
cable that can be purchased
separately at most computer
Connected to
stores
A14
Download PDF

advertising