Table of contents Introduction Entry Important safety instruction Identification of parts Installation Where to install Door removal Door replacement Feed water pipe installation Height adjustment Operation Starting Adjusting the temperatures and functions (Dispenser / Automatic ice maker) Refreshment center Shelf Wine holder Egg box Humidity control Convert into Deodorizer Suggestion food on storage Care and maintenance a in the vegetable (Applicable Location of foods Storing foods How to dismantle parts General information Cleaning Trouble vegetable compartment shooting or to meat some compartment models only) Introduction Entry The model and serial numbers case or back of refrigerator unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Staple your receipt here. are found on compartment of this unit. These numbers Date of Dealer purchase : purchased from : Dealer address : Dealer phone : Model no. Serial the inner are no. : no. : Important safety instruction Before it is used, this refrigerator must be properly installed and located in accordance with the installation instructions in this document. Never unplug pull it straight your refrigerator by pulling the power cord. on Always grip plug firmly and out from the outlet. When moving your appliance away from the wall, be careful not to roll cord or to damage it in any way. After your refrigerator is in operation, do the power not touch the cold surfaces in the freezer compartment, particularly when your hands these over are damp or wet. Skin could adhere to extremely cold surfaces. Unplug the power cord from the power outlet for cleaning or other requirements. Never touch it with wet hands because you can get an electric shock or be hurt. Never damage, process, severely bend, pull out, or twist the power cord because damage the power cord may cause a fire or electric shock. You have doubts on whether the appliance is properly grounded. Never place glass products in the freezer because when their contents are frozen. they may be broken due to expansion Never allow your hands within the ice storage bin of the automatic ice maker. You could be hurt by the operation of the automatic ice maker. The appliance is supervision. not intended for use by young children Young childeren should be supervised appliance. to ensure that or infirm persons without they do not play with the Never allow anyone to climb, sit, stand or hang on the refreshment center door. These actions may damage the refrigerator and even tip it over, causing severe personal injury. Don't use an extension cord If possible, connect the refrigerator to its own individual electrical outlet to prevent it and appliances or household lights from causing an overload that could cause a power other outage. Accessibility of Supply Plug refrigerator-freezer should be so positioned that the supply plug is accessible for quick disconnection when accident happens. The Supply Cord Replacement If the agent 3 supply cord is damaged, it must be replaced by the manufacturer or its service or a similarly qualified person in order to avoid a hazard. Introduction Child entrapment DANGER: Risk of child entrapment. Before you throw away your old refrigerator or freezer : Take off the doors but leave the shelves in place so that children may not easily climb inside. The appliance is not intended for use by young children or infirm persons without warning supervision. Young children should be supervised Don't store Don't store any other Grounding (Earthing) gasoline appliance. or use In the event of an or to ensure that they do other flammable vapor and not liquids play with the appliance. in the vicinity of this or electric short circuit, grounding (earthing) reduces the risk of electric an escape wire for the electric current. shock by providing In order to prevent possible electric shock, this appliance must be grounded of the grounding plug can result in an electric shock. Consult a qualified electrician or service person if the grounding instructions are not completely understood, or if you have doubts on whether the appliance is properly grounded. improper use Identification of parts Freezer Refrigerator compartment compartment Milk product corner Lamp Door rack Shelf Automatic ice maker Door rack Lamp Wine holder (Optional) Shelf Snack drawer Refreshment center (Optional) Shelf (steel or Egg glass) box Vegetable drawer Door rack Door rack Shelf Drawer (1 or Vegetable drawer/Meat drawer 2) Door rack Lower Humidity switch Conversion switch cover (Meats/Vegetables) NOTE ? 4 If you found some parts missing from your unit, they may be parts only used in other models. (i.c. the "Refreshment center" is not included in all models) Installation Where to locate Select a good location 1. Place your appliance where it is easy to use. 2. Avoid direct placing the unit near heat sunlight or moisture. sources, 3. Air must circulate properly around your appliance operation. If in is a recessed your appliance placed to ensure efficient area in the wall, allow at least (30 cm) a 12 Inches greater clearance above the and 2 inches (5 cm) or more or appliance from the wall. The appliance should be elevated 1 inch (2.5 cm) from the floor, especially if it is carpeted. 4. To avoid vibrations, the appliance 5. Don't install the 5 must be leveled. appliance below 5°C. It may cause affect the performance. Installation Door removal Warning Electric Shock Hazard Disconnect electrical supply to refrigerator before installing. Failure to do so could result in death or serious injury. If your access door is too narrow for the refrigerator to pass through, remove the refrigerator door and pass the refrigerator laterally. Remove lower cover and then feed water tube Lower Remove the lower cover by lifting upward, and then pull up the feed water tube while pressing area shown in the figure to the right. Feed water tube NOTE ? If a tube end is deformed or abraded, cut the part away. Hinge Connection wires cover Remove the freezer 1) Removing the hinge cover by loosening the screws. Separate all connection wires except for the earth line after. compartment Earth line Upper hinge door Keeper 2) Remove the keeper by rotating it counter clockwise ( ) and then lifting the upper Upper hinge up ( ). hinge NOTE ? When removing the upper hinge, be careful that the door does not fall forwards . 3) Remove the freezer compartment door by lifting it upward. This time, the door should be lifted to be enough for the feed completely pulled out. water pipe tube Lower hinge NOTE ? Move the refrigerator compartment door passing through the access damage the feed water pipe tube. door and it down, but be careful not to Remove the 1) Loosen the hinge cover screws and remove Remove connection wire, if any, except for the earth line. the refrigerator door cover. Connection wires 2) Remove keeper by rotating it clockwise ( ) and then remove the upper hinge by lifting Upper hinge itup( ). 3) Remove the refrigerator compartment door by lifting it 6 up. Lower hinge Keeper lay cover Installation Pass the Pass the door refrigerator as refrigerator laterally through right figure. Door access replacement Mount them in the door. Feed water Before installation the shown in the reverse pipe sequence of removal after they pass through the access installation Automatic ice maker operation needs water pressure of 147~834kPa (1.5~8.5 kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.). If water pressure does not reach the rating 147 kPa (1.5 kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed. Keep the total length of the feed water pipe tube within 12 m and be careful for the tube not be bent. If the tube is 12 m or longer it may cause trouble in water feed owing to the drain water pressure. Install the feed water pipe tube at a place free from heat. Connect to potable water supply only. Refer to instructions with water filter kit for installation. Warning 7 Installation Height adjustment If the freezer Level the door by inserting flat ( type) driver into the groove of the left and rotate it clockwise ( ). - compartment door height adjusting screw is lower than the refrigerator compartment door RZMP EFMP INSR If the freezer Level the door compartment door is higher than the refrigerator compartment door adjusting screw - EFMP The the MX MX UHED UED LOK N F LOCK SPERRZ OOM EMP groove of the right height and rotate it clockwise ( ). INSR leveling the door height N N by inserting flat ( type) driver into the RZMP After ER ER N MX N MX UHED UBED LK N FF LOCK SPERRZ ROM TEMP refrigerator doors will close smoothly by heightening the front side by adjusting height adjusting screw. If the doors do not close correctly, performance may be affected. 1. Next Wipe off all dust accumulated during shipping and clean your appliance thoroughly. 2. Install accessories such proper as the ice cube box, cover evaporating tray, etc., in their places. They are packed together to prevent possible damage during shipping. 3. Connect the power supply cord (or appliances on the same outlet. 8 plug) to the outlet. Don't double up with other Operation Starting refrigerator is first installed, allow it to stabilize at normal operating temperatures for 2-3 hours prior to filling it with fresh or frozen foods. When your If operation is interrupted, wait 5 minutes before restarting. Adjusting the temperatures and functions FRZTEMP MN REFTEMP DISPENSER MAX CRUSHD LOCK ON MN WATER MAX C D OFF LOCK SUPERFRZ ROOM TEP FRZ TEMP MIN MAX REF TEMP MIN MAX LOCK ON OFF LOCK SUPER FRZ ROOM DISPENSER WATER CRUSHED Dispenser selection CUBED TEMP button. Super freezer. Temperature adjustment button refrigerator compartment. for Lock button. Temperature adjustment for freezer 9 compartment. button Operation You adjust temperature of and freezer room and refrigerator room. can How to adjust the temperature in Freezer temperature adjustment room BAR Indication Setting temperature the freezer FRZ TEMP compartment How to adjust the temperature in the refrigerator compartment Refrigerator MIN room MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MAX temperature adjustment BAR Indication Setting temperature MIN REF TEMP Whenever MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MAX pressing button, setting is repeated in the order of (Middle) (Weak) (Middle Weak). (Strong) (Middle Strong) The actual inner temperature varies depending on the food status, as the indicated setting temperature is a target temperature, not actual temperature within refrigerator. Refrigeration function is weak in the initial time. Please adjust temperature above after using refrigerator for minimum 2~3days. Dispenser You use selection can select water or ice. Please select water, slice ice and square ice DISPENSER button as you desire. by pressing Please press the push button pushing in cup. lightly by catching and Pressing The border line is indicated for the selected Switch function, "Tak!" sounds if 5 seconds pass after ice comes out. It is sound that the outlet of ice is closed. ? Reference : Please wait for 2-3 seconds in order to take final ice slices or pressing 10 drops of water when switches after taking taking out cup from the ice water. or as Operation automatically make 8 pieces of ice cube at a time, 80 pieces a day. But these quantities may be varied according to various conditions including how many times the refrigerator door opens and closes. The automatic ice maker Automatic ice maker Ice can making stops when the ice storage bin is full. If you don't want to ON use automatic ice-maker, change the ice-maker switch to OFF. - If you want to automatic ice-maker use again, change the switch to OFF-ON. NOTE ? It is normal that noise is a produced when ice made is dropped into the ice storage bin. Ice is When ice maker does not operate lumped together When ice is lumped together, take the ice lumps out of the ice storage bin, break them into small pieces, and then place them into the ice storage bin again. smoothly When the ice maker produces too small water supplied to the ice maker need to If ice is not used frequently, it may or lumped together ice, the amount of adjusted. Contact the service center. lump together. Power failure Ice may drop into the freezer compartment. Take the ice storage bin out and discard all the ice then dry it and place it back. After the machine is powered again, crushed ice will be automatically selected. The unit is newly installed It takes about 12 hours for a newly installed refrigerator to make ice in the freezer compartment. Super Please select this function for prompt freezer. freezer "On" or "Off" is repeated whenever pressing button. SUPER FRZ The arrow mark graphic remains at the On status after flickering 4times when selecting Special Refrigeration "On". Super freezer function automatically turns off if fixed time passes. This button stops button. Lock Locking the LOCK or a Ex) In selecting In selecting "Off" operation of different Release is repeated whenever pressing . Pressing the other button when the button does not operate. selecting 'LOCK', Ex) In selecting "LOCK" 11 Ex) "On" Ex) In selecting again "LOCK" Operation The other functions Ambient temperature display window. Temperature is displayed only by --9°C~49°C. ROOM TEMP Temperature less than -10°C is indicated with 'LO' and temperature more than 50°C is indicated with 'HI'. Temperature may differ from the actual ambient temperature on the upper part of refrigerator (top of door). Door open as it is monitors warning 3 times of warning sounds at the interval of 30 seconds if a minute passes with the door of refrigerator and the hombar door opened or completely closed. Please contact with the local service center if warning continue to sound even after closing the door. Diagnosis (failure detection) function Diagnosis function automatically detects failure when failure is found in product during use of refrigerator. If failure occurs at product, it does not operate though pressing any button and normal indication is not done. In this case, do not turn power off but immediately contact with the local service center. A lot of time are need for service engineer to detect the failed part if turning it off. the Water is cooled while stored in the water tank in the How ice/cold water is supplied then sent to the and dispenser. Ice is made in the automatic ice maker and sent to the or refrigerator compartment, dispenser divided into crushed cubed form ice. NOTE ? It is normal that the water is not very cold at first. If you want colder water, add ice into the How to glass. Select one among crushed ice, water, and cubed ice and slightly press the push switch with a glass or other container. use dispenser Crushed ice Water Light the water indicating lamp by pressing the selection ? 12 button. Water will be dispensed by pressing the push switch with a glass. Cubed ice Light the crushed ice indicating lamp by pressing the selection Light the cubed ice indicating lamp by pressing the button. ? Crushed ice will be dispensed by pressing the push switch with a glass. ? selection button. Cubed ice will be dispensed by pressing the push switch with a glass. Operation Cautions Throw away the ice (about 20 after refrigerator installation. pieces) and water (about 7 glasses) first made The first ice and water may include particles or odor from the feed water pipe or feed water box. This is necessary in case that the refrigerator has not been used for a long time. Keep children away from the dispenser. Children may push switch incorrectly bad or damage lamps. Be careful that food is not block the ice passage. If foods are placed at the entrance of ice passage, ice may not be dispensed. The ice passage may also be covered with ice powder if splinter ice is used only. This time, remove the ice powder accumulated. beverage cans or other foods in ice storage bin for the rapid cooling. Such actions may damage the automatic ice maker. Never store Never use thin Such glasses or crystal glass Never touch Touch may Never crockery to collect ice. containers may be broken. Put ice first into Water may be or purpose of glass before filling water or other beverages. splashed if ice is added to existing liquid in a glass. a a hand remove or other tools part breakage cause a the ice maker Sometimes level the surface Ice is or on ice outlet. hand injury. cover. so that the ice storage bin is fully filled with ice. the ice maker. So, such status may be considered, by the ice piled up just that the ice maker, storage bin is fully filled and ice making operation may stop. near If discolored ice is Never use Ice may be dispensed, immediately contact service center, stopping too narrow or jammed deep glass. in ice passage and, thus, the refrigerator Keep the glass at a proper distance from ice outlet. glass too close to the outlet may hinder ice from coming A 13 may be failed. out. use. Operation Refreshment center How to Open use (Applicable to some models only) the refreshment center door. You can access the refreshment center without opening refrigerator door and thus saving electricity. Inner lamp is lit in refrigerator compartment when the refreshment center door opens. Thus it is easy to identify the contents. Store frequently used foods, such as The refreshment center is kept at a correct temperature thanks to a temperature sensor only for the refreshment center. beverages in the refreshment center. Never Use the refreshment center door as a stand Never take out the inner refreshment use the refreshment center door chopping board and take with sharp tools. care not to Never rest your severely arms or as a damage it press on it. The refreshment center can not function normally without the cover. center cover Never place heavy items on the refreshment center door or allow children to hang it on. Not only can the refreshment center door may be damaged, but also children may be hurt. 14 Operation Shelf Shelf height adjustment refrigerator compartment shelf is movable according to space requirement of foods. The so that you can place it at a height 1 How to separate a shelf : Lift a shelf incling to direction, and then separate it lifting direction. to 2 How to install Position a a shelf shelf to a 1 : desirable height and push into the grooves. Then lower the front side of the shelf and push into grooves. 2 NOTE ? Make sure the shelf is horizontal. If not, it may Wine holder (Applicable to some models only) Wine holder Bottles can adjustment corner. This be stored can laterally with this wine be attached to any shelf. Wine holder adjustment : be separated by pulling it straight out and installed by placing it at the end of the shelf you want and pushing Wine holder it inward. 15 can drop. Operation Egg You box the egg box to wherever can move you want. NOTE ? Never ? Never store the egg box in the freezer compartment use the egg box as an Humidity control ice storage bin. It in the can be broken. or fresh compartment. vegetable compartment The humidity can be controlled by adjusting left/right when storing vegetabes or fruits. the humidity control switch to the High humidity Low humidity Convert into a vegetable or The bottom drawer in the refrigerator can meat compartment be converted into a vegetable or meat compartment The meat compartment maintains the temperature at a lower point than the refrigerator compartment so that meat or fish can be stored fresh longer. NOTE ? Vegetables or fruits are compartment. So, be 16 frozen if the conversion switch is set to meats sure to check it before storing foods. Operation Deodorizer (Applicable to some models only) This system efficiently absorbs strong odors by using the optical catalyst. This system does hot have any affect How to use the on stored food. Since it is installed already installed onto the cool air intake duct from the from refrigerator compartment, you need no separate installation. deodorizing system the Please use closed containers to store food with pungent odors. can be absorbed by other food in the compartment. Otherwise, this oder 17 Suggestion Location of foods (Refer Wine holder to identification of parts) Store wine. Snack drawer Store small foods such Freezer as bread, snacks, Store various frozen foods such ice cream, frozen snacks, etc.. compartment as etc.. meat, fish, shelf Store small packed frozen food. Temperature is likely to increase as door opens. So, do not store long-term food such ice cream, etc.. Freezer compartment door rack Store meat, fish, chicken, etc.. after Freezer wrapping them with thin foil. Store dry. compartment drawer Milk Store milk products such product Egg as butter, cheese, etc.. corner box Place this egg box in the proper location. Store foods of Refreshment frequent use such as beverage, etc.. center Store side dishes distance. Refrigerator compartment or other foods at a proper shelf Refrigerator compartment Store small packed food as milk, juice, beer, or beverages such etc.. door rack Vegetable drawer Store vegetables or fruits. Store vegetable, fruits, meat to thaw, raw etc.. setting the conversion switch as Vegetable fish, drawer /meat drawer conversion corner necessary. Be sure to check the conversion switch setting before storing foods. 18 on food storage Suggestion on food storage Storing foods Store fresh food in the refrigerator compartment. How food is frozen and thawed is important factor in maintaining its freshness and flavor. Do not store food which goes bad easily at low temperatures, such as an bananas, and melons. Allow hot food to cool prior to storing, placing hot food in the refrigerator could spoil higher energy consumption. When storing the food, cover it with vinyl wrap or store in a container with a lid. This prevents moisture from evaporating, and helps food to keep its taste and nutrients. other food, and lead to Do not block air vents with food. Smooth circulation of chilled air temperatures Do not open the door and cause Never so frequently. Opening temperatures keep the door lets too much food in door rack because fully air enter the refrigerator, they Do not store bottles in the freezer compartment compartment Do not refreeze food that has been thawed. This storing frozen food like ice shelf, not in the door rack. Avoid placing moist food may push against by inner racks closed. Freezer Refrigerator compartment warm to rise. that the door cannot be When keeps refrigerator even. in top cream for a they - may break when frozen. causes loss of taste and nutrient. long period, place it refrigerator shelves, on the freezer it could freeze from direct contact with chilled air. Always clean food prior to refrigeration. Vegetables and fruits should be washed and wiped, and packed food should be wiped, to prevent adjacent food from spoiling. When storing eggs in their storage rack or box, ensure that they are fresh, and always store them in an upright position, which keeps them fresh longer. NOTE ? If you keep the refrigerator in a hot and humid place, frequent openning of the door storing a lot of vegetables in it may cause dew to form which has no effect on its performance. Remove the dew with dust cloth free from care. or 19 Care and maintenance How to dismantle parts NOTE ? Dismantling is done in the reverse sequence of assembly. sure to unplug the power plug before dismantling and assembly. Never apply severe force to dismantle parts. Parts may be damaged. Be Freezer Separate the lamp by pulling it out ( ) while slightly striking ( ) and rotating ( ) the lamp compartment lamp cover. Turn the bulb counterclockwise. Max. 40 W bulb for refrigerator is used and can be purchased at a service center. the lamp by pulling it out, and then the lamp. Max. 15 W bulb for refrigerator is used and can be purchased at a service center. Seperate Dispenser lamp remove Freezer remove a shelf, lift the left part of the shelf bit, push it to the direction ( ), lift the right part to the diretion ( ), and take it out. To compartment a shelf Door rack and Lift the door rack holding both sides ( ) and out to ( ) direction. support Ice pull it storage bin Hold the ice storage bin as shown in the right and pull it out ( ) while slightly lifting it figure ( ). It is recommended not to dismantle the ice storage bin unless it is necessary. Be sure to use both hands when removing the ice storage bin, so as not to drop it on the floor. If the ice storage bin does not fit well, rotating device. slightly rotate the After dispenser The water collector has no self-drainage function. So it should be cleaned regularly. Remove the cover by pressing the left side of water collector cover and dry it with a cloth. Press the point marked as shown in the figure to the right to remove the water collector is used cover. 20 Care and maintenance To remove the lamp cover, press the protrusion under the lamp cover to the front and then pull the lamp cover out. Turn the bulb counterclockwise. Max. 40 W bulb for refrigerator is used and can be purchased at a service center. Lamp in refrigerator compartment Refreshment upper rack of the refreshment center and then pull out the refreshment 1 Separate the center center cover ( ). The refreshment center can be removed by pulling it upwards. NOTE Be ? sure to remove parts from the refrigerator door when removing the vegetable compartment, snack drawer and refreshment center cover. 2 Vegetable compartment To remove cover, cover a pull the vegetable compartment vegetable compartment out the bit to the front , lift the front part of the cover as shown by vegetable compartment , and take it 21 out. 1 Care and maintenance General information During average length vacations, you will probably find it best to leave the refrigerator operation. Place freezable items in freezer for longer life. When you plan not to operate, remove all food, disconnect the power cord, clean the interior thoroughly, and leave each door OPEN to prevent odor formation. Vacation time in Most power failures that Power failure are corrected in hour an or two will not affect your refrigerator temperatures. However, you should minimize the number of door openings while the power is off. If you or securely fasten down all loose items inside the refrigerator. damaging the height adjusting screws, turn them all the way into the base. Remove move To avoid The outside wall of the Anti condensation refrigerator cabinet may sometimes get warm, especially just after installation. pipe Don't be alarmed. This is due to the anti-condensation refrigerator to prevent "sweating" on pipe, which pumps hot the outer cabinet wall. Cleaning It is important that your refrigerator be kept clean to food should be wiped up immediately, since it may allowed to settle. Use Exterior a lukewarm solution of mild soap or detergent prevent undesirable odors. Spilled acidify and stain plastic surfaces if to clean the durable finish of your refrigerator. Wipe with a clean damp cloth and then dry. Interior Regular cleaning is recommended. Wash all compartments detergent and warm water. Rinse and dry. a baking soda solution Please plug is or a mild After cleaning power Warning verify that the power cord is not damaged, plug is well inserted into the power consent. Always remove electrical parts power cord from the wall outlet power prior to not cleaning overheated, in the or vicinity of (lamps, switches, controls, etc.). Wipe up excess moisture with a sponge or cloth to prevent water or liquid from getting into any electrical part and causing an electric shock. Never use metallic scouring pads, brushes, coarse abrasive cleaners, strong alkaline solutions, flammable or toxic cleaning liquids on any surface. Do not touch frozen surfaces with wet or damp hands, because damp object will stick or adhere to extremely cold surfaces. 22 Care and maintenance Trouble shooting Before calling for service, review this list. It may save you both time and expense. common occurrences that are not the result of defective This list includes workmanship Occurrence or materials in this Possible appliance. Solution cause Runing of refrigerator Refrigerator compressor does not run. Refrigerator control is off. Set refrigerator control. See setting the controls. Refrigerator is in defrost This is normal for cycle. at wall outlet is disconnected. Plug Power outage. Check house Refrigerator Refrigerator runs one too much or too long a fully automatic defrosting refrigerator. The defrost cycle occurs periodically. is lights. larger than the previous you owned. Room or Refrigerator has recently been disconnected for a period of time. Large Doors amounts of warm or hot food are opened too recently. frequently or too long. Refrigerator or freezer door slightly open. plug is tightly pushed into Call local electric company. This is normal. Larger, more efficient units run longer in these conditions. It is normal for the refrigerator to work longer under these conditions. outside weather is hot. may have been stored Make sure outlet. may be It takes some to cool down hours for the refrigerator completely. Warm food will cause the refrigerator to run longer until the desired temperature is reached. Warm air entering the refrigerator causes it to run longer. Open the door less often. Make sure the refrigerator is level. Keep food and containers from blocking door. See problem section. OPENING/CLOSING of doors. Refrigerator control is set too cold. Set the refrigerator control to a setting until the refrigerator temperature is satisfactory. warmer Refrigerator worn, or cracked, freezer gasket is dirty, or poorly fitted. Clean or change gasket. Leaks in the door seal will cause refrigerator to run longer in order to maintain desired temperatures. Thermostat is at a constant 23 keeping the refrigerator temperature. This is normal. Refrigerator goes on and off to keep the temperature constant. Care and maintenance Occurrence Possible Refrigerator Thermostat is at a constant compressor does not run. Temperatures Solution cause keeping the refrigerator temperature. This is normal. The refrigerator goes on and off to keep the temperature constant. are too cold Temperature in the freezer is too cold but the refrigerator temperature is Set the freezer control to a warmer setting until the freezer temperature is Freezer control is set too cold satisfactory. satisfactory. in the is too cold and the freezer Temperature refrigerator Refrigerator Set the control is set too cold. warmer refrigerator setting control to a temperature is satisfactory. Food stored in drawers freezes. Refrigerator Meat stored in fresh meat drawer freezes. See above solution. control is set too cold. Meat should be stored at a temperature just below the freezing point of water ( 32˚F, It is normal for ice crystals to form due to the moisture content of meat. 0 ˚C) for maximum fresh storage time. Temperatures are too warm Temperatures in the refrigerator or freezer Freezer control is set too Set the freezer or refrigerator control to a colder setting until the freezer or refrigerator temperature is satisfactory. warm. are too warm. Refrigerator Refrigerator control is set too warm. control has some effect on freezer temperature. Doors are opened too frequently or too long. Door is Large slightly Warm air enters the refrigerator/ freezer whenever the door is opened. Open the door less often. Close the door completely. open. amounts of warm or hot food may have been stored Set the freezer or refrigerator control to a colder setting until the freezer or refrigerator temperature is satisfactory. recently. Wait until the refrigerator or freezer has a chance to reach its selected temperature. Refrigerator has recently been disconnected for a period of time. Temperature in the refrigerator Refrigerator control is set too warm. A refrigerator requires completely. Set the setting. is too warm but the freezer temperature is satisfactory. 24 some hours to cool down refrigerator control to a colder Care and maintenance Possible Occurrence Solution cause Sound and noise Louder sound levels when refrigerator is on. Today's refrigerators have increased storage capacity and maintain more Louder sound levels when Refrigerator operates at higher pressures during the start of the ON cycle. even It is normal for sound levels to be higher. temperatures. This is normal. The sound will level off the refrigerator continues to run. as compressor comes on. Vibrating or rattling noise. Floor is uneven or Refrigerator rocks moved slightly. weak. on the floor when it is placed on the top of the refrigerator vibrating. Items are Dishes are vibrating the refrigerator. Refrigerator is on the shelves in touching wall or cabinets. Be sure floor is level and solid and can adequately support refrigerator. Remove items. It is normal for dishes to vibrate slightly. Move dishes slightly. Make sure refrigerator is level and firmly set on floor. Move refrigerator so that it does not touch the wall or refrigerator. Water/Moisture /Ice inside refrigerator Moisture collects the inside walls of the refrigerator. on The weather is hot and humid which increases the rate of frost buildup and internal sweating. This is normal. Door is slightly open. See problem section opening/closing of doors. Door is opened too often or too long. Open the door less often. Water/Moisture /Ice outside refrigerator Moisture forms the outside of the refrigerator between doors. Weather is humid. This is normal in humid weather. When humidity is lower, the moisture should disappear. Door is slightly open,causing cold air from the inside the refrigerator to meet warm air from the outside. This time, close the door Moisture may be formed in It will go better to wipe moisture and then opening doors once again. on or Moisture forms the dispenser or refreshment high temperature and high humidity since on heater turns off if not doors for a long time. center 25 opening the completely. Care and maintenance Occurrence Odors in Possible Solution cause refrigerator Clean interior with sponge,warm water and baking soda. Interior needs to be cleaned. Food with strong odor is in the refrigerator. Cover food completely. Some containers and wrapping materials produce odors. different container wrapping materials. Move packages that keep door from closing. Use a or brand of Opening/Closing of doors/Drawers Door(s) will not close. Food Door(s) will not close. Door was closed too hard, door to open slightly. package is keeping door open. causing other Refrigerator is not level. It rocks floor when it is moved slightly. Floor is uneven or Refrigerator rocks is moved slightly. on the weak. on the floor when it Close both doors gently. Adjust the height adjusting Be sure floor is level and support refrigerator. Contact carpenter to screw. can adequately correct sagging or sloping floor. Refrigerator Drawers are difficult to move. Food is drawer is touching wall touching shelf on Track that drawer slides or cabinets. top of the on is dirty. Move refrigerator.. Keep less food in drawer. Clean drawer and track. Dispenser Dispenser will not dispense ice When the first into the bin, the Ice storage bin is empty. Freezer temperature is set too warm. Household water line valve is not open. supply of ice is dropped dispenser should operate. Turn the freezer control to a higher setting so that ice cubes will be made. When the first supply of ice is made, the dispenser should operate. Open household water line valve and allow sufficient time for ice to be made. When ice is made, dispenser should operate. Refrigerator 26 or freezer door is not closed. Be sure both doors are closed. Care and maintenance Occurrence Possible Solution cause Ice has melted and frozen around auger due to infrequent use, temperature fluctuations and/or power outrages. Dispenser will not dispense ice. Remove ice storage bin, and thaw and the contents. Clean bin, wipe dry and replace in proper position. When new ice is made, dispenser should operate. Ice dispenser is jammed. Ice cubes are jammed between the ice maker arm and back of the bin. Ice cubes are frozen together. Remove the ice cubes that the dispenser. Use the dispenser often together. so are jamming that cubes do not freeze Dispenser will not dispense water. Ice cubes that have been purchased or made in some other way have been used in the dispenser. Only the ice cubes made by the ice maker should be used with the dispenser. Household water line valve is not open. See problem "Ice maker is not making any ice." Open Refrigerator Water has an odd taste and/or odor. or freezer door is not closed. Water has been in the tank for too long. Be household water line valve. sure both doors are closed. glasses of water supply. Draw and discard glasses to completely rinse Draw and discard 7 to freshen the an additional 7 out tank. Unit not properly connected to cold water line. Sound of ice This sound is normally made when bin. Volume may vary according to dropping Sound of water Connect unit to cold water line which water to kitchen faucet. supplies automatically made ice is dropped into ice storage refrigerator's location. This sound is normally made when ice maker is the automatically made ice. supply Other Please 27 supplied with thoroughly read 'Automatic ice maker and dispenser' water after dropping in this manual.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project