LG | GN-450USL | LG GN-450USL Owner’s Manual

Please read carefully the manual instruction and safety caution
before operating your refrigerator and retain it for future reference
P/No. : MFL68083701
Table of Contents
Important Safety Instruction
Identification of Parts
Temperature Control
Hygiene Fresh
Express Freezing
Eco Friendly
Self Test
Door Alarm
Ice Making
Suggestion On
Food storage
Care and
Water Dispenser
Foldable Shelf
Pull Out Tray
Lamp Replacement
Storing Food
Suggestion for energy saving
General Information
Smart Diagnosis™2
Trouble Shooting
It is normal....
Important Safety Instruction
Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recommended by the manufacturer.
Do not damage the sealed system or any piping in or within the refrigerator.
Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
The refrigerant and insulation blowing gas used in the appliance require
special disposal procedures. When disposal, please consult with service
agent or a similarly qualified person.
This appliance contains a small amount of isobutane refrigerant (R600a),
natural gas with high environmental compatibility, but it is also combustible.
When transporting and installing the appliance, care should be taken to
ensure that no parts of the refrigerating circuit are damaged. Refrigerant
squirting out of the pipes could ignite or cause an eye injury. If a leak is
detected, avoid any naked flames or potential sources of ignition and air the
room in which the appliance is standing for several minutes.
In order to avoid the creation of a flammable gas air mixture if a leak in the
refrigerating circuit occurs, the size of the room in which the appliance may be
sited depends on the amount of refrigerant used. The room must be 1m2 in size
for every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in
your particular appliance is shown on the identification plate inside the appliance.
Never start up an appliance showing any signs of damage. If in doubt, consult your
This guide contains many important safety messages.
Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you
of hazards that can cause death or serious injury you or others or cause damage
to the product. All safety messages will be preceded by the safety alert symbol and
the hazard signal word WARNING, or CAUTION. These words mean:
Death, or serious injury can occur if you don’t follow
Indicates an imminently hazardous situation which, if not
avoided, may result in minor or moderate injury, or product
damage only.
All safety messages will identify the hazard, tell you how to reduce the chance of
injury, and tell you what can happen if the instructions are not followed.
To reduce the risk of fire, electric shock, or injury to persons when using your
product, basic safety precautions should be followed, including the following.
Read all instructions before using this appliance.
1. When connecting the power
A dedicated outlet should be used.
• Using several devices at one outlet may cause fire.
• If unit is connected to an earth leakage breaker it may trip
resulting in spoiled food. This could occur due to power
supply circumstances, and may not necessarily mean a
refrigerator malfunction.
Do not allow the power plug to face upward or to be
crushed at the back of the refrigerator.
If the cord is crushed behind the refrigerator it may damage
the cable resulting in fire. An upward facing plug may pull
loose under the weight of the cord resulting in electrical failure
causing fire or the refrigerator turning off and spoiling food.
Prevent the power cord from being crushed or kinked if the refrigerator is
pushed in after the power plug is extracted during the installation.
When moving your appliance away from the wall, be careful not to roll over the
power cord or to damage it in any way.
Crushed or kinked cables can become the cause of fire or electric shock.
Do not allow heavy objects to kink or crush the power
It may damage the power cord and become a cause of fire or
electric shock.
Do not extend or modify the length of the power plug.
This may become the cause of fire or electric shock.
Unplug the power plug when cleaning, handling or
replacing the interior lamp of the refrigerator.
If the interior lighting is LED type, then it cannot be changed
by the user. Please call an authorised Service provider or
the manufacturer.
• Not doing so may cause electric shock or injury.
Do not pull out the cord or touch the power plug with wet
It may cause electric shock or injury.
Remove water or dust from the power plug and insert it
with the ends of the pins securely connected.
Dust, water or an unstable connection may cause fire or
electric shock.
Unplug the power cord from the power outlet for cleaning or other
Not doing so may cause electric shock or injury.
Do not disconnect by pulling on the cord. Always
disconnect by grasping and pulling on the plug top.
Pulling on the cable may damage the cable resulting in electric
shock or fire.
Make sure of grounding.
Consult a qualified electrician or service person if the
grounding instructions are not completely understood,
or if you have doubts on whether the appliance is
properly grounded.
Incorrect grounding may lead to electric shock in the event
of a breakdown.
Always have unit grounded in accordance with local regulations.
Be sure to use a properly grounded extension lead if an extension lead must be
If incorrectly grounded it may become the cause of a fire.
When the power cord or the power plug is damaged or
the power outlet is loose or damaged, do not plug the
power cord into the power outlet.
Doing so may cause electric shock or be the cause of a fire.
If the mains plug is removed from the wall outlet for any
reason, wait for 5 minutes or longer before reconnecting
the plug.
Not doing so may cause the operation of the refrigerator to fail.
If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
More than
30 inches
2. When using the refrigerator
Do not place heavy objects or liquid filled objects on the
top of the refrigerator.
Heavy objects may fall when opening and closing doors
resulting in injury. Liquid filled objects may leak or fall and break
resulting in injury, or electric shock.
Do not install the refrigerator in a damp or wet environment.
Moisture may penetrate electrical components resulting in fire or
electric shock.
This refrigerator is intended for normal domestic indoor use. It must not be
used outdoors, or stored in an out door location that is exposed to any
weathering conditions.
Do not lean on or hang from the doors or shelves of the
This will damage the doors and shelves of the refrigerator or
cause it to topple over resulting in serious injury and damage.
Always supervise children when they are near the refrigerator.
Never Allow children to enter or play inside the
compartments of the product.
It may endanger the life of a child if the child enters the
Take care when opening and closing the refrigerator doors. Vigorous opening
or closing may cause the contents to topple out resulting in injury or damage.
It is normal for the Freezer door to open if the refrigerator door is closed with
excessive force.
Do not store medical supplies, temperature critical
medicines, or scientific materials in the refrigerator.
If materials with strict temperature restrictions are stored they
may deteriorate or react undesirably resulting in possible harm
or risk.
The Academic
The Me
Do not use or place heated or flame based scented
products (Such as scented candles or incent burners) in or
on the fridge to deodorise.
It may become the cause of an explosion or fire.
Do not store or use Inflammable materials in or
around the refrigerator.
It may become the cause of an explosion or fire.
Do not use any combustible spray near the refrigerator.
It may become the cause of an explosion or fire.
Install in places away from the heat sources such as
fireplaces, heaters and ovens. Pay particular attention
to avoid locating near gas related products.
Not doing so may become the cause of an explosion or fire.
Do not place flower vases, cups, cosmetics, medicine or
any container with water on the refrigerator.
They may fall, leak or spill resulting in possible electric shock
or fire.
In case of a heavy electrical storm or if unit is not to be
used for a long period of time, disconnect the power plug.
There is a possibility of electrical damage. This may lead to an
electric shock or fire.
DO NOT use a water damaged unit until it has been
certified safe by a licensed electrician or similarly qualified
It may cause an electric shock or fire.
If a gas leak is detected, do not touch the refrigerator
or the outlet and ventilate the room immediately.
• Any spark my result in an explosion or fire.
• Because this refrigerator uses natural gas (isobutene,
R600a) as the environment-friendly refrigerant, even a
small amount (80~90g) is combustible. If a gas leak occurs
due to severe damage during delivery, installation or a
sealed system malfunction, a spark may cause a fire.
When any strange smell or smoke is detected from the
refrigerator, disconnect the power plug immediately
and contact to the service center.
Continuing to run unit may result in damage or fire.
Do not allow any person except a qualified engineer to
disassemble, repair the refrigerator.
It may cause injury, electric shock or fire.
Do not use the fridge-freezer for non-domestic purposes
(storing medicine or testing material, or for use in a mobile
application or for commercial or purposes.)
It may cause an unexpected risk such as fire, electric shock,
deterioration of stored material or chemical reaction.
When disposing the refrigerator, remove the door seals
from the refrigerator but leave the shelves in place so that
children may not easily climb inside.
Failure to do so may cause a child to become trapped inside.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
Install the refrigerator on a solid and level floor.
Installing it in an unstable place may cause death or serious injury
by the refrigerator falling over when opening or closing the door.
Do not insert hands or a metal object into the exit of
cool air, the cover, the bottom of the refrigerator, the
heatproof grill (exhaust hole) at the back.
It may cause electric shock or injury.
Do not spray water on either the inside or outside of the
refrigerator. Do not use alcohol or mineral based cleaners
on the refrigerator (such as Benzene or Thinners).
These may deteriorate or penetrate the insulation or electrical
components resulting in possible electric shock, fire or
damage to refrigerator.
Ensure that all foods and containers are stored or stacked in a stable manner.
A container may fall during opening and closing of the door of the refrigerator and
cause injury or breakages.
Do not put filled bottles in the freezer.
This will freeze the contents and break the bottle possibly
resulting in injury.
Do not insert hands into the bottom of the refrigerator.
The iron plate at the bottom may cause injury.
Carry the fridge-freezer with the handles at the bottom of the front and the top
of the rear.
Otherwise, your hands may slip possibly resulting in injury or
product damage. Because the product is heavy, carrying it
will require more than one person in order to avoid any
possible injury.
Opening and closing the door of the refrigerator vigorously may cause
the stored food in the refrigerator door baskets to fall and break and cause injury
so take care when opening and closing the doors.
Identification of Parts
Model Name : GN-*450***
Hygiene Fresh
Basket Door
Removable Glass Shelf
Foldable Shelf
Water Tank
Pull Out Tray
Basket Door
EZ Open Handle
Twist Ice Tray
Ice Bank
Freezer Drawer
Leveling Screw
If you find some parts missing from your unit, they may be parts only used in other models.
Appliance usage range
This appliance is intended to be used in household
and similar applications such as:
· staff kitchen areas, offices and other
domestic type environments.
· hotels, motels and other residential type
· bed and breakfast type environments;
1. Select a good location.
Place your fridge-freezer where it is easy to use.
2. Avoid placing the unit near heat sources, direct
sunlight or moisture.
Do not place in any outdoor sheltered location
or where it can be exposed to environmental
3. To ensure proper air circulation around the
fridge-freezer, please maintain sufficient space
on both the sides as well as top and maintain at
least 2 inches (5 cm) from the rear wall.
When your refrigerator is installed, allow it 3-4
hours to stabilize at normal operating temperature
prior to filling it with fresh or frozen foods.
If power plug is disconnected, allow 5 minutes
delay before restarting.
Your refrigerator is now ready for use.
Do not move refrigerator while the refrigerator
is operating.
Compressor may emit a temporary rattling noise.
(This is normal and will not impact on the
performance or the life of the compressor.
The rattling will stop, if the rattling sound does
not stop after 1 minute, turn off the power, wait
5 minutes and then turn back on again.
4. To avoid vibration, the unit must be leveled.
If required, adjust the leveling screws to
compensate for the uneven floor.
The front should be slightly higher than the rear
to aid in door closing.
Leveling screws can be turned easily by tipping
the cabinet slightly.
Turn the leveling screws counterclockwise (
to raise the unit, clockwise (
) to lower it.
5. Clean your fridge-freezer thoroughly and wipe
off all dust dust which may have accumulated
during shipping.
Climate class
The appliance is designed to operate at the limited
range of ambient temperature, depending on
climate zones. Do not use the appliance at the
temperature out of the limit. Climate class of your
appliance is indicated on the label with technical
description inside the fridge compartment.
6. Install accessories such as ice cube box, etc., in
their proper places. They are packed together to
prevent possible damage during shipment.
7. Connect the power supply cord (or plug) to the
outlet. Don't double up with other appliances
on the same outlet.
Ambient temperature
range °C
+10 ~ +32
+16 ~ +32
+16 ~ +38
+16 ~ +43
Temperature Control
Your refrigerator has controls that let you regulate the temperature in the refrigerator and freezer
Display Panel For Temperature Control
Adjusting the temperatures and functions
< Exterior Type >
Temperature Adjustment Button
for Refrigerator Compartment
Temperature Adjustment Button
for Freezer Compartment
Hygiene Fresh (Optional)
Express Freezing
Eco Friendly
Door Alarm
(Type A)
(Type B)
< Interior Type >
Door Alarm Express Temperature
Freezing Adjustment
Button for
Temperature Eco Friendly On/Off
Button for
See detailed button description on page 13~14
How to adjust the temperature in the
refrigerator compartment
Hygiene Fresh
• The initial target temperature of the refrigerator
and freezer Compartment is 3°C and -20°C
You can now adjust the target temperature of the
compartments as you wish.
• The Hygiene Fresh function has three modes,
Auto (default mode when icon is lit up) Power
mode (when icon and Power are lit up) and
Off (icon is not lit up). Power mode can be
engage by pressing the Hygiene Fresh touch
control respectively
< Exterior Type >
Power mode will resume back to Auto mode
after 4 hours.
Express Freezing.
• Please select this function for prompt freezing.
• This function is used when you want to freeze
the foods quickly. Press the Express Frezing
button once, and then the quick freeze operation
starts with the lamp on.
• The Express Freezing operation takes about
24 hrs. When its operation ends, it automatically
returns to the previous temperature setting.
If you want to stop the quick freeze operation
manually, press the Express Freezing button
once more, the lamp goes out, and the Express
Frezing operation stops and the refrigerator
returns to the previous temperature setting.
< Interior Type >
When the button is pressed, the temperature of
the refrigerator is 3°C 2°C 1°C 7°C 6°C
5°C 4°C 3°C sequentially.
When the button is pressed, the temperature of
the freezer is -20°C -21°C -22°C -23°C
-15°C -16°C -17°C -18°C -19°C -20°C
• The Express Freeze indicator remains on after
flashing 4 times when the Express Freezing
function is selected.
The actual inner temperature varies depending
on the food status, as the indicated setting
temperature is a target temperature, not actual
temperature within refrigerator.
Refrigeration temperature stability may fluctuate
initially. Please adjust temperature as above
after using refrigerator for minimum 2~3 days.
Eco Friendly
• This function makes the refrigerator work in a
power saving mode which is useful for when you
are away on holiday, by reducing energy
Pressing ‘ECO FRIENDLY’ starts the operation
and turns the lamp on and pressing it again
stops the operation.
For LED Model
• Pressing this button stops the operation of other
• ”Locking” or “Un-Locking” is repeated
whenever pressing the LOCK button.
(For “Locking” press the “LOCK” button for
3 secs.
For “Un-Locking” press the “LOCK” button for
3 secs.)
• When ‘LOCK’ is activated, all other buttons will not
When the Eco Friendly mode is “ON”, the other
buttons will not operate.To cancel the Eco
Friendly mode, press the Eco Friendly button
off so that the other buttons work and the
refrigerator returns to the previous temperature
• Pressing this button turns the refrigerator power
ON or OFF.
• ON or OFF is repeated whenever pressing the
ON/OFF button.
(For “OFF” press the “ON/OFF” button for
3~7 secs.
For “ON” press the “ON/OFF” button for 1 sec.)
• This function automatically detects certain
malfunctions when the refrigerator is in use.
• When a malfunction occurs, the temperature
display locks out and cannot be changed. Do
not turn off the power. Call your nearest
service provider so that they can diagnose
the display indicators. If the power is turned
off the error message will be reset and may
be difficult to properly diagnose.
This button does not isolate the mains power from
the refrigerator.
Door Alarm
• When the doors of the refrigerator are opened for a
while, the alarm sounds.
Please contact with the local service center if
warning continue to sound even after closing the
• The door alarm can be muted by pressing the Alarm
Self Test
Ice Making
• Take out the twist ice maker, fill it up and put it
back to it’s original location.
• Defrosting takes place automatically.
• The defrosting water flows down to the
evaporating tray and is evaporated automatically.
How to separate the vegetable drawer
• Ice is dropped into the ice
storage bin by rotating the Ice
separation handle on the ice
making compartment.
• You can make ice or use this
space as a storage space for
Frozen food. Removing (1)
(Twist ice maker) as shown in
the picture.
Remove the lower basket from the door by lifting it
Pull the drawer until it stops and while slightly lifting it
up, pull it further to remove it completely.
• Rotating the ice separation handle before ice
is fully frozen may cause the remaining water
to drop into the ice storage bin and lump
the ice together.
• Never pour water into the ice storage bin for
the intension of freezing it as it can break the
ice storage bin.
• When the ice storage bin is full, it is designed
for the ice to fall to the bottom in case is
overfilled . Be careful not to overfill
the storage bin.
• Gently remove the ice storage bin when
accessing ice so that the slide stopper is not
Water Dispenser (Optional)
1. Press the dispenser pad with a cup.
2. Water will be dispensed for as long as the
pad is pressed.
3. If slowly removing a cup from the pad, water
will not fall down.
4. Some noise after dispensing is the sound to
absorb water remained in the tube, which is for
the purpose of sanitation.
Cap Cover
Water Tank
Do not fill with other beverages (milk, juice,
carbonated beverage etc) other than drinkable
Filling of WATER TANK
How to Remove the Water Tank
Fill with drinkable water only.
Pump can generate some noise, while the cool
water is dispensed from the tank.
• Refitting is done in reverse to removal
• Be careful not to press on the dispensing valve.
• When refitting the tank to the door, ensure
that it is properly secured in its place.
When dispensing problem occurs, re-install water
bottle securely.
The dispenser pad should be firmly pressed
when dispensing water.
1. Pull out the water tank.
Then open the cap cover.
2. Up to 2.3 liters of water can be added.
3. Only fill with drinkable water. Never fill with
any other liquid other than water. Never pour
hot water into the tank.
Foldable Shelf (Optional)
How to remove the Folding Shelf.
You can fold the foldable shelf if you need to
accommodate taller containers or products on
the shelf underneath.
1. Slightly lift up the shelf and slide it inward.
2. Lift up the tucked shelf towards the rear wall.
3. You can simply pull the folded shelf in reverse
procedure to return it to the extended position.
Fold the Folding Shelf. Then lift it up slowly.
Make sure the folding shelf is securely restored
to the shelf position before placing items upon it.
Caution should be taken when adjusting the
shelf as it can fall out if not handled correctly.
Do not lift up the rear part of the Folding Shelf.
Pull Out Tray (Optional)
How to remove the Pull Out Tray
The pull out tray offers easy access to the rear
of the food drawer by sliding the tray out.
Fully extend the Pull-Out-Tray and lift the front
then pull it out slowly.
Apply caution when pulling out the tray so
that items do not fall off. Remove all food items
from on the tray first before removing it.
Please do not hold the bottom of the tray
when slide the tray in, as it could catch
your hand.
Lamp Replacement
This product uses LED Lamps which can not
be replaced by the user.
Please contact an authorized service center for
LED lamp service or replacement.
Suggestions on food storage
Suggestion for energy saving
Storing Food
• Do not store food which spoils easily at low
temperature, such as banana, and melon.
• Please do not keep the door open for a long
period of time.
• Allow hot food to cool prior to storing. Placing
hot food in the refrigerator could spoil other
food, and lead to higher electricity bills.
• Do not over load the shelves and drawers with
food as this will compromise the air flow and
cause the refrigerator to run for longer periods.
• When storing the food, use a container with a
lid. This prevents moisture from evaporating, and
helps food to keep its taste and nutrients.
• Do not set the temperature of refrigerator
lower than needed. Do not put the food near the
temperature sensor. Keep a distance of at least
5cm from the sensors.
• Allow hot food to cool prior to storing. Placing
hot food in the refrigerator could spoil other
food, and lead to higher electricity bills.
• Do not block air vents with food. Smooth
circulation of cold air keeps refrigerator
temperature even.
• Do not open the door frequently. Opening the
door lets warm air enter the refrigerator, and
cause temperature to rise.
• Do not block air vents with food. Smooth
circulation of cold air keeps refrigerator
temperatures even.
• Never keep too many foods in the door baskets,
as this may stop the door from fully closing.
• Do not open the door frequently. Opening the
door lets warm air enter the refrigerator, and
cause internal temperatures to rise.
• Do not store bottles in the freezer compartmentthey may break when frozen and cause injury.
• Arrange food items so that frequently used
items are placed toward the front of the shelves
or drawers.
• Do not refreeze food that has been thawed. This
causes loss of taste and nutrition.
• Do not store pharmaceutical products, scientific
materials or other temperature sensitive products
in the refrigerator.
Products that require strict temperature controls
must not be stored in the refrigerator.
• If you want to quick freeze new food, place it in
the middle drawer of freezer compartment, and
then press the Express Freezing button.
• To ensure good air circulation in the appliance,
push in the freezer drawers all the way.
Care and Maintenance
General Information
Vacation time
• During average length vacations, you will probably
find it best to leave the refrigerator in operation.
Place freezable items in freezer for longer life.
When you plan not to use the appliance, remove
all food,disconnect the power cord, clean
the interior thoroughly, and leave each door
OPEN to prevent odor formation.
Power Failure
• A 1 to 2 hour power failure will not significantly
disrupt the internal temperature. Try to avoid
opening and closing the door too frequently
so that the temperatures remain as stable
as possible until the power is restored.
If You Move
• Take out all food from the refrigerator and firmly
fix loose items with tape.
• Turn the leveling screws until they stop before
moving the refrigerator. Otherwise they
may scratch the floor and cause the refrigerator
not to move.
Anti Condensation Pipe
• The Anti-Condensation pipe is installed around
the front side of refrigerator and
freezer, as well as on the partition Anti-Condensation
between refrigerator compartment
and freezer compartment to
prevent dew and condensation.
• Especially after installation or
when ambient temperatures are
high, the refrigerator may feel hot on the front
and side surfaces, which is quite normal.
Care and Maintenance
Before Cleaning
Removing the Water Tank
Be sure to unplug the power before cleaning
or vacuuming any exterior surface or covers.
1. Lift up the release lever and pull out the water
tank assembly.
2. The water tank can be washed when removed
from the refrigerator by using neutral cleansing
Clean the outside of the refrigerator with a soft
cloth soaked with hot water or liquid detergent.
If you use a detergent, be sure to wipe it with a
clean wet cloth.
Cleaning the Water Tank and filling lid
The water tank lid and filling cap should be
cleaned periodically after being removed
from the water tank. A small brush such as a
toothbrush can be used to clean the grooved
part of the filling cap.
Same as above.
After Cleaning
Check that the power cord is not damaged, power
plug has not overheated, and that the power plug
is properly inserted into the outlet.
Do not separate the water tube from the Water
Tank lid when cleaning.
Be sure to dry the appliance with a cloth after
washing it with water.
Do not use abrasive, petroleum, benzene,
thinner, hydrochloride acid, boiling water, rough
brushes or scourers, etc, as they may damage
parts of the refrigerator.
Water Dispenser Drip Tray
Wipe moisture out around the door part and the
drip tray using a clean cloth.
Water Dispenser
Wipe moisture from the dispenser area and on the
dispenser pad using a cloth.
Care and Maintenance
Care and Maintenance
Smart Diagnosis™
Should you experience any problems with your
refrigerator, it has the capability of transmitting
data via your telephone to the LG service center.
This gives you the capability of speaking directly
to our trained specialists. The specialist records
the data transmitted from your machine and
uses it to analyze the issue, providing a fast
and effective diagnosis.
If you experience problems with your refrigerator,
call to the LG service center.
Only use the Smart Diagnosis feature when
instructed to do so by the LG call center agent.
The transmission sounds that you will hear are
normal and sound similar to a fax machine.
4. Hold the phone in the position until the end
of the sound data transfer.
5. Keep the phone in place until the tone
transmission has finished. This takes about
3 to 6 seconds
Resume your conversation with the consultant,
who will then be able to assist you in using
the information transmitted for analysis.
Smart Diagnosis cannot be activated unless your
refrigerator is connected to power.
If your refrigerator is unable to turn on, then
troubleshooting must be done without using
Smart Diagnosis.
• For best results, do not move the phone while
the tones are being transmitted.
• If the call center agent is not able to get an
accurate recording of the data, you may be
asked to try again.
• Call quality differences by region may affect
the function.
• Use the home telephone land line for better
communication strength and signal clarity.
• Poor signal quality may result in poor data
transmission from your phone to the machine,
which could cause Smart Diagnosis to not work
First, call to the LG service center. Only use the
Smart Diagnosis feature when instructed to do
so by the LG call center agent.
1. Open the refrigerator door.
3 sec.
2. Press and Hold the ‘Freezer’
button for 3 seconds.
If the door has been opened for over one minute,
you must close the door and start again from step 1.
3. Following the instructions of the operator,.hold
the phone's microphone close to the icon
Care and Maintenance
Trouble Shooting
Before calling for service, check this list. It may save you both time and expense.
This list includes common occurrences that are not the result of defective workmanship or
materials in this appliance.
Possible Causes
does not operate
Refrigerator or Freezer
Temperature too
Vibration or
Rattling or
Abnormal Noise
• Power plug may be unplugged from the power outlet.
Plug it in securely.
• House fuse has blown or circuit breaker has tripped.
Check and/or replace fuse and reset circuit breaker.
• Power cut.
Check house lights and other appliances.
• Temperature control not set on proper position.
Refer to Temperature Control section.
• Appliance is placed close to a heat source.
• Warm weather-frequent door openings.
• Door left open for a long time.
• Package holding door open or blocking air duct in freezer
• The floor on which the refrigerator is installed may be uneven or
the refrigerator may be unstable.
Make it even by rotating the leveling feet.
• Unnecessary objects placed in the back side of the refrigerator.
Frost or Ice
Crystals on frozen
• Door may have been left ajar or package holding door open.
• Too frequent or too long door openings.
• Frost within food packaging can be normal.
Moisture forms on
Cabinet Surface
• This phenomenon is likely to occur in a wet or humid environment.
Wipe it with a dry towel.
Moisture collects
Refrigerator has odor
• Too frequent or too long door openings.
• In humid weather, air carries moisture into refrigerator when doors are opened.
• Foods with strong odors should be tightly covered or wrapped.
• Check for spoiled food.
• Interior needs cleaning.
Refer to CLEANING section.
Care and Maintenance
Door not closing
Interior light does
not work
No water dispensing
• Food package is keeping door open.
Move packages that keep door from closing.
• Refrigeratorr is not level.
Adjust the leveling feet.
• The floor on which the refrigerator is installed may be uneven or
the refrigerator may be unstable.
Slightly raise the front side of the refrigerator by turning the leveling feet
• No power at outlet.
• If the LED lamp does not function, you must contact an authorised service
provider or the manufacturer.
• Water level is too low in Water Tank.
Fill the Water Tank with water. (Approx. 2.3 Lt capacity)
1. When this crossed-out wheeled bin symbol is attached to a product it means the
product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your
city office, waste disposal service or the shop where you purchased the product.
Care and maintenance
It is normal...
The following occurrences are normal.
When you hear "Tak" or
"Took" sound
This is the sound of various parts expanding/contracting
or various control devices operating depending on the
temperature change within the refrigerator.
When you hear
"Deureureuk~", "Dulkuk" or
"Woong" sound
This is the compressor or fan operating when the
operation of the refrigerator is starting or ending. This is
the same phenomenon of the sound generated when
starting or turning off the engine of a car.
When you hear "Kureureuk"
sound of water flowing
This is the sound of refrigerant changing the condition in
the freezer/refrigerator. When the liquid changes to gas,
you will hear the sound of water flowing and when gas
changes to liquid, you will hear the "Kureureuk" sound.
When you hear the sound of
wind such as "Shoo~" or
"Shik" right after you close
the door
This is the sound generated when the internal pressure is
temporarily lowered when the warm air entered through
the refrigerator or freezer is rapidly cooled.
When you hear a
vibrating sound
If the refrigerator is installed on wooden floor or wooden
wall, or if the refrigerator is not leveled properly, the
sound can be loud from the vibration.
When you hear a loud
sound after installing the
product for the first time
When you operate the refrigerator for the first time, the
refrigerator will operate at high speed to cool fast and the
sound can seem louder. When the internal temperature
falls below a certain level, the noise will subside.
Door open
When the door is slightly
opened after closing the
Depending on the force or speed of closing the refrigerator
or freezer door, the door can open slightly and then
close again.
Be careful not to close the door too hard.
Dew drops
When there is icing or
dew drops formed on the
inner or outer side of the
When warm external air flows into the cool inner surface
of the refrigerator, icing/dew drops can be formed.
Especially, this will happen more easily when you open
and close the refrigerator door more frequently.
Also if the humidity of the installed location is high or
during the rainy season or on a rainy day, condensation can
form on the outer side of the refrigerator. This is a
natural phenomenon that occurs during the humid
weather. Wipe the condensation with a dry cloth.
When the front side of the
refrigerator is warm
Heat pipes are installed around the front part of the
refrigerator and on the divider of the freezer and refrigerator
to prevent condensation from forming. The refrigerator
may feel warmer after the installation or during
summer, this is not a malfunction and is a normal occurance.
P/No. : MFL68083701
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF