LG | 47LD462B | LG 32LD462B Owner’s Manual

OWNER’S MANUAL
LCD TV
Please read this manual carefully before operating
your set and retain it for future reference.
P/NO: MFL67162109 (1203-REV03)
Printed in Korea
www.lg.com
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
Separate purchase
Wall Mounting Bracket
LSW100B or
LSW100BG
(Only 32LD462B)
LSW200B or
LSW200BG
(Only 37/42/47LD462B)
Contents
Accessories...................................................... A-1
Front Panel Controls........................................ A-2
Back Panel Information.................................... A-3
Stand Installation.............................................. A-4
Not Using the Desk-Type Stand...................... A-4
Back Cover for Wire Arrangement................... A-5
Attaching the TV to a Desk.............................. A-5
How to use dual lockTM. ................................... A-6
Swivel Stand.................................................... A-6
Kensington Security System............................ A-6
Careful Installation Advice................................ A-7
Desktop Pedestal Installation........................... A-7
Wall Mount : Horizontal Installation................. A-8
Remote Control Key Functions........................ A-9
External equipment setup
Antenna Connection.............................................1
Connecting with a Component Cable..................2
Connecting with an HDMI Cable.........................3
Connecting with an HDMI to DVI Cable..............4
Connecting with an RCA Cable...........................4
Connecting with an RF Cable..............................5
Headphone Setup................................................5
Digital Audio Out Setup........................................6
Connecting with a D-sub 15 Pin Cable................7
Usb Setup............................................................7
Supported Display Resolution..............................8
Screen Setup for PC mode................................10
Watching TV / Programme control
Turning on the TV..............................................14
Initializing Setup ................................................14
Programme Selection.........................................14
Volume Adjustment............................................14
Quick Menu........................................................15
On Screen Menus Selection and Adjustment....16
Auto Programme Tuning....................................17
Manual Programme Tuning................................18
Programme Edit ................................................21
Software Update................................................24
Picture/Sound Test.............................................26
Signal Test..........................................................27
Product/Service Information...............................28
Selecting the Programme List............................29
Input List.............................................................30
Input Label.........................................................31
Data Service.......................................................32
AV Mode.............................................................33
Initializing(Reset to original factory settings).....34
CONTENTS
Preparation
To use a USB device
When connecting a USB device........................35
EzSign TV..........................................................37
Movie list............................................................39
Photo list.............................................................49
Music list.............................................................56
DIVX® VOD guide.............................................63
DIVX® VOD deregistration................................64
MHEG (MULTIMEDIA AND
HYPERMEDIA INFORMATION CODING
EXPERT GROUP)(IN DIGITAL MODE)
Teletext within Digital Service............................65
Teletext in Digital Service...................................65
Switch on MHEG ..............................................66
Select a Programme..........................................66
Button Function in Listing Mode........................67
Button Function in NOW/NEXT Mode...............67
I
CONTENTS
CONTENTS
Picture Control
Picture Size (Aspect Ratio) Control...................68
Picture Wizard....................................................70
Energy Saving....................................................71
Preset Picture Settings......................................72
Manual Picture Adjustment................................73
Picture Improvement Technology.......................75
Expert Picture Control........................................76
Picture Reset......................................................79
Power Indicator..................................................80
Sound & Language control
Auto Volume Leveler..........................................81
Clear Voice II......................................................82
Preset Sound Settings-Sound Mode.................83
Sound Setting Adjustment -User Mode.............84
Infinite Sound.....................................................84
Balance..............................................................85
TV Speakers On/ Off Setup...............................86
DTV Audio Setting (in digital mode only)...........87
Selecting Digital Audio out.................................88
Audio Reset........................................................89
I/II
Stereo/Dual Reception (In Analogue Mode Only)....90
NICAM Reception (In Analogue Mode Only).....91
Speaker Sound Output Selection......................91
On-Screen Menu Language / Country Selection.....92
Language Selection (In digital mode only)........93
Time Setting
Clock Setup........................................................95
Auto on/off time setting......................................96
Sleep Timer setting............................................97
Parental Control / Ratings
Set Password & Lock System...........................98
Block Programme...............................................99
Parental Control (In Digital Mode only)............100
External Input Blocking....................................101
Key Lock..........................................................102
II
Teletext
Switch on/off ...................................................103
SIMPLE Text....................................................103
TOP Text..........................................................104
FASTEXT.........................................................104
Special Teletext Functions...............................105
Appendix
Troubleshooting................................................106
Maintenance.....................................................108
Product Specifications......................................109
IR Codes.......................................................... 111
External Control Device Setup.........................112
Open Source Software Notice.........................119
Preparation
Accessories
Ensure that the following accessories are included with your TV. If an accessory is missing, please
contact the dealer where you purchased the TV.
preparation
■■ Image shown may differ from your TV.
Owner’s Manual
Batteries
(AAA)
EzSign TV Editor
S/W & Manual
Remote Control
This item is not included for all models.
* Lightly wipe any stains
or fingerprints on the
surface of the TV with
the polishing cloth.
Power Cord
Polishing Cloth
Do not use excessive
Polishing cloth for force. This may cause
use on the screen. scratching or discolouration.
x8
(M4 X 20)
1-screw for stand fixing
(Only 32/37/42LD462B)
Bolts for stand
assembly
Protection Cover
A-1
preparation
Front Panel Controls
preparation
NOTE
►►TV can be placed in standby mode in order to reduce the power consumption. And TV should
be switched off using the power switch on the TV if it will not be watched for some time, as this
will reduce energy consumption.
►►The energy consumed during use can be significantly reduced if the level of brightness of the picture
is reduced, and this will reduce the overall running cost.
CAUTION
►►Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from fragments
of glass, or the TV may fall.
►►Do not drag the TV. The floor or the product may be damaged.
P
■■ Image shown may differ from your TV.
P
PROGRAMME
P
OK
OK
MENU
INPUT
SPEAKER
VOLUME
MENU
OK
INPUT
MENU
OK
INPUT
POWER
MENU
Remote Control Sensor
Power/Standby Indicator
(Can be adjusted using the Power
Indicator in the OPTION menu.)
A-2
INPUT
USB IN
Back Panel Information
2
3
4
5
6
VIDEO L/MONO AUDIO R
1
AV IN 2
10
preparation
H/P HDMI IN 2
■■ Image shown may differ from your TV.
2
11
6
(RGB)
7
9
8
6
Audio/Video Input
Connect audio/video output from an external
device to these jacks.
7
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI
(VIDEO) signal to HDMI/DVI port with DVI to
HDMI cable.
RGB/DVIANTENNA
AudioIN Input
onnect the audio from a PC or DTV.
C
8
Component Input
Connect a component video/audio device to
these jacks.
3
RGB IN Input
Connect the output from a PC.
9
Antenna / Cable Input
Connect antenna or cable to this jack.
4
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of
equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
10
USB Input
Connect USB storage device to this jack.
11
Headphone Socket
Plug the headphone into the headphone
socket.
1
2
5
Power Cord Socket
This TV operates on an
1 AC power. The voltage is indicated on the Specifications page.
Never attempt to operateHDMI
the/ DVITV
IN on DC
power.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
A-3
preparation
Not Using the DeskType Stand
Stand Installation
■■ Image shown may differ from your TV.
preparation
When assembling the desk type stand, check
whether the bolt is fully tightened. (If not tightened
fully, the product can tilt forward after the product
installation.) If you tighten the bolt with excessive
force, the bolt can deviate from abrasion of the
tightening part of the bolt.
1
■■ Image shown may differ from your TV.
when installing the wall-mounted unit, use the protection cover.
Insert the Protection cover into the TV until
clicking sound.
Carefully place the TV screen side down
on a cushioned surface to protect the
screen from damage.
M4X20
Protection cover
2
Assemble the parts of the Stand Body with
the Stand Base of the TV.
Stand Body
M4X20
M4X20
M4X20
Stand Base
3
Assemble the TV as shown.
M4X20
4
Fix the 4 bolts securely using the holes in
the back of the TV.
M4X20
M4X20
M4X20
A-4
M4X20
AC IN
Back Cover for Wire
Arrangement
AC IN
(Only 32/37/42LD462B)
■■ Image shown may differ from your TV.
1
Connect the cables as necessary.
To connect additional equipment, see the
External equipment setup section.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially causing injury or damaging the product. Use
only an attached screw.
AC IN
preparation
■■ Image shown may differ from your TV.
Attaching the TV to a
Desk
AC IN
AC IN
CABLE MANAGEMENT
AC IN
2
Open the Cable Management Clip as
shown and manage the cables.
AC IN
1-Screw (provided as parts of the product)
AC IN
CABLE MANAGEMENT
AC IN
AC IN
Stand
AC IN
AC IN AC IN
3
Cable Management Clip
Desk
Fit the Cable management clip as shown.
AC IN
AC IN
AC IN
AC IN
NOTE
►Do
► not use the CABLE MANAGEMENT CLIP
to lift the TV.
-If the TV is dropped, you may be injured or the
TV may be damaged.
WARNING
►To
► prevent TV from falling over, the TV
should be securely attached to the floor/wall
per installation instructions. Tipping, shaking,
or rocking the machine may cause injury.
A-5
preparation
How to use dual lockTM Kensington Security
■■ This feature is not available for all models.
System
preparation
Fix the set-top box to the TV and use it when you want to. ■■ This feature is not available for all models.
■■ Image shown may differ from your TV.
After removing the protection paper from
the Dual Lock, stick it to the TV and the set- The TV is equipped with a Kensington Security
top box as shown.
System connector on the back panel. Connect
the Kensington Security System cable as shown
below.
For the detailed installation and use of the
Kensington Security System, refer to the user’s
guide provided with the Kensington Security
System.
For further information, contact http://www.kensington.com, the internet homepage of the
Kensington
company. Kensington sells security systems for
expensive electronic equipment such as notebook PCs and LCD projectors.
Attach the set-top box to the TV by pressing
the Velcro strips together.
1
2
Swivel Stand
NOTE
►►The Kensington Security System is an
optional accessory.
►If
► the TV feels cold to the touch, there may
be a small “flicker” when it is turned on.
►►Some minute dot defects may be visible on
the screen, appearing as tiny red, green, or
blue spots. However, they have no adverse
effect on the monitor's performance.
►► Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
■■ Image shown may differ from your TV.
After installing the TV, you can adjust the TV set
manually to the left or right direction by 20
degrees to suit your viewing position.
AC IN
CABLE MANAGEMENT
A-6
Careful Installation
Advice
Power
Supply
Circuit
breaker
2
2
2
Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are
not possible, have a qualified electrician install a
separate circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
1
1
1
EARTHING
preparation
■■ You should purchase necessary components
to fix the TV safety and secure to the wall on
the market.
■■ Position the TV close to the wall to avoid the
possibility of it falling when pushed.
■■ The instructions shown below are a safer way
to set up the TV, by fixing it to the wall, avoiding the possibility of it falling forwards if pulled.
This will prevent the TV from falling forward
and causing injury. This will also prevent the
TV from damage. Ensure that children do not
climb or hang from the TV.
■■ The TV can be installed in various ways such as
on a wall, or on a desktop etc.
■■ The TV is designed to be mounted horizontally.
Use the eye-bolts or TV brackets/bolts to fix the
product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then
bolts.)
* Insert the eye-bolts or TV brackets/bolts and
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the
wall. Match the height of the bracket that is
mounted on the wall.
Desktop Pedestal
Installation
For adequate ventilation allow a clearance of 10
cm all around the TV.
10 cm
10 cm
10 cm
10 cm
3
3
Use a sturdy rope to tie the product for alignment.
It is safer to tie the rope so it becomes horizontal
between the wall and the product.
NOTE
►►When moving the TV undo the cords first.
►►Use a platform or cabinet strong and large
enough to support the size and weight of the TV.
►►To use the TV safely make sure that the height of
the bracket on the wall and on the TV is the
same.
A-7
preparation
Wall Mount : Horizontal
Installation
A
preparation
B
■■ We recommend the use of a LG Brand wall
mounting bracket when mounting the TV to a wall.
■■ We recommend that you purchase a wall mounting bracket which supports VESA standard.
■■ LG recommends that wall mounting be performed by a qualified professional installer.
Model
VESA
(A * B)
Standard
Screw
Quantity
32LD462B
200 * 100
M4
4
37/42/47
LD462B
200 * 200
M6
4
NOTE
►Should
►
Install wall mount on a solid wall perpendicular to the floor.
►Should
►
use a special wall mount, if you want
to install it to ceiling or slanted wall.
►The
►
surface that wall mount is to be mounted on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block.
►Installing
►
screw type and length depends on
the wall mount used. Further information,
refer to the instructions included with the
mount.
►LG
► is not liable for any accidents or damage
to property or TV due to incorrect installation:
- Where a non-compliant VESA wall mount
is used.
- Incorrect fastening of screws to surface
which may cause TV to fall and cause personal injury.
- Not following the recommended Installation
method.
10 cm
10 cm
10 cm
10 cm
A-8
Remote Control Key Functions
When using the remote control, aim it at the remote control sensor on the TV.
In Analogue TV and some countries, some remote control keys may not work.
(POWER) Switches the TV on from standby or off to standby.
ENERGY AV MODE
ENERGY Adjust the Energy Saving mode of the TV.(► p.71)
SAVING
INPUT
TV/
RAD
AV MODE It helps you select and set images and sounds
when connecting AV devices.(► p.33)
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
INPUT External input mode rotate in regular sequence.(►
p.30)
TV/RAD Selects Radio, TV and DTV channel.
MARK
FAV
PORTAL
0~9 number Selects a programme.
button Selects numbered items in a menu.
LIST Displays the programme table.
Q.VIEW Returns to the previously viewed programme.
P
MUTE
MENU
preparation
■■ Image shown may differ from your TV.
GUIDE Q.MENU
P
A
G
E
MENU Selects a menu.
Clears all on-screen displays and returns to TV
viewing from any menu.(► p.16)
GUIDE Shows Contents List in EzSign mode. (EzSign V1.5
or Later)
Q. MENU Select the desired quick menu source. (► p.15)
THUMBSTICK Allows you to navigate the on-screen menus and
(Up/Down/Left/Right) adjust the system settings to your preference.
OK
OK Accepts your selection or displays the current
mode.
BACK INFOvl EXIT
BACK Allows the user to move return one step in an interactive application or other user interaction function.
INFO i Shows or hides the information on TV remote control
buttons in EzSign mode.
EXIT Clears all on-screen displays and returns to TV
viewing from any menu.
RATIO
Coloured These buttons are used for teletext (on TELETEXT
buttons models only), Programme edit.
A-9
preparation
ENERGY AV MODE
VOLUME UP Adjusts the volume. /DOWN
INPUT
preparation
TV/
RAD
MARK Select the input to apply the Picture Wizard
settings.
Check and un-check programmes in the USB
menu.
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
FAV Displays the selected favourite programme.
PORTAL Displays the EzSign content on a TV Screen.
MUTE Switches the sound on or off.
Programme Selects a programme.
UP/DOWN
MARK
FAV
PORTAL
P
MUTE
MENU
PAGE UP/ Move from one full set of screen information to the
DOWN next one.
P
A
G
E
1
GUIDE Q.MENU
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section.(► p.103)
SUBTITLE Recalls your preferred subtitle in digital mode.
OK
BACK INFOvl EXIT
MY MEDIA Controls MY MEDIA menu.
Menu
control buttons
1
RATIO Selects your desired Aspect Ratio of picture.
(►p.68)
RATIO
Installing Batteries
■■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■■ Install two 1.5 V AAA batteries. Do not mix old or used batteries with new ones.
■■ Close cover.
■■ To remove the batteries, perform the installation actions in reverse.
A-10
External equipment setup
■■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.
Antenna Connection
■■ For optimum picture quality, adjust antenna direction.
■■ An antenna cable and converter are not supplied.
CABLE MANAGEMENT
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Antenna
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75 Ω)
external equipment setup
AC IN
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
UHF
Signal
Amplifier
VHF
■■ In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier
to the antenna as shown above.
■■ If signal needs to be split for two TVs, use an antenna signal splitter for connection.
1
external equipment setup
■■ To avoid damaging any equipment, never plug in any power cord until you have finished connecting
all equipment.
■■ This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the
32/27/42/47LD462B models.
■■ Image shown may differ from your TV.
Connecting with a Component Cable
external equipment setup
■■ This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you
do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
1
Connect the video outputs (Y, PB, PR) of the external equipment (digital set-top box, DVD, etc.) to
the COMPONENT IN VIDEO jacks on the TV.
2
Connect the audio output of the external equipment (digital set-top box, DVD, etc.) to the
COMPONENT IN AUDIO jacks on the TV.
3
Turn on the external equipment.
(Refer to the external equipment's manual for operating instructions.)
4
Select the Component input source using the INPUT button on the remote control.
1
2
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
2
Component ports on the TV
Y
PB
PR
Video output ports
on DVD player
Y
Y
Y
Y
PB
B-Y
Cb
Pb
PR
R-Y
Cr
Pr
►►HDMI Audio Supported format : Dolby Digital, PCM
DTS Audio format is not supported.
Component
HDMI
480i/576i
480p/576p
720p/1080i
O
O
O
O
X
O
O
1080p
(50 Hz / 60 Hz only)
external equipment setup
Signal
O
(24 Hz / 30 Hz / 50 Hz / 60 Hz)
Connecting with an HDMI Cable
1
Connect the HDMI output of the external equipment (digital settop box, DVD, etc.) to HDMI/DVI IN 1 or HDMI IN 2 jack on the
TV.
2
Turn on the external equipment.
(Refer to the external equipment's manual for operating
instructions.)
3
Select HDMI1, HDMI2 input source using the INPUT button on
the remote control.
1
NOTE
►►The TV can receive video and audio signals simultaneously when
using an HDMI cable.
►►If the DVD does not support Auto HDMI, you must set the output resolution appropriately.
►►Check that your HDMI cable is High Speed HDMI Cable. If the HDMI
cables are not High Speed HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable.
►►The TV set can process audio format of PCM or Dolby Digital, when
connect the external equipment using an HDMI cable.
3
external equipment setup
Connecting with an HDMI to DVI Cable
external equipment setup
1
Connect the digital set-top box or the DVI output of the PC to HDMI/DVI IN 1 jack on the
TV.
2
Connect the audio output of the digital set-top
box or the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
3
Turn on the digital set-top box or the PC and
the TV.
(Refer to the digital set-top box or the PC
manual for operating instructions.)
4
Select HDMI1 input source using the INPUT
button on the remote control.
1
2
or
Connect the AUDIO/VIDEO jacks between TV
and VCR or external equipment.
2
Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.)
Or, Operate the corresponding external equipment.
(Refer to external equipment operating guide.)
3
1
H/P
1
IN 3
Connecting with an RCA Cable
Select AV1 input source using the INPUT button on the remote control.
If connected to AV IN 2 input, select AV 2
input source.
or
AV IN2
NOTE
►►If you have a mono VCR, connect the audio cable from
the VCR to the AUDIO L/MONO jack of the TV.
Video Game Set
Camcorder
4
Connecting with an RF Cable
■■ To avoid picture noise (interference), allow adequate distance between the VCR and TV.
Connect the ANT OUT socket of the VCR to
the ANTENNA / CABLE IN socket on the TV.
2
Connect the antenna cable to the ANT IN
socket of the VCR.
3
1
2
Press the PLAY button on the VCR and match
the appropriate channel between the TV and
VCR for viewing.
Wall Jack
Antenna
external equipment setup
1
Headphone Setup
2
To adjust the headphone volume, press the
+ or - button. If you press the MUTE button, the sound from the headphone is
switched off.
H/P
NOTE
AV IN2
H/P
Plug the headphone into the headphone
socket.
IN 3
1
IN 3
You can listen the sound through the headphone.
AV IN2
►►AUDIO menu items are disabled when connecting a headphone.
►►When changing AV MODE with a headphone connected, the change is applied to video but not to audio.
►►Optical Digital Audio Out is not available when connecting a headphone.
►►Headphone impedance: 16 Ω
►►Max audio output of headphone: 10 mW to 15 mW
5
external equipment setup
Digital Audio Out Setup
Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL
DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
external equipment setup
1
Connect one end of an optical cable to the TV
Digital Audio (Optical) Output port.
2
onnect the other end of the optical cable to
C
the digital audio (Optical) input on the audio
equipment.
3
1
Set the “TV Speaker option - Off ” in the
AUDIO menu.(►p.86). Refer to the external
audio equipment instruction manual for operation.
2
CAUTION
►►Do not look into the optical output port. Looking at the laser beam may damage your vision.
NOTE
►►When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV
speakers off.
6
Connecting with a D-sub 15 Pin Cable
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's
settings.
Connect the RGB output of the PC to the RGB
IN (PC) jack on the TV.
2
Connect the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
3
Turn on the PC and the TV
4
Select RGB input source using the INPUT button on the remote control.
1
2
external equipment setup
1
Usb Setup
1
Connect the USB device to the USB IN 1 or
USB IN 2 jack on the TV.
1
2
or
After connecting the USB IN 1 or USB IN 2
jack, you use the USB function. (► p.35)
7
external equipment setup
Supported Display Resolution
RGB-PC, HDMI-PC mode
external equipment setup
8
Resolution
Horizontal
Frequency(kHz)
HDMI-DTV mode
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
31.469
59.94
720x400
31.468
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x768
47.78
59.87
1360x768
47.72
59.80
45
60
1280x1024
63.981
60.02
33.72
59.94
66.587
59.93
33.75
60
28.125
50
67.5
60.00
26.97
23.97
27
24
33.716
29.976
33.75
30.00
1920x1080
(RGB-PC)
1920x1080
(HDMI-PC)
720x480
720x576
1280x720
1920x1080
31.5
60
31.25
50
37.5
50
44.96
59.94
56.25
50
67.43
59.94
67.5
60
NOTE
►►Connect the audio cable from the PC to the Audio
input on the TV. (Audio cables are not included with
the TV).
►►If using a sound card, adjust PC sound as required.
►►If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only
one of either RGB or HDMI IN (or HDMI/DVI IN) to
display the PC output on the TV.
►►If the graphic card on the PC does output analogue
and digital RGB simultaneously, set the TV to either
RGB or HDMI; (the other mode is set to Plug and
Play automatically by the TV.)
►►DOS mode may not work depending on the video
card if you use an HDMI to DVI cable.
►►If you use too long an RGB-PC cable, there may be
interference on the screen. We recommend using
under 5m of cable. This provides the best picture
quality.
external equipment setup
►►Avoid keeping a fixed image on the set’s screen
for prolonged periods of time. The fixed image
may become permanently imprinted on the
screen; use a screen saver when possible.
►►There may be interference relating to resolution,
vertical pattern, contrast or brightness in PC
mode. Change the PC mode to another resolution
or change the refresh rate to another rate or
adjust the brightness and contrast on the menu
until the picture is clear. If the refresh rate of the
PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of
the PC graphic card.
►►The synchronization input waveform for Horizontal
and Vertical frequencies are separate.
►►We recommend using 1920x1080, 60 Hz for
the PC mode, this should provide the best picture
quality.
►►Connect the signal cable from the monitor output
port of the PC to the RGB (PC) port of the TV or
the signal cable from the HDMI output port of the
PC to the HDMI IN (or HDMI/DVI IN) port on the
TV.
9
ExtErnal EquipmEnt sEtup
sCrEEn sEtup For pC moDE
screen reset
returns position, size and phase to the factory default settings.
piCture
move
• Brightness
50
• sharpness
70
• Colour
60
sCreen
OK
prev.
auto Config.
• tint
0
r
G
• Colour temp.
0
W
C
position
size
• advanced Control
• picture reset
screen
•• screen
move
resolution
►
external equipment setup
this function works in the following mode : rGB[pC].
to set
Yes
no
phase
reset
1
2
3
4
5
select piCturE.
select screen.
select reset.
select Yes.
run reset.
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
10
auto Configure (rgb [pC] mode only)
automatically adjusts the picture position and minimizes image instability. after adjustment, if the
image is still not correct, your tV is functioning properly but needs further adjustment.
piCture
move
• Brightness
50
• sharpness
70
• Colour
60
sCreen
OK
prev.
move
resolution
auto Config.
• tint
0
r
G
• Colour temp.
0
W
C
• advanced Control
size
►
• picture reset
screen
•• screen
position
auto Config.
Yes
external equipment setup
auto configure
this function is for automatic adjustment of the screen position, size, and phase the displayed image
will be unstable for a few seconds while the auto configuration is in progress.
no
phase
reset
1
2
3
4
5
select piCturE.
select screen.
• if the position of the image is still not correct,
try auto adjustment again.
• if picture needs to be adjusted again after
auto adjustment in rGB (pC), you can adjust
the position, size or phase.
select auto Config..
select Yes.
run auto Config..
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
11
ExtErnal EquipmEnt sEtup
selecting resolution
to view a normal picture, match the resolution of rGB mode and selection of pC mode.
piCture
move
• Brightness
50
• sharpness
70
• Colour
60
sCreen
OK
resolution
auto Config.
• tint
0
r
G
• Colour temp.
0
W
C
• advanced Control
• picture reset
screen
•• screen
position
move
prev.
1024 x 768
1280 x 768
1360 x 768
size
phase
►
external equipment setup
this function works in the following mode: rGB[pC]
reset
1
2
3
4
select piCturE.
select screen.
select resolution.
select the desired resolution.
5
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
12
adjustment for screen position, size, phase
this function works in the following mode : rGB[pC].
piCture
move
• Brightness
50
• sharpness
70
• Colour
60
sCreen
OK
auto Config.
• tint
0
r
G
0
W
C
• advanced Control
2
3
4
position
size
phase
• picture reset
1
prev.
resolution
• Colour temp.
►
screen
•• screen
move
external equipment setup
if the picture is not clear after auto adjustment and especially if characters are still trembling, adjust
the picture phase manually.
reset
select piCturE.
select screen.
select position, size or phase.
make appropriate adjustments.
5
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
13
Watching
Watching
TVTV
/ Programme
/ Programme
control
control
Turning on the TV
When your TV is turned on, you will be able to use its features.
Watching TV / Programme control
1
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
2
In standby mode to turn TV on, press the / I, INPUT or P
button on the TV or press
the POWER, INPUT, P
or NUMBER button on the remote control and the TV will
switch on.
Initializing Setup
1
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can
adjust the Language(Except for Australia, New Zealand, Singapore, South Africa), Power
Indicator(Only LED LCD TV models), Country (Only Australia, New Zealand), Time
Zone(Only Australia), Auto Tuning.
Note:
a.If you close without completing the initial setting, the Initial Setting menu can be displayed
again.
b.Press the BACK button to change the current OSD to the previous OSD.
c.For those countries without confirmed DTV broadcasting standards, some DTV features might
not work, depending on the DTV broadcasting environment.(Only DTV)
d."Home Use” mode is the optimal setting for home environments, and is the TV's default mode.
Programme Selection
1
Press the P
or NUMBER buttons to select a programme number.
Volume Adjustment
+ or - button to adjust the volume.
1
Press the
2
If you wish to switch the sound off, press the MUTE button.
You can cancel this function by pressing the MUTE,
14
+ , - or AV Mode button.
Quick Menu
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequen tly.
◄
Aspect Ratio
Audio or Audio Language : Select the
sound output.
Sleep Timer : Set the sleep timer.
Skip Off/On : Select the Skip Off/On.
USB Device : Selects “Eject” in order to eject
USB device. If EzSign Content is running via
USB, it may not work correctly after “USB Eject”
has been selected. So please remove the
attached USB Immediately after” USB Eject” has
selected
►
Watching TV / Programme control
Aspect Ratio: Select your desired picture format.
For Zoom Setting, select 14:9, Zoom and
Cinema Zoom in Ratio Menu. After completing Zoom Setting, the display goes back to
Q.Menu.
Clear Voice II : By differentiating the human
sound range from others, it helps users listen to human voices better.
Picture Mode : Select your desired Picture
Mode.
Sound Mode : It is a feature to automatically set the sound combination which it deems
the best for the images being watched.
Selects your desired Sound Mode.
16:9
Exit
1
2
3
Display each menu.
Select your desired Source.
• Press the Q.MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
15
WatCHing tV / programmE Control
on sCrEEn mEnus sElECtion anD aDjustmEnt
Your tV's OsD (On screen Display) may differ slightly from that shown in this manual.
setup
● auto
move
piCture
OK
tuning
● manual
tuning
● programme
edit
● aspect
ratio
● picture
Wizard
●ꕊ
WatCHinG tV / prOGramme COntrOl
● set
move
● auto
: 16:9
mode
system
● Clear
: standard
3
• Backlight
70
• Contrast
100
• Brightness
50
• sharpness
70
0
mode
l
: standard
r
• infinite sound : Off
• treble
50
• Bass
50
• reset
time
setup
● input
lock
piCture
auDiO
move
OK
Block
move
● Country
● set
: Off
time
: Off
timer
: Off
OK
input
OptiOn
input list
move
mY meDia
OK
mY meDia
: australia
of Hearing (ꔞ): Off
antenna
usB
HDmi1
HDmi2
aV1
aV2
Component
rGB
indicator
ezsign tV
reset
iD
● mode
time
● On
● sleep
● language(language)
● Factory
● Off
: Off
OptiOn
● Hard
● Clock
time
Guidance: Blocking Off
lOCK
● power
:1
setting
Blaster
1
: Off
select a menu item.
move to the pop up menu.
movie list
press OK(
: Home use
Display each menu.
2
input label
exit
photo list
music list
) to see photos from the usB.
Option
exit
• press the rED button, you can check the
Customer support menu.
• press the grEEn button, you can check
the simple manual menu.
• press the mEnu/Exit button to return to
normal tV viewing.
• press the baCk button to move to the previous menu screen.
notE
►it is possible to use Country menu in australia and new Zealand only.
►it is possible to use Hard of Hearing, parental guidance menu in DtV only.
16
: Off
programme
● parental
3
Voice ii
● Balance
● sound
OK
: Off
OK
: Off
● Block
● ir
move
Volume
password
● lock
● Key
auDiO
OK
energy saving : Off
● picture
lOCK
move
Auto Programme Tuning
Use this to automatically find and store all available programmes.
When you start auto programming, all previously stored service information will be deleted.
SETUP
Move
►
● Manual
Tuning
● Programme
SETUP
OK
►
● Auto Tuning
Edit
Move
● Manual
OK
Antenna
● Auto
Auto Tuning
Tuning
●
Tuning
● Programme
Edit
Antenna
Check your antenna connection. The
previous channel information will be
updated during Auto Tuning.
Automatic Numbering
Start
Close
1
2
3
4
Select SETUP.
Select Auto Tuning.
Select Start.
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
• If you wish to keep on auto tuning select
Start using the ꕌꕍ button. Then, press
the OK button. Otherwise select Close.
• Automatic Numbering: Decide whether
to use the programme numbers as sent
by broadcasting stations for tuning. (Only
DTV)
Watching TV / Programme control
■■ Image shown may differ from your TV.
Run Auto tuning.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
17
Watching TV / Programme control
Manual Programme Tuning
(In Digital Mode)(Only DTV)
Manual Tuning lets you manually add a programme to your programme list.
SETUP
OK
Tuning
● Auto
● Manual Tuning
● Programme
►
● Auto
Move
►
Watching TV / Programme control
SETUP
Edit
Move
OK
Tuning
◄
● Manual Tuning
● Programme
Edit
►
DTV
UHF CH.
30
Frequency(kHz)
474000
● Signal Strength
● Signal Quality
50%
50%
Update
Close
1
2
3
Select SETUP.
•U
se NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
Select Manual Tuning.
Select DTV.
4
Select the desired channel number.
5
Update.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
18
(In Analogue Mode)
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.
■■ Image shown may differ from your TV.
● Auto
Move
OK
Tuning
►
● Programme
►
● Manual Tuning
Edit
SETUP
Move
◄
● Auto
● Storage
3
● Manual Tuning
● System
● Programme
BG
● Band
Tuning
Edit
OK
►
TV
V/UHF
● Channel
0
● Fine
◄►
● Search
◄►
● Name
C 02
Store
Close
1
2
3
4
5
6
Select SETUP.
Select Manual Tuning.
7
8
Select TV.(Only DTV)
or
Select the desired
channel Storage.
9
Select V/UHF or Cable.
or
Select the desired
channel number.
Commence searching.
Watching TV / Programme control
SETUP
Select Store.
Select a TV system.
(Except for Australia)
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
•Use NUMBER buttons to input a 4-digit password in Lock System ‘On’.
•BG : PAL B/G (New Zealand / South Africa / Singapore / Indonesia / Israel / Malaysia / Vietnam / Asia)
DK : PAL D/K (New Zealand / South Africa / Singapore / Indonesia / Israel / Malaysia / Vietnam / Asia)
I : PAL I/II (New Zealand / South Africa / Singapore / Indonesia / Israel / Malaysia / Vietnam / Asia)
B/B : Australia
M : NTSC-M (South Africa / Indonesia / Israel / Malaysia / Vietnam / Asia)
•To store another channel, repeat steps 4 to 9.
19
Watching TV / Programme control
(In Analogue Mode)
■■ Image shown may differ from your TV.
◄
SETUP
SETUP
OK
Tuning
● Auto
● Programme
►
● Manual Tuning
►
● Auto
Move
Edit
►
TV
Move
●
StorageOK
3
● System
Tuning
● Manual Tuning
● Band
● Programme
● Channel
Edit
BG
V/UHF
0
● Fine
◄►
● Search
◄►
● Name
C 02
Watching TV / Programme control
Store
Close
■■Assigning a station name
You can assign a station name with five characters to each programme number.
1
2
3
4
Select SETUP.
5
Select Manual Tuning.
Select TV. (Only DTV)
6
Select Name.
7
Select the position and make
your choice of the second
character, and so on.
You can use an the alphabet
A to Z, the number 0 to 9, +/
-, and blank.
Select Close.
Select Store.
■■Fine Tuning
Normally fine tuning is only necessary if reception is poor.
1
2
3
Select SETUP.
4
Select Manual Tuning.
5
Select TV. (Only DTV)
6
Select Fine.
Fine tune for the best picture
and sound.
Select Store.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
20
Programme Edit
When a programme number is skipped, it means that you will be unable to select it using P
ton during TV viewing.
but-
If you wish to select the skipped programme, directly enter the programme number with the NUMBER
buttons or select it in the Programme edit menu.
This function enables you to skip the stored programmes.
■■ Image shown may differ from your TV.
Programme Edit
SETUP
Tuning
● Manual
Tuning
Edit
►
● Programme
Page 1/2
A
RADIO
DTV
OK
►
● Auto
Move
Favourite Group :
TV
800 YLE TV1
801 YLE TV2
802 YLE FST
803 YLE24
804 YLE Teema
805 TV4 Stockholm
806 Kanal Lokal
807 CNN
808 TV4
809 TV4 Plus
810 TV400
811 TV4 Film
812 TV4 Fakta
813 MediaCorp HD5
814 SNY_SSU
815 Demo
816 TVE 1
817 TVE 2
818 24H TVE
819 CLAN/50 TVE
820 LA7
▼
Pr. Change
P
1
2
3
4
Page Change
FAV
Favourite Pr.
Q.MENU
Favourite Pr. Group
Previous
Block/Unblock
Skip
Watching TV / Programme control
You can change the programme number using “Move”function, if “Automatic Numbering” is unchecked
when you start Auto Tuning.(Only DTV)
Select SETUP.
Select Programme Edit.
Enter the Programme Edit.
Select a programme to be stored or
skipped.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
21
Watching TV / Programme control
(In DTV/Radio Mode) (Only DTV)
■■Locking a programme number
1
• It can be registered as Lock
programme even when Lock
System is turned Off.
Select a programme number to be locked.
2
YELLOW Lock up the programme.
Watching TV / Programme control
3
YELLOW Release.
■■Skipping a programme number
1
Select a programme number to be skipped.
2
BLUE Turn the programme number to blue.
3
BLUE Release.
• When programmes are to be skipped, the
skipped programme shows in blue and
these programmes will not be selected by
the P ꕌꕍ buttons during TV viewing.
• If you wish to select a skipped programme,
directly enter the programme number with
the NUMBER buttons or select it in the
programme edit or EPG.
(In TV Mode)
This function enables you to delete or skip the stored programmes.
You can also move some channels and use other programme numbers.
■■Deleting a programme
1
Select a programme number to be deleted.
2
RED
•T
he selected programme is deleted, all the
following programmes are shifted up one.
Turn the programme number to red.
■■Moving a programme
1
2
GREEN
22
Select a programme number to be moved.
Turn the programme number to
green.
3
GREEN Release.
■■Locking a programme number
1
Select a programme number to be locked.
2
• It can be registered as Lock
programme even when Lock
System is turned Off.
YELLOW Lock up the programme.
3
YELLOW Release.
1
Select a programme number to be skipped.
2
BLUE Turn the programme number to blue.
3
BLUE Release.
• When a programme number is skipped it
means that you will be unable to select it
using the P ꕌꕍ button during normal TV
viewing.
• If you wish to select a skipped programme,
directly enter the programme number with
the NUMBER buttons or select it in the
programme edit.
■■Selecting favourite programme
Favorite programmes is a convenient feature that lets you quickly scan up to programmes of your
choice without having to wait for the TV to scan through all the in-between programmes.
1
Watching TV / Programme control
■■Skipping a programme number
Select your desired programme.
2 MARK
FAV
3 MARK
FAV
Add corresponding programme to Favourite
list of current Favourite group.
Release.
■■Selecting favourite programme group
1
2
3
Select your desired programme.
Display a pop-up window where
Favourite group can be changed.
Select a Favourite group.
23
Watching TV / Programme control
Software Update
You can update the TV with the latest software to enhance the product operation and/or add new features.
■■ Image shown may differ from your TV.
Watching TV / Programme control
Software Update
Software Update
◄ On ►
Picture Test
SETUP
PICTURE
AUDIO
TIME
Sound Test
● Current version
Signal Test
00.00.01
Product/Service Info.
Close
LOCK
OPTION
Press OK(
INPUT
) to set programme settings.
Customer Support
1
2
Exit Exit
RED Select Customer Support.
Select Software Update.
Select On or Off.
• If you select On, a user confirm message box will
be displayed to notify that new software is found.
3
4
Close
MY MEDIA
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
24
■■When setting “Software Update”
Occasionally, a transmission of
updated digital software information will result in the following
menu on the TV screen.
Software update is available.
Would you like to download now?
Yes
No
Simple Update : for current
update stream
Software Update
A window as display below
appears when download
completes.
TV is restarted when "Yes"
button is pressed.
New software version is ready. If you want
to install now, TV will be turned off and
restart. Continue?
◄ On ►
Software downloading progress.
Ver. 00.00.01 ► Ver.00.00.00
Yes
No
4%
Close
? A new software update is available at
00/00/0 00:00.
Do you want to update the software when
available?
Yes
No
Schedule Update : for scheduled
update stream
When the Software Update menu
is "Off", the message to change it
to "On" appears.
Watching TV / Programme control
?
Download starts when "Yes" is
selected. At this time, progressing pop-up window does
not display.
Download progress status can
be checked from Software
Update menu.
- During Progress of a Software Update, please note the following:
• Power to the TV must not be interrupted.
• After Software Update, you can confirm the updated software version in Software Update menu.
• It may take hours to download the software, so make sure that the power stays on during the download.
<Simple Update, Schedule Update>
• The antenna must not be disconnected.
• The software is downloaded only in Standby mode or in MUX with Software Update Service, and stops
when the power cord is unplugged or when viewing MUX without Software Update Service.
• When you return to Standby mode or MUX with Software Update Service, the software download will
resume from where it stopped.
25
Watching TV / Programme control
Picture/Sound Test
This function is a customer support function that can execute picture and sound tests.
■■ Image shown may differ from your TV.
Software Update
Watching TV / Programme control
SETUP
PICTURE
AUDIO
TIME
Picture Test
Sound Test
?
Do you have a problem in this test
screen?
Signal Test
Product/Service Info.
LOCK
OPTION
Press OK(
INPUT
2
3
No
Close
) to set programme settings.
Customer Support
1
MY MEDIA
Yes
Exit Exit
RED Select Customer Support.
Select Picture Test or Sound Test.
Select Yes or No.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
26
Signal Test
(Only DTV)
This function enables you to view information on the Manufacturer, Model/Type and Software Version.
This displays the information and signal strength of the tuned *MUX.
This displays the signal information and service name of the selected MUX.
(*MUX: A higher directory of channels in digital broadcasting (a single MUX contains multiple channels.))
Engineering Diagnostics
Software Update
SETUP
PICTURE
AUDIO
Picture Test
TIME
Manufacturer : LG Electronics Inc.
Model/Type : 42LE7500-TA
Software Version : V00.00.01
Sound Test
Signal
Signal Test
Test
Product/Service Info.
LOCK
OPTION
Press OK(
INPUT
MY MEDIA
Close
Ch 30
Ch 34
Ch 36
Ch 38
Ch 54
Ch 60
) to set programme settings.
Customer Support
Exit Exit
Prev.
1
2
3
4
Popup
MENU
Exit
RED Select Customer Support.
Watching TV / Programme control
■■ Image shown may differ from your TV.
Select Signal Test.
Display Manufacturer, Model/Type and Software Version.
Display the information of Channel.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
27
Watching TV / Programme control
Product/Service Information
This function is a customer support function that can see product/service information and customer service center
information.
■■ Image shown may differ from your TV.
Watching TV / Programme control
Software Update
SETUP
PICTURE
AUDIO
TIME
Picture Test
Sound Test
Signal Test
Product/Service Info.
LOCK
OPTION
Press OK(
INPUT
2
3
Close
) to set programme settings.
Customer Support
1
MY MEDIA
Exit Exit
RED Select Customer Support.
Select Product/Service Info..
Display Model/Type, Software version, Serial Number,
Used time, Customer service center and Homepage.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
28
Selecting the Programme List
You can check which programmes are stored in the memory by displaying the programme list.
Mini Glossary
Programme List
1 BBC
►
Displayed when the
Locked Programme.
Exit
2 BBC
3 BBC
5 BBC
A
Pr.Edit
■■Displaying programme LIST
1
Display the Programme List.
•Y
ou may find some blue programmes.
These have been set up to be skipped by
auto programming or in the programme
edit mode.
•S
ome programmes with the channel number shown in the programme LIST indicate
there is no station name assigned.
BLUE
Watching TV / Programme control
4 BBC
Turn the programme edit.
■■Selecting a programme in the programme list
1
2
The mode will be switched
between TV, DTV, and Radio
from the programme you are
currently watching.(Only DTV)
Select a programme.
Switch to the chosen programme number.
■■Paging through a programme list
1
Turn the pages.
2
Return to normal TV viewing.
29
Watching TV / Programme control
■■ Displaying the favourite programme list
Exit
Favourite List
1
Display the Favourite Programme List.
◄ ►Favourite Pr. Group
◄
Group
B
►
►
1 BBC
►
2 BBC
BLUE
Turn the programme edit.
YELLOW
Current channel is registered/
cancelled as preferred channel on
currently selected Group.
3 BBC
Watching TV / Programme control
Pr.Reg.
Favourite group is changed.
Pr.Edit
Input List
By using TV/RAD button, you can move from External Input to RF Input and to the last watched programme in DTV/RADIO/TV mode.(Only DTV)
■■ Image shown may differ from your TV.
Input List
Move
Antenna
USB
HDMI1
HDMI2
AV1
AV2
Component
Input Label
1
30
Select the input source.
OK
RGB
Exit
•A
ntenna : Select it when watching the TV.
(Only DTV : Select it when watching the
DTV/TV/RADIO.)
• USB : Select it when using USB depends
on connector.
• AV : Select it when watching the VCR or
external equipment.
• Component : Select it when using the
DVD or the Digital set-top box depends on
connector.
• RGB :Select it when using PC depends on
connector.
• HDMI : Select it when using DVD, PC or
Digital set-top box depend on connector.
Input Label
Selects a label for each input source.
■■ Image shown may differ from your TV.
Move
Antenna
USB
HDMI1
HDMI2
AV1
AV2
Component
Input Label
OK
RGB
Exit
AV1
◄
►
AV2
◄
►
Component
◄
►
RGB
◄
►
HDMI1
◄
►
▼
Close
1
2
3
BLUE Select Input Label.
Select the source.
Watching TV / Programme control
Input List
Input Label
Select the label.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
31
Watching TV / Programme control
Data Service
(This menu is enabled only in South Africa, Malaysia. )
This function allow users to choose between MHEG(Digital Teletext) and Teletext if both exist at the same
time.
If only one of them exists, either MHEG or Teletext is enabled regardless of which option you selected.
Move
Move
● Language(Language)
● Hard
● Hard
● Data Service
● Factory
● Set
Setting
1
MHEG
:: MHEG
Indicator
● Data Service
Reset
ID
● Mode
of Hearing (ꔞ): Off
● Power
►
Indicator
OK
● Factory
:1
● Set
: Home Use
● Mode
Reset
ID
Setting
MHEG
MHEGMHEG
:: MHEG
Teletext
►
of Hearing (ꔞ): Off
● Power
:1
: Home Use
Select OPTION.
2
Select Data Service.
3
4
OPTION
OK
● Language(Language)
►
Watching TV / Programme control
OPTION
Select MHEG or Teletext.
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
32
AV Mode
You can select the optimal images and sounds when connecting AV devices to external input.
Off
Cinema
Sport/Cricket
Game
Disables the AV MODE.
Optimizes video and audio for watching movies.
Optimizes video and audio for watching sports events.
Optimizes video and audio for playing games.
1 AV MODE
Off
Cinema
Game
Sport
Watching TV / Programme control
■■ Image shown may differ from your TV.
Press the AV MODE button repeatedly to select the desired source.
2
• If you select Cinema in AV mode, Cinema will be selected both for Picture Mode and Sound
Mode in PICTURE menu and AUDIO menu respectively.
• If you select “Off” in AV mode, the picture and image which you initially set will be selected.
• When playing a video game using PlayStation or Xbox, it is recommended to use the Game
mode.
• When in Game mode, functions related to picture quality will be optimized for playing games.
33
Watching TV / Programme control
Initializing(Reset to original factory settings)
This function initializes all settings.
But the settings of
Day and
Night of the Picture Mode cannot be initialized.
It is useful to initialize the product or when you move to other city or country.
When the Factory Reset is completed, you must restart the Initializing setup.
When the Lock System menu is "On", the message to enter the password appears.
Watching TV / Programme control
OPTION
Move
● Country
● Country
: Australia
of Hearing (ꔞ): Off
● Power
ID
● Mode Setting
3
4
OK
: Australia
of Hearing (ꔞ): Off
● Power
:1
Indicator
All user settings and channel settings will
be reset. Still Continue?
● Set ID
:1
: Home Use
● Mode Setting
►
►
● Set
● Hard
Indicator
● Factory Reset
2
Move
● Language(Language)
● Hard
1
OPTION
OK
● Language(Language)
Select OPTION.
● Factory Reset
: Home Use
Yes
No
• In Lock System "On", if you forget your
password, press '0', '3', '2', '5' on the
remote control handset.
Select Factory Reset.
Select Yes.
Start Factory Reset.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
34
To use a USB device
When connecting a USB device
When you connect a USB device, this pop up menu is displayed, automatically.
“POP UP MENU” will not be displayed while the OSD including Menu, EPG or Schedule list is activated.
When the Pop Up menu appears, you can select Music List, Photo List or Movie List in the MY MEDIA
menu.
In USB device, you can not add a new folder or delete the existing folder.
1 Connect the USB device to the USB IN
jack on the TV.
•O
nly photo(JPEG), music (MP3) and movie
(DAT,MPG,MPEG,VOB,AVI,DIVX,MP4,MKV,T
S,TRP,TP,ASF,WMV,FLV) are supported.
2
Select EzSign TV, Movie List,
Photo List or Music List.
■■ Image shown may differ from your TV.
When removing the USB device
Select the USB Device menu before removing
the USB device.
1
MY MEDIA
2
EzSign TV
Movie List
Press OK(
Photo List
Music List
To use a USB device
or
Select USB Device.
Select Eject.
) to see photos from the USB.
Option
Exit
3
35
To use a USB device
Precautions when using the USB device
To use a USB device
36
►►Only a USB storage device is recognizable.
►►If the USB storage device is connected through a USB hub, the device is not recognizable.
►►A USB storage device using an automatic recognition programme may not be recognized.
►►A USB storage device which uses its own driver may not be recognized.
►►The recognition speed of a USB storage device may depend on each device.
►►Please do not turn off the TV or unplug the USB device when the connected USB storage device is working.
When such device is suddenly separated or unplugged, the stored files or the USB storage device may be
damaged.
►►Please do not connect the USB storage device which was artificially maneuvered on the PC. The
device may cause the product to malfunction or fail to be played. Never forget to use only a USB storage device which has normal music files, image files or movie files.
►►Please use only a USB storage device which was formatted as a FAT32 file system, NTFS file system
provided with the Windows operating system. In case of a storage device formatted as a different utility
programme which is not supported by Windows, it may not be recognized.
►►Please connect power to a USB storage device(over 0.5 A) which requires an external power supply. If
not, the device may not be recognized.
►►Please connect a USB storage device with the cable offered by the device maker.
►►Some USB storage devices may not be supported or operated smoothly.
►►File alignment method of USB storage device is similar to Window XP and filename can recognize up to 100
English characters.
►►Be sure to back up important files since data stored in a USB memory device may be damaged. We
will not be responsible for any data loss.
►►If the USB HDD does not have an external power source, the USB device may not be detected. So be sure to
connect the external power source. - Please use a power adaptor for an external power source. We do not guarantee an USB cable for an external power source.
►►If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use
up to 4 partitions or USB memory devices.
►►If a USB memory device is connected to a USB multi-card reader, its volume data may not be detected.
►►If the USB memory device does not work properly, disconnect and reconnect it.
►►How fast a USB memory device is detected differs from device to device.
►►If the USB is connected in Standby Mode, specific hard disk will automatically be loaded when the TV is
turned on.
►►The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USB
memory.
►►Any device with more than the recommended capacity may not work properly.
►►If a USB external hard disk with a "Energy Saving" function does not work, turn the hard disk off and on
again to make it work properly.
►►USB storage devices below USB 2.0 are supported as well. But they may not work properly in the
movie list.
►►Maximum of 999 folders or files can be recognized under one folder.
►►The file arrangement of the USB storage device is similar to that of Windows XP and supports up to
100 alphabetical characters.
►►If there are a lot of folders or files all within one folder, the device may not be able to access these
properly.
EzSign TV
The EzSign TV function allows you to play and manage high-quality ad content that you create quickly
and easily using the EzSign TV Editor.
ꔛ For more information of using, refer to the EzSign TV Editor S/W & Manual.
■■ Image shown may differ from your TV.
TV memory
USB
EzSign TV content exists. How do you want
to manage this content?
Delete
Play
Close
MY MEDIA
or
TV memory
EzSign TV
Movie List
Photo List
USB
Music List
How do you want to play the EzSignTV content?
Play
Close
1
Select MY MEDIA.
2
Select EzSign TV.
3
Select TV memory or USB.
TV memory
Play
4
Select your desired Source.
5
ꔛ
The highlighted tab with the " " symbol
indicates the location of the file currently
being played.
To use a USB device
Copy to TV memory & Play
Plays EzSign TV content in the memory.
Delete
Deletes EzSign TV content from the memory.
• The TV restarts after the content is deleted.
Close
Closes the EzSign TV menu window.
USB
Copies a file from the USB memory to the EzSign TV memory and plays it.
Copy to TV memory
• Once the file has been copied, it can be played even when it is removed
& Play
from the USB memory.
Play
Close
Plays a file directly from the USB memory without copying it to the EzSign
TV memory.
Closes the EzSign TV menu window.
37
To use a USB device
Using the remote control
While the content is being played from a USB device or TV memory, you can press a TV remote control
button to switch to an EzSign mode or TV mode or see the content information.
EXIT
PORTAL
The mode is switched from EzSign to TV mode. The playing content or content list
disappears, and a regular TV broadcasting is displayed on the full screen.
The mode is switched from TV to EzSign mode. The screen stops regular TV broadcasting, and EzSign TV content is played.
Deselect all marked movie files.
INFO
Return to normal TV viewing.
To use a USB device
NOTE
►While
►
loading EzSign TV content, your TV may function slower than normal.
►It
► is recommended that you copy files to the TV memory before playing them, as playing directly
from the USB memory for an extended period of time may cause the device to overheat.
►In
► EzSign TV, some remote control keys may not work.
►►In EzSign mode, the content is played. Only in this mode, you can see the information related to the
EzSign contents (content screen, content list, TV remote button info, etc.)
►►In TV mode, regular TV broadcasting is displayed on a full screen with no playback of the content. In this
mode, you cannot see the content information using the Program Guide or information display key.
38
Movie list
You can play movie files on a USB storage device.
The movie list is activated once USB is detected. It is used when playing movie files on TV.
Displays the movies in the USB folder and supports Play.
Allows playback of all movies in the folder and user desired files.
It is a movie list that displays folder information and movie file.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
To use a USB device
Movie(*.mpg/*.mpeg/*dat/*.ts/*.trp/*.tp/*.vob/*.mp4/*.mov/*.mkv/*.divx/*.avi/*.asf/*.wmv/*.flv/*.
avi(motion-jpeg)/*.mp4(motion-jpeg)/*.mkv(motion-jpeg))supporting file
Video format : DivX3.11, DivX4.12, DivX5.x, DivX6, Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03,
Xvid1.10 beta-1/beta-2, Mpeg-1, Mpeg-2, Mpeg-4, H.264/AVC, VC1, JPEG, Sorenson
H.263
Audio format : Dolby Digital, AAC, Mpeg, MP3, LPCM, HEAAC, ADPCM, WMA
Bit rate : within 32 kbps to 320 kbps(MP3)
External Subtitle format : *.smi/*.srt/*.sub(MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.
psb(PowerDivX)
• Some user-created subtitles may not work properly.
• Some special characters are not supported in subtitles.
• HTML tags are not supported in subtitles.
• Subtitles in languages other than the supported languages are not available.
• Changing font and colour in subtitles is not supported.
• Subtitles in languages other than one specified are not supported.
• Video files with subtitle files of 1 MB or larger may not be played properly.
• The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the
audio language is changed.
• A damaged movie file may not be played correctly, or some player functions may not be usable.
• Movie files produced with some encoders may not be played correctly.
• If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.
• HD videos with a maximum of 1920x1080@25/30P or 1280x720@50/60P are supported, depending on the frame.
• Videos with resolutions higher than 1920X1080@25/30P or 1280x720@50/60P may not work
properly depending on the frame.
• Movie files other than the specified types and formats may not work properly.
• Max bitrate of playable movie file is 20 Mbps. (only, Motion JPEG : 10 Mbps.
• We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC.
• DTS Audio codec is not supported.
• A movie file more than 30 GB in file size is not supported for playback. The file size limit is dependent on the encoding environment.
• A DivX movie file and its subtitle file must be located in the same folder.
• A video file name and its subtitle file name must be identical for it to be displayed.
• Playing a video via a USB connection that doesn’t support high speed may not work properly.
• The movie file encoded by the GMC (Global Motion Compensation) and Qpel (Quarterpel Motion
Estimation) is not supported.
• When you are watching the movie by Movie List function, you can adjust an image by Energy
Saving and AV Mode key on the remote control. User setup for each image mode does not operate.
• Trick Mode does not support other functions than ►► if video files do not have index information.
• When playing video file using network, the Trick mode is limited to 2-times speed.
• Video file names that contain special characters may not be playable.
39
To use a USB device
Supported DivX file
File
Video Decoder
Audio Codec
mpg, mpeg
MPEG1, 2
MP2, MP3, Dolby Digital, LPCM
dat
MPEG1
Extension
name
ts, trp, tp
To use a USB device
40
MPEG2, H.264/AVC, VC1
Max Resolution
MP2
MP2, MP3, Dolby Digital,
AAC, HE-AAC
vob
MPEG1, 2
MP2, MP3, Dolby Digital, LPCM
mp4, mov
MPEG4, DivX 3.11, DivX 4.12, DivX 5.x,
DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02,
Xvid 1.03, Xvid 1.10-beta1/2, H.264/AVC
AAC, HE-AAC, MP3
mkv
H.264/AVC, MPEG-1,2,4
divx, avi
MPEG2, MPEG4, DivX 3.11, DivX 4.DivX
5, DivX 6, Xvid 1.00, Xvid 1.01, Xvid
1.02, Xvid 1.03, Xvid 1.10-beta1/2b
H.264/AVC
MP2, MP3, Dolby Digital,
LPCM, ADPCM, AAC, HE-AAC
Motion JPEG
(avi, mp4, mkv)
JPEG
LPCM, ADPCM
asf, wmv
VC1
WMA
flv
Sorenson H.263, H264
MP3, AAC
MP2, MP3, Dolby Digital, AAC
1920x1080@30p
HE-AAC, LPCM
(only, Motion JPEG
640x480@30p)
Screen Components
You can also adjust USB in the INPUT menu.
1
1
2
3
4
5
Select MY MEDIA.
Select Movie List.
2
1
Page 1/1
Movie List
USB1 External
Drive1
001
002
005
006
Page 1/1
003
004
4
Move
To Photo List
Play
Mark Mode
Change Numbers
P
Page Change
MARK
Mark
Exit
3
• Some files may be displayed
the preview image by icon
only.
5
• Non-supported files are
displayed the preview
image by icon only.
To use a USB device
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 1
Current page/ total pages of
contents under the folder
focused on 1
2
• Abnormal files are
displayed in the
form of bitmap.
41
To use a USB device
Movie Selection
■■When playing movie files
Page 1/1
Movie List
USB1 External
Drive1
Page 1/1
001
002
003
005
006
051. Apple_ ......
02:30:25
Move
To Photo List
To use a USB device
1
Change Numbers
Select the target folder or drive.
2
004
Play
P
Page Change
movie page.
Mark
Exit
Mark Mode
• Use the P
MARK
button to navigation in the
Select the desired movie title.
3
Movie files are played.
Using the remote control
GREEN
Repeatedly, press the GREEN button to converted to Photo List->Music List.
YELLOW
A method to view in 5 large thumbnail or simple list.
BLUE
Convert to Mark Mode.
Return to normal TV viewing.
EXIT
►
42
Press the PLAY(►) button to return to normal playback.
■■When selected movie files are played
Page 1/1
Movie List
Mark Mode
Drive1
USB1 External
001
005
Page 1/1
002
003
006
051. Apple_ ......
02:30:25
Move
Play Marked
Select the target folder or drive.
2
3
Select the desired movie title.
BLUE or
4
5
Unmark All
Mark
P
Exit Mark Mode
Page Change
MARK
Mark
Exit
• When one or more movie files are
marked, the marked movies will
be played in sequence.
Convert to Mark Mode.
To use a USB device
1
Mark All
004
Mark desired Movie file.
RED
Marked movie file is played.
NOTE
►►In the case of files not supported, a message regarding non-supported file is displayed.
43
To use a USB device
Using the remote control
RED
GREEN
Mark all movie files on the screen.
YELLOW
Deselect all marked movie files.
BLUE
Exit the Mark Mode.
EXIT
To use a USB device
44
Play the selected movie file.
Once a movie file finishes playing, the next selected one will be played automatically.
Return to normal TV viewing.
NOTE
►If
► you select “Yes” from OSD when playing the same file after the movie file has been stopped, it
will restart where it stopped previously.
►If
► continuous series files exist within the folder, the next file will automatically be played.
But, this excludes cases when the Repeat function of Movie List Option is turned “On” (Refer to
p. 47) or when set as Marked Play.
►In
► the case where files are not validated, a message will appear regarding invalid file.
Using the Movie List function, play
■■ Image shown may differ from your TV.
Choose options.
Set Video Play.
Set Video.
Set Audio.
■
2
II
►
or
01:02:30 / 02:30:25
◄◄ ►►
Q.MENU
Option
Hide
Exit
Show the Option menu.
To use a USB device
1
Close
◄►
►
Select Set Video Play., Set Video. or Set Audio.
NOTE
►►Option values changed in Movie List does not affect Photo List and Music List.
►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List
excluding Movie List.
►►When replaying the video file after stopping, you can play from where it stopped previously.
45
To use a USB device
Using the remote control
■
►
Stop the playing movie file.
Press the PLAY(►) button to return to normal playback.
During playback, press the Pause(II) button.
■■ Still screen is displayed.
■■ If no buttons are pressed on the remote control for 10 minutes after pausing, the
TV returns to the playback state.
■■ Press the Pause(II) button and then use the FF(►►) button for slow motion.
II
◄◄ / ►►
To use a USB device
When playing,
repeatedly, press the REW(◄◄) button to speed up ◄◄(x2) -> ◄◄◄(x4) ->
◄◄◄◄(x8) ->◄◄◄◄◄(x16) ->◄◄◄◄◄◄(x32) .
repeatedly, press the FF(►►) button to speed up ►►(x2)-> ►►►(x4) ->
►►►►(x8) ->►►►►►(x16) -> ►►►►►►(x32).
■■ Pressing these buttons repeatedly increases the fast forward/reverse speed.
MENU
or
BACK
Q.MENU
Show the Option menu.
Hide the menu on the full-sized screen.
■■ To see the menu again on the full-sized screen, press OK button to display.
EXIT
Return to normal TV viewing.
<>
■■ When using the < or > button during playback a cursor indicating the position can
be viewed on the screen.
Press the ENERGY SAVING button repeatedly to change the brightness of your
screen.(Refer to p.71)
Press the AV MODE button repeatedly to select the desired source.(Refer to p.33)
46
■■When you select the Set Video Play.
Set Video Play.
Picture Size
◄
Full
►
Audio Language
◄
1
►
Subtitle Language
◄
On
►
● Language
◄
English
►
● Code page
◄
Default
►
● Sync
◄
0
►
● Position
◄
0
►
● Size
◄
Normal
►
Repeat
◄
On
►
Previous
2
Make appropriate adjustments.
Subtitle Language
Support Language
Latin1
English, French, Spanish, Portuguese, Malaysia,
Indonesia
Cyrillic
Russian
Thai
Thai
Hebrew
Hebrew
Arabic
Arab, Parsi, Krudish
Unicode(UTF-16)
Vietnamese language
►Picture
►
Size : Selects your desired picture
format during movie play.
►Audio
►
Language : Changes the Language
Group of the audio during movie play. Files
with a single audio track cannot be selected.
►Subtitle
►
Language : Turn on/off the subtitle.
►Language
►
: Activated for SMI subtitle and
can select the language within the subtitle.
►Code
►
page : Can select the font for subtitle. When set to default, same font as general menu will be used.
►Sync
►
: Adjusts the time synchronisation of
the subtitle from -10 secs to +10 secs by
steps of 0.5 secs during movie play.
►Position
►
: Changes the position of the
subtitle either up or down during movie
play.
►Size
►
: Selects your desired Subtitle size
during movie play.
►Repeat
►
: Turn on/off repeat function of
movie playback. When turned on, the file
within the folder will be played back
repeatedly. Even when the repeated playback is turned off, it can run the playback if
the file name is similar to the previous file.
To use a USB device
Select Picture Size, Audio
Language, Subtitle Language
or Repeat.
1
NOTE
►►Only 10,000 of sync blocks can be supported within the subtitle file.
►►When playing a video, you can adjust the Picture Size by pressing the RATIO button.
47
To use a USB device
■■When you select the Set Video.
■■ Image shown may differ from your TV.
Set Video.
Picture Mode
◄
Standard
►
● Backlight
70
◄
● Contrast
100
◄
● Brightness
50
◄
►
● Colour
60
◄
►
►
● Dynamic Contrast
◄
● Edge Enhancer
● Noise Reduction
TruMotion
Picture Reset
Medium
►
◄
High
►
◄
Medium
►
◄
Low
►
Previous
To use a USB device
1
Select Picture Mode or TruMotion.
2
Make appropriate adjustments.
■■When you select the Set Audio.
Set Audio.
Sound Mode
◄
Standard
►
Auto Volume
◄
Off
►
Clear Voice II
◄
Off
►
Balance
0
◄
L
R ►
Previous
1
2
48
Select Sound Mode, Auto Volume, Clear Voice II or Balance.
Make appropriate adjustments.
Photo list
You can view photo files on USB storage device.
The On Screen Display may be different from your TV. Images are an example to assist with the TV operation.
When you are watching the photo by the Photo List function, you can not change the picture mode.
PHOTO(*.JPEG) supporting file
Baseline : 64 x 64 to 15360 x 8640
Progressive : 64 x 64 to 1920 x 1440
• You can play JPEG files only.
• Non-supported files are displayed in the form of predefined icon.
• An error message occurs for corrupted files or file formats that cannot be played.
• Corrupted image files may not be displayed properly.
• It may take some time to view high-resolution images in full screen.
To use a USB device
Screen Components
You can also adjust USB in the INPUT menu.
1
Select MY MEDIA.
2
Select Photo List.
2
1
1
2
3
4
5
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 1
Current page/ total pages of
contents under the folder
focused on 1
Page 1/1
Photo List
USB1 External
001
010
Drive1
002
011
Page 1/1
003
004
005
006
012
013
014
015
Move
To Music List
007
009
4
View
Mark Mode
Change Numbers
008
5
P
Page Change
MARK
Mark
Exit
3
49
To use a USB device
Photo Selection
■■When playing photo files
Page 1/1
Photo List
Drive1
USB1 External
001
010
002
011
Page 1/1
003
004
005
006
012
013
014
015
Move
To Music List
To use a USB device
1
Select the target folder or drive.
2
3
Change Numbers
008
007
View
P
Page Change
Mark Mode
• Use the P
photo page.
009
MARK
Mark
Exit
button to navigation in the
Select the desired photos.
Photo files are displayed.
Using the remote control
GREEN
Repeatedly, press the GREEN button to converted to Music List->Movie List.
YELLOW
A method to view in 5 large thumbnail or simple list.
BLUE
Convert to Mark Mode.
Return to normal TV viewing.
50
■■When selected photo files are displayed
Page 1/1
Photo List
Mark Mode
Drive1
USB1 External
001
010
002
011
Page 1/1
003
004
005
006
012
013
014
015
Move
View Marked
Select the target folder or drive.
2
3
Select the desired photos.
BLUE or
4
5
Unmark All
Convert to Mark Mode.
Mark
P
Page Change
Exit Mark Mode
009
MARK
Mark
Exit
• When one or more photos are marked, you
can view each marked photo or a slide show
of the marked photos. If no photos are
marked, you can view every individual photo
in the folder or a slide show of all photos in
the folder.
To use a USB device
1
Mark All
008
007
Mark desired photo file.
RED
Marked photo file is displayed.
Using the remote control
RED
Display the selected photo file.
GREEN
Mark all photo files on the screen.
YELLOW
Deselect all marked photo files.
BLUE
Exit the Mark Mode.
Return to normal TV viewing.
51
To use a USB device
How to view photo
Detailed operations are available on full-sized photo view screen.
Page 1/1
Photo List
Drive1
USB1 External
001
002
010
011
Page 1/1
003
004
005
006
012
013
014
015
Move
To Music List
008
007
View
P
Page Change
MARK
Mark
Exit
Mark Mode
Change Numbers
009
To use a USB device
01_a.jpg
2008/12/10
1920 x 1080
479 KB
◄
►
The aspect ratio of a photo may change the size
of the photo displayed on the screen in full size.
Press the EXIT button to move to the previous
menu screen.
◄
Slideshow
1
2
3
►
BGM
■
2/13
►
Q.MENU
Option
Select the target folder or drive.
Hide
Exit
• Use the P
photo page.
button to navigation in the
Select the desired photos.
The selected photo is displayed in full
size.
• Press the EXIT button to go back to Photo List.
• Press the BACK button to make Help OSD disappear.
52
01_a.jpg
2008/12/10
1920 x 1080
479 KB
4
◄
►
Select the
Slideshow,
BGM, � (Rotate),
/
(or
),
, Option, Hide
or Exit.
• Use
◄
Slideshow
►
BGM
■
2/13
►
Q.MENU
Option
Hide
Exit
button to select the previous
or next photo.
• Use
button to select and control
the menu on the full-sized screen.
►►BGM (Background Music) : Listen to music while viewing photos in full size.
■ Set the BGM device and album in Options before using this function.
■ You can adjust Option by Q.MENU or MENU button on the remote control.
►► � (Rotate) : Rotate photos.
■ Rotates the photo 90°, 180°, 270°, 360° clockwise.
■ It can not be rotate when the width of a picture is bigger than supported
height.
►►
►► /
To use a USB device
►►Slideshow : When no picture is selected, all photos in the current folder are displayed during slide show. If some photos are selected, those photos are displayed
in a slide show.
■ Set the time interval of the slide show in Option.
(ZOOM IN): View the photo by zoom in 2, 4 times.
: View the photo in full mode or original mode.
►►
: Press the ENERGY SAVING button repeatedly to change the brightness of your screen.(Refer to p.71)
►►Option : Set values for Slide Speed and BGM.
■ Use
button and OK button to set values. Press OK to save the
settings.
■ You cannot change BGM while BGM is playing.
■ You can only select the MP3 folder saved on the device that currently displays the photo.
►►Hide : Hide the menu on the full-sized screen.
■ To see the menu again on the full-sized screen, press OK button to display.
Press the EXIT button to go back to Photo List.
53
To use a USB device
Using the Photo List function
■■ Image shown may differ from your TV.
Choose options.
◄
►
Set Photo View.
Set Video.
Set Audio.
Close
◄
Slideshow
1
►
BGM
or
To use a USB device
2
2/13
►
Q.MENU
■
Option
Hide
Show the Option menu.
Select Set Photo View., Set Video. or Set Audio.
NOTE
►►Option values changed in Movie List does not affect Photo List and Music List.
►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List
excluding Movie List.
■■When you select the Set Photo View,
Set Photo View.
Slide Speed
◄
BGM
Fast
►
Drive1
● Repeat
◄
On
►
● Random
◄
Off
►
Previous
1
2
54
Exit
Select Slide Speed or BGM.
Make appropriate adjustments.
■■When you select the Set video,
Set Video.
Picture Mode
Vivid
◄
►
● Backlight
100
◄
►
● Contrast
95
◄
►
● Brightness
50
◄
►
● Colour
70
◄
►
● Dynamic Contrast
◄
High
►
● Edge Enhancer
◄
High
►
● Noise Reduction
◄
Medium
►
Picture Reset
2
Select Picture Mode.
Make appropriate adjustments.
■■When you select the Set Audio.
To use a USB device
1
Prev.
Set Audio.
Sound Mode
◄
Standard
►
Auto Volume
◄
Off
►
Clear Voice II
◄
Off
►
Balance
0
◄
L
R ►
Previous
1
2
Select Sound Mode, Auto Volume, Clear Voice II or Balance.
Make appropriate adjustments.
55
To use a USB device
Music list
You can play music files on USB storage device.
Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be
supported by this model.
Music file on your USB device can be played by this unit.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
MUSIC (*.MP3) supporting file
Bit rate 32 to 320
• Sampling rate MPEG1 Layer3 : 32 kHz, 44.1 kHz, 48 kHz
• Sampling rate MPEG2 Layer3 : 16 kHz, 22.05 kHz, 24 kHz
• Sampling rate MPEG2.5 Layer3 : 8 kHz, 11.025 kHz, 12 kHz
To use a USB device
Screen Components
You can also adjust USB in the INPUT menu.
1
1
2
3
4
5
6
Select MY MEDIA.
Preview: If any album jacket
for the file(Album Art Image)
exists, this jacket is displayed.
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 2
Current page/ total pages of
contents under the folder
focused on 2
2
Select Music List.
Page 1/1
Music List
USB1 External
1
001. - B01.mp3
00:00
Drive1
002. - B02.mp3
00:00
Page 1/1
003. - B03.mp3
00:00
5
Move
To Movie List
6
004. - B04.mp3
00:00
005. - B05.mp3
00:00
Change Numbers
4
56
3
2
Play
Mark Mode
P
Page Change
MARK
Exit
Mark
Music Selection
Page 1/1
Music List
USB1 External
001. - B01.mp3
00:00
Drive1
Page 1/1
002. - B02.mp3
00:00
003. - B03.mp3
00:00
004. - B04.mp3
00:00
005. - B05.mp3
00:00
Move
To Movie List
Change Numbers
■■When playing music files
Page Change
Mark Mode
MARK
Mark
Exit
• Use the P
button to navigate up/down in
the music page.
Select the target folder or drive.
2
3
P
Select the desired music title.
Music files are played.
Using the remote control
GREEN
Repeatedly, press the GREEN button to converted to Movie List->Photo List.
YELLOW
A method to view in 5 large thumbnail or simple list.
BLUE
Convert to Mark Mode.
To use a USB device
1
Play
Return to normal TV viewing.
57
To use a USB device
■■When selected music files are played
Page 1/1
Music List
Mark Mode
Drive1
001. - B01.mp3
00:00
Page 1/1
002. - B02.mp3
00:00
003. - B03.mp3
00:00
004. - B04.mp3
00:00
005. - B05.mp3
00:00
Move
Play Marked
1
To use a USB device
Select the desired music title.
BLUE or
4
5
Unmark All
Select the target folder or drive.
2
3
Mark All
Convert to Mark Mode.
Mark desired music file.
RED
Marked music file is played.
Using the remote control
RED
Display the selected music file.
GREEN
Mark all music files on the screen.
YELLOW
Deselect all marked music files.
BLUE
Exit the Mark Mode.
Return to normal TV viewing.
58
Mark
P
Page Change
Exit Mark Mode
MARK
Mark
Exit
• When one or more music files are marked,
the marked music title will be played in
sequence. For example, if you want to listen
to only one music repeatedly, just mark the
music only and play it. If no music is marked,
all the music in the folder will be played in
sequence.
• If you want to activate Random playback, you
must set Option->Set audio play.->Random
to On.
Using the Music List function, play
Page 1/1
Music List
3 file(s) Marked
Drive1
USB1 External
Page 1/1
Set Audio Play.
►
004. - B04.mp3
00:00
005. - B05.mp3
00:00
►
005. - B05.mp3
■
1
or
II ◄◄ ►►
Set Audio.
006. - B06.mp3
00:00
◄►
Play with Photo
007. - B07.mp3
00:00
008. - B08.mp3
00:00
Close
02:30 / 03:25
Q.MENU
Option
Hide
Exit
Show the Option menu.
Select Set Audio Play. or Set Audio.
NOTE
►►Option values changed in Movie List does not affect Photo List and Music List.
►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List
excluding Movie List.
►►You can listen to the music only within the device currently played.
To use a USB device
2
►
Choose options.
59
To use a USB device
Using the remote control
■
Stop the playing music file.
►
Press the PLAY(►) button to return to normal playback.
II
When you press the Pause(II) button while playing the file, the playback will be
paused.
When you press the Pause(II) button again while the playback is paused, it will
resume the playback.
◄◄ / ►►
To use a USB device
Press the ENERGY SAVING button repeatedly to change the brightness of your
screen.
Only Off/Screen Off operates from the Movie List, Photo List, Music List.
ENERGY
SAVING
or
BACK
EXIT
<>
60
Start playing the selected music files and then move to the Photo List.
GREEN
MENU
When playing,
When you press the REW(◄◄) button, the previous music file will be played.
When you press the FF(►►) button, the next music file will be played.
Q.MENU
Show the Option menu.
■■ When you press the Back button while the music is playing, the music player
currently playing will be hidden and only the music list will be displayed.
■■ When you press the Exit button while the Music player is displayed, only the
music will be stopped and the player will not return to normal TV viewing.
■■ When you press the Exit button while the music is stopped or while the music
player is hidden, the player will return to normal TV viewing.
■■ When using the < or > button during playback a cursor indicating the position can
be played.
■■When you select the Set Audio Play,
Set Audio Play.
Repeat
◄
On
►
Random
◄
Off
►
Previous
1
Select Repeat or Random.
2
Make appropriate adjustments.
Set audio.
Sound Mode
◄
Standard
►
Auto Volume
◄
Off
►
Clear Voice II
◄
Off
►
Balance
0
◄
L
To use a USB device
■■When you select the Set Audio,
R ►
Prev.
1
2
Select Sound Mode, Auto Volume, Clear Voice II or Balance.
Make appropriate adjustments.
61
To use a USB device
Using the remote control
■■ If you don't press any button for a while during the playing, the
play information box (as shown in the below) will float as a
screen saver.
■■ The ‘Screen Saver’?
Screen saver is to prevent screen pixel damage due to an
fixed image remaining on the screen for a extended period of
time.
002. B02.mp3
► 00:31 / 04:04
NOTE
To use a USB device
62
►►A damaged or corrupted music file does not play but displays 00:00 in playtime.
►►A music file downloaded from a paid service with copyright protection does not start but displays inappropriate information in playtime.
►►If you press OK, ■ buttons, screen saver is stopped.
►►The PLAY(►), Pause(II), ■ , ►►, ◄◄ buttons on the remote control are also available in this mode.
►►You can use the ►► button to select the next music file and the ◄◄ button to select the previous music
file.
DIVX® VOD guide
In order to play purchased or rented DivX® VOD contents, you should register your device with 10
digit DivX registration code from your device at www.divx.com/vod.
■■ Image shown may differ from your TV.
MY MEDIA
DivX Reg.Code
Deactivation
EzSign TV
Movie List
Press OK(
Photo List
Music List
3
Exit
Select MY MEDIA.
BLUE
Select DivX Reg. Code.
Display DivX Reg. Code.
• Press the MENU/EXIT button to return to normal TV viewing.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays
DivX video. Visit DivX.com for more information and software tools to convert your
files into DivX video.
To use a USB device
2
Close
) to see photos from the USB.
Option
1
Prev.
You must register your device to
play DivX protected videos.
Registration code : **********
Register at http://vod.divx.com
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain
your registration code, locate the DivX VOD section in your device setup menu. Go
to vod.divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation
or its subsidiaries and are used under license.
Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668;
7,515,710; 7,519,274
NOTE
►►Movie files are supported as follows
Resolution : under 1920x1080 WxH pixels
Frame rate : under 30 frames/sec(1920x1080), under 60 frames/sec(under 1280x720)
►►Video Codec : MPEG 1, MPEG 2, MPEG 4, H.264/AVC, DivX 3.11, DivX 4.12, DivX 5.x, DivX 6, Xvid 1.00,
Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1, Xvid 1.10-beta2, JPEG, VC1, Sorenson H.263/H.264.
63
To use a USB device
DIVX® VOD deregistration
You should deregister your device with 8 digit DivX deregistration code from your device at www.divx.
com/vod.
MY MEDIA
DivX Reg.Code
Deactivation
EzSign TV
Movie List
Press OK(
Photo List
To use a USB device
2
No
Exit
Select MY MEDIA.
BLUE
3
4
Yes
) to see photos from the USB.
Option
1
Previous
Music List
Deregistration code :
********
Deregister at http://vod.divx.com
Continue with registration?
Select Deactivation.
Select Yes.
Display Deactivation.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
NOTE
►►Once the deregistration is executed, you must register your device again to see DivX® VOD contents.
64
MHEG (MULTIMEDIA AND HYPERMEDIA INFORMATION
CODING EXPERT GROUP)(IN DIGITAL MODE)
(Only South Africa, Malaysia)
The TV gives you access to digital teletext which is greatly improved in various aspects such as text,
graphics etc.
This digital teletext can access special digital teletext services and specific services which broadcast
digital teletext.
Teletext within Digital Service
1
Press the numeric or P
button to select a
digital service which broadcasts digital teletext.
2
Follow the indications on digital teletext and
move onto the next step by pressing TEXT,
OK,
, RED, GREEN, YELLOW, BLUE
or NUMBER buttons and etc..
3
To change digital teletext service, select a different service by the numeric or P
button.
1
Press the numeric or P
button to select a
certain service which broadcasts digital teletext.
2
Press the TEXT or coloured button to switch on
teletext.
3
Follow the indications on digital teletext and move
onto the next step by pressing OK,
, RED,
GREEN, YELLOW, BLUE or NUMBER buttons and
so on.
4
Press the TEXT or colour button to switch off
digital teletext and return to TV viewing.
MHEG (MULTIMEDIA AND HYPERMEDIA
INFORMATION CODING EXPERT GROUP)
Teletext in Digital Service
Some services may allow you to access text services by pressing the RED button.
65
MHEG (MULTIMEDIA AND HYPERMEDIA INFORMATION
CODING EXPERT GROUP)(IN DIGITAL MODE)
(Only New Zealand)
This feature is enabled only in New Zealand.
- In New Zealand, pressing the Guide key will display MHEG EPG provided by New Zealand on the screen.
This system has an MHEG(Multimedia and hypermedia information coding expert group) to help your navigation through all the possible viewing options.
►
DTV 1 TV ONE
►
Pr. Change
► Next
Watch
Good Morning
21:00
00:00
Show/Game Show
16:9
720p
... HE-AAC
Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,
with regular and special guests.
Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,
with regular and special guests.
▼
INFO
Shows current programme information
Displayed with a TV or DTV Programme.
Displayed with a Teletext Programme.
Displayed with a Radio Programme.
Displayed with a Subtitle Programme.
Displayed with a MHEG Programme.
Displayed with a Scramble Programme.
HE-AAC Displayed with a HE-AAC Programme.
MHEG (MULTIMEDIA AND HYPERMEDIA
INFORMATION CODING EXPERT GROUP)
2
3
66
Displayed with a Dolby Digital PLUS Programme.
Aspect ratio of broadcasting programme.
576i/p, 720p, 1080i/p : Resolution of broadcasting programme
Switch on the MHEG.
Select a Programme
1
Displayed with a Dolby Digital Programme.
Aspect ratio of broadcasting programme.
Switch on MHEG
1
Up
Down
Preview the Broadcast Programme
Information.
change to desired channel.
The MHEG will disappear after
moving to a selected channel.
Button Function in Listing Mode
Select the Broadcast Programme
Information.
Select Channel.
YELLOW Change to Next Week or Prev Day.
BLUE Change to Next Day or Today.
Next Week
EPG/Guide
The MHEG will disappear after
moving to a selected channel.
19
Change to Now/Next mode.
Switch off MHEG.
INFO
Detail information on or off.
Today
Button Function in NOW/NEXT Mode
You can view a channel being broadcasted and one scheduled to follow.
Select desired channel.
1
TV ONE
The MHEG will disappear after moving
to a selected channel.
Now 2.30pm
Next 3.00pm
Neighbours
Jojo’s Circus
2
TV2
Now 2.30pm
Next 3.00pm
Neighbours
Jojo’s Circus
3
TV3
Now 2.00pm
Next 3.00pm
Oprah
Rugrats
Change to Listing mode.
4
C4
Now 2.00pm
Next 4.00pm
The Officaial NZ Top 40
Vodafone Select Live
5
Switch off MHEG.
INFO
2.33pm Tue 12 Feb
What’s on now/next.
Now 12.00am
Next 3.00pm
News : Te Kaea
Advice: Ask Your Auntie
MHEG (MULTIMEDIA AND HYPERMEDIA
INFORMATION CODING EXPERT GROUP)
EPG/Guide
Detail information on or off.
67
Picture Control
Picture Size (Aspect Ratio) Control
You can watch the screen in various picture formats; 16:9, Just Scan,
Original, Full Wide, 4:3, 14:9, Zoom and Cinema Zoom.
If a fixed image is displayed on the screen for a long time, that fixed
image may become imprinted on the screen and remain visible.
You can adjust the enlarge proportion using
button.
This function works in the following signal.
1
2
Select Aspect Ratio.
PICTURE menu.
•F
or Zoom Setting, select 14:9, Zoom and
Select the desired picture format.
picture control
• 16:9
The following selection will allow you to adjust the
picture horizontally, in linear proportion, to fill the
entire screen(useful for viewing 4:3 formatted
DVDs).
Cinema Zoom in Ratio Menu. After completing Zoom Setting, the display goes
back to Q.Menu.
• Original
When your TV receives a wide screen signal it will
automatically change to the picture format broadcast.
Original
• Just Scan
Following Selection will lead to you view the
picture of best quality without loss of original
picture in high resolution image.
Note : If there is noise in original Picture, You
can see the noise at the edge.
Just Scan
68
•Y
ou can also adjust Aspect Ratio in the
or
Original
• Full Wide (Only DTV)
When TV receives the wide screen signal, it will
lead you to adjust the picture horizontally or vertically, in a linear proportion, to fill the entire screen
fully.
4:3 and 14:9 video is supported in full screen without any video distortion through DTV input.
Full Wide
or
Full Wide
• 4:3
The following selection will allow you to view a picture with an original 4:3 aspect ratio.
• Zoom
The following selection will allow you to view
the picture without any alteration, while filling
the entire screen. However, the top and bottom
of the picture will be cropped.
• 14:9
You can view a picture format of 14:9 or a general
TV programme in the 14:9 mode. The 14:9 screen
is viewed in the same way as in 4:3, but is moved
to the up and down.
• Cinema Zoom
Choose Cinema Zoom when you want to
enlarge the picture in correct proportion.
Note:When enlarging or reducing the picture,
the image may become distorted.
picture control
◄ or ► button: Adjust enlarge proportion of
Cinema Zoom. The adjustment range is 1 to 16.
▼ or ▲ button: Move the screen.
NOTE
►►You can only select 4:3, 16:9 (Wide), 14:9, Zoom/Cinema Zoom in Component mode.
►►You can only select 4:3, Original, 16:9 (Wide), 14:9, Zoom/Cinema Zoom in HDMI mode.
►►You can only select 4:3, 16:9 (Wide) in RGB-PC, HDMI-PC mode only.
►►In DTV/HDMI/Component (over 720p) mode, Just Scan is available.
►►In DTV (over 576p) mode, Just Scan is available in Australia only.
69
piCturE Control
piCturE WizarD
this feature lets you adjust the picture quality of the original image.
use this to calibrate the screen quality by adjusting the Black and White level etc. General users can
calibrate the screen quality by easily following each stage.
When you adjust the image to low, recommended or High, you can see the changed result as an
example.
in rGB-pC/HDmi-pC/DVi-pC mode, the changed Colour, tint and H/V sharpness values are not
applied.
piCture
● aspect
ratio
move
With picture Wizard, you can adjust the picture quality of the
original image.
: 16:9
1
piCture COntrOl
2
3
4
5
mode
►
energy saving
● picture
►
● picture Wizard
●
picture Wizard
OK
: Off
: standard
• Backlight
70
• Contrast
100
• Brightness
50
• sharpness
70
previous
select piCturE.
select picture Wizard.
adjust standard(black level,
White level, tint, Colour,
Horizontal sharpness, Vertical
sharpness, backlight) or
preferred(black level, White
level, tint, Colour, sharpness,
Dynamic Contrast, Colour
temperature, backlight).
select input source to apply
the settings.
next
• if you stop the setting before the
final stage, the changes will not be
applied
• the adjustment value is saved to
Expert1.
• Once the picture Wizard sets the
image quality, the energy saving is
changed into Off.
• if the picture quality setting of
Expert1 is changed, use the
picture reset before entering the
picture Wizard to reset the picture
quality setting.
• standard : mode to set standard
picture quality.
• preferred : mode to set user preferred picture quality rather than
standard picture.
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
70
EnErgY saVing
it reduces the tV’s power consumption.
the default factory setting is adjusted to the comfortable level to be viewed at home.
You can change the brightness of your screen by adjusting the Energy saving level or by setting the
picture mode.
When adjusting energy saving in mHeG mode, the energy saving setting is applied after mHeG is
finished.
selecting ‘screen off’ while tuned to a radio station channel will reduce power consumption.
3
● picture
Wizard
piCture
OK
: 16:9
●
●
ꕊ
energy
saving: Off
energy
saving
●
picture mode
: Off
● aspect
ratio
● picture
Wizard
●
●
: standard
move
: 16:9
ꕊ energy
saving: Off
energy
saving
● picture
mode
OK
: standard
• Backlight
70
• Backlight
• Contrast
100
• Contrast
• Brightness
50
• Brightness
• sharpness
70
• sharpness
auto
:Off
Off
Off
minimum
70
medium
100
maximum
50
screen
Off
70
select piCturE.
select
Energy saving.
select auto, off, minimum , medium, maximum or screen off.
piCture COntrOl
2
ratio
►
1
move
● aspect
►
piCture
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
• When you select screen Off, the screen will be turned off in 3 seconds and screen Off will start.
• if you adjust “Energy saving-auto, maximum”, backlight feature will not work.
• You can also adjust this feature by selecting Energy saving button on the remote control.
• When selecting auto, Backlight is automatically adjusted through intelligent sensor according to the
surrounding condition when intelligent sensor is in the tV.
71
piCturE Control
prEsEt piCturE sEttings
picture mode-preset
Vivid/Family
standard
Cinema
sport/Cricket
game
strengthen the contrast, brightness, colour and sharpness for vivid picture.
the most general screen display status.
Optimizes video for watching movies.
Optimizes video for watching sports events.
Optimizes video for playing games.
■ image shown may differ from your tV.
● aspect
ratio
● picture
Wizard
●ꕊ
move
OK
: 16:9
● aspect
ratio
● picture
Wizard
●
energy saving : Off
●●picture
picture mode
mode
piCture
energy saving
●●picture
mode
picture
mode
standard
::standard
move
OK
: 16:9
: Off
standard
::standard
Vivid
70
• Backlight
70
• Contrast
100
• Contrast
100
standard
standard
►
• Backlight
►
piCture
Cinema
• Brightness
50
• Brightness
50
sport
• sharpness
70
• sharpness
70
Game
expert1
expert2
piCture COntrOl
1
2
3
select piCturE.
select picture mode.
select Vivid, standard, Cinema, sport or game.
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
• picture mode adjusts the tV for the best picture appearance. select the preset value in the
picture mode menu based on the programme category.
• When the intelligent sensor function is on, the most suitable picture is automatically adjusted
according to the surrounding conditions.
• You can also adjust picture mode in the q. menu.
72
manual piCturE aDjustmEnt
picture mode-user option
backlight
to control the brightness of the screen, adjust the brightness of lCD panel.
adjusting the backlight when setting the brightness of the set is recommended.
Contrast
adjusts the signal level between black and white in the picture. You may use Contrast when the bright
part of the picture is saturated.
brightness
adjusts the base level of the signal in the picture.
sharpness
adjusts the level of crispness in the edges between the light and dark areas of the picture.
the lower the level, the softer the image.
Colour
adjusts intensity of all colours.
tint
adjusts the balance between red and green levels.
Colour temp.
adjust to left direction to make a picture reddish or adjust to right direction to make a picture bluish.
■ image shown may differ from your tV.
● aspect
ratio
● picture
Wizard
●ꕊ
move
piCture
OK
: 16:9
energy saving : Off
●●picture
picture mode
mode
● aspect
ratio
● picture
Wizard
●
standard
::standard
energy saving
●●picture
mode
picture
mode
move
OK
: 16:9
: Off
Vivid
standard
::standard
70
• Backlight
70
• Contrast
100
• Contrast
100
50
• Brightness
50
• sharpness
70
• sharpness
70
Cinema
sport
Game
expert1
expert2
1
2
3
4
5
select piCturE.
select picture mode.
piCture COntrOl
• Brightness
standard
standard
►
• Backlight
►
piCture
select Vivid/Family, standard, Cinema, sport/Cricket or game.
select backlight, Contrast, brightness, sharpness, Colour, tint or Colour
temp..
make appropriate adjustments.
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
73
picture control
• Benefits of using Backlight
- The electricity consumption is reduced by
up to 60 %.
- The black brightness is reduced. (As the
black has greater depth, you can enjoy a
better quality definition.)
- You can adjust brightness with maintaining
original signal resolution.
NOTE
►►You cannot adjust colour, sharpness and tint in the RGB-PC/HDMI-PC mode.
►►When the Expert 1/2 is selected, you can select Backlight, Contrast, Brightness, H Sharpness, V
Sharpness, Colour or Tint.
picture control
74
PICTURE IMPROVEMENT TECHNOLOGY
You can calibrate the screen for each Picture Mode or set the video value according to the special
video screen.
You can set the video value differently for each input.
To reset to the factory default screen after making adjustments to each video mode, execute the
“Picture Reset” function for each Picture Mode.
■ Image shown may differ from your TV.
PICTURE
Move
• Sharpness
70
• Colour
60
PICTURE
OK
0
R
G
• Colour Temp.
0
W
C
►
• Advanced
Advanced Control
Control
►
• Tint
• Picture Reset
• Screen
• Screen
Move
OK
Dynamic Contrast
• Sharpness
70
Dynamic Colour
• Colour
R60
G
Clear White
• Tint
C
W0
Skin Colour
• Colour Temp.
◄ Medium
►
Medium
Off
0
Reduction
• Advanced
Control
AdvancedNoise
Control
Medium
Digital Noise Reduction
• Picture Reset
Medium
Gamma
Medium
Black Level
Auto
▼
Close
2
3
4
Select PICTURE.
Select Advanced Control.
Select your desired Source.:
Dynamic Contrast, Dynamic Colour, Clear White, Skin Colour, Noise Reduction,
Digital Noise Reduction, Gamma, Black Level, Eye Care, Real Cinema, Colour
Gamut or xvYCC. (Refer to p. 77 to 78)
PICTURE CONTROL
1
Make appropriate adjustments.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
75
piCturE Control
ExpErt piCturE Control
By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they
see fit, offering the optimal picture quality for users.
this may also be used to help a professional optimize the tV performance using specific videos.
■ image shown may differ from your tV.
piCture
ratio
● picture
Wizard
●
energy saving
mode
picture
mode
●●picture
piCture
OK
::
expert1
standard
OK
◄ medium
standard
Cinema
• Backlight
70
sport
• Contrast
90
Game
• Brightness
50
expert1
expert1
• H sharpness 70
expert2
• trumotion
►
• screen
►
medium
• V sharpness
Digital noise 60
reduction
Vivid
: Off
move
Dynamic Contrast
• H sharpness
70
noise reduction
: 16:9
►
● aspect
move
medium
• Colour
60 r
Black level
• tint
0
real Cinema
advanced
Control
•• expert
Control
Colour Gamut
• picture reset
: Off edge enhancer
G
auto
On
eBu
High
xvYCC
auto
expert pattern
Off
▼
Close
1
piCture COntrOl
2
3
4
5
6
select piCturE.
select picture mode.
select
Expert1 or
Expert2.
select Expert Control.
select your desired source.
make appropriate adjustments.
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
76
*This feature is not available for all models.
Dynamic Contrast
(Off/Low/Medium/High)
Dynamic Colour
(Off/Low/High )
■■ Adjusts the contrast to keep it at the best level according to the brightness of
the screen. The picture is improved by making bright parts brighter and dark
parts darker.
■■ Adjusts screen colours so that they look livelier, richer and clearer. This feature enhances hue, saturation and luminance so that red, blue, green and
white look more vivid.
Skin Color
■■ Adjusts skin colour of the picture so that user can set his favourite skin
colour.
(-5~5)
Noise Reduction
(Off/Low/Medium/High/ ■■ Reduces screen noise without compromising video quality.
Auto(In Analogue Mode
Only))
Digital Noise Reduction
■■ Reduces noise regarding MPEG compressed video.
(Low/Medium/High/Off)
Gamma
(Advanced Control:
Low/Medium/High
Expert Control:
1.9/2.2/2.4 )
• Low : The picture of the screen gets darker.
• High : The picture of the screen gets brighter.
• Auto : Sets black level of the screen to High or Low automatically according to
the input signal level.
■■ Set black level of the screen to proper level.
■■ This function enables to select 'Low' or 'High' in the following mode:
AV(NTSC-M), HDMI or Component. Otherwise, 'Black level' is set to 'Auto'.
Clear White
(Off/Low/High)
■■ Makes the white area of the screen brighter and clearer.
Eye Care
(Low/High/Off)
*This feature is not available for all models.
■■ Adjusts the brightness of the screen automatically to the best level for
eyes when the screen is too bright.
■■ This feature is disable in “Picture Mode-Vivid, Cinema.
Real Cinema
(On/Off)
picture control
Black Level
(Low/High/Auto)
■■ You can adjust brightness of dark area and middle gray level area of the picture.
• Low/1.9 : Makes dark and middle gray level area of the picture brighter.
• Medium/2.2 : Expresses original picture levels.
• High/2.4: Make dark and middle gray level area of the picture darker.
■■ You can watch a cinema-like video by eliminating judder effect.
■■ Use this function when you watch film-originated movie contents.
77
picture control
Colour Gamut
(Advanced Control:
Wide/Standard)
• Standard : Mode to use original colour area regardless of the display
characteristics.
• Wide: Mode to use maximum colour area of the TV display.
■■ Maximize the utilization for colour area that can be expressed.
• Standard : Mode to use original colour area regardless of the display
characteristics.
Color Gamut
• Wide : Mode to use maximum colour area of the TV display.
(Expert Control:
Standard/EBU/
• EBU : Mode to display EBU colour area.
SMPTE/BT709/Wide) • SMPTE : Mode to display SMPTE colour area.
• BT709 : Mode to display BT709 colour area.
Edge Enhancer
■■ Makes the edge of the picture clearer and distinctive.
(Off/Low/High)
■■ This function can use in “Picture Mode-Expert.”
*This feature is not available for all models.
xvYCC
■■ This is the function to express richer colour.
(Auto/off/on)
■■ This function is enabled in "Picture mode - Cinema, Expert" when xvYCC
signal is inputted through HDMI
Expert Pattern
■■ This is the pattern necessary for checking the picture of Digital TV.
(Off/Pattern1/Pattern2) ■■ This function is enabled in "Picture Mode - Expert" when you watch DTV.
Colour Filter
■■ This is the function to filter the specific colours of the video.
(Off/Red/Green/Blue) You can use the RGB filter to set colour saturation and hue accurately.
picture control
Colour Temperature
(Medium/Warm/Cool)
Colour Management
System
78
This is the function to adjust the overall colour of the screen to the feeling you
want.
a. • Method : 2 Points
• Pattern: Inner, Outer
• Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 ~ +50.
b. • Method : 10 point IRE
• Pattern: Inner / Outer
• IRE (Institute of Radio Engineers) is the unit to display the size of the video
signal and can be set among 10, 20, 30 - 100. You can adjust Red, Green or
Blue according to each setting.
• Luminance: This function displays calculated luminance value for 2.2 gamma.
You can input luminance value you want at 100 IRE, than the target luminance
value for 2.2 gamma is displayed at every 10 steps from 10 IRE to 90 IRE.
• Red/Green/Blue: The adjustment range is -50 ~ +50.
■■ As the tool used by the experts to make adjustments by using the test
patterns, this does not affect other colours but can be used to selectively
adjust the 6 colour areas (Red/Green/Blue/Cyan/Magenta/Yellow).
Colour difference may not be distinctive even when you make the adjustments for the general video.
■■ Adjusts Red/Green/Blue/Yellow/Cyan/Magenta.
• Red/Green/Blue/Yellow/Cyan, Magenta Colour : The adjustment
range is -30 ~ +30.
• Red/Green/Blue/Yellow/Cyan/Magenta Tint : The adjustment
range is -30 ~ +30.
■■ This feature is disable in RGB-PC and HDMI (PC) mode.
piCturE rEsEt
settings of the selected picture modes return to the default factory settings.
piCture
move
• sharpness
70
• Colour
60
piCture
OK
• tint
0
r
G
• Colour temp.
0
W
C
1
3
4
60
OK
►
• advanced Control
Yes
no
• screen
select piCturE.
piCture COntrOl
2
• Colour
•• picture
picture reset
reset
►
• screen
70
• tint ? all picture
0 rsetting willGbe reset.
C
• Colour temp.
Continue?W
• advanced Control
•• picture
picture reset
reset
move
• sharpness
select picture reset.
select Yes.
initialize the adjusted value.
• press the mEnu/Exit button to return to normal tV viewing.
• press the baCk button to move to the previous menu screen.
79
picture control
Power Indicator
Adjust the power/standby indicator light on the front of the TV.
Standby Light
Determines whether to set the indicator light on the front of the TV to On or Off in standby mode.
Power Light
Determines whether to set the indicator light on the front of the TV to On or Off when the power turns
on.
OPTION
Move
● Language(Language)
● Country
● Country
: Australia
of Hearing (ꔞ): Off
● Factory
● Set
● IR
picture control
3
4
Setting
Blaster
►
● Factory
:1
● Set
: Home Use
● Mode
: Off
● IR
Setting
Blaster
Standby Light
◄
Power Light
Reset
ID
OK
: Australia
of Hearing (ꔞ): Off
● Power Indicator
Reset
ID
● Mode
● Hard
►
● Power Indicator
2
Move
● Language(Language)
● Hard
1
OPTION
OK
On
►
On
:1
: Home Use
Close
: Off
Select OPTION.
Select Power Indicator.
Select Standby Light or Power Light.
Select your desired Source.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
80
Sound & Language control
Auto Volume Leveler
Auto Volume automatically remains on the same level of volume if you change programmes.
Because each broadcasting station has its own signal conditions, volume adjustment may be needed
every time the channel is changed. This feature allows users to enjoy stable volume levels by making
automatic adjustments for each programme.
If sound quality or volume is not at the level you want, it is recommended to use a separate home theater system or amp to cope with different user environments.
AUDIO
Move
● Clear
Voice II
: Off
3
● Balance
● Sound
1
2
3
Mode
AUDIO
OK
: Off
● Auto
● Clear
0
L
: Standard
R
Move
Volume
Voice II
: Off
● Balance
● Sound
Mode
OK
MHEG
Off
: Off
3
►
Volume
►
● Auto
On
0
L
R
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
Select AUDIO.
Select Auto Volume.
sound & language control
Select On or Off.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
81
sound & language control
Clear Voice II
By differentiating the human sound range from others, it helps users listen to human voices better.
AUDIO
Volume
: Off
Off
:: Off
● Balance
● Sound
1
2
sound & language control
3
Mode
● Auto
33
►
Clear Voice
Voice II
II
●●Clear
AUDIO
OK
►
● Auto
Move
0
L
R
: Standard
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
Select AUDIO.
Move
Volume
Clear Voice
Voice II
II
●●Clear
: Off
Off
:: Off
● Sound
Mode
● Clear
33
● Balance
OK
L
0 ● Level
Voice II
R
◄
3
Off
-
: Standard
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
Close
• If you select “On” for Clear Voice II,
Infinite Sound feature will not work.
• Select levels from ‘-6’ to ’+6’.
Select Clear Voice II.
Select On or Off.
Adjustment for Clear Voice Level With selecting On
4
5
Select Level.
Make desired adjustment.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
82
►
+
Preset Sound Settings-Sound Mode
You can select your preferred sound setting; Standard, Music, Cinema, Sport/Cricket or Game and
you can also adjust the Treble, Bass.
Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content.
Standard, Music, Cinema, Sport/Cricket and Game are preset for optimum sound quality at the factory.
Standard Offers standard-quality sound.
Music Optimizes sound for listening to music.
Cinema Optimizes sound for watching movies.
Sport/CricketOptimizes sound for watching sports events.
Game Optimizes sound for playing games.
■■ Image shown may differ from your TV.
AUDIO
Move
Volume
● Clear
Voice II
: Off
Volume
● Clear
0
L
R
Voice II
Move
OK
: Off
: Off
3
L
Standard
0 Standard
● Balance
Standard
:: Standard
• Infinite Sound : Off
• Treble
50
• Infinite Sound : OffCinema
• Treble
50 Sport
• Bass
50
• Bass
• Reset
• Reset
Select AUDIO.
R
Music
Sound Mode
Mode
●●Sound
50 Game
• You can also adjust Sound Mode in the Q.
Menu.
Select Sound Mode.
Select Standard, Music, Cinema, Sport/Cricket or Game.
sound & language control
3
Standard
:: Standard
3
►
2
Sound Mode
Mode
●●Sound
● Auto
►
● Balance
1
AUDIO
OK
: Off
►
● Auto
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
83
sound & language control
Sound Setting Adjustment -User Mode
■■ Image shown may differ from your TV.
AUDIO
Move
Volume
● Clear
Voice II
: Off
● Auto
3
4
5
sound & language control
84
Sound Mode
Mode
●●Sound
Standard(User)
:: Standard
L
R
Voice II
Move
OK
: Off
: Off
3
L
R
Standard(User)
0 Standard
● Balance
►
3
0
Music
Sound Mode
Mode
●●Sound
Standard(User)
:: Standard
• Infinite Sound : Off
• Treble
50
• Infinite Sound : OffCinema
• Treble
50 Sport
• Bass
50
• Bass
• Reset
• Reset
►
2
Volume
● Clear
● Balance
1
AUDIO
OK
: Off
►
● Auto
50 Game
Select AUDIO.
Select Sound Mode.
Select Standard, Music, Cinema, Sport/Cricket or Game.
Select Treble or Bass.
Set the desired sound level.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
Infinite Sound
Select this option to sound realistic.
1
2
3
Select AUDIO.
Select Infinite Sound.
Select On or Off.
Infinite Sound : Infinite Sound is a patented
LG proprietary sound processing technology
that strives immersive 5.1 surround sound
impression with front two loudspeakers.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
Balance
You can adjust the sound balance of the speakers to preferred levels.
AUDIO
Move
Volume
● Clear
Voice II
: Off
1
2
3
● Clear
0 0L
R
Move
Volume
Voice II
: Off
●● Balance
Balance
Mode
OK
: Off
3
0●0LBalance
: Standard
● Sound
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
R
0◄
L
R
►
Close
Select AUDIO.
Select Balance.
Make desired adjustment.
sound & language control
3
Mode
● Auto
►
●● Balance
Balance
● Sound
AUDIO
OK
: Off
►
● Auto
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
85
sound & language control
TV Speakers On/ Off Setup
You can adjust the TV internal speaker status.
In AV, COMPONENT, RGB and HDMI with HDMI to DVI cable, the TV speaker can be operational
even when there is no video signal.
If you wish to use an external Hi-Fi system, turn off the TV’s internal speakers.
● Sound
Move
Mode
● Sound
Move
Mode
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
: PCM
● Digital Audio
: :On
On
●●TV
TVSpeaker
Speaker
Out
1
Setting : Auto
►
● DTV Audio
►
• Infinite Sound : Off
●●TV
TVSpeaker
Speaker
● DTV Audio
Out
OK
: Standard
● Digital Audio
: PCM
: :On
On
Setting : Auto
Off
On
PCM
Select AUDIO.
2
Select TV Speaker.
3
sound & language control
86
AUDIO
OK
: Standard
Select On or Off.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
NOTE
►►Some menus in AUDIO are disabled when TV Speaker is set to Off.
►
AUDIO
DTV Audio Setting (in digital mode only)
(Only DTV)
When different audio types exist in an input signal, this function allows you to select the audio type
you want.
AUDIO
● Sound
Move
Mode
AUDIO
OK
: Standard
● Sound
Move
Mode
OK
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
• Bass
50
• Bass
50
• Reset
• Reset
Auto
Auto
: PCM
● Digital Audio
: PCM
HE-AAC
: On
● TV
: On
Dolby Digital+
: :Auto
Auto
Dolby Digital
● TV
Out
Speaker
DTVAudio
AudioSetting
Setting
●●DTV
Auto
: :Auto
Out
Speaker
● DTV Audio Setting
50
►
● Digital Audio
►
MPEG
1
2
Select DTV Audio Setting.
Select Auto, HE-AAC, Dolby Digital +, Dolby
Digital or MPEG.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
•Auto: Automatically outputs in the order HE-AAC > Dolby Digital+ > Dolby Digital > MPEG.
•HE-AAC, Dolby Digital +, Dolby Digital, MPEG: Allows users to select the audio type they want.
ex) If MPEG is selected, MPEG is always outputted.
If MPEG is not supported, another audio type is set in that order.
sound & language control
3
Select AUDIO.
87
sound & language control
Selecting Digital Audio out
It is possible to use in DTV, HDMI, DivX mode.
This function allows you to select your preferred Digital Audio Output.
When Dolby Digital is available, selecting Auto in the Digital Audio Out menu will set SPDIF(Sony
Philips Digital InterFace) output to Dolby Digital.
If Auto is selected in the digital audio out menu when Dolby Digital is not available, SPDIF output will
be PCM(Pulse-code modulation).
Even if both Dolby Digital and Audio language have been set in a channel which broadcast Dolby
Digital Audio, only Dolby Digital will be played.
Move
Mode
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
● TV
Speaker
● DTV Audio
1
sound & language control
2
3
Out
AUDIO
: :PCM
PCM
● Sound
Move
Mode
: On
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
● TV
Setting : Auto
Out
Speaker
● DTV Audio
OK
: Standard
● Digital Audio
►
● Digital Audio
OK
: Standard
►
● Sound
Auto
: :PCM
PCM
PCM
PCM
: On
Setting : Auto
Select AUDIO.
Select Digital Audio Out.
Select Auto or PCM.
Item
Audio Input
Digital Audio output
Auto(Speaker On)
MPEG
Dolby Digital
Dolby Digital Plus
HE-AAC
PCM
Dolby Digital
Dolby Digital
PCM
Auto(Speaker Off)
MPEG
Dolby Digital
Dolby Digital Plus
HE-AAC
PCM
Dolby Digital
Dolby Digital
Dolby Digital
All
PCM
PCM
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
88
►
AUDIO
Audio Reset
Settings of the selected Sound Mode return to the default factory settings.
AUDIO
Mode
: Standard
● Sound
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
• Bass
50
• Bass
• Reset
• Reset
Speaker
● DTV Audio
4
Mode
● Digital Audio
: On
● TV
Setting : Auto
: Standard
?
: PCM
Speaker
● DTV Audio
Out
OK
: PCM
: On
Setting : Auto
50
50
All audio settings will be resetted.
Continue?
Yes
No
Select AUDIO.
Select Reset.
Select Yes.
sound & language control
3
Out
►
● TV
2
Move
● Digital Audio
1
AUDIO
OK
►
● Sound
Move
Initialize the adjusted value.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
89
sound & language control
I/II
Stereo/Dual Reception (In Analogue Mode Only)
When a programme is selected, the sound information for the station appears with the programme
number and station name.
1
2
Select Audio or Audio Language.
Select the sound output.
Broadcast
On Screen Display
Mono
MONO
Stereo
STEREO
Dual (Except for Singapore, New Zealand and
Indonesia)
NICAM (Only Singapore, New Zealand and Indonesia)
DUAL I, DUAL II, DUAL I+II (Except for Singapore, New Zealand
and Indonesia)
NICAM (Only Singapore, New Zealand and Indonesia)
sound & language control
■■ Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved.
■■ Language selection for dual language broadcast (Except for Singapore, New Zealand and
Indonesia)
If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL
II or DUAL I+II.
DUAL ISends the primary broadcast language to the loudspeakers.
DUAL IISends the secondary broadcast language to the loudspeakers.
DUAL I+IISends a separate language to each loudspeaker.
90
NICAM Reception (In Analogue Mode Only)
(Except for Singapore, New Zealand and Indonesia)
If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous
Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of broadcast received.
1
When NICAM mono is received, you can select NICAM MONO or FM MONO.
2
When NICAM stereo is received, you can select NICAM STEREO or FM MONO.
If the stereo signal is weak, switch to FM MONO.
3
When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II or
NICAM DUAL I+II or FM MONO.
In AV, Component, RGB and HDMI mode, you can select output sound for the left and right
loudspeakers.
Select the sound output.
L+R: Audio signal from audio L input is sent to the left loudspeaker and audio signal from
audio R input is sent to the right loudspeaker.
L+L: Audio signal from audio L input is sent to left and right loudspeakers.
R+R: Audio signal from audio R input is sent to left and right loudspeakers.
sound & language control
Speaker Sound Output Selection
91
sound & language control
On-Screen Menu Language / Country
Selection
The installation guide menu appears on the TV screen when it is switched on for the first time.
1
Select your desired language. (Except for Australia, New Zealand, Singapore and
South Africa.)
2
Select your country. (Only Australia & New Zealand)
* If you want to change Language/ Country selection
1
2
Select Language(Language).
3
Select Menu Language. (Except
for Australia, New Zealand,
Singapore and South Africa.)
4
5
sound & language control
92
1
Select OPTION.
Select your desired language.
Select OPTION.
2
Select Country(Only
Australia & New
Zealand).
3
4
Select your country.
Save.
Save.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
NOTE
►►If you do not finish the set-up Installation Guide by pressing BACK or if you time out on the OSD (On
Screen Display) the installation menu will continuously appear until the set up is completed whenever the
TV is switched on.
►►If you select the wrong local country, teletext may not appear correctly on the screen and some problems
may occur during teletext operation.
►►DTV mode control buttons may not function based on country broadcasting circumstances. (Only DTV)
►►In country that Digital broadcasting regulation isn’t fixed, some DTV function may not work depending on
digital broadcasting circumstances. (Only DTV)
Language Selection (In digital mode only)
(Only DTV)
The Audio function allows selection of a preferred language.
If audio data in a selected language is not broadcast, the default language audio will be played.
Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a
selected language is not broadcast, the default language subtitle will be displayed.
When the languages you selected as the primary for Audio Language and Subtitle Language and Text
Language are not supported, you can select language in secondary category (Only New Zealand).
In Digital mode, use the Text language function when two or more Text languages are broadcast. If teletext data in a selected language is not broadcast, the default Text language will be displayed.
1
2
Select Language(Language).
3
4
Select Audio Language or Subtitle
Language or Text Language.
Select your desired language.
Save.
Select OPTION.
2
Select Hard of Hearing(
3
).
Select On or Off.
NOTE
►► It is only available to use Hard of Hearing
on some TV stations in New Zealand.
• Press the BACK button to move to the previous menu screen.
sound & language control
5
1
Select OPTION.
93
sound & language control
Audio Language OSD Information
< Audio Language Selection >
►►When two or more audio languages are broadcast, you can
select the audio language.
Display
N.A
Status
Not Available
MPEG Audio
Dolby Digital Audio
Audio for “Visual Impaired”
1
2
Select Audio or Audio
Language.
Audio for “Hearing Impaired”
Dolby Digital Plus Audio
HE-AAC
HE-AAC Audio
Select an audio language.
< Subtitle Language Selection >
►►When two or more subtitle languages are broadcast, you
can select the subtitle language with the SUBTITLE button
on the remote control.
►►Press the
button to select a subtitle language.
Subtitle Language OSD Information
Display
N.A
Status
Not Available
Teletext Subtitle
Subtitle for “Hard of Hearing”
-The audio/subtitles can be displayed in a simpler form with 1 to 3 characters broadcast by the
service provider.
- When you select supplementary Audio (Audio for “Visual/Hearing Impaired”) the TV may output
a part of the Main audio.
sound & language control
94
Analogue
TV
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under license from Dolby Laboratories. “Dolby “and
the double-D symbol are trademarks of Dolby Laboratories.
Digital TV
• There is a possibility that when HDMI mode, some DVD players do not
make SPDIF sound. At that time, set the output of the digital audio of the
DVD player to PCM. (In HDMI, Dolby Digital Plus is not supported).
Time Setting
Clock Setup
The clock is set automatically when receiving a digital signal in Auto mode. You can set the clock
manually in Manual mode.
You must set the time correctly before using on/off timer function.
< Only Australia >
When you select a Time Zone city, the TV time is set by the time offset information based on Time
Zone and GMT (Greenwich Mean Time) which is received with the broadcast signal and the time is
set automatically by a digital signal.
<Only Indonesia, Israel>
GMT (Greenwich Mean Time) which is received with the broadcast signal and the time is set automatically by a digital signal.
Time Zone is activated only in Auto Mode.
■■ Image shown may differ from your TV.
TIME
Move
TIME
OK
►
● Clock
Move OK OK
◄Move
● Clock
Date
►
Auto
● Off
Time
: Off
● Off
Time
: Off
Month
Mar.
● On
Time
: Off
● On
Time
: Off
● Sleep
: Off
Year
: Off
Hour
2008
● Sleep
Timer
Timer
Only DTV
3
16
Minute
09
Time Zone
NSW/ACT
GMT+10.0
Close
Only Australia, Indonesia and Israel
2
3
4
5
Select TIME.
Select Clock.
Select Auto or Manual. (Only DTV)
time setting
1
Select either the year, month, date, time or Time Zone(Only Australia, Indonesia and
Israel) option.
Set the year, month, date, time or Time Zone (Only Australia, Indonesia and Israel)
option.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
95
time setting
Auto on/off time setting
The Off time function automatically switches the TV to standby at a preset time.
Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed.
The Off time function overrides the On time function if both are set to the same time.
The TV must be in standby mode for the On time to work.
TIME
Move
TIME
OK
● Clock
● Clock
Time
: Off
● Off
● On Time
: Off
● On Time
● Sleep
: Off
►
Timer
►
● Off
Move
Time
● Sleep
Timer
OK
1 Mar 2007 16:09
: Off
Repeat
◄
Off
: Off
Hour
00
: Off
Minute
00
Input
►
Antenna
Programme
TV1
Volume
30
Close
1
2
3
time setting
4
5
6
•T
o cancel On/Off Time function, select Off.
Select TIME.
•F
or On Time function only
Select Off Time or On Time.
2
Select Repeat.
Select Off, Once, Daily, Mon. ~ Fri.,
Mon. ~ Sat., Sat. ~ Sun. or Sun..
Set the hour.
1
3
4
Select Input.
Select the input source.
Set the programme.
Adjust volume level at switch-on.
Set the minutes.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
96
Sleep Timer setting
You do not have to remember to switch the TV off before you go to sleep.
The sleep timer automatically switches the TV to standby after the preset time has elapsed.
1
2
Select Sleep Timer.
Select Off, 10, 20, 30, 60, 90, 120, 180 or 240 min.
•W
hen you switch the TV off, the preset sleep timer is cancelled.
•Y
ou can also adjust Sleep Timer in the TIME menu.
time setting
97
Parental Control / Ratings
Set Password & Lock System
Enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset.
If a channel is locked, enter the password to unlock it temporarily.
● Set
: :Off
Off
● Block
● Parental
● Input
3
parental control /
ratings
4
5
Lock
►
● Lock System
►
2
OK
LOCK
● Set
● Key
1
Move
Password
Programme
Guidance: Blocking Off
Block
: Off
OK
Off
● Lock System
: :Off
Off
● Block
● Parental
● Input
● Key
Select LOCK.
Move
Password
Lock
Programme
On
Teletext
►
LOCK
Guidance: Blocking Off
Block
: Off
• If you forget your password, press ‘0’, ‘3’,
‘2’, ‘5’ on the remote control handset.
Select Lock System.
Select On.
Set the password.
Input a 4-digit password.
Be sure to remember this number!
Re-enter new password for confirm.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
98
Block Programme
Blocks any programme that you do not want to watch or that you do not want your children to watch.
It is available to use this function in Lock System ”On”.
Enter a password to watch a blocked programme.
■■ Image shown may differ from your TV.
Programme Edit
LOCK
● Set
Move
System
: On
● Block
● Parental
● Input
● Key
Lock
Programme
▲
▼
Page 1/1
C
RADIO
DTV
OK
Password
● Lock
Favourite Group :
TV
1 Nine Digital
2 Nine Digital HD
3 Nine Guide
4 7 Digital
5 7 HD Digital
6 7 Digital 1
7 7 Digital2
8 7 Digital3
9 7 Guide
Guidance: Blocking Off
Block
: Off
Pr. Change
Navigation
P
Page Change
Previous
Block/Unblock
1
Select LOCK.
2
3
5
Select Block Programme.
Enter the Block Programme.
YELLOW
Select a programme to be locked.
parental control /
ratings
4
Select Lock System.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
99
parental control / ratings
Parental Control (In Digital Mode only)
(Only DTV)
This function operates according to information from the broadcasting station. Therefore if the signal
has incorrect information, this function does not operate.
A password is required to gain access to this menu.
This set is programmed to remember which option it was last set to even if you switch the set off.
Prevents children from watching certain adult’s TV programmes, according to the ratings limit set.
Enter a password to watch a blocked programme.
Rating differs by country.
■■ Image shown may differ from your TV.
LOCK
● Set
Move
Password
● Lock
System
● Set
: On
● Block
●● Parental
Parental Guidance
Guidance:: Blocking
Blocking Off
Off
● Input
● Key
Lock
Programme
▲
▼
Block
: Off
Move
OK
programmes
Password
● Lock
Blocking Off : Permits all
LOCK
OK
System
● Block
●● Parental
Parental Guidance
Guidance:: Blocking
Blocking Off
Off
● Input
Lock
: Off
Programme
G
● Key
▲
Block All
: On
Block
PG
M
▲
▼
MA
AV
R
Blocking Off
1
2
3
parental control /
ratings
4
Select LOCK.
Select Lock System.
Select Parental Guidance.
Make appropriate adjustments.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
100
External Input Blocking
Enables you to block an input.
It is available to use this function in Lock System ”On”.
■■ Image shown may differ from your TV.
LOCK
● Set
Move
Password
● Lock
System
● Set
: On
● Block
● Parental
● Input
Lock
Programme
Guidance: Blocking Off
Block
▲
Move
System
: On
● Block
● Parental
▼
: Off
● Key
OK
Password
● Lock
● Key
LOCK
OK
Lock
Programme
● AV1
Guidance: Blocking Off
● AV2 ▲
● Input Block
▼
● Component
: Off
◄
Off
►
Off
Off
● RGB
Off
● HDMI1
Off
● HDMI2
Off
Close
1
2
3
5
Select Lock System.
Select Input Block.
parental control /
ratings
4
Select LOCK.
Select input source.
Select On or Off.
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
101
parental control / ratings
Key Lock
This feature can be used to prevent unauthorized viewing by locking out the front panel controls, so
that it can only be used with the remote control.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
LOCK
Password
● Lock
System
3
: Off
● Lock
● Block
Programme
● Parental
● Input
Guidance: Blocking Off
Block
: Off: Off
Select LOCK.
Select Key Lock.
Select On or Off.
Move
OK
Password
System
: Off
● Block
● Parental
● Input
● Key Lock
Programme
Guidance: Blocking Off
Block
Off
: :Off
MHEG
Off
►
2
● Set
● Key
Lock
● Key
Lock
1
LOCK
OK
►
● Set
Move
On
• In Key Lock ‘On’, if the TV is turned off, press the
/ I, INPUT, P
button on the TV or POWER
or NUMBER buttons on the remote
INPUT, P
control then the set will be turned on.
• With the Key Lock On, the display ‘
Key
Lock On ’ appears on the screen if any button on
the front panel is pressed while viewing the TV.
• When another OSD is displayed, ‘
Key Lock
On ’ will not operate.
parental control /
ratings
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
102
Teletext
This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives up-to-theminute information on news, weather, television programmes, share prices and
many other topics.
The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT
systems. SIMPLE (standard teletext) consists of a number of pages which are
selected by directly entering the corresponding page number. TOP and
FASTEXT are more modern methods allowing quick and easy selection of
teletext information.
Switch on/off
Press the TEXT button to switch to teletext. The initial page or last page
viewed appears on the screen.
Two page numbers, TV station name, date and time are displayed on the
screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The previous mode reappears.
SIMPLE Text
■■ Page selection
Enter
1
the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the
correct page number.
The P
button can be used to select the preceding or following page.
2
teletext
103
teletext
TOP Text
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow
field denotes the next group and the blue field indicates the next block.
■■ Block / group / page selection
1 With the blue button you can progress from block to block.
2
Use
the yellow button to proceed to the next group with automatic overflow to the next block.
3 With the green button you can proceed to the next existing page with automatic overflow to the next
group.
button can be used.
4 Alternatively the P
The red button returns to the previous selection. Alternatively the P button can be used.
■■ Direct page selection
As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using
the NUMBER buttons in TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing the
corresponding coloured button.
■■Page selection
1
2
3
teletext
104
4
Press the T.OPT button and then use
button to select
menu. Display the index page.
You can select the pages which are colour coded along the bottom line with corresponding
coloured buttons.
AS with SIMPLE teletext mode, you can select a page by entering its three digit page number with
the NUMBER buttons in FASTEXT mode.
The P
button can be used to select the preceding or following page.
Special Teletext Functions
Press the T. OPT button and then use
button to select the Text Option menu.
Text Option
■■Index
Select the each index page.
Index
Time
Hold
Reveal
■■Time
Update
Close
When viewing a TV programme, select this menu to display the time at the top right
hand corner of the screen.
In the teletext mode, press this button to select a sub page number. The sub page number is displayed at
the bottom of the screen. To hold or change the sub page, press the RED/GREEN,< > or NUMBER buttons.
■■ Hold
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages.
The number of sub pages and the sub page displayed is, usually, shown on the screen below the
time. When this menu is selected the stop symbol is displayed at the top left-hand corner of the
screen and the automatic page change is inactive.
■■Reveal
Select this menu to display concealed information, such as solutions to riddles or puzzles.
■■Update
Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at
the top left hand corner of the screen. When the updated page is available then display will change to
the page number. Select this menu again to view the updated teletext page.
teletext
105
Appendix
Troubleshooting
The TV does not operate properly.
The remote control
does not work
■■ Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control
directly at the TV.
■■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■■ Install new batteries.
■■ Is the sleep timer set?
Power is suddenly
■■ Check the power control settings. Has the Power supply been interrupted.
turned off
■■ If the TV is switched on and there is no input signal, it will switch off automatically after 15 minutes.
The video function does not work.
■■ Check whether the TV is switched on.
■■ Try another channel. The problem may be with the broadcast.
No picture & No sound ■■ Is the power cord inserted correctly into the mains?
■■ Check your antenna direction and/or location.
■■ Test the mains outlet by plugging another TV into the same outlet.
Picture appears slowly ■■ This is normal, the image is muted during the TV startup process. Please contact
your service centre, if the picture has not appeared after five minutes.
after switching on
■■ Adjust Colour in menu option.
No or poor colour
or poor picture
■■ Allow a sufficient distance between the TV and the VCR.
■■ Try another channel. The problem may be with the broadcast.
■■ Are the video cables installed properly?
■■ Activate any function to restore the brightness of the picture.
Horizontal/vertical bars
or picture shaking
Poor reception on
some channels
Lines or streaks
appendix
106
in pictures
No picture
when connecting
HDMI
■■ Check for local interference such as an electrical appliance or power tool.
■■ Station or cable channel experiencing problems, tune to another station.
■■ Station signal is weak, reposition the antenna to receive weaker stations.
■■ Check for sources of possible interference.
■■ Check antenna (Change the position of the antenna).
■■ Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are
not High Speed HDMI Cable, flickering or no screen display can result. Please
use the High Speed HDMI Cable.
The audio function does not work.
Picture OK & No
sound
No output from one
of the speakers
Unusual sound from
inside the TV
No sound when connecting HDMI or USB
■■ Press the
+ or - button.
■■ Sound muted? Press MUTE button.
■■ Try another channel. The problem may be with the broadcast.
■■ Are the audio cables installed properly?
■■ Adjust Balance in menu option.
■■ A change in ambient humidity or temperature may result in an unusual noise
when the TV is switched on or off and does not indicate a fault with the TV.
■■ Check HDMI cable is High Speed HDMI Cable.
■■ Check USB cable over version 2.0.
*This feature is not available for all models.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of
range
(Invalid format)
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
Screen colour is
unstable or single
colour
■■ Adjust resolution, horizontal frequency, or vertical frequency.
■■ Check the input source.
■■ Use Auto configure or adjust clock, phase, or H/V position. (Option)
■■ Check the signal cable.
■■ Reinstall the PC video card.
appendix
107
appendix
Maintenance
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV.
Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1
A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is
almost dry, and then use it to wipe the screen.
2
Ensure there is no excess water on the screen. Allow any water or dampness to evaporate
before switching on.
Cleaning the Cabinet
■■ To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■■ Do not to use a wet cloth.
Extended Absence
CAUTION
►►If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to
protect against possible damage from lightning or power surges.
appendix
108
Product Specifications
32LD4**
37LD4**
32LD462B-TA
37LD462B-TA
799.0 mm x 555.0 mm x 207.0 mm
916.0 mm x 625.0 mm x 261.0 mm
without stand
799.0 mm x 516 mm x 73.5 mm
916.0 mm x 584 mm x 77.4 mm
with stand
without stand
9.6 kg
8.6 kg
12.9 kg
11.2 kg
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
42LD4**
47LD4**
42LD462B-TA
47LD462B-TA
1023.0 mm x 685.0 mm x 261.0 mm
1136.0 mm x 757.0 mm x 270.0 mm
without stand
1023.0 mm x 644 mm x 76.6 mm
1136.0 mm x 706 mm x 76.5 mm
with stand
without stand
15.4 kg
13.7 kg
19.6 kg
17.6 kg
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
MODELS
Dimensions
with stand
(Width x Height x
Depth)
Weight
Power requirement
MODELS
Dimensions
(Width x Height x
Depth)
Weight
with stand
Power requirement
Operating
Temperature
Environment condition
Supported movie files
Operating Humidity
0 °C to 40 °C
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Refer to p.42 to 43
■■ The specifications shown above may be changed without prior notice for quality improvement.
appendix
109
appendix
New Zealand, Singapore
Television System
Digital TV
Analogue TV
DVB-T
PAL/SECAM-B/G/D/K, PAL-I
BG : VHF/UHF 1 to 69, CATV 01 to 47
Program Coverage
UHF 21 to 69
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
Australia
Television System
Program Coverage
Indonesia, Israel
Television System
DVB-T
VHF 06 to 12,
UHF 27 to 69
DVB-T
PAL B/B
B/B : VHF/UHF 0 to 75, CATV : 2 to 44
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
Program Coverage
UHF 21 to 69
Television System
DVB-T
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
South Africa
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
Program Coverage
VHF 4 to 11, 13
UHF 21 to 68
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
Veitnam, Malaysia
Television System
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
Program Coverage
VHF 6 to 12,
I : VHF/UHF 1 to 69, CATV 01 to 47
UHF 21 to 69
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
Iran
Television System
DVB-T
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
Program Coverage
VHF 5 to 12,
I : VHF/UHF 1 to 69, CATV 01 to 47
UHF 21 to 69
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
Analogue model
Television System
-
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
Program Coverage
-
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
External Antenna
Impedance
appendix
110
75 Ω
75 Ω
■■ The specifications shown above may be changed without prior notice for quality improvement.
IR Codes
This feature is not available for all models.
Code (Hexa)
Function
Note
95
Energy Saving
R/C BUTTON
08
POWER
R/C BUTTON(POWER ON/OFF)
0B
INPUT
R/C BUTTON
79
RATIO
R/C BUTTON
F0
TV/RAD
R/C BUTTON
45
Q.MENU
R/C BUTTON
43
MENU
R/C BUTTON
AB
GUIDE
R/C BUTTON
40
Up (ꕌ)
R/C BUTTON
41
Down (ꕍ)
R/C BUTTON
07
Left (<)
R/C BUTTON
06
Right (>)
R/C BUTTON
44
OK(ꔉ)
R/C BUTTON
28
BACK
R/C BUTTON
5B
EXIT
R/C BUTTON
AA
INFO i
R/C BUTTON
30
AV MODE
R/C BUTTON
02
+
R/C BUTTON
03
-
R/C BUTTON
1E
FAV/MARK
R/C BUTTON
09
MUTE
R/C BUTTON
00
P ꕌ / PAGE ꕌ
R/C BUTTON
01
P ꕍ /PAGE ꕍ
R/C BUTTON
Number Key 0~9
R/C BUTTON
53
LIST
R/C BUTTON
1A
Q.VIEW
R/C BUTTON
72
RED Key
R/C BUTTON
71
GREEN Key
R/C BUTTON
63
YELLOW Key
R/C BUTTON
61
BLUE Key/(L/R SELECT)
R/C BUTTON
20
TEXT
R/C BUTTON
21
T.OPT(T.Option)
R/C BUTTON
39
SUBTITLE
R/C BUTTON
10~19
TV
R/C BUTTON
▀
R/C BUTTON
B0
►
R/C BUTTON
BA
ll
R/C BUTTON
8F
◄◄
R/C BUTTON
8E
►►
R/C BUTTON
0C
PORTAL
R/C BUTTON
appendix
0F
B1
111
appendix
External Control Device Setup
RS-232C Setup
H/P
IN 3
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an
A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied
with the product.
AV IN2
Type of Connector; D-Sub 9-Pin Male
No.
1
2
3
4
5
6
7
8
9
Pin Name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
1
5
6
9
RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
appendix
112
3-Wire Configurations(Not standard)
PCTV
PCTV
RXD TXD
GND
DTR
DSR
RTS
CTS
RXD TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
D-Sub 9
3TXD
2RXD
5
GND
6
DSR
4
DTR
8
CTS
7RTS
D-Sub 9
2
3
5
4
6
7
8
D-Sub 9
3TXD
2RXD
5
GND
6
DTR
4
DSR
7RTS
8
CTS
D-Sub 9
Set ID
Use this function to specify a set ID number.
OPTION
● Country
: Australia
of Hearing (ꔞ): Off
● Hard
Indicator
● Mode
: Home Use
Setting
►
::11
: Australia
Indicator
● Factory
● Set ID
OK
of Hearing (ꔞ): Off
● Power
Reset
►
● Factory
3
Move
● Country
● Power
2
OPTION
OK
● Language(Language)
● Hard
1
Move
● Language(Language)
Reset
◄
● Set ID
::11
● Mode
: Home Use
Setting
1
►
Close
Select OPTION.
Select Set ID.
Adjust Set ID to choose the desired TV ID number.
The adjustment range of SET ID is 1 to 99.
appendix
• Press the BACK button to move to the previous menu screen.
113
appendix
Communication Parameters
■■ Baud rate : 9600 bps (UART)
■■ Data length : 8 bits
■■ Parity : None
■■ Stop bit : 1 bit
■■ Communication code : ASCII code
■■ Use a crossed (reverse) cable.
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
Command Reference List
COMMAND COMMAND 1
2
appendix
114
DATA
(Hexadecimal)
01. Power k
a
00 to 01
02. Aspect Ratio
k
c
Refer to p. 115
03. Screen Mute
k
d
Refer to p. 115
04. Volume Mute
k
e
00 to 01
05. Volume Control
k
f
00 to 64
06. Contrast
k
g
00 to 64
07. Brightness
k
h
00 to 64
08. Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 64
11. OSD Select
k
l
00 to 01
00 to 01
12. Remote control lock mode
k
m
13. Treble k
r
00 to 64
14. Bass
k
s
00 to 64
15. Balance
k
t
00 to 64
16. Colour Temperature
x
u
00 to 64
17. Energy Saving
j
q
00 to 05
18. Auto Configuration
j
u
01
19. Tune Command
m
a
Refer to p. 117
20. Programme Add/Skip
m
b
00 to 01
21. Key
m
c
Key Code
22. Control Back Light
m
g
00 to 64
23. Input select (Main)
x
b
Refer to p. 118
* [Command 1] : First command to control the TV.
(j, k, m or x)
* [Command 2] : Second command to control the TV.
* [Set ID] : You can adjust the set ID to choose
desired monitor ID number in option
menu. Adjustment range is 1 to 99.
When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99)
on menu and as Hexa decimal (0x1 to
0x63) on transmission/receiving protocol.
[DATA] : To
transmit command data.
* Transmit ‘FF’ data to read status of command.
* [Cr] : Carriage Return
ASCII code ‘0x0D’
* [ ] : ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based
on this format when receiving normal data. At this
time, if the data is data read mode, it indicates
present status data. If the data is data write mode,
it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* Note : During USB operations such as DivX or EMF, all * The set transmits ACK (acknowledgement) based
commands except Power(ka) and Key(mc) are not exe- on this format when receiving abnormal data from
non-viable functions or communication errors.
cuted and treated as NG.
Data00: Illegal Code
01. Power (Command: k a)
►► To control Power On/Off of the set.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data00 : Power Off
Ack
01 : Power On
[a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack
[e][ ][Set ID][ ][OK/NG][Data][x]
[k][a][ ][Set ID][ ][FF][Cr]
05. Volume Control (Command: k f)
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data
based on this format, Acknowledgement data feed
back presents status about each function.
* OK Ack., Error Ack. and other message may display on the screen when TV is power On.
02. Aspect Ratio (Command: k c) (Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen (16:9)
04 : Zoom
06 : Original
Ack
04. Volume Mute (Command: k e)
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
[c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz /
60 Hz, 1080p 24 Hz / 30 Hz / 50 Hz / 60 Hz),
Component( 720p, 1080i, 1080p 50 Hz / 60 Hz)
mode, Just Scan is available.
* Full Wide is supported only for DTV mode.
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Transmission
Ack
[d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
[k][f][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[h][ ][Set ID][ ][OK/NG][Data][x]
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[i][ ][Set ID][ ][OK/NG][Data][x]
appendix
[k][d][ ][Set ID][ ][Data][Cr]
Data00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
►► To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Transmission
115
appendix
09. Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
13. Treble (Command: k r)
Transmission
►► To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
[k][r][ ][Set ID][ ][Data][Cr]
DataRed : 00 to Green : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
[j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[k][ ][Set ID][ ][OK/NG][Data][x]
Ack
[r][ ][Set ID][ ][OK/NG][Data][x]
14. Bass (Command: k s)
►► To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[s][ ][Set ID][ ][OK/NG][Data][x]
15. Balance (Command: k t)
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling remotely.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
Ack
01 : OSD on
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[t][ ][Set ID][ ][OK/NG][Data][x]
[l][ ][Set ID][ ][OK/NG][Data][x]
16. Colour Temperature (Command: x u)
12. Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and
remote control.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data00 : Lock off
Ack
appendix
116
01 : Lock on
[m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is on/off, external control lock is
released.
* In the standby mode, if key lock is on, TV will not
turn on by power on key of IR & Local Key.
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Transmission
[x][u][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping 1’. See page 118.
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
17. Energy Saving (Command: j q)
19.Tune Command (Command: m a)
►► To reduce the power consumption of the TV. You can
also adjust Energy Saving in PICTURE menu.
Transmission
►► Select channel to following physical number.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data00 :High channel data
Data01 :Low channel data
ex.No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 :0x00 : Analogue Main
0x10 : DTV Main
0x20 : Radio
Power Saving
Function
7
6
5
4
0
0
0
0
0
0
0
0
0
0
0
0
0
Level
Description
3
2
1
0
Low Power
0
0
0
0
Off
0
Low Power
0
0
0
1
Minimum
0
Low Power
0
0
1
0
Medium
0
Low Power
0
0
1
1
Maximum
0
0
0
0
Low Power
0
1
0
0
Auto
0
0
0
0
Low Power
0
1
0
1
Screen Off
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
Except for 32/37/42/47LD4**
DataMin: 00 to Max: 7DH
Ack
[q][ ][Set ID][ ][OK/NG][Data][x]
20. Programme Add/Skip(Command: m b)
►► To set skip status for the current Programme.
Transmission
[m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip 01 : Add
Ack
18. Auto Configure(Command: j u)
[b][ ][Set ID][ ][OK/NG][Data][x]
►► To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data01: To set
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
appendix
117
appendix
21. Key(Command: m c)
►► To send IR remote key code.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
DataKey code - Refer to page 111.
Ack
[c][ ][Set ID][ ][OK/NG][Data][x]
23. Input select (Command: x b)
(Main Picture Input)
►► To select input source for main picture.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
DataStructure
0
22. Control Back Light (Command: m g)
►► To Control the back light.
Transmission
[m][g][ ][Set ID][ ][Data][Cr]
Data: data Min: 00 to Max: 64
Ack
[g][ ][Set ID][ ][OK/NG][Data][x]
LSB
MSB
0
0
0
A :
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E : Step 110
appendix
118
73 :
74 :
Step 115
Step 116
CF : Step 199
FE : Step 254
FF : Step 255
0
0
External Input
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
* Real data mapping 1
00 : Step 0
0
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
0
Open Source Software Notice
The following GPL executables and LGPL, MPL libraries used in this product are subject to the
GPL2.0/LGPL2.1/MPL1.1 License Agreements:
GPL EXECUTABLES:
• Linux kernel 2.6, busybox, e2fsprogs, gdbserver, jfsutils, mtd-utils, procps, u-boot, udhcpc
LGPL LIBRARIES:
• cairo, directFB, gettext, glib, glibc, iconv, pixman
MPL LIBRARIES:
• Nanox
LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of
performing such distribution, such as the cost of media, shipping and handling upon e-mail request
to LG Electronics at: opensource@lge.com
This offer is valid for a period of three (3) years from the date of the distribution of this product by
LG Electronics.
You can obtain a copy of the GPL, LGPL and MPL licenses on the CD-ROM provided with this product. Also you can obtain the translation of GPL, LGPL licenses from http://www.gnu.org/licenses/oldlicenses/gpl-2.0-translations.html, http://www.gnu.org/licenses/old-licenses/lgpl-2.1-translations.html.
appendix
This product includes
• expat:
■■ copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper
■■ copyright © 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
• freetype: copyright © 2003 The FreeType Project (www.freetype.org).
• ICU: copyright © 1995-2008 International Business Machines Corporation and others
• libcurl: copyright © 1996 - 2008, Daniel Stenberg.
• libjpeg: This software is based in part on the work of the Independent JPEG Group copyright ©
1991 – 1998, Thomas G. Lane.
• libmng: copyright © 2000-2007 Gerard Juyn, Glenn Randers-Pehrson
• libpng: copyright © 1998-2008 Glenn Randers-Pehrson
• md5: copyright © 1991-2, RSA Data Security, Inc
• md5 checksum : copyright © 1999, 2000, 2002 Aladdin Enterprises
• ncurses: copyright © 1998 Free Software Foundation, Inc.
• openSSL:
■■ cryptographic software written by Eric Young.
■■ software written by Tim Hudson.
■■ software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.
openssl.org)
• strace :
■■ copyright © 1991, 1992 Paul Kranenburg.
■■ copyright © 1993 Branko Lankester.
■■ copyright © 1993 Ulrich Pegelow.
■■ copyright © 1995, 1996 Michael Elizabeth Chastain.
119
appendix
■■ copyright © 1993, 1994, 1995, 1996 Rick Sladkey.
■■ copyright © 1998-2003 Wichert Akkerman.
■■ copyright © 2002-2008 Roland McGrath.
■■ copyright © 2003-2008 Dmitry V. Levin.
■■ copyright © 2007-2008 Jan Kratochvil.
• tinyxml: copyright © 2000-2006 Lee Thomason
• xyssl: Copyright (C) 2009 Paul Bakker
• zlib: copyright © 1995-2005 Jean-loup Gailly and Mark Adler
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and
associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or
sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
OTHER DEALINGS IN THE SOFTWARE.
appendix
120
Open source license
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public License is intended to guarantee your freedom to share and change free
software--to make sure the software is free for all its users. This General Public License applies to most of the Free
Software Foundation's software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to
make sure that you have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software,
or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show
them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so that any problems introduced by others will not
reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors
of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we
have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
The act of running the Program is not restricted, and the output from the Program
is covered only if its contents constitute a work based on the Program (independent of having been made by running
the Program). Whether that is true depends on what the Program does.
appendix
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it
may be distributed under the terms of this General Public License. The "Program", below, refers to any such program
or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that
is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is
addressed as "you".
121
appendix
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of
any warranty; and give any other recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program,
and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all
of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any
change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the
Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this
License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may
redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception:
if the Program itself is interactive but does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on
the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable
form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under
the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a complete machine-readable copy of the corresponding
source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
appendix
122
The source code for a work means the preferred form of the work for making modifications to it. For an executable
work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary
form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place counts as distribution of the source code, even though
third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.
Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate
your rights under this License. However, parties who have received copies, or rights, from you under this License will
not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not
accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a
license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You
may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible
for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you
may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the
Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it
and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution
system, which is implemented by public license practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to
time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems
or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which
applies to it and "any later version", you have the option of following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If the Program does not specify a version number of
this License, you may choose any version ever published by the Free Software Foundation.
appendix
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different,
write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to
the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals
of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software
generally.
123
appendix
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve
this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to
where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public
License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later
version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General
Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the
Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO
WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain
conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
Of course, the commands you use may be called something other than `show w' and `show c'; they could even be
mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer"
for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker.
appendix
124
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a
subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is
what you want to do, use the GNU Lesser General Public License instead of this License.
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the
software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically
libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest
you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in
any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you
wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of
it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the
library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the
rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code
with the library, you must provide complete object files to the recipients, so that they can relink them with the library
after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the recipients should know that what they have is not the original
version, so that the original author's reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a
company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.
Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom
of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is
legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore
permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits
more lax criteria for linking other code with the library.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the
ordinary General Public License. It also provides other free software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain special circumstances.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use
a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
appendix
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library,
so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more
frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to
gain by limiting the free library to free software only, so we use the Lesser General Public License.
125
appendix
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a
program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from
the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the
copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public
License (also called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been distributed under these terms. A
"work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work
containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into
another language. (Hereinafter, translation is included without limitation in the term "modification".)
"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete
source code means all the source code for all modules it contains, plus any associated interface definition files, plus
the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
The act of running a program using the Library is not restricted, and output from such a program is covered only if its
contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether
that is true depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection
in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library,
and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all
of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of
any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this
License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program
that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good
faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates,
and performs whatever part of its purpose remains meaningful.
appendix
126
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of
the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function
must be optional: if the application does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Library, and can be reasonably considered independent and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the
Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy
of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU
General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU
General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other
change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License
applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding
machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent
access to copy the source code from the same place satisfies the requirement to distribute the source code, even
though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being
compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of
the Library, and therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library
(because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the
work may be a derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library.
The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and
small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it
is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under
Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of
Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with
the Library itself.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library
to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that
the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its
use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one of these things:
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at
run time a copy of the library already present on the user's computer system, rather than copying library functions
into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as
long as the modified version is interface-compatible with the version that the work was made with.
appendix
a) Accompany the work with the complete corresponding machine-readable source code for the Library including
whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object
code and/or source code, so that the user can modify the Library and then relink to produce a modified executable
containing the modified Library. (It is understood that the user who changes the contents of definitions files in the
Library will not necessarily be able to recompile the application to use the modified definitions.)
127
appendix
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials
specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to
copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the "work that uses the Library" must include any data and utility programs
needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need
not include anything that is normally distributed (in either source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies
the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in
an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with
other library facilities not covered by this License, and distribute such a combined library, provided that the separate
distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that
you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and
explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this
License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept
this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your
acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or
works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a
license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.
You are not responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you
may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the
Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and
this License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
appendix
128
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution
system which is implemented by public license practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from
time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which
applies to it and "any later version", you have the option of following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If the Library does not specify a license version number,
you may choose any version ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible
with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation,
write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two
goals of preserving the free status of all derivatives of our free software and of promoting the sharing
and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO
THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it
free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or,
alternatively, under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file
to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer
to where the full notice is found.
<one line to give the library's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General
Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any
later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public
License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the
Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by
James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
appendix
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer"
for the library, if necessary. Here is a sample; alter the names:
129
appendix
MOZILLA PUBLIC LICENSE
Version 1.1
--------------1. Definitions.
1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party.
1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications.
1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor,
and the Modifications made by that particular Contributor.
1.3. "Covered Code" means the Original Code or Modifications or the combination of the Original Code and
Modifications, in each case including portions thereof.
1.4. "Electronic Distribution Mechanism" means a mechanism generally accepted in the software development community for the electronic transfer of data.
1.5. "Executable" means Covered Code in any form other than Source Code.
1.6. "Initial Developer" means the individual or entity identified as the Initial Developer in the Source Code notice
required by Exhibit A.
1.7. "Larger Work" means a work which combines Covered Code or portions thereof with code not governed by the
terms of this License.
1.8. "License" means this document.
1.8.1. "Licensable" means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein.
1.9. "Modifications" means any addition to or deletion from the substance or structure of either the Original Code or
any previous Modifications. When Covered Code is released as a series of files, a Modification is:
A. Any addition to or deletion from the contents of a file containing Original Code or previous Modifications.
B. Any new file that contains any part of the Original Code or previous Modifications.
1.10. "Original Code" means Source Code of computer software code which is described in the Source Code notice
required by Exhibit A as Original Code, and which, at the time of its release under this License is not already
Covered Code governed by this License.
1.10.1. "Patent Claims" means any patent claim(s), now owned or hereafter acquired, including without limitation,
method, process, and apparatus claims, in any patent Licensable by grantor.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all
modules it contains, plus any associated interface definition files, scripts used to control compilation and installation
of an Executable, or source code differential comparisons against either the Original Code or another well known,
available Covered Code of the Contributor's choice. The Source Code can be in a compressed or archival form,
provided the appropriate decompression or de-archiving software is widely available for no charge.
1.12. "You" (or "Your") means an individual or a legal entity exercising rights under, and complying with all of the
terms of, this License or a future version of this License issued under Section 6.1.
For legal entities, "You" includes any entity which controls, is controlled by, or is under common control with You.
For purposes of this definition, "control" means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
appendix
130
2. Source Code License.
2.1. The Initial Developer Grant.
The Initial Developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims:
(a) under intellectual property rights (other than patent or trademark) Licensable by Initial Developer to use,
reproduce, modify, display, perform, sublicense and distribute the Original Code (or portions thereof) with or
without Modifications, and/or as part of a Larger Work; and
(b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use,
practice, sell, and offer for sale, and/or otherwise dispose of the Original Code (or portions thereof).
(c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes
Original Code under the terms of this License.
(d) Notwithstanding Section 2.1(b) above, no patent license is granted: 1) for code that You delete from the
Original Code; 2) separate from the Original Code; or 3) for infringements caused by: i) the modification of the
Original Code or ii) the combination of the Original Code with other software or devices.
2.2. Contributor Grant.
Subject to third party intellectual property claims, each Contributor hereby grants You a world-wide, royalty-free,
non-exclusive license
(a) under intellectual property rights (other than patent or trademark) Licensable by Contributor, to use, reproduce, modify, display, perform, sublicense and distribute the Modifications created by such Contributor (or portions thereof) either on an unmodified basis, with other Modifications, as Covered Code and/or as part of a
Larger Work; and
(b) under Patent Claims infringed by the making, using, or selling of Modifications made by that Contributor
either alone and/or in combination with its Contributor Version (or portions of such combination), to make, use,
sell, offer for sale, have made, and/or otherwise dispose of: 1) Modifications made by that Contributor (or portions
thereof); and 2) the combination of Modifications made by that Contributor with its Contributor Version (or portions of such combination).
(c) the licenses granted in Sections 2.2(a) and 2.2(b) are effective on the date Contributor first makes
Commercial Use of the Covered Code.
(d) Notwithstanding Section 2.2(b) above, no patent license is granted: 1) for any code that Contributor has deleted from the Contributor Version; 2) separate from the Contributor Version; 3) for infringements caused by: i)
third party modifications of Contributor Version or ii) the combination of Modifications made by that Contributor
with other software (except as part of the Contributor Version) or other devices; or 4) under Patent Claims
infringed by Covered Code in the absence of Modifications made by that Contributor.
3. Distribution Obligations.
3.1. Application of License.
The Modifications which You create or to which You contribute are governed by the terms of this License, including
without limitation Section 2.2. The Source Code version of Covered Code may be distributed only under the terms of
this License or a future version of this License released under Section 6.1, and You must include a copy of this
License with every copy of the Source Code You distribute. You may not offer or impose any terms on any Source
Code version that alters or restricts the applicable version of this License or the recipients' rights hereunder.
However, You may include an additional document offering the additional rights described in Section 3.5.
3.2. Availability of Source Code.
Any Modification which You create or to which You contribute must be made available in Source Code form under
the terms of this License either on the same media as an Executable version or via an accepted Electronic
Distribution Mechanism to anyone to whom you made an Executable version available; and if made available via
Electronic Distribution Mechanism, must remain available for at least twelve (12) months after the date it initially
became available, or at least six (6) months after a subsequent version of that particular Modification has been
made available to such recipients. You are responsible for ensuring that the Source Code version remains available
even if the
Electronic Distribution Mechanism is maintained by a third party.
3.3. Description of Modifications.
You must cause all Covered Code to which You contribute to contain a file documenting the changes You made to
create that Covered Code and the date of any change. You must include a prominent statement that the Modification
is derived, directly or indirectly, from Original Code provided by the Initial Developer and including the name of the
Initial Developer in (a) the Source Code, and (b) in any notice in an Executable version or related documentation in
which You describe the origin or ownership of the Covered Code.
appendix
3.4. Intellectual Property Matters
(a) Third Party Claims.
If Contributor has knowledge that a license under a third party's intellectual property rights is required to exercise
the rights granted by such Contributor under Sections 2.1 or 2.2, Contributor must include a text file with the
Source Code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient
detail that a recipient will know whom to contact. If Contributor obtains such knowledge after the Modification is
made available as described in Section 3.2, Contributor shall promptly modify the LEGAL file in all copies
Contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or
newsgroups) reasonably calculated to inform those who received the Covered Code that new knowledge has
been obtained.
131
appendix
(b) Contributor APIs.
If Contributor's Modifications include an application programming interface and Contributor has knowledge of
patent licenses which are reasonably necessary to implement that API, Contributor must also include this information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to Section 3.4(a) above, Contributor believes that
Contributor's Modifications are Contributor's original creation(s) and/or Contributor has sufficient rights to grant
the rights conveyed by this License.
3.5. Required Notices.
You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a
particular Source Code file due to its structure, then You must include such notice in a location (such as a relevant
directory) where a user would be likely to look for such a notice. If You created one or more Modification(s)
You may add your name as a Contributor to the notice described in Exhibit A. You must also duplicate this License
in any documentation for the Source Code where You describe recipients' rights or ownership rights relating to
Covered Code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations
to one or more recipients of Covered Code. However, You may do so only on Your own behalf, and not on behalf of
the Initial
Developer or any Contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by You alone, and You hereby agree to indemnify the Initial Developer and every Contributor
for any liability incurred by the Initial Developer or such Contributor as a result of warranty, support, indemnity or liability terms You offer.
3.6. Distribution of Executable Versions.
You may distribute Covered Code in Executable form only if the requirements of Section 3.1-3.5 have been met for
that Covered Code, and if You include a notice stating that the Source Code version of the Covered Code is available under the terms of this License, including a description of how and where You have fulfilled the obligations of
Section 3.2. The notice must be conspicuously included in any notice in an Executable version, related documentation or collateral in which You describe recipients' rights relating to the Covered Code. You may distribute the
Executable version of Covered Code or ownership rights under a license of Your choice, which may contain terms
different from this License, provided that You are in compliance with the terms of this License and that the license
for the Executable version does not attempt to limit or alter the recipient's rights in the Source Code version from
the rights set forth in this
License. If You distribute the Executable version under a different license You must make it absolutely clear that any
terms which differ from this License are offered by You alone, not by the Initial Developer or any Contributor. You
hereby agree to indemnify the Initial Developer and every Contributor for any liability incurred by the Initial
Developer or such Contributor as a result of any such terms You offer.
3.7. Larger Works.
You may create a Larger Work by combining Covered Code with other code not governed by the terms of this
License and distribute the Larger Work as a single product. In such a case, You must make sure the requirements
of this License are fulfilled for the Covered Code.
4. Inability to Comply Due to Statute or Regulation.
If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered
Code due to statute, judicial order, or regulation then You must: (a) comply with the terms of this License to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in
the LEGAL file described in Section 3.4 and must be included with all distributions of the Source Code. Except to
the
extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary
skill to be able to understand it.
5. Application of this License.
This License applies to code to which the Initial Developer has attached the notice in Exhibit A and to related
Covered Code.
6. Versions of the License.
appendix
132
6.1. New Versions.
Netscape Communications Corporation ("Netscape") may publish revised and/or new versions of the License from
time to time. Each version will be given a distinguishing version number.
6.2. Effect of New Versions.
Once Covered Code has been published under a particular version of the License, You may always continue to use
it under the terms of that version. You may also choose to use such Covered Code under the terms of any subsequent version of the License published by Netscape. No one other than Netscape has the right to modify the terms
applicable to Covered Code created under this License.
6.3. Derivative Works.
If You create or use a modified version of this License (which you may only do in order to apply it to code which is
not already Covered Code governed by this License), You must (a) rename Your license so that the phrases
"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in
your license (except to note that your license differs from this License) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public License and Netscape Public License. (Filling
in the name of the Initial Developer, Original Code or Contributor in the notice described in Exhibit A shall not of
themselves be deemed to be modifications of this License.)
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN "AS IS" BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE
COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NONINFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH
YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL
DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR
OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE.
NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1. This License and the rights granted hereunder will terminate automatically if You fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the Covered
Code which are properly granted shall survive any termination of this License. Provisions which, by their nature,
must remain in effect beyond the termination of this License shall survive.
8.2. If You initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against
Initial Developer or a Contributor (the Initial Developer or Contributor against whom You file such action is referred
to as "Participant") alleging that:
(a) such Participant's Contributor Version directly or indirectly infringes any patent, then any and all rights granted
by such Participant to You under Sections 2.1 and/or 2.2 of this License shall, upon 60 days notice from Participant
terminate prospectively, unless if within 60 days after receipt of notice You either: (i) agree in writing to pay
Participant a mutually agreeable reasonable royalty for Your past and future use of Modifications made by such
Participant, or (ii) withdraw Your litigation claim with respect to the Contributor Version against such Participant. If
within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by
the parties or the litigation claim is not withdrawn, the rights granted by Participant to You under Sections 2.1 and/or
2.2 automatically terminate at the expiration of the 60 day notice period specified above.
(b) any software, hardware, or device, other than such Participant's Contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by such Participant under Sections 2.1(b) and 2.2(b) are
revoked effective as of the date You first made, used, sold, distributed, or had made, Modifications made by that
Participant.
8.3. If You assert a patent infringement claim against Participant alleging that such Participant's Contributor Version
directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the
initiation of patent infringement litigation, then the reasonable value of the licenses granted by such Participant
under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license.
8.4. In the event of termination under Sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by You or any distributor hereunder prior to termination shall
survive termination.
9. LIMITATION OF LIABILITY.
appendix
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING
NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER
CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES,
BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF
ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR
LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.
THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY
RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH
LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
133
appendix
10. U.S. GOVERNMENT END USERS.
The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
"commercial computer software" and "commercial computer software documentation," as such terms are used in 48
C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June
1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein.
11. MISCELLANEOUS.
This License represents the complete agreement concerning subject matter hereof. If any provision of this License
is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This
License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise),
excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity
chartered or registered to do business in the United States of America, any litigation relating to this License shall be
subject to the jurisdiction of the Federal Courts of the Northern District of California, with venue lying in Santa Clara
County, California, with the losing party responsible for costs, including without limitation, court costs and reasonable
attorneys' fees and expenses. The application of the United Nations Convention on Contracts for the International Sale
of Goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed
against the drafter shall not apply to this License.
12. RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and
Contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.
13. MULTIPLE-LICENSED CODE.
Initial Developer may designate portions of the Covered Code as "Multiple-Licensed". "Multiple-Licensed" means
that the Initial Developer permits you to utilize portions of the Covered Code under Your choice of the NPL or the alternative licenses, if any, specified by the Initial Developer in the file described in Exhibit A.
EXHIBIT A -Mozilla Public License.
``The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this
file except in compliance with the License. You may obtain a copy of the License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND,
either express or implied. See the License for the specific language governing rights and limitations under the License.
The Original Code is ______________________________________.
The Initial Developer of the Original Code is ________________________.
Portions created by ______________________ are Copyright (C) ______
_______________________. All Rights Reserved.
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in
which case the provisions of [______] License are applicable instead of those above. If you wish to allow use of your
version of this file only under the terms of the [____] License and not to allow others to use your version of this file
under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other
provisions required by the [___] License. If you do not delete the provisions above, a recipient may use your version of
this file under either the MPL or the [___] License."
appendix
134
[NOTE: The text of this Exhibit A may differ slightly from the text of the notices in the Source Code files of the
Original Code. You should use the text of this Exhibit A rather than the text found in the Original Code Source Code for
Your Modifications.]
NOTE
ENG
Some video codecs listed in the manual may not be
supported, depending on the region (country).
POR
Alguns codecs de vídeo listados no manual podem não
ser suportados, dependendo da região (país).
POL
Niektóre kodeki wideo wymienione w instrukcji mogą
nie być obsługiwane, w zależności od regionu (kraju).
SPA
Algunos códecs de vídeo que figuran en el manual
pueden no ser compatibles, dependiendo de la región
(país).
THA
appendix
appendix
138
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
Model :
Serial No. :
(Only DTV)
Trade Mark of the DVB Digital Video
Broadcasting Project (1991 to 1996)
Download PDF