LG | BX503B | LG BX503B Owner’s Manual

OWNER’S MANUAL
DLP PROJECTOR
Please read this manual carefully before operating
your set and retain it for future reference.
BX503B
BX403B
www.lg.com
DLP PROJECTOR
Warning - Class B
(b) F
or a Class B Digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:
NOTE: T
his equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
2
Contents
Contents
Safety Instructions........................................................ 4
Names of parts
Main Body...........................................................................................7
Control Panel......................................................................................7
Connecting Part............................................................................... 8
Remote Control .............................................................................. 8
Installing Batteries............................................................................ 9
Projector Status Indicators...........................................................10
Accessories........................................................................................ 11
Optional Extras ................................................................................ 11
Installing and Composition
Installation Instructions..................................................................12
Basic Operation of the Projector................................................13
Using Kensington Security System............................................14
Turning on the Projector...............................................................15
Turning off the Projector...............................................................15
Focus and Position of the Screen Image.................................16
Selecting source mode.................................................................16
Connection
Connecting
Connecting
Connecting
Connecting
Connecting
to
to
to
to
to
a
a
a
a
a
Desktop PC....................................................... 17
Notebook PC.................................................... 17
Video Source.................................................... 17
DVD.....................................................................18
D-TV Set-Top Box...........................................18
Function
Video Menu Options
Adjusting Video .............................................................................19
Picture mode....................................................................................19
Color Temperature Control..........................................................20
Gamma Function............................................................................20
Gamma curve shift Function......................................................20
Brilliant color TM Function.............................................................21
White peaking Function.................................................................21
Black level Function........................................................................21
Expert color Function....................................................................22
Reset ................................................................................................22
Using the Digital Zoom Function..............................................26
To make the project turn on when power is applied............26
Using the keystone function....................................................... 27
Using the Blank Function............................................................. 27
Selecting a Blank image..............................................................28
Screen Capture Function................................................................28
Lamp mode Function...................................................................28
Using the Monitor out Function.................................................29
Communication setting................................................................29
High Altitude Mode.......................................................................29
Checking lamp time......................................................................30
Using Still Function........................................................................30
Screen Menu Options
Auto configure Function..............................................................30
Using the Phase Function............................................................31
Using the Clock Function.............................................................31
Using the Horizontal Function.....................................................31
Using the Vertical Function..........................................................31
Serial communication function
SET ID...............................................................................................32
To connect with serial communication.....................................32
Network setting function
Using the network setting............................................................ 37
Information
Supported Monitor Display..........................................................39
Replacing the Lamp......................................................................40
How to attach the lens cap to the projector..........................42
Specifications..................................................................................43
Special Menu Options
Selecting Language......................................................................23
Using ARC Function......................................................................23
Overscan Function.........................................................................23
Flip horizontal Function................................................................24
Flip vertical Function......................................................................24
Sleep time Function......................................................................24
Auto sleep Function......................................................................25
Presentation timer Function........................................................25
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream
via designated collection facilities appointed by your government or your local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste
disposal service or the shop where you purchased the product.
5. The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this
product with general household waste. Disposal of this product must be carried out in accordance to the
regulations of your local authority.
3
Safety Instructions
Safety Instructions
Please take note of the safety instructions to prevent any potential accident or misuse of the projector.
ꔈ Safety Instructions are given in two forms as detailed below.
WARNING : The violation of this instruction may cause serious injuries and even death.
NOTES : The violation of this instruction may cause injuries or damage to the projector.
ꔈ After reading this manual, keep it in the place that you can access easily.
Indoor Installation
Do not place the Projector in direct
sunlight or near heat sources such
as radiators, fires, stove etc.
This may cause a fire hazard or product
defect.
Do not block the vents of the projector or restrict air-flow in any way.
This would cause the internal temperature to increase and could cause a fire
hazard or damage to the unit!
WARNING
Do not place flammable materials in, on or near the projector.
Do not hang on an installed
projector.
This may cause a fire hazard or product defect.
It may cause the projector to fall,
causing injury or death.
Do not place the projector close
to sources of steam or oil such
as a humidifier.
Do not place the projector where
it might be exposed to dust.
This may create a fire hazard or an
electric shock hazard!
Do not use the projector in a
damp place such as a bathroom
where it is likely to get wet.
Do not place the projector directly on a carpet, rug or place where
ventilation is restricted.
This may cause a fire or an electric
shock hazard!
This would cause its internal temperature to increase and might create a
fire hazard or damage the unit.
Indoor Installation
When installing the projector on
a table, be careful not to place it
near the edge.
Earth wire should be connected.
Ensure that you connect the earth ground
wire to prevent possible electric shock (That
is a Projector with a three-prong grounded
AC plug must be connected to a threeprong grounded AC outlet).
If grounding methods are not possible, have
a qualified electrician install a separate circuit
breaker.
Do not try to ground the unit by connecting
it to telephone wires, lightening rods, or gas
pipes.
4
Ensure good ventilation around the
projector. The distance between
the projector and the wall should
be more than 30 cm.
An excessive increase in its internal temperature may cause a fire hazard or
damage to the unit!
NOTES
Disconnect from the power supply and remove all connections
before moving, or cleaning.
The projector could fall causing injury
and damage to the projector.
Only use a suitable stand.
Power
This may cause a fire hazard or damage to the unit!
Only use the projector on a level
and stable surface.
It may fall and cause injury and/or
damage to the unit.
WARNING
The power cord should be inserted
fully into the power outlet to avoid
a fire hazard!
This may cause a fire hazard or damage
the unit.
Do not place heavy objects on
the power cord.
This may cause a fire or an electric
shock hazard!
Safety Instructions
Power
WARNING
Never touch the power plug with
a wet hand.
Do not plug-in too many items
into one power outlet.
Prevent dust from collecting on
the power plug pins or outlet.
This may cause an electric shock
hazard!
It may result in overheating of the outlet and create a fire hazard!
This may cause a fire hazard!
Power
NOTES
Hold the plug firmly when
unplugging. If you pull the cord,
it may be damaged.
Do not use if the power cord or
the plug is damaged or any part
of the power outlet is loose.
Ensure the power cord does not
come into contact with sharp or
hot objects.
This may cause a fire hazard!
This may cause a fire or an electric
shock hazard or damage to the unit!
This may cause a fire or an electric
shock hazard or damage to the unit!
Place the projector where people
will not trip or tread on the power
cord.
Do not turn the projector On/Off by plugging-in or unplugging the
power plug to the wall outlet.
(Allow the unit to cool before removing power.)
This may cause a fire or an electric
shock hazard or damage to the unit!
It may cause mechanical failure or could cause an electric shock.
Using
WARNING
Do not place anything containing
liquid on top of the projector
such as flowerpot, cup, cosmetics or candle.
In case of impact shock or damage Do not allow any objects to fall
to the projector switch it off and
into the projector.
unplug it from the power outlet and
contact an authorized service center. This may cause an electric shock haz-
This may cause a fire hazard or damage to the unit!
This may cause a fire or an electric shock
hazard or damage to the unit!
ard or damage to the unit!
If water is spilt into the projector unplug it from the power supply
immediately and consult your Service Agent.
Dispose of used batteries
carefully and safely.
This may cause an electric shock hazard or damage to the unit!
In the case of a battery being
swallowed by a child please consult
a doctor immediately.
Do not remove any covers. High
risk of Electric Shock!
Don’t look directly into the lens
when the projector is in use. Eye
damage may occur!
Do not touch metal parts during
or soon after operation since the
vents will remain very hot!
CAUTION concerning the Power Cord
It is recommend that most appliances be placed on a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits.Check the specification
page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous.Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by authorized service personnel.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
5
Safety Instructions
Using
WARNING
If the projector is in a room that experiences a gas leak, do not touch
the projector.
It can cause a fire or a burn by a spark.
Using
Always open the lens door or
remove the lens cap when the
projector lamp is on.
NOTES
Do not place heavy objects on
top of projector.
This may cause mechanical failure or
personal injury!
Do not use any sharp tools on
the projector as this will damage
the casing.
Take care not to impact the lens
particularly when moving the
projector.
In the event that an image does
not appear on the screen please
switch it off and unplug it from the
power outlet and contact your
Service Agent.
Do not touch the lens of the projector. It is delicate and easily
damaged.
Do not drop the projector or
allow impact shock.
This may cause mechanical failure or
personal injury!
This may cause a fire or an electric
shock hazard or damage to the unit!
Cleaning
WARNING
Do not use water while cleaning
the projector.
This may cause damage to the projector or an electric shock hazard.
In the unlikely event of smoke or
a strange smell from the projector, switch it off, unplug it from
the wall outlet and contact your
dealer or service center.
Use an air spray or soft cloth that
is moist with a neutral detergent
and water for removing dust or
stains on the projection lens.
This may cause a fire or an electric
shock hazard or damage to the unit!
Cleaning
Contact the Service
Center once a year to
clean the internal
parts of the projector.
Accumulated dust can
cause mechanical failure.
NOTES
When cleaning the plastic parts such as projector case, unplug the power and
wipe it with a soft cloth. Do not use cleanser, spray water or wipe with a wet
cloth. Especially, never use cleanser (glass cleaner), automobile or industrial
shiner, abrasive or wax, benzene, alcohol etc., which can damage the product.
Use an air spray or soft cloth that is moist with a neutral detergent and water
for removing dust or stains on the projection lens.
It can cause fire, electric shock or product damage (deformation, corrosion and damage).
Others
WARNING
Do not attempt to service the projector yourself. Contact your dealer or service center.
This may cause damage to the projector and could give an electric Shock as well as invalidating the warranty!
Others
6
NOTES
Do not mix new batteries with old
batteries.
Be sure to unplug if the projector is
not to be used for a long period.
Only use the specified type
of battery.
This may cause the batteries to overheat and leak.
Accumulated dust may cause a fire hazard or damage to the unit!
This could cause damage to the
remote control.
Names of parts
Names of parts
Main Body
• T
he projector is manufactured using high-precision technology. You may, however, see on the Projector screen tiny black
points and/or bright points (red, blue, or green). This can be a normal result of the manufacturing process and does not
always indicate a malfunction.
Control panel
Focus ring
Power button
Front remote control sensor
Zoom ring
Foot adjusting button
Control Panel
MENU Button
Selects or closes menus.
INPUT Button
Switches to RGB(Component), HDMI, Video
mode.
∧/∨/</> Button
Adjusts functions of menus.
AUTO Button
It automatically corrects the
position and the shaking of the
image at the RGB mode.
◉ OK Button
Checks present mode and saves the
function changes.
POWER Button
Turn ON/OFF the projector.
7
Names of parts
Connecting Part
VIDEO IN
RGB IN-2
RGB IN-1
RGB OUT
HDMI IN
Rear remote control sensor
USB(SVC only)
RS-232C
LAN
AC IN
Kensington Security
System Connector
(Refer to page 14)
Remote Control
POWER Button
RATIO Button
AUTO Button
INPUT Button
EXIT Button
MENU Button
OK ◉ </>/∧/∨ Button
Contrast Button
Brightness Button
KEYSTONE Button
SLEEP Button
MODE Button
ZOOM Button
STILL Button
LAMP Button
BLANK Button
TIMER Button
WLPHU
FLIP H. Button
FLIP V. Button
8
Names of parts
POWER Button
RATIO Button
AUTO Button
INPUT Button
EXIT Button
MENU Button
OK ◉ </>/∧/∨ Button
Contrast Button
Brightness Button
LASER Button
SLEEP Button
MODE Button
KEYSTONE Button
STILL Button
LAMP Button
BLANK Button
ZOOM Button
FLIP H. Button
FLIP V. Button
< Australia, Switzerland, Slovenia, Netherlands,
Germany, Spain, France, Greece, Italy, Poland,
Hungary, Portugal, Romania, Sweden, Finland,
Denmark, United Kingdom only >
Laser Button
* Produces a bright red laser pointer on the
screen for the purpose of indication.
(Don’t look at laser beam directly as it
can cause eye damage!)
Installing Batteries
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
• Open the battery compartment cover on the back of the remote control.
• Insert the specified type of batteries with correct polarity, match “+” with “+”, and
match “-” with “-”.
• Install two 1.5V AAA batteries. Don’t mix used batteries with new batteries.
9
Names of parts
Projector Status Indicators
*Lamp indicator, operation indicator and temperature indicator at the top of the projector show the user the operating
status of the projector.
Temperature Indicator
Lamp Indicator
Operation Indicator
Operation Indicator
Red
Green(flashing)
Green
Orange(flashing)
Off
Orange
Red(flashing)
Red
Lamp Indicator
Red(flashing)
Green(flashing)
Orange
Temperature Indicator
Red
Red (flashing)
Green(flashing)
10
Standby.
Lamp is starting up.
Unit is in operation (Lamp is turned on)
Projector lamp is cooling (20 sec.)
Power off.
Standby-This mode cools the projector for 4 minutes
after it is turned off.
This indicates a Color Wheel problem.
Please contact your local service center.
Projector lamp is reaching the end of its life and needs
to be replaced with a new lamp.
The projector is experiencing an error. Retry Power On
again later. If lamp indicator is red (flashing) again,
contact a service center.
The lamp cover is open.
A high temperature state has been detected. Turn the
Projector off.
The Projector has turned off due to excessive heat.
Power has turned off due to problem with the internal
cooling fan. Contact your service center.
It is a problem of TEC, contact a service center.
(BX503B only)
Names of parts
Accessories
Remote Control
Power Cord
AAA Battery
Computer Cable
Owner’s manual
Lens cap and Strap
CD Owner’s manual
ez-net Program CD
Optional Extras
• • • • Contact your dealer to purchase these items.
Contact your service personnel for replacing of lamp.
The lamp is consumable and needs to be replaced with a new one when it is burned out.
Optional parts can be changed without notice to improve the quality of the product, and new optional parts can be added.
Ceiling installer for projector
Projection Screen
Lamp
LAN Cable
Component Cable
HDMI Cable
RS-232C Cable
RCA to D-Sub Adapter
Video Cable
HDMI to DVI Cable
11
Installing and Composition
Installing and Composition
Installation Instructions
* Please read all of the following installation warnings.
Provide proper ventilation for this projector.
• he projector is equipped with ventilation holes(intake) on
T
the bottom and ventilation holes(exhaust) on the front. Do
not block or place anything near these holes, or internal
heat build-up may occur, causing picture degradation or
damage to the projector.
• N
ever push projector or spill any kind of liquid into the
projector.
• o not place the projector on a carpet, rug or
D
other similar surface. It may prevent a adequate
ventilation of the projector bottom. This product
should be mounted to a wall or ceiling only.
• eave an adequate distance(30cm/12 inches or
L
more) around the projector.
Place this projector in adequate temperature and humidity conditions.
• Install this projector only in a location where adequate temperature and humidity is available. (refer p.43)
Don’t place the projector where it can be covered with dust.
• This may cause overheating of the projector.
Do not obstruct the slots and openings of the projector. This may cause overheating and create a fire hazard.
The projector is manufactured using high-precision technology. You may, however, see tiny black points and/or
bright points (red, blue, or green) that continuously appear on the projector Screen. This is a normal result of
the manufacturing process and does not indicate a malfunction.
To display DTV programs, it is necessary to purchase a DTV receiver (Set-top Box) and connect it to the projector.
When the remote control does not work during operation.
• T
he remote control may not work when a lamp equipped with electronic ballast or a three-wavelength lamp is installed.
Replace those lamps with international standard products to use the remote control normally.
12
Installing and Composition
Basic Operation of the Projector
1. Place the projector on a sturdy and horizontal surface with the PC or AV source.
2. Place the projector with the desired distance from the screen. The distance between the projector and the screen
determines the actual size of the image.
3. Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right
angle, the screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to
page 27.).
4. Connect the cables of the projector to a wall power socket and other connected sources.
projection distance based on the picture format
Screen
X/2
Projection off-set ratio:100%
Screen height (X)
X/2
Projection distance (D)
Screen Width (Y)
Y/2
Screen
Y/2
Projection distance (D)
4 : 3 Scale
Diagonal Size
(mm)
Horizontal Size
(mm)
Projection Distance
Vertical Size
(mm)
Wide Distance Tele Distance
(mm)
(mm)
*T
he longest/shortest distance
show status when adjusted by
the zoom function.
13
Installing and Composition
Using Kensington Security System
• T
he projector has a ‘Kensington’ Security System Connector on the side panel. Connect the ‘Kensington’ Security System cable as
below.
• For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached to the Kensington
Security System set.
• And for further information, contact http://www.kensington.com, the internet homepage of the Kensington company that
deals with expensive electronic equipment such as notebook PCs or projectors.
• Kensington Security System is an optional item.
14
Installing and Composition
Turning on the Projector
1. Connect power cord correctly.
2. Remove the lens cap. If it is left on, it could become deformed due to the heat produced by the projection lamp.
3. Press the POWER button on the remote control or top cover. (Green operation indicator flashes if lamp is in start-up
cycle.)
• An image will appear after the operation indicator light turns (Green).
• Select the source mode with the INPUT button.
Do not disconnect the power cord while the fan is in operation. If the power cord is disconnected while the fan is in operation, it may takes longer
to activate the lamp after turning on the power and the lifespan of the lamp may be shortened.
Turning off the Projector
1. Press the POWER button on the top cover or remote control.
2. Press the POWER button on the top cover or remote control again to turn off the power.
3. If the operation indicator LED is orange and blinking, do not disconnect(20 sec.) the power until the operation
indicator LED is lit constantly (orange).
• If the operation indicator LED is orange and blinking, the power button on the top cover or on the remote control will not
operate.
• This projector features the Quick Power On/Off function that allows a user to turn it on and off quickly.
Power off?
Please press Power key again.
* What is the Quick Power On/Off function?
The projector enters into Standby mode without waiting until it is cooled.
If Standby mode continues for a certain amount of time, the projector can operate without cooling when it is turned on.
15
Installing and Composition
Focus and Position of the Screen Image
When an image appears on the screen, check if it is in focus and fits well to the screen.
Focus ring
Zoom ring
• To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
• To adjust the size of the image, rotate the zoom ring which is the inner ring on the lens.
To raise or lower the image on the screen, extend or retract the foot at the bottom of the projector by
pushing foot adjusting button as below.
Foot adjusting button
1. W
hile pressing the foot adjusting button, raise or lower the projector to place the screen image in the proper
position.
2. Release the button to lock the foot in its new position.
3. Turn the foot at the back left or right to make a fine tune of the length of the projector.
4. After raising the front foot, do not press down on the projector.
Selecting source mode
1.Press the INPUT button on the remote control or the control panel.
RGB1
RGB2
HDMI
Video
MENU
Exit
◉
OK
2.After moving into desiring input by pressing ∧, ∨ button, please press the confirm button.
• W
hen a signal cable is plugged in and there ’s a signal, the selected item is activated as white,and if there ’s no signal, the
selected item is deactivated as gray.
• The input button only toggles through the active inputs.
• Component inputs can be connected to RGB1 and RGB2 using a special cable. RGB1 and RGB2 do not show as active
inputs even when a device is connected to them.
16
Connection
Connection
Connecting to a Desktop PC
* You can connect the projector to a computer with VGA, SVGA, XGA and SXGA output.
* Refer to page 39 for the resolutions supported by the projector.
* Either RGB1 or RGB2 can be used with the RGB OUT connection. You can select between the two in the Monitor Out menu.
<To use by connecting to RGB>
Connect the RGB IN 1 of the projector and the computer output port with computer cable.
• You can also connect to the RGB IN 2 port.
Computer Cable
<To use by connecting to HDMI terminal>
Please connect projector ’s HDMI IN terminal and computer ’s output terminal by using HDMI to DVI cable.
• You can also connect to the RGB IN 2 port.
Connecting to a Notebook PC
HDMI to DVI Cable
< How to connect >
Connect the RGB IN 1 of the projector and the computer output
port with computer cable.
• If you set your computer to output the signal to both the
display of your computer and the external projector, the
picture of the external projector may not appear properly.
In such cases, set the output mode of your computer to
output the signal only to the external projector. For details,
refer to the operating instructions supplied with your
computer.
• You can also connect to the RGB IN 2 port.
Computer Cable
Connecting to a Video Source
• You can connect a VCR, a camcorder or any other compatible video image source to the projector.
< How to connect >
onnect the Video input jacks of the projector to the
C
output jacks of the A/V source with Video cable.
Video Cable
<VCR>
17
Connection
Connecting to a DVD
* The output jacks (Y, PB, PR) of the DVD might be labeled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to the equipment.
< How to connect >
Connect the DVD Component cable to the RCA to D-Sub Adapter and then connect the RCA to D-Sub Adapter to RGB IN 1 of the projector.
• W
hen connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)
• You can also connect to the RGB IN 2 port.
Signal
Component
480i
O
X
480p
O
O
RCA to D-Sub adapter
Component cable
HDMI/DVI
720p
O
O
1080i
O
O
576i
O
X
576p
O
O
1080p
(24,30Hz)
O
O
Connecting to a D-TV Set-Top Box
*To receive D-TV programs, it is necessary to purchase a D-TV receiver (Set-Top Box) and connect it to the projector.
*Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and D-TV Set-Top Box.
< How to connect a HDMI source >
1. C
onnect the HDMI IN terminal of the projector to the HDMI
output terminal of the D-TV Set-Top Box via HDMI cable.
2. Use a DTV receiver with DTV 480p(576p)/720p/1080i/1080p
(24,30Hz) mode.
HDMI Cable
• No support of audio.
<D-TV Set-Top Box>
< How to connect a Component source >
onnect the D-TV Set-Top Box Component cable to the RCA to
C
D-Sub Adapter and then connect the RCA to D-Sub Adapter to
RGB IN 1 of the projector.
• W
hen connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)
• You can also connect to the RGB IN 2 port.
• No support of audio.
18
<D-TV Set-Top Box>
Component cable
RCA to D-Sub adapter
<D-TV Set-Top Box>
Function
Function
*In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just an example to help with
the Projector operation.
*This operating guide explains operation of RGB(PC) mode mainly.
Video Menu Options
< RGB mode >
Adjusting Video
1. Press the MENU button and then use <,> button to select the
menu.
2.Press the ∧,∨ button to select a video item you want to adjust.
3.Press the <,> button to adjust the screen condition as you want.
Picture mode
Contrast
Brightness
Sharpness
Color R
Color G
Color B
MENU Exit
<
Golf
>
56
50
50
50
50
50
<> Move
◉ OK
< Video mode >
• Each adjustment of
menu options will not affect other inputs.
• Color mode is displayed and adjustable for 60Hz component, external input or
NTSC signal only.
• You can adjust contrast by pressing the
button on the remote control.
button on the remote control.
• You can adjust brightness by pressing the
• Press the MENU button twice or the EXIT button to exit the menu screen.
Picture mode
Contrast
Brightness
Color
Sharpness
Tint
MENU Exit
<
Normal
>
50
50
50
50
0
<> Move
◉ OK
Picture mode
* Use Picture mode function to set the projector for the best picture appearance.
1. Press the MODE button on the remote control.
2. Press the <,> button to adjust the screen condition as you want.
Normal
User
Bright
Presentation
Sports
Film
Golf
Game
• You can use this function through the MENU button.
• To exit the menu display, press the EXIT button.
19
Function
Color Temperature Control
* To initialize values (reset to default settings), select the Natural option.
1. P
ress the MENU button and then use <,> button to select the
menu.
2. Press the ∧,∨ button to select Color temp. item.
3. Press the <,> button to make desired adjustments.
• Each press of the <,> button changes the screen as shown below.
Natural
Cool
Medium
<
Color temp.
<
Gamma
Gamma curve shift
<
Brilliant color TM
White peaking
10
Expert Color
Reset
Warm
MENU Prev.
ꕌ Move
ꕍ
Natural
>
Normal
>
On
>
<>Select
• T
his function can be inactivated depends on the Picture mode. When the Picture mode is set in Bright or Golf, you
can’t adjust Color temperature function.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Gamma Function
1. P
ress the MENU button and then use <,> button to select the
menu.
2. Press the ∧,∨ button to select Gamma item.
3. Press the <, > button to select the screen condition you want.
Middle
High
Maximum
Cinema
Low
<
Color temp.
<
Gamma
Gamma curve shift
<
Brilliant color TM
White peaking
10
Expert Color
Reset
MENU Prev.
ꕌ Move
ꕍ
Natural
>
Normal
>
On
>
<>Select
• You can use this function through the MENU button.
• To exit the menu display, press the EXIT button.
Gamma curve shift Function
* T
his function shifts the gamma curves for Red, Green and Blue individually to
adjust brightness.
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select Gamma curve shift item.
3. Press the ◉ OK button.
4. When the window below appears, press ∧,∨ button to move between
the items and the <,> buttons to adjust the screen as you want.
• Gamma curve shift Red, Green, Blue can be adjusted between -20 and 20.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Gamma Curve Shift Red
0
Gamma Curve Shift Green 0
Gamma Curve Shift Blue
0
Reset
ꕌ
◉ Prev.
ꕍ Move
20
<> Adjust
<
Color temp.
<
Gamma
Gamma curve shift
<
Brilliant color TM
White peaking
10
Expert Color
Reset
MENU Prev.
ꕌ Move
ꕍ
Natural
>
Normal
>
Press OK Key
On
>
<>Select
Function
Brilliant color
TM
Function
1. P
ress the MENU button and then use <,> button to select the
menu
2. Press the ∧,∨ button to select Brilliant color TM item.
3. Press the <,> button to select On or Off.
• Press the MENU button twice or the EXIT button to exit the menu screen.
* What is the Brilliant color TM function?
<
Color temp.
<
Gamma
Gamma curve shift
<
Brilliant color TM
White peaking
10
Expert Color
Reset
MENU Prev.
his function increases the entire brightness of the screen or decreases it a little to
T
make the rich grayscale color.
ꕌ Move
ꕍ
Natural
>
Normal
>
On
>
<>Select
White peaking Function
1. P
ress the MENU button and then use <,> button to select the
menu
2. Press the ∧,∨ button to select White peaking item.
3. Press the <, > button to select the screen condition you want.
• The default value may change depending on input mode.
• White peaking can be adjusted from 0 to 10.
• Adjust to higher setting to achieve brighter picture. Adjust to lower setting for
darker picture.
• You can use this function through the MENU button.
• To exit the menu display press the EXIT button.
<
Color temp.
<
Gamma
Gamma curve shift
<
Brilliant color TM
White peaking
10
Expert Color
Reset
MENU Prev.
ꕌ Move
ꕍ
Natural
>
Normal
>
On
>
<>Select
Black level Function
1. P
ress the MENU button and then use <,> button to select the
menu
2. Press the ∧,∨ button to select Black level item.
3. Press the <,> button to select Low or High.
• This function works in the following mode : H
DMI(Only activates in DTV signal),
Video
• To exit the menu display, repeatedly press the MENU button.
* What is the Black level function?
<
Color temp.
<
Gamma
Gamma curve shift
<
Brilliant color TM
White peaking
10
Black level
<
Expert Color
Reset
ꕌ Move
MENU Prev.
ꕍ
Natural
>
Normal
>
On
>
High
>
<>Select
hen you watch the movie, this function adjusts the set to the best picture
W
appearance. Adjusting the contrast and the brightness of the screen using the
black level of the screen.
21
Function
Expert color Function
*T
his function allows a user to adjust the Gain, Saturation and Hue for Red, Green,
Blue, Cyan, Magenta and Yellow individually.
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select Expert Color item.
3. Press the ◉ OK button.
Red Gain
50
Green Gain
50
Blue Gain
50
Cyan Gain50
Mgt Gain
50
Yellow Gain
50
Saturation-Red
50
Saturation-Green 50
Saturation-Blue
50
Saturation-Cyan
50
Saturation-Mgt
50
Saturation-Yellow 50
Hue-Red 0
Hue-Green
0
Hue-Blue 0
Hue-Cyan 0
Hue-Mgt 0
Hue-Yellow
0
Reset
ꕌ Move
◉ Prev.
ꕍ
<
Color temp.
<
Gamma
Gamma curve shift
<
Brilliant color TM
White peaking
10
Expert Color
Reset
MENU Prev.
ꕌ Move
ꕍ
Natural
>
Normal
>
On
>
Press OK key
◉ OK
<> Adjust
4. When the window above appears, press <,> button.
Red Gain
◉ Exit
50
ꕌ Move
ꕍ
<>
Adjust
5. Press the ∧,∨ button to move between the items and the <,> buttons to adjust the screen as you want.
• • • • • R
ed, Green, Blue, Cyan, Magenta and Yellow Gain can be adjusted between 0 and 100.
Saturation-Red, Green, Blue, Cyan, Magenta and Yellow can be adjusted between 0 and 100.
Hue-Red, Green, Blue, Cyan, Magenta and Yellow can be adjusted between -50 and 50.
Press the MENU button twice or the EXIT button to exit the menu screen.
An advanced settings function is possible to be saved according to an image mode.
Reset
• To return to the factory default settings, select [Reset] with ∧,∨ buttons and press ◉OK button.
22
Function
Special Menu Options
Selecting Language
1. Press the MENU button and then use <,> button to select the
menu.
2. Press the ∧,∨ button to select Language item.
3. Press the <,> button to select the language you want to use.
• On-Screen-Display (OSD) is displayed in the selected language.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Language
Aspect Ratio
Overscan
Flip horizontal
Flip vertical
Sleep time
Auto sleep
Presentation timer
Digital Zoom
Auto Power
MENU Prev.
<
English
>
<
4:3
>
<
10%
>
<
Off
>
<
60 Min
>
<
Off
>
ꕌ Move
ꕍ
<> Select
Using ARC Function
1. Press the RATIO button.
Each press of the button changes the display as below.
<
4:3
>
<
16:9 >
<
15:10 >
• You can also use this function by using the MENU button.
Overscan Function
1. Press the MENU button and then use <,> button to select the
menu.
2. Press the ∧,∨ button to select Overscan item.
3. Press the <,> buttons.
• T
he Overscan function can be adjusted only in RGB, HDMI and Component
modes.
• The Overscan function can be adjusted between Off and 10%.
• The Overscan function can not be adjusted if the Zoom -/+ in Digital Zoom is set
to a value other than 100%.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Language
Aspect Ratio
Overscan
Flip horizontal
Flip vertical
Sleep time
Auto sleep
Presentation timer
Digital Zoom
Auto Power
MENU Prev.
<
English
>
<
4:3
>
<
10%
>
<
Off
>
<
60 Min
>
<
Off
>
ꕌ Move
ꕍ
<> Select
23
Function
Flip horizontal Function
*This function reverses the projected image horizontally.
Use this function when rear projecting an image.
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select Flip horizontal item.
3. Press the ◉ OK button to see reversed image.
• Each time you press the ◉ OK button, the image will be reversed.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Language
Aspect Ratio
Overscan
Flip horizontal
Flip vertical
Sleep time
Auto sleep
Presentation timer
Digital Zoom
Auto Power
MENU Prev.
<
English
>
<
4:3
>
<
10%
>
To flip
<
Off
>
<
60 Min
>
<
Off
>
ꕌ Move
ꕍ
◉ OK
Flip vertical Function
*This function reverses the projected image vertically.
*When you hang the projector upside down from the ceiling,
you will need to reverse the image vertically and horizontally.
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select Flip vertical item.
3. Press the ◉ OK button to see reversed image.
• Each time you press the ◉ OK button, the image will be reversed.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Sleep time Function
* The sleep timer turns the projector off at the preset time.
1. Press the SLEEP button of remote control.
2. Press the <, > button to select the desired preset time.
• Each press of the <, > button changes the screen as shown below.
Off
240 Min
10 Min
20 Min
180 Min
30 Min
120 Min
• You can use this function through the MENU button.
• To exit the menu display press the EXIT button.
24
60 Min
90 Min
Language
Aspect Ratio
Overscan
Flip horizontal
Flip vertical
Sleep time
Auto sleep
Presentation timer
Digital Zoom
Auto Power
MENU Prev.
<
English
>
<
4:3
>
<
10%
>
To flip
<
Off
>
<
60 Min
>
<
Off
>
ꕌ Move
ꕍ
◉ OK
Function
Auto sleep Function
* This function turns the projector off automatically after the preset time is passed
when there is no signal.
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select Auto sleep item.
3. Press the <, > button to select the desired preset time.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Off
10 Min
20 Min
30 Min
60 Min
Language
Aspect Ratio
Overscan
Flip horizontal
Flip vertical
Sleep time
Auto sleep
Presentation timer
Digital Zoom
Auto Power
MENU Prev.
240 Min
180 Min
120 Min
<
English
>
<
4:3
>
<
10%
>
<
Off
>
<
60 Min
>
<
Off
>
ꕌ Move
ꕍ
<> Select
90 Min
Presentation timer Function
1. Press
2. Press
3. Press
4. Press
the
the
the
the
MENU button and then use <, > button to select the
∧,∨ button to select Presentation timer item.
◉ OK button.
∧,∨ button to select Time alarm or Time keeper item.
Time alarm
Time Keeper
MENU
Exit
<
<
ꕌ Move
ꕍ
Off
>
Off
>
menu.
<> Select
5. Press the <, > button to select the desired preset time.
6. The timer starts to operate if you select specific time.
• Time alarm function : If you select a specific time, it is displayed in minute units. After 1 minute, the remaining time is displayed at the bottom right of the screen, and then disappears after 5 seconds. When the remaining time
is displayed, other OSD windows are closed. When the set time is reached, ‘0 minute’ flickers 10 times at
1 second intervals, and then disappears.
• Time keeper function : If you select a specific time, it continues to be displayed in minute(‘) and second(“) units. Even though
other OSD windows appear, the remaining time is displayed again after the windows are closed. When
the set time is reached. 0’ 00” flickers 10 times at 1 second intervals, and then disappears.
• The Time alarm function and the Time keeper function cannot be used at the same time.
• The Time alarm function can be set from 5 to 60 minutes at 5 minute intervals.
(Off, 5, 10, 15, 20, .............., 55, 60 minutes).
• The Time keeper function can be set from 1 to 10 minutes at 1 minute intervals, and from 10 to 60 minutes al 5 minute intervals
(Off, 1, 2, 3, 4, .............., 8, 9, 10, 15, 20, 25, .............., 55, 60 minutes).
• You can use this function through the MENU button.
• Press the EXIT button to exit the menu screen.
25
Function
Using the Digital Zoom Function
*T
his function is available only in RGB input mode. The Zoom -/+ and Position values return to their default when you
change the SOURCE or input signal, or turn the power off.
Adjusting the Position
Adjusting the Zoom
1. Press the ZOOM button on the remote control.
1. Press the ZOOM button on the remote control.
2. Press the ∧,∨ button to select Zoom -/+ item.
2. Press the ∧,∨ button to select Position item.
Zoom -/+
Position
Reset
MENU Exit
<
ꕌ Move
ꕍ
100
%>
Zoom -/+
Position
Reset
<> Select
MENU Exit
<
% >
110
Press OK to Start
ꕌ Move
ꕍ
◉ OK
3. Press the <,> button to adjust Zoom -/+ to your 3.Press the ◉ OK button. When the window below
choice.
appears at the bottom right corner of the screen, press
the ∧,∨,<,> to adjust the position. When the arrow
• You can adjust Zoom -/+ in 5% increments from 100% to
turns black, maximum adjustment has been reached
250%.
and no further adjustment can be made.
• You can also use this function by using the MENU button.
• Press the EXIT button to exit the menu screen.
Prev.
• P
osition is activated only when Zoom -/+ is set to more than
105%.
• You can also use this function by using the MENU button.
• Press the EXIT button to exit the menu screen.
To make the project turn on when power is applied
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧, ∨ buttons to move to Auto Power and press the ◉OK
button.
3. Press the ∧, ∨ buttons to move to On and press the ◉OK button.
• On : Connecting power cord to the projector turns on the projector.
• Off : Connecting power cord to the projector makes the projector in standby
state.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Language
Aspect Ratio
Overscan
Flip horizontal
Flip vertical
Sleep time
Auto sleep
Presentation timer
Digital Zoom
Auto Power
MENU Prev.
26
<
English
>
<
4:3
>
<
10%
>
<
Off
>
<
60 Min
>
<
Off
>
ꕌ Move
ꕍ
◉ OK
Function
Using the keystone function
1. Press the KEYSTONE button on the remote control.
2. Press the <,> button to select a item.
Top right
Top left
Bottom left
Keystone
Bottom right
Top left
Top
Bottom
Right
Left
0
V
0
Background <
Signal
>
Keystone reset
3.Press the ∧,∨ button to select the item (H or V) you want, and press
the <,> button to adjust it.
• • • • H
MENU Exit
<> Select
You can adjust each item from 0 to 100.
The default value may change depending on input mode.
You can also use this function by using the MENU button.
Press the MENU button to exit the menu screen.
To select a background image
To initialize keystone
1. Press the KEYSTONE button on the remote control.
1. Press the KEYSTONE button on the remote control.
2. Please select a Background by ∧,∨ button.
2. Please select Keystone reset by ∧,∨ button.
3. Please select desiring item by <,> button.
3. Press the ◉ OK button. The Keystone will reset to the
factory setting.
• If there ’s no input signal,it is possible to adjust keystone by
using the adjusting pattern.
V
0
Background
V
<
Signal
Signal
>
Keystone reset
MENU Exit
<> Select
0
Background
<
Signal
Signal
Keystone reset
Press OK Key
MENU Exit
◉ OK
>
Using the Blank Function
*This function may be effective if you need to get the attention of the audience during presentations, meetings or briefings.
1.Press the BLANK button.
• The screen turns off to a background color.
• You can choose the background color. (Refer to ‘Selecting blank image’)
2.Press any button to cancel the blank function.
• To temporarily turn off the lamp, press BLANK on the remote control. Do not block the projection lens with
any objects when the projector is under operation as this could cause the objects to become heated and
deformed or even cause a fire.
27
Function
Selecting a Blank image
1. P
ress the MENU button and then use <, > button to select the
menu.
Keystone
Blank Image
Screen Capture
3. Press the <,> button to select the color you want to use.
Lamp mode
Monitor Out
• Background image will be altered to the selected Blank image function.
Communication
• You can choose blue, black, green, or captured image or logo for the Blank image.
Set ID
• If you have a captured image, you can use it as a blank image instead of logo
Network Setting
image. You can only use the last captured image.
High Altitude
• When you select the Captured image, it displays a logo if you don’t have a capLamp Time tured image.
2. Press the ∧,∨ button to select Blank image item.
• Press the MENU button twice or the EXIT button to exit the menu screen.
ꘀ Prev.
<
Black
>
<
High bright
>
<
RGB1
>
<
Serial
>
<
1
>
<
Auto
>
0 Hr
ꕌ Move
ꕍ
<> Select
Screen Capture Function
1.Press the MENU button and then use <, > button to select the
menu.
2.Press the ∧,∨ button to select Screen Capture item.
3.Press the ◉OK button to capture actual screen image.
Confirm Screen Capture
OK
Cancel
4. Press the ◉OK button again to save Screen capture image.
Keystone
Blank Image
Screen Capture
Lamp mode
Monitor Out
Communication
Set ID
Network Setting
High Altitude
Lamp Time
ꘀ Prev.
• Y
ou can use the captured image as a Blank image.
• You can not use the remote control when this function is in use.
• If you want see your captured image, select Captured image in the
Blank image function.
• Press the MENU button twice or the EXIT button to exit the menu
screen.
Lamp mode Function
1. Press the LAMP button of remote control.
2. Press the <, > button to adjust the screen condition as you want.
<
High Bright
>
<
Economic
>
• It will automatically change into power saving mode at a specific temperature (more than 37°C).
• You can use this function through the MENU button.
• To exit the menu display, press the EXIT button.
28
<
Black
>
To set
<
High bright
>
<
RGB1
>
<
Serial
>
<
1
>
<
Auto
>
0 Hr
ꕌ Move
ꕍ
<> Select
Function
Using the Monitor out Function
* You can select either of the two RGB inputs.
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select Monitor Out item.
3. Press the <,> button to select RGB1, RGB2 or Auto.
• Press the MENU button twice or the EXIT button to exit the menu screen.
• Auto mode is the mode to output an image of currently seeing input among RGB1 or RGB2 input.
Keystone
Blank Image
Screen Capture
Lamp mode
Monitor Out
Communication
Set ID
Network Setting
High Altitude
Lamp Time
ꘀ Prev.
<
Black
>
<
High bright
>
<
RGB1
>
<
Serial
>
<
1
>
<
Auto
>
0 Hr
ꕌ Move
ꕍ
<> Select
Communication setting
1. P
ress the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select Communication setting.
3. Press the <,> button to select Serial or Lan.
• Set communication to Lan to activate Network Setup.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Keystone
Blank Image
Screen Capture
Lamp mode
Monitor Out
Communication
Set ID
Network Setting
High Altitude
Lamp Time
ꘀ Prev.
<
Black
>
<
High bright
>
<
RGB1
>
<
Serial
>
<
1
>
<
Auto
>
0 Hr
ꕌ Move
ꕍ
<> Select
High Altitude Mode
*H
igh Altitude Mode is used when the usage environment is higher than 1200
meters.
1. Press the MENU button and then use <, > button to
select the
menu.
2. Press the ∧, ∨ buttons to move to High Altitude and press
the ◉OK button.
3. Press the <, > buttons to move to Yes and press the ◉OK
button.
High Altitude Mode is used when the environment is higher
than 4,000 feet. Do you want to turn the High Altitude Mode on?
Yes
Keystone
Blank Image
Screen Capture
Lamp mode
Monitor Out
Communication
Set ID
Network Setting
High Altitude
Lamp Time
ꘀ Prev.
<
Black
>
<
High bright
>
<
RGB1
>
<
Serial
>
<
1
>
<
Auto
>
To set
0 Hr
ꕌ Move
ꕍ
<> Select
No
• Press the MENU button twice or the EXIT button to exit the menu screen.
29
Function
Checking lamp time
1. P
ress the MENU button and then use <, > button to select the
menu.
Keystone
Blank Image
Screen Capture
2. You can check lamp usage hours
Lamp mode
Monitor Out
• Red warning lamp will light when it needs to be replaced. (Please refer page 10)
• When lamp usage hour exceeds the limit, red warning lamp is lit when the power Communication
is turned on.
Set ID
• Press the MENU button twice or the EXIT button to exit the menu screen
Network Setting
High Altitude
Lamp Time
Using Still Function
ꘀ Prev.
<
Black
>
<
High bright
>
<
RGB1
>
<
Serial
>
<
1
>
<
Auto
>
0 Hr
ꕌ Move
ꕍ
<> Select
1. Press the STILL button of remote control.
• You can freeze the input image.
<Moving Image>
<Still Image>
2.To exit STILL, press any button .
• The STILL function will release automatically after approximately 10 minutes.
Screen Menu Options
Auto configure Function
*Auto configure is the function that finds optimal video condition by automatically adjusting width and calibration of internal
signal of the projector and various graphic signal of PC in RGB mode.
*Auto configure operates only for RGB input.
1. Press the MENU button and then use <, > button to select the
menu.
2. Press the ∧,∨ button to select auto configure.
• It automatically configures the location of image and calibration.
3. In some cases, auto configure itself cannot find optimal video quality.
If it needs manual adjustment even after auto configure due to various PC mode
input, adjust using phase, clock, horizontal and vertical from the menu.
Auto Configure Phase
Clock
Horizontal
Vertical
ꘀ Prev.
8
0
0
0
ꕌ Move
ꕍ
hen executing auto configure during video playback of PC graphic signal, the projector may not be
W
able to find optimal video condition. Please execute auto configure in freeze frame.
30
◉ OK
Function
Using the Phase Function
1. Press the MENU button and then use <,> button to select the
menu.
2.Press the ∧,∨ button to select Phase item.
3.Press the <,> button to make desired adjustments.
• Phase adjustment range is 0 ~63.
• The variable range can be different depending on input resolutions.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Auto Configure Phase
Clock
Horizontal
Vertical
ꘀ Prev.
8
0
0
0
ꕌ Move
ꕍ
<> Adjust
8
0
0
0
ꕌ Move
ꕍ
<> Adjust
8
0
0
0
ꕌ Move
ꕍ
<> Adjust
8
0
0
0
ꕌ Move
ꕍ
<> Adjust
Using the Clock Function
1. Press the MENU button and then use <,> button to select the
menu.
2.Press the ∧,∨ button to select Clock item.
3.Press the <,> button to make desired adjustments.
• Clock adjustment range is -20 ~ 20.
• The variable range can be different depends on input resolutions.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Auto Configure Phase
Clock
Horizontal
Vertical
ꘀ Prev.
Using the Horizontal Function
1.Press the MENU button and then use <,> button to select the
menu.
2.Press the ∧,∨ button to select Horizontal item.
3.Press the <,> button to make desired adjustments.
• Horizontal adjustment range is -50 ~ 50.
• The variable range can be different depends on input resolutions.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Auto Configure Phase
Clock
Horizontal
Vertical
ꘀ Prev.
Using the Vertical Function
1.Press the MENU button and then use <,> button to select the
menu.
2.Press the ∧,∨ button to select Vertical item.
3.Press the <,> button to make desired adjustments.
• Vertical adjustment range is -25 ~ 25.
• The variable range can be different depends on input resolutions.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Auto Configure Phase
Clock
Horizontal
Vertical
ꘀ Prev.
31
Function
Serial communication function
* Connect the RS-232C input jack to an external control device (such as a computer) and control the Projector’s functions externally.
SET ID
1. Press the MENU button and then use <,> button to select the
menu.
2.Press the ◉ OK button and then use ∧,∨ button to select Set ID item.
3.Press the <,> button to select your desired number.
Press the ◉OK button to save the selected number.
• The adjustment range of Set ID is 1~99.
• Only the projector with the specified ID number will operate from the remote
control.
• Press the MENU button twice or the EXIT button to exit the menu screen.
Keystone
Blank Image
Screen Capture
Lamp mode
Monitor Out
Communication
Set ID
Network Setting
High Altitude
Lamp Time
ꘀ Prev.
To connect with serial communication
• Connect the serial port of the PC to the RS-232C jack on the projector back panel.
• RS-232C cable is not supplied with the projector.
• Use the RS232C cable to control the projector externally (Refer to Fig.1).
<Fig.1, RS-232 Interface Cable>
RXD
TXD
DTR
GND
DSR
RTS
CTS
RXD
TXD
DTR
2
3
4
5
6
7
8
2
3
4
5
6
7
8
PC
Projector
GND
DSR
RTS
CTS
* 1, 9 Pin No Connection
Communication Parameter Setup
• Baud Rate : 9600 bps(UART)
• Data Length : 8 bit
• Parity : none
• Stop bit : 1 bit
• Flow Control : none
• Communication code : ASCII code
32
9
5
6
1
<
Black
>
<
High bright
>
<
RGB1
>
<
Serial
>
<
1
>
<
Auto
>
0 Hr
ꕌ Move
ꕍ
◉ OK
Function
Command Reference List
Command 1
Command 2
Data
(Hexadecimal)
Real data mapping
01. Power
k
a
0~1
-
02. Aspect Ratio k
c
1 ~ 2, 5
-
03. Screen Mute
k
d
0~1
-
04.Contrast
k
g
0 ~ 64
1
05. Brightness
k
h
0 ~ 64
1
06.Color
k
i
0 ~ 64
1
07. Tint
k
j
0 ~ 64
2
08. Sharpness
k
k
0 ~ 64
1
09.OSD Select
k
l
0~1
-
10. Remote Control Lock / Key Lock
k
m
0~1
-
11. Color Temperature
k
u
0~2, 4
-
12. Red ADC gain adjustment j
w
0 ~ 64
1
13. Green ADC gain adjustment j
y
0 ~ 64
1
14. Blue ADC gain adjustment j
z
0 ~ 64
1
15. Lamp mode
n
p
0~1
-
16. Auto Configuration
j
u
1
-
17. Input Select
x
b
*
-
18. Key
m
c
Code des touches
-
* Refer to the detailed information for data with [*] mark.
Communication Protocol
* Real data mapping 1
* Real data mapping 2
33
Function
1. Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1] : First command to control the set.(k, j, x, ASCII code, 1 Character)
* [Command 2] : Second command to control the set..(ASCII code, 1 Character)
* [Set ID] : You can adjust the set ID to choose desired projector ID number in special menu. See previous page.
Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected projector set is controlled.
Refer to ‘Real data mapping 1’.
* [DATA]
: To transmit command data. Transmit 2 character when organized ASCII code.
* Transmit ‘FF’ data to read status of command.
* [Cr] : Carriage Return
ASCII code ‘0x0D’
* [ ] : ASCII code character correspond to “Space Bar” which is in order to classify command, set ID and Data.
2. OK Acknowledgement
[Command2] [ ] [Set ID] [ ] [OK] [Data] [x]
*The Projector transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
3. Error Acknowledgement
[Command2] [ ] [Set ID] [ ] [NG] [Data] [x]
*The Projector transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable
functions or communication errors.
Data : [1] :illegal code(This command is not supported.)
[2] :not support function(This function doesn’t work.)
[3] :wait and retry(Try again a few minute later.)
01. Power (Command:ka)
02. Aspect Ratio (Command:kc)
→ To control Power On/Off of the Projector.
→ To adjust the screen format.
Transmission
[k] [a] [ ] [Set ID] [ ] [Data] [Cr]
Data 0 : Power Off
1 : Power On
Ack
[a] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : Power Off
1 : Power On
→ To show Power On/Off status.
Transmission
[k] [c] [ ] [Set ID] [ ] [Data] [Cr]
Data1 : 4:3
2 : 16:9
5 : 15:10
Ack
[c] [ ] [Set ID] [ ] [OK] [Data] [x]
Data1 : 4:3
2 : 16:9
5 : 15:10
Transmission
[k] [a] [ ] [Set ID] [ ] [FF] [Cr]
Ack
[a] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : Power Off
1 : Power On
*In like manner, if other functions transmit ‘0xFF’ data based on this format, Acknowledgement data feed back presents status about each function.
03. Screen Mute (Command:kd)
→ To select screen mute on/off.
Transmission
[k] [d] [ ] [Set ID] [ ] [Data] [Cr]
Data 0 : Screen Mute Off (Picture On)
1 : Screen Mute On (Picture Off)
Ack
[d] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : Screen Mute Off (Picture On)
1 : Screen Mute On (Picture Off)
34
Function
04. Contrast (Command:kg)
09. OSD Select (Command:kl)
→To adjust screen contrast.
→ To select OSD On/Off.
Transmission
Transmission
[k] [g] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
*Refer to ‘Real data mapping 1’.
Ack
[g] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
[k] [ l ] [ ] [Set ID] [ ] [Data] [Cr]
Data 0 : OSD Select Mode Off
1 : OSD Select Mode On
Ack
[ l ] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : OSD Select Mode Off
1 : OSD Select Mode On
05. Brightness (Command:kh)
→ To adjust screen brightness.
Transmission
[k] [h] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
*Refer to ‘Real data mapping 1’.
Ack
[h] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
10. Remote Control Lock/Key Lock
(Command:km)
→To lock the front panel controls on the
projector and remote control.
Transmission
[k] [m] [ ] [Set ID] [ ] [Data] [Cr]
Data 0 : Lock Off
1 : Lock On
Ack
06. Color (Command:ki)
→ To adjust the screen color. (Video/Component)
Transmission
[k] [ i ] [ ] [Set ID] [ ] [Data] [Cr]
[m] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : Lock Off
1 : Lock On
* If you're not using the remote control, use this mode.
When main power is On/Off, external control lock is released.
Data Min : 0 ~ Max : 64
*Refer to ‘Real data mapping 1’.
Ack
[ i ] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
07. Tint (Command:kj)
→T
o adjust the screen tint.(Video/Component 60Hz or
NTSC signal)
Transmission
[k] [ j ] [ ] [Set ID] [ ] [Data] [Cr]
Data Red : 0 ~ Green : 64
* Refer to ‘Real data mapping2’.
Ack
[ j ] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Red : 0 ~ Green : 64
11. Color Temperature (Command:ku)
→A
djust the color temperature. But, color temperature cannot be
adjusted if video mode is set to bright or golf.
Transmission
[k] [u] [ ] [Set ID] [ ] [Data] [Cr]
Data 0 : Normal
1 : Cool
2:Warm
4 : Natural
Ack
[u] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : Normal
1 : Cool
2:Warm
4 : Natural
12. Red ADC gain Adjustment (Color R) (Command:jw)
→ Adjust the Red gain of ADC part.(RGB)
Transmission
08. Sharpness (Command:kk)
→ To adjust the screen sharpness.(Video/Component)
Transmission
[k] [k] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
[ j ] [w] [ ] [Set ID] [ ] [Data] [Cr]
Data
Min : 0 ~ Max : 64
*Refer to ‘Real data mapping 1’.
Ack
[w] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
Ack
[k] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
35
Function
13. Green ADC gain Adjustment (Color G)
(Command:jy)
→ Adjust the Green gain of ADC part.(RGB)
Transmission
[ j ] [y] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
*Refer to ‘Real data mapping 1’.
Ack
17. Input Select (Command:xb)
→ To select input source for the Set.
Transmission
[x] [b] [ ] [Set ID] [ ] [Data] [Cr]
Data
20 : Video
60 : RGB1
[b] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
14. Blue ADC gain Adjustment (Color B)
(Command:jz)
18. Key (Command:mc)
Transmission
[ j ] [z] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
*Refer to ‘Real data mapping 1’.
Ack
20 : Video
60 : RGB1
61 : RGB2
→ To send Key code of IR romote control.
Transmission
[m] [c] [ ] [Set ID] [ ] [Data] [Cr]
Data
Key code
Ack
[c] [ ] [Set ID] [ ] [OK] [Data] [x]
[z] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
Key code
15. Lamp Mode (Command:np)
→ To reduce the power consumption of the projector.
Transmission
[ n ] [p] [ ] [Set ID] [ ] [Data] [Cr]
Data 0 : Low Power Off
1 : Low Power On
Ack
[p] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : Low Power Off
1 : Low Power On
∧
∨
<
>
POWER
INPUT
MENU
EXIT
◉ OK
STILL
RATIO
BLANK
KEYSTONE
MODE
40
41
03
02
AD
EF
43
5B
44
BC
79
84
A4
4D
4F
16. Auto Configuration (Command:ju)
→ To adjust picture position and minimize image shaking automatically. It works only in RGB mode.
Transmission
[ j ] [u] [ ] [Set ID] [ ] [Data] [Cr]
Data 1 : To set
Ack
[u] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 1 : To set
36
90 : HDMI
Ack
[y] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
→ Adjust the Blue gain of ADC part.(RGB)
61 : RGB2
4E
ZOOM
LAMP
SLEEP
AUTO
FLIP V.
FLIP H.
5C
68
0E
92
96
97
90 : HDMI
Function
Network setting function
Using the network setting
*
This is the function that the user can remotely control projector using LAN
< Connection Method>
Connect LAN terminal of projector and that of the computer
s Automatic setting
< Method >
1. P
ress the MENU button and then use <,> button to select the
menu.
2. Press the ∧,∨ button to select Communication.
3. Press the <,> button to select LAN
4. Press the ∧,∨ button to select Network Setting.
5. Press the ∧,∨ button to select Auto.
Keystone
Blank Image
Screen Capture
Lamp mode
Monitor Out
Communication
Set ID
Network Setting
High Altitude
Lamp Time
ꘀ Prev.
<
Black
>
<
High bright
>
<
RGB1
>
<
LAN
>
<
1
>
<
Auto
>
0 Hr
<> Move
◉ OK
IP setting in progress, Please wait…
IP Address
1 9 2 . 1 6 8 . 0 0 0 . 0 0 5
Subnet Mask
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0
Gateway
1 9 2 . 1 6 8 . 0 0 0 . 0 0 1
IP setting is succeeded.
ꘀ Prev.
- Network setting is done automatically
37
Function
s Manual setting
< Method >
1. P
ress the MENU button and then use <,> button to select the
menu.
2. Press the ∧,∨ button to select Communication.
3. Press the <,> button to select LAN.
4. Press the ∧,∨ button to select Network Setting.
Keystone
Blank Image
Screen Capture
Lamp mode
Monitor Out
Communication
Set ID
Network Setting
High Altitude
Lamp Time
ꘀ Prev.
5. Press the <,> button to select Manual setting.
6. Set IP address of PC and set that of projector to be in the same width with PC.
Press the ∧,∨ button to change number, and the <,> to move to next category
IP Address
Subnet Mask
Gateway
PC
192.168.0.10
255.255.255.0
192.168.0.1
Projector
192.168.0.5
255.255.255.0
192.168.0.1
• Press menu button to go back.
IP Address
1
9
2
.
1
6
8
.
0
0
0
.
0
0
5
Subnet Mask
2
5
5
.
2
5
5
.
2
5
5
.
0
0
0
Gateway
1
9
2
.
1
6
8
.
0
0
0
.
0
0
1
Press OK Key
ꘀ Prev.
<> Move
ꕌ Adjust
ꕍ
7. P
ress ◉ confirm button after IP setting.
IP address is saved.
8. Network setting is done manually
IP setting in progress, Please wait…
IP setting is succeeded.
38
<
Black
>
<
High bright
>
<
RGB1
>
<
LAN
>
<
1
>
<
Manual
>
0 Hr
<> Move
◉ OK
Information
Information
Supported Monitor Display
*The following table lists the display formats supported by the projector.
Sources
• • • • Format
Vertical Freq.(Hz)
Horizontal Freq.(kHz)
If the projector does not support the input signal, “Out of Range” message appears on the screen.
The projector supports DDC1/2B Plug & Play function. (Auto recognition of PC monitor)
The Synchronization input form for horizontal and vertical frequencies are Separate.
Depending on the graphics card in the computer, some supported resolutions may not look optimal.
<DVD/DTV Input>
Signal
59.94 / 60Hz
50Hz
24/30Hz
Component-*1 HDMI(DTV)-*2
480i
O
X
480p
O
O
720p
O
O
1080i
O
O
576i
O
X
576p
O
O
720p
O
O
1080i
O
O
1080p
O
O
* Cable type
1- RCA to D-Sub Adapter
2- HDMI to HDMI Cable
39
Information
Replacing the Lamp
Lamp Replacement
<Front panel of the Projector>
The usable lifetime of the lamp depends on the environment it is used
in. You can see the amount of time the lamp has been used in the
CHECKING LAMP TIME section of the Menu (page.30). You must
replace the lamp when:
• The projected image gets darker or starts to deteriorate.
• The lamp indicator is red.
• The message “Replace the lamp” appears on the screen when
turning the projector on.
Lamp indicators
Be careful when replacing lamp
ꔈꔈ Press the POWER button on the control panel or remote control to turn off power.
ꔈꔈ If the operation indicator LED is orange and blinking, do not disconnect the main supply until the operation
indicator LED is lit up constantly (orange).
ꔈꔈ Allow the lamp to cool for 1 hour before replacing it.
ꔈꔈ Replace only with the same type lamp from an LG Electronics Service Center. Using another manufacturers
lamp may cause damage to the Projector and lamp.
ꔈꔈ Pull out the lamp only when replacing the lamp.
ꔈꔈ Keep the lamp unit out of reach of children. Keep the Lamp away from heat sources such as radiators, stoves
etc.
ꔈꔈ To reduce the risk of fire do not expose the lamp to liquids or foreign materials.
ꔈꔈ Do not place the lamp near any heat source.
ꔈꔈ Make sure the new lamp is securely tightened with screws. If not, the image may be dark or there could be an
increased risk of fire.
ꔈꔈ Never touch the lamp unit glass otherwise image quality may be compromised or lamp life maybe reduced.
To obtain a replacement Lamp unit
• L
amp model number is on page 43. Check the lamp model and then purchase it from an LG Electronics
Service Center.
• Using another manufacturers lamp may cause damage to the projector.
Lamp unit disposal
• Dispose of the used lamp by returning it to the LG Electronics Service Center.
40
Information
Open lamp cover to change lamp
1
Turn off the projector and pull the power plug from
the power outlet. Place the projector on table or
somewhere with a flat surface.
2
Loosen screws on the side using a screwdriver. Lift
up the lamp cover in the direction of the arrow.
Do not pull the cover in the vertical direction.
Press “A” if the lamp cover does not lift up.
Let the lamp cool for one hour before touching it.
Press here.
A
Lamp cover
fixing screw
3
4
Open lamp cover and loosen the two screws
holding the lamp in.
Pull the lamp handle from the sill.
Knob
Screw
5
6
Pull the lamp out slowly using the handle
attached to it.
Insert the new lamp case in carefully. Check if it is
inserted correctly. Check if “B” part is inserted
correctly and press “C” part again to verify the new
lamp is inserted completely.
Press here.
C
B
7
8
Replace the screws removed in step 3.
Close the lamp cover and replace the screws removed
in step 2.
The projector will not operate when the lamp cover is
open. A green warning lamp indicates the projector
will not start due to the cover being open.
Please use appropriate lamp for the model.
Projector might not be turned on if the lamp cover is not closed correctly after replacement. In this
case, please contact our service representative after checking if the lamp is fixed correctly.
To re-assemble lamp cover
1
Press the lamp cover against the
support line. Maintain a slope of
about 30°.
2
Do not push vertically. Push
diagonally to insert.
Do not apply unreasonable force to
the tab below during replacement
support
line.
Do not over-tighten the side screws.
tab
41
Information
Regarding the projector lamp control
WARNING
• Don’t turn off the projector until at least in 5 minutes after activating it.
- The frequent On/Off changes may cause the lamp function to deteriorate.
• Don’t pull out the power cord while the projector's cooling fan is on.
- It may cause the lamp life-span to shorten and get damaged.
• The life-span of projector depends on the use environment and treatment conditions.
• T
he projector uses a high pressure mercury lamp so that serious caution is essential. The shock or abuse while using may
cause lamp to blow off with explosion.
• When you continue to use the projector after an interval of lamp replacement, the lamp may be blown off with explosion.
• The following treatment should be done if the lamp shatters.
- Pull off the power cord immediately.
- Let some fresh air in immediately (Ventilation).
- Check the product condition at the nearer service center and replace the lamp, if necessary.
- Don’t try to disassemble the product.
How to attach the lens cap to the projector
How to attach the lens cap
1
3
42
Prepare the lens cap and the strap supplied as
accessories.
Attach the strap at the hole of the projector into
the hole of the lens cap, and then pass the lens
cap through the strap lasso.
2
Insert the non-knot end of the strap into the
hole at the bottom of the lens section of the
projector.
4
They are completely assembled as shown in
the below figure.
Information
Specifications
MODEL
BX403B (BX403B-JD) / BX503B (BX503B-JD)
Power
AC 100 - 240V~ 50/60Hz, BX403B : 3.8A/BX503B : 4.3A
Resolution
1024(Horizontal) x 768(Vertical)pixel
Horizontal / Vertical Ratio
4:3(horizontal:vertical)
DLP panel size(mm)
17.8
Screen size
(Projection distance)
Wide : 1.0 ~ 7.5m
Projection off-set ratio
100%
Remote control distance
12m
Tele : 1.2 ~ 8.7m
Zoom ratio
1:1.2
Video compatibility
NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N
Height(mm)
148.5 (with foot), 135.7(without foot)
Breadth(mm)
403.3
Length(mm)
293.1
Weight(kg)
BX403B : 5.9/BX503B : 6.2
Operating Condition
Projector Lamp
Temperature
Lamp model
In operation : 32~104°F(0°C~40°C)
In storage and transit : -4~140°F(-20°C~60°C)
BX403B : AJ-LDX5
BX503B : AJ-LBX5
Humidity
Lamp power consumption
In operation : 0 ~ 80% relative humidity by dry hygrometer
Not in operation : 0 ~ 85% relative humidity by dry hygrometer
BX403B : 300W
BX503B : 330W
43
The model and serial number of the projector is
located on the back or one side of the projector.
Record it below should you ever need service.
MODEL
SERIAL
Download PDF