LG | WF-T6571 | LG WF-T6571 Owner’s Manual

roduct Features
Washer doesn't operate while the lid is open. If the lid is open during the wash,
rinse or spin cycles, the operation stops for safety.
● The sensor automatically detects the quantity of a Detergent put by a user and the temperature and
the quality of water to make the best washing algorithm for washing and rinsing, which can give
the best washing effect.
FUZZY logic control
● A built-in load sensor automatically detects the laundry load and a microprocessor optimizes
washing conditions such as ideal WATER LEVEL and washing time.
Laundry Sensor
Water Level Sensor
● Advanced technology is built into the Electronic Control System which ensures the best
washing result.
Turbo drum washing
● The "punch + 3" washing wings and the washing tub turn in opposite
directions. This makes the water current flow in two directions which
improves washing efficiency.
● The wash performance is also improved by the water which continually
cascades into the wash bowl from small waterfalls in the washing tub.
Innovated washing wings
● Three small washing wings generate strong and sharp washing currents
to clean laundry uniformly.
● Adjusted vertical movement and rotating direction of the washing action
reduces laundry entanglement and improves washing power.
3 Step washing
● 3 step washing makes the best washing performance with low tangling.
Rubbing and Shaking
Shaking and Disentangling
Device for removing lint
● Lint filter catches lint and threads generated during washing to keep
the laundry clean.
Connect the drain hose
● Connect the drain hose to the
● Attach the clip to the drain hose. And
● Place the hose guide over the
then push it toward the body of the
washing machine as
indicated by the arrow.
● Do not use an extension hose.
outlet of the drain pump located
at the rear of the washing
laundry tub or the stand pipe.
Within 50mm
❏ NOTE :
Hose Guide
● Never lay down the drain hose, as water will be discharged.
Drain Hose
● Be sure the drain hose is properly routed so it will not kink or lift from the sink.
● To prevent syphoning, the drain hose should not extend more than 50 mm
from the end of the hose guide.
● The discharge height should be approximately 0.9~1.2m from the floor.
✽ “ Washing machine is to be connected to the water mains using new hose-sets and that old hose-sets should not be
reused ”
Flooding drainage
● Your machine requires a floor drainage slope (or hole) that will SAFELY DISPOSE of the FULL FLOW of any
water that may leak out should the machine malfunction.
It is therefore the OWNER'S RESPONSIBILITY to make sure this machine is installed in an area with a drain hole
(or slope) that will prevent any possibility of water damage to floor coverings or property.
Connect the inlet hose
● Check that sealing washers are firmly seated.
● Attach the curved end of the hose to the inlet valve of the washing
machine; Tighten the coupling nuts securely by hand. (Fig. 1)
● Attach the straight end of the hose to the tap.
Tighten the coupling nuts securely by hand. (Fig. 2)
● Another hose can be attached to hot inlet valve and tap.
● Turn on the taps and check for leaks. Tighten the coupling nuts firmly
if there is any leakage. If water pressure is strong, close the water tap
completely then open it slightly.
(Fig. 1)
(Fig. 2)
● Do not install the washer where it is directly exposed to sunlight, wind, rain etc.
● Plug the power cord of this washer into a properly installed standard power point that is switched & earthed.
● Your machine requires a floor drainage slope (or hole) that will SAFELY DISPOSE of the FULL
FLOW of any water that may leak out should the machine malfunction.
It is therefore the OWNER'S RESPONSIBILITY to make sure this machine is installed in an area with
a drain hole (or slope) that will prevent any possibility of water damage to floor coverings or property.
● Permissible water temperature : Max 70°C(160°F)
● Permissible water pressure : Max 80psi (550kpa, 8kg/cm2), Min 4psi (30kpa, 0.3kg/cm2)
● If water temperature & pressure is greater than above, it may cause damage to the machine. If you
have uncontrolled water temperature & pressure you should fit a temperature & pressure relief valve
to ensure that water temperature & water pressure remains within the safe limits. Consult a plumber
or electrician if you are unable to adjust water temperature and pressure.
● Do not over tighten the coupling nuts with a tool. Inlets are plastic : Do not strip or crossthread.
Install the washing machine on a flat and firm surface.
● Install the washing machine on a level and firm surface.
● Keep the washing machine more than 10cm from the wall to prevent vibration noise during spinning.
● The base opening must not be obstructed by carpeting when the washing
machine is installed on a carpeted floor.
● Wooden floors may need reinforcing to prevent the normal vibration which
occurs with an unbalanced load.
● If the washer is installed on a uneven,weak or tilted floor causing excessive vibration,
” error can happen to it.
spin failure or
It must be placed on a firm and level floor to prevent spin failure.
● If the appliance is supplied from a cord extension set or electrical portable outlet
device the core extension set or electrical portable outlet device should be
positioned so it is not subject to splashing or ingress of moisture.
Level the washing machine
❏ Check the level of the washing machine using a
spirit level on the side of the washing cabinet
❏ You can check the level also by visually lining up the
washer with the fills, adjacent walls or cabinets.
❏ You can level the washer using the A.L spindle fitted to the cabinet.
● Screw the A.L SPINDLE legs up or down as required.
● Additional height adjustment plates are provided in the accessory bag. These fit under A.L SPINDLE
if required to allow for greater adjustment of the legs.
● When washing machine does not even out, turn A.L SPINDLE
right or left to be level.
● Should the height adjustment exceed the maximum
allowed by the A.L SPINDLE, place height
adjustment plats provided under
the legs as shown in the
1 plate used 2 plates used 3 plates used 4 plates used
Before Starting to Wash
reparation Before Washing
Care Labels
* Look for a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
To get the best results, different fabrics need to be washed in different ways.
Separate clothes according to the type and amount of soil.
• SOIL (Heavy, Normal, Light)
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
Lint Producers
Lint Collectors
Terry cloth, Chenille, Towels, Nappies
Synthetics, Corduroy, Permanent Press, Socks
Check before Loading
• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue in pockets.
Pretreatment on stains or heavy soil
• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
• Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page13)
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size
accordingly. Loosely load clothes no higher than the top row of holes in the
washer tub. To add items after washer has started, press Start button and
submerge additional items. Close the lid and press Start button again to restart.
Fire Hazard
Never place items in the washer that are
dampened with gasoline or other flammable
No washer can completely remove oil.
Do not dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent
tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
Before Starting to Wash
se of Water, Detergent, Bleach and Softener
Using Water
• This machine detects the quantity of laundry automatically, then sets the WATER
LEVEL and proper amount of Detergent.
• When you select a wash program, the WATER LEVEL and amount of Detergent
(to be used) will be shown on the control panel.
• The following table shows the amount of water.
• When the WATER LEVEL is automatically detected, it may differ depending on the
quantity of laundry even though the same WATER LEVEL is indicated on the control panel.
• The amount of a cup in the diagram is about 40g for concentrated Detergent.
Water Temperature
• The machine sets the appropriate temperature automatically according to the wash program .
• You can change the Water Temperature by pressing the WATER TEMP. button. (refer to page 14)
• The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.
We recommend temperatures of:
- HOT 49~60°C…(120-140˚F)
White items, diapers, underclothing and heavily soiled, colorfast items.
- WARM 29~40°C…(85-105˚F)
Most items
- COLD* 18~24°C…(65-75˚F)
Only very bright colors with light soil.
• When washing in COLD water additional steps may be needed:
- Adjust Detergent amount and pre-dissolve Detergent in WARM water
- Pretreat spots and stains
- Soak heavily soiled items
- Use appropriate bleach
* Temperature below 18°C…(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29°C…(80-85˚F).
If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown
or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be
necessary for severe cases.
Using Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or
granulated soap powders should not be used in your washing machine. When washing woolens
remember to use Detergent suitable for washing woolens.
How much Detergent
When you select a wash program the WATER LEVEL and the amount of Detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated Detergent.
The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work
cloches may need more Detergent, while bath towels usually need less.).
For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.
Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of
foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough
Detergent has been used; soil and lint can settle back on the clothes or the washing machine.
If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
Adding the Detergent
Open the Detergent dispenser and deposit the appropriate
Powder Detergent Box
amount of Detergent
Dispensador de( detergente
en polvo.
where you deposit the Detergent
Powder Detergent dispenser.
Some Detergents MUST be fully dissolved before
adding to your machine to get the best wash results.
It is recommended to dissolve the measured amount of detergent
in 1 litre of water before adding to the machine
Check the instructions on the Detergent packet.
If you use powdered Detergent it is essential that the required amount be fully dissolved in very HOT water
before being added to WARM or HOT water for the actual wash.
Pre-dissolving Detergent in WARM water when washing in COLD water can improve its performance.
Using Liquid Bleach
• Check clothing care label for special instructions and separate the
laundry to be bleached
• Dilute liquid chlorine bleach.
• Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
• Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
Do not pour powdered bleach into bleach dispenser.
Bleach dispenser
Before Starting to Wash
Using Detergent
Before Starting to Wash
se of Water, Detergent, Bleach and Softener
Using Fabric Softener
• Dilute fabric softener with water.
Undiluted fabric softener may result in spots that look like oil
• Measure and add the recommended amount of fabric softener
into the compartment marked with this symbol( ).
Follow manufacturer’s direction.
Softener dispenser (
Fabric softener is automatically dispensed in the final rinse
with indication beep.
If you want EXTRA RINSE, you must add fabric
softener manually when indication beep rings in the final
rinse. This maximize the fabric softener function.
• Do not overfill. The dispenser hold max 35mL.
Never add more than 35mL.
Overfilling can cause early dispensing of the fabric softener
which could result in stained clothes. A cup with a pouring spout will help you avoid spilling.
• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes its
effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be manually
put during the time when the washer beeps several times before the final rinse. This function informing
correct time to dispense manually is optionally applied to some models. Please keep it in mind that fabric
softener has to be diluted with water before dispensed and never poured directly on clothes.
■ Do not mix with Detergent or bleach.
■ Never pour fabric softener directly on clothes. It may stain them.
■ Do not stop the washer during the first spin for timely dispensing.
■ Option washing is not designed to be used with fabric softener dispenser.
■ Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
■ To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep stain removal products in their original labeled containers and out of children’s reach.
• Thoroughly wash any utensil used.
• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents
or other flammable or explosive substances because they give off vapors that could ignite or explode.
• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from
granular Detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
Follow fabric care label
• Check for colorfastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.
Stain Removal
Adhesive tape, chewing gum,
rubber cement
Baby formula, dairy products, egg
Beverages (coffee, tea, soda, juice,
alcoholic beverages)
Candle wax, crayon
Collar or cuff soil, cosmetics
Dye transfer on white fabric
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Mildew, scorch
Mustard, tomato
Nail polish
Paint, varnish
Rust, brown or yellow
Shoe polish
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using COLD water and bleach safe for fabric.
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
safe for fabric.
Before Starting to Wash
pecial Guide for Stain Removal
The pulsator rotates for
8 seconds to detect the
laundry load.
and the amount of
Detergent to be used
will be shown and
water will be supplied.
Water will be
supplied for 2
minutes after the
start of the wash to
supplement the
water the laundry
has absorbed.
Caution & Note
When the wash
program ends, the
buzzer will ring
for 10 seconds
before the Power
goes off
If water is already in the tub, or putting
wet laundry into the tub before starting
will increase the WATER LEVEL.
With lightweight bulky loads, WATER
LEVEL can be set low.
Changes to Water Temperature
(HOT/COLD) and wash level are
possible during operation.
(refer to page 14)
When setting the WATER LEVEL
manually, do not set to Medium to
prevent damage to laundry.
Washing with HOT water may damage
the laundry .
Ensure that the load is under 2kg.
In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing
may still contain some water.
This is normal.
If WOOL wash is selected, GENTLE SPIN
will be set automatically.
·Before starting to wash, make sure that
the laundry is washable.
Washing with HOT water may damage
the laundry.
Washing Programs
Close the lid
Washing Programs
Use this program to wash quietly in SILENT especially during late night and dawn.
Press the AUTO OFF (POWER) button to turn power on.
Press the PROGRAM button to select SILENT program.
Add the laundry into the washing tub.
Press the START/PAUSE button.
Add the Detergent and close the lid.
• SILENT program takes longer washing time than FUZZY program.
• To reduce noise in spinning, spin rpm is lower than normal spinning rpm.
So the laundry has more moisture than normal.
Normal, Water level L is the one to be used for a normally soiled load
Program setting with “Normal + Water Level “L” + Warm”
Option for test in confirmity with AS/NZS2040.2 & AS/NZS6400
1) Water Level
Additional Function Program
DELAY START (RESERVATION) Wash is used to delay the finishing time of the
operation. The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time , not the start time.
Press the POWER button to turn power on.
Press the PROGRAM button to select the washing program.
Press the DELAY START (RESERVATION) button to set the time when the
delayed washing is to be completed.
Select the program for laundry on the Control panel.
This program will not work in WOOL and DELICATE
How to set the delay time.
Example : It’s 7 a.m. now. If you’d like your wash to finish at 9
p.m. set the time as in the figure below.
When you push the button the reservation time changes
3 u 4 u 5 u ...12 u 14 u 16 u... u 48 u 3 repeatedly.
Add the Detergent.
Add the laundry and press the START/PAUSE button.
Close the lid.
Water will be supplied for 2 minutes after the start of the
wash to supplement the water the laundry has absorbed.
The washing will be finished according to the delayed time.
The appropriate quantity of Detergent marked next to the
When the lid is open the machine will not operate, and an
alarm signal will remind you to close the lid
When you press the START/PAUSE button the light will
If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.
To select washing program, spinning time, WATER LEVEL or HOT/COLD manually, press the DELAY
START (RESERVATION) button and select the desired option. Then press the START/PAUSE button.
When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the
spinning program . (The laundry will be wrinkled if left for a long time after spinning.)
When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set
Press the AUTO OFF (POWER) button to turn power on.
Wash , Wash+Rinse , Rinse , Rinse+Spin , Spin only options
Press the PROCESS button until above Option Washing
light is on. (refer to page 15)
When you want to only drain, wait until the water in the
washing tub drains completely and then, turn off the
Press the WATER LEVEL button, to control the WATER LEVEL according
to the amount of laundry. If you do not choose anything, it is set the Large
WATER LEVEL automatically.
(refer to page 14)
Add the laundry into the washing tub.
Press the START/PAUSE button.
Add the Detergent and close the lid.
• When a Wash, Wash/Rinse or Rinse only option is selected, the water will not be drained off after the
wash is completed.
• If you do not specify the WATER LEVEL, then Large will be automatically selected.
• If only Rinse is selected, the process will start from Water Supply.
Additional Function Program
ption Washing
Disconnect the power cord.
Pull out the filter from the
inlet valve.
Use a tooth brush to get rid of
dirt. Replace it.
Insert it into the original
Pull out the waste thread
collection net from the tub
in the direction of the arrow
Turn inside out to get
rid of filth.
● Wipe stains from the cabinet and the control panel
with a soft cloth.
● Do not pour water directly on the cabinet.
● Do not wipe the cabinet with benzine, thinner,
cleanser, alkaline detergent or wax.
● Do not rub the cabinet with a scrubbing brush.
● When you use a chemical dustcloth, follow the
• If an abnormal symbol appears in the display window, check the following before asking for service.
• Request for the service center or agent in the case of failure or damage except for the following.
• This appliance is fitted with a safety function that automatically stops the operation of the washing
machine when it is exposed to heavy disturbance on the mains.
Water Supply
Error Message
Check up
. Is the water tap shut off?
. Is the water supply cut off ?
. Is the tap or water supply hose frozen ?
. Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
. Is the Hot hose connected to cold?
. Is the Cold hose connected to hot?
Drainage Failure
. Is the drain hose positioned correctly?
. Is the drain hose bent or placed too high?
. Is the internal part of the hose or drain pump
(only pump model) clogged with impurities?
. Check if power has gone off.
Spin Failure
Door(Lid) Open
Internal sensing
Power failure
Overflow failure
. Is the laundry evenly balanced?
. Is the washing machine placed on a flat surface?
. Is the lid closed?
. Please call your nearest LG Electronics service center
for help.
Download PDF