OWNER’S MANUAL DVD Micro Hi-Fi System Please read this manual carefully before operating your set and retain it for future reference. FB165 (FB165, FBS166V) 2 Getting Started Safety Information 1 CAUTION Getting Started RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible. Getting Started This device is equipped with a portable battery or accumulator. CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus. Copyrights It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs picture noise will appear. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players. (Mastered/ Live File System : Disc format system for Windows Vista) The appliance is not intended for use by young children or infirm persons without supervision. Young Children should be supervised to ensure that they do not play with appliance. If the appliance is supplied from a cord extension set or an electrical portable outlet device, the cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture. 1 Getting Started Safety way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. 3 4 Table of Contents Table of Contents 1 Getting Started 2 6 6 6 6 6 7 7 7 7 7 8 9 10 12 Safety Information Unique Features – Portable In – USB Direct Recording – Full HD up-scaling Accessories Introduction – Playable Discs – About the “7” Symbol Display – Symbols Used in this Manual – Regional Codes Playable file Requirement Remote control Front panel Rear panel 2 Connecting 13 13 14 14 15 16 16 16 16 16 Attaching the speakers to the unit Connections to Your TV – Component Video Connection – HDMI Out Connection – Video Connection – Resolution Setting Video Output Resolution Optional Equipment Connection – AUDIO (PORT. IN) In Connection – Listening to music from your portable player or external device – USB Connection – OPTICAL In connection – Home theater speaker ez setup – Antenna Connection – Playing the iPod – Compatible iPod 17 17 17 18 18 19 3 System Setting 20 20 Adjust the setup settings – OSD Initial language settings Optional – To display and exit the Setup menu – Language – Display – Audio – Lock (Parental Control) – Others 20 21 21 22 22 23 Table of Contents 4 Operating 5 Troubleshooting 24 24 25 25 25 25 25 25 25 26 26 26 27 28 28 28 29 29 29 29 29 29 30 30 30 30 30 30 31 31 32 32 Using the Home Menu Basic Operations Other Operations – Displaying Disc Information on-screen – To display the DVD Menu – To xdisplay the DVD title – 1.5 times speed playback – Screen Saver – Starting play from selected time – Resume playback – Changing subtitle code page – Marked Playback – Viewing a PHOTO file – Last Scene Memory – System Select - Optional – Adjust the speaker level settings – Setting the Clock – Using your player as an alarm clock – Sleep Timer Setting – Dimmer – Turn off the sound temporarily – DEMO Radio Operations – Listening to the radio – Presetting the Radio Stations – Deleting all the saved stations – Deleting a saved station – Improving poor FM reception Sound adjustment – Setting the surround mode Advanced Operations – Recording to USB. 33 Troubleshooting 6 Appendix 34 35 36 37 39 39 39 Area Code List Language code List Trademarks and Licenses Specifications Maintenance – Handling the Unit – Notes on Discs 5 1 2 3 4 5 6 6 Getting Started Unique Features Accessories Please check and identify the supplied accessories. 1 Portable In Getting Started Listens to music from your portable device. (MP3, Notebook, etc) USB Direct Recording Records music from CD to your USB device. Remote control (1) Battery (1) FM antenna (1) Video cable (1) Full HD up-scaling Views Full HD picture quality with simple setup. Getting Started Introduction Playable Discs DVD-VIDEO (8 cm / 12 cm disc) Discs such as movies that can be purchased or rented. DVD±R (8 cm / 12 cm disc) Video mode and finalized only. Symbols Used in this Manual r DVD-Video, DVD±R/RW in Video mode or VR mode and finalized t Audio CDs y Video files contained in the USB/Disc u Audio files contained in the USB/Disc i Photo files , Note Indicates special notes and operating features. , Tip Indicates tip and hints for making the task easier. DVD-RW (8 cm / 12 cm disc) Video mode and finalized only. DVD+R: Video mode only > Caution Indicates cautions for preventing possible damages from abuse. Supports the double layer disc also. DVD+RW (8 cm / 12 cm disc) Video mode and finalized only. Audio CD: Music CDs or CD-R/CDRW in music CD format that can be purchased. About the “7” Symbol Display “7” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media. Regional Codes This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or “ALL”. Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your unit’s regional code or the disc cannot play. If you try to play a DVD with a different regional code from your unit, the message “Check Regional Code” appears on the TV screen. 1 Getting Started This unit plays DVD±R/RW and CD-R/RW that contains audio titles, DivX, MP3, WMA and/or JPEG files. Some DVD±RW/DVD±R or CD-RW/ CD-R cannot be played on this unit due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. 7 8 Getting Started Playable file Requirement DivX file requirement DivX file compatibility with this unit is limited as follows: Available resolution: within 800 x 600 (W x H) pixels. 1 Getting Started MP3/ WMA music file requirement MP3/ WMA file compatibility with this unit is limited as follows : Sampling frequency : within 32 to 48 kHz (MP3), within 32 to 48 kHz (WMA) Bit rate : within 32 to 320 kbps (MP3), 40 to 192 kbps (WMA) Support Version : v2, v7, v8, v9 Maximum files : Under 999 File extensions : “.mp3”/ “.wma” The file name of the DivX subtitle should be entered within 45 characters. If there is impossible code to express in the DivX file, it may be displayed as “ _ “ mark on the display. Frame rate : less than 30 fps. If the video and audio structure of recorded files is not interleaved, either video or audio is outputted. Playable DivX file : “.avi”, “.mpg”, “.mpeg”, “.divx” We recommend that you use Easy-CD Creator, which creates an ISO 9660 file system. Playable Subtitle format : SubRip (*.srt/ *.txt), SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt), MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/ *.txt), Vobsub (*.sub) Photo file requirement Playable Codec format : “DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”, “MP4V3”, “3IVX”. CD-ROM file format : ISO9660/ JOLIET Photo file compatibility with this unit is limited as follows : Max pixel in width : 2 760 x 2 048 pixel Maximum files : Under 999 Some discs may not operate due to a different recording format or the condition of disc. File extensions: “.jpg” CD-ROM file format : ISO9660/ JOLIET Playable Audio format : “AC3”, “PCM”, “MP3”, “WMA”. Sampling frequency : within 32 to 48 kHz (MP3), within 32 to 48 kHz (WMA) Bit rate : within 32 to 320 kbps (MP3), 40 to 192 kbps (WMA) For Discs formatted in Live file system, you can not it on this unit. If the name of movie file is different from that of the subtitle file, during playback of a DivX file, subtitle may not be display. If you play a DivX file differ from DivXspec, it may not operate normally. Getting Started Remote control • • • • • • a • • • • • • • • • • • d • • • • • P RADIO&INPUT: Changes input sources. SPEAKER LEVEL: Sets the sound level of desired speaker. MARKER: Marks play list. SOUND EFFECT: Selects a sound effect mode. B OPEN/CLOSE: Ejects or insert the disc from slot loader. SLEEP: Sets the System to turn off automatically at a specified time. (Dimmer : The display window will be darken by half.) OPTICAL: Changes input source to optical directly. MUTE: Mutes the sound. • • • • • • e • • • • • m INFO/DISPLAY: Accesses OnScreen Display. 0-9 numerical buttons: Selects numbered options in a menu. n HOME: Displays the [Home Menu]. CLEAR: Removes a number when setting the password. DISC MENU: Accesses the menu on a DVD disc. REPEAT: Selects a play mode. (Repeat/ Random) • • • • • • b • • • • • • • • • • • f • • • • • W/S/A/D (up/ down/ left/ right): Used to navigate on-screen displays. TV Control buttons: Controls the TV. (LG TV only) PRESET +/-: Selects programme of Radio. TUNING -/+: Tunes in the desired radio station. b ENTER: Acknowledges menu selection. Presetting the radio stations. x RETURN: Moves backwards in the menu or exits the setup menu. TITLE: If the current DVD title has a menu, the title menu appears on the screen. Otherwise, the disc menu may not appear. • • • • • • c • • • • • C/V SKIP: Goes to the next or previous chapter / track / file. c/v SCAN: Searches backward or forward. Remove the battery cover on the rear of the Remote Control, and insert one (size AAA) battery with 4 and 5 matched correctly. VOL +/- (Volume): Adjusts speaker volume. Z STOP: Stops playback. d PLAY, MONO/STEREO: Starts playback. Selects Mono/ Stereo. M PAUSE/STEP: Pauses playback. - You can control the sound lev el, input source, and power switching of LG TVs as well. Hold POWER (TV) and press PR/ CH (+/-) button repeatedly until the TV turns on or off. X REC: USB Direct Recording. ?: This button is not available. 1 Getting Started 1 POWER: Switches the unit ON or OFF. Battery Installation 9 10 Getting Started Front panel 1 Getting Started Getting Started a Disc Slot b iPod dock c 1/! (POWER) Switches the unit ON or OFF. e FUNC. (FUNCTION) Changes the input source or function. f USB Port Connects an USB device. g EQ You can choose fixed sound impression. SET/ DEMO Confirms the setting./ Press DEMO in power off state to demonstrate the function on display window. To cancel it, press DEMO again. TIMER With the TIMER function you can turn USB, CD play and TUNER reception on or off at a desired time. CLOCK For setting the clock and checking the time. h B (OPEN/CLOSE) Ejects or insert the disc from slot loader. i C/V (Skip/Search): Goes to next or previous file/track/chapter. Searches backward or forward (Press and hold) Tunes in the desired radio station. d/M (PLAY / PAUSE) Starts playback. Pauses playback temporarily, press again to exit pause mode. j -/+ (VOLUME) Adjusts speaker volume. Z (STOP) Stops playback. k USB REC. Recoding to USB. l PORT. IN Connects to a portable player with audio outputs. PHONES Headphone jack 1 Getting Started d Display window Shows the current status of the unit. 11 12 Getting Started Rear panel 1 Getting Started a OPTICAL IN Connects to optical audio equipment. b HDMI OUT Connects to TV with HDMI inputs. (Interface for digital audio and video) c Antenna Connector FM- Connects the FM wired antenna d VIDEO OUT Connects to a TV with video inputs. e COMPONENT VIDEO (Y PB PR)OUTPUT (PROGRESSIVE SCAN) Connects to a TV with Y PB PR inputs. f Speakers connectors Connects the speaker cables. g Cooling Fan h Power cord Connecting 13 Attaching the speakers to the unit Connections to Your TV To connect the cable to the unit, press each plastic finger pad to open the connection terminals on the unit. Insert the wire and release the finger pad. Make one of the following connections, depending on the capabilities of your existing equipment. Connect the black stripe of each wire to the terminals marked - (minus) and the other end to the terminals marked + (plus). , Note Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections. > Caution Make sure the unit is connected directly to the TV. Tune the TV to the correct video input channel > Caution The speakers contain magnet parts, so color irregularity may occur on the TV screen or PC monitor screen. Please use the speakers far away from either TV screen or PC monitor. Make sure to install the speaker with other people in order to prevent it from falling and causing injuries to the installer. Do not connect your player via your VCR. The image could be distorted by the copy protection system. 2 Connecting Depending on your TV and other equipment you wish to connect, there are various ways you could connect the player. Use only one of the connections described in this manual. 14 Connecting Component Video Connection HDMI Out Connection Connect the COMPONENT VIDEO OUTPUT (PROGRESSIVE SCAN) jacks on the unit to the corresponding input jacks on the TV using component cables. If you have a HDMI TV or monitor, you can connect it to this unit using a HDMI cable (Type A, High Speed HDMI™ cable). Connect the HDMI OUT jack on the unit to the HDMI IN jack on a HDMI compatible TV or monitor. Set the TV’s source to HDMI (refer to TV’s Owner’s manual). You can hear the sound through the system’s speakers. 2 Connecting Unit Unit TV TV Green Blue Red , Tip You can fully enjoy digital audio and video signals together with this HDMI connection. When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution” on page 16.) Connecting , Note If a connected HDMI device does not accept the audio output of the unit, the HDMI device’s audio sound may be distorted or may not output. Video Connection Connect the VIDEO OUT jack on the unit to the video in jack on the TV using a video cable. You can hear the sound through the system’s speakers. Unit 2 Connecting When you connect a HDMI or DVI compatible device make sure of the following: - Try switching off the HDMI/DVI device and this unit. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this unit. - The connected device’s video input is set correctly for this unit. - The connected device is compatible with 720 x 480i (or 576i), 720 x 480p (or 576p), 1 280 x 720p, 1 920 x 1 080i or 1 920 x 1 080p video input. Not all HDCP-compatible HDMI or DVI devices will work with this unit. - The picture will not be displayed properly with non-HDCP device. - This unit does not playback and TV screen is changed to black or green screen or the snow noise may occur on the screen. If there is noise or lines on the screen, please check the HDMI cable and usea higher version cable than High Speed HDMI™ cable. > Caution Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the unit and then turn it on again. When the HDMI connection with HDCP is not verified, TV screen is changed to black or green screen or the snow noise may occur on the screen. In this case, check the the HDMI connection, or disconnect the HDMI cable. 15 TV Yellow 16 Connecting Resolution Setting The unit provides several output resolutions for HDMI OUT and COMPONENT VIDEO OUT jacks. You can change the resolution using [Setup] menu. 1. Press n HOME. 2. Use A/D to select the [Setup] and press b ENTER. The [Setup] menu appears. Optional Equipment Connection AUDIO (PORT. IN) In Connection Connect an output of portable device (MP3 or PMP etc) to the AUDIO (PORT. IN) input connector. 2 Connecting 3. Use W/S to select [Display] option then press D to move to the second level. 4. Use W/S to select the [Resolution] option then press D to move to the third level. 5. Use W/S to select the desired resolution then press b ENTER to confirm your selection. , Note If your TV does not accept the resolution you have set on the player, you can set resolution to 480p (or 576p) as follows: Press Z STOP for more than 5 seconds. Video Output Resolution Displayed resolution in display window and outputted resolution may different according to connection type. [HDMI OUT]: 1 080p, 1 080i, 720p and 480p (or 576p) and 480i (or 576i) [COMPONENT VIDEO OUT]: 480p (or 576p) and 480i (or 576i) [VIDEO OUT]: 480i (or 576i) MP3 player, etc... Listening to music from your portable player or external device The unit can be used to play the music from many types of portable player or external devices. 1. Connect the portable player to the PORT.IN(PORTABLE IN) connector of the unit. 2. Turn the power on by pressing 1 (POWER). 3. Select the PORTABLE function by pressing P RADIO&INPUT. 4. Turn on the portable player or external device and start it playing. Connecting 17 USB Connection OPTICAL In connection Connect the USB port of USB Memory (or MP3 player, etc.) to the USB port on the front of the unit. Connect an optical output of Unit (or Digital Device etc) to the OPTICAL IN connector. 2 You can only recharge your iPod through USB port. To listen to music on iPod, refer to the page 18. Connecting Removing the USB Device from the unit 1. Choose a different function mode or press Z STOP twice in a row. 2. Remove the USB device from the unit. To the digital optical output jack of your component Compatible USB Devices MP3 Player : Flash type MP3 player. USB Flash Drive : Devices that support USB2.0 or USB1.1. The USB function of this unit does not support some USB devices. USB device requirement Devices which require additional program installation connected to a computer, are not supported. Do not extract the USB device while in operation. For a large capacity USB, it may take longer than a few minute to be searched. To prevent data loss, back up all data. If you use a USB extension cable or USB hub, the USB device is not recognized. Using NTFS file system is not supported. (Only FAT(16/32) file system is supported.) This unit is not supported when the total number of files is 1 000 or more. External HDD, Card readers, Locked devices, or hard type usb devices are not supported. USB port of the unit cannot be connected to PC. The unit can not be used as a storage device. Home theater speaker ez setup Listen to sound from TV, DVD and Digital Device with 5.1(2.1 or 2)ch mode. Even in power off mode, if you press OPTICAL, then power is on and automatically changed to AUX OPT mode. 1. Connect the unit’s OPTICAL IN jack to jack on optical out of your TV (or Digital Device etc.). 2. Select the AUX OPT by using the OPTICAL. To select the AUX OPT directly. 3. Listen sound with 5.1(2.1 or 2)ch speaker. 4. To escape from AUX OPT by using the OPTICAL. Function is retuned to previous one. 18 Connecting Antenna Connection Playing the iPod Connect the supplied FM antenna for listening to the radio. You can enjoy the sound with your iPod. For details about iPod, refer to the iPod User Guide. Connect the FM Wire antenna to the FM antenna connector. 1. Connect the iPod firmly. 2 Connecting If you turn this unit on, your iPod is automatically turned on and recharging starts. 2. Press FUNC. on the unit or P RADIO&INPUT on the remote control to select iPod function. You can operate your iPod through an iPod’s display by using the supplied remote control and also control on your iPod. , Note Be sure to fully extend the FM wire antenna. After connecting the FM wire antenna, keep it as horizontal as possible. Connecting To 19 , Note Do this ON REMOTE Pauses or restart d/M d/M Skip C/V C/V Search Press and hold C/V Press and hold c/v Move to the previous menu - A Move to the desired item - Chooses a item - W/S D Compatible iPod We recommend installing the latest software version. The unit supports the models as follows/ iPod nano 1 G, 2 G, 3 G, 4 G, 5 G, 6 G/ iPod classic/ iPod 4 G, 5 G/ iPod touch 2 G, 3 G, 4 G/ iPhone 3 G, 4. For some models, the unit may not operate depending on the firmware version. Depending on your iPod’s software version, you may not control your iPod from the player. - Your iPod is not connected firmly. - This unit recognizes your iPod as an unknown device. - Your iPod is exceptionally low in power. / The battery needs to be charged. / If you charge the battery while iPod is extremely low in power, it may take longer to be charged. iPod does not support recording function when connected. Depending on your iPod’s software version, it may not be possible to control your iPod from this unit. We recommed installing the latest software version. If you use an application, make a call, or send and receive SMS text message, etc. on iPod touch or iPhone, disconnect it from iPod dock of this unit and then use it. If you have a problem with your iPod, please visit www.apple.com/support/ipod. 2 Connecting ON UNIT If this unit displays an error message, follow the message. An error message “ERROR”. 20 System Setting Adjust the setup settings By using the Setup menu, you can make various adjustments to items such as picture and sound. To display and exit the Setup menu 1. Press n HOME. Displays the [Home Menu]. You can also set a language for the subtitles and the Setup menu, among other things. For details on each Setup menu item, see pages 20 to 23. 2. Select an [Setup] by using A D. OSD Initial language settings - Optional 3 System Setting During the first use of this unit, the initial language setup menu appears on your TV screen. You must complete initial language selection before using the unit. English will be selected as the initial language. 1. Press 1 (POWER) to turn the unit on. The language setup menu will appear on the screen. 3. Press b ENTER. Displays the [Setup]. 4. Press n HOME or x RETURN to exit in the [Setup] Menu. About help menu for Setup Menu Buttons Operation WS Moving to another menu. a Move A Moving to previous level. d Move D Moving to next level or selecting menu. x RETURN To exit the [Setup] menu. b ENTER To confirm menu. ws Move x 2. Use WSAD to select a language then press b ENTER. The confirm menu will appear. 3. Use AD to select the [Enter] then press b ENTER to finish the language setup. Close b Select System Setting 21 Language Display Mode Menu Language The Display Mode setting works only when the TV Aspect mode is set to 4:3. Select a language for the Setup menu and then on screen display. [Letterbox] Disc Audio / Disc Subtitle / Disc Menu [Panscan] Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu. [Original] Refers to the original language in which the disc was recorded. To select another language, press numeric buttons and then b ENTER to enter the corresponding 4-digit number according to the language code list on the page 35. If you enter the wrong language code, press CLEAR. [Off (for Disc Subtitle)] Turn off Subtitle. Display Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit. (If the disc/file is not compatible with Pan Scan, the picture is displayed at Letterbox ratio.) Resolution Sets the output resolution of the Component and HDMI video signal. Refer to “Resolution Setting” for details about the resolution (page 16). [Auto] If the HDMI OUT jack is connected to TVs providing display information (EDID), automatically selects the resolution best suited to the connected TV. If the COMPONENT VIDEO OUT is only connected, this changes the resolution to 480i (or 576i) as default resolution. [1080p] TV Aspect Outputs 1 080 lines of progressive video. Select which screen aspect to use based on the shape of your TV screen. [1080i] [4:3] Select when a standard 4:3 TV is connected. [16:9] Select when a 16:9 wide TV is connected. Outputs 1 080 lines of interlaced video. [720p] Outputs 720 lines of progressive video. [480p (or 576p)] Outputs 480 (or 576) lines of progressive video. [480i (or 576i)] Outputs 480 (or (576) lines of interlaced video. 3 System Setting [Other] Displays a wide picture with bands on the upper and lower portions of the screen. 22 System Setting Audio Lock (Parental Control) DRC (Dynamic Range Control) Initial Setting the Area Code: Make the sound clear when the volume is turned down (Dolby Digital only). Set to [On] for this effect. When you use this unit for the first time, you have to set the Area Code. 1. Select the [Lock] menu and then press D. Vocal Select [On] to mix karaoke channels into normal stereo. This function is effective for multi-channel karaoke DVDs only. 3 HD AV Sync System Setting Sometimes Digital TV encounters a delay between picture and sound. If this happens you can compensate by setting a delay on the sound so that it effectively ‘waits’ for the picture to arrive: this is called HD AV Sync. Use WS (on the remote control) to scroll up and down through the delay amount, which you can set at anything between 0 and 300m sec. 2. Press D. To access the [Lock] options, you must input the password you have created. Input a password and press b ENTER. Enter it again and press b ENTER to verify. If you make a mistake before pressing b ENTER, press CLEAR. 3. Select the first character using W S buttons. 4. Press b ENTER and select the second character using W S buttons. 5. Press b ENTER to confirm your Area code selection. Rating Blocks playback of rated DVDs based on their contents. Not all discs are rated. 1. Select [Rating] on the [Lock] menu then press D. 2. Input a password and press b ENTER. 3. Select a rating from 1 to 8 using the WS buttons. [Rating 1-8] Rating one (1) has the most restrictions and rating eight (8) is the least restrictive. [Unlock] If you select unlock, parental control is not active and the disc plays in full. 4. Press b ENTER to confirm your rating selection. System Setting 23 Password Others You can enter or change password. 1. Select [Password] on the [Lock] menu and then press D. 2. Press b ENTER. 3. Input a password and press b ENTER. To change the password, press b ENTER when the [Change] option is highlighted. Input a password and press b ENTER. Enter it again and press b ENTER to verify. 4. Press n HOME to exit the menu. , Note If you forget your password, you can clear it using the following steps: 2. Input the 6-digit number “210499” and press b ENTER. The password is cleared. Area Code Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 34. 1. Select [Area Code] on the [Lock] menu then press D. 2. Input a password and press b ENTER. 3. Select the first character using W S buttons. 4. Press b ENTER and select the second character using W S buttons. 5. Press b ENTER to confirm your Area code selection. We provide you with the DivX® VOD (Video On Demand) registration code that allows you to rent and purchase videos using the DivX® VOD service. For more information, visit www.divx.com/vod. [Register] Displays the registration code of your player. [Deregister] Deactivate your player and display the deactivation code. , Note All the downloaded videos from DivX VOD can only be played back on this unit. 3 System Setting 1. Select the [Setup] menu on the [Home Menu]. DivX VOD 24 Operating Using the Home Menu 1. Press n HOME. Displays the [Home Menu]. 2. Select an option by using AD. 3. Press b ENTER then selected option menu. [Music] – Displays [MUSIC] menu. [Movie] – Start video media’s playback or displays the [MOVIE] menu. [Photo] – Displays [PHOTO] menu. [Setup] – Displays the [Setup] menu. , Note 4 Operating You can not select the [Music], [Movie] or [Photo] option when the USB device is not connected or a disc is not inserted. Basic Operations To Stop 3. Select an option by using AD. If you select the [Movie], [Photo] or [Music] option when you connect up to two devices, it appears as belows. Select a media then press b ENTER. 4. Press b ENTER then selected option menu. , Note For the most Audio CD and DVD-ROM discs, playback starts automatically. The unit plays only music file contained in the USB storage device or disc automatically. Press Z STOP. Playback Press d PLAY, MONO/ STEREO. Pause Press M PAUSE/STEP. Press M PAUSE/STEP Frame-byrepeatedly to play title FrameFrame playback by-Frame. (DVD, DivX only) During playback, press C/ V SKIP to go to the next Skipping to the chapter/ track/ file or to next/ previous return to the beginning of the chapter/ track/ current chapter/ track/ file. file Press C SKIP twice briefly to step back to the previous chapter/ track/ file. Locating a point quickly by playing a file in fast forward or fast reverse 1. Insert the disc by using the B OPEN/CLOSE or Connect the USB device to the USB port. 2. Press n HOME. Displays the [Home Menu]. Do this Playing repeatedly or randomly During playback, press c/ v SCAN repeatedly to select the required scan speed. To return to normal speed, press d PLAY, MONO/ STEREO. Press REPEAT repeatedly, and the current title, chapter or track will be played back repeatedly or randomly. - DVD : Chapter/ Title/ Off - DivX : Title/ All/ Off - Audio CD/ MP3/ WMA : Track/ All/ Random/ Off Slowing down the playing speed In the pause mode, press SLOW (c or v) to select the required speed. (DVD, DivX only) The DivX file cannot be slow down reverse playback. Operating 25 Other Operations To display the DVD title r Displaying Disc Information on-screen You can display various information about the disc loaded on-screen. 1. Press m INFO/DISPLAY to show various playback information. The displayed items differ depending on the disc type or playing status. 2. You can select an item by pressing WS and change or select the setting by pressing AD. Title – Current title number/ total number of titles. Chapter – Current chapter number/ total number of chapters. When you play a DVD which contains several title, you can select the title you want using the Menu. 1. Press TITLE. The disc’s title appears. 2. Select the menu by pressing WSAD. 3. Press d PLAY, MONO/STEREO to confirm. 1.5 times speed playback r The 1.5 speed allows you to watch the pictures and listen to the sound quicker than playing at a normal speed. Time – Elapsed playing time. 1. During playback, press d PLAY, MONO/ STEREO to play at 1.5 times speed. “dX1.5” appears on the screen. Audio – Selected audio language or channel. 2. Press d PLAY, MONO/STEREO again to exit. Angle – Selected angle/ total number of angles. , Note If any button is not pressed for a few seconds, the on-screen display disappears. To display the DVD Menu r When you play a DVD which contains several menu, you can select the menu you want using the Menu. Screen Saver The screen saver appears when you leave the unit in Stop mode for about five minutes. Starting play from selected time ry To start playing at any chosen time on the file or title. 1. Press m INFO/DISPLAY during playback. 1. Press DISC MENU. The disc’s menu appears. 2. Press WS to select the time clock icon and “--:--:--” appears. 2. Select the menu by using WSAD. 3. Input the required start time in hours, minutes, and seconds from left to right. If you enter the wrong numbers, press CLEAR to remove the numbers you entered. Then input the correct numbers. For example, to find a scene at 1 hour, 10 minutes, and 20 seconds, enter “11020” by using numerical buttons. 3. Press d PLAY, MONO/STEREO to confirm. 4. Press b ENTER to confirm. Playback starts from the selected time. 4 Operating Subtitle – Selected subtitle. 26 Operating Resume playback Marked Playback ryut ut The unit records the point where you pressed the Z STOP depending on the disc. If “MZ (Resume Stop)” appears on the screen briefly, press d PLAY, MONO/STEREO to resume playback (from the scene point). The mark function enables you to store your favourite files from any disc or USB device in the unit memory. If you press Z STOP twice or unload the disc, “Z”(Complete Stop) appears on the screen. The unit will clear the stopped point. , Note The resume point may be cleared when a button is pressed (for example; 1 (POWER), B OPEN/CLOSE, etc). 1. Select [Music] on the [Home Menu]. Returning to the upper folder. (MP3/ WMA only) File information will be displayed according to the ID3TAG information on the appropriate music file. (MP3 only) Changing subtitle code page 4 y Operating If the subtitle is not displayed properly, you can change the subtitle code page to view the subtitle file properly. 1. During playback, press m INFO/DISPLAY to display the On-Screen display. Selecting all tracks/ files. Deselecting all tracks/files. Moving to the previous or next file list. 2. Use WS to select the [Code Page] option. 3. Use AD to select desired code option. 4. Press x RETURN to exit the On-Screen display. 2. Select a desired music on the [List] by using the WS then press MARKER to appears the mark on the list. 3. Press b ENTER or d PLAY, MONO/STEREO. Displays the play mode. 4. Select the play mode by using the WS and press b ENTER. [Mark Play] Marked playback. [Current Play] Normal playback. , Note If you want to select all files on the list, select [Select All] and press b ENTER. Operating 27 To delete a Marker 1. Use WS to select the track that you wish to erase from the marked file. 2. Press MARKER. To delete all Markers Use WSAD to select [Deselect All] then press b ENTER in program edit mode. , Note The markers are also cleared when the disc or USB device is removed, the unit is switched to power off or the function is switched to others. About help menu in the [Photo] menu Menu Buttons Operation d Slide Show d PLAY, MONO/ STEREO wsad Move SWAD Moving to another file or content. b Select b ENTER Viewing a particular file. x Close x RETURN Viewing a slide show. Returning to the [Home Menu]. About help menu in the full screen Viewing a PHOTO file i Menu Buttons Operation Menu m INFO/ DISPLAY Displaying the Option menu. a/d Prev./ Next A/D Moving to another file. This unit can play discs with photo files. x Moving to the previous or next file list. Returning to the upper folder. 2. Press W S to select a folder, and then press b ENTER. 3. If you want to view a slide show, press W S to highlight a file and press d PLAY, MONO/ STEREO. Close x RETURN Returning to the [Photo] menu. 4 Operating 1. Select [Photo] on the [Home Menu] and press b ENTER. 28 Operating Options while viewing a photo System Select - Optional You can use various options during viewing a photo in full screen. You must select the appropriate system mode for your TV system. Press and hold M PAUSE/STEP for more than five seconds to be able to select a system in the [Home Menu]. 1. While viewing a photo in full screen, press m INFO/DISPLAY to display the option menu. , Note 2. Select an option using WSAD. If the USB device is connected or a disc is inserted, this function is not operated. Adjust the speaker level settings a You can adjust the sound level of each speaker. b c d e a Current photo/ Total number of photos – Use AD to view previous/next photo. 4 Operating b Slide Show z/M– Press ENTER to start or pause slide show. c Speed x3/ x2/ x1 – Use ENTER to select a delaying speed between photos in a slide show. d Rotate – Press ENTER to rotate the photo. e Go to list – Press ENTER to return [Photo] menu. Last Scene Memory r This unit memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled. 1. Press SPEAKER LEVEL repeatedly to select a desired speaker to set. 2. Press VOL -/+ to adjust the sound level of the selected speaker while the level setting memu is displayed on the display window. 3. Repeat and adjust the sound level of the other speakers. Operating 29 Setting the Clock Sleep Timer Setting 1. Turn the unit on. Press SLEEP one or more times to select delay time between 10 and 180 minutes, after the unit will turn off. 2. Press CLOCK for at least 2 seconds. 3. Choose time mode by pressing C/V. - AM 12:00 (for an AM and PM display) or 0:00 (for a 24 hour display) 4. Press SET to confirm your selection. 5. Select the hours by pressing C/V. 6. Press SET. 7. Select the minutes by pressing C/V. 8. Press SET. Using your player as an alarm clock 1. Turn the unit on. 2. Press TIMER. Each functions flashes. 4. “ON TIME” will be displayed. This is your desired time to unit turns on. Press C/V to change the hours and minutes and press SET to save. 5. The “OFF TIME” will be displayed. This is your desired time to unit turns off. 6. Press C/V to change the hours and minutes and press SET to save. 7. Press C/V to change the volume and press SET to save. The clock icon “(“ shows that the alarm is set. 8. Press TIMER button 2 times. You can check the setting status. , Note To cancel the sleep function, press SLEEP repeatedly until “SLEEP 10” appears, and then press SLEEP once again while “SLEEP 10” is displayed. , Note You can check the remaining time before the Unit turns off. Press SLEEP The remaining time appears in the display window. Dimmer Press SLEEP once. The display window will be darken by half. To cancel it, press SLEEP repeatedly until dim off. If touch the buttons in Sleep Timer mode, the buttons will be lightening for 5 seconds and darkening again. Turn off the sound temporarily Press MUTE to mute your unit. You can mute your unit, for example, to answer the telephone, the “q” is displayed in the display window. DEMO In the power off state, it demonstrates the function on display window by pressing DEMO. To cancel the DEMO, press it again. , Note If you set the clock time, you can check the time by pressing CLOCK even when the player is turned off. While DEMO, this unit will keep DEMO status even if you unplug the power cord connection. If you set the clock time and alarm, you can check the alarm icon “(“ by pressing CLOCK even when the player is turned off. You can enjoy other functions during the DEMO. Then the DEMO will pause to temporary. If you set the clock time and alarm, you can check the alarm icon “(“ and setting informaiton by pressing TIMER even when the unit is turned off. - Without input key in 10 sec, the DEMO will play back automatically. 4 Operating 3. Press SET when the function you want to be woken by is showing. To check the remaining time, press SLEEP. 30 Operating Radio Operations Be sure that both FM aerials are connected. (Refer to the page 18.) Listening to the radio 1. Press P RADIO&INPUT until FM appears in the display window. The last received station is tuned in. 2. Press and hold TUNING (-/+) for about two seconds until the frequency indication starts to change, then release. Scanning stops when the unit tunes in a station. Or Press TUNING (-/+) repeatedly. 3. Adjust the volume by pressing -/+ on the front panel or by pressing VOL (+/-)on the remote control repeatedly. 4 Operating Presetting the Radio Stations You can preset 50 stations for FM. Before tuning, make sure that you have turned down the volume. 1. Press P RADIO&INPUT until FM appears in the display window. 2. Select the desired frequency by using TUNING (-/+). 3. Press b ENTER a preset number will flash in the display window. 4. Press PRESET (-/+) to select the preset number you want. 5. Press b ENTER. The station is stored. 6. Repeat the steps 2 to 5 to store other stations. Deleting all the saved stations 1. Press and hold CLEAR for two seconds. “ERASE ALL” will flash up on the unit display. 2. Press CLEAR to erase all saved of the radio stations. Deleting a saved station 1. Press PRESET - / + to Select a preset number you want to delete. 2. Press CLEAR, the preset number will blink in the display window. 3. Press CLEAR again, to delete the selectd preset number. Improving poor FM reception Press d PLAY, MONO/STEREO on the remote control. This will change the tuner from stereo to mono and usually improve the reception. Operating Sound adjustment On Display This system has a number of pre-set surround sound fields. You can select a desired sound mode by using SOUND EFFECT. You can change the SOUND EFFECT using A D arrow key while the sound effect information is displayed on. The displayed items for the equalizer maybe different depending on sound sources and effects. You can enjoy more virtual surround sound. BYPASS You can enjoy the sound without equalizer effect. Description NAT PLUS The NAT PLUS is Natural Plus sound effect. You can enjoy the natural sound effect same as a 5.1-channel. NATURAL You can enjoy comfortable and natural sound. Local specialization equalizer Regionally optimized sound effect. (FORRO/ FUNK/ SERTANEJO/ DANGDUT/ ARABIC/ PERSIAN/ INDIA/ REGUETON/ MERENGUE/ SAMBA/ SALSA/ CUMBIA/ AFRO) AUTO EQ Realizes the sound equalizer that is the most similar to the genre of which is included in the MP3 ID3 tag of song files. POP CLASSIC JAZZ ROCK This program lends an enthusiastic atmosphere to the sound, giving you the feeling you are at an actual rock pop, jazz or classic concert. MP3 -- OPT This function is optimized for compressible MP3, WMA file. It improves the treble sound. BASS BLAST During playback, reinforce the treble, bass and surround sound effect. LOUDNESS Improves the bass and treble sound. , Note In some of surround modes, some speakers, there’s no sound or low sound. It depends on the mode of surround and the source of audio, it is not defective. You may need to reset the surround mode, after switching the input, sometimes even after the sound track changed. 4 Operating On Display Description VIRTUAL Setting the surround mode 31 32 Operating Advanced Operations Recording to USB You can record music or sound souce to USB device by connecting in to the port on the unit. During recording MP3/WMA, there is no sound. 1. Connect the USB device to the unit. When you stop recording during playback, the file that has been recorded at that time will be stored. (Audio CD only) 2. Select a mode in which you want to record. Play back a sound source first. 3. Start the recording by pressing X REC. 4. To stop recording, press Z STOP. [All tracks/ files recording] Record to USB in stop or play mode. [Program list recording] After marking desired file(s) and you can record it to USB (Refer to the page 26). 4 , Note You can check the recording percentage rate for the USB record on the screen during the recording. (Audio CD or MP3/ WMA CD only) It’ll be stored as follows. Operating Audio CD MP3/ WMA Do not remove the USB device or turn off the unit during USB recording. If not, an incomplete file may be made and not deleted on PC. If USB recording does not work, the message like “NO USB”, “ERROR”, “USB FULL” or “NO REC” is displayed on the display window. Multi card reader device or external HDD can not be used for USB recording. A file is recorded by 128 Mbyte (about 2 hours) when you record for a long term. There are recorded less than 4 files. When you stop recording during playback, the file will not be stored. In the state CD-G, DTS disc USB record is not operated. The files in the sub-folders are not recorded during all track recording. You may not record more than 999 files. The other sources (Tuner, Portable) The nunbering of the recording file is entered from the lowest number. So if you delete some of the recording files, the next recording file could be the lowest number among them. The making of unauthorized copies of copyprotected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes. Be responsible Respect copyrights. Troubleshooting 33 Troubleshooting PROBLEM No power No picture CORRECTION Plug the power cord into the wall outlet securely. Select the appropriate video input mode on the TV so the picture from the unit appears on the TV screen. Connect the video cables securely to both the TV and unit. Select the correct input mode of the unit so you can hear the sound from the unit. There is little or no sound Connect the audio cables into the connection terminals correctly. Replace with a new audio cable. The DVD picture quality is poor Clean the disc using a soft cloth with outward strokes. Insert a disc. A DVD/CD will not play Insert a playable disc (check the disc type, colour system and regional code). Enter your password or change the rating level. Radio stations can’t be tuned in properly Clean the disc using a soft cloth with outward strokes. Move unit and audio components further away from your TV. 5 Check the antenna connection and adjust its position. Troubleshooting Humming noise heard while a DVD or CD is playing Attach an external aerial if necessary. Tune to the station manually. Preset some radio stations, see page 30 for details. The remote is not pointed directly at the unit. Point the remote directly at the unit. The remote is too far from the unit. Use the remote within 23 feet (7m) of the unit. The remote control doesn’t work well / at all There is an obstacle in the path between the remote control and the unit. Remove the obstacle. The battery in the remote control are flat. Replace the battery with new ones. iPod does not work. Check whether the player is connected to the unit correctly. Connect it to the unit correctly. 34 Appendix Area Code List Choose an area code from this list. Area Code Area Code Area Code Area Code Afghanistan AF Fiji FJ Monaco MC Singapore SG Argentina AR Finland FI Mongolia MN Slovak Republic SK Australia AU France FR Morocco MA Slovenia SI Austria AT Germany DE Nepal NP South Africa ZA Belgium BE Great Britain GB Netherlands NL South Korea KR Bhutan BT Greece GR Antilles AN Spain ES Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK Brazil BR Hong Kong HK Nigeria NG Sweden SE Cambodia KH Hungary HU Norway NO Switzerland CH Canada CA India IN Oman OM Taiwan TW Chile CL Indonesia ID Pakistan PK Thailand TH China CN Israel IL Panama PA Turkey TR Colombia CO Italy IT Paraguay PY Uganda UG Congo CG Jamaica JM Philippines PH Ukraine UA Costa Rica CR Japan JP Poland PL United States US Croatia HR Kenya KE Portugal PT Uruguay UY Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ Denmark DK Libya Ecuador EC Luxembourg LY Russian LU Federation Egypt EG Malaysia 6 El Salvador SV Maldives MY Saudi Arabia MV Senegal Appendix Ethiopia ET Mexico MX Vietnam RU Zimbabwe SA SN VN ZW Appendix 35 Language code List Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu]. Language Code Language Code Language Language Afar 6565 Afrikaans 6570 French 7082 Frisian 7089 Albanian 8381 Ameharic 6577 Galician Georgian Arabic Armenian 6582 German 6869 7289 Greek 6976 Assamese 6583 Greenlandic 7576 Aymara 6588 Guarani 7178 Azerbaijani 6590 Gujarati 7185 Bashkir 6665 Hausa 7265 Basque 6985 Hebrew Bengali; Bangla 6678 Hindi Bhutani 6890 Bihari Breton Lithuanian 7684 Sindhi 8368 Macedonian 7775 Singhalese 8373 7176 Malagasy 7771 Slovak 8375 7565 Malay 7783 Slovenian 8376 Malayalam 7776 Spanish 6983 Maori 7773 Sudanese 8385 Marathi 7782 Swahili 8387 Moldavian 7779 Swedish 8386 Mongolian 7778 Tagalog 8476 Nauru 7865 Language Code 7387 Nepali 7869 Tajik 8471 7273 Norwegian 7879 Tamil 8465 Hungarian 7285 Oriya 7982 Telugu 8469 6672 Icelandic 7383 Panjabi 8065 Thai 8472 6682 Indonesian 7378 Pashto, Pushto 8083 Tonga 8479 Bulgarian 6671 Interlingua 7365 Persian 7065 Turkish 8482 Burmese 7789 Irish 7165 Polish 8076 Turkmen 8475 Byelorussian 6669 Italian 7384 Portuguese 8084 Twi 8487 Chinese 9072 Japanese 7465 Quechua 8185 Ukrainian 8575 Croatian 7282 Kannada 7578 Rhaeto-Romance 8277 Urdu 8582 Czech 6783 Kashmiri 7583 Rumanian 8279 Uzbek 8590 Danish 6865 Kazakh 7575 Russian 8285 Vietnamese 8673 Dutch 7876 Kirghiz 7589 Samoan 8377 Volapük 8679 English 6978 Korean 7579 Sanskrit 8365 Welsh 6789 Esperanto 6979 Kurdish 7585 Scots Gaelic 7168 Wolof 8779 7679 Serbian 8382 Xhosa 8872 Laothian Estonian 6984 Faroese 7079 Latin Fiji 7074 Finnish 7073 Code 7665 Serbo-Croatian 8372 Yiddish 7473 Latvian, Lettish 7686 Shona 8378 Yoruba 8979 Lingala 7678 Zulu 9085 6 Appendix Code 36 Appendix Trademarks and Licenses iPod is a trademark of Apple Inc., registered in the U.S. and other countries. iPhone is a trademark of Apple Inc. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone may affect wireless performance. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. 6 Appendix “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation. DivX®, DivX Certified® and associated logos are trademarks of DivX, Inc. and are used under license. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified® device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration. What is SIMPLINK? Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection. Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc. Refer to the TV owner’s manual for the details of SIMPLINK function. LG TV with SIMPLINK function has the logo as shown above. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Use a higher version cable than High Speed HDMI™ cable. Appendix 37 Specifications General Power requirements refer to main label Power consumption refer to main label Dimensions (W x H x D) 135 X 295 X 315 mm without foot Net Weight (Approx.) 3.45 kg Operating temperature 41 °F to 95 °F (5 °C to 35 °C) Operating humidity 5 % to 90 % Inputs/ Outputs VIDEO OUT 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2 HDMI OUT (video/audio): 19 pin Type A, HDMI™ Connector DIGITAL IN (OPTICAL): 3 V (p-p), Optical jack x 1 PORT. IN 0.5Vrms (3.5 mm stereo jack) System Laser Semiconductor laser, wavelength: 650 nm Signal system Standard NTSC/ PAL color TV system Frequency response 20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling) More than 80 dB Harmonic distortion 0.05 % at 1 W Dynamic range More than 85 dB Bus Power Supply USB DC 5 V 0 500 mA iPod DC 5 V 0 1 A Amplifier Stereo mode 80 W + 80 W (4Ω at 1kHz) Tuner FM Tuning Range 87.5 to 108.0 MHz or 87.50 to 108.00 MHz 6 Appendix Signal-to-noise ratio 38 Appendix Front Speaker Type 3 Way 4 speaker Impedance Rated 4Ω Input Power 80 W Max. Input Power 160 W Net Dimensions (W x H x D) 126 X 295 X 315 mm Net Weight 4.35 kg Design and specifications are subject to change without notice. 6 Appendix Appendix 39 Maintenance Notes on Discs Handling Discs Handling the Unit When shipping the unit Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Keeping the exterior surfaces clean Do not use volatile liquids such as insecticide spray near the unit. Wiping with strong pressure may damage the surface. Do not leave rubber or plastic products in contact with the unit for a long period of time. Cleaning the unit To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc. Storing Discs After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. Cleaning Discs Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center to out. Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records. Maintaining the Unit 6 Appendix The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service center.