LG L1910S User's Guide

User's Guide
L1910S
Make
sure
to read the
Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached
dealer when you
on
the back
require service.
cover
and quote this information to your
This unit has been
engineered and manufactured to ensure your personal
safety,
improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
however
On
Use
Safety
power cord supplied with the unit. In case you use another power
that it is certified by the applicable national standards if not being
only the
cord, make
sure
provided by the supplier. If the
manufacturer
or
power cable is faulty in any way, please contact the
the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate
the
this manual
display only from a power source indicated in the specifications of
listed on the display. If you are not sure what type of power supply
or
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
cords and broken
plugs. They
technician for replacement.
Do not
Open
the
may result in
are
a
dangerous. So are frayed
shock
or
power
fire hazard. Call your service
Display.
There
are no user
There
are
serviceable components inside.
Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
To Avoid Personal
Injury :
place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not
To Prevent Fire
or
Hazards:
display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Always
turn the
On Installation
Do not allow
to rest upon or roll over the power
the
power cord is
anything
display where the
Do not
use
this
display
sink, laundry tub, in
near water
cord, and do
not
place
subject to damage.
such
basement,
as near a
bathtub, washbowl, kitchen
swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
a wet
or near a
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
can cause
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
or strike the Active Matrix LCD with anything hard
damage the Active Matrix LCD permanently.
Do not rub
mar, or
Do not press the LCD
some
screen
with your
finger for a long
time
as
as
this may scratch,
this may
cause
afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If
possible,
use
the recommended resolution to obtain the best
image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD
On
panel.
Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly
screen because over-spraying may cause electrical shock.
On
on
the
display
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
Connecting
the
Display
Using the Computer
1. Connect the signal cable. When attached, tighten the thumbscrews to secure
the connection.
2. Connect the power cord into a proper power outlet that is easily accessible and
close to the
display.
NOTE
This is
This
a
rear
simplified representation of the rear view.
view represents a general model; your display may differ from the view as shown.
Power Cord
Signal Cable
Analog signal
D-sub*
*
Varies according to model.
Wall-outlet
type*
2
1
Mac adapter
PC-outlet
For Apple Macintosh use,
type*
a
separate plug adapter is
needed to change the 15 pin
high density (3 row) D-sub
VGA connector on
thesupplied cable to a
PC
15 pin
2 row connector.
MAC
3.
Press
button
on
the front switch
panel
to turn the
When monitor power is turned on, the 'Self
power
Image Setting Function' is executed automatically.
on.
NOTE
'
Self
Image Setting
Function'? This function
connects the monitor for the first
provides the
user
with
optimal display settings.When the
user
time, this function automatically adjusts the display to optimal settings for
individual input signals. If you want to adjust the monitor while in use, or wish to manually run this function once
again, push the 'AUTO' button on the front panel of the monitor. Otherwise, you may execute the Factory reset'
option on the OSD adjustment menu. However, be aware that this option initializes all the menu items except
'Language'.
'
A3
Connecting
the
Display
Positioning your display
Adjust the position of the panel
Tilt
:
in various ways for maximum comfort.
-5˚~30˚
-5˚
Swivel
:
30˚
360˚
360˚
A4
Control Panel Functions
Front Panel Controls
Control
Function
Power Button
Use this button to turn the
Power
This Indicator
(DPMS)
lights
display
on or
up green when the
off.
display
Indicator
operates normally. If the display is in DPM (Energy
Saving) mode, this indicator color changes to amber.
MENU Button
Use this button to enter
or
exit the On Screen
Display.
Buttons
Use these buttons to choose
the On Screen
AUTO/SELECT
Button
Use this button to enter
Display.
AA5
or
adjust
items in
Display.
a
selection in the On Screen
Control Panel Functions
Control
Direct Access Function
100
up Contrast and
Bring
100
Brightness adjustment.
AUTO IMAGE ADJUSTMENT
When
adjusting your display settings, always press the
AUTO/SELECT button before entering the On Screen
Display(OSD). This will automatically adjust your display image
settings for the current screen resolution size
(display mode).
to the ideal
The best
display
mode is 1280x1024.
This feature lets you easily select the best desired image
condition optimized to the environment (ambient illumination,
image types etc.).
?
DAY
?
NIGHT
:
?
TEXT
For text
?
?
?
:
Bright
ambient illumination
Dark ambient illumination
images (Word processing etc.)
images in videos or movies
PHOTO : For pictures or drawings
USER MODE : For use under user setup image
conditions (Brightness, contrast and color tint are
selected by the user in OSD Screen Setup Menu.)
:
MOVIE
:
For animation
CONTROLS LOCKED/UNLOCKED
:
MENU and
This function allows you to secure the current control settings,
so that they cannot be inadvertently changed. Press and hold
the MENU button and
button for 3 seconds: the message
"CONTROLS LOCKED" appears.
You
can
unlock the OSD controls at any time
button for 3 seconds:
by pushing
MENU button and
the message "CONTROLS UNLOCKED" will appear.
A6
the
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the
To make
display to
stabilize for at least 30 minutes before
adjustments
in the On Screen
Display, follow these steps:
Press the MENU Button, then the main
To
access a
becomes
control,
use
highlighted,
Use the
the
making image adjustments.
menu
of the OSD appears.
Buttons. When the icon you want
or
press the AUTO/ SELECT Button.
Buttons to
adjust the item
to the desired level.
Accept the changes by pressing the AUTO/ SELECT Button.
Exit the OSD
by Pressing the MENU Button.
A7
On Screen
The
and
Display(OSD)
Selection and
Adjustment
following table indicates all the On Screen Display control, adjustment,
setting menus.
Main
menu
BRIGHTNESS
CONTRAST
COLOR
Sub
Reference
menu
BRIGHTNESS
To
CONTRAST
PRESET
adjust the brightness
and
contrast of the screen
9300K
To customize the color of the
6500K
screen
R/G/B(User Color)
GAMMA
POSITION
TRACKING
SETUP
V POSITION
To
H POSITION
screen
CLOCK
To
adjust the position
PHASE
improve the clarity
stability of the screen
LANGUAGE
To customize the
for
OSD POSITION
a
user's
WHITE BALANCE
Adjustable
NOTE
The order of icons may differ
depending
on
A8
and
screen
operating
FACTORY RESET
:
of the
the model (A8~A10).
status
environment
On Screen
You
were
Display(OSD)
introduced to the
Selection and
Adjustment
procedure of selecting and adjusting an item
the OSD
using
descriptions
system. Listed below are the icons, icon names, and icon
of the all items shown on the Menu.
NOTE
OSD (On Screen
To
Display)
menu
languages
adjust the brightness and
OSD
on
the monitor may differ from the manual.
contrast of the
Adjust
screen
Description
BRIGHTNESS / CONTRAST
BRIGHTNESS
To
88
adjust
the
brightness
of the
screen.
100
CONTRAST
To
To customize the color of the
OSD
9300K
the contrast of the
screen.
screen
Adjust
Description
PRESET
COLOR
PRESET
adjust
9300K/6500K
Select the screen color.
9300K: Slightly bluish white.
6500K
?
RED
?
GREEN
6500K:
Slightly
reddish white.
BLUE
RED
GAMMA
GREEN
Set your
own
color levels.
BLUE
GAMMA
To
adjust the position of the
OSD
Set your own gamma value. (-30~30)
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
screen
Adjust
Description
POSITION
Vertical Position
61
To
move
image
up and down.
39
Horizontal Position
To
A9
move
image left
and
right.
On Screen
To
Display(OSD) Selection
improve
OSD
the
clarity
and
and
Adjustment
of the
stability
Adjust
screen
Description
CLOCK
TRACKING
To minimize any vertical bars
stripes visible on the screen
background.The horizontal
change.
CLOCK
or
screen
size will also
PHASE
PHASE
To
adjust
the focus of the
display.
This item allows you to remove any
horizontal noise and clear or sharpen
the
To customize the
OSD
screen
status for
a
image
user's
Adjust
operating environment
Description
LANGUAGE
SETUP
LANGUAGE
of characters.
To choose the
control
ENGLISH
language in which
displayed.
the
names are
OSD POSITION
FACTORY RESET
NO
OSD POSITION
To
adjust position
on
the
of the OSD window
screen.
1280x1024@60Hz
PRESET MODE
FACTORY
RESET
Return to all
factory
default
settings
except "LANGUAGE".
If you don't want to reset the monitor,
the
button to select NO and
use
then press the AUTO/SELECT button.
WHITE
If the
BALANCE
the
output of the video card is different
required specifications,
the color
level may deteriorate due to video
signal distortion. Using this function, the
signal
level is
standard
adjusted
to fit into the
output level of the video card
in order to
provide
the
optimal image.
Activate this function when white and
black colors
For
If this does not
are
present in the
screen.
example
improve the screen image, restore the factory default settings. If
necessary, perform the white balance function again. This function will be enabled
only when the input signal is an analog signal.
A10
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
display connected?
Check and
Is the power indicator
light on?
Press the Power button.
Is the power on and the
power indicator green?
Adjust the brightness
Is the power indicator
amber?
properly
If the
the
to
see
if the power cord is connected
to the power outlet.
and the contrast.
is in power saving mode, try moving
pressing any key on the keyboard
display
mouse or
bring up the screen.
Make
sure
Try to turn
if the power is
the PC.
on.
on
Do you see an "INPUT
SIGNAL OUT OF
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
RANGE" message
the screen?
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
on
SIGNAL
Doyouseea"NO
"message on
This message appears when the signal cable
between your PC and your display is not
the screen?
connected. Check the
Do you
see a
"CONTROLS LOCKED" message
Do you see
"CONTROLS LOCKED"
when you
button?
signal cable
push
MENU
You
on
and try
again.
the screen?
the current control
settings,
they
inadvertently
changed. You can unlock the OSD controls
at any time by pushing the MENU button
so
can secure
that
and
cannot be
button for 3 seconds: the message
"CONTROLS UNLOCKED" will appear.
A11
Troubleshooting
Display image
Display
is incorrect
Position is
incorrect.
Press the AUTO/SELECT button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
Check Control Panel --> Display --> Settings and
see if the frequency or the resolution were changed.
If yes, readjust the video card to the recommend
resolution.
On the
screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
The
screen
mono or
color is
abnormal.
Press the AUTO/SELECT button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in the
on screen display.
Press the AUTO/SELECT button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings and
adjust the display to the recommended resolution or
adjust the display image to the ideal setting. Set the
color setting higher than 24 bits (true color).
Check if the signal cable is
properly connected and
screwdriver to fasten if necessary.
Make sure the video card is properly inserted in the
use a
slot.
Set the color setting
at Control Panel
The
screen
blinks.
-
higher than 24 bits (true color)
Settings.
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It has
to be
higher than AC100-240V 50/60Hz.
A12
Troubleshooting
Have you installed the
Have you installed the
display driver?
Do you
see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
display
driver?
Be sure to install the display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
driver from our web site: http://www.lge.com.
Make
sure
to check if the video card
Plug&Play function.
monitor found"
message?
A13
supports
Specifications
Display
19 inches (48.26cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
19 inches viewable
0.294
Sync Input
Video
Input
Resolution
Plug&Play
mm
pixel pitch
Horizontal
Freq.
Vertical Freq.
Input Form
30
56
-
-
83kHz (Automatic)
75Hz (Automatic)
Separate TTL, Positive/Negative
Composite TTL Positive/Negative
SOG (Sync On Green)
15 pin D-Sub Connector
Signal Input
Input Form
RGB Analog (0.7Vp-p/75ohm)
Max
VESA 1280
x
1024@75Hz
Recommend
VESA 1280
x
1024@60Hz
DDC 2B
45W
Power
Normal
:
Consumption
Stand-by/Suspend
≤
DPMS Off
≤1W
Width
41.28
cm
Height
Depth
43.50
cm
22.3
cm
Net
7.28
kg
Tilt
-5˚~30˚
Swivel
360˚
Dimensions
&Weight
(with tilt stand)
Tilt
Range
Power
Input
Environmental
Conditions
Tilt Stand
Signal
cable
Power cord
1W
/ 16.25 inches
/ 17.13 inches
/ 8.78 inches
AC 100-240V~50/60Hz 1.0A
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Conditions
Storage
Temperature -20˚C to 60 ˚C
5 % to 95 % non-Condensing
Humidity
Attached( O ), Detached (
Attached(
)
), Detached ( O )
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A14
notice.
Specifications
Preset Modes
(Resolution)
Display Modes (Resolution)
Horizontal
Freq. (kHz)
Vertical
Freq. (Hz)
VGA
640
x
350
31.469
70
VGA
720
x
400
31.468
70
VGA
640
x
480
31.469
60
VESA
640
x
480
37.500
75
VESA
800
x
600
37.879
60
VESA
800
x
600
46.875
75
MAC
832
x
624
49.725
75
VESA
1024
x
768
48.363
60
VESA
1024
x
768
60.123
75
10
MAC
1152
x
870
68.681
75
11
VESA
1152
x
900
61.805
65
12
VESA
1280
x
1024
63.981
60
13
VESA
1280
x
1024
79.976
75
123456789
Indicator
MODE
LED Color
Normal
green
Stand-by/Suspend
amber
DPMS Off
amber
A15
Specifications
VESA wall
mounting
Connected to another
object (stand type
and wall-
mounted type. This monitor accepts a VESAcompliant mounting interface pad.- optional)
For further
Mounting
information, refer
to the VESA Wall
Instruction Guide.
Kensington Security Slot- optional
a locking
cable that can be purchased
separately at most
Connected to
computer
stores
A16
Digitally yours