LG | WF-T902 | LG WF-T902 Owner’s Manual

Washing
Machine
OWNER'S MANUAL
MODEL
:
WF-T854A, T902A
Please read this manual
washing
carefully before operating
machine and retain it for future reference.
your
FEATURES
.........................................................................................
3
IMPORTANT SAFETY PRECAUTION................................................ 4
MACHINE PARTS............................................................................... 6
INSTALLATION
...................................................................................
7
AUTOMATIC AND MANUAL PROGRAMMING.................................10
NORMAL, JEAN WASH PROGRAM
.................................................12
SPEEDY, DELICATE WASH PROGRAM
.........................................
WOOL, SOAK, FAVOURITE WASH PROGRAM
DELAY START WASHING PROGRAM
SELECTABLE WASHING METHODS
WASHING PROCEDURE
.............................
............................................
..............................................
.................................................................
WATER LEVEL AND AMOUNT OF DETERGENT
...........................
14
16
18
20
22
23
HOW TO USE THE BLEACH AND THE SOFTNER......................... 24
SELECTING EACH BUTTON
MAINTENANCE
...........................................................
................................................................................
25
26
TROUBLE-SHOOTING GUIDE......................................................... 28
SPECIFICATIONS
2
P/No.3828EA3006Q
............................................................................
30
FEATURES
CAUTION
"Turbo Drum" washer doesn't operate while the lid is open. If the lid is
during the wash, rinse and spin cycles, the operation stops for safety.
opened
Fuzzy logic control
A load
sensor
&
micro processor in the controller detect laundry load and set
conditions such as water level, wash time etc.
a
optimum washing
The most advanced
electronic control
the best
technology
in
START
system provides
SENSING
SETTING
Laundry Sensor
Optimum
Washing
Water Level Sensor
Condition
WASHING
AUTO
POWER
OFF
washing performance.
Turbo drum
washing
The
"punch + 3" washing wings and the washing tub turn in
opposite directions. This makes the water current flow in two
directions which improves washing efficiency.
The wash
performance is also improved by the water which
continually cascades into the wash bowl from small
waterfalls in the washing tub.
Innovated
washing wings
Three small
washing wings generate strong and
sharp washing currents to clean laundry uniformly.
Adjusted vertical movement and rotating direction
of the washing punch reduces laundry entanglement
and improves washing power.
3
Step washing
3
step washing produces the best washing performance
with low
tangling.
Rubbing
Device for
Rubbing
Shaking
and
and
Shaking
Disentangling
removing naps
Lint filter catches naps and thread generated
washing to make the laundry cleaner.
during
3
P/No.3828EA3006Q
is not intended for use by
or infirm persons without
Never touch the clothes in the bowl during
operation or until the while bowl stops
The
rotating.
supervision.
Young children should be supervised
to ensure that they do not play with the
appliance.
Even when
around
rotating slowly, the clothes may wrap
your fingers, which is dangerous.
Don't put hand(s)
operation.
Rotating parts
may
under the washer
injure
your
during
hand(s).
young children
Don't put kerosene, gasoline, benzine,
thinner or clothes containing these
chemicals into the washer.
An
Keep washer away from fire(a heater,
burning cigarette, etc.).
The washer may be deformed
out.
or a
fire may break
appliance
result.
explosion might
After
washing
Close the water
tap.
Turn the POWER button "OFF" at the wall power
outlet, if you will not be using the machine for a
long period
To
of time.
prevent
water
leakage, fire,
electric
etc.
OFF
OFF
OFF
4
P/No.3828EA3006Q
shocks,
Don't rest jean objects
pressure to the lid.
Don't bend the lid
forcibly,
on or
as
Don't press the switches and/or the
with a sharp object, the pencil.
apply
it may break.
Switch and/or
panel damage
or a
panel
malfunction may
result.
Don't install the washer where it would be
to direct sunlight.
exposed
Plastic
parts and the painted cabinet may be
deformed and/or fade.
Don't
If
spin-dry
starched clothes.
only
half the normal amount of
Otherwise, starch adhering
Plastic
hot water.
parts of the washer may be deformed
or
damaged.
Don't
spined by mistake, operate the washer without
load with
Don't use excessively
(above 70°C)
use
The rubber
strong alkaline detergents.
parts may be damaged.
detergent.
to the bowl may soil
other clothes.
5
P/No.3828EA3006Q
MACHINE PARTS
START/PAUSE
HOT WATER SUPPLY
BUTTON
HOSE
Use to start
washing
porarily.
or
stop the
machine tem-
COLD WATER SUPPLY
HOSE
Make
FUNCTION SELECTOR
LIGHT
HEAVY
Powder
for
detergent box
delayed washing/
sure
the water
does not leak.
SML
FAVOURITE
STAN
LEVEL
SOAK
WATER
XL
COLD
HOT
WASH
MN
LEVEL
WATER
TEMP.
TIME
RINSE
CATE
DELAY/
IMELEFT
SPIN
DELAY
NOINLET
DOOROPEN
WOOL
NORMAL
MIN
SPEEDY
PRO-
GRAM
AUTO
START
OFF
PAUSE
JEAN
NODRAIN
softener box
LINT FILTER
Clean
regularly to stop
linting
on
the clothes
load.
INLET HOLE FOR
BLEACH
DRAIN HOSE
Check if the drain hose
is located in the
WASHING WINGS
tub before
Vertical movement of
washing
washing punch can be
operated when a sufficient
amount of laundry is
deposited.
If the
supply cord is
damaged, it must be
replaced by the manufacture
water may increase
of
machine.
POWER PLUG
Set the proper water level,
an excessive amount of
entanglement
laundry
operating the
or
laundry.
its service
agents
similarly qualified
LEVELLING LEGS
Use to level the
washing
machine for correct balance
&
BASE
spin operation.
Accessories
Height adjustment
plate
Inlet hose
1 Each for cold and
2 Pieces
6
P/No.3828EA3006Q
or
person
in order to avoid a hazard.
hot water
Drain hose
INSTALLATION
How to install the drain hose
1. Fit the machine end of the drain hose to the outlet of the drain
pump and
Holder
tighten
the
clamp.
Within 50mm
Push
Drain Hose
Hose
Holes
Guide
2. Put the other end of the drain hose
For Holder
3. Fit the
0.9~
plastic
over
the
standpipe or wash tub.
holder into either holes for the holder at the
rear
of
the machine. The holder is
1m
according to location
keeps firmly the drain
down
as
possible to fit at either direction
of the standpipe. Make sure that the holder
hose
shown in the
so
that the drain hose should not fall
fig.
Holes for the Holder
NOTE:
To
prevent syphoning, the drain hose should
more
The
than 50
mm
not extend
from the end of the hose
discharge height
should be
guide.
approximately 0.9~1m
from the floor.
Flooding drainage
Your machine
requires
a
floor
drainage slope (or hole)
that will SAFELY DISPOSE of the FULL FLOW of
any water that may leak out the machine malfunction.
It is therefore the OWNER'S RESPONSIBILITY to make sure this machine is installed in an area with a
drain hole
(or slope)
that will
prevent any possibility of
water
Connect inlet hose
Check that
sealing washers
are
property.
SEALING
WASHER
washing machine;
TWIST
the
Either hose
TAP
END
INLET
VALVE
be attached to hot inlet valve and tap.
taps and check for leaks. Tighten the coupling nuts firmly if there
is any leakage. If water pressure is strong, close the water tap completely
on
or
TAP
SEALING
WASHER
firmly seated.
coupling nuts securely by hand. (Fig. 1)
Attach the straight end of the hose to the tap.
Tighten the coupling nuts securely by hand. (Fig. 2)
Turn
coverings
MACHINE END
Attach the curved end of the hose to the inlet valve of the
Tighten
to floor
damage
can
INLET
HOSE
the
then open it
(Fig. 1)
slightly.
Do not install the washer where it is
CAUTION
directly exposed to sunlight, wind,
(Fig. 2)
rain etc.
Plug the
power cord of this washer into a properly installed standard power
Permissible water temperature : Max 70°C(160°F)
point that is
switched & earthed.
Permissible water pressure : Max 116psi (800kpa, 8kg/cm2), Min 4psi (30kpa, 0.3kg/cm2)
If water temperature & pressure is greater than above, it may cause damage to the machine. If you have
uncontrolled water temperature & pressure you should fit a temperature & pressure relief valve to ensure that
water
temperature
& water pressure remains within the safe limits. Consult
Do
adjust water temperature and pressure.
not over tighten the coupling nuts with a tool. Inlets
a
plumber or electrician
if you
are
unable to
are
plastic
:
Do not
strip
or
crossthread.
7
P/No.3828EA3006Q
INSTALLATION
Improper
1. The
installation of the washer may
ventilating openings
machine is installed
2. Install the
on a
in the base
carpeted
machine
washing
on a
cause
area
noise and
malfunctioning.
must not be obstructed
level and
1Installation
firm surface.
washing
area
Install the washer
How to
when the
by carpeting
floor.
on
flat and firm surface.
adjust level
Horizontal
4
setting
Lift up the front of the washer and
the level indicator to the center by
adjustable legs
clockwise
or
adjust the drop of
turning the
using the adjusting plate.
Adjustable leg
Horizontal
Location of
setting
Cause
How to
adjust
When the front is lower.
Adjust the front adjusting plate
or adjust the adjustable legs.
with the
adjustable legs(2),
When the
Adjust the rear adjusting plate
or adjust the supporting plate.
with the
adjustable legs(2),
drop
rear
is lower.
When the left is lower
When the
(Example)
To
move
plate,
the
P/No.3828EA3006Q
is lower.
Adjust
or
drop of the level indicator by 15
adjustable legs 2-3 times.
and turn the
8
right
Adjust the left part of
the supporting plate.
the
the front and
the right part of the
supporting plate.
mm:
Use two
rear
front and
adjusting plates
and
adjusting plates
rear
a
10
or
adjusting plates
mm
supporting
Checking
2
Open
lid, and check if the washer is correctly
by looking down from the top.
the
drop
Confirming
5
3
the
leveled
Adjust
level
Checking slope
Check if installation surface is tilted.
(Try to shake the
firmly installed.)
of the level indicator to the red circle.
level
6
washer and check if the washer is
Distance between drain hose and the wall
More than 10cm
More than 2cm
More than 2cm
Place the washer to
level
as
confirm
in
2.
figure
the level.)
original position and confirm
(Try to shake the washer and
the
Distance between drain hose and the wall should be
more
than 10cm, and the distance between the other
more than 2 cm.
sides and the wall should be
Check the location of the level in the front of washer.
CAUTION
If the
core
to
How to
Use the
legs
use
the
appliance
is
extension set
splashing
or
supplied
or
from
electrical
ingress
a
cord extension set
portable
or
electrical
outlet device should be
portable outlet device the
positioned so it is not subject
of moisture.
adjusting plates
adjusting plates
to level the washer when the
adjustable
cannot cover the gap.
9
P/No.3828EA3006Q
AUTOMATIC AND MANUAL PROGRAMMING
Fully automatic control
The
program is used for average
Fuzzy
washing.
day
to
Close the lid and press START/PAUSE button.
lights will scroll up and down while
day
The water level
Press POWER ON button.
the washer is
Load clothes.
for your clothes load.
Add
detergent,
bleach and conditioner
as
working
out the
optimum
water level
desired.
Preparation before wash
STAIN LEVEL
SELECT
FAVOURITE SELECT
Sort your
washing
Each load of
washing
washing
into
separate wash loads
should contain
conditions. For
which needs the
clothing
Pressing the
same
you should not wash delicate
work clothes.
example,
clothes with very dirty
Some fabrics are lint collectors and
from other
fabrics, which
are
lint
pick up lint, dirt and colour
producers. Some examples are
can
listed below.
LINT PRODUCERS
Corduroy
Synthetics
Towels
Permanent press fabrics
Chenille / Candlewick
Make
sure
By pressing
[HEAVY▶
button
lows you to store your
favourite wash condi-
LIGHT▶MEDIUM
tions in the NORMAL
mode
memory and
than recall it for use at
Available
cycle
a
LINT COLLECTORS
Default is MEDIUM.
FA-
VOURITE button al-
repeats.
during
washing.
later time.
Except for WOOL
and
DELICATE program.
Nappies
that you wash lint collectors
separately from
lint
producers.
SOAK
STAIN
LEVEL
LIGHT
HEAVY
WATER
LEVEL
SM
LX L
COLD
FAVOURITE
Check if
laundry
is washable in
Be
to remove
sure
keys, pins
laundry.
water.
as
things
such
Used to select proper
temperature of
water
oily dyed laundry
separately.
or
WATER
TEMP.
and coins from the
HOW TO
SELECT TEMP.
Wash
HOT
Shake loose dirt off before
washing.
washing water.
[WARM(Hot and cold
light turn on) HOT
COLD
WARM]
mode
repeats.
HOW TO USE
DELAYED WASHING
Use this function for
delayed washing.
Use it to set the delay
time.
By pressing the button,
itcycles[3 4 5
... 11 12 14
16 ... 46 48 3]
hours. (Up to 48 hours
can be delayed).
To cancel delay time,
turn the power switch off.
Wash
fluffy laundry by turning
it inside out.
10
P/No.3828EA3006Q
Wash delicate
wrapping
Except for WOOL
and
DELICATE program.
clothes,
them in
a
nylon
net.
Manual control
Other programmes are selected
Press POWER ON button.
as
follows.
Load clothes.
Add
detergent,
bleach and conditioner
as
desired.
Select
temperature, level, process, program and
Close the lid and press START/PAUSE button.
In
operation, the following
displayed.
Abnormal water supply : NO INLET. lamp blinks.
Abnormal drainage : NO DRAIN. lamp blinks.
Abnormal spin :
UE displayed.
Abnormal water level sensing :
PE
displayed.
Abnormal lid open : DOOR OPEN. lamp blinks.
case
as
described below.
HOW TO SELECT A
WASHING PROGRAM
DISPLAY ABNORMAL
OPERATION
of abnormal
indications
options
are
POWER
Use it to select
Use it turn
on
By pressing
[NORMAL
the button
[On Off]
DELICATE
washing programs.
the button, it cycles
SPEEDY
JEAN
WOOL
By pressing
repeated.
are
NORMAL]
and off.
Electric power automatically
turns off in 10sec, after the
washing cycle
finishes with "boo-"
sound.
Electric power
automatically
turns off after 10min.in 'Pause'
condition
NO INLET
FOR MANUAL WASH,
RINSE AND SPIN
DOOR OPEN
DELICATE
WASH
MIN
RINSE
AUTO OFF
WOOL
DELAY / TIME LEFT
Wash:
START
PROGRAM
NORMAL
TIME
Use it to change washing time.
By pressing the button [21min
PAUSE
SPEEDY
SPIN
DELAY
5min
SOAK 21min
JEAN
MIN
SOAK 10min
OFF
SOAK
SOAK 15min
5min
10min
NO DRAIN
15min]
SOAK is used to
hardened dirt
remove
old
effectively.
Soak time is about 60minutes (You
cannot choose in WOOL program.)
or
Rinse:
HOW TO ADJUST
START AND TEMPORARY PAUSE
THE WATER LEVEL
the button, it cycles [LARGE
LARGE EX-LARGE
EX-LARGE
SMALL
SMALL MEDIUM
MEDIUM
MEDIUM LARGE
LARGE]
At FUZZY and JEAN program, water
level is selected automatically based on
the amount of laundry.
Water level is set to LARGE for WOOL
and DELICATE program.
Water level is set to MEDIUM for SPEEDY program.
Water level can be adjusted even when
the washer is in operation.
For appropriate quantity of detergent
follow the detergent manufacturer's
instruction
By pressing
?
?
Use it to start
or
By pressing the
are repeated.
pause.
button [Start▶Pause]
?
:
3
step works
more
at
large
CHILD LOCK
Used to lock
tons to
or
Use it to change the frequency or rinse.
By pressing the button.
[rinse1 rinse2 rinse3 rinse4
OFF
rinse 1] are repeated.
When you select rinse only, the
operation starts with water supply.
Spin:
Use it to change the spinning time.
By pressing the button, [5min 7min
OFF
1min
3min
5min].
unlock the control but-
prevent all the setting from being
changed by a child
For locking, push both buttons simultaneously and for unlocking, push them
once more during the washing process.
and medium water level of NORMAL and JEAN progream.
11
P/No.3828EA3006Q
Use the Normal program for normal
Jeans, overalls etc.
All conditions such
automatically
as
water
selected
dirty laundry
and Jean program for
level, wash time, rinse and spin time
by microcomputer.
are
All you have to do is press the
START/PAUSE button.
Check to
see
if
everything
Preset program
Spray
rinse
gives
is
ready.
:
rinse
(Normal course), Deep2 rinse(Jean course).
Deep1
(cold or hot water can be set optionally
following table 1.)
+
Warm wash water
...
see
the
Table 1. WASH WATER TEMPERATURE GUIDE
USED FOR
WATER TEMPERATURE
White and colorfast cottons, linens with jean
Permanent press & synthetics with heavy or
Hot
Dark
Warm
or
or
normal soil.
oily
non-color fast fabrics. White & colored
soil.
synthetics.
Permanent press with normal or light soil.
Wool is only selected with warm.
Lightly
Cold
soiled fabrics.
Table 2. FILL TEMPERATURE OF EACH CYCLE FOR PROGRAM
For each program, the
washing
machine
automatically
selects
a
suitable fill water
temperature.
FILL TEMPERATURE
PROGRAM
APPENDIX EXPLANATION
WASH
Nomal, Jean,
Speedy, Soak,
Favourite
temperature
NOTE
Fill
HOT
WARM
:
WARM
temperature for wash
can
be
change
washing style.
COLD
Fill cold for rinse is not able to
COLD
Delicate, Wool
A wash
RINSE
energy
to be selected is illuminated
during
the
because of
change
saving.
Fill temperature is not able to
transformation.
WARM
a
complete cycle
on
to
the control
or
Manually adjust proper water level
Bulky and light laundry may cause
water level lower than usual. In this case,
a
laundry is wet, water
operating the washer.
change
If either the inner-tub contains water
before
the to suit
protect laundry
panel.
levels may become
higher.
manually adjust the
water level.
For
laundry that may easily be discolored, do not use [SOAKING] washing.
supply may be resumed about 2 minutes after starting the wash. It is an automatic water
level adjustment function.
When using natural detergent or liquid detergent, deposit proper amount of detergent based on
[instruction for detergent].
Water
12
P/No.3828EA3006Q
the
1
Press the POWER button.
2
Select the desired program.
in the tub.
3
Put
6
Close the lid.
laundry
NO INLET
AUTO OFF
DOOR OPEN
DELICATE
WOOL
PROGRAM
START
PAUSE
SPEEDY
NO DRA
Press program button to select
either
[NORMAL]
or
[JEAN].
Press the START/PAUSE
4 button.
5
Put
detergent
bowl
as
in the wash
indicated
on
the
display or instruction of
detergent manufacturer.
PROGRAM
START
SM
LXL
PAUSE
Electric power is
out after
washing
automatically
program
finishes.
13
P/No.3828EA3006Q
SPEEDY WASH PROGRAM
Use this program for
washing slightly
soiled
laundry.
the power button
1Press
This program is economical because of its short
washing time.
of laundry.
Adjust water quantity according to the amount
Preset program gives: -10 minutes wash
-Spray rinse + Deep1 rinse
-3 minutes spin
AUTO OFF
-Medium water level
-Warm water
(Cold
or
hot water
can
be set
optionally)
DELICATE WASH PROGRAM
Use this program for
Microcomputer
Place
detergent
Preset program
washing
controls the
delicate
strength
laundry
such
as
lingerie,
blouses etc.
1Press
of circulation.
in
detergent dispenser.
gives: -10 minutes wash (Gentle wash)
-Deep 2 rinse
-1 minutes spin
-Large water level
the power button
AUTO OFF
-Warm water
NOTE
:
When you wish to
change washing cycles,
select them
manually.
4Press
the START/PAUSE
button.
PROGRAM
14
P/No.3828EA3006Q
START
PAUSE
2
PROGRAM
[CYCLE] selector
3
NO INLET
DOOR OPEN
DELICATE
WOOL
PROGRAM
NORMAL
START
PAUSE
JEAN
After
NO DRA
closing
the lid press the START/PAUSE
button.
Set the program selector to
2
Put
laundry
[SPEEDY] by pressing
Deposit detergent based on the indicated
Power goes off automatically after wash
it.
amount.
finishes.
in the tub.
3
PROGRAM
[CYCLE] selector
NO INLET
DOOR OPEN
WOOL
PROGRAM
NORMAL
START
PAUSE
SPEEDY
JEAN
NO DRA
Set the program selector to
it.
[DELICATE] by
pressing
Put
detergent
5 display
or
SM
in the wash bowl
instruction of
as
detergent
indicated
on
the
manufacturer.
6
Close the lid.
LX L
Electric power is
washing
automatically
out after
program finishes.
15
P/No.3828EA3006Q
WOOL WASH PROGRAM
Use this program for
washing
Do not wash woollens with
a
washable
woollens, less than 2.0kg.
dry cleaning
Do not set water level to medium
or
1Press
label attached.
below.
AUTO OFF
Wash clothes with buttons and accessories inside out.
Preset program
gives:
the power button
-5 minutes wash
-Deep
2 rinse
-1 minutes
-Large
spin
water level
-Warm water
NOTE
When you wish to
:
change washing cycles,
select them
manually.
SOAK WASH PROGRAM
Use this program for
washing heavily soiled laundry after soaking.
provides the best washing effect.
this program for washing laundry that may discolor.
This program
Do not
use
Preset program
gives:
-60minute
-Deep
1Press
the power button
AUTO OFF
soaking
1 rinse
-Warm water
(Cold
or
hot water
can
be set
optionally)
FAVOURITE WASH PROGRAM
Pressing
the favourite button allows you to store your favourite wash
cycle memory and then recall it for use at a
conditions in the normal
later time.
1Press
the power button
AUTO OFF
16
P/No.3828EA3006Q
2
PROGRAM
[CYCLE] selector
NO INLET
3
Deposit detergent
4
DOOR OPEN
DELICATE
PROGRAM
NORMAL
START
PAUSE
SPEEDY
JEAN
NO DRA
Set the program selector to
it.
[WOOL] by pressing
Use proper kind of detergent
to the type of laundry.
according
Press the START/PAUSE
button after
closing
the lid.
Power goes off automatically
after wash finishes.
2
[WATER LEVEL] selector
3
PROGRAM
[CYCLE] selector
4
SOAK
WASH
MIN
RINSE
TIME
WATER
LEVEL
SM
SPIN
LX L
MIN
Set the program selector to
[SOAK] by pressing it.
After
the lid press the
START/PAUSE button.
closing
Power goes off automatically
after wash finishes.
2
Select the
[FAVOURITE]
program.
3
Select your favourite wash
conditions.
4
Press the START/PAUSE button
to store & start your favourite
Press the WATER TEMP. button to
select wash water temperature.
wash
Press the WATER LEVEL button to
after wash.
cycle.
Power turns off
automatically
select water level.
FAVOURITE
Press the STAIN LEVEL to select
HEAVY
or
LIGHT wash
Press the WASH
option.
button, the RINSE
button & the SPIN button to select
wash time, rinse times & spin time
respectively
you want to store.
Push the FAVOURITE button
(FAVOURITE cycle setting)
To recall your favourite cycle.
1. Press POWER on.
2. Select the favourite cycle by
pressign the PROGRAM.
3. Push the FAVOURITE button
(FAVOURITE cycle settng.)
4. Press the START/PAUSE button.
Then the wash
cycle
starts.
17
P/No.3828EA3006Q
DELAY START WASHING PROGRAM
This
can
be used
conveniently for every washing program.(except for DELICATE
delayed washing, switch the power off and start again.
and WOOL
program.)
When you want to cancel
1
Press the power button.
2
Select
a
program.
3
Set the time.
DELAY / TIME LEFT
NO INLET
DOOR OPEN
DELICATE
AUTO OFF
WOOL
START
PROGRAM
PAUSE
DELAY
NO DRA
Press the DELAY START button
to set the number of hours before
you want the
washing
to be
completed.
How to set the
Example
It's 7
:
delay
a.m. now.
If
time
you'd
When you push the delay start
you want the wash to be
like your wash to finish at 9 p.m. set the time
in the
figure
below.
DELAY / TIME LEFT
completed [3 4 5...
12 14 16... 48 3]
How to
as
button, the delay time repeatedly changes the number of hours before
14hours:7a.m.
~9p.m.
put the detergent into the detergent box
For
powder detergent
detergent box.
Pull put the box and put the detergent then
close the box again.
Pour it into the exclusive
2
For
Put the
at the rate of 1:1.
Put the
agent
3
1
Dry
the moisture in and out of the box before
the
detergent.(moisture
18
P/No.3828EA3006Q
liquid detergent
detergent after diluting it with
may harden the
inserting
detergent)
bleaching
here
the water
4
Insert laundry and press the
START/PAUSE button.
Deposit detergent
5 powder detergent
in the
6
box.
Close lid and press
START/PAUSE button two
times
START
PROGRAM
Insert
again.
PAUSE
Pull the powder detergent box forward and
deposit displayed amount of detergent on
control panel (or detergent usage of brand)
Then, push back the box.
During depositing powder detergent, you will
and press
START/PAUSE button. The
laundry
washer
senses
laundry
and
the amount of
displays
the water
hear
level.
an
alarm sound. It is not
message, but
lid.
just
If the lid is not
closed, the
machine cannot start
It
If the lid is
an error
washing
reminds you to close the
spinning.
generates the alarm sound.
opened, delayed
proceed.
cannot
CAUTION
Make
sure
deposit detergent in the powder detergent box.
detergent with the laundry for a long time, the laundry
to
If you leave
When the lid is
In
case
opened, delayed washing
of power
Depending
or
failure,
water
set
again
cannot
from the
After
setting delay time,
water
temperature and
you
can
detergent
change
partially
discolored.
proceed.
beginning.
supply conditions, washing
Remove any water from the powder
Moisture may harden the detergent.
may become
may be unable to be
box before
completed by
the
preset time.
depositing detergent.
the program, wash
time, number of rinses, spin time,
water level.
NOTE:
How to wash when you go out
When you cannot take the laundry out immediately after
and rinse only(In this case, do not select spin to prevent
washing is completed,
wrinkles).
you should select wash
19
P/No.3828EA3006Q
SELECTABLE WASHING METHODS
Use it to select the desired
cycle
Press the
power switch.
among
washing,
rinse and
WASHONLY?
?
?
spin,
to
or
When wash
repeat
liquid
one
of them after
Adjust
RINSE
the water level
according
If the water level is not
SPIN
is
washing
time.
completed.
is to be used twice.
Press the WASH button to select the
WASH
washing
to the amount of
laundry.
selected, it is automatically
set to
[LARGE].
WASH&RINSE?
?
?
When it is not desirable to
spin
clothes in order to avoid wrinkles.
Press the WASH button to select the
WASH
washing
time.
Press the RINSE button to select the number of rinses.
RINSE
Adjust
the water level
according
If the water level is not
SPIN
to the amount of
laundry.
selected, it is automatically
set to
[LARGE].
RINSEONLY?
?
?
When it is desirable to rinse clothes which have
already
been washed.
Press the RINSE button to select the number of rinses.
Adjust
the water level
according
If the water level is not
WASH
to the amount of
laundry.
selected, it is automatically
set to
[LARGE].
To deposit
RINSE
AUTO OFF
fabric softener... Select the SOFTENER program,
then it indicates the time for depositing fabric softener.
SPIN
In this case, amount of
When
RINSE&SPIN?
?
?
selecting
rinse
laundry will not be sensed.
only, it starts with water supply.
When it is desirable to rinse and
spin
clothes which have
already been washed.
Press the RINSE button to select the number of rinses.
Press the SPIN button to select the
WASH
Adjust
RINSE
the water level
according
If the water level is not
SPIN
spinning
time.
to the amount of
laundry.
selected, it is automatically
set to
[LARGE].
DRAINorSPINONLY?
?
?
When it is desirable to drain water from the bowl
spin
WASH
clothes before
drying.
Press the SPIN button to select the
RINSE
spinning
time.
SPIN
WASH&SPIN?
?
?
When
heavy soiling
is removed
prior
to normal
washing
WASH
RINSE
SPIN
20
P/No.3828EA3006Q
Press the WASH and SPIN button to select the time.
or
Deposit laundry
Press the START/PAUSE
Deposit detergent
button
the lid
and close
START
PROGRAM
PAUSE
Deposit detergent
based
on
the
indicated amount.
If
The washer
of
displays the amount
detergent and begins supplying
water.
only [WASH
selected,
it is
For
or
WASH+RINSE]
is
water will not be drained after
completed.
draining, press
the SPIN button and
the START/PAUSE button.
Close the lid
Press the START/PAUSE
button
START
PROGRAM
PAUSE
Electric power turns off automatically
10 seconds after the alarm sounds,
when
washing completely finishes.
CAUTION
In
case
of
selecting
RINSE and
SPIN,
RINSE
or
water will be
before
starting RINSE,
by SPIN.
of selecting RINSE only,
supplied
followed
In
case
water will not be drained after
Check
pockets
belongings.
for
If the lid is not
the washer
sound.
completely closed,
generates the alarm
RINSE. To drain water, select
SPIN.
If the water level is not
is
automatically
set to
selected, it
[LARGE].
21
P/No.3828EA3006Q
WASHING PROCEDURE
Here is the
of
description
washing cycle programmed
Auto-Water
Programmed
Wash Cycles
Level
Setting
EX-LARGE
into the
Washing
21 min.
max.
10~15min.
NORMAL
SMALL
EX-LARGE
3 min. min
21 min.
max.
10~15min.
JEAN
SMALL
3 min. min
DELICATE
LARGE
10 min.
SPEEDY
MEDIUM
10 min.
WOOL
LARGE
5 min.
washing
machine memory.
Rinsing
Spinning
~
Deep2
Spray rinse + Deep1
63 min.
5 min.
~
~
34 min.
1 min.
7 min.
DEEP rinse is 3min a time
~
63 min.
5 min.
Deep2
Spray rinse + Deep1
~
34 min.
~
1 min.
DEEP2
(3
required
(Approx.)
7 min.
DEEP rinse is 3min a time
min.a
Time
time)
1 min.
55 min.
3 min.
38 min.
1 min.
51 min.
NORMAL
(PROCESS)
60 min.
SMALL
INFORMATION
The time
DEEP2
(3
min.a
time)
123 min.
DEEP rinse is 3min a time
EX-LARGE
SOAK
Spray rinse + Deep1
Deep2
Spray rinse + Deep1
1~7min.
~
94 min.
:
required
cycle may differ depending on the water pressure. The time shown on the
Table is set under the situation of water supply for approx. 3min.per cycle(20 liters per minute EX-LARGE
water
for each
level).
The indication shown
by
is the standard time.
NOTE:
High
water pressure may cause noise
if the noise is
annoying.
22
P/No.3828EA3006Q
during
the water
supply.
Turn the water
tap
to
adjust water supply
WATER LEVEL AND AMOUNT OF DETERGENT
AMOUNT OF DETERGENT
WATER
LEVEL
AMOUNT
OF WATER
EX-LARGE
AMOUNT
OF LAUNDRY
94~98L
REGULAR
Less than
8.5~9.0kg
80~86L
About
70~76L
60~69L
55~62L
40~45L
SMALL
About
76g
About
69g
About
62g
About
54g
About
45g
Less than
3.0~3.5kg
50~54L
86g
Less than
4.0~4.5kg
MEDIUM
About
Less than
5.0~5.5kg
Less than
2.0kg
Less than
1.0kg
About
65g
About
57g
About
51g
About
46g
About
41g
About
36g
About
30g
98g
Less than
6.5~7.0kg
LARGE
CONCENTRATED
Concentrated
detergent: 20g per 30 liters of water.
Regular synthetic detergent: 30g per 30 liters of water.
When sensing water levels automatically, the amount of water
even
For
can
differ
according
to the amount of
laundry
at the same water level.
synthetic detergent,
use one
that
generates less bubbles. This type of detergent is specially designed
for washers.
In
case
bleach
of using liquid detergent,
deposit hole.
dissolve it with
water(detergent: water=1:1)
and
deposit
it
through
the
Detergent
Use correct amount of
When
washing
detergent according
woollens remember to
to the
use a
detergent manufacturer's instruction.
detergent recommended by Australian Wool
Board
or
New
Zealand Wool Board.
We recommend the
Do not
use
CAUTION
detergents which are low sudsing and dissolve readily to obtain the best wash results.
detergent, which may cause an over sudsing problem and decrease rinsing efficiency.
use
too much
of
If you use laundry soap(natural resin) regularly, dirt separated from
remain on the inner-tub wall and cling to laundry during washing.
Using
excessive amount of
detergent
laundry
may reduce the rinse effect and
may
pollute
the
environment.
23
P/No.3828EA3006Q
HOW TO USE THE BLEACH AND THE SOFTENER
How to
When
use
the bleach agent
using bleach, always
Pour the
make
sure
powdered bleaching agent
only for bleaching.
it is
after
oxygenated
bleach.
separating
the clothes
Pour the
liquid bleaching agent
washing
cask.
How to
use
Bleach inlet
into the
the softner agent
detergent box by pulling in the direction of the arrow, as indicated in the picture.
detergent box with softener, making sure not to fill over the standard line, as indicated
Push the box closed slowly and gently so as not to allow the softener to spill out.
The softener will be automatically released at the proper time.
Open
the
Fill the
in the
picture.
Softner cap
Detergent
inlet
Limited line
If the softner is
it
Powder
detergent
box
can
flow
over
filled,
over.
Softner inlet
CAUTION
Don't
When
detergent. Use softener in last rinse water.
using dispenser, dilute softener(30ml) with fresh water(30ml)
When
filling dispenser,
use
softener with
do not
splash
or
overfill. It may stain clothes.
Never pour fabric softener and bleach
If
spotting
The
occurs, wet and rub hand
rewash.
only liquid fabric softener.
manually (during the last rinse cycle) when water pressure is too weak
than
0.5
as
it
will not be possible for the softener to be released automatically.
(less
kg/cm2)
Do not leave the softener in the dispenser for more than two days.
It is important to clean the dispenser regularly.
dispenser
is
directly on clothes. It may stain them.
dishwashing liquid (or mild bar soap) and
designed
Softener should be added
24
P/No.3828EA3006Q
to use
SELECTING EACH BUTTON
In addition to full-automatic
When the washer is in
Water
supply
By pressing
the
Even when
only
washing, the user can select other functions as desired.
operation, pause the washer before making changes.
selection
button, it cycles WARM(COLD & HOT) HOT COLD WARM.
HOT is selected, COLD water is supplied during the RINSE cycle.
Water LEVEL selection
Water level is set
change
automatically
after
sensing
the amount of
laundry.
Press the WATER LEVEL button to
the water level.
Stain Level selection
clothes
HEAVEY
Heavily-stained
MEDIUM
Normally-stanied clothes, cotton,
Lightly-stained
LIGHT
yam,
synthetic fabric,
Except for WOOL and
detergent,
DELICATE program.
the washer starts operating at
level which is
lower than the
To dissolve
thin clothes
clothes
one
step
preset
a
water level.
Wash selection
SOAK
21
10
-
21 min.
Heavily
15 min.
Normal clothes, cotton, yam,
5
5 min.
stained clothes, thick clothes
synthetic fabric, normally-stained clothes,
Soft clothes, delicate clothes,
Actual wash time may differ according to water level.
For WOOL program, washing wings rotate very slowly(to
lightly-stained
thin clothes
clothes
prevent shrinkage and damage).
Rinse selection
Rinse 2~4
Rinse 1
Heavily
stained clothes
Normal clothes, cotton, yam,
Spin
synthetic fabric, normally-stained clothes,
thin clothes
selection
7min.
Thick clothes
5min.
Normal clothes,
3min.
Soft clothes
For WOOL and DELICATE program,
the tub turns very slowly and spins
for a very short time
Clothes to be ironed, delicate clothes
(to prevent damage
1min. at low revolution
speed
light clothes, thin clothes
to
clothes).
Child Lock Selection
To
guard against
unwanted alteration of
cycle settings during operation,
the child lock may be utilised.
HOW TO LOCK
1Press
the POWER
2
button
Press the START/PAUSE
key
washing conditions are
according to the manual.
after all
set
AUTO OFF
Preset all
3
Press both the RINSE
key and the
key simultaneously while wash is
proceeding, then all the keys are locked
until completing the wash program or
unlocking them.
SPIN
washing
conditions.
PROGRAM
RINSE
START
SPIN
PAUSE
"CJ"
shown
HOW TO UNLOCK
If you want to unlock
during
wash press both the water
temp key and the
& the
on
remaining time are altematively
diplay while they are locked.
the
water level
key simultaneously again
25
P/No.3828EA3006Q
MAINTENANCE
CLEAN THE FILTER IN THE VALVE
Clean the filter when water
1Disconnect
supply
the power cord.
2
into the tub appears dirty or the inlet valve is clogged with impurity.
Pull out the filter from the
Use a tooth brush to get rid of
3
inlet valve.
dirt.
Replace
it.
CLEAN THE LINT FILTER
out the waste thread
1Pull
collection net from the tub in the
direction of the
arrow
2
Turn inside out to
a
Insert it into the
Do not rub the cabinet with
When you use
instructions.
CLEAN THE PUMP CASING
Unfasten 2
screws on
the back
cover.
2
Turn the cap as indicated
the arrow and unfasten it.
Remove
:
Check it
over
26
P/No.3828EA3006Q
a
chemical
or wax.
a
scrubbing
brush.
dustcloth, follow the
(when drainage is bad)
as
CAUTION
location.
Do not pour water directly on the cabinet.
Do not wipe the cabinet with benzine, thinner,
panel
soft cloth.
cleanser, alkaline detergent
1
original
CAUTION
stains from the cabinet
and the control
with
3
below.
CLEAN THE CABINET
Wipe
get
rid of filth.
foreign objects
pins, buttons, coins;
if water leaks after
by
3
such
Reassemble the cap as
by the arrow and
indicated
fasten it.
etc.
(Bottom view)
reassembling.(Rubber ring
is in the
(Bottom view)
cap)
CLEANING THE INSIDE OF YOUR WASHER
If you use fabric softener
inside of your machine.
or
do
regular
cold water
washing,
Fill your machine with hot water. Add about two cups of
Let it rotate for several minutes.
Stop
After
the
machine, open the lid. and leave it
soaking,
drain the machine and
run
a
it is
important
that you
powder detergent
occasionally
that contains
clean the
phosphate.
to soak
overnight.
through a regular cycle.
this
during
procedure.
the machine
We do not recommend that you wash clothes
WHEN THERE IS A FEAR OF FREEZING
1 Close the water
2 Hold the water
taps and
supply
remove
hoses
as
the water
supply hoses.
drawing so that
shown in the
it
does not sag.
3 Set the POWER button to "ON" and the WATER TEMP. to
4 Press START/PAUSE button and
warm.
operate the washing machine for
20 seconds.
Water which remains in the water
5
6
supply is removed.
Press START/PAUSE button to stop the operation.
Lower the drain hose and select manual spin mode.
7 Press START/PAUSE button and
operate for
30 seconds.
Set the POWER button to "OFF".
Drain the water in the bowl and the drain hose.
IF FROZEN
1 Remove the water
supply hose,
and immerse it in
hot water at approx. 40°C.
2 Pour approx. 2 liters of hot water at approx.
into the bowl for 10 minutes.
3 Connect the water
washing
machine
40°C,
supply hose to the water tap, and confirm that
performs the supply and drainage of water.
the
27
P/No.3828EA3006Q
If
an
abnormal
symbol appears in the display window, check the following before asking for service.
for the service center or agent in the case of failure or damage except for the following.
Request
appliance is fitted with a safety function that automatically stops
when it is exposed to jean disturbance on the mains.
This
SYMPTOM
the
operation
of the
washing
machine
ITEM TO BE CHECKED
Abnormal faucet
Is the water
Abnormal.
Water
Is the faucet
Is the faucet frozen? pressure lowered or cold water hose is connected to
the filter clogged?
Is water supply
the cold valve?(In this case, select
closed?
supply.
discontinued?
Abnormal
Is hot water selected when
cold
only
a
water.)
drainage
Check if electric
Check that the
Is the drain hose
Check whether the
power has gone
off.
drain hose is not
hung properly?
drain pump is
locked by foreign
twisted
or
kinked?
objects.
Abnormal
spin
Is the
Opened
laundry gathered
to
one
side?
Is the washer tilted?
lid
this time, buzzer sounds
without lamp indication)
(At
28
P/No.3828EA3006Q
Is the lid closed? If the lid is open, alarm
generated and rinse and spin cannot
is
proceed.
Is the lid closed after setting delayed
washing? If the lid is opened, delayed
washing cannot proceed.
SYMPTOM
Abnormal
ITEM TO BE CHECKED
sensor
Abnormal power
Ask for service center
Abnormal overflood
Abnormal Ball
sensor
No power
AUTO OFF
Is the power switch
Is the power
connected?
pressed?
plug firmly
Is power supply correct?
Is the short-circuit
breaker closed?
No
operation
PROGRAM
START
PAUSE
Is the lid closed and the
Is the tub filled with
START/PAUSE button
required
pressed?
water?
Is the faucet closed?
amount of
Excessive vibration and
noise
during spin
Is the washer installed
Water supply and rinse after
It is normal, the washer is
pausing it during spining
No
special
on
firm and level surface?
automatically correcting the laundry gathered to one side.
action is needed.
29
P/No.3828EA3006Q
Inlet water pressure
max
800 KPa
min 30 KPa
1029m
(115 psi)
(4 psi)
M90-12m Standpie inmuhegtofaps clrhetofmain
1 50m
alowingfor adjustblef
Electricity supply
688mm
Model
632mm
WF-T854A
Type
Electrical
8.5
(EX-LARGE
water
level)
Washing system
tap pressure
Outer dimension
Weight
30
P/No.3828EA3006Q
automatic washer
9.0
kg
See the
ratings
Standard amount of water
Water
WF-T902A
Fully
Washing capacity
240V
50 Hz sinusoidal
rating plate
attached to the
Approx. 94L
Automatic
rear
kg
of the washer
Approx. 98L
reverse
pulsator type
30-800kPa(0.3-8kgf/cm2)
632×688×1029(W×D×H)mm
632×688×1045(W×D×H)mm
47kg
31P는 백지
P/No.3828EA3006Q
P/No.: 3828EA3006Q
Download PDF

advertising