LG | M4210C-BA | LG M4210C-BAF Owner’s Manual

User’s Guide
M4210C
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your dealer when you ask
for service.
Safety Precautions
Please read these safety precautions carefully before using the product.
Warning If you ignore the warning message, you may be seriously injured or there is a possibility of
accident or death.
Caution If you ignore the caution message, you may be slightly injured or the product may be damaged
Precautions in installing the Product
Warning
Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.
Keep the packing anti-moisture material or vinyl packing out of the reach of children.
- Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the
nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.
Do not put heavy objects on the product or sit upon it.
- If the product collapses or is dropped, you may be injured. Children must pay particular attention.
Do not leave the power or signal cable unattended on the pathway.
- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.
Install the product in a neat and dry place.
- Dust or moisture can cause electrical shock, fire or product damage.
If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the
service center.
- If you continue to use without taking proper measures, electrical shock or fire can occur.
If you dropped the product or the case is broken, turn off the product and unplug the power cord.
- If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service
center.
Do not drop an object on or apply impact to the product. Do not throw any toys or objects on the product
screen.
- It can cause injury to human, problem to product and damage the display.
Caution
Make sure the product ventilation hole is not blocked. Install the product in a suitably wide place (more
than 10cm from the wall)
- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat.
Do not block the ventilation hole of the product by a tablecloth or curtain.
- The product can be deformed or fire can break out due to overheating inside the product.
Install the product on a flat and stable place that has no risk of dropping the product.
- If the product is dropped, you may be injured or the product may be broken.
Install the product where no EMI occurs.
Keep the product away from direct sunlight.
- The product can be damaged.
1
Safety Precautions
Electrical Power Related Precautions
Warning
Make sure to connect the power cable to the grounded current.
- You may be electrocuted or injured.
Use the rated voltage only.
- The product can be damaged, or you may be electrocuted.
In the presence of thunder and lightning, never touch the power cord and signal cable because it can be
very dangerous.
- It can cause electric shock.
Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet.
Use a power bar with a grounding terminal designed for exclusive use with the computer.
- A fire can break out due to overheating.
Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry
the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
If you don’t intend to use the product for a long time, unplug the power cable from the product.
- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.
Fix the power cable completely.
- If the power cable is not fixed completely, a fire can break out.
Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or put
heavy objects on the power cord.
- The power line can be damaged, which may cause electric shock or fire.
Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end is
connected to the input terminal on the wall. Additionally, do not touch the power cable right after
plugging into the wall input terminal.
- You may be electrocuted.
The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily
accessible after installation.
Main power breaker is the power cord and this breaking device must be located at a location where it is easy
to operate.
Caution
Do not unplug the power cord while the product is in use.
- Electrical shock can damage the product.
Precautions in Moving the Product
Warning
Make sure to turn off the product.
- You may be electrocuted or the product can be damaged.
Make sure to remove all cables before moving the product.
- You may be electrocuted or the product can be damaged.
2
Safety Precautions
Caution
Do not shock the product when moving it.
- You may be electrocuted or the product can be damaged.
Do not dispose the product-packing box. Use it when you move.
Make the panel face forward and hold it with both hands to move.
- If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center
for repair.
Precautions in Using the Product
Warning
Do not disassemble, repair or modify the product at your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check, calibration or repair.
When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent
scratching. Do not clean with a wet cloth.
Keep the product away from water.
- Fire or electric shock accident can occur.
Caution
Do not put or store inflammable substances near the product.
- There is a danger of explosion or fire due to careless handling of the inflammable substances.
When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent
scratching. Do not clean with a wet cloth.
- The water can sink into the product, which can cause electric shock or serious malfunction.
Take a rest from time to time to protect your vision.
Keep the product clean at all times.
Take a comfortable and natural position when working with a product to relax the muscles.
Take a regular break when working with a product for a long time.
Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make
a scratch on it.
Keep the proper distance from the product.
- Your vision may be impaired if you look at the product too closely.
Set the appropriate resolution and clock by referring to the User’s Guide.
- Your vision can be impaired.
Use authorized detergent only when cleaning the product. (Do not use benzene, thinner or alcohol.)
- Product can be deformed.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of your local authority.
3
Using the Remote Control
Name of the Remote Control Buttons (A type)
• Power On/Off Button
• Sleep Button
When watching AV/S-Video/RGB/HDMI
• Component1/ Component2
The product will be automatically turned off
after a certain period of time.
Press this button repetitively to select an
appropriate time duration
• Mute button
• AV Button
• Input Select Button
(See next page)
• Menu Button
• Exit Button
• Volume
• PSM Button
- Automatically adjusts the image.
Press this button repetitively to set
the intended screen.
Button
• Check Button
• Up and Down buttons
Bring up and down direction adjustment.
• Auto Button
Automatic adjustment function
(Operational for the analog signal only)
There is not a function
which is supported
• ARC button
To select the image
size of the screen.
• Video Operation Button
Applicable for LG products only
4
Using the Remote Control
• AV Button
• Input Select Button
Each time you press the Input
button it will change to
AV
Component1
Component2
RGB
HDMI/DVI
If you press the button once,
the following Input Signal
Window will appear. Select
the signal type you want
using the
button.
Input
Inserting batteries into remote control.
1. Take out the battery cap.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cap.
• Dispose of used batteries in the recycle bin to prevent
environmental pollution.
5
Using the Remote Control
Name of the Remote Control Buttons( B type)
• Power On/Off Button
• Input Select Button
(See next page)
• AV Button
• Sleep Button
When watching AV/S-Video/RGB/HDMI
/Component1/ Component2
The product will be automatically turned
off after a certain period of time.
Press this button repetitively to
select an appropriate time duration
• PSM Button
- Automatically adjusts the image.
Press this button repetitively to set
the intended screen.
There is not a function
which is supported
1
2
3
4
5
6
7
8
9
• ARC button
To select the image size of the
screen.
• Auto Button
Automatic adjustment function
(Operational for the analog signal only)
There is not a function
which is supported
0
There is not a function
which is supported
• Exit Button
• Menu Button
• UP and Down buttons
Bring up and down direction
adjustment.
• Volume
Button
• Check Button
*
• Mute button
There is not a function
which is supported
6
Using the Remote Control
• AV Button
• Input Select Button
Each time you press the Input
button it will change to
AV
Component1
Component2
RGB
HDMI/DVI
If you press the button once,
the following Input Signal
Window will appear. Select
the signal type you want
using the
button.
1
2
3
4
5
6
7
8
9
Input
0
*
Inserting batteries into remote control.
1. Take out the battery cap.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cap.
• Dispose of used batteries in the recycle bin to prevent
environmental pollution.
7
Connecting the Speakers
* Applicable only for models that support the speakers
Mount the product onto the speaker by using a screw as shown in the following
picture, and then connect the speaker cable.
When the speaker is installed.
8
Name and Function of the Parts
* The product image in the user’s guide could be different from the actual image.
Rear View
REMOTE
CONTROL IN
RS-232C
(CONTROL&
SERVICE)
HDMI/DVI IN
RGB IN
AUDIO
(RGB/DVI)
COMPONENT IN
Y
VIDEO
PB
RS-232C
(CONTROL&
SERVICE)
HDMI/DVI IN
RGB IN
L-AUDIO-R
VIDEO
1
RGB OUT
AV
OUT
2
IN
REMOTE
CONTROL IN
AV IN
L-AUDIO-R
PR
OUT
AUDIO
(RGB/DVI)
S-VIDEO
COMPONENT IN
Y
OUT
VIDEO
PB
AV IN
L-AUDIO-R
PR
L-AUDIO-R
VIDEO
1
RGB OUT
2
IN
AV
OUT
S-VIDEO
Power Connector : Connect the power cord
Wired Remote Control Port
RS-232C Serial Ports
RGB, HDMI/DVI Ports
PC Sound Jack
: Connect the audio cable to the *LINE OUT jack of the PC sound card.
AV Ports
*LINE OUT
A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that
the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of
PC sound card has only Speaker Out, reduce the PC volume.
If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using
the card jumper of the program (Refer to the Sound Card Manual).
9
Connecting to External Devices
When Connecting to your PC
First of all, see if the computer, product and the peripherals are turned off.
Then, connect the signal input cable.
A When connecting with the D-Sub signal input cable.
B When connecting with the HDMI to DVI signal input cable (not included).
A
RGB IN
PC
Rear side of the product.
PC/MAC
MAC
Macintosh Adapter (not included)
Use the standard Macintosh adapter since an incompatible
adapter is available in the market. (Different signaling system)
HDMI/DVI IN
B
(not included)
Rear side of the product.
PC
Connect the Audio cable.
AUDIO
(RGB/DVI)
PC
Rear side of the product.
Connect the power cord.
Rear side of the product.
REMOTE
CONTROL IN
RS-232C
(CONTROL&
SERVICE)
OUT
IN
10
HDMI/DVI IN
RGB IN
RGB OUT
AUDIO
(RGB/DVI)
COMPONENT IN
Y
VIDEO
PB
AV IN
L-AUDIO-R
PR
L-AUDIO-R
VIDEO
1
2
AV
OUT
S-VIDEO
Connecting to External Devices
1 Turn on power by pressing the power button on the product.
SOURCE
AUTO/SET
ON/OFF
Power button
2 Turn on the PC.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
SET
Or, press the SOURCE button on the back of the product.
SOURCE
AUTO/SET
Input
A
When connecting with a D-Sub signal input cable.
• Select RGB : 15-pin D-Sub analog signal.
B
When connecting with a HDMI to DVI signal input cable.
• Select HDMI/DVI : HDMI to DVI Digital signal.
Note
Input
• How to connect to two computers.
Connect the signal cables (HDMI to DVI and D-Sub) to each computer.
Press the INPUT button on the remote control to select the computer to use.
• Directly connect to a grounded power outlet on the wall or a power bar with a ground
wire.
11
Connecting to External Devices
Watching RGB Outputs
Use this function when displaying ANALOG RGB inputs of a PC to the other product.
• To use different products connected to each other
Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT
connector of product 1 and connect the other end to the RGB IN connector of other
products.
15-pin D-Sub Signal Cable
RGB IN
RGB IN
RGB IN
RGB IN
RGB OUT
RGB OUT
RGB OUT
RGB OUT
PC
PC
Product 1
Note
Product 2
Product 3
Product 4
• When multi-connecting in/out cascade format, cables to be less damaged are recommended.
We recommend that you should use cable distributor.
12
Connecting to External Devices
When watching VCR / DVD
Connect the video cable as shown in the below figure and then connect the power
cord (See page 10).
A When connecting with a BNC cable.
B When connecting with a S-Video cable.
• Connect to the S-Video input terminal to
watch high image quality movies.
• Connect the input terminal with a
proper color match.
Product
Product
AV IN
AV IN
L-AUDIO-R
VIDEO
AV
OUT
L-AUDIO-R
VIDEO
S-VIDEO
S-VIDEO
AV
OUT
Audio Cable
(not included)
Audio Cable
(not included)
BNC Cable
(not included)
S-Video Cable
(not included)
VCR/DVD Receiver
VCR/DVD Receiver
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
SET
Input
Or, press the SOURCE button on the back of the product.
SOURCE
AUTO/SET
A
When connecting with an BNC cable.
• Select AV.
B
When connecting with an S-Video cable.
• Select AV.
Note
• When the BNC cable is connected simultaneously with S-Video cable, S-Video cable is first.
13
Connecting to External Devices
When watching HDTV/DVD(480p/576p/720p/1080i/480i/576i)
Connect the video/audio cable as shown in the below figure and then, connect the
power cord (See page 10).
• Connect the input terminal with a proper color match.
A
B
Product
Product
COMPONENT IN
VIDEO
PB
Y
COMPONENT IN
L-AUDIO-R
PR
Y
1
VIDEO
PB
L-AUDIO-R
PR
1
2
2
BNC Cable
(not included)
Audio Cable
(not included)
BNC Cable
(not included)
Audio Cable
(not included)
HDTV Receiver
HDTV Receiver
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
SET
Or, press the SOURCE button on the back of the product.
SOURCE
A
• Select Component 1
B
• Select Component 2
Input
AUTO/SET
14
Input
Connecting to External Devices
When watching HDMI/DVI/RGB from the VCR/DVD/Set-top Box
(480p/576p/720p/1080i)
Connect the video/audio cable as shown in the below figure and then connect the
power cord (See page 10).
HDMI/DVI IN
RGB IN
AUDIO
(RGB/DVI)
HDMI/DVI IN
RGB OUT
HDMI to DVI
Signal Cable
(not included)
Product
Product
Product
A
RGB IN
AUDIO
(RGB/DVI)
B
HDMI/DVI IN
RGB OUT
RCA-PC
Audio Cable
AUDIO
(RGB/DVI)
RGB OUT
D-Sub Signal
Cable
HDMI Signal Cable
(not included)
VCR/DVD/Set-top Box
RGB IN
VCR/DVD/Set-top Box
RCA-PC
Audio Cable
VCR/DVD/Set-top Box
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
SET
Or, press the SOURCE button on the back of the product.
SOURCE
AUTO/SET
Input
A
When connecting with a HDMI to DVI signal input cable.
When connecting with a HDMI signal input cable.
• Select HDMI/DVI
B
When connecting with a D-Sub signal input cable.
• Select RGB
15
Input
Connecting to External Devices
Watching AV Outputs
• When you set the input signal of the main screen as 'AV (CVBS)', you can transmit the signal that
you're watching to the AV output terminal.
Video/TV
BNC Cable
(not included)
Audio Cable
(not included)
AV IN
L-AUDIO-R
VIDEO
Product
S-VIDEO
AV
OUT
BNC Cable
(not included)
Audio Cable
(not included)
Video/TV
Note
• When multi-connecting in/out cascade format, cables to be less damaged are recommended.
We recommend that you should use cable distributor.
16
To arrange cables using cable management
* Applicable only for models that support the stand.
1.
Arrange the cables in the center as shown in the following picture.
OUT
1
RGB OUT
2.
S-VIDEO
AV
OUT
2
IN
Fit the cable management to the Holder Groove downwards.
Y
SERVICE)
OUT
IN
RGB OUT
PB
PR
1
AV
OUT
2
S-VIDEO
cable
management
* When you want remove it.
Hold the Cable management with both
hands and pull it downward.
Warning
• Do not use the cable management as a handle for the Monitor.
• Do not press the cable management.
17
Attaching the product to a wall
* This feature is not available for all models.
• Set it up close to the wall so the product doesn't fall over when it is pushed backwards.
The instructions shown below are a safer way to set up the product, which is to fix it on the wall so the product doesn't
fall over when it is pulled forward. It will prevent the product from falling forward and hurting people. It
will also prevent the product from damage caused by a fall. Please make sure that children don't climb on or hang from the
product.
3
2
1
1. Use the braket and the bolt to fix the product to the wall as shown in the picture.
2. Secure the bracket with the bolt(not provided with product, purchase separately) on the wall.
3. Use a sturdy rope (not provided with the product, purchase separately) to tie the product. It is safer to tie the
rope horizontaliy between the wall and the product.
Note
• When moving the product to anoher place, undo the ropes first.
• Use a product holder or a cabinet that is big and strong enough for the size and weight of the product.
• To use the product safely, make sure that the height of the braket that is mounted on the wall is same as that of the
product.
18
Selecting and Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
SOURCE
SOURCE
Power Button
AUTO/SET
AUTO/SET
ON/OFF
ON/OFF
• Press this button to turn on the power. Press this button again to
turn it off.
Power Indicator
• This Indicator lights up blue when the display operates normally(on
mode). If the display is in sleep (Energy Saving) mode, this indicator
colour changes to amber.
MENU Button
• Use this button to show/hide the OSD (On Screen Display) menu
screen.
OSD Select /
Adjust Button
• Use this button to select an icon or adjust the setting in the OSD screen.
• Adjust the up and down.
• Adjust the volume.
19
Selecting and Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
AUTO/SET Button
[For PC Analog signal]
Auto in progress
For opimal display change
resolution to 1360 X 768
[When XGA Mode is active and
1360 X768 is selected]
SOURCE Button
SOURCE
AUTO/SET
• Select the input signal
AV
Component 1
Component 2
RGB
HDMI/DVI
IR Receiver
Input
Composite Video, Separate Video
HDTV, DVD
HDTV, DVD
15-pin D-Sub analog signal
Digital signal
• The unit that receives the signal from the remote control.
20
Selecting and Adjusting the Screen
OSD Menu
Icon
Function Description
Adjusts screen brightness, contrast and color that you prefer.
PICTURE
Adjusts the audio function.
SOUND
Adjusts the timer function.
TIMER
Adjusts the screen status according to the circumstances.
SPECIAL
Adjusts the screen video.
SCREEN
Note
OSD(On Screen Display)
The OSD function enables you to adjust the screen status conveniently since it provides
graphical presentation.
21
Selecting and Adjusting the Screen
How to adjust the OSD (On Screen Display) screen
(A Type)
Move where
you want to
adjust
Pops up
the menu
screen
Select a
menu icon
Move where
you want to
adjust
Select a
menu icon
Adjust the status
Save
adjustment
Exit from the
menu screen.
(B Type)
• Use the remote control to adjust the OSD screen.
1
Press the MENU Button, then the main menu of the OSD appears.
2
To access a control, use the
3
When the icon you want becomes highlighted, press the SET Button.
4
Use the
5
Accept the changes by pressing the SET Button.
6
Exit the OSD by pressing the EXIT Button.
Buttons.
Buttons to adjust the item to the desired level.
How to adjust the screen automatically
You need to adjust the screen display when connecting the product to
a new computer or changing the mode. Refer to the following section to
set an optimal product screen.
Press the AUTO/SET button (AUTO button in a remote Control) in the
PC analog signal. Then, an optimal screen status will be selected that
fits into the current mode.
If adjustment is not satisfactory, you need to adjust screen position,
clock and phase in the OSD menu.
22
[When XGA Mode is active and
1360 X768 is selected]
Selecting and Adjusting the Screen
Adjusting Screen Color
PSM
CSM
Advanced
Reset
PSM
The PSM function automatically adjusts the screen image quality
depending on the AV usage environment.
• Dynamic : Select this option to display with a sharp image.
• Standard : The most general and natural screen display status.
• Mild : Select this option to display with a mild image.
• User1,2 : Select this option to use the user-defined settings.
User1
Contrast
Brightness
Colour
Sharpness
Tint
100
50
50
50
0
R
G
Contrast : Adjust the difference between the light and dark levels in the picture.
Brightness : To adjust the brightness of the screen.
Colour : To adjust the color to desired level.
Sharpness : To adjust the clearness of the screen.
Tint :To adjust the tint to desired level.
CSM
Selecting a factory setting color set.
• Warm : Slightly reddish white.
• Normal : Slightly bluish white.
• Cool : Slightly purplish white.
• User : Select this option to use the user-defined settings.
Red / Green / Blue
Set your own color levels.
User
Note
Red
0
Green
Blue
0
0
If the 'PSM' setting in the PICTURE menu is set to Dynamic, Standard or Mild the
subsequent menus will be automatically set.
23
Selecting and Adjusting the Screen
Adjusting Screen Color
XD
XD is LG Electronics' unique picture improving technology that displays a real HD source
through an advanced digital signal processing algorithm.
This function is not available in RGB-PC or HDMI/DVI PC modes.
This menu is activated after selecting User1 or User2 of PSM.
PSM
CSM
Auto
Manual
XD Contrast
Advanced
Reset
XD Colour
On
On
XD NR
Off
0
MPEG NR
• Auto : XD is automatically changed to Auto.
• Manual : When selecting the Manual, you can adjust the XD Contrast, XD Colour, XD NR,
MPEG NR.
• XD Contrast : Optimizing the contrast automatically according to the
brightness of the reflection.
• XD Colour : Adjusting the colours of the reflection automatically to
reproduce as closely as possible to natural colours.
• XD NR : Removing the noise up to the point where it does not damage the
original picture.
• MPEG NR : You can select MPEG NR to reduce the picture noise which
may appear on the screen while watching the AV.
Advanced
PSM
CSM
Cinema
Advanced
Reset
Off
Black level
Low
• Cinema : (Function works in the following mode - AV, Component 480i/576i)
When you watch the movie, this function adjusts the set to the best picture
appearance.
• Black Level : (Function works in the following mode - AV(NTSC), HDMI/DVI
adjusts the contrast and the brightness of the screen using the
black level of the screen.
• Low : The reflection of the screen gets brighter.
• High : The reflection of the screen gets darker.
• Auto : Realizing the black level of the screen and set it to High or Low
automatically.
Reset
Return PSM, CSM, XD, Advanced to the default factory settings.
24
Selecting and Adjusting the Screen
Adjusting the audio function
SSM
AVL
Balance
Speaker
SSM
SSM
Surround MAX
AVL
Flat
Balance
Speaker
0
Music
Movie
Sports
User
0
The best sound tone quality will be
selected automatically depending on the
video type that you're currently watching.
• Surround MAX : Set the Surround MAX on. This function plays back the mono or stereo sound input
with the dynamic surround effects. It will provide rich and profound sound tone. If you set the
Surround MAX on, user audio setting can not be adjusted.
• Flat : The most commanding and natural audio.
• Music : Select this option to enjoy the original sound when listening to the music.
• Movie : Select this option to enjoy sublime sound.
• Sports: Select this option to watch sports broadcasting.
• User : Select this option to use the user-defined audio settings.
User
120Hz
200Hz
500Hz
1.2KHz
3KHz
7.5KHz
12KHz
AVL
To adjust uneven sound volumes across all channels or signals automatically to the most
appropriate level. To use this feature, select On.
Balance Use this function to balance sound from the left and right speakers.
Speaker You can adjust internal speaker status.
If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
Note
When connected to your computer and the 'SSM' setting in the audio menu is Flat, Music, Movie
or Sports, the available menus are Balance, AVL and Surround MAX .
25
Selecting and Adjusting the Screen
Adjusting the timer function
Clock
Off time
On time
Auto sleep
Clock
If the time is on the clock is incorrect, reset the clock manually.
1) Press the MENU button and then use
button to select the TIME menu.
2) Press the
button and then use
button to select the Clock menu.
3) Press the
button and then use
button to set the hour(00~23).
4) Press the
button and then use
button to set the minutes(00~59).
Off / On time The off time automatically switches the set to standby at the pre-set time.
1) Press the MENU button and then use
2) Press the
button and then use
3) Press the
button and then use
4) Press the
button and then use
5) Press the
button and then use
Auto sleep
Note
button to select the TIME menu.
button to select Off time or On time.
button to set the hour(01~23).
button to set the minutes(00~59).
button to select On or Off.
If Auto sleep is active and there is no input signal, the set switches to standby mode
automatically after 10 minutes.
button to select the Auto sleep menu.
1) Press the MENU button and then use
2) Press the
button and then use
button to select On or Off.
In the event of power interruption (disconnection or power failure), the clock must be reset.
Once the on or off time is set, these functions operate daily at the preset time.
Off time function overrides On time function if they are set to the same time.
The set must be in standby mode for the On time to work.
When On time is operated, input screen is turned on as it was turned off.
26
Selecting and Adjusting the Screen
Selecting the options
Language
Child lock
ISM Method
Set ID
Tile Mode
Power Indicator
Logo light
Demo
Language
To choose the language in which the control names are displayed.
Child lock
Use the
buttons to select On or Off. The monitor can be set up so that it can only be
used with the remote control. This feature can prevent unauthorized viewing.
In order to lock the OSD screen adjustment, set the Child lock tab to the 'On' position.
In order to unlock it, do the following :
• Push the MENU button on the remote control and set Child lock to the 'Off' position.
ISM Method
A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods will
result in a ghost image remaining even when you change the image. Avoid allowing a fixed
image to remain on the screen for a long period of time.
Normal : If image sticking is never a problem, ISM is not necessary -set to Normal.
White wash : White wash removes permanent images from the screen.
(An excessive permanent image may be impossible to clear entirely with white wash.
Orbiter : May help prevent ghost images. However, it is best not to allow any fixed image to
remain on the screen. To avoid a permanent image on the screen, the screen will move every 2
minutes.
Inversion : This function inverts the panel colour of the screen. The panel colour is
automatically inverted every 30 minutes.
Orb.+Inv. : This function inverts the panel colour of the screen and may help prevent ghost
images. The panel colour is automatically inverted every 30 minutes and the screen will
move every 2 minutes.
Set ID
Language
Child lock
ISM Method
Set ID
Tile Mode
Power Indicator
1
Logo light
Demo
You can assign a unique Set ID NO (name assignment) to each product when several
products are connected for display. Specify the number (1~99) using the
button
and exit. Use the assigned Set ID to individually control each product using the Product
Control Program.
27
Selecting and Adjusting the Screen
Selecting the options
• To use this function
- Must be displayed with various other products.
- Must be in a function that can be connected to RS-232C or RGB Out
Tile mode
Tile Mode
Child lock
Tile ID
0
ISM Method
Set ID
Tile Mode
Power Indicator
H-Size
0
V-Size
0
Logo light
Demo
• Tile Mode
Off
Language
It is used to enlarge the screen and
also used with several products to
view screen.
H-Position
V-Position
Reset
To set
Tile mode and choose Tile alignment and set the ID of the current product to set
location.
* Only after pressing the SET button the
adjustments made to the settings will be saved.
- Tile mode : row x column ( r = 1, 2, 3, 4 c = 1, 2, 3, 4)
- 4 x 4 available.
- Configuration of an integration screen is also available as well as
configuration of One by one Display.
- Tile mode (product 1 ~ 4) : r(2) x c(2)
row
ID 1
ID 2
column
ID 3
ID 4
28
Selecting and Adjusting the Screen
Selecting the options
- Tile mode (product 1 ~ 9) : r(3) x c(3)
row
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
column
- Tile mode (product 1 ~ 2) : r(2) x c(1)
row
ID 2
ID 1
column
- Tile mode (product 1 ~16) : r(4) x c(4)
row
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
column
ID 9
ID10
ID 11
ID 12
ID 13
ID 14
ID 15
ID 16
29
Selecting and Adjusting the Screen
Selecting the options
Off
Language
Tile Mode
Child lock
Tile ID
0
ISM Method
Set ID
Tile Mode
Power Indicator
H-Size
0
V-Size
0
Logo light
Demo
H-Position
V-Position
Reset
To set
• Tile ID
Select the location of the Tile by setting an ID.
• H Size
Adjust the horizontal size of the screen taking into account the size of the
bezel.
• V Size
Adjust the vertical size of the screen taking into account the size of the bezel.
• H-Position
Moving the screen position horizontally.
• V-Position
Moving the screen position vertically.
• Reset
Function to initialize and release Tile.
All Tile setting are released when selecting Tile recall and the screen returns
to Full screen.
Power
Indicator
Use this function to set the power indicator on the front side of the product to
On or Off.
If you set Off, it will go off. If you set On at any time, the power indicator will
automatically be turned on.
Logo Light
Use this function to set the Logo Display Lamp on the front side of the product to On
or Off. If you set On, the lamp will automatically be turned on.
Demo
Use it to see the difference between XD demo on and XD Demo off.
(XD Demo function is not available in RGB PC/ HDMI/DVI PC mode.)
30
Selecting and Adjusting the Screen
Adjusting Screen CLOCK/PHASE and Position
Auto config.
Manual config.
XGA Mode
ARC
Reset
Auto-config.
(RGB PC
input only)
This button is for the automatic adjustment of the screen position, clock and phase.
This function is suitable for analogue signal input only.
Manualconfig.
If the picture isn't clear after auto adjustment and characters are still trembling, adjust the
picture phase manually.
* Phase, Clock function are not available in RGB DTV, Component, HDMI/DVI DTV.)
To minimize any vertical bars or stripes visible on the screen
Clock
background. The horizontal screen size will also change. This function
is suitable for analogue signal input only
XGA Mode
(RGB-PC
only).
Phase
To adjust the focus of the display. This item allows you to remove any
horizontal noise and clear or sharpen the image of characters. This
function is suitable for analogue signal input only.
H-Position
Moving the screen position horizontally.
V-Position
Moving the screen position vertically.
For more improved or better picture quality, select the same mode corresponding to
computer resolution.
Auto config.
Manual config.
1024x768
XGA Mode
1280x768
ARC
Reset
1360x768
1366x768
31
Selecting and Adjusting the Screen
Adjusting Screen CLOCK/PHASE and Position
ARC
To select the image size of the screen.
Spectacle
When your AV receives the wide screen signal, it will lead you to
adjust the picture horizontally, in a nonlinear proportion, to fill the entire
screen.
Full
When your AV receives the wide screen signal, it will lead you to adjust
the picture horizontally or vertically, in a linear proportion, to fill the entire
screen fully. (Europe an version only)
Original
When your AV receives the wide screen signal, it will be automatically
changed to picture format to be sent.
4:3
This pIcture format is 4:3 of general AV.
16:9
You can enjoy movies (the picture format of 16:9) or general TV
programmes thorough 16:9 mode.
Programmes with 16:9 format are viewed naturally but 4:3 programmes
are magnified on the left and right so that the screen is16:9 format.
1:1
This pIcture format is 1:1 of general AV. (only RGB PC, HDMI/DVI PC)
14:9
You can enjoy the picture format of 14:9 or general AV programmes
through 14:9 mode.
Programmes with 14:9 are viewed naturally, but 4:3 programmes are
magnified on the top/bottom and left/right sides.
Zoom1, 2
You can enjoy movies on a vast screen through Zoom mode.
The 4:3 programmes are magnified on the top/bottom and left/right sides
so that screen is 16:9 format. The bottom and top of the picture may be
lost.
MODE
ARC
AV
Component
HDMI/DVI
DTV
Spectacle
Full
Original
4:3
16:9
14:9
Zoom1
Zoom2
1:1
Reset
Return Manual config. to the default factory settings.
32
RGB
PC
DTV
PC
Troubleshooting
No image is displayed
● Is the product power cord connected?
• See if the power cord is properly connected to the
outlet.
● Is the power indicator light on?
• See if the power switch is turned on.
● Power is on, power indicator is blue but • Adjust brightness and contrast again.
the screen appears extremely dark.
● the power indicator amber?
• If the product is in power saving mode, move the
mouse or press any key.
● Does the 'Out of range' message
appear?
• The signal from the PC (video card) is out of the
vertical or horizontal frequency range of the
product. Adjust the frequency range by referring
to the Specifications in this manual.
* Maximum resolution
RGB : 1600 x 1200 @60Hz
HDMI/DVI : 1280 x 1024 @60Hz
● Does the 'Check signal cable' message • The signal cable between PC and product is not
appear?
connected. Check the signal cable.
• Press the 'INPUT' menu in the remote Control to
check the input signal.
'Unknown Product' message appears when the product is connected.
● Did you install the driver?
• Install the product driver, which is provided with
the product, or download it from the web site.
(http://www.lge.com)
• See if the plug&play function is supported by
referring to the video card user manual.
'Controls Locked' message appears.
Note
• The control locking function prevents unintentional
OSD setting change due to careless usage. To unlock
the controls, simultaneously press the Menu button
and button for several seconds. (You cannot set this
function using the remote control buttons. You can set
this function in the product only.)
▲
● The 'Controls Locked' message
appears when pressing the Menu
button.
* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times
every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second.
The unit is Hz.
* Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the
horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal
frequency. The unit is kHz.
33
Troubleshooting
The screen image looks abnormal.
● Is the screen position wrong?
• D-Sub analog signal – Press the “AUTO” button in
the remote control to automatically select the
optimal screen status that fits into the current
mode. If adjustment is not satisfactory, use the
Position OSD menu.
• See if the video card resolution and frequency are
supported by the product. If the frequency is out of
range, set to the recommended resolution in the
Control Panel – Display – Setting menu.
● Do thin lines appear on the
background screen?
• D-Sub analog signal – Press the “AUTO” button
in the remote control to automatically select an
optimal screen status that fits into the current
mode. If adjustment is not satisfactory, use the
Clock OSD menu.
● Horizontal noise appears or the
characters look blurred.
• D-Sub analog signal – Press the “AUTO” button
in the remote control to automatically select an
optimal screen status that fits into the current
mode. If adjustment is not satisfactory, use the
Phase OSD menu.
● The screen is displayed abnormally.
• The proper input signal is not connected to the
signal port. Connect the signal cable that matches
with the source input signal.
After-image appears on the product.
● After-image appears when the
product is turned off.
• If you use a fixed image for a long time, the pixels
may be damaged quickly. Use the screen-saver
function.
34
Troubleshooting
The audio function does not work.
● No sound?
• See if the audio cable is connected properly.
• Adjust the volume.
• See if the sound is set properly.
• Select the appropriate equalize sound.
● Sound is too dull.
• Adjust the volume.
● Sound is too low.
Screen color is abnormal.
● Screen has poor color resolution
(16 colors).
• Set the number of colors to more than 24 bits (true
color)
Select Control Panel – Display – Settings – Color
Table menu in Windows.
● Screen color is unstable or monocolored.
• Check the connection status of the signal cable.
Or, re-insert the PC video card.
● Do black spots appear on the screen?
• Several pixels (red, green, white or black color)
may appear on the screen, which can be
attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
35
Specifications
The product specifications can change without prior notice for product improvement.
LCD Panel
Power
Dimensions
&Weight
42 inches (106.73 cm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Anti-Glare coating
Visible diagonal size: 106.73 cm
0.681 mm (Pixel Pitch)
Rated Voltage
Power Consumption
AC 100-240V~ 50/60Hz 2.2A
On Mode
: 220W Typ.
Sleep Mode
: ≤ 1W (RGB) / 4W(HDMI/DVI)
Off Mode
: ≤ 1W
[2]
[1]
H
H
W
D
W
D
[4]
[3]
H
H
W
D
W
D
Width x Height x Depth
[1] 99.56 cm (39.19 inches) x 67.41 cm (26.54 inches) x 29.30 cm (11.54 inches)
[2] 99.56 cm (39.19 inches) x 58.76 cm (23.13 inches) x 11.37 cm (4.47 inches)
[3] 112.76 cm (44.39 inches) x 67.41 cm (26.54 inches) x 29.30 cm (11.54 inches)
[4] 112.76 cm (44.39 inches) x 58.76 cm (23.13 inches) x 11.37 cm (4.47 inches)
Net
[1] 24.5 kg (54.02 lbs)
[3] 27.1 kg (59.75 lbs)
[2] 21.1 kg (46.54 lbs)
[4] 23.7 kg (52.25 lbs)
NOTE
Information in this document is subject to change without notice.
36
Specifications
The product specifications can change without prior notice for product improvement.
Video Signal
Max. Resolution
RGB : 1600 X 1200 @60Hz
HDMI/DVI : 1280 X 1024 @60Hz – It may not be supported
depending on the OS or video card type.
Recommended Resolution RGB : WSXGA 1360 X 768 @60Hz
HDMI/DVI : WSXGA 1360 X 768 @60Hz – It may not be
supported depending on the OS or video card type.
Horizontal Frequency
RGB : 30 - 83 kHz
HDMI/DVI : 30 - 72 kHz
Vertical Frequency
56 - 85 Hz
Synchronization Type Separate/Composite/SOG (Sync On Green)/Digital
15-pin D-Sub type, HDMI (digital), S-Video,
Composite Video, Component, RS-232C
Input Connector
Environmental
Conditions
Operational Condition Temperature: 10˚C ~ 35˚C , Humidity: 10% ~ 80%
Storage Condition
Temperature: -20˚C ~ 60˚C , Humidity: 5% ~ 95%
* Applicable only for models that support the speakers
Audio
RMS Audio Output
Input Sensitivity
Speaker Impedance
10W+10W(R+L)
0.7Vrms
8Ω
NOTE
Information in this document is subject to change without notice.
37
Specifications
PC Mode – Preset Mode
Preset mode
1
2
3
4
5
6
7
8
9
10
VGA
VGA
VGA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
31.469
31.468
31.469
37.500
43.269
37.879
46.875
53.674
49.725
48.363
70
70
60
75
85
60
75
85
75
60
Preset mode
11
12
13
14
15
16
17
18
19
VESA 1024 x 768
VESA 1024 x 768
VESA 1280 x 720
VESA 1280 x 768
VESA 1360 x 768
VESA 1366 x 768
VESA 1280 x 1024
VESA 1280 x 1024
VESA 1600 x 1200
Horizontal Vertical
Frequency Frequency
(Hz)
(kHz)
60.123
68.68
44.772
47
47.72
47
63.981
79.98
75.00
RGB : Mode 1 ~ Mode 19
HDMI/DVI : Mode 1 ~ Mode 17
DTV Mode
Component
480i
576i
480p
576p
720p
1080i
o
o
o
o
o
o
RGB(DTV)
x
x
o
o
o
o
HDMI/DVI(DTV)
x
x
o
o
o
o
Power Indicator
Mode
On Mode
Sleep Mode
Off Mode
Product
Blue
Amber
-
NOTE
DTV/PC selection on RGB and HDMI/DVI inputs is available for PC resolutions :
640 X 480/60Hz, 1280 X 720/60Hz and DTV resolutions : 480p, 720p.
38
75
85
60
60
60
60
60
75
60
Specifications
VESA wall mounting
Connected to another object (stand type and wall-mounted type.) This product accepts a VESAcompliant mounting interface pad.- (This has to be purchased separately if required.)
For further information, refer to the VESA Wall Mounting Instruction Guide.
Kensington Security Slot- (This has to be purchased
separately if required.)
Connected to a locking cable that can be purchased
separately at most computer stores
39
Controlling the Multiple Product
RS-232C
Use this method to connect several products to a single PC.
You can control several products at a time by connecting them to a single PC.
Connecting the cable
Connect the RS-232C cable as shown in the picture.
* The RS-232C protocol is used for communication between the PC and product. You can
turn the product on/off, select an input source or adjust the OSD menu from your PC.
RS-232C
(CONTROL &
SERVICE)
RS-232C Cable
(not included)
PC
monitor 1
monitor 3
monitor 2
monitor 4
RS-232C Configurations
3-Wire Configurations (Not Standard)
7-Wire Configurations (Standard RS-232C cable)
PC
RXD
TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
D-Sub 9
(Female)
PC
Monitor
2
3
5
4
6
7
8
RXD
TXD
GND
DTR
DSR
RTS
CTS
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9
(Female)
D-Sub 9
(Male)
Communication Parameter
▲▲ ▲ ▲ ▲▲▲
Baud Rate : 9600buadRate (UART)
Data Length : 8bits
Parity Bit : None
Stop Bit : 1bit
Flow Control : None
Communication Code : ASCII code
Use a straight cable
2
3
5
4
6
7
8
A1
Monitor
2
3
5
4
6
7
8
D-Sub 9
(Male)
TXD
RXD
GND
DSR
DTR
CTS
RTS
RS-232C
Controlling the Multiple Product
Command Reference List
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Lock/ key Lock
14. Balance
15. Color Temperature
16. Abnomal state
17. ISM mode
18. Auto configuration
19. Key
20. Tile Mode
21. Tile H Size
22. Tile V Size
23. Tile ID Set
24. Elapsed time return
25. Temperature value
26. Lamp fault check
COMMAND1
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
m
d
d
d
d
d
d
d
A2
COMMAND2
a
b
c
d
e
f
g
h
i
j
k
l
m
t
u
z
p
u
c
d
g
h
i
l
n
p
DATA(Hexa)
00H - 01H
02H - 09H
01H - 09H
00H - 01H
00H - 01H
00H - 64H
00H - 64H
00H - 64H
00H - 64H
00H - 64H
00H - 64H
00H - 01H
00H - 01H
00H - 64H
00H - 03H
FFH
00H - 08H
01H
Key Code
00H - 44H
00H - 64H
00H - 64H
00H - 10H
FFH
FFH
FFH
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: First command. (j, k, m, d)
* [Command 2]: Second command.
* [Set ID]: Set up the Set ID number of product.
range : 1~99. by setting '0', server can control all products.
* In case of operating with more than 2 sets using set ID as '0' at the same
time, it should not be checked the ack message.
Because all sets will send the ack message, so it's impossible the check the
whole ack messages.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCII code ‘0x0D’
* [ ]: ASCII code Space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Product transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data.
If the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* If there is error, it returns NG
A3
Controlling the Multiple Product
RS-232C
Transmission / Receiving Protocol
▲
01. Power(Command : a)
To control Power On/Off of the Set.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
1 : Power On
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
▲
To show the status of Power On/Off.
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
Data 0 : Power Off
1 : Power On
▲
02. Input Select (Command : b) (Main Picture Input)
To select input source for the Set.
You can also select an input source using the SOURCE
button on the remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 2 : AV
4 : Component 1
5 : Component 2
6 : RGB (DTV)
7 : RGB (PC)
8 : HDMI (DTV)
9 : HDMI (PC)
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
Data 2 : AV
4 : Component 1
5 : Component 2
6 : RGB (DTV)
7 : RGB (PC)
8 : HDMI (DTV)
9 : HDMI (PC)
A4
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
03. Aspect Ratio(Command : c) (Main picture format)
To adjust the screen format.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Screen menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 1 : Normal Screen (4:3)
2 : Wide Screen (16 :9)
3 : Horizon (Spectacle)
4 : Zoom1
5 : Zoom2
6 : Original
7 : 14 : 9
8 : Full (Europe version only)
9 : 1 : 1 (PC)
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
▲
04. Screen Mute(Command : d)
To select screen mute on/off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
A5
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
05. Volume Mute(Command : e)
To control On/Off of the Volume Mute.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
▲
06. Volume Control(Command : f)
To adjust Volume .
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
Data
Min : 00H ~ Max : 64H
• Refer to ‘Real data mapping’ page A7.
A6
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
07. Contrast(Command : g)
To adjust screen contrast.
You can also adjust the contrast in the Picture menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
• Refer to ‘Real data mapping’ as shown below.
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
* Real data mapping
0 : Step 0
:
A : Step 10
:
F : Step 15
10 : Step 16
:
64 : Step 100
▲
08. Brightness(Command : h)
To adjust screen brightness.
You can also adjust the brightness in the Picture menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
• Refer to ‘Real data mapping’ as shown below.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
* Real data mapping
0 : Step
:
A : Step 10
:
F : Step 15
10 : Step 16
:
64 : Step 100
A7
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
09. Color(Command : i) (Video only)
To adjust the screen color.
You can also adjust the color in the Picture menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
• Refer to ‘Real data mapping’ page A7.
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Data
Min : 00H ~ Max : 64H
▲
10. Tint(Command : j) (Video only)
To adjust the screen tint.
You can also adjust the tint in the Picture menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
Red: 00H ~ Green: 64H
(Hexadecimal code)
• Refer to ‘Real data mapping’ page A7.
Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
Data
Red: 00H ~ Green: 64H
* Tint Real data mapping
0 : Step -50
:
64 : Step 50
A8
Controlling the Multiple Product
RS-232C
Transmission / Receiving Protocol
▲
11. Sharpness(Command : k) (Video only)
To adjust the screen Sharpness.
You can also adjust the sharpness in the Picture menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
• Refer to ‘Real data mapping’ page A7.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
Data
Min : 00H ~ Max : 64H
▲
12. OSD Select(Command : l)
To control OSD on/off to the set.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0 : OSD Off
1 : OSD On
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
Data 0 : OSD Off
1 : OSD On
▲
13. Remote Lock /Key Lock (Command : m)
To control Remote Lock on/off to the set.
This function, when controlling RS-232C, locks the remote control and the local keys.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0 : Off
1 : On
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
Data 0 : Off
1 : On
A9
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
14 Balance(Command : t)
To adjust the sound balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
• Refer to ‘Real data mapping’ page A7.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
Data
Min : 00H ~ Max : 64H
* Balance : L50 ~ R50
▲
15. Color Temperature (Command : u)
To adjust the screen color temperature.
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0 : Normal
1 : Cool
2 : Warm
3 : User
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
Data 0 : Normal
1 : Cool
2 : Warm
3 : User
A10
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
16. Abnomal state (Command : z)
Abnormal State : Used to Read the power off status when Stand-by mode.
Transmission
[k][z][ ][Set ID][ ][Data][Cr]
Data FF : Read
0 : Normal (Power on and signal exist)
1: No signal (Power on)
2 : Turn the monitor off by remote control
3 : Turn the monitor off by sleep time function
4 : Turn the monitor off by RS-232C function
6 : AC down
8 : Turn the monitor off by off time function
9 : Turn the monitor off by auto off function
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
▲
17. ISM mode(Command: j p)
Used to select the afterimage preventing function.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 1 : Inversion
2 : Orbiter
3 : Orb.+Inv.
4 : White Wash
8 : Normal
Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
A11
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
18. Auto Configure(Command: j u)
To adjust picture position and minimize image shaking
automatically. it works only in RGB(PC) mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 1 : To set
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
▲
19. Key(Command : m c)
To send IR remote key code.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data Key code : Refer to page A18.
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
A12
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
20. Tile Mode(Command : d d)
Change a Tile Mode.
Transmission
[d][d][][Set ID][][Data][x]
Data
Description
00
Tile mode is off.
12
1 x 2 mode(column x row)
13
1 x 3 mode
14
1 x 4 mode
...
...
44
4 x 4 mode
* The data can not be set to 0X or X0 except 00.
Acknowledgement
[d][][00][][OK/NG][Data][x]
A13
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
21. Tile H Size(Command : d g)
To set the Horizontal size.
Transmission
[d][g][][Set ID][][Data][x]
Data
Min : 00H ~ Max : 64H
Acknowledgement
[g][][Set ID][][OK/NG][Data][x]
▲
22. Tile V Size(Command : d h)
To set the Vertical size.
Transmission
[d][h][][Set ID][][Data][x]
Data
Min : 00H ~ Max : 64H
Acknowledgement
[h][][Set ID][][OK/NG][Data][x]
A14
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
23. Tile ID Set(Command : d i)
To assign the Tile ID for Tiling function .
Transmission
[d][i][][Set ID][][Data][x]
Data
Min : 00H ~ Max : 10H
(Hexadecimal code)
Acknowledgement
[i][][Set ID][][OK/NG][Data][x]
▲
24. Elapsed time return(Command : d l)
To read the elapsed time.
Transmission
[d][l][][Set ID][][Data][x]
* The data is always FF(in Hex).
Acknowledgement
[l][][Set ID][][OK/NG][Data][x]
* The data means used hours.
(Hexadecimal code)
A15
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
25. Temperature value (Command : d n)
To read the inside temperature value.
Transmission
[d][n][][Set ID][][Data][x]
* The data is always FF(in Hex).
Acknowledgement
[n][][Set ID][][OK/NG][Data][x]
* The data is 1 byte long in Hexadecimal.
▲
26. Lamp fault Check(Command : d p)
To check lamp fault.
Transmission
[d][p][][Set ID][][Data][x]
* The data is always FF(in Hex).
Acknowledgement
[p][][Set ID][][OK/NG][Data][x]
Data 0 : Lamp Fault
1: Lamp OK
A16
IR Codes
RS-232C
▲
How to connect
Connect your wired remote control to Remote Control port on the Product.
▲
Output waveform
Remote Control IR Code
single pulse, modulated with 37.917KHz signal at 455KHz
Tc
Carrier frequency
FCAR = 1/Tc = fosc/12
Duty ratio = T1/Tc = 1/3
T1
▲
Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
▲
Lead code
9ms
4.5ms
0.55ms
▲
Repeat code
9ms
2.25ms
▲
Bit description
• Bit "0"
• Bit "1"
0.56ms
0.56ms
1.12ms
2.24ms
▲
Frame interval : Tf
• The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms@455KHz
A17
IR Codes
RS-232C
Note
▲
R/C Button
▼
R/C Button
▲
00
01
02
03
08
C4
C5
09
98
0B
0E
43
5B
6E
44
10
11
12
13
14
15
16
17
18
19
5A
BF
D4
D5
D7
C6
79
76
77
AF
99
Function
VOL( )
R/C Button
▲
Code(Hexa)
VOL( )
R/C Button
POWER ON/OFF
PR/C Button (Power On/Off)
POWER ON
Discrete IR Code(Only Power On)
POWER OFF
Discrete IR Code(Only Power On)
MUTE
R/C Button
AV
INPUT
SLEEP
MENU
EXIT
PSM
SET
R/C Button
Number Key 0
R/C Button
Number Key 1
R/C Button
Number Key 2
R/C Button
Number Key 3
R/C Button
Number Key 4
R/C Button
Number Key 5
R/C Button
Number Key 6
R/C Button
Number Key 7
R/C Button
Number Key 8
R/C Button
Number Key 9
R/C Button
AV
COMPONENT1
COMPONENT2
RGB PC
RGB DTV
HDMI/DVI
ARC
ARC (4:3)
ARC (16:9)
ARC (ZOOM)
AUTO CONFIC
Discrete IR Code(Input AV Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code(Input COMPONENT1 Selection)
Discrete IR Code(Input COMPONENT2 Selection)
Discrete IR Code(Input RGB PC Selection)
Discrete IR Code(Input RGB DTV Selection)
Discrete IR Code(Input HDMI/DVI Selection)
R/C Button
Discrete IR Code(Only 4:3 mode)
Discrete IR Code(Only 16:9 mode)
Discrete IR Code(Only ZOOM1, ZOOM2 mode)
Discrete IR Code
A18
Download PDF

advertising