LG | SC105-2D | LG SC105-2D Owner’s Manual

Owner's Manual
Laser Display Screen
Please read the safety information carefully before using the product.
SC105
P/NO : MFL67864905 (1307-REV01)
www.lg.com
2
Safety Precautions
Safety Precautions
Please take note of the safety instructions to prevent any potential accident or misuse
of the product.
yySafety precautions are given in two forms, i.e. Warning and Caution as detailed below.
WARNING: Failure to follow the instructions may cause serious injury and even
death.
CAUTION: Failure to follow the instructions may cause minor injury or damage to
the product.
yyRead the owner's manual carefully and keep it at hand.
Installation
WARNING
yyThe product should be installed by a
qualified professional specified by the
retail store.
- The product installation by a nonqualified personnel is dangerous
and may cause personal injury.
The
yy product should be installed
where its weight can be supported.
- Otherwise, the product may fall and
cause personal injury.
When
moving or replacing the
yy
product after installation, contact a
qualified installer specified by the
retail store.
- If an unqualified person moves and
installs the product, this may cause
safety issues as this task requires
the special technique.
Do
yy not hang on the product or apply
shock to the product.
- The product may fall and cause
injury.
CAUTION
yyFollow the instructions in the manual
to install the product.
- Otherwise, it may cause serious
injury or damage to the product.
yyWhen installing the product or
adjusting the height of the product,
two or more people are needed.
- If you do it by yourself, you may
drop the product causing personal
injury or damage to the product.
yyWhen installing the product, check
whether the wall is strong enough to
hold the product and use the
anchors and screws provided.
- Otherwise, the product could fall
causing safety issues.
Safety Precautions
CAUTION
yyWhen drilling the holes in the wall,
make sure you use a drill and a drill
bit with the specified size of diameter.
Ensure that you also follow the
instructions regarding the depth of
the holes.
- Otherwise, the product may be
installed improperly causing safety
issues.
yyDo not clean the product with wet
towels, and do not use a heater or
humidifier underneath the product.
- Moisture permeating into the
product, steam or heat may result in
fire, electric shock or damage to the
product.
yyKeep the product away from sprinklers, sensors, high-tension wires
and power sources. Do not install the
product in a location where vibrations
or shock impacts are likely to occur.
yyWear working gloves when installing
the product. Do not use bare hands.
- Otherwise, it may cause personal
injury.
yyDo not place the product where it is
directly exposed to the light.
- The image may look dark due to
the light.
3
4
PREPARATION
PREPARATION
Accessories
Check the accessories provided with the product.
The picture may be different from the actual product.
Accessories are subject to change without prior notice in order to improve the performance of the product. New accessories may be added or old ones may be removed.
Up
Down
8 anchors for
attaching rings
(Ф8)
Tape 6 EA
18 Steel Spacers
8 bolts for attaching
rings (Ф8)
1 sheet of warp
correction sponge
Magnet 15 EA
2 Rings
1 warp correction ring
Preparations
Drill (M6, M8), leveler, tapeline, driver, tape
Paper template
1 piece of tape to
attach the paper
template
Safety lock pin
2 EA
Thread
Installation
Installation
Fixing the Anchor, Screw
CAUTION
yyCheck the material of the wall and the thickness of the finishing.
yyUse the anchors for wall material of concrete, light concrete, strong natural
stone, soft natural stone masonry
yy brick and hallow block that do not crack.
yyWhen installing the product on wall material not designated, install the
product so that each fixated location can withstand the pull out load of 70
kgf (686 N) and shear load of 100 kgf (980 N) or above.
a. Use a drill bit Ø8 mm to drill a hole for the anchor location within a depth of
80 mm - 100 mm.
b. Clean the drilled hole.
c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the
angle adjusting part to face upward.
Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at torque
of 45 kgf/cm - 60 kgf/cm.
a
b
Anchor
c
Ring and Space steel fixing screw
d
5
6
Installation
Installation STep
1 Attach a paper screen to the place where the screen will be located. (The paper
screen helps to easily install the adjustable bracket and bore holes in the wall.)
2 Two people lift the screen up until its bottom edge is level to the magnets at the
bottom of the paper screen. Put the screen close to the wall aligning with the locations marked with the tapes and hang the brackets on the rings by carefully pulling
it down.
CAUTION
yyAlign the top of screen with the top of the tape and the left and right sides of
the screen with the tape. Hang the bracket on the rings by lowering the screen
carefully. If the screen is upside down, the screen will be dark and no image will
be displayed.
Installation
<Ceiling type> 
Tape
Down
Up
Magnet
7
Down
Up
8
Installation
<Stand type>

Tape
Up
Down
Magnet
Up
Down
Installation
CAUTION
yyIf the screen is tilted when pulling it down, the screen may not fix to the bracket
and result in damage to the screen.
3 Move the screen in all directions to check whether the screen is securely hung on
the rings.
9
10
SPECIFICATIONS
SPECIFICATIONS
2245
2030
142
1272
147
1073
Model
SC105
Width (mm)
2245 ± 5 mm
Height (mm)
1272 ± 3 mm
Frame Height (mm)
12.0 ± 1.0 mm
Depth (mm)
9.1 ± 0.2 mm
Weight (kg)
32.30 kg
Download PDF