LG | WD12570FD | LG WD12570FD Owner’s Manual

Washing Machine
OWNER'S MANUAL
WD12570FD
WD12576FD
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner's manual carefully, it provides
instructions on safe installation, use and maintenance.
Retain it for future reference.
Record the model and serial numbers of your washing
machine.
P
추가선택, 예약,
C
roduct Feature
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
Water Circulation
Sprays detergent solution and water onto the load over and over.
Clothes are soaked more quickly and thoroughly during wash cycle.
The detergent suds can be removed more easily by the water shower during rinse
cycle. The water circulation system uses both water and detergent more efficiently.
Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load
and unload clothing more easily.
Steam Washing and Refresh
Steam Washing features upgraded washing performance with low energy and
water consumption. Refresh Cycle removes wrinkles from dry clothes.
Eco Dry
When this option is selected, Eco dry function allows less water to be used during
the drying cycle in comparison to the conventional drying cycle.
RollerJets
Washing ball enhances the wash performance and reduces damage
to the clothing. The jets spray and help tumble clothes to enhance
washing performance while maintaining fabric care.
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
Built-in Heater
Internal heater helps to maintain water temperature at its optimum level for selected
cycles.
Child Lock
The Child lock prevents children from pressing any button to change the settings
during operation.
ontents
Warnings ......................................................................................................................3
Specification...................................................................................................................5
Installation......................................................................................................................6
Care before washing....................................................................................................12
Adding detergent..........................................................................................................13
Function
....................................................................................................................14
How to use washer ......................................................................................................15
Maintenance ................................................................................................................25
Troubleshooting guide .................................................................................................28
Terms of Warranty .......................................................................................................32
2
W arnings
READ ALL INSTRUCTIONS BEFORE USE
!
WARNING!
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance
is used by or near children or infirm persons.
Do not allow them to play on, with, or inside this
or any other appliance.
• Keep washer away from fire.
• Do not leave the washer door open.
An open door could entice children to hang on
the door or crawl inside the washer.
• Never reach into washer while it is moving. Wait
until the drum has completely stopped.
• The laundry process can reduce the flame
retardant of fabrics.
• Do not wash or dry articles that have been
cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry
cleaning solvents, kerosene, etc.) which may
ignite or explode. Oil may remain in the tub after
a whole cycle resulting in fire during drying. So,
do not load oiled clothes.
• Always follow the fabric care instructions
supplied by the garment manufacturer.
• Do not slam the washer door closed or try to
force the door open when locked. This could
result in damage to the washer.
• To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
• Dryer is intended for only drying textile material.
• If the washer has been exposed to water, call an
authorized service provider to avoid any risk of
fire or electric shock.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
WARNING
:
Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
3
W arnings
To minimize the risk of fire in a tumble dryer, the following should be observed:
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire
hazard and should not be placed in a tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat
sources Such as in a tumble dryer. The items become warm, causing an oxidation
reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can
become hot enough to catch fire. Piling, stacking or storing oil-affected items can
prevent heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been
contaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra detergent-this will reduce, but not eliminate, the
hazard. Washed in hot water with extra detergent-this will reduce, but not
eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to
reduce the temperature of the items. They should not be removed from the tumble
dryer or piled or stacked while hot.
• Items that have been previously cleaned in, washed in, soaked in or spotted with
petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances
should not be placed in a tumble dryer.
Highly flammable substances commonly used in domestic environments include
acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some
brands), turpentine, waxes and was removers.
• Items containing foam rubber (also known as latex foam) or similarly testured
rubber. like materials should not be dried in a tumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
• Fabric softeners or similar products should not be used in a tumble dryer to eliminate
the effects of static electricity unless this practice is specifically recommended by the
manufacturer of the fabric softener or product.
• Undergarments that contain metal reinforcements should not be placed in a tumble
dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during
drying. When available a drying rack could be used for such items.
• Plastic articles such as shower caps or babies waterproof napkin covers should not
be placed in a tumble dryer.
• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and
rubber-coated tennis shoes should not be placed in a tumble dryer.
4
S
pecification
Inlet Hose
Iron
Name
: Front loading washing machine
Power supply
: 220-240V~, 50Hz
Size
: 686mm(W) x 767mm(D) x 982(H)
Weight
: 94kg
Wash capacity
: 10kg(2200W)
Dry capacity
: 6kg(2150W)
Max. Watt
: 2200W
Spin speed
: No Spin/400/800/1000/1200
Water consumption
: 86 (8.6 / kg )
Permissible water pressure
: 7.3 ~ 116 PSI (50 ~ 800 kPa)
The external hot water supply must not exceed 70°C
Permissible cold water temperature : 4-25˚C
TT : Appliance complies with the requirement by certification Type Test Mark.
No further backflow protection required for connection to the water supply.
❋ The appearance and specifications may be varied without notice to improve the units quality.
❋ Specifications subject to change by manufacturer.
Accessories
Inlet hose(2EA)
Spanner
5
I
nstallation
Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other
vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at
all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the
appliance guarantee.
Transit bolts
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be
removed before using the washer.
When unpacking the base, be sure
to remove the additional packing
support in the middle of the base
packing.
Washer
Packing Support
Base Packing
Removing transit bolts
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts along with the rubber bungs.
3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future use.
• If they are not removed, it may cause heavy
vibration, noise and malfunction.
• Whenever the appliance is transported, the
transit bolts must be refitted.
2. Unscrew the 4 bolts with
the spanner supplied.
4. Close the holes with the caps supplied.
6
I
nstallation
Installation place requirement
Drain Hose
Washer
Laundry
Tub
approx.
2cm
Level floor :
Allowable slope under entire washer is 1°
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance :
The following clearances should be adhered to.
(10cm : rear / 2cm : right & left side)
Do not place or store laundry products on top of washer at
any time.
They can damage the finish or controls.
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
• Before placing the washer on tiles, apply a rubber mat under the feet.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the
washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an insulating(85x60cm)
covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown.
• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable,
and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top.
BS Plug Safety Details (For U.K. User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This appliance must be earthed
Green and Yellow(Earth)
Brown(Live)
Blue(Neutral)
E
L
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E
or by the earth symbol
or coloured Green or Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red.
If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
7
I
nstallation
Electrical connection
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or
similarly qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses
may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below
freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing
machine at room temperature for a few hours before putting it into operation.
CAUTION
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
Washing Machine is to be connected to the water mains using new hose-sets and that old
hose-sets should not be used.
Connecting water supply hose
Water supply pressure must be between 50kPa and 800kPa
(0.5~8kgf/cm2)
Don’t strip or crossthread when connecting Inlet hose to the valve.
If the water supply pressure is more than 800kPa, a decompression
device should be installed.
• Two rubber seals are supplied with the water inlet hoses these
are in order to prevent water leaks.
• Check water tightness of washing machine connections by
turning the tap completely on.
• Periodically check the condition of the hose and replace the
hose if necessary.
• Make sure that there is no kink on the hose and that it is not
crushed.
When your washer has two valves,
• The Inlet hose which has red connector is for the hot water tap.
• If the washer then two valves, the energy is saved by using hot
valve.
8
I
nstallation
Normal Tap without thread & screw type inlet hose
1. Unscrew the fixing screw to
attach the tap.
2. Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.
3. Push the water supply hose
vertically upwards so that the
rubber packing within the hose
can adhere completely to the tap
and then tighten it by screwing it
to the right.
Normal Tap without thread & one touch type inlet hose
1. Loosen the upper connector
screw.
Upper
Connector
Fixing screw
Rubber
packing
Middle
connector
• In case the diameter of the tap is
large remove the guide plate.
Guide plate
2. Push the upper connector up till 3. Connect the water supply hose
the rubber packing is in tight
contact with the tap. Then
tighten the 4 screws.
Upper
Connector
Rubber packing
Plate
Upper
Connector
Water supply
hose
Middle
connector
• Turn the middle connector to
eliminate water leaked.
Connector
to the middle connector,
pushing the plate down.
• Make sure that the rubber seal
is inside the hose connector.
• To separate the water supply
hose from the middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate down.
Hose connector
Rubber seal
Used the horizontal tap
Horizontal tap
Extension tap
• Your machine comes with only
cold water connection.
• Make sure that there are no
kinks in the hose and that it is
not crushed.
Square tap
9
nstallation
I
This equipment is not designed for maritime use or for use in mobile installations such as
caravans, aircraft etc.
Turn off the tap if the machine is to be left for any length of time (e.g. holiday), especially if
there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the Plug.
Disable the door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation ! Keep all packaging well away from children
Installation of drain hose
about 100 cm
min. 60 cm
max. 100 cm
about 145 cm
• When installing the drain hose to a sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage should the drain hose
become loose.
about 105 cm
Laundry tub
about 100 cm
Hose
Retainer
max. 100 cm
about 105 cm
min. 60 cm
about 145 cm
• The end of the drain hose should not be placed
higher than 100 cm above the floor.
• Proper securing of the drain hose will protect the
floor from damage due to water leakage.
• When the drain hose is too long, do not force
back into the washer. This will cause abnormal
noise, malfunction, and water leakage.
10
max. 100cm
min. 60cm
Tie
strap
max. 100cm
min. 60cm
I
nstallation
Level adjustment
1. Adjusting the washing machine level properly prevents excessive
noise and vibration.
Install the appliance on a solid and level floor surface, preferably in
a corner of the room.
NOTE
Timber or suspended type flooring may contribute to
excessive vibration and unblance errors.
2. If the floor is uneven, adjust the adjustable feet as required. (do
not insert pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use a spirit level)
After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
NOTE
In the case that the washing machine is installed on a raised
platform, it must be securely fastened in order
to eliminate the risk that it might fall off.
❊ Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the
machine should not move up and down at all. (Please, check both of two directions)
If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
Concrete floors
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.
Tile floors (Slippery floors)
• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm
sections and stick the pieces on to the dry tile where machine is to be placed.)
Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.
Wooden floors (Suspended floors)
Rubber Cup
• Wooden floors are particularly susceptible to vibration.
• To reduce, vibration we recommend you place rubber cups under each foot,
It can be purchased from
hardware suppliers.
at least 15mm thick under the washer, secured to at least 2 floor beams with screws.
• If possible install the washer in one of the corners of the room, where the floor is more stable.
Insert the rubber cups to reduce vibration.
Rubber cups ( p/no. 4620ER4002B ) can be purchased from the LG spare parts department.
Important!
• Proper placement and levelling of the washer ensures long, regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
11
C
are before washing
Before the first washing
Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash
without clothing.
This will remove residues from the drum that may have been left during manufacturing.
Caring before washing
1. Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your
garment and how it should be washed.
2. Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint
transfer can occur causing discoloration of white etc. If possible, do not wash heavily
soiled items with lightly soiled one.
Soil (Heavy, Normal, Light)
Color (White, Lights, Darks)
Lint (Lint producers, Collectors)
Separate clothes according to amount of soil.
Separate white fabrics from colored fabrics.
Wash lint producers and lint collectors
separately.
3. Caring before loading
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
• Check all pockets to make sure that they are
empty. Items such as nails, hair clip, matches,
pens, coins and keys can damage both your
washer and your clothes.
• Close zippers, hooks and strings to make sure
that these items don’t snag on other clothes.
• Do not be stuck between the door and the
glass.
• Pre treat dirt and stains by brushing a little
detergent dissolved in water onto stains like
collars and cuffs to help shift dirt.
• If you wash underwear, use the wash cloth
bag. If you don’t use the wash cloth bag while
washing the underwear, wires in the bra may
make a noise.
12
A dding detergent
Adding detergent and fabric softener
3. Detergent dosage
1. The Dispenser Drawer
MAX
• The detergent should be used according to the
instruction of the detergent manufacture.
MAX
MAX
max
max
max
MAX
• If too much detergent is used, too many suds
can occur and this will decrease the washing
result or cause heavy load to the motor.
(Causing malfunctions)
max
for
sh
Fabric
softener
Detergent for
main wash
)
Detergent
for
(
)
main wash
(
)
Fabric
for
( Detergent
) Detergent
)
Fabric
for(
softener
softener
main washpre wash
(
• Main
wash
only ➔Detergent for
Fabric
Detergent
for
main wash
softener
• If there are too many suds, the detergent
quantity must be reduced.
Detergent for
pre wash
()
)(
( )
pre wash
)
)
(
)
• Pre( Wash
+( Main
Wash
➔
2. Adding Fabric Softener
• Do not exceed the maximum fill line.
Overfilling can cause early dispensing
of the fabric softener which could stain
clothes.
Detergent for
• Use
specified Front loader washing powder
pre wash
only.
)
(
)
• Detergent usage may need to be adjusted
for water temperature, water hardness,
size and soil level of the load. For best
results, avoid oversudsing.
❋ Tips
Full load : according to
manufacturer’s recommendation.
Part load : 3/4 of the normal amount.
Minimum load : 1/2 of full load.
• Detergent is flushed from the dispenser at
the beginning of the cycle.
• Do not leave the fabric softener in the
detergent drawer for more than 2 days.
(Fabric softener could harden)
• Softener will automatically be added
during the last rinse cycle.
• The soap drawer can be partially
opened to add pre dissolved soap
powder during the initial fill.
• Solvents(benzene, etc) are not
allowable.
NOTE
Do not pour fabric softener
directly on the clothes
13
F
unction
Recommended courses according to the laundry type
Program
Cotton
Synthetic
Fabric Type
Color fast garments
(shirts, night dresses,
pajamas...)and lightly soiled
white cotton (underwear...)
60˚C
(Cold,
30˚C, 40˚C,
95˚C)
Polyamide, Acrylic,
Polyester.
40˚C (Cold,
30˚C, 60˚C)
Baby Care Lightly soiled baby wear
Allergy Care
Refresh
Duvet
Cotton
Quick
95°C
(Cold, 30°C,
40°C, 60°C)
Additional
Option
Maximum
Load
Pre Wash
Rinse+Spin
Dry Only
Less Steam
Eco Steam
Turbo Steam
Intensive
Rating
5.0kg
6.0kg
For clean wash through
eliminate allergy source.
60°C
Turbo Steam
Intensive
5.0kg
Cotton mixed, Polyeter
mixed Dress shirts, blouses
(It just makes wrinkled
clothes easy to iron)
60°C
Turbo Steam
5 items
40˚C
(Cold, 30˚C)
Rinse+Spin
Intensive
3.0kg
Colored Landry which is
lightely soiled fast.
30°C
(Cold, 40˚C)
Rinse+Spin
Dry Only
Intensive
5.0kg
Cotton bedding with filling,
duvet, pillow, blanket, sofa
cover with light filling.
40˚C
(Cold, 30˚C)
Rinse+Spin
Intensive
1 king size
(9 Tog)
Cotton Which is lightly
soiled.
40˚C
(Cold, 30˚C,
60˚C)
Pre Wash
Rinse+Spin
Less Steam
Eco Steam
Turbo Steam
Intensive
Rating
“Hand Wash” marked
Hand Wash
laundry or machine
/Wool
washable woolens.
Quick 30
Proper Temp.
(Option)
❋ Water Temperature : Select the water temperature to the wash cycles.
Always follow garment manufacture’s care label or instructions when
laundering.
❋ Intensive : When washing full load or heavily soiled laundry, you can increase effectiveness by
choosing intensive option.
❋ Pre Wash : If the laundry is heavily soiled, “Pre Wash” option is recommended.
Pre Wash is available in Cotton, Synthetic and Baby Care Program.
14
H ow to use washer
1. Cotton automatically
selected upon power on.
• Press the Power(
) button to start.
• Press the Start/Pause(
• Initial condition
- Rinse : Normal
- Water temperature : 60°C
- Spin : 1200 rpm
- Program : Cotton
) button.
2. Manual Selecting
• Press the Power(
washer on.
) button to turn the
• Select the desired cycle with the
program dial and if required, make any
changes to the washing conditions by
pressing the buttons accordingly.
For selecting the each conditions, please
refer to the page16~page24
• Press the Start/Pause button to
commence the cycle.
15
H ow to use washer
(1)
(2)
(1)Button: Power
(2)Dial: Program
(3)Button: Start/Pause
(4)Button: Option
(3)
(4)
(5)Child lock
(6)Button: Rinse
(7)Button: Temperature
(8)Button: Intensive
Power
(5)
(6) (7)
(8, 9, 10)
(9)Button: Tub Clean
(10)Button: Time Delay
(11)Button: Spin
(12)Button: Turbo Steam
(11) (12)
(13)
(13)Dial: Dry
Program
1. Power
• Press the Power(
on and off.
) button to turn power
• To cancel the Time Delay function, the
Power( ) button should be pressed.
• 9 programs are available according to the
laundry type.
2. Initial Program
• Lamp will light up to indicate selected
program.
• When the Power( ) button is pressed, the
washer is ready for Cotton program. And the
other initial conditions as follows.
• When Start/Pause( ) button is pressed,
the Cotton program is automatically selected.
• So, if you want to advance into the washing
cycle without changing the program, just
press Start/Pause( ) button and then the
washer will proceed.
■ Initial program
- Cotton Program / Rinse:Normal / 60°C/
1200rpm
16
- By turning the Program dial, the program is
Selected in order of “Cotton – Cotton Quick –
Synthetic – Duvet – Hand Wash/Wool –
Quick 30 – Refresh – Allergy Care –
Baby Care
For information regarding laundry type for
each program, please refer to page 14.
H ow to use washer
Start/Pause
Option
• By pressing the option
button, only one option
functions may be selected.
1. Start
• This Start/Pause button is used to start
wash cycle or pause the wash cycle.
NOTE:
Depending on the selected
program cycle, not all
Options may be selectable.
2. Pause
1. Pre Wash
• If temporary stop of wash cycle is needed,
press “Start/Pause” button.
• Use this option for loads that need
pretreatment. This adds 17 minutes of pre
washing before draining.
• When in Pause, the power is turned off
automatically after 4 minutes.
- When using Pre Wash option, do not use a
liquid detergent for the main wash.
Use powder for the main wash.
• Available in Cotton, Cotton Quick, Synthetic
and Baby Care.
2. Rinse + Spin
• Use this option to rinse and then spin
3. Dry Only
• When you want dry only, select the this
option. Available in Baby Care, Cotton,
Cotton Quick, Synthetic and Quick30.
4. Less Steam
• When you want to do a steam wash for
only a small amount of laundry, select the
this opton.
5. Eco Steam
• When you want to do a steam wash for
reducing the electricity consumption, select
the this opton.
17
H ow to use washer
Child lock
Rinse
• By pressing the Rinse
button, the Rinse type can
be selected.
If you choose to lock the buttons on the
control assembly to prevent tampering, this
function may be selected.
• Child lock can be set by pressing and
holding the Option and Rinse button
simultaneously. (About three seconds)
- Normal
- Rinse+
- Medic Rinse
- Normal+Hold
- Rinse++Hold
1. Normal
• Allergy Care, Baby care performs 4 Rinses.
• Cotton, Synthetic, Duvet, Hand Wash/Wool
performs 3 Rinses
• When child lock is set, all buttons are inoperable
except for power button.
• When child lock is set,
and remaining
time are displayed by turns.
• To deactivate Child lock system, press and
hold the Option and Rinse button
simultaneously again. (About three seconds)
• Cotton Quick, Quick 30 performs 2 Rinses.
2. Rinse+ & Medic Rinse
• Used to additional rinse, which may assist in
removing traces of detergent residue.
• By selecting Rinse+ or Medic Rinse
function, the Rinse Time and the Rinse
water are increased.
• Medic Rinse includes water heating in the
last rinse.
• To change to the desired program, whilst in
child lock mode.
1. Press and hold both Option and Rinse
button together once again.
(About three seconds)
2. Press the Start/Pause button.
3. Select the desired program and press the
Start/Pause button again.
Change
the desired
program
• The child lock can be set at any time and it
is automatically canceled when operational
errors occur.
18
3. Rinse Hold
• Is selected by pressing the Rinse button
repeatedly this function leaves clothes in the
washer; suspended in the water after a rinse
without entering into spin.
• To proceed to a Drain or Spin function after
a Rinse hold, select Drain on the program
dial or press the Spin selector button to the
desired speed, then press the Start/Pause
button.
The required lamp will light up for
identification.
H ow to use washer
Spin
• By pressing the Spin button,
the spin speed can be
chosen.
Water Temperature
• By pressing the Temp.
button, the water
temperature can be
selected.
- Cold
- 30˚C / 40˚C / 60˚C / 95˚C
1. Spin selection
• Water temperature can be selected as
below according to the program.
• Spin speed is available according to the
program as follows.
- Cotton, Baby Care
Cold – 30°C – 40°C – 60°C – 95°C
- Cotton & Cotton Quick & Quick30
No Spin – 400 – 800 – 1000 – 1200
- Synthetic & Cotton Quick
Cold – 30°C – 40°C – 60°C
- Allergy Care & Baby Care & Synthetic &
Duvet
No Spin – 400 – 800 – 1000
- Duvet & Hand Wash/Wool & Quick30
Cold – 30˚C – 40˚C
- Hand Wash/Wool
No Spin – 400 – 800
- Allergy Care & Baby Care
60°C
2. No spin
The required temperature lamp will light up for
identification.
• If “No Spin” is selected, the washer stops
after draining water.
For the more detailed information, please refer
to the page14.
The required lamp will light up for
identification.
19
H ow to use washer
Tub Clean
Time Delay
Tub Clean course can be set by pressing
‘Tub Clean’ button.
TUB CLEAN is special cycle to clean the
inside of the washer. This cycle uses higher
water level with higher spin speed. Perform
this cycle regularly.
How to use the Tub Clean cycle:
1. Remove any clothing or items from the
washer and close the door.
2. Open the dispenser drawer and add Anti
limescale (Calgon) to the Main wash
compartment.
NOTE: Do not add any detergent to the
detergent compartments. Excessive
suds may generate and leak from the
washer.
3. Close the dispenser drawer slowly.
Preparing washing before starting “Time Delay”
- Turn on the water tap.
- Load laundry and close the door.
- Place the detergent and fabric softener in
the drawer.
• How to set “Time Delay”
- Press Power(
) button.
- Turn the Program dial to select
the program you require.
- Press Time Delay button and set the
desired time.
- Press the Start/Pause(
) button.
(“
” lamp is blink)
4. Power On and then press ‘Tub Clean’
5. Press the Start/Pause button to start.
6. After the cycle is complete, leave the door
open to dry around the washer door
opening, flexible gasket and door glass.
! CAUTION: If there is a small child, be
careful not to leave the door
open for too long.
• If Time Delay button is pressed, “3:00” is
displayed. The maximum delayed time is
19:00 hours and the minimum time is 3:00
hours.
• Each pressing of the button advances time
delay by one hour.
• To cancel the time delay, press the
Power(
) button.
• Time Delay is ‘expected time’ from the
present to the completion of washing cycle
or selected process (Wash, Rinse, Spin).
• According to the condition of water supply and
temperature, the delayed time and the actual
washing time may vary.
20
H ow to use washer
Intensive
Refresh
■ Refresh cycle
• When washing full load or heavily soiled
laundry, you can increase effectiveness by
choosing intensive option.
• For slightly wrinkled clothes which have
been stored for an extended time.
It just makes wrinkled clothes easy to iron
(Do not load wet clothes).
• Wrinkles will be reduced.
■ How to use Refresh cycle
• By selecting the Intensive option, the wash
time may be extended, depending on the
program selected.
1. Turn on the washer and select the Refresh
program.
• To use this option press the Intensive button
once before the wash program is started.
3. Press the Start/Pause button.
Turbo Steam
• For tough stained clothes,
underwear, or baby clothes.
• Steam Wash is available with
Baby Care, Allergy Care,
Cotton, Cotton Quick,
Synthetic, Refresh.
• This option features upgraded washing
performance with low energy and water
consumption.
• Do not load delicates such as wool, silk,
and easily discolored clothes.
NOTE:
- Steam wash is a highly concentrated and
efficient. It may seem there is no water
inside the drum, but this is normal.
- Steam spray may not be seen clearly
through the door; however, the washer is
spraying steam strongly inside.
- During the steam operation, a spraying
sound will be heard. This is not a
malfunction.
! CAUTION: Do not reach into the washer
while operating. Steam can
cause severe burns.
2. Load 5 items or less and close the door.
[Precautionary Notes]
- The Refresh cycle is not like other washing or
drying cycles.
- After the Refresh cycle is complete, the
washer will tumble the clothes for up to 30
minutes to prevent rewrinkling.
- Due to the characteristic of cotton fibers, this
cycle is not recommended for 100% cotton
clothing.
- Remove stains from clothing before using the
Refresh cycle to prevent permanently setting
the stains by high heat.
- Be sure that the faucet is open. This cycle
uses a little water to produce steam.
- Be careful not to touch the door. It can be
very hot.
- Do not open the door while operating.
Steam can cause severe burns.
- After removing clothes from the Refresh cycle
they may feel slightly damp wait at least 10
minutes before putting the clothes on.
- Best result are achieved when articles are of
similar size and fabric type. Do not overload
(Load less than 3 dress shirtes)
! CAUTION:
- Do not reach into the washer while
operating. Steam can cause severe burns.
- Keep pets away from the washer.
21
H ow to use washer
Dry
NOTE
The maximum drying capacity for this
model is 6kg. When loading, please
use the maximum drying capacity
indicator behind the door as shown
below.
1.Drying Automatic guide
• Use your Automatic Cycles to dry most loads.
Electronic sensors measures the temperature
of the exhaust to increase or decrease drying
temperatures for faster reaction time and
tighter temperature control.
• Recommend Automatic drying course for
clothes type.
a) For Synthetics select – Low Temp.
b) If you want to iron clothes – Iron.
c) For Cottons select – Normal, Eco
d) For washable nappies select – More
Dry-Eco is special cycle to save water for dry.
If you select this course, you can save a water.
But drying time is longer about 1hours than
cotton drying time.
• Do not overload above the maximum drying
capacity indicator. Items must be able to
tumble freely.
• This washer-dryer’s automatic process from
washing to drying can be selected easily.
• For most even drying , make sure all articles
in the clothes load are similar in material
and thickness.
• If you open door and remove load before
dryer has finished its cycle, remember to
press the Start/Pause button.
• By turning the dial, you can select.
Normal ➔ More ➔ 30 ➔ 60 ➔ 90 ➔ 120 ➔
150 ➔ Low Temp➔ Iron➔ Eco
• After the end of dry, “
” is displayed.
By pressing the “Start/Pause” button the
program can be ended. If you not press the
“Start/Pause” button, the “
” cycle will end
automatically after 4 hours.
22
NOTE: The estimated drying time varies
from the actual drying time with an
Automatic. The type of fabric, size of the load,
and the dryness selected, do affect the drying
times.
❋ The standard laundry weight which shows
how much laundry to put into the washer.
Sorts of
laundry
Single
weight
Diaper
Shirt
Shortsleeved
100g
200g
300g
Sorts of
laundry
Single
weight
Underwear Nightclothes
50g
500g
Jean
1200g
H ow to use washer
2.Drying time guide
3.Completion of Drying
• By turning the Dry button, the drying time
can be selected.
• Drying course can last up to 150min. When
selecting drying only, drying course will
start after spining.
• These drying times are given as a guide to
help you set your dryer for manual drying.
Drying times can vary greatly depending on
dampness, room temperature and type of
fabric and your own experience will be your
best guide.
• When drying cycle is completed, “
” [Cool
Down] is displayed on the Multi display.
• The Cool Down is setting automatically when
a drying cycle is complete.
• Wrinkles and creases will form if the clothes
are not removed immediately after the drying
is completed.
• The Cool Down operating periodically
tumbles, rearranges and fluffs the load to
avoid wrinkles without heat for up to 4 hours.
• The “
” message will continue to display
until the clothes are removed or the
Start/Pause button is pressed within the 4
hours after the drying has been completed.
Woolen Articles
- Do not tumble dry woolen articles. Pull them
to their original shape and dry them flat.
- Some woven and loop knit materials may
shrinks, by varying amounts, depending on
their quality.
Door Lock
- Always stretch them not immediately after
drying.
Permanent Press and Synthetics
- Do not overload your dryer
• Lights whenever the door of the washer is
locked.
- Take out permanent press articles as soon
as the dryer stops to reduce wrinkles.
• The door can be unlocked by pressing the
Start/Pause button to stop the washer.
Fiber or Leather Materials
- Always check the manufacture’s instructions.
Baby clothes and Night Gowns
- Always check the manufacture’s instructions.
Rubber and Plastics
- Do not dry any items made from or
containing rubber or plastics, such as:
a) aprons, bibs, chair covers
b) curtains and table cloths
c) bathmats
• The door can be opened after a short delay.
Drum Light
• The Drum Light comes on when the Power
button is pressed. It goes off when the door
is closed and the washer starts operation.
• The Drum Light remains off when the door
is locked.
• The Drum Light comes on when the
washing cycle is finished and goes off 4~8
minutes later.
Fiber glass
- Do not dry fiberglass articles in your dryer.
Glass particles left in the dryer could be
picked up by your clothes the next time you
use the dryer and irri tate your skin.
23
H ow to use washer
Display
3. Completion of washing
• When washing cycle is completed, “
is displayed on the “Multi display”.
1. Special function display
4. Time left
• When Child lock is selected, the
“
” lamp is on.
• During washing cycle, the remaining
washing time is displayed.
• After the end of dry, “
• Recommended program by manufacturer.
” is displayed.
• When time delay is selected, it shows the
remaining times to finish the selected
program.
2. Self diagnose display
• If the washer encounters a fault during
operation, the associated fault will be
displayed.
”
- Refresh : around 20 minutes
- Baby Care :
around 3 hours and 02 minutes
- Allergy Care :
around 2 hours and 20 minutes
- Cotton : around 2 hours and 08 minutes
- Synthetic :
around 1 hour and 33 minutes
“
” : Water pressure sensing error
“
” : Problem of overfilling water
“
” : Door is not closed
- Cotton Quick :
around 1 hour and 06 minutes
“
” : Over load in motor
- Duvet : around 1 hour and 23 minutes
“
” : Water inlet trouble
“
” : Drainage trouble
- Hand Wash/Wool :
around 1 hour and 13 minutes
“
” : Unbalanced load
- Quick30 : around 30 minutes
“
” : Water temperature trouble
• The washing time may vary by the amount
of laundry, water pressure, water
temperature and other washing conditions.
“
” : Dry heater or thermostat trouble.
If these error letters are displayed, please refer to
the troubleshooting page31 and follow the guide.
24
• If an unbalanced load is detected or if the
suds removing program operates, the wash
time may be extended.
(Max. increasing time is 45 minutes.)
M aintenance
❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to
avoid electrical shock hazards.
❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door
lock to prevent young children being trapped inside.
The water inlet filter
-"
" error message will blink on the control panel when water does not enter the
detergent drawer.
- If your water is very hard or contains traces of lime deposit, the water inlet filter may
become clogged.
It is therefore a good idea to clean it from time to time.
1. Turn off the
water tap.
2. Unscrew the
water inlet
hose.
3. Clean the
filter using a
hard bristle
brush.
4. Tighten up
the inlet
hose.
The drain pump filter
❋ The drain filter collects threads and small objects left in the laundry.
Check regularly that the filter is clean to ensure smooth running of your machine.
! CAUTION
First drain the water using the drain hose and then open the pump filter to
remove tangled threads or foreign objects.
Be careful when draining if the water is hot.
❋ Allow the water to cool down before cleaning the drain pump, carrying out emergency
emptying or opening the door in an emergency.
1. Open the lower cover
cap ( ) by using a
finger.
2. Unplug the drain plug ( ),
allowing the water to flow out. At
this time use a vessel to prevent
water flowing on to the floor. When
water does not flow any more, turn
the pump filter ( ) open to the left.
3. Remove out any foreign material
from the pump filter ( ). After
cleaning, turn the pump filter ( )
clockwise and insert the drain
plug ( )to the original place.
close the lower cover cap.
3
3
2
2
25
M aintenance
Dispenser drawer
❋ After a while detergents and fabric softeners leave a deposit in the drawer.
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the catch
downward and by pulling it out.
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
The drawer recess
❋ Detergent can also accumulate inside the recess which should
be cleaned occasionally with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a
rinse cycle without laundry.
The washing drum
• If you live in a hard water area, lime scale may continuously build up in places where it cannot be
seen and thus not easily removed.
Over time the build up of scale clogs appliances, and if it is not kept in check, expensive
maintenance or repairs may result.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal
articles (paper clips, safety pins) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descalling agents, dyes or bleaches, make sure they are suitable for washing machine
use.
❋ Descaler may contain chemicals that may damage part of your washing machine.
❋ Remove any spots with a stainless steel cleaning agent.
❋ Never use steel wool.
26
M aintenance
The water circulation nozzle & steam nozzle
• Clean the water circulation nozzle, if clogged.
Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral non abrasive
household detergent.
Immediately wipe off any spills. Wipe with damp cloth.
Try not to hit surface with sharp objects.
❋ IMPORTANT: Do not use methylated spirits, diluents or similar products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass.
Run washer through a complete cycle using hot water.
Repeat process if necessary.
NOTE
Remove hard water deposits using only cleaners labeled as safe for washing
machine.
Winterizing instructions
If the washer is stored in an area where freezing may occur or moved in freezing
temperatures, follow these instructions to prevent damage to the washer:
1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into an empty wash drum.
Close the door.
5. Set spin cycle and let washer spin for 1minute to drain out all water.
Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry the drum interior, and close the door.
7. Remove dispenser drawer, drain and dry excessive water from the compartments.
8. Store washer in an up right position.
9. To remove antifreeze from washer after storage, run empty washer
through a complete cycle using detergent. Do not add wash load.
27
roubleshooting guide
T
❋ This washing machine is equipped with automatic safety functions which detect and
diagnose faults at an early stage and react appropriately.
When the machine does not function properly or does not function at all, check the
following points before you contact your service provider.
Symptom
Possible Cause
Solution
Rattling and
clanking noise
• Foreign objects such as coins or
safety pins maybe in drum or
pump.
Stop washer and check drum
and drain filter.
If noise continues after washer
is restarted, call your authorised
service centre.
Thumping sound
• Heavy wash loads may produce
a thumping sound. This is usually
normal.
If sound continues, washer is
probably out of balance. Stop and
redistribute wash load.
Vibrating noise
• Have all the transit bolts and
packing been removed?
• Are all the feet resting firmly on
the ground?
If not removed during
installation. Refer to Installation guide
for removing transit bolts.
Wash load may be unevenly
distributed in drum. Stop washer and
rearrange wash load.
Water leaks.
• Fill hoses or drain hose are loose
at tap or washer.
Check and tighten hose connections.
• House drain pipes are clogged.
Unclog drain pipe. Contact plumber
if necessary.
• There is something between
the gasket and the glass.
Clean the gasket and
the glass with the towel.
Over sudsing
Water does not enter
washer or it enters
slowly
28
Too much detergent or unsuitable
detergent may cause excessive
foaming which may result in water
leaks, and vibration during spin.
• Water supply is not adequate in
area.
Check another tap in the house.
• Water supply tap is not
completely open.
Fully open tap.
• Water inlet hose(s) are kinked.
Straighten hose.
• The filter of the inlet hose(s)
clogged.
Check the filter of the inlet hose.
T
roubleshooting guide
Symptom
Possible Cause
Solution
Water in the washer
does not drain or
drains slowly.
• Drain hose is kinked or
clogged.
Clean and straighten the drain hose.
• The drain filter is clogged.
Clean the drain filter.
Washer does not
start
• Electrical power cord may not
be plugged in or connection
may be loose.
Make sure plug fits tightly in wall
outlet.
• House fuse blown, circuit
breaker tripped,or a power
outage has occurred.
Reset circuit breaker or replace fuse.
Do not increase fuse capacity.
If problem is a circuit overload, have
it corrected by a qualified electrician.
• Water supply tap is not turned
on.
Turn on water supply tap.
❋ Check that the door is firmly
shut.
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the clothes
washer begins to spin. The door
must lock before spin can be
achieved.
Washer will not spin
Once started, the door can not be
opened for safety reasons.
Wait one or two minutes before
opening the door to give the electric
locking mechanism time to release.
Door does not open
Display stuck on
6min left.
This washing machine checks
the condition of the clothes at
6min left to evaluate if they are
dried or not. If the clothes are
not dried, the washing machine
will further dry for 30min. The
6min display will then continue
to count down after 30min.
Check the weight of clothes.
The weight of the clothes should be
less then 6kg.
Washer pauses for
longer intervals than
normal during
tumbling.
The bowl will tumble for 3
seconds and then pause for 50
seconds repeatedly for part of
the wash cycle. This is normal
during the Hand Wash & Wool
cycles.
This action allows the more delicate
clothes to soak which assists in stain
removal.
29
roubleshooting guide
T
Symptom
Wash cycle time
delayed
Possible Cause
• It takes time to balance the
laundry before the spin cycle
Solution
The washing time may vary by the
amount of laundry, water
pressure, water temperature and
other usage conditions.
If the imbalance is detected or if the
suds removing program works, the
wash time shall be increased.
Stop the wash and pull out the
laundry then put it again to untwist
Dry problem
30
• Does not dry
Do not overload.
Check that the washer is draining
properly to extract adequate water
from the load.
Clothes load is too small to tumble
property. Add a few towels.
T
roubleshooting guide
Symptom
Possible Cause
Solution
• Water supply is not adequate in area
• Water supply taps are not completely
open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are
clogged.
Check another tap in the house.
Fully open tap.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance
detection and correction system. If
individual heavy articles are loaded (ex.
bath mat, both robe, etc.), this system
may stop spinning or even interrupt the
spin cycle altogether.
• If the laundry is still too wet at the end
of the cycle, add smaller articles of
laundry to balance the load and repeat
the spin cycle.
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
• Is the door opened or
not completely closed?
Straighten hose(s).
Check the filter of the inlet hose(s).
Close the door completely.
❋ If “ ”is not released, call for service.
Unplug the power plug and call for service.
• Water overfills due to the faulty water
valve.
Close the water tap.
Unplug the power plug.
Call for service.
• Water level sensor has malfunctioned.
• Over load in motor.
• Check water supply.
Turn the tap on
If
is not released, unplug power
plug and call service.
31
T
erms of Warranty
What Is Not Covered:
• Service trips to your home to teach you how to use the product.
• If the product is connected to any voltage other than that shown on the
rating plate.
• If the fault is caused by accident, neglect, misuse or Act of God.
• If the fault is caused by factors other than normal domestic use or use in
accordance with the owner's manual.
• Provide instruction on use of product or change the set-up of the product.
• If the fault is caused by pests for example, rats or cockroaches etc..
• Noise or vibration that is considered normal for example water drain
sound, spin sound, or warning beeps.
• Correcting the installation for example, leveling the product, adjustment of
drain.
• Normal maintenance which is recommended by the owner's manual.
• Removal of foreign objects / substances from the machine, including the
pump and inlet hose filter for example, grit, nails, bra wires, buttons etc.
• Replace house fuses or correct house wiring or correct house plumbing.
• Correction of unauthorized repairs.
• Incidental or consequential damage to personal property caused by
possible defects with this appliance.
• If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training
center, dormitory)
If the product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement of a
defective part, shall be borne by the owner.
32
M emo
33
M emo
34
M emo
35
P/No.: MFL31245165
Download PDF

advertising