LG | M4210D-B21 | LG M4210D-B21 Owner’s Manual

User’s Guide
M4210D
Make sure to read the Safety Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your dealer when you ask
for service.
Important
WARRANTY VOID
IF REMOVED
3850TAZ209Y
Warranty void if removed.
To enjoy clearer and more vivid stereoscopic images
See if the resolution is set to Full HD.
The recommended resolution for 3D images is 1920X1080.
If a viewer moves left or right with a distance of more than 4 m, the screen might look dimmed.
Keep a distance of more than 4 m from the product.
4m
* Falls kein 3D-Video genutzt wird, erscheint der Bildschirm verzerrt.
Installing the 3D Player /To enjoy the 3D video
(To view the applicable Guide, click here.)
WARNING -This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
1
Using the Remote Control
Name of the Remote Control Buttons
• Power On/Off Button
• Input Select Button
(See next page)
There is not a function
which is supported
• ARC button
To select the image size of the
screen.
• Auto Button
Automatic adjustment function
(Operational for the analog signal only)
There is not a function
which is supported
• CTR.PWR Button
Turn on the power of the PC built in the
monitor and then turn off.
(The CTR.PWR function operates only
when the PC Control menu is off.)
• Menu Button
1
2
3
4
5
6
7
8
9
CTR.
PWR
0
There is not a function
which is supported
There is not a function
which is supported
• Exit Button
• UP and Down buttons
Bring up and down direction
adjustment.
• Volume
Button
• Check Button
*
• Mute button
There is not a function
which is supported
2
Using the Remote Control
• Input Select Button
If you press the button once,
the following Input Signal
Window will appear. Select
the signal type you want
using the
button.
1
2
3
4
5
6
INPUT
RGB
DVI
7
8
CTR.
PWR
0
9
*
Inserting batteries into remote control.
1. Take out the battery cap.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cap.
• Dispose of used batteries in the recycle bin to prevent
environmental pollution.
AAA Type
3
Name and Function of the Parts
* The product image in the user’s guide could be different from the actual image.
Rear View
REMOTE
CONTROL IN
RS-232C
(CONTROL&
SERVICE)
DVI IN
RGB IN
AUDIO
(RGB/DVI)
LAN
RGB OUT
H/PHONE
OUT
SP/DIF
USB
SERLAL
PORT
OUT
RGB OUT
IN
REMOTE
CONTROL IN
RS-232C
(CONTROL&
SERVICE)
DVI IN
RGB IN
AUDIO
(RGB/DVI)
LAN
RGB OUT
H/PHONE
OUT
SP/DIF
USB
SERLAL
PORT
OUT
RGB OUT
IN
Power Connector : Connect the power cord
Wired Remote Control Port
RS-232C Serial Ports (IN, OUT)
RGB, DVI Ports (IN, OUT)
PC Sound Jack
: Connect the audio cable to the *LINE OUT jack of the PC sound card.
LAN Ports
RGB out Ports
Head Phone out Port
Optical Sound out Ports
USB Ports
Serlal Ports
*LINE OUT
A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that
the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of
PC sound card has only Speaker Out, reduce the PC volume.
If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using
the card jumper of the program (Refer to the Sound Card Manual).
4
Connecting to External Devices
When Connecting to your Built in PC
When connecting with the DVI signal input cable.
1.
Rear side of the product.
REMOTE
CONTROL IN
RS-232C
(CONTROL&
SERVICE)
DVI IN
RGB IN
AUDIO
(RGB/DVI)
LAN
RGB OUT
H/PHONE
OUT
SP/DIF
USB
SERLAL
PORT
OUT
RGB OUT
IN
Connect the power cord.
2.
Turn on power by pressing the power button on the product.
SOURCE
3.
AUTO/SET
ON/OFF
Power button
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
SET
Or, press the SOURCE button at the back side of the product.
SOURCE
AUTO/SET
RGB
DVI
• Select DVI : DVI Digital signal.
4.
INPUT
Install the driver files contained at the supplied CD.
5
Connecting to External Devices
When connecting with the D-Sub signal input cable.
1.
2.
Install the Video driver file contained at the supplied CD.
Rear side of the product.
REMOTE
CONTROL IN
RS-232C
(CONTROL&
SERVICE)
DVI IN
RGB IN
AUDIO
(RGB/DVI)
LAN
RGB OUT
H/PHONE
OUT
SP/DIF
USB
SERLAL
PORT
OUT
RGB OUT
IN
RGB OUT
RGB IN
Connect the power cord.
3.
Turn on power by pressing the power button on the product.
SOURCE
AUTO/SET
ON/OFF
Power button
6
Connecting to External Devices
4.
1
Move the mouse pointer to an
empty area on the Windows
screen (with no icons or task
bars) and click the right
mouse button.
2
When the pop-up menu
appears, click the
'Properties' menu.
1
2
5.
1
Select 'Settings' tab.
2
Click 'Advanced' button.
7
Connecting to External Devices
6.
1
Select
'CATALYST(R)Control
Center' tab.
2
Click 'ATI
CATALYST(R)Control
Center' button.
7.
1
Select 'Display
Manager'menu.
2
8
Select 'Detect
Displays'button.
Connecting to External Devices
8.
1
2
1
Select gray monitor icon and then press the right button of the mouse.
2
Select 'Clone Main with monitor' menu.
9.
Click 'Yes' button.
10.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
SET
Or, press the SOURCE button at the back side of the product.
SOURCE
RGB
AUTO/SET
DVI
• Select RGB : 15-pin D-Sub analog signal.
Note
INPUT
• How to connect to two computers.
Connect the signal cables (DVI and D-Sub) to each computer.
Press the INPUT button in a remote control to select the computer to use.
• Directly connect to a grounded power outlet on the wall or a power bar with a ground
wire.
9
Connecting to External Devices
When Connecting to your PC
1.
First of all, see if the computer, product and the peripherals are turned off.
Then, connect the signal input cable.
A When connecting with the D-Sub signal input cable.
B When connecting with the DVI signal input cable.
A
RGB IN
PC
Rear side of the product.
B
DVI IN
Rear side of the product.
PC
Connect the Audio cable.
AUDIO
(RGB/DVI)
PC
Rear side of the product.
Connect the power cord.
REMOTE
CONTROL IN
RS-232C
(CONTROL&
SERVICE)
DVI IN
RGB IN
AUDIO
(RGB/DVI)
LAN
RGB OUT
H/PHONE
OUT
SP/DIF
USB
SERLAL
PORT
OUT
RGB OUT
IN
Rear side of the product.
Note
• User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to
maintain standard compliance for the product.
10
Connecting to External Devices
2.
1 Turn on power by pressing the power button on the product.
SOURCE
AUTO/SET
ON/OFF
Power button
2 Turn on the PC.
3.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
SET
Or, press the SOURCE button at the back side of the product.
SOURCE
AUTO/SET
A
When connecting with a D-Sub signal input cable.
• Select RGB : 15-pin D-Sub analog signal.
B
When connecting with a DVI signal input cable.
• Select DVI : DVI Digital signal.
Note
INPUT
INPUT
RGB
RGB
DVI
DVI
• How to connect to two computers.
Connect the signal cables (DVI and D-Sub) to each computer.
Press the INPUT button in a remote control to select the computer to use.
• Directly connect to a grounded power outlet on the wall or a power bar with a ground
wire.
11
Connecting to External Devices
Watching RGB Outputs
Use this function when displaying ANALOG RGB inputs of a PC to the other product.
• To use different products connected to each other
Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT
connector of product 1 and connect the other end to the RGB IN connector of other
products.
15-pin D-Sub Signal Cable
RGB IN
RGB IN
RGB IN
RGB IN
RGB OUT
RGB OUT
RGB OUT
RGB OUT
PC
PC
Product 1
Note
Product 2
Product 3
Product 4
• When multi-connecting in/out cascade format, cables to be less damaged are recommended.
We recommend that you should use cable distributor.
12
Selecting and Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
SOURCE
SOURCE
Power Button
AUTO/SET
AUTO/SET
ON/OFF
ON/OFF
• Press this button to turn on the power. Press this button again to
turn it off.
Power Indicator
• This Indicator lights up blue when the display operates normally(on
mode). If the display is in sleep (Power Saving) mode, this indicator
color changes to amber.
MENU Button
• Use this button to show/hide the OSD (On Screen Display) menu
screen.
OSD Select /
Adjust Button
• Use this button to select an icon or adjust the setting in the OSD screen.
13
Selecting and Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
AUTO/SET Button
If the resolution is 1920X1080 (RGB Mode)
Auto in progress
If the resolution is not 1920X1080 (RGB Mode)
Auto in progress
For optimal display
Change resolution to 1920 X 1080
* See if the resolution is set to Full.
The recommended resolution for 3D images is 1920X1080.
SOURCE Button
• Select the input signal
DVI (Digital signal)
RGB(Analog signal)
Digital signal and Analogue signal can't be outputted at the same time so
when transferring the source connect the connector and then turn on the
power.
IR Receiver
• The unit that receives the signal from the remote control.
This IR Receiver lights up blue when the display operates normally
(on mode). If the display is in sleep (Power Saving) mode,
this indicator color changes to amber.
14
Selecting and Adjusting the Screen
OSD Menu
Icon
Function Description
Adjusts screen brightness, contrast and color that you prefer.
PICTURE
Adjusts the audio function.
SOUND
Adjust the time function
TIMER
Adjusts the screen status according to the circumstances.
SPECIAL
Adjusts the screen video.
SCREEN
Note
OSD(On Screen Display)
The OSD function enables you to adjust the screen status conveniently since it provides
graphical presentation.
15
Selecting and Adjusting the Screen
How to adjust the OSD (On Screen Display) screen
Pops up
the menu
screen
Move where
you want to
adjust
Select a
menu icon
Move where
you want to
adjust
Select a
menu icon
Adjust the status
Save
adjustment
Exit from the
menu screen.
• Use the remote control to adjust the OSD screen.
1
Press the MENU Button, then the main menu of the OSD appears.
2
To access a control, use the
3
When the icon you want becomes highlighted, press the SET Button.
4
Use the
5
Accept the changes by pressing the SET Button.
6
Exit the OSD by pressing the EXIT Button.
Buttons.
Buttons to adjust the item to the desired level.
How to adjust the screen automatically
You need to adjust the screen display when
connecting the product to a new computer or changing
the mode. Refer to the following section to set an
optimal product screen.
If the resolution is 1920X1080 (RGB Mode)
Auto in progress
If the resolution is not 1920X1080 (RGB Mode)
Press the AUTO/SET button (AUTO button in a
remote Control) in the PC analog signal. Then, an
optimal screen status will be selected that fits into the
current mode.
If adjustment is not satisfactory, you need to adjust
screen position, clock and phase in the OSD menu.
16
Auto in progress
For optimal display
Change resolution to 1920 X 1080
Selecting and Adjusting the Screen
Adjusting Screen Color
CSM
• 6500K/9300K
Selecting a factory setting color set.
6500K: Slightly reddish white.
9300K: Slightly bluish white.
CSM
• User : Select this option to use
the user-defined settings.
Contrast
To adjust the contrast of the screen.
Brightness
To adjust the brightness of the screen.
Red / Green / Blue
Set your own color levels.
CSM
17
Selecting and Adjusting the Screen
Adjusting the audio function
SSM
The best sound tone quality will be
selected automatically depending on the
video type that you're currently watching.
SOUND
SSM
Flat
Balance
Music
Movie
Sports
User
• Flat : The most commanding and natural audio.
• Music : Select this option to enjoy the original sound when listening to the music.
• Movie : Select this option to enjoy sublime sound.
• Sports: Select this option to watch sports broadcasting.
• User : Select this option to use the user-defined audio settings.
Balance
Use this function to balance sound from the left
SOUND
SSM
Balance
and right speakers.
0
L
Note
R
When connected to your computer and the 'SSM' setting in the audio menu is one of Flat, Music,
Movie or Sports, the available menus are Balance.
18
Selecting and Adjusting the Screen
TIME ID to adjust the time function
TIMER
Clock
MNT Off timer
MNT On timer
PC Off timer
PC On timer
This function is used to set up of current time.
1) Press the MENU button and then use
button to select the TIMER menu.
2) Press the
button and then use
button to select the Clock menu.
button and then use
button to set the hour(00~23).
3) Press
4) Press
button and then use
button to set the minutes(00~59).
5) Press the OK/MENU button to save.
Clock
MNT Off timer/ The Off time automatically switches the set to off mode at the pre-set time.
button to select the TIMER menu.
MNT On timer 1) Press the MENU button and then use
2) Press the
button and then use
button to select MNT Off time or MNT On time.
3) Press the
button and then use
button to select On or Off.
4) Press the
button and then use
button to set the hour(00~23).
5) Press the
button and then use
button to set the minutes(00~59).
button to adjust volume level.
6) Only On time function; Press the
button and then
7) Press the OK/MENU button to save.
PC Off timer/
PC On timer
Note
The Off time automatically switches the PC to off mode at the pre-set time.
(PC Off/On timer menu is activated only when PC Control in Sepcial menu is off.)
1) Press the MENU button and then use
button to select the TIMER menu.
2) Press the
button and then use
button to select PC Off time or PC On time.
3) Press the
button and then use
button to select On or Off.
4) Press the
button and then use
button to set the hour(00~23).
button to set the minutes(00~59).
5) Press the
button and then use
6) Press the OK/MENU button to save.
• Once the On or Off time is set, these functions operate daily at the preset time.
• Off time function overrides On time function if they are set to the same time.
• The set must be in off mode for the On time to work.
19
Selecting and Adjusting the Screen
Selecting the options
Reset
Input
If you press the button once, the following
Input Signal Window will appear. Select
the signal type you want using the
button.
Reset
Child lock
Use the
buttons to select On or Off. The Set can be set up so that it can only be used
with the remote control. This feature can prevent unauthorized viewing.
In order to lock the OSD screen adjustment, set the Child lock tab to the 'On' position.
In order to unlock it, do the following :
* Push the MENU button on the remote control and set Child lock to the 'Off' position.
Language
To choose the language in which the control names are displayed.
Power
indicator
Use this function to set the power indicator on the front side of the product to On or Off.
If you set Off, it will go off. If you set On at any time, the power indicator will
automatically be turned on.
Transparency
To adjust the transparency of the OSD menu screen.
20
Selecting and Adjusting the Screen
Selecting the options
• To use this function
- You can connect the product with several other products and use the Tile mode function.
Tile mode
Tile mode
Off
It is used to enlarge the screen and also used with
several products to view screen,
H-Size
0
V-Size
0
H-Position
V-Position
Reset
Reset
ID
• Tile mode
Tile mode and choose Tile alignment and set the ID of the current product to set location.
• H Size
Adjust the horizontal size of the screen taking into account the size of the bezel.
• V Size
Adjust the vertical size of the screen taking into account the size of the bezel.
• H-Position
Adjust the horizontal position of the screen taking into account the size of the bezel.
• V-Position
Adjust the vertical position of the screen taking into account the size of the bezel.
• Reset
Function to initialize and release Tile. All Tile setting are released when selecting.
Tile recall and the screen returns to Full screen.
• ID
Select the location of the Tile by setting an ID.
21
Selecting and Adjusting the Screen
Selecting the options
• Tile mode
- Tile mode : row x column ( r = 1, 2, 3, 4 c = 1, 2, 3, 4)
- 4 x 4 available.
- Configuration of an integration screen is also available as well as configuration of one by one Display.
- Tile mode (product 1 ~ 4) : r(2) x c(2)
row
ID 1
ID 2
column
ID 3
ID 4
- Tile mode (product 1 ~ 9) : r(3) x c(3)
row
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
22
column
Selecting and Adjusting the Screen
Selecting the options
- Tile mode (product 1 ~ 2) : r(2) x c(1)
row
ID 2
ID 1
column
Reset
Use this function to reset the product to the factory default. However, language selection
and PC Control selection will not be initialized.
Set ID
Set ID
Logo light
You can assign a unique Set ID NO (name
assignment) to each product when several
products are connected for display. Specify
the number (1~99) using the
button
and exit. Use the assigned Set ID to
individually control each product using the
Product Control Program.
ID
1
PC Control
Logo Light
Use this function to set the Logo Display Lamp on the front side of the product to On
or Off. If you set On, the lamp will automatically be turned on.
PC Control
You can change the power setting of the PC built in the monitor.
On : Turn on/off both the monitor and the built-in PC.
Off : Turn on/off the built-in PC only.
* How to turn on or off the PC built in the monitor after setting it to Off?
(a) Press the power button while the SOURCE button is being pressed on the rear side of the monitor.
(b) Or, press the CRT.PWR button at the remote control.
23
Selecting and Adjusting the Screen
Adjusting Screen CLOCK/PHASE and Position
Auto-configure
ARC
To select the image size of the screen.
(1:1 menu are not supported over 1920 X 1080 resolution)
Auto-configure
Auto-configure
This button is for the automatic adjustment of the screen position, clock and phase.
This function is suitable for analoge singnal input only.
Clock
To minimize any vertical bars or stripes visible on the screen background. The horizontal
screen size will also change. This function is suitable for analoge singnal input only.
Phase
To adjust the focus of the display. This item allows you to remove any horizontal noise
and clear or sharpen the image of characters. This function is suitable for analoge
singnal input only.
To adjust position of the screen.
This function is suitable for analoge singnal
input only.
Position
Auto-configure
H-Position
0
V-Position
0
24
Troubleshooting
No image is displayed
● Is the product power cord connected?
• See if the power cord is properly connected to the
outlet.
● Is the power indicator light on?
• See if the power switch is turned on.
● Power is on, power indicator is green
but the screen appears extremely dark.
• Adjust brightness and contrast again.
● Is the power indicator amber?
• If the product is in power saving mode, move the
mouse or press any key.
● Does the 'Out of range' message
appear?
• The signal from the PC (video card) is out of the
vertical or horizontal frequency range of the
product. Adjust the frequency range by referring
to the Specifications in this manual.
* Maximum resolution
RGB : 1920 X 1080 @60Hz
DVI : 1920 X 1080 @60Hz
● Does the 'Power saving mode' On DVI • Connect the RGB cable, and then change the
input source to 'RGB'.
message appear?
And then, press the MENU button to set the PC
Control value of the SPECIAL menu to 'On'.
Disconnect RGB cable, and turn off the power,
and then turn on the power again.
● Does the 'Check signal cable' message
appear?
• The signal cable between PC and product is not
connected. Check the signal cable.
• Press the 'INPUT' menu in the remote Control to
check the input signal.
● Did you check the INPUT Key?
• Press the 'INPUT' menu in the remote Control to
check the input signal.
Note
* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times
every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second.
The unit is Hz.
* Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the
horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal
frequency. The unit is kHz.
25
Troubleshooting
The screen image looks abnormal.
● Is the screen position wrong at the
RGB mode?
• Press the “AUTO” button in the remote control to
automatically select the optimal screen status that
fits into the current mode. If adjustment is not
satisfactory, use the Position OSD menu.
• See if the video card resolution and frequency are
supported by the product. If the frequency is out of
range, set to the recommended resolution in the
Control Panel – Display – Setting menu.
● Do thin lines appear on the
background screen at the
RGB mode?
• Press the “AUTO” button in the remote control to
automatically select an optimal screen status that
fits into the current mode. If adjustment is not
satisfactory, use the Clock OSD menu.
● Horizontal noise appears or the
characters look blurred at the
RGB mode.
• Press the “AUTO” button in the remote control to
automatically select an optimal screen status that
fits into the current mode. If adjustment is not
satisfactory, use the Phase OSD menu.
● The screen is displayed abnormally at
the RGB mode.
• The proper input signal is not connected to the
signal port. Connect the signal cable that matches
with the source input signal.
The audio function does not work.
● No sound?
• See if the audio cable is connected properly.
• Adjust the volume.
• See if the sound is set properly.
• Select the appropriate equalize sound.
● Sound is too dull.
• Adjust the volume.
● Sound is too low.
26
Troubleshooting
'Child lock on' message appears.
● The 'Child lock on' message
appears when pressing the Menu
button.
Push the MENU button on the remote control and set
Child lock to the 'Off' position.
After-image appears on the product.
● After-image appears when the
product is turned off.
• If you use a fixed image for a long time, the pixels
may be damaged quickly. Use the screensaver
function.
Screen color is abnormal.
● Screen has poor color resolution
(16 colors).
• Set the number of colors to more than 32 bits (true
color)
Select Control Panel – Display – Settings – Color
Table menu in Windows.
● Do black spots appear on the screen?
• Several pixels (red, green, white or black color)
may appear on the screen, which can be
attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
The operation does not work normally.
● The power suddenly turned off.
• Is the sleep timer set?
• Check the power control settings.
Power interrupted.
• "CAUTION! FAN STOP!"
If the power is turned off after this message
appears, it means that the fan is out of order.
In this case, contact your local service center.
27
Specifications
The product specifications can change without prior notice for product improvement.
LCD Panel
Power
42 inches visible diagonal (106.72 cm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
0.681 mm (Pixel Pitch)
Rated Voltage
Power Consumption
AC 100-240V~ 50/60Hz 2.7A
On Mode
: 270W Typ.(with PC), 240W Typ.(only Monitor)
Sleep Mode
: ≤ 20W (only Monitor), 60W(with PC),
Off Mode
: ≤ 5W
Dimensions
&Weight
H
W
D
Width x Height x Depth
99.56 cm (39.19 inches) x 58.76 cm (23.13 inches) x 11.37 cm (4.47 inches)
Net
22.3 kg (49.16 lbs)
NOTE
Information in this document is subject to change without notice.
28
Specifications
The product specifications can change without prior notice for product improvement.
Video Signal
Max. Resolution
RGB : 1920 X 1080 @60Hz
DVI : 1920 X 1080 @60Hz
Recommended Resolution RGB : WUXGA 1920 X 1080 @60Hz
DVI : WUXGA 1920 X 1080 @60Hz
Horizontal Frequency
RGB : 30 - 83 kHz
DVI : 30 - 83 kHz
Vertical Frequency
56 - 60 Hz (RGB / DVI)
Synchronization Type Separate/Composite/Digital
15-pin D-Sub type, DVI (digital), RS-232C
Input Connector
Environmental
Conditions
Operational Condition Temperature: 5˚C ~ 35˚C , Humidity: 10% ~ 80%
Storage Condition
Temperature: -20˚C ~ 60˚C , Humidity: 5% ~ 95%
NOTE
Information in this document is subject to change without notice.
29
Specifications
PC Mode – Preset Mode
Preset mode
1
2
3
4
5
6
7
8
9
640 x 350
720 x 400
640 x 480
800 x 600
1024 x 768
1280 x 720
1280 x 1024
1680 x 1050
1920 x 1080
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
31.468
31.469
31.469
37.879
48.363
44.772
63.981
65.290
66.587
70
70
59
60
60
59
60
59
59
Power Indicator
Mode
On Mode
Sleep Mode
Off Mode
Product
Blue
Amber
-
30
Specifications
VESA wall mounting
Connected to another object (stand type and wall-mounted type.) This product accepts a VESAcompliant mounting interface pad.- (This has to be purchased separately if required.)
For further information, refer to the VESA Wall Mounting Instruction Guide.
Kensington Security Slot- (This has to be purchased
separately if required.)
Connected to a locking cable that can be purchased
separately at most computer stores
31
Specifications
Signal Connector Pin Assignment
8
16
24
1
9
17
DVI-D Connector
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal(DVI-D)
Pin
16
17
18
19
20
21
22
23
24
T. M. D. S. Data2T. M. D. S. Data2+
T. M. D. S. Data2/4 Shield
T. M. D. S. Data4T. M. D. S. Data4+
DDC Clock
DDC Data
Analog Vertical Sync.
T. M. D. S. Data1T. M. D. S. Data1+
T. M. D. S. Data1/3 Shield
T. M. D. S. Data3T. M. D. S. Data3+
+5V Power
Ground (return for +5V,
Signal(DVI-D)
Hot Plug Detect
T. M. D. S. Data0T. M. D. S. Data0+
T. M. D. S. Data0/5 Shield
T. M. D. S. Data5T. M. D. S. Data5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock-
H. Sync. and V. Sync.)
T. M. D. S. (Transition Minimized Differential Signaling)
32
Specifications
Connecting the USB(Universal Serial Bus) Cable
"USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals conveniently to
your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to
your display instead of having to connect them to your computer. This will give you greater flexibility in setting up
your system. USB allows you to connect a chain of up to 120 devices on a single USB port; and you can “hot”
plug (attach them while the computer is running) or unplug them while maintaining the Plug and the Plug auto
detection and configuration. This display has an integrated BUS-powered USB hub, allowing up to 2 other USB
devices to be attached it.
1.
2.
Connect the upstream port of the display to the downstream port of the USB compliant
PC or another hub using the USB cable.
Connect the USB compliant peripherals to the downstream ports of the display.
RGB OUT
H/PHONE
OUT
SP/DIF
USB
SERLAL
PORT
USB downstream Port
connect the cables from USB
compliant peripherals-such as
keyboard, mouse, etc
3. The monitor’s USB terminal supports USB 2.0 and High Speed cables.
Data Rate
Power
Consumption
High Speed
Full Speed
Low Speed
480Mbps
12Mbps
1.5Mbps
2.5W
(Max,each Port)
2.5W
2.5W
(Max,each Port)
(Max,each Port)
NOTE
To activate the USB hub function, the display must be connected to a USB compliant
PC(OS) or another hub with the USB cable(enclosed).
When connecting the USB cable, check that the shape of the connector at the cable side
matches the shape at the connecting side.
Even if the display is in a power saving mode, USB compliant devices will function when
they are connected the USB ports(both the upstream and downstream) of the display.
33
Controlling the Multiple Product
RS-232C
Use this method to connect several products to a single PC.
You can control several products at a time by connecting them to a single PC.
Connecting the cable
Connect the RS-232C cable as shown in the picture.
* The RS-232C protocol is used for communication between the PC and product. You can
turn the product on/off, select an input source or adjust the OSD menu from your PC.
Product 1
Product 2
Product 3
Product 4
RS-232C
(CONTROL&
SERVICE)
RS-232C
(CONTROL&
SERVICE)
RS-232C
(CONTROL&
SERVICE)
RS-232C
(CONTROL&
SERVICE)
OUT
OUT
OUT
OUT
IN
IN
IN
IN
RS-232C Cable
RS-232C Cable
RS-232C Cable
RS-232C Configurations
3-Wire Configurations (Not Standard)
7-Wire Configurations (Standard RS-232C cable)
PC
RXD
TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
D-Sub 9
(Female)
PC
Monitor
2
3
5
4
6
7
8
RXD
TXD
GND
DTR
DSR
RTS
CTS
TXD
RXD
GND
DSR
DTR
CTS
RTS
2
3
5
4
6
7
8
D-Sub 9
(Female)
D-Sub 9
(Male)
Communication Parameter
▲▲ ▲ ▲ ▲▲▲
Baud Rate : 9600buadRate (UART)
Data Length : 8bits
Parity Bit : None
Stop Bit : 1bit
Flow Control : None
Communication Code : ASCII code
Use a straight cable
1
Monitor
2
3
5
4
6
7
8
D-Sub 9
(Male)
TXD
RXD
GND
DSR
DTR
CTS
RTS
RS-232C
Controlling the Multiple Product
Command Reference List
01. Power
02. Main Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. OSD Select
10. Remote On/Off
11. Balance
12. Select Color Temp
13. Auto Configure
14. Red Gain Adjust
15. Green Gain Adjust
16. Blue Gain Adjust
17. Tiling Mode
18. Tile H Position
19. Tile V Position
20. Tile H Size
21. Tile V Size
22. Tile ID Set
23. Temperature Check
24. Inverter Adjust
25. PC Power On/Off
26. PC Control On/Off
27. Input Select
COMMAND1
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
j
d
d
d
d
d
d
d
d
d
d
x
2
COMMAND2
a
b
c
d
e
f
g
h
l
m
t
u
u
w
y
z
d
e
f
g
h
i
n
r
s
t
b
DATA(Hexa)
00H - 01H
01H,07H, 09H
08H, 09H
00H - 01H
00H - 01H
00H - 64H
00H - 64H
00H - 64H
00H - 01H
00H - 01H
00H - 64H
00H - 02H
01H
00H - 64H
00H - 64H
00H - 64H
00H - 44H
00H - 64H
00H - 64H
00H - 64H
00H - 64H
00H - 10H
FFH
00H - 01H
00H - 01H
00H - 01H
01H,06H, 08H
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: First command. (k)
* [Command 2]: Second command. (a ~ u)
* [Set ID]: You can adjust the set ID to choose desired product
ID number in Special menu. Adjustment range is 1 ~99.
When selecting Set ID ‘0’, every connected
set is controlled. Set ID is indicated as decimal
(1~255) on menu and as Hexa decimal (0x0~0x64)
on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCII code ‘0x0D’
* [ ]: ASCII code Space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Product transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data.
If the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Product transmits ACK (acknowledgement) based on
this format when receiving abnormal data from non-viable
functions or communication errors.
Data 1: Illegal Code
2: Not supported function
3: Wait more time
3
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
01. Power On(Command : a)
To control Power On/Off of the Set.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
1 : Power On
ff: Read Status
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
▲
To show the status of Power On/Off.
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Data 0 : Power Off
1 : Power On
ff: Read Status
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
* The Product transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
▲
02. Main input Select(Command : b) (Main Picture Input)
To select input source for the Set.
You can also select an input source using the INPUT
button on the remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 1 : RGB
7 : RGB
9 : DVI
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
4
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
03. Aspect Ratio(Command : c) (Main picure format)
To adjust the screen format.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Screen menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 8 : Full mode
9 : 1:1 (
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
▲
04. Screen Mute(Command : d)
To select screen mute on/off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
5
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
05. Volume Mute(Command : e)
To control On/Off of the Volume Mute.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
▲
06. Volume Control(Command : f)
To adjust Volume .
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
Data
Min : 00H ~ Max : 64H
• Refer to ‘Real data mapping’ page 7.
6
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
07. Contrast(Command : g)
To adjust screen contrast.
You can also adjust the contrast in the Picture menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
• Refer to ‘Real data mapping’ as shown below.
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
* Real data mapping
0 : Step 0
:
A : Step 10
:
F : Step 15
10 : Step 16
:
64 : Step 100
▲
08. Brightness(Command : h)
To adjust screen brightness.
You can also adjust the brightness in the Picture menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
• Refer to ‘Real data mapping’ as shown below.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
* Real data mapping
0 : Step
:
A : Step 10
:
F : Step 15
10 : Step 16
:
64 : Step 100
7
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
09. OSD Select(Command : l)
To control OSD on/off to the set.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0 : OSD Off
1 : OSD On
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
Data 0 : OSD Off
1 : OSD On
▲
10. Remote On/Off (Command : m)
Lock the buttons at the rear side of the monitor and the button at the remote control.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0 : Off
1 : On
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
Data 0 : Off
1 : On
▲
11. Balance (Command : t)
To adjust the sound balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
32H : Center
00H : Left
64H : Right
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
32H : Center
00H : Left
64H : Right
8
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
12. Select Color Temp (Command : u)
To adjust the screen color temperature.
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0 : User
1 : 9300K
2 : 6500K
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
Data 0 : User
1 : 9300K
2 : 6500K
▲
13. Auto Configure(Command: j u)
To adjust picture position and minimize image shaking
automatically. it works only in RGB(PC) mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 1 : To set
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
9
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
14. Red Gain Adjust (Command: j w)
To adjust Red color level.
Transmission
[j][w][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
Acknowledgement
[w][ ][Set ID][ ][OK][Data][x]
* When it is executed with the 6500K or 9300K selected, it is automatically changed to the USER.
▲
15. Green Gain Adjust (Command: j y)
To adjust Green color level.
Transmission
[j][y][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
* When it is executed with the 6500K or 9300K selected, it is automatically changed to the USER.
▲
16. Blue Gain Adjust (Command: j z)
To adjust Blue color level.
Transmission
[j][z][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
* When it is executed with the 6500K or 9300K selected, it is automatically changed to the USER.
10
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
17. Tiling Mode (Command :d d)
Change a Tiling Mode.
Transmission
[d][d][][Set ID][][Data][x]
Data
Description
00
Tiling mode is off.
12
1 x 2 mode(column x row)
13
1 x 3 mode
14
1 x 4 mode
...
...
44
4 x 4 mode
* The data can not be set to 0X or X0 except 00.
Acknowledgement
[d][][00][][OK/NG][Data][x]
▲
18. Tile H Position (Command : d e)
To set the horizontal position.
Transmission
[d][e][][Set ID][][Data][x]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
Acknowledgement
[e][][Set ID][][OK/NG][Data][x]
11
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
19. Tile V Position(Command : d f)
To set the Vertical position.
Transmission
[d][f][][Set ID][][Data][x]
* The data range is from 00 to 64(in Hex).
Acknowledgement
[f][][Set ID][][OK/NG][Data][x]
▲
20. Tile H Size(Command : d g)
To set the Horizontal size.
Transmission
[d][g][][Set ID][][Data][x]
* The data range is from 00 to 64(in Hex).
Acknowledgement
[g][][Set ID][][OK/NG][Data][x]
▲
21. Tile V Size(Command : d h)
To set the Vertical size.
Transmission
[d][h][][Set ID][][Data][x]
* The data range is from 00 to 64(in Hex).
Acknowledgement
[h][][Set ID][][OK/NG][Data][x]
12
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
22. Tile ID Set (Command : d i)
To assign the Tile ID for Tiling function.
Transmission
[d][i][][Set ID][][Data][x]
* The data range is from 00 to 10 tile mode. (in Hex).
Acknowledgement
[i][][Set ID][][OK/NG][Data][x]
▲
23. Temperature check (Command : d n)
To read the inside temperature value.
Transmission
[d][n][][Set ID][][Data][x]
* The data is always FF(in Hex).
Acknowledgement
[n][][Set ID][][OK/NG][Data][x]
Data are 1 byte long in Hex ASCII format.
▲
24. Inverter Adjust (Command : d r)
To adjust the Inverter.
Transmission
[d][r][][Set ID][][Data][x]
Data 0 : Inverter Off
1 : Inverter On
Acknowledgement
[r][][Set ID][][OK/NG][Data][x]
13
RS-232C
Controlling the Multiple Product
Transmission / Receiving Protocol
▲
25. PC Power On/Off (Command : d s)
To turn On and Off the built in PC.
Transmission
[d][s][][Set ID][][Data][x]
Data 0 : PC Power Off
1 : PC Power On
Acknowledgement
[s][][Set ID][][OK/NG][Data][x]
*This operates only when ‘PC Control’ is ‘Off’.
▲
26. PC Control On/Off (Command : d t)
It sets the synchronized power on/off between the built-in PC of the monitor and the monitor.
Transmission
[d][t][][Set ID][][Data][x]
Data 0 : Off
1 : On
Acknowledgement
[t][][Set ID][][OK/NG][Data][x]
▲
27. Input Selection (Command : b) (Main Picture Input)
To select input source for the Set.
You can also select an input source using the INPUT
button on the remote control.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data 01 : RGB
06 : RGB
08 : DVI
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
14
IR Codes
RS-232C
▲
How to connect
Connect your wired remote control to Remote Control port on the Product.
Remote Control IR Code
▲
Output waveform
single pulse, modulated with 37.917KHz signal at 455KHz
Tc
Carrier frequency
FCAR = 1/Tc = fosc/12
Duty ratio = T1/Tc = 1/3
T1
▲
Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
▲
Lead code
9ms
4.5ms
0.55ms
▲
Repeat code
9ms
2.25ms
▲
Bit description
• Bit "0"
• Bit "1"
0.56ms
0.56ms
1.12ms
2.24ms
▲
Frame interval : Tf
• The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms@455KHz
15
IR Codes
RS-232C
Note
▲
R/C Button
▼
R/C Button
▲
00
01
02
03
08
C4
C5
09
0B
43
5B
44
10
11
12
13
14
15
16
17
18
19
D5
C6
79
77
AF
Function
VOL( )
R/C Button
▲
Code(Hexa)
VOL( )
R/C Button
POWER ON/OFF
R/C Button (Power On/Off)
POWER ON
Discrete IR Code(Only Power On)
POWER OFF
Discrete IR Code(Only Power On)
MUTE
R/C Button
INPUT
MENU
EXIT
SET
R/C Button
Number Key 0
R/C Button
Number Key 1
R/C Button
Number Key 2
R/C Button
Number Key 3
R/C Button
Number Key 4
R/C Button
Number Key 5
R/C Button
Number Key 6
R/C Button
Number Key 7
R/C Button
Number Key 8
R/C Button
Number Key 9
R/C Button
RGB
DVI
ARC
ARC (1:1)
AUTO CONFIC
Discrete IR Code(Input RGB PC Selection)
R/C Button
R/C Button
R/C Button
Discrete IR Code(Input DVI Selection)
R/C Button
Discrete IR Code(Only 1:1 mode)
Discrete IR Code
16
P/NO : 3840TRL098E (0801-REV00)
Download PDF