OWNER’S MANUAL
Blu-ray™/ DVD
Home Theater System
Please read this manual carefully before operating
your set and retain it for future reference.
BH4120S (BH4120S, S42S2-S, S42S1-W)
Getting Started
3
Safety Information
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION : CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
1
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
4
Getting Started
This device is equipped with a portable battery or
accumulator.
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Young Children should be supervised to ensure
that they do not play with appliance.
• If the appliance is supplied from a cord
extension set or an electrical portable outlet
device, the cord extension set on electrical
portable outlet device must be positioned so
that it is not subject to splashing or ingress of
moisture.
Getting Started
Notes on Copyrights
yy Furthermore, BD-ROM Mark and BD+ are
additionally used as content protection systems
for Blu-ray Disc format, which imposes certain
restrictions including playback restrictions for
BD-ROM Mark and/or BD+ protected contents.
To obtain additional information on AACS, BDROM Mark, BD+, or this product, please contact
an authorized Customer Service Centre.
yy Many BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should only
connect your player directly to your TV, not to a
VCR. Connecting to a VCR results in a distorted
picture from copy-protected discs.
yy This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
yy Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/
or criminal liability.
Important Notice for TV colour
system
The colour system of this player differs according to
currently playing discs.
For example, when the player plays the disc
recorded in the NTSC colour system, the image is
output as an NTSC signal.
Only the multi system colour TV can receive all
signals output from the player.
yy If you have a PAL colour system TV, you will see
just distorted images when using discs or video
contents recorded in NTSC.
yy The multi system colour TV changes the colour
system automatically according to input signals.
In case that the colour system is not changed
automatically, turn it off and then on to see
normal images on screen.
yy Even if the disc recorded in NTSC colour system
are well displayed on your TV, these may not be
recorded correctly on your recorder.
1
Getting Started
yy Because AACS (Advanced Access Content
System) is approved as content protection
system for Blu-ray Disc format, similar to use of
CSS (Content Scramble System) for DVD format,
certain restrictions are imposed on playback,
analog signal output, etc., of AACS protected
contents. The operation of this product and
restrictions on this product may vary depending
on your time of purchase as those restrictions
may be adopted and/or changed by AACS after
the production of this product.
5
6
Table of Contents
Table of Contents
1
Getting Started
3
Safety Information
8Introduction
8
– Playable Discs and symbols used in
this manual
9
– About the “7” Symbol Display
9
– Compatibility Notes
10 – File compatibility
11 – AVCHD (Advanced Video Codec High
Definition)
12 – Certain System Requirements
12 – Regional Code
12 – System Select (Optional)
13 Remote control
14 Front panel
15 Rear panel
2Connecting
16
17
17
18
18
19
20
21
21
21
22
22
22
Positioning the system
Speaker Connection
– Attaching the speakers to the player
Connecting to Your TV
– HDMI Connection
– Video Connection
– Resolution Setting
Antenna connection
Connections with external device
– AUX Connection
– PORT. IN connection
USB device connection
– Playback content in the USB device
3 System Setting
24Settings
24 – Initial Setup
25 – Adjust the Setup Settings
25 – [DISPLAY] Menu
27 – [LANGUAGE] Menu
27 – [AUDIO] Menu
29 – [LOCK] Menu
30 – [OTHERS] Menu
31 Sound Effect
4 Operating
32
32
32
32
33
33
33
34
34
34
34
35
35
35
36
36
36
37
38
38
39
39
39
39
40
40
40
41
42
42
42
42
42
42
General Playback
– Using [HOME] menu
– Playing a Disc
– Playing a file on a disc/USB device
– Basic operations for video and audio
content
– Basic operations for photo content
– Using the disc menu
– Resume playback
– Last Scene Memory
Advanced Playback
– Repeat Playback
– Repeating a specific portion
– Viewing content information
– Changing content list view
– Selecting a subtitle file
– Changing the mode
– Options while viewing a photo
– Listening to music while slide show
On-Screen display
– Displaying content information onscreen
– Playing from selected time
– Selecting a subtitle language
– Hearing a different audio
– Watching from a different angle
– Changing the TV Aspect Ratio
– Changing subtitle code page
– Changing the Picture Mode
Audio CD Recording
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting a saved station
– Deleting all the saved stations
– Improving poor FM reception
5Troubleshooting
43Troubleshooting
43 – General
44 – Picture
Table of Contents
7
44 – Sound
44 – Customer Support
44 – Open source software notice
6Appendix
45 Controlling a TV with the Supplied
Remote Control
45 – Setting up the remote to control your
TV
46 Area Code List
47 Language code List
48 Trademarks and Licenses
50 Audio Output Specifications
51Specifications
53Maintenance
53 – Handling the Unit
53 – Notes on Discs
1
2
3
4
5
6
8
Getting Started
Introduction
1
Playable Discs and symbols used in this manual
Getting Started
Media/Term
Logo
Symbol
e
Blu-Ray
y
u
i
r
DVD-ROM
Description
yy Discs such as movies that can be purchased or
rented.
yy BD-R/RE discs that are recorded in BDAV format.
yy BD-R/RE discs that contain Movie, Music or
Photo files.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
yy Discs such as movies that can be purchased or
rented.
yy Movie mode and finalized only
yy Supports the dual layer disc also
DVD-R
DVD-RW
DVD+R
DVD+RW
(8 cm, 12 cm)
o
Finalized AVCHD format
y
u
i
yy DVD±R/RW discs that contain Movie, Music or
Photo files.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
DVD-RW
(VR)
(8 cm, 12 cm)
r
Audio CD
(8 cm, 12 cm)
t
CD-R/RW
(8 cm, 12
cm)
y
u
i
yy CD-R/RW discs that contain Movie, Music or
Photo files.
,
>
Indicates special notes and operating features.
Note
–
Caution
–
VR mode and finalized only
Audio CD
yy ISO 9660+JOLIET, UDF and UDF Bridge format
Indicates cautions for preventing possible
damages from abuse.
Getting Started
,,Note
yy Depending on the recording software & the
finalization, some recorded discs (CD-R/RW,
DVD±R/RW, BD-R/RE) may not be playable.
yy BD-R/RE, DVD±R/RW and CD-R/RW discs
recorded using a personal computer or a
DVD or CD Recorder may not play if the
disc is damaged or dirty, or if there is dirt or
condensation on the player’s lens.
yy If you record a disc using a personal
computer, even if it is recorded in a
compatible format, there are cases in which
it may not play because of the settings of
the application software used to create the
disc. (Check with the software publisher for
more detailed information.)
yy This player requires discs and recordings to
meet certain technical standards in order to
achieve optimal playback quality.
yy Pre-recorded DVDs are automatically set to
these standards. There are many different
types of recordable disc formats (including
CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions
to ensure compatible playback.
yy Customers should note that permission
is required in order to download MP3 /
WMA files and music from the Internet.
Our company has no right to grant such
permission. Permission should always be
sought from the copyright owner.
yy You have to set the disc format option
to [Mastered] in order to make the discs
compatible with the LG players when
formatting rewritable discs. When setting
the option to Live System, you cannot use
it on LG player. (Mastered/Live File System :
Disc format system for windows Vista)
About the “7” Symbol Display
“7” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
Compatibility Notes
yy Because BD-ROM is a new format, certain disc,
digital connection and other compatibility issues
are possible. If you experience compatibility
problems, please contact an authorized
Customer Service Center.
yy This unit allows you to enjoy functions such
as picture-in-picture, secondary audio and
Virtual packages, etc., with BD-ROM supporting
BONUSVIEW (BD-ROM version 2 Profile 1 version
1.1). Secondary video and audio can be played
from a disc compatible with the picture-inpicture function. For the playback method, refer
to the instructions in the disc.
yy Viewing high-definition content and upconverting standard DVD content may require a
HDMI-capable input or HDCP-capable DVI input
on your display device.
yy Some BD-ROM and DVD discs may restrict the
use of some operation commands or features.
yy Dolby TrueHD, Dolby Digital Plus and DTS-HD are
supported with maximum 5.1 channels if you
use HDMI connection for the audio output of the
unit.
1
Getting Started
yy Depending on the conditions of the
recording equipment or the CD-R/RW (or
DVD±R/RW) disc itself, some CD-R/RW (or
DVD±R/RW) discs cannot be played on the
unit.
9
10
Getting Started
File compatibility
Movie files
1
Getting Started
File
Location
File
Extension
Disc,
USB
“.avi”, “.divx”,
“.mpg”, “.mpeg”,
“.mkv”, “.mp4”,
“.asf”, “.wmv”,
“.m4v” (DRM
free), “.vob”,
“.3gp”, ".mov",
".trp", ".m2t",
".mpe", ".m1v",
".m2v", ".wm"
Codec Format
DIVX3.xx, DIVX4.xx,
DIVX5.xx, DIVX6.xx
(Standard playback
only), XVID, MPEG1 SS,
H.264/MPEG-4 AVC,
MPEG2 PS, MPEG2 TS,
VC-1 SM (WMV3)
Audio Format
Dolby Digital,
DTS, MP3,
WMA, AAC,
AC3
Subtitle
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), VobSub
(.sub), SubViewer 1.0 (.sub),
SubViewer 2.0 (.sub/.txt), TMPlayer
(.txt), DVD Subtitle System (.txt)
Music files
File
Location
File
Extension
Disc,
USB
“mp3”, “.wma”,
“.wav”, “.m4a”
(DRM free),
“.flac”
Sampling Frequency
Bitrate
within 32 - 48 kHz (WMA), within 32 - 192 kbps
within 16 - 48 kHz (MP3) (WMA), within
32 - 320 kbps (MP3)
Note
Some wav files are
not supported on this
player.
Photo files
File
Location
Disc,
USB
File
Extension
“.jpg”, “.jpeg”,
“.png”, “.gif”
Recommended
Size
Note
Less than 4,000 x 3,000 x 24 bit/pixel Progressive and lossless
Less than 3,000 x 3,000 x 32 bit/pixel compression photo image files
are not supported.
Getting Started
,,Note
yy The file name is limited to 180 characters.
yy Maximum files/folder: Less than 2 000
(total number of files and folders)
yy The file requirements on page 10 are not
always compatible. There may have some
restrictions by file features.
yy This unit cannot support the ID3 Tag
embedded MP3 file.
yy The total playback time of audio file
indicated on the screen may not correct for
VBR files.
yy HD movie files contained on the CD, DVD or
USB 1.0/1.1 may not played properly. Blu-ray
Disc or USB 2.0 are recommended to play
back HD movie files.
yy This player supports H.264/MPEG-4 AVC
profile Main, High at Level 4.1. For a file
with higher level, the warning message will
appear on the screen.
yy This player does not support files that are
recorded with GMC*1 or Qpel*2.
*1 GMC – Global Motion Compensation
*2 Qpel – Quarter pixel
,,Note
yy A “avi” file which is encoded “WMV 9 codec”
is not supported.
yy This player supports UTF-8 files even it
contains Unicode subtitle contents. This
player can not support the pure Unicode
subtitle files.
yy Depending on the types of file or ways of
recording, it may not play back.
yy A disc which was recorded by multi-session
on normal PC is not supported on this
player.
yy To be playback a movie file, movie file name
and Subtitle file name must be the same.
yy If video codec is MPEG2 TS or MPEG2 PS,
subtitle does not play back.
yy The total playback time of music file
indicated on the screen may not correct for
VBR files.
yy Video/ Audio codec compatibility may differ
depending on the video file.
AVCHD (Advanced Video
Codec High Definition)
yy This player can playback AVCHD format discs.
These discs are normally recorded and used in
camcorders.
yy The AVCHD format is a high definition digital
video camera format.
yy The MPEG-4 AVC/H.264 format is capable of
compressing images at higher efficiency than
that of the conventional image compressing
format.
yy This player can playback AVCHD discs using
“x.v.Color” format.
yy Some AVCHD format discs may not play
depending on the recording condition.
yy AVCHD format discs need to be finalized.
yy “x.v.Color” offers a wider color range than normal
DVD camcorder discs.
1
Getting Started
yy Depending on the size and number of the
files, it may take several minutes to read the
contents on the media.
11
12
1
Getting Started
Certain System Requirements
Regional Code
For high definition video playback:
This unit has a regional code printed on the rear of
the unit. This unit can play only BD-ROM or DVD
discs labeled same as the rear of the unit or “ALL”.
yy High definition display that has HDMI input jack.
yy BD-ROM disc with high definition content.
Getting Started
yy HDMI or HDCP capable DVI input on your display
device is required for some content (as specified
by disc authors).
System Select (Optional)
You must select the appropriate system mode for
your TV system. Open the disc tray using the B
(OPEN/CLOSE) button and then, press and hold M
(PAUSE) for more than five seconds to be able to
select a system (PAL, NTSC, AUTO)
Getting Started
13
Remote control
FUNCTION
• • • • • • c • • • • • •
SPEAKER LEVEL: Sets the sound
level of desired speaker.
SUBTITLE: Selects a subtitle
language.
1 (POWER): Switches the player
ON or OFF.
MUTE: Mute the unit.
SLEEP: Sets a certain period of
time after which the unit will
switch to off.
Colored (R, G, Y, B) buttons:
- Use to navigate BD-ROM menus.
They are also used for [MOVIE],
[PHOTO], [MUSIC] menu.
- B button: Selects mono/ stereo
in FM mode.
HOME ( ): Displays or exits the
[Home Menu].
DISC MENU: Accesses menu on a
disc.
• • • • • • b • • • • • •
Direction buttons: Selects an
option in the menu.
PRESET +/-: Selects programme
of Radio.
TUNING +/-: Tunes in the desired
radio station.
ENTER (b): Acknowledges menu
selection.
BACK ( ): Exits the menu or
returns to the previous screen.
TITLE/POPUP: Displays the DVD
title menu or BD-ROM’s pop-up
menu, if available.
Z (STOP): Stops playback.
d (PLAY): Starts playback.
M (PAUSE/STEP): Pauses
playback.
Remove the battery cover on the
rear of the Remote Control, and
insert R03 (size AAA) battery with
4 and 5 matched correctly.
VOL +/-: Adjusts speaker volume.
B (OPEN/CLOSE): Ejects a disc.
INFO/MENU (m): Displays or
exits On-Screen Display.
Battery Installation
SOUND EFFECT: Selects a sound
effect mode.
C/V (SKIP): Goes to the
next or previous chapter / track /
file.
c/v (SCAN): Searches
backward or forward.
X (REC): Registra un CD Audio.
0-9 numerical buttons: Selects
numbered options in a menu.
CLEAR: Removes a mark on the
search menu or a number when
setting the password.
REPEAT (h): Repeats a desired
section or sequence.
AUDIO: Selects an audio language
or audio channel.
? : Marked button is not available.
• • • • • • d • • • • • •
TV Control Buttons: See page
45.
1
Getting Started
INFO/MENU
• • • • • • a • • • • • • FUNCTION: Changes input mode.
14
Getting Started
Front panel
1
Getting Started
a Disc tray
b Display Window
c PORT. IN
d USB Port
e Operation buttons
R (Open / Close)
T (Play / Pause)
I (Stop)
F (Function)
Changes the input source or function.
f Volume
g1 (Power)
Getting Started
15
Rear panel
1
Getting Started
a AC power cord
f HDMI OUT TO TV
b Speakers connectors
g VIDEO OUT
c Cooling Fan
d Antenna Connector
e AUX (L/R) INPUT
C
G
Connecting
16
F
A
D
2
A
A
Positioning the system
E
A
The following illustration shows an example of
positioning the system. Note that the illustrations
Ain these instructions differ from the actual unit for
explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position (A). A B C D E F G
Connecting
B
C
A
A
A
GB
B
A
yy Before using the subwoofer, remove the
protective vinyl.
G
F
C
A
A
A
E
E
A
E
A
A
D
A
A
E
A ABCD E F G
speaker (L)/
A A Front
B Cleft
D
EE F G
A D right
speaker (R):
C
A A B Front
EE F G
A
Place the front speakers to the sides of the monitor
or screen and as flush with the screen surface as
possible.
E
F G
A AA
B C Center
D E speaker:
Place the center speaker above or below the
monitor or screen.
A A B C D Surround
E F G left speaker (L)/
right speaker (R):
F G
A B C D E Surround
A
Place these speakers behind your listening position,
E
facing slightly inwards.
B C D E F Subwoofer:
G
The position of the subwoofer is not so critical,
because low bass sounds are not highly directional.
But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of
the room to reduce the wall reflections.
C D E F G Unit
yy Place the center speaker at a safe distance
from the child’s reach.
Otherwise it may result in the speaker falling
down and causing personal injury and/or
property damage.
yy The speakers contain magnetic parts, so
colour irregularity may occur on the CRT
TV screen or PC monitor screen. Please use
the speakers away from the TV screen or PC
monitor screen.
B
B
C
CG
G
A
B A
A A
>>Caution
yy Be careful to make sure children not to put
their hands or any objects into the *speaker
duct.
*Speaker duct: A hole for plentiful bass
sound on speaker cabinet (enclosure).
Connecting
Speaker Connection
17
2. Connect the black stripe of each wire to the
terminals marked - (minus) and the other end
to the terminals marked + (plus).
Attaching the speakers to the
player
1. To connect the cable to the unit, press each
plastic finger pad to open the connection
terminals on the unit. Insert the wire and release
the finger pad.
2
Connecting
Speaker
Position
Rear
Rear right
Rear
Rear left
Center
Center
Sub woofer
Any front position
Front
Front right
Front
Front left
18
Connecting
Connecting to Your TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
yy HDMI connection (page 18)
yy Video connection (page 19)
2
HDMI Connection
If you have a HDMI TV or monitor, you can connect
it to this player using a HDMI cable (Type A, High
speed HDMI™ cable with Ethernet). Connect the
HDMI jack on the player to the HDMI jack on a
HDMI compatible TV or monitor.
,,Note
Connecting
yy Depending on your TV and other equipment
you wish to connect, there are various ways
you could connect the player. Use only one
of the connections described in this manual.
Rear of the unit
yy Please refer to the manuals of your TV,
stereo system or other devices as necessary
to make the best connections.
yy Make sure the player is connected directly
to the TV. Tune the TV to the correct video
input channel.
yy Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
HDMI cable
TV
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
Additional Information for HDMI
yy When you connect a HDMI or DVI compatible
device make sure of the following:
-- Try switching off the HDMI/DVI device and
this player. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this player.
-- The connected device’s video input is set
correctly for this unit.
-- The connected device is compatible with
720x576p, 1280x720p, 1920x1080i or
1920x1080p video input.
yy Not all HDCP-compatible HDMI or DVI devices
will work with this player.
-- The picture will not be displayed properly
with non-HDCP device.
Connecting
,,Note
yy If a connected HDMI device does not accept
the audio output of the player, the HDMI
device’s audio sound may be distorted or
may not output.
yy When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 20.)
Video Connection
Connect the VIDEO OUT jack on the player to the
video in jack on the TV using a video cable. You can
hear the sound through the system’s speakers.
Rear of the unit
yy Select the type of video output from the
HDMI OUT jack using [HDMI Color Setting]
option on the [Setup] menu (see page
26).
yy When the HDMI connection with HDCP
is not verified, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
yy If there are noises or lines on the screen,
please check the HDMI cable (length is
generally limited to 4.5 m(15 ft.)).
2
Connecting
yy Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the player and then turn it
on again.
19
Video cable
TV
20 Connecting
Resolution Setting
The player provides several output resolutions for
HDMI OUT jack. You can change the resolution
using [Setup] menu.
1. Press HOME ( ).
2. Use A/D to select the [Setup] and press ENTER
(b). The [Setup] menu appears.
2
3. Use W/S to select [DISPLAY] option then
press D to move to the second level.
Connecting
4. Use W/S to select the [Resolution] option
then press ENTER (b) to move to the third level.
5.Use W/S to select the desired resolution then
press ENTER (b) to confirm your selection.
,,Note
yy If your TV does not accept the resolution
you have set on the player, you can set
resolution to 576p as follows:
1.Press B to open the disc tray.
2Press Z (STOP) for more than 5 seconds.
yy When you set the resolution to 576i with
HDMI connection, actual resolution is
outputted to 576p.
yy If you select a resolution manually and then
connect the HDMI jack to TV and your TV
does not accept it, the resolution setting is
set to [Auto].
yy If you select a resolution that your TV
does not accept, the warning message
will appear. After resolution change,
if you cannot see the screen, please
wait 20 seconds and the resolution will
automatically revert back to the previous
resolution.
yy The 1080p video output frame rate may
be automatically set to either 24 Hz or
50 Hz depending both on the capability
and preference of the connected TV and
based on the native video frame rate of the
content on the BD-ROM disc.
yy The resolution of the VIDEO OUT jack is
always outputted at 576i resolution.
Connecting
Antenna connection
Connect the supplied antenna for listening to the
radio.
21
Connections with
external device
AUX Connection
You can enjoy the sound from an external
component through the speakers of this system.
You can also use the F (Function) button on the
front panel to select the input mode.
Rear of the unit
Rear of the unit
,,Note
After connecting the FM wire antenna, keep it
as horizontal as possible. Be sure to fully extend
the FM wire antenna.
Red
White
To the audio output jacks
of your component
(TV, VCR, etc.)
2
Connecting
Connect the analog audio output jacks of your
component into the AUX L/R (INPUT) on this unit.
And then select the [AUX] option by pressing
FUNCTION and ENTER (b).
22 Connecting
PORT. IN connection
You can enjoy the sound from your portable audio
player through the speakers of this system.
Connect the headphones (or line out ) jack of the
portable audio player into the PORT. IN socket of
this unit. And then select the [PORTABLE] option by
pressing FUNCTION and ENTER (b).
2
You can also use the F (Function) button on the
front panel to select the input mode.
USB device connection
This player can play movie, music and photo files
contained in the USB device.
Playback content in the USB
device
1. Insert a USB device to the USB port until it fits
into place.
Connecting
MP3 player, etc...
When you connect the USB device on the HOME
menu, the player plays a music file contained in the
USB storage device automatically. If the USB storage
device is containing various types of files, a menu
for the file type selection will appear.
File loading may takes few minutes depending on
the number of content stored in the USB storage
device. Press ENTER (b) while [Cancel] is selected
to stop loading.
2.Press HOME ( ).
3. Select [Movie], [Photo] or [Music] using A/D,
and press ENTER (b
4. Select the [USB] option using W/S, and press
ENTER (b).
5. Select a file using W/S/A/D, and press
PLAY or ENTER (b) to play the file.
6. Withdraw the USB device carefully.
Connecting 23
,,Note
yy This player supports USB flash drive/external
HDD formatted in FAT16, FAT32 and NTFS
when accessing files (music, photo, movie).
yy This unit can support up to 4 partitions of
the USB device.
yy Do not extract the USB device during
operation (play, etc.).
yy USB device: USB device that supports
USB1.1 and USB2.0.
yy Movie, music and photo files can be played.
For details of operations on each file, refer to
relevant pages.
yy Regular back up is recommended to prevent
data loss.
yy If you use a USB extension cable, USB HUB
or USB Multi-reader, the USB device may not
be recognized.
yy Some USB device may not work with this
unit.
yy Digital camera and mobile phone are not
supported.
yy USB Port of the unit cannot be connected
to PC. The unit cannot be used as a storage
device.
2
Connecting
yy A USB device which requires additional
program installation when you have
connected it to a computer, is not
supported.
24 System Setting
Settings
4. Check all the settings that you have set in the
previous steps.
Initial Setup
When you turn on the unit for the first time, the
initial setup wizard appears on the screen. Set the
display language, speaker setup on the initial setup
wizard.
1.Press 1 (POWER).
The initial setup wizard appears on the screen.
2.Use W/S/A/D to select a display language
and press ENTER (b).
3
System Setting
3. Press ENTER (b) to verify the test tone signals of
the speakers.
After verifying the test tone signals, press ENTER
(b) while [Stop] is highlighted. Select [Next]
and press ENTER (b).
Press ENTER (b) while [Finish] is highlighted
to finish the initial setup settings. If there is any
settings to be changed, use A/D to select
[Previous] and press ENTER (b).
System Setting 25
Adjust the Setup Settings
[DISPLAY] Menu
You can change the settings of the player in the
[Setup] menu.
TV Aspect Ratio
1.Press HOME ( ).
Select a TV aspect ratio option according to your TV
type.
[4:3 Letter Box]
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars
above and below the picture.
2.Use A/D to select the [Setup] and press
ENTER (b). The [Setup] menu appears.
[4:3 Pan Scan]
Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
Select when a 16:9 wide TV is connected. The
4:3 picture is displayed with an original 4:3
aspect ratio, with black bars appearing at the
left and right sides.
3.Use W/S to select the first setup option, and
press D to move to the second level.
[16:9 Full]
Select when a 16:9 wide TV is connected. The
4:3 picture is adjusted horizontally (in a linear
proportion) to fill the entire screen.
,,Note
You cannot select [4:3 Letter Box] and
[4:3 Pan Scan] option when the resolution is
set to higher than 720p.
4.Use W/S to select a second setup option, and
press ENTER (b) to move to the third level.
5.Use W/S to select a desired setting, and press
ENTER (b) to confirm your selection.
3
System Setting
[16:9 Original]
26 System Setting
Resolution
HDMI Color Setting
Sets the output resolution of the HDMI video signal.
Refer to page 20 for details about the resolution
setting.
Select the type of output from the HDMI OUT jack.
For this setting, please refer to the manuals of your
display device.
[Auto]
[YCbCr]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV.
Select when connecting to a HDMI display
device.
[1080p]
[RGB]
Select when connecting to a DVI display
device.
Outputs 1080 lines of progressive video.
[1080i]
3
Outputs 1080 lines of interlaced video.
System Setting
[720p]
Outputs 720 lines of progressive video.
[576p]
Outputs 576 lines of progressive video.
[576i]
Outputs 576 lines of interlaced video.
1080p Display Mode
When the resolution is set to 1080p, select
[24 Hz] for smooth presentation of film material
(1080p/24 Hz) with a HDMI-equipped display
compatible with 1080p/24 Hz input.
,,Note
yy When you select [24 Hz], you may
experience some picture disturbance when
the video switches video and film material.
In this case, select [50 Hz].
yy Even when [1080p Display Mode] is set to
[24 Hz], if your TV is not compatible with
1080p/24 Hz, the actual frame frequency of
the video output will be 50 Hz to match the
video source format.
Home Menu Guide
This function allows you to display or delete the
guide bubble on the Home Menu. Set this option
to [On] for displaying guide.
System Setting 27
[LANGUAGE] Menu
[AUDIO] Menu
Display Menu
Each disc has a variety of audio output options. Set
the player’s Audio options according to the type of
audio system you use.
Select a language for the [Setup] menu and onscreen display.
Disc Menu/Disc Audio/
Disc Subtitle
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the
disc was recorded.
Press ENTER (b) to select another language.
Use number buttons then press ENTER (b)
to enter the corresponding 4-digit number
according to the language code list on page
47.
[Off] (Disc Subtitle only)
Turn off Subtitle.
,,Note
Depending on the disc, your language setting
may not work.
Digital Output
[PCM Stereo] (HDMI only)
Select if you connect this unit’s HDMI OUT jack
to a device with two-channel digital stereo
decoder.
[PCM Multi-Ch] (HDMI only)
Select if you connect this unit’s HDMI OUT jack
to a device with multi-channel digital decoder.
[DTS Re-Encode] (HDMI only)
Select if you connect this unit’s HDMI OUT jack
to a device with DTS decoder.
[Bit Stream] (HDMI only)
Select if you connect this unit’s HDMI OUT jack
to a device with LPCM, Dolby Digital, Dolby
Digital Plus, Dolby TrueHD, DTS and DTS-HD
decoder.
,,Note
yy When [Digital Output] option is set to [PCM
Multi-Ch], the audio may output as PCM
Stereo if the PCM Multi-Ch information is
not detected from HDMI device with EDID.
yy If the [Digital Output] option is set to [DTS
Re-Encode], the DTS Re-Encode audio is
outputted for BD-ROM discs with secondary
audio and the original audio is outputted for
the other discs (like [Bit Stream]).
yy This setting is not available on the input
signal from an external device.
3
System Setting
[Other]
,,Note
Since many factors affect the type of audio
output, see “Audio Output Specifications” on
page 50 for details.
28 System Setting
Speaker Setup
HD AV Sync
To obtain the best possible sound, use the speaker
setup display to specify the volume of the speakers
you have connected and their distance from your
listening position. Use the test to adjust the volume
of the speakers to the same level.
Sometimes Digital TV encounters a delay between
picture and sound. If this happens you can
compensate by setting a delay on the sound so
that it effectively ‘waits’ for the picture to arrive: this
is called HD AV Sync. Use W S to scroll up and
down through the delay amount, which you can
set at anything between 0 and 300 ms.
DRC (Dynamic Range Control)
This function allows you to listen to a movie at a
lower volume without losing clarity of sound.
[Off]
3
Turns off this function.
System Setting
[Speaker]
[On]
Select a speaker that you want to adjust.
Compress the dynamic range of the Dolby
Digital, Dolby Digital Plus or Dolby TrueHD
audio output.
[Volume]
Adjust the output level of each speaker.
[Distance]
Adjust the distance between each speaker and
the listening position.
[Test/ Stop test tone]
The speakers will emit a test tone.
[OK]
Confirms the setting.
[Cancel]
Cancels the setting.
[Auto]
The dynamic range of the Dolby TrueHD audio
output is specified by itself.
And the dynamic range of the Dolby Digital
and Dolby Digital Plus are operated as same as
the [On] mode.
,,Note
The DRC setting can be changed only when a
disc is not inserted or the unit is in complete
stop mode.
System Setting 29
[LOCK] Menu
DVD Rating
The [LOCK] settings affect only BD-ROM and DVD
playback.
Blocks playback of rated DVD based on their
content. (Not all discs are rated.)
To access the any features in [LOCK] settings, you
must enter the 4-digit security code you have
created.
If you have not entered a password yet, you are
prompted to do so. Enter a 4-digit password twice,
and press ENTER (b) to create a new password.
Password
You can create or change the password.
[None]
[Change]
Enter the current password and press ENTER
(b). Enter a 4-digit password twice, and press
ENTER (b) to create a new password.
If you forget your password
If you forget your password, you can clear it using
the following steps:
1. Remove any disc that might be in the player.
2. Select [Password] option in the [Setup] menu.
3. Use Number buttons to enter “210499”. The
password is cleared.
,,Note
If you make a mistake before pressing ENTER
(b), press CLEAR. Then input the correct
password.
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select [Unlock], parental control is not
active and the disc plays in full.
Blu-ray Disc Rating
Set an age limit of BD-ROM play. Use number
buttons to input an age limit for BD-ROM viewing.
[255]
All BD-ROM can be played.
[0-254]
Prohibits play of BD-ROM with corresponding
ratings recorded on them.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 46.
3
System Setting
Enter a 4-digit password twice, and press
ENTER (b) to create a new password.
[Rating 1-8]
30 System Setting
[OTHERS] Menu
DivX(R) VOD
ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX, LLC, a subsidiary of Rovi Corporation.
This is an official DivX Certified® device that plays
DivX video. Visit divx.com for more information and
software tools to convert your files into DivX videos.
3
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete
your registration.
System Setting
[Register]
Auto Power Off
The screen saver appears when you leave the
player in Stop mode for about five minutes. If
you set this option to [On], the unit automatically
turns off within 20 minutes since the Screen Saver
is displayed. Set this option to [Off ] to leave the
screen saver until the unit is operated by the user.
,,Note
When you set [Auto Power Off ] function in
setting menu on, this unit will be off itself to
save electronic consumption in the case main
unit is not connected to external device and is
not used for 25 minutes.
So does this unit after six hours since Main unit
has been connected to other device using
analog input.
Displays the registration code of your player.
[Deregister]
Deactivate your player and display the
deactivation code.
,,Note
All the downloaded videos from DivX(R) VOD
with this player’s registration code can only be
played on this unit.
Initialize
[Factory Set]
You can reset the player to its original factory
settings.
[Blu-ray Storage Clear]
Initializes the Blu-ray contents from the
connected USB storage.
Software
[Information]
Displays the current software version.
System Setting
Sound Effect
31
Setting the [User EQ]
You can select a suitable sound mode. Press SOUND
EFFECT repeatedly until the desired mode appears
on the front panel display or the TV screen. The
displayed items for the equalizer maybe different
depending on sound sources and effects.
[Natural Plus]: You can enjoy the natural sound
effect same as 5.1 channel.
[Natural]: You can enjoy comfortable and natural
sound.
1.Use W/S to select the desired frequency.
[Bypass]: Software with multichannel surround
audio signals is played according to the way it was
recorded.
Select [Cancel] option then press ENTER (b) to
cancel the setting.
Select [Reset] option then press ENTER (b) to reset
the all adjustments.
[Loudness]: Improves bass and treble sound.
[User EQ]: You can adjust the sound by raising or
lowering the level of specific frequency.
3
System Setting
[Bass Blast]: Reinforce the bass sound effect from
front left and right speaker and subwoofer.
2.Use A/D to select the desired level.
32 Operating
General Playback
Playing a Disc
erot
Using [HOME] menu
1.Press B (OPEN/CLOSE), and place a disc on the
disc tray.
The home menu appears when you press HOME
( ). Use A/D to select a category and press
ENTER (b).
2.Press B (OPEN/CLOSE) to close the disc tray.
For the most Audio CD, BD-ROM and
DVD-ROM discs, playback starts automatically.
3.Press HOME ( ).
4. Select [Movie] or [Music] using A/D, and press
ENTER (b).
5. Select [Blu-ray Disc], [DVD], [VR] or [Audio]
option using W/S, and press ENTER (b).
,,Note
4
yy Playback functions described in this manual
are not always available in every files and
media. Some functions can be restricted
depending on many factors.
a [Music] - Plays audio contents.
Operating
yy Depending on the BD-ROM titles, a USB
device connection may be needed for the
proper playback.
b [Movie] - Plays video contents.
c [Photo] - Plays photo contents.
yy Unfinalized DVD VR format discs may not be
played in this player.
d [Input] - Changes input mode.
e [Setup] - Adjusts the system settings.
yy Some DVD-VR discs are made with CPRM
data by DVD RECORDER. This unit cannot
support these kinds of discs.
Playing a file on a disc/USB
device
yui
This player can play movie, music and photo files
contained in the disc or USB device.
1. Insert a data disc on the tray or connect a USB
device.
The unit plays only music file contained in the
USB storage device or disc automatically.
2.Press HOME ( ).
3. Select [Movie], [Photo] or [Music] using A/D,
and press ENTER (b).
4. Select [Data] or [USB] option using W/S, and
press ENTER (b).
5. Select a file using W/S/A/D, and press
d(PLAY) or ENTER (b) to play the file.
Operating 33
Basic operations for video and
audio content
Basic operations for photo
content
To stop playback
To play a slide show
Press Z (STOP) while playback.
Press d (PLAY) to start slide show.
To pause playback
To stop a slide show
Press M (PAUSE) while playback.
Press d (PLAY) to resume playback.
Press Z (STOP) while slide show.
To play frame-by-frame (Video)
Press M (PAUSE) while movie playback.
Press M (PAUSE) repeatedly to play Frame-by-Frame
playback.
To scan forward or backward
Press c or v to play fast forward or fast reverse
during playback.
To pause a slide show
Press M (PAUSE) while slide show.
Press d (PLAY) to re-start the slide show.
To skip to the next/previous photo
While viewing a photo in full screen, press A or D
to go to the previous or next photo.
Using the disc menu
ero
To slow down the playing speed
To display the disc menu
While the playback is paused, press v repeatedly
to play various speeds of slow motion.
The menu screen may be displayed first after
loading a disc which contains a menu. If you want
to display the disc menu while playback, press DISC
MENU.
To skip to the next/previous
chapter/track/file
During playback, press C or V to go to the
next chapter/track/file or to return to the beginning
of the current chapter/track/file.
Press C twice briefly to step back to the previous
chapter/track/file.
Use W/S/A/D buttons to navigate through
menu items.
To display the Pop-up menu
Some BD-ROM discs contain Pop-up menu that
appears while playback.
Press TITLE/POPUP while playback, and use W/S/
A/D buttons to navigate through menu items.
4
Operating
You can change the various playback speeds by
pressing c or v repeatedly.
34 Operating
Resume playback
eroyt
u
The unit records the point where you pressed the
Z (STOP) depending on the disc.
If “MZ (Resume Stop)” appears on the screen briefly,
press d (PLAY) to resume playback (from the scene
point).
If you press Z (STOP) twice or unload the disc,
“Z(Complete Stop)” appears on the screen. The unit
will clear the stopped point.
,,Note
yy The resume point may be cleared when a
button is pressed (for example; 1 (POWER),
B (OPEN/CLOSE), etc).
yy On BD-ROM discs with BD-J, the resume
playback function does not work.
4
Operating
yy If you press Z (STOP) once during BD-ROM
interactive title playback, the unit will be in
Complete Stop mode .
Advanced Playback
Repeat Playback
erotu
y
During playback, press REPEAT (h) repeatedly to
select a desired repeat mode.
Blu-ray Disc / DVD / Movie files
jA- – Selected portion will be repeated continually.
jChapter – The current chapter will be played
back repeatedly.
jTitle – The current title will be played back
repeatedly.
jAll – All the tracks or files will be played back
repeatedly.
To return to normal playback, press REPEAT (h)
repeatedly to select [Off ].
Audio CDs/Music files
Last Scene Memory
er
This unit memorizes the last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
,,Note
yy Last Scene Memory function for a previous
disc is erased once a different disc is played.
yy This function may not work depending on
the disc.
yy On BD-ROM discs with BD-J, the last scene
memory function does not work.
yy This unit does not memorize settings of
a disc if you switch off the unit before
commencing to play it.
;Track– The current track or file will be played
back repeatedly.
:All – All the tracks or files will be played back
repeatedly.
l – The tracks or files will be played back in
random order.
l:All – All the tracks or files will be played
back repeatedly in random order.
kA-B – Selected portion will be repeated
continually. (Audio CD only)
To return to normal playback, press CLEAR.
,,Note
yy If you press V once during Repeat
Chapter/Track playback, the repeat playback
cancels.
yy This function may not work on some disc or
title.
Operating 35
Repeating a specific portion
eroty
Changing content list view
yui
This player can repeat a portion you have selected.
On the [Movie], [Music] or [Photo] menu, you can
change the content list view.
1. While playback, press REPEAT (h) to select
[A-] at the beginning of the portion you wish to
repeat.
2.Press ENTER (b) at the end of the portion. Your
selected portion will be repeated continually.
Method 1
Press red (R) colored button repeatedly.
3. To return to normal playback, press REPEAT
(h) repeatedly to select [Off ].
,,Note
yy You cannot select a portion less than 3
seconds.
yy This function may not work on some disc or
title.
Viewing content information
y
4
Operating
The player can display the content information.
1. Select a file using W/S/A/D.
2. Press INFO/MENU (m) to display the option
menu.
3. Select the [Information] option using W/S,
and press ENTER (b).
The file information appears on the screen.
While movie playback, you can display the file
information by pressing TITLE/POPUP.
,,Note
The information displayed on the screen
may not correct comparing actual content
information.
Method 2
1. On the content list, press INFO/MENU (m) to
display the option menu.
2.Use W/S to select the [View Change] option.
3.Press ENTER (b) to change the content list
view.
36 Operating
Selecting a subtitle file
y
Options while viewing a photo
i
If the subtitle file name is different from the movie
file name, you need to select the subtitle file on the
[Movie] menu before playing the movie.
You can use various options during viewing a
photo in full screen.
1.Use W/S/A/D to select the subtitle file you
wish to play in the [Movie] menu.
2.Press ENTER (b).
4
Operating
Press ENTER (b) again to deselect the subtitle
file. Selected subtitle file will be displayed when
you play the movie file.
,,Note
If you press Z (STOP) while playback, the
subtitle selection is cancelled.
1. While viewing a photo in full screen, press INFO/
MENU (m) to display the option menu.
2. Select an option using W/S.
a Current photo/Total number of photos
– Use A/D to view previous/next photo.
b Slide Show – Press ENTER (b) to start or
pause slide show.
c Music Select – Select the background
music for the slide show (page 37).
d Music –Press ENTER (b) to start or pause
background music.
Changing the mode
yui
On the [Movie], [Music] or [Photo] menu, you can
change the mode.
Press yellow (Y) button repeatedly, the mode is
changed. (Movie : Photo : Music : Movie)
,,Note
If you press Green (G) button on the [Movie],
[Music] or [Photo] menu, the related device list
will appear on the screen.
e Rotate – Press ENTER (b) to rotate the
photo clockwise.
f Zoom – Press ENTER (b) to display the
[Zoom] menu.
g Effect – Use A/D to select a transition
effect between photos in a slide show.
h Speed – Use A/D to select a delaying
speed between photos in a slide show.
3. Press BACK ( ) to exit the option menu.
Operating 37
Listening to music while slide
show
i
You can display photo files while listening to music
files.
1. While viewing a photo in full screen, press INFO/
MENU (m) to display the option menu.
2.Use W/S to select [Music Select] option, and
press ENTER (b) to display the [Music Select]
menu.
3.Use W/S to select a device, and press ENTER
(b).
4.Use W/S to select a file or a folder you wish to
play.
4
5.Use D to select [OK], and press ENTER (b) to
complete music selection.
Operating
Select g and press ENTER (b) to display the
upper directory.
38 Operating
On-Screen display
2. Select an option using W/S.
You can display and adjust various information and
settings about the content.
4. Press BACK ( ) to exit the On-Screen display.
Displaying content information
on-screen
eroy
1. While playback, press INFO/MENU (m) to show
various playback information.
4
Operating
a Title – current title number/total number of
titles
b Chapter – current chapter number/total
number of chapters
c Time – elapsed playing time/total playback
time
d Audio – selected audio language or channel
e Subtitle – selected subtitle.
f Angle – selected angle/total number of
angles
g TV Aspect Ratio – selected TV aspect Ratio
h Picture Mode – selected picture mode
3.Use A/D to adjust the selected option value.
,,Note
yy If no button is pressed for a few seconds,
the on-screen display disappears.
yy A title number cannot be selected on some
discs.
yy Available items may differ depending on
discs or titles.
yy If an interactive Blu-ray Disc is playing back,
some setting information is displayed on
the screen but prohibited to be changed.
Operating 39
Playing from selected time
eroy
Hearing a different audio
eroy
1. Press INFO/MENU (m) during playback. The
time search box shows the elapsed playing
time.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2. Select the [Time] option and then input the
required start time in hours, minutes, and
seconds from left to right.
3.Use A/D to select desired audio language,
audio track or audio channel.
For example, to find a scene at 2 hours, 10
minutes, and 20 seconds, enter “21020”.
Press A/D to skip the playback 60 seconds
forward or backward.
3.Press ENTER (b) to start playback from selected
time.
,,Note
This function may not work on some disc or
titles.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2.Use W/S to select the [Subtitle] option.
3.Use A/D to select desired subtitle language.
4. Press BACK ( ) to exit the On-Screen display.
,,Note
yy Some discs allow you to change subtitle
selections only via the disc menu. If this is
the case, press TITLE/POPUP or DISC MENU
button and choose the appropriate subtitle
from the selections on the disc menu.
yy You can select the [Subtitle] option on the
On-Screen display directely by pressing
SUBTITLE button.
,,Note
yy Some discs allow you to change audio
selections only via the disc menu. In this
case, press TITLE/POPUP or DISC MENU
button and choose the appropriate audio
from the selections on the disc menu.
yy Immediately after you have switched sound,
there may be a temporary discrepancy
between the display and actual sound.
yy On BD-ROM disc, the multi audio format
(5.1CH or 7.1CH) is displayed with [MultiCH]
in the on-screen display.
yy You can select the [Audio] option on the
On-Screen display directely by pressing
AUDIO button.
Watching from a different
angle
er
If the disc contains scenes recorded at different
camera angles, you can change to a different
camera angle during playback.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2.Use W/S to select the [Angle] option.
3.Use A/D to select desired angle.
4. Press BACK ( ) to exit the On-Screen display.
4
Operating
Selecting a subtitle language
eroy
2.Use W/S to select the [Audio] option.
40 Operating
Changing the TV Aspect Ratio
eoy
Changing the Picture Mode
eroy
You can change the TV aspect ratio setting while
playback.
You can change the [Picture mode] option while
playback.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2.Use W/S to select the [TV Aspect Ratio]
option.
2.Use W/S to select the [Picture Mode] option.
3.Use A/D to select desired option.
4. Press BACK ( ) to exit the On-Screen display.
4. Press BACK ( ) to exit the On-Screen display.
,,Note
Even if you change the value of the [TV Aspect
Ratio] option in On-Screen display, the [TV
Aspect Ratio] option in the [Setup] menu is not
changed.
4
3.Use A/D to select desired option.
Setting the [User] option
1. During playback, press INFO/MENU (m) to
display the On-Screen display.
2.Use W/S to select the [Picture Mode] option.
3.Use A/D to select the [User setting] option,
and press ENTER (b).
Operating
Changing subtitle code page
y
If the subtitle is displayed in broken letter, you can
change the subtitle code page to view the subtitle
file properly.
1. During playback, press INFO/MENU (m) to
display the playback menu.
2.Use W/S to select the [Code Page] option.
3.Use A/D to select desired code option.
4.Use W/S/A/D to adjust the [Picture Mode]
options.
Select [Default] option then press ENTER (b) to
reset the all video adjustments.
5.Use W/S/A/D to select the [Close] option,
and press ENTER (b) to finish setting.
4. Press BACK ( ) to exit the On-Screen display.
Operating
Audio CD Recording
You can record one desired track or all of the tracks
in Audio CD to a USB storage device.
41
Enter a folder name using virtual keyboard, and
press ENTER (b) while [OK] is selected.
8.Use W/S/A/D to select [OK], and press
ENTER (b) to start Audio CD recording.
1. Insert a USB storage device to the USB port on
the front panel.
If you want to stop in progressing Audio CD
recording, press ENTER (b) while [Cancel] is
highlighted.
2.Press B (OPEN/CLOSE), and place an Audio CD
on the disc tray.
Press B (OPEN/CLOSE) to close the disc tray.
9. A message appears when Audio CD recording is
completed. Press ENTER (b) to check the audio
file created in the destination folder.
The playback starts automatically.
3. Press INFO/MENU (m) to display the option
menu.
Or
Press X REC button on the remote control.
You can record all musics in the audio CD.
4.Use W/S to select [CD Recording] option, and
press ENTER (b).
5.Use W/S to select a track you wish to copy on
the menu, and press ENTER (b).
Selects all the tracks on an
Audio CD.
Selects an encoding option
from the pop-up menu
(128kbps, 192kbps or 320kbps).
Cancels the recording and
returns to the previous screen.
6.Use W/S/A/D to select [Start], and press
ENTER (b).
7.Use W/S/A/D to select a destination folder
to be copied.
If you want to create a new folder, use
W/S/A/D to select [New Folder] and press
ENTER (b).
stop mode
while playback
1 min.
4 min.
yy Recording times in the table above are
approximate.
yy Actual recording time for USB storage
device varies depending on the USB storage
device’s ability.
yy Make sure that there is minimum of 50 MB
free space is needed when recording into
the USB storage device.
yy The length of the audio should be longer
than 20 seconds for the proper recording.
yy Do not turn off this player or extract the
connected USB storage device during Audio
CD recording.
>>Caution
The recording or copying features on this
player are provided for your personal and noncommercial use. The making of unauthorized
copies of copy-protected material, including
computer programs, files, broadcasts and
sound recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for
such purposes. LG expressly disclaims any
responsibility for illegal distribution or use of
unauthorized content in commercial purpose.
Be Responsible
Respect Copyrights
4
Operating
Repeat this step to select tracks as many as you
can.
,,Note
yy The table below shows the average
recording time from an music track with 4
minutes of playback time to a audio file with
192 kbps as an example.
42 Operating
Radio Operations
Be sure that the antennas are connected.
(Refer to the page 21)
Listening to the radio
1. Press FUNCTION until TUNER (FM) appears in
the display window. The last received station is
tuned in.
4
Deleting a saved station
1. Press PRESET (- / +) to select a preset number
you want to delete.
2. Press CLEAR, the preset number will blink in the
display window.
3. Press CLEAR again, to delete the selected preset
number.
Deleting all the saved stations
2. Press and hold TUNING (-/+) for about two
seconds until the frequency indication starts to
change. Scanning stops when the unit tunes in
a station. Or Press TUNING (-/+) repeatedly.
Press and hold CLEAR for two seconds.
“ERASE ALL” will flash up. Press CLEAR again. Then all
the saved stations are deleted.
3. Adjust the volume by rotating VOLUME on
the front panel or by pressing VOL (+/-) on the
remote control.
Improving poor FM reception
Presetting the Radio Stations
Operating
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
1. Press FUNCTION until the TUNER (FM) appears
in the display window.
2. Select the desired frequency by using TUNING
(-/+).
3. Press ENTER (b) a preset number will flash in
the display window.
4. Press PRESET (-/+) to select the preset number
you want.
5. Press ENTER (b). The station is stored.
6. Repeat the steps 2 to 5 to store other stations.
Press B (blue) (MONO/STEREO) colored button on
the remote control. This will change the tuner from
stereo to mono and usually improve the reception.
Troubleshooting 43
Troubleshooting
General
Symptom
Cause & Solution
The Power does not turned on.
yy Plug the power cord into the wall outlet securely.
The unit does not start
playback.
yy Insert a playable disc. (Check the disc type, color system, and regional
code.)
yy Insert the disc with the playback side down.
yy Clean the disc.
yy Cancel the Rating function or change the rating level.
The angle cannot be changed.
yy Multi-angles are not recorded on the DVD Video being played.
Cannot play movie, photo or
music files.
yy The files are not recorded in a format that the unit can play.
The remote control does not
work properly.
yy The remote control is not pointed at the remote sensor of the unit.
yy The unit does not support the codec of the movie file.
yy The remote control is too far from the unit.
yy There is an obstacle in the path of the remote control and the unit.
yy The batteries in the remote control are exhausted.
The unit is not operating
normally.
You can reset the unit as follows.
yy Unplug the power cord, wait at least five seconds, and then plug it in
again.
5
Troubleshooting
The unit is plugged in, but the
power will not turn on or off.
44 Troubleshooting
Picture
Symptom
Cause & Solution
There is no picture.
yy Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
yy Connect the video connection securely.
yy Check the [HDMI Color Setting] in the [Setup] menu is set to the
appropriate item that conforms to your video connection.
yy Your TV may not support the resolution you have set on the player.
Change the resolution that your TV accepts.
yy The player’s HDMI OUT jack is connected to a DVI device that does
not support copyright protection.
Picture noise appears
yy You are playing a disc recorded in a colour system that is different
from your TV.
yy Set the resolution which your TV accepts.
Sound
Symptom
Cause & Solution
There is no sound or the sound
is distorted.
yy The unit is in scan, slow motion, or pause mode.
5
yy The sound volume is low.
yy Check the speaker cable connection. (page 17)
Troubleshooting
Customer Support
You can update the Player using the latest software to enhance the products operation and/or add new
features. To obtain the latest software for this player (if updates have been made), please visit
http://www.lg.com/global/support or contact LG Electronics customer care centre.
Open source software notice
To obtain the corresponding source code under GPL, LGPL, MPL and other open source licenses, please
visit http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are
available to download with the source code.
Appendix 45
Controlling a TV with
the Supplied Remote
Control
You can control your TV using the buttons below.
Setting up the remote to
control your TV
You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.
1. While holding down 1 (TV POWER) button, and
press the manufacturer code for your TV with
the numerical buttons (see the table below).
Manufacturer
Code Number
LG
1(Default), 2
Zenith
1, 3, 4
GoldStar
1, 2
By pressing
You can
Samsung
6, 7
1 (TV POWER)
Turn the TV on or off.
Sony
8, 9
Switch the TV’s input source
between the TV and other
input sources.
Hitachi
4
AV/INPUT
PR/CH W/S
Scan up or down through
memorized channels.
VOL +/–
Adjust the volume of the TV.
MUTE
Turn the TV’s volume on or
off.
,,Note
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may
be reset to the default setting. Set the appropriate
code number again.
6
Appendix
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
2. Release the 1 (TV POWER) button to complete
setting.
46 Appendix
Area Code List
Choose an area code from this list.
AreaCode AreaCode AreaCode AreaCode
Afghanistan AF Fiji FJ Monaco MC Singapore SG
Argentina AR Finland FI Mongolia MN Slovak Republic SK
Australia AU France FR Morocco MA Slovenia SI
Austria AT Germany DE Nepal NP South Africa ZA
Belgium BE Great Britain GB Netherlands NL South Korea KR
Bhutan BT Greece GR Antilles AN Spain ES
Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK
Brazil BR Hong Kong HK Nigeria NG Sweden SE
Cambodia KH Hungary HU Norway NO Switzerland CH
Canada CA India IN Oman OM Taiwan TW
Chile CL Indonesia ID Pakistan PK Thailand China CN Israel IL Panama PA Turkey TR
Colombia CO Italy IT Paraguay PY Uganda UG
Congo CG Jamaica JM Philippines PH Ukraine UA
Costa Rica CR Japan JP Poland PL United States US
Croatia HR Kenya KE Portugal PT Uruguay UY
Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ
Denmark DK Libya Ecuador EC Luxembourg LY Russian
LU Federation Egypt EG Malaysia 6
El Salvador SV Maldives MY Saudi Arabia MV Senegal Appendix
Ethiopia ET Mexico MX
Vietnam RU Zimbabwe SA
SN
TH
VN
ZW
Appendix 47
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
LanguageCode
LanguageCode
LanguageCode
Afar 6565
French 7082
Lithuanian 7684
Sindhi 8368
Afrikaans 6570
Frisian 7089
Macedonian 7775
Singhalese 8373
Albanian 8381
Galician 7176
Malagasy 7771
Slovak 8375
Amharic 6577
Georgian 7565
Malay 7783
Slovenian 8376
Arabic 6582
German 6869
Malayalam 7776
Spanish 6983
Armenian 7289
Greek 6976
Maori 7773
Sudanese 8385
Assamese 6583
Greenlandic 7576
Marathi 7782
Swahili 8387
Aymara 6588
Guarani 7178
Moldavian 7779
Swedish 8386
Azerbaijani 6590
Gujarati 7185
Mongolian 7778
Tagalog 8476
Bashkir 6665
Hausa 7265
Nauru7865
Tajik 8471
Basque 6985
Hebrew 7387
Nepali 7869
Tamil 8465
Bengali; Bangla 6678
Hindi 7273
Norwegian 7879
Telugu 8469
Bhutani 6890
Hungarian 7285
Oriya 7982
Thai 8472
Bihari 6672
Icelandic 7383
Panjabi 8065
Tonga 8479
Breton 6682
Indonesian 7378
Pashto, Pushto 8083
Turkish 8482
Bulgarian 6671
Interlingua 7365
Persian 7065
Turkmen 8475
Burmese 7789
Irish 7165
Polish 8076
Twi 8487
Byelorussian 6669
Italian 7384
Portuguese 8084
Ukrainian 8575
Chinese 9072
Japanese 7465
Quechua 8185
Urdu 8582
Croatian 7282
Kannada 7578
Rhaeto-Romance 8277
Uzbek 8590
Czech 6783
Kashmiri 7583
Rumanian 8279
Vietnamese 8673
Danish 6865
Kazakh 7575
Russian 8285
Volapük 8679
Dutch 7876
Kirghiz 7589
Samoan 8377
Welsh 6789
English 6978 Korean 7579
Sanskrit 8365
Wolof 8779
6979
Kurdish 7585
Scots Gaelic 7168
Xhosa 8872
Estonian 6984
Laotian 7679
Serbian 8382
Yiddish 7473
Faroese 7079
Latin 7665
Serbo-Croatian 8372
Yoruba 8979
Fiji 7074
Latvian, Lettish 7686
Shona 8378
Zulu 9085
Finnish 7073
Lingala 7678
Esperanto 6
Appendix
LanguageCode
48 Appendix
Trademarks and
Licenses
Blu-ray Disc™, Blu-ray™, BONUSVIEW™ and
the logos are trademarks of the Blu-ray Disc
Association.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
Java is a trademark of Oracle and/or its affiliates.
6
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
Appendix
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535;
7,392,195; 7,272,567; 7,333,929; 7,212,872 & other
U.S. and worldwide patents issued & pending.
DTS-HD, the Symbol, & DTS-HD and the Symbol
together are registered trademarks & DTS-HD
Master Audio | Essential is a trademark of DTS,
Inc. Product includes software. © DTS, Inc. All
Rights Reserved.
“AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries
and are used under license.
Appendix 49
Cinavia Notice
This product uses Cinavia technology to limit the
use of unauthorized copies of some commerciallyproduced film and videos and their soundtracks.
When a prohibited use of an unauthorized copy is
detected, a message will be displayed and playback
or copying will be interrupted.
More information about Cinavia technology
is provided at the Cinavia Online Consumer
Information Center at http://www.cinavia.com. To
request additional information about Cinavia by
mail, send a postcard with your mailing address
to: Cinavia Consumer Information Center, P.O. Box
86851, San Diego, CA, 92138, USA.
This product incorporates proprietary technology
under license from Verance Corporation and is
protected by U.S. Patent 7,369,677 and other U.S.
and worldwide patents issued and pending as well
as copyright and trade secret protection for certain
aspects of such technology. Cinavia is a trademark
of Verance Corporation. Copyright 2004-2010
Verance Corporation. All rights reserved by Verance.
Reverse engineering or disassembly is prohibited.
6
Appendix
50 Appendix
Audio Output Specifications
Jack/Setting
Source
HDMI OUT
PCM Stereo
PCM Multi-Ch
DTS Re-encode *3
Bit Stream *1 *2
Dolby Digital
PCM 2ch
PCM 5.1ch
DTS
Dolby Digital
Dolby Digital Plus
PCM 2ch
PCM 5.1ch
DTS
Dolby Digital Plus
Dolby TrueHD
PCM 2ch
PCM 5.1ch
DTS
Dolby TrueHD
DTS
PCM 2ch
PCM 5.1ch
DTS
DTS
DTS-HD
PCM 2ch
PCM 5.1ch
DTS
DTS-HD
Linear PCM 2ch
PCM 2ch
PCM 2ch
DTS
Linear PCM 2ch
Linear PCM 5.1ch
PCM 2ch
PCM 5.1ch
DTS
Linear PCM 5.1ch
Linear PCM 7.1ch
PCM 2ch
PCM 5.1ch
DTS
Linear PCM 7.1ch
*1 The secondary and interactive audio may not
be included in the output bitstream if [Digital
Output] option is set to [Bit Stream]. (Except
LPCM Codec : the output always include
interactive and secondary audio.)
*2 This player automatically selects the HDMI audio
according to the decoding capability of the
connected HDMI device even though [Digital
Output] option is set to [Bit Stream].
6
Appendix
*3 If the [Digital Output] option is set to [DTS reencode], the audio output is limited to 48 kHz
and 5.1Ch. If the [Digital Output] option is set
to [DTS re-encode], the DTS Re-encode audio
is outputted for BD-ROM discs, and the original
audio is outputted for the other discs (like [Bit
Stream]).
yy The audio is outputted as PCM 48 kHz/16 bit for
MP3/WMA file and PCM 44.1kHz/16 bit for Audio
CD while playback.
yy With digital audio connection (HDMI OUT), Disc
Menu button sounds of BD-ROM may not be
heard if the [Digital Output] option is set to [Bit
Stream].
yy If the audio format of the digital output does
not match the capabilities of your receiver, the
receiver will produce a strong, distorted sound
or no sound at all.
yy Multi-channel Digital Surround Sound via digital
connection can only be obtained if your receiver
is equipped with a Digital Multi-channel decoder.
yy This setting is not available on the input signal
from an external device.
Appendix
51
Specifications
General
Power requirements
Refer to main label.
Power consumption
Refer to main label.
Dimensions (W x H x D)
Approx. 360 x 60.5 x 304 mm
Net Weight (Approx.)
2.5 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Inputs/Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector)
ANALOG AUDIO IN
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
PORT. IN
0.5 Vrms (3.5 mm stereo jack)
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
Power output, (RMS), THD 10 %
330 W
Front
42 W x 2
Center
42 W
Rear
42 W x 2
Sub-Woofer
120 W (Passive)
6
Appendix
Total
52 Appendix
System
Laser
Semiconductor laser
Wavelength
405 nm / 650 nm
Signal system
Standard PAL/NTSC color TV system
Frequency response
20 Hz to 18 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Harmonic distortion
Less than 0.05 %
Dynamic range
More than 80 dB
Bus Power Supply (USB)
DC 5 V 0 500 mA
Speakers
Front speaker (Left/ Right)
Type
1 Way 1 speaker
Max. Input power
84 W
Impedance Rated
3Ω
Net Dimensions
(W x H x D)
92.5 x 115 x 79 mm
Input Power
42 W
Net Weight
0.39 kg
Rear speaker (Left/ Right)
Type
1 Way 1 speaker
Max. Input power
84 W
Impedance Rated
3Ω
Net Dimensions
(W x H x D)
92.5 x 115 x 79 mm
Input Power
42 W
Net Weight
0.39 kg
1 Way 1 Speaker
Max. Input power
84 W
Impedance Rated
3Ω
Net Dimensions
(W x H x D)
92.5 x 115 x 79 mm
Input Power
42 W
Net Weight
0.39 kg
1 Way 1 speaker
Max. Input power
240 W
Impedance Rated
4Ω
Net Dimensions
(W x H x D)
156 x 325 x 267 mm
Input Power
120 W
Net Weight
3.6 kg
Center speaker
Type
6
Subwoofer
Appendix
Type
yy Design and specifications are subject to change without notice.
Appendix 53
Maintenance
Notes on Discs
Handling Discs
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
yy Do not use volatile liquids such as insecticide
spray near the unit.
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Maintaining the Unit
6
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
Download PDF

advertising