LG WD-1412RD Owner's Manual
Add to my manuals31 Pages
LG WD-14120RD is a fully automatic washing machine with a jumbo drum that can wash about 40% more load than conventional machines. It features Intelligent Wash System that detects load and water temperature to minimize energy and water consumption. Direct Drive System rotates the drum without belt and pulley, reducing noise and vibration. Child-Lock prevents children from changing the program during operation. Auto Restart restarts the washing cycle from where it stopped in case of power failure.
advertisement
▼
Scroll to page 2
of 31
Washing Machine OWNER'S MANUAL WD-1012RD WD-1212RD WD-1412RD Thank you for buying a LG Fully Automatic Washing machine. Please read your owner's manual carefully, it provides on safe installation, use and maintenance. instructions Retain it for future reference. Record the model and serial numbers of your washing machine. P roduct Feature Jumbo drum 40% LG's jumbo drum conventional can wash about 40% machines. A washing more bigger load than drum improves the wash performance. More economical Intelligent Wash by Intelligent System Wash System detects the amount of load and water temperature, and then determines the optimum time to minimize energy and water washing Direct Drive water level and consumption. System The advanced Brushless DC motor rotates the Drum without belt and directly pulley. Child-Lock The Child-Lock pressing system has been used any button to Low noise speed change control to prevent children from the program during operation. system the amount of load and balance, it load to minimize the spinning noise level. By sensing evenly distributes Auto Restart If the washing machine is turned off by a power failure, it will restart automatically from the position it stopped at adjusting accordingly. C ontents Warnings....................................................................................3 Specification ..............................................................................5 Installation..................................................................................6 Care before washing................................................................12 Adding detergent .....................................................................13 Function ...................................................................................14 How to use washer ..................................................................15 Maintenance ............................................................................24 Troubleshooting guide Terms of 2 .............................................................27 Warranty ...................................................................30 arnings W READ ALL INSTRUCTIONS BEFORE USE For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. WARNING! ! IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, the ? Do not install be ? ? or store the washer where it will ? exposed to the weather. Do not tamper with controls. repair or replace any part of the washer attempt any servicing unless specifically instructions or published user-repair instructions ? that you understand and have the skills to carry Keep the area underneath and around your appliances free of combustible materials such lint, paper, rags, chemicals, etc. Close supervision is necessary if this is used by young children. Do not allow children to play on, with, this ? persons when using or dry articles that have been in, washed in, soaked in, or spotted with explosive substances (such as wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may ignite or explode. To avoid such a result, carefully follow the garment manufacturer's wash and care or instructions. out. ? Do not wash combustible recommended in the user-maintenance ? injury to cleaned Do not or or washer, follow basic precautions, including the following: disable ? appliance ? or inside or Never reach into washer while it is ? The until the drum has hang on ? moving. completely stopped. laundry process retardant of fabrics. can to this possibility of electric shock, appliance from the power supply or distribution crawl inside the washer. ? try disconnect the washer at the household or the door or To minimize the unplug or any other appliance. Do not leave the washer door open. An open door could entice children to Do not slam the washer door closed force the door open when locked. This could result in damage to the washer. as Wait reduce the flame ? panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning. Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. dryer is intend only for drying textile material in water. SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This grounded. In the event of malfunction or breakdown, grounding will reduce the risk by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance. Do not use an adapter or otherwise defeat the grounding plug. appliance must be of electric shock ? ? If you don't have the proper WARNING : outlet, consult an electrician. Improper connection of the equipment-grounding conductor can result in risk of electric qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a proper outlet installed by a qualified electrician. shock. Check with a - 3 W arnings To minimize the risk of fire in ? Items that have been a tumble dryer, the following spotted or soaked with vegetable placed in a tumble dryer. or should be observed: cooking oil constitute a fire hazard and should not be Oil-affected items sources Such as ignite spontaneously, especially when exposed to heat dryer. The items become warm, causing an oxidation can in a tumble reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can enought to catch fire. Piling, stacking or storing oil-affected items can become hot prevent heat from escaping and so create a fire hazard. If it is unavoidable that fabrics that contain vegetable or cooking oil or have been products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard. washed in hot water with extra etergent-this will reduce, but not eliminate, the hazard. The 'cool down' cycle of tumble dryers should be used to reduce the temperature of the items. They should not be removed from the tumble dryer or piled or stacked while hot. contaminated ? ? by hair care Items that have been previously cleaned in, washed in, soaked in or spotted with petro/gasoline, dry-cleaning solvents or other flammable or explosive substances should not be placed in a tumble dryer. Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and was removers. Items containing foam rubber foam) or similarly testured dryer on a heat setting. heated, produce fire by spontaneous combustion. (also known as rubber. like materials should not be dried in Foam rubber materials can, when ? Fabric softeners a latex tumble products should not be used in a tumble dryer to eliminate electricity unless this practice is specifically recommended by the the fabric softener or product. or similar the effects of static manufacturer of ? Undergarments dryer. that contain metal reinforcements should not be placed Damage to the tumble dryer can result if metal reinforcements come drying. When available a drying rack could be used for such items. ? Plaxtic articles such be ? placed in a as tumble shower caps or babies waterproof napkin loose covers a tumble during should not dryer. Rubber-backed articles, clothes fitted with foam urbber pads, placed in a tumble rubber-coated tennis shoes should not be 4 in pillows, galoshes dryer. and S pecification Power plug If the it supply cord is damaged, must be replaced by the manufacturer or its service agents similarly qualified person in Drawer or a (For detergent and fabric softener) order to avoid Control a hazard. panel Drain hose Door Lower cover Drum Adjustable Drain pump filter Lower Drain feet cover cap plug Name Power supply : Front : 240V~,50Hz Size : Weight Wash capacity Dry Capacity : loading washing machine 600mm(W) 600mm(D) 850mm(H) 71kg : 7kg : 4kg Max. Watt : 2100W (Wash) 2150(Dry) : No spin/400/800/1000/1400[WD-1412RD] Spin speed No spin/400/800/1000/1200[WD-1212RD] No spin/400/600/800/1000[WD-1012RD] Water consumption :75 (10.7 /kg) Permissible water pressure : 0.3-10kgf/ (30-1000kPa) The external hot water supply 60˚C and must NOT be above 70˚C Permissible cold water TT temperature : 4-25˚C co.y with the requirement by certification Type Test Mark. No further backflow protection required for connection to the water supply. : Appliance The appearance and specifications may be varied without notice to raise the units quality. Accessories Inlet hose(1EA) Option : Hot/Cold(2EA) Spanner 5 nstallation I or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. Install Transit bolts The appliance is fitted with transit bolts to Removing prevent internal damage during transport. transit bolts 1. To prevent internal damage during transport, the special 3 bolts are locked. Before operating the washer, remove the bolts ? If they along with the rubber vibration, along with the rubber bungs by slightly twisting the bung. Keep the 3 bolts and the spanner for future use. bungs. not removed, it may cause noise and malfunction. are 3. Take out the 3 bolts heavy ? Whenever the appliance is transported, the transit bolts must be refitted. cap 2. Unscrew the 3 bolts with the spanner 6 supplied. 4. Close the holes with the caps supplied. nstallation I Installation place requirement Level floor Drain Hose Allowable Washer : under entire washer is 1˚ slope Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with than Laundry one Additional Clearance : For wall, door and floor modeling is (10cm : rear /2cm:right & left side) Tub approx. 2cm Do not more appliance. place or store required. laundry products washer at any times. They can damage the finish or on top of controls. 650 850 600 BS Plug Safety Details (For U.K. User) IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN AND YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE This Green and appliance Yellow(Earth) must be earthed E Brown(Live) L Blue(Neutral) N Cord grip As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the identifying letter E or by the earth symbol ( ) or coloured Green or Green and Yellow. The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or The wire which is coloured Brown must be connected to the terminal which is marked with the letter L If a 13 amp (BS 1363) plug is used, fit a coloured Black. or coloured Red. 13 amp BS 1362 fuse. 7 nstallation I Electrical connection 1. Do not use an extension cord or double adapter. supply cord is damaged, it must be replaced by the similarly qualified person in order to avoid a hazard. Always unplug the machine and turn off the water supply 2. If the 3. 4. Connect the machine to 5. The appliance Washing must be an manufacturer after so that the plug is easily its service agents or use. earthed socket in accordance with current positioned or wiring regulations. accessible. Machine is to be connected to the water mains using hose- new sets and that old hose-sets should not be used. Connecting water hose supply strip or crossthread when connecting Inlet hose to the valve. Don't If the supply pressure is more than decompression device should water 1000kPa, a be installed. ? Two rubber seals are supplied water inlet hoses these prevent ? are with the in order to water leaks. Check water tightness of washing by turning the tap machine connections Hose connector completely Rubber seal Hot water ? Cold Make sure that there is no kink on the hose and that it is not crushed. water Hot(option) of the necessary. tap ? Cold on. Periodically check the condition hose and replace the hose if tap When your washer has two valves, ? The Inlet hose which has red connector is for the hot water ? ! ? tap. If the washer has two valves, the energy is saved by using hot valve. Caution This condensation-type tumble dryer is intendede to be connected to the water mainsthe maximum(10kgf/cm2, 1000kpa) and mainimum(0.5kgf/cm2, 30kpa) persissible inlet water pressure. ? If this appliance is supplied device, the cord extension that it is not ? ? from cord extension set or an electrical portable outlet portable outlet device must be positioned or ingress of moisture. a set or electrical subject to splashing Do not install the washer where it is Plug the power cord of this washer switched 8 earthed. 8 so directly exposed to sunlight, wind, rain etc. into a properly installed standard power point that is nstallation I Tap without Normal 1. Unscrew the fixing attach the tap. screw thread & 2. to screw type inlet hose Push the connector up till the rubber packing with the 3. is in tap. Then tight contact tighten the 4 screws. Tap without Normal 1. Untighten the upper thread & connector 2. touch one packing contact with the Upper Rubber Connector Fixing the 4 tighten packing screw type inlet hose Push the upper connector up till the rubber screw. Middle Rubber connector Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. is in 3. Connect the water to the middle tight tap. Then pushing the supply hose connector, plate down. screws. Upper Connector packing Plate Upper ? In case large the diameter of the remove Guide the tap is Connector Water hose Middle guide plate. connector plate ? Turn the middle connector not to have water leaked. Connector ? Make sure that the rubber seal is inside the hose connector. ? To supply separate the water supply hose from the middle connector shut off the inlet hose plate tap. Then pull the down, pushing the down. Hose connector Rubber seal Used the horizontal Horizontal tap tap ? Your machine comes with only cold water connection. ? Extension tap Make sure that there are no kinks in the hose and that it is not crushed. Square tap 9 I nstallation Installation of drain hose ca. ca. 145 100 cm cm ? max.10cm min.60cm ca. 105 When secure cm ? installing the drain hose sink, it tightly with a string. Proper securing protect water 100 damage due to leakage. Laundry ca. of the drain hose will the floor from tub cm Hose ca. 145 Retainer cm Tie 100cm min. 60cm max. ca. ? 100 Proper securing cm min.60cm max.10cm cm The drain hose should not be higher than ? 105 placed above the floor. of the drain hose will protect the floor from damage due water ? to leakage. When the drain hose is too long, do not force back into the washer. This will cause 10 abnormal noise. strap max. 100cm min. 60cm I nstallation Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the floor the appliance on a solid and level surface, preferably in of a corner room. 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces Make sure of wood etc. under the that all four feet are feet) stable and resting on the floor and then check appliance is perfectly level. (use spirit level) that the a Adjustable Higher Adjustable feet Lower feet Diagonal Check When pushing down the edges of the washing machine top plate diagonally, machine should not all. (Please, move check both the up and down at of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the feets again. 11 C before are Caring before washing washing 1. Care Labels Look for garment 2. label on your clothes. This will tell you about the fabric content of your and how it should be washed. a care Sorting To get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always transfer sort dark colors from soiled items with Soil 3. pale colors and whites. Wash discoloration of white etc. If causing lightly soiled can occur one. (Heavy, Normal, Light) (White, Lights, Darks) (Lint producers, Collectors) Color Separate Separate Lint Wash lint Caring before separately as dye and lint possible, do not wash heavily clothes according to amount of soil. white fabrics from colored fabrics. and lint collectors producers separately. loading Combine large and small items in a load. Load large items first. Large items should not be more than half the total wash load. Do not wash single items. This may cause an out-of-balance load. Add one or two similar items. ? Check all that pockets to make sure empty. Items such nails, hair clip, matches, pens, they are coins and keys can damage as both your washer and your clothes. ? Close zippers, make sure snag ? on hooks and other clothes. Pre treat dirt and stains a little strings to that these items don't detergent by brushing dissolved in water onto stains like collars and cuffs to help 12 shift dirt. dding detergent A Adding detergent 1. The Dispenser and fabric softener 3. Detergent dosage Drawer ? The detergent should be used according to of the detergent manufacture. the instruction max ? If too much detergent is used more than the recommended amount, too many suds can occur and this will decrease the washing result heavy malfunction) or cause ? Use powder loading ? ? Main wash Pre Wash only + ? (Causing a detergent only for the front washer. Detergent for water Main Wash load to the motor. usage may need to be temperature, water adjusted hardness, size and soil level of the load. For best 2. results, avoid oversudsing. Adding Fabric Softener ( ) MAX MAX 125 ml 125ml Tips Full load Part load ? Do not exceed the maximum fill line. Overfilling can cause clothes. 3/4 of the normal amount. : 1/2 of full load. ? Detergent is flushed from the dispenser beginning of the cycle. at Do not leave the fabric softener in the Softener will during ? : Minimum load the detergent drawer for more than (Fabric softener could harden) ? to early dispensing of the fabric softener which could stain ? according : manufacturer's recommendation. 2 days. be added automatically cycle. the last rinse Do not open the drawer when water is supplied. ? Solvents(benzene, etc) are not allowable. NOTE Do not pour fabric softener on the cloths directly 13 unction F Recommended label data based Energy ¡ ( ) : courses according on to the laundry type program cotton 60˚C, tested in accordance with EN60456. WD-1012RD/1212RD Fabric Program Cotton Proper Temp. (Option) Type Color fast garments Water Washing Load Liter (Option) 60˚C (Cold, (shirts, night dresses, Main+(Pre) pajamas...)and lightly soiled 30˚C, 40˚C, 95˚C) white cotton (underwear...) Cotton-Eco Laundry type is the same 60˚C in Cotton. (40˚C) (Cold, Main+(Pre) 30˚C,60˚C) Delicate Wool Hand Wash laundry easily 30˚C damaged.(silk, curtains...) (Cold, 40˚C) Main Machine washable woolens with pure new wool only. Main "Hand Wash" marked delicate and wool laundry. Laundry type Quick 30 in Cotton and Pre Wash : If the is the 30˚C (Cold, 40˚C) Cold (30˚C,40˚C) same Synthetic. laundry 75 5.0kg 73 7.0kg 75 5.0kg 68 3.5kg 70 3.0kg 60 1.0kg 48 2.0kg 52 1.0kg 48 2.0kg 52 1.0kg 48 5.0kg 48 2.0kg 40 40˚C Synthetic Polyamide, Acrylic, Polyester. Delicate 7.0kg Main+(Pre) is 30˚C (Cold, 40˚C) heavily soiled, Time (Option) Minutes in 120(min.) (60,30/90/150) 163(159) 163(159) 120(min.) (60,30/90/150) 178 120(min.) (60,30/90/150) 92 - 67 Main - - 61 - - 60 Main "Pre Wash" Dry in course - - 30 - is recommended. Pre Wash is available in Cotton-Eco, Cotton, Synthetic program. Water Temperature : Select the water temperature to the wash cycles. Always follow garment manufacture's Program 14 care label or instructions when Cotton 40°...is proper for normal Soiled clothes. laundering. H ow to use washer ime Delay ime Save D ime Pre Quick- Rinse Hold 1400 95 1000 60 800 40 400 30 Super Main r Lk Left Normal N Spin old 15 N rmal(12 Small( (min Power Star 1. Cotton Pause 3. Auto half load. automatically selected upon power on. ? ? Press the ) button ? Press the Start/Pause button. ? Initial condition Power( to start. Auto half load saves you time and when money washing smaller loads. The washing machine is fitted with a self adjusting water level system. - Wash : Main wash This system enables the machine to use the amount of water needed to wash - Rinse : 3 times and rinse the - ? particular Spin : 1400 rpm [WD-1412RD] laundry in relation to the load. 1200 rpm [WD-1212RD] 1000 rpm [WD-1012RD] - - Water temperature ? 60˚C Program : Cotton 2. Manual ? : Press the Selecting Power( ) button to start. Select the conditions which you want to use, by pressing each button. For selecting the each conditions, please refer to the page15~page22 ? Press the Start/Pause button. 15 ow to use H washer Deli ate im Syntheti D la im a ool D im L Hand ash Cotton H 1 ld Qui k- 91 6 8 Cotton-E rLk ft 14 Rnse Pr 4 Super N rmal1 4 3 N Main Cld rmal Small ) min Star (1) (2) (3) (4) Button Dial : Pause Button : ) Power Program Start/Pause (5) (6) (7) (8) Program : ) 3 o Wash Child Lock Button : Rinse Button : Spin Button : Time Button : Water (9) Button : Time Save (10) Button : Dry (11) Door Lock (12) Button : Power Delay Temp. Start/Pause Program ? 7 programs are available according laundry type. - Cotton-Eco - Cotton - - 1. Start - ? This Start/Pause button is used to start - - wash cycle or pause the wash cycle. ? If temporary stop of wash cycle is needed, press "Start/Pause" button. ? When in ? Synthetic Cotton-E ool Hand ash Qui o k- 3 Quick 30 Lamp will light up to indicate selected at the end of the wash Program When Start/Pause button is Cotton/Eco program is selected. after 4 minutes. NB. The door will not open before 1 to 2 minutes when Pause is selected, or Syntheti Cotton Delicate Wool Hand Wash 1. Pause, the power is turned off automatically ? to the ate program. 2. Pause ? Deli - By turning the pressed, automatically Program dial, the program is selected in order of "Cotton-Eco cycle. Cotton Synthetic Hand Wash Delicate Wool Quick 30". Regarding to the laundry type for each program Please refer to the page13. 2. Course - Cotton-Eco - - Cotton - - - 16 Synthetic Delicate - Wool Hand Wash Quick 30 ow to use H washer Wash ? Child lock By pressing the Wash button, the wash type can - be selected. ash If you choose to lock the buttons on the control assembly to prevent tampering, this Main -Pre+Main function may be selected. 1. Child lock 1. Main ? ? Main course is available for lightly or ? If the is heavily soiled, "Pre + The be set by pressing and and Rinse button Main" ? Synthetic program. required lamp identification. will light up for ? ime Rinse as is effective. Pre Wash is available in Cotton-Eco, Cotton and can Main laundry course ? + Child lock holding the Wash simultaneously. normally soiled laundry. 2. Pre Rinse When child lock is set, all buttons To deactivate Child lock are Left inoperable. system, press and hold the Wash and Rinse button simultaneously again. Rinse as ? To change ime Left to the desired program, whilst in child lock mode. 1. Press and hold both Wash and Rinse button together once again. 2. Press the Start/Pause button. 3. Select the desired program and press the Start/Pause button again. Change the desired program as ? Star Rinse The child lock is Star Pa be set at any time and it canceled when operational can automatically errors occur. Pa Also Child lock works when power is off. 17 H washer ow to use Rinse Rinse Hold Spin By pressing ? button, Normal be selected. - - - - the Rinse the Rinse Super type can No No Spin + Rinse Hold Super + Rinse Hold [WD-1012RD] ? Cotton-Eco / Cotton / Synthetic performs 3 Rinses /Quick 30 performs 2 Rinses ? Use the + 1 more rinse time. - - 400 - 400 - 600 - 800 - 800 - 800 - 1000 - 1000 - 1000 - 1200 - 1400 ? excess - Is selected by pressing the Rinse button this function leaves clothes in the repeatedly washer; suspended in the without entering into spin. water after a rinse - If you want to drain and spin, when Rinse Hold function is proceed, Press the - Press the ? only, select the No program. required lamp identification. 18 Spin light up for 800 1000 400 800 1000 400 800 1000 No Spin 400 800 No Spin 800 1000 No Spin Quick 30 [WD-1412RD] 800 1000 1400 No Spin 1200 No Spin [WD-1212RD] 400 will 400 Wool / Hand Wash 400 If you want to drain The - according follows. Delicate 400 function and select program. is available Synthetic 400 Start/Pause button to cancel the Rinse Hold spin speed or program. Start/Pause button again to start as Cotton-Eco / Cotton 800 - ? Spin speed [WD-1412RD] 1400 No Spin [WD-1212RD] 1200 No Spin [WD-1012RD] 1000 No Spin 3. Rinse Hold ? Spin selection program dirt - 400 rinse when additional Super rinsing is desired to remove and detergent soiled loads. spin speed - 1. Normal [WD-1412RD] the [WD-1012RD] [WD-1212RD] [WD-1412RD] No Spin No Spin No Spin Super ? Spin button, be chosen. - Delicate / Wool / Hand Wash 2. [WD-1212RD] the By pressing can ? Spin Super Normal 1. Normal ? No Spin Normal 800 1000 [WD-1012RD] 400 800 1000 No Spin to the ow to use H 2. No ? Spin Time If "No after It is washer Spin" is selected, draining water. possible to rinse when "No remove Spin" the washer this spin is selected stops on the on the Wool, Delicate and Hand Wash program. The required lamp identification. ime 1. Time will light up for Delay Delay ime Delay Delay Preparing washing before starting "Time Delay" - - - Turn on the water tap. Load laundry and close the door. Place the detergent and fabric softener in the drawer. ? How to set "Time - - - Delay" Power( ) button. Turn the Program dial to select the program you require. Press Time Delay button and set the Press desired time. - ? Press the Start/Pause button.(":" blinks.) If Time Delay button is pressed, "3:00" is displayed. The maximum delayed time is 19:00 hours and the minimum time is 3:00 hours. ? ? Each pressing of the delay by one hour. To cancel the time Power( ? Time or ? delay, press the button. ) 'expected time' from the completion of washing cycle process (Wash, Rinse, Spin). Delay present button advances time is to the selected According to the condition of water supply and temperature, the delayed time and the actual washing time may vary. 19 H ow to use Water ? washer Time Save Temp. By pressing the Temp. ime Save button, the water temperature can be selected. - Cold -30˚C/40˚C/60˚C/95˚C 1. Time Save ? emp. 1. Water ? - - - Water temperature below according - can Cotton 60˚C 95˚C be selected ? Cold Cold 30˚C 40˚C 30˚C 40˚C The required temperature lamp identification. For the more to the page13. 20 To detailed will light up for information, please refer can this use be used to reduce the time press the Time Save before the wash program is option once This option program. Delicate & Wool & Quick 30 30˚C 40˚C Cold Hand Wash Cold 30˚C wash program. a started. as to the program. Synthetic 60˚C option of button Cotton-Eco 60˚C 40˚C 40˚C - ? Temperature This is not available with Quick 30 washer ow to use H 2. Dry ? 30 90 150 This washer-dryer's ? automatical process from washing to drying can be Normal Small ? selected easily. For most even make drying, all articles in sure the clothes load are similar in material and thickness. ? Do not overload dryer by stuffing too dryer can handle a load of up to 4kg dry weight of articles. When loading, shake out each handful of clothes so that they can tumble freely. Items should not be loaded in condition, as this will lengthen a tangled drying the time. Woolen Articles dry woolen articles. Pull them original shape, they ary them flat. Woven and Loopknit Materials Some woven and loopknit materials may shrink, by varying amounts, depending on their quality. Always stretch them out immediately after drying. - ? Drying guide Your Do not tumble to their many articles into drum. Items must be able to tumble freely. - ? If you open door and dryer has finished its remove load before cycle, remember to press the Start/Pause button. ? After the end of pressing dry, " " is displayed. By the "Start/Pause" button the program can be ended. If you not press the "Start/Pause" button, the program is ended after about 4 hours. " " - Permanent Press and - - Cooling Cycle. Do not overload your Take out permanent press articles as as the dryer stops to reduce wrinkles. Fibre 1. Drying Time Guide - (Manual operation) ? By pressing can ? ? ? ? ? the Dry button, the drying time be selected. Drying course can last up to 150min. When selecting drying only, drying course will start after 15min spining. These drying times are given as a guide to help you set your dryer for manual drying. Drying times can vary greatly depending on dampness, room temperature and type of fabric and your own experience will be your best guide. 120 minutes (Normal): Cotton 4kg. 60 minutes (Minimum): Cotton 2kg. 30/90/150 (minutes) 30min.: Cotton 1.5kg, 90min.: Cotton 3kg 150min.: Towel 4kg Synthetics dryer. or soon Leather Materials check the manufacture's instructions. Always Baby Clothes an Night Gowns Always check the manufacture's - instructions. Rubber and Plastics dry any items made from or containing rubber or plastics, such as: a) aprons, bibs, chair covers b) curtains and tablecloths Fiberglass Do not dry fiberglass articles in your dryer. Glass particles left in the dryer could be picked up by your clothes the next time you use the dryer and irritate your skin. - Do not - - - 21 ow to use H 3. ? ? When drying cycle is completed, [COOL DOWN] is displayed on the Multi display. The COOL DOWN is when a setting drying cycle Power is 1. Power When you are not remove a load of clothes from the dryer as soon as it stops, wrinkles ? Power Completion of Drying automatically complete. ? washer can ? form. ? The COOL DOWN operating periodically tumbles, rearranges and fluffs the load to avoid wrinkles without heat for up to 4 hours. ? The message will continue to display until the clothes are removed or the START/PAUSE button is Press the Power( on and off. power pressed. ? Door Lock button to turn To cancel the Time Delay function, the Power( ) button should be pressed. 2. Initial ? ) Program When the Power( ) button is pressed, the washer is ready for Cotton program. And the other initial conditions as follows. So, if you want to advance into the washing cycle without changing the program, just press Start/Pause button and then the washer will proceed. Initial program [WD-1412RD] ? It shows whether the door or ? can be open ? not. When the be open. lamp is on, the door can not Cotton Program / Main wash / Normal Rinse / 1400 rpm / 60˚C [WD-1212RD] ? Cotton Program / Main wash / Normal Rinse / 1200 rpm / 60˚C [WD-1012RD] ? 22 Cotton Program / Main wash / Normal Rinse / 1000 rpm / 60˚C H washer ow to use 3. Display ? Completion of washing When washing cycle is completed, is displayed on the "Multi display". " " 1. ? Special function display When Child lock is selected, the is displayed. " " ? After the end of ? When time dry, " " is 4. Time left ? displayed. delay is selected, it shows the remaining times to finish the selected During washing cycle, the remaining washing time is displayed. Recommended program ? ( ) ¡ - program. - 2. Self ? diagnose display If the washer encounters operation, displayed. " " : " " " " " " a fault - during - the associated fault will be - - Water pressure sensing : Problem of : Door is not closed : Over load in motor overfilling error - " " " " " " " " " : Over load in motor : Water inlet trouble : Drainage : : " trouble Unbalanced load Water temperature trouble " : Dry heater or manufacturer. WD-1012RD/1212RD Cotton-Eco : around 2 hours and 58 minutes Cotton : around 2 hours and Synthetic 43(39) minutes around 1 hours and 32 minutes : Delicate : around 1 hour and 7 minutes Wool : around 1 hour and 1 minutes Hand Wash : around 1 hour Quick 30 : around 30 minute water ? " : by thermostat The washing time may vary by the laundry, water pressure, water temperature and other washing conditions. amount of ? If an unbalanced load is detected or if the suds removing program operates, the wash time may be extended. (Max. increasing time is 45minutes.) trouble. If these error letters are displayed, please refer to the troubleshooting page27~28and follow the guide. 23 aintenance M Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. The water inlet filter " -" error detergent message will blink If your water is very hard - on the control panel when water does not enter the drawer. or contains traces of lime deposit, the water inlet filter may become It is clogged. therefore a good idea to clean it from time to time. 2. Unscrew the 1. Turn off the water water inlet tap. hose. 3. Clean the filter 4. using Tighten up the inlet a hard bristle hose. brush. The drain pump filter The drain filter collects threads and small Check 1. regularly that the Open the lower cover cap( )byusinga 2. filter is clean to objects left in the smooth ensure Unplug the drain plug ( ), allowing the water to flow out. laundry. running of your machine. 3. Remove any At coin. Turn the drain this time plug( )topullout water the hose. water does not flow any more, turn plug ( the pump filter close the lower use a flowing vessel to on prevent to the floor. When ( ) open to the left. cleaning, material foreign from the pump filter ( ). )to the original place. cover 3 1 ! ? ? ? 2 using the drain hose and then open the pump filter to whatever any threads or objects. Be careful when draining if the water is hot. Drain pump filter is to be cleaned 24 2 Caution First drain frequently. ( ) clockwise and insert the drain 100 3 After turn the pump filter remove cap. aintenance M Dispenser After a while drawer detergents and fabric softeners leave deposit It should be cleaned from time to time with a ? If necessary it from the machine can be removed completely running in the drawer. water. by pressing the catch downward and ? To facilitate by pulling it out. cleaning, the upper part of the jet of a ? fabric softener compartment can be removed. max max The drawer Detergent can be cleaned ? also accumulate inside the cycle The without washing If you live in seen with occasionally Once you have finished rinse ? recess a recess old toothbrush. an cleaning, replace the drawer and run a laundry. drum hard water area, limescale may and thus not which should easily continuously build up in places where it cannot be removed. Over time the build up of scale clogs appliances, and if it is not kept in check these may have to be replaced. ? Although the washing drum is made of Stainless steel, specks of rust articles (paper clips, safety pins) which have been left in the drum. ? The ? If you washing use can be caused by small metal drum should be cleaned from time to time. descaling agents, dyes or bleaches, make sure they are suitable for washing machine use. Descaler may contain chemicals that may Remove any Never use spots with a stainless steel damage part of your washing machine. cleaning agent. steel wool. 25 aintenance M Cleaning your washer 1. Exterior of your washer can extend its life. The outside of the machine can be cleaned with Proper care household detergent. off any Immediately wipe not to hit surface with Try water and a neutral non abrasive warm IMPORTANT: Do not spills. Wipe with damp cloth. sharp objects. methylated spirits, use diluents or similar products. 2. Interior Dry around the washer door Run washer through a opening, flexible gasket and complete cycle using hot water. Repeat process if necessary. NOTE Remove hard water deposits using only door glass. cleaners labeled as washer safe. Cold condition If the washer is stored in temperatures, an area 1. Turn off water Plug 4. Add freezing may occur or prevent damage moved in freezing to the washer: supply tap. 2. Disconnect hoses from water 3. where follow these instructions to electrical cord into 1gallon(3.8L) a supply and drain water from hoses. properly grounded of nontoxic recreational electrical outlet. vehicle(RV) antifreeze into an empty wash drum. Close the door. 5. Set spin cycle and let washer spin Not all of the RV antifreeze will be 6. Unplug electrical power 7. Remove 9. To remove through 26 a an expelled. cord, dry the drum interior, and close the door. dispenser drawer, 8. Store washer in for 1minute to drain out all water. drain and dry excessive water from the upright position. antifreeze from washer after storage, complete cycle using detergent. run empty washer Do not add wash load. compartments. T roubleshooting guide This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. When the machine does not function properly or does not function at all, check the following points before you contact your service provider. Possible Cause Symptom Rattling and clanking noise ? Solution Foreign objects such as coins safety pins maybe in drum or or Stop washer and check drum and drain filter. If noise continues after washer pump. is restarted, call your authorized service centre. Thumping Vibrating sound noise ? ? a Heavy wash loads may produce thumping sound. This is usually probably normal. redistribute wash load. Have all the transit bolts and packing ? the If not removed been removed? Are all the feet If sound continues, washer is out of balance. Stop and during installation, refer resting firmly on for removing to Installation Wash load may be distributed ground? in drum. guide transit bolts. unevenly Stop washer and rearrange wash load. Water leaks. ? Fill hoses at ? tap or or drain hose are loose Check and hose connections. tighten washer. House drain pipes are clogged. Unclog drain pipe. Contact plumber if necessary. Too much Oversudsing detergent detergent may foaming which or cause unsuitable excessive may result in water leaks. Water does not enter washer or ? it enters slowly Water supply is not adequate in Check another tap in the house. area. ? Water supply tap completely open. is not ? Water inlet ? The filter of the inlet hose(s) are Fully kinked. hose(s) are open tap. Straighten hose(s). Check the filter of the inlet clogged. Water in the washer does not drain drains slowly. ? Drain hose is kinked ? The drain filter is or clogged. or clogged. Clean and straighten hose(s). the drain hose. Clean the drain filter. 27 roubleshooting guide T Possible Cause Symptom Washer does not start ? Electrical power cord may not plugged in or connection be Solution Make fits plug sure tightly in wall outlet. may be loose. ? House fuse blown, circuit Reset circuit breaker breaker Do not increase fuse tripped,or a power outage has occurred. If problem is it corrected ? Water supply tap is not turned Turn on fuse. circuit overload, have a qualified electrician. a by water replace capacity. or supply tap. on. Washer won't spin Check that the door is shut. firmly Close the door and press the Start/Pause button. After pressing the Start/Pause button, it may take a few moments before the clothes washer begins to spin. The door spin can be must lock before achieved. Door does not open Once started, the door can not be for safety reasons. opened Wait one or two minutes before opening the door to give the electric locking mechanism time to release. Wash cycle delayed time The washing time may vary by the laundry, water amount of pressure, water temperature and other using conditions. If the imbalance is detected suds or if the removing program works, the wash time shall be increased. Dry problem ? Does not dry Do not overload. Check that the washer is properly to extract draining adequate water from the load. Clothes load is too small to tumble property. Add 28 a few towels. T roubleshooting guide Possible Cause Symptom ? Water ? Water ? ? Solution supply is not adequate in area supply taps are not completely open. Water inlet hose(s) are The filter of the inlet kinked. hose(s) are Check another tap in the house. Fully open tap. Straighten hose(s). Check the filter of the inlet hose(s). clogged. ? Drain hose is kinked Clean and ? The drain filter is Clean the drain filter. ? Load is too small. Add 1 ? Load is out of balance. balance the load. ? The has an unbalance detection and correction system. If individual are heavy articles or straighten the drain hose. 2 similar items to Rearrange spinning help load to allow proper loaded etc.), this system may stop spinning or even interrupt the spin cycle altogether. If the laundry is still too wet at the end of the cycle, add smaller articles of laundry to balance the load and repeat the spin cycle. (ex. ? appliance or clogged. clogged. bath mat, both robe, ? Is the door Close the door. opened? If " "is not released, call for service. Unplug the power plug and call for service. ? Water overfills due to the faulty water valve. Close the water tap. Unplug the power Call for service. ? Water level ? Over load in motor. ? Over load in motor. ? Check water sensor plug. has malfunctioned. supply. Turn the water tapon. If " power "is not released, plug unplug and call for service. 29 T erms of Warranty What Is Not Covered: ? ? ? ? Service trips to your home to teach you how to use the If the product rating plate. is connected to any voltage product. other than that shown the Act of God. If the fault is caused by accident, neglect, misuse If the fault is caused by factors other than normal domestic or on use or use in accordance with the owner's manual. ? ? ? Provide instruction on use If the fault is caused Noise or product or change by pests for example, Correcting or the set-up of the product. rats or cockroaches etc.. vibration that is considered normal for sound, spin sound, ? of example water drain warming beeps. the installation for example, levelling the of product, adjustment drain. ? ? Normal maintenance which recommended Removal of foreign objects by the owner's manual. / substances from the machine, including the example, grit, nails, bra wires, buttons etc. pump and inlet hose filter for ? ? ? ? Replace fuses in or correct house Correction of unauthorized Incidental wiring or correct house repairs. consequential damage to personal property possible defects with this appliance. If this or product plumbing. caused by is used for commercial purpose, it is not warranted. (Example : Public places center, dormitory) such as public bathroom, lodging house, training If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the replacement defective part, shall be borne by the owner. 30 of a P/No.: 3828ER3012L
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
Frequently Answers and Questions
What is the maximum wash capacity of the LG WD-14120RD?
The maximum wash capacity of the LG WD-14120RD is 7 kg.
What is the maximum spin speed of the LG WD-14120RD?
The maximum spin speed of the LG WD-14120RD is 1400 RPM.
What is the water consumption of the LG WD-14120RD?
The water consumption of the LG WD-14120RD is 75 liters per wash cycle (10.7 liters per kg of clothes).
What is the permissible water pressure for the LG WD-14120RD?
The permissible water pressure for the LG WD-14120RD is 0.3-10 kgf/cm² (30-1000 kPa).
What is the permissible cold water temperature for the LG WD-14120RD?
The permissible cold water temperature for the LG WD-14120RD is 4-25°C.
Does the LG WD-14120RD have a Child-Lock system?
Yes, the LG WD-14120RD has a Child-Lock system to prevent children from changing the program during operation.
Does the LG WD-14120RD have an Auto Restart feature?
Yes, the LG WD-14120RD has an Auto Restart feature that automatically restarts the washing cycle from where it stopped in case of a power failure.