LG | 32LY755H | LG 32LY755H Owner’s Manual

OWNER’S MANUAL
LED TV*
* Disclaimer
LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
LY75**
LY96**
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3LICENSES
33MAINTENANCE
3
Open source software
notice information
33
33
33
4
Safety instRUctions
4
- Viewing 3D Imaging (Only 3D models)
6
INSTALLATION PROCEDURE
7
ASSEMBLING AND PREPARING
7Unpacking
11
Separate purchase
12
Parts and Button
13
- Using the Joystick button
14
Lifting and Moving the TV
15
Setting up the TV
15
- Attaching the Stand
18
Mounting on a table
20
Mounting on a wall
22
Tidying cables
24MAKING CONNECTIONS
24
25
26
26
26
27
27
27
28
29
29
30
30
Antenna Connection
HDMI Connection
MHL Connection
Audio Connection
- Digital Optical Audio Connection
Speaker Output Setup
Network Setup
- Wired network Connection
Component Connection
Composite Connection
RGB-PC Connection
Headphone Connection
USB Connection
31
REMOTE CONTROL
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
34TROUBLESHOOTING
35SPECIFICATIONS
44
IR CODES
45
EXTERNAL CONTROL DEVICE
SETUP
45
45
45
46
46
47
RS-232C Setup
Type of Connector: D-Sub 9-Pin Male
RS-232C Configurations
Communication Parameters
Command Reference List
Transmission / Receiving Protocol
WARNING
yy If you ignore the warning message, you
may be seriously injured or there is a
possibility of accident or death.
CAUTION
yy If you ignore the caution message, you
may be slightly injured or the product may
be damaged.
NOTE
yy The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE INFORMATION
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries.
This DivX Certified® device has passed rigorous testing to ensure it plays
DivX® video.
To play purchased DivX movies, first register your device at vod.divx.com.
Find your registration code in the DivX VOD section of your device setup
menu.
DivX Certified® to play DivX® video up to HD 1080p, including premium
content.
DivX®, DivX Certified® and associated logos are trademarks of DivX, LLC and
are used under license.
Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274.
For DTS patents, see http://patents.dts.com. Manufactured under license
from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol
together are registered trademarks, and DTS 2.0+Digital Out is a trademark
of DTS, Inc. © DTS, Inc. All Rights Reserved.
Open source software notice information
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained
in this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
ENGLISH
ENG
LICENSES
4
SAFETY INSTRUCTIONS
ENG
ENGLISH
Safety instRUctions
Please read these safety precautions carefully before using the product.
Viewing 3D Imaging (Only 3D models)
WARNING
Viewing Environment
yy Viewing Time
-- When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a
long period of time may cause headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or chronic illness
yy Some users may experience a seizure or other abnormal symptoms when they are exposed to
a flashing light or particular pattern from 3D contents.
yy Do not watch 3D videos if you feel nausea, are pregnant and/ or have a chronic illness such as
epilepsy, cardiac disorder, or blood pressure disease, etc.
yy 3D Contents are not recommended to those who suffer from stereo blindness or stereo anomaly.
Double images or discomfort in viewing may be experienced.
yy If you have strabismus (cross-eyed), amblyopia (weak eyesight) or astigmatism, you may have
trouble sensing depth and easily feel fatigue due to double images. It is advised to take frequent
breaks than the average adult.
yy If your eyesight varies between your right and left eye, revise your eyesight prior to watching 3D
contents.
Symptoms which require discontinuation or refraining from watching 3D contents
yy Do not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking.
yy When these symptoms are experienced, stop using/watching 3D contents and get enough rest
until the symptom subsides.
-- Consult your doctor when the symptoms persist. Symptoms may include headache,
eyeball pain, dizziness, nausea, palpitation, blurriness, discomfort, double image, visual
inconvenience or fatigue.
SAFETY INSTRUCTIONS
Viewing Environment
yy Viewing Distance
-- Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If
you feel discomfort in viewing 3D contents, move further away from the TV.
Viewing Age
yy Infants/Children
-- Usage/ Viewing 3D contents for children under the age of 5 are prohibited.
-- Children under the age of 10 may overreact and become overly excited because their vision
is in development (for example: trying to touch the screen or trying to jump into it). Special
monitoring and extra attention is required for children watching 3D contents.
-- Children have greater binocular disparity of 3D presentations than adults because the
distance between the eyes is shorter than that of adults. Therefore they will perceive more
stereoscopic depth compared to adults for the same 3D image.
yy Teenagers
-- Teenagers under the age of 19 may react with sensitivity due to stimulation from light in 3D
contents. Advise them to refrain from watching 3D contents for a long time when they are
tired.
yy Elderly
-- The elderly may perceive less 3D effect compared to the young. Do not sit closer to the TV
than the recommended distance.
Cautions when using the 3D glasses
yy
yy
yy
yy
yy
ake sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly.
M
Do not use 3D glasses instead of your normal glasses, sunglasses or protective goggles.
Using modified 3D glasses may cause eye strain or image distortion.
Do not keep your 3D glasses in extremely high or low temperatures. It will cause deformation.
The 3D glasses are fragile and are easily scratched. Always use a soft, clean piece of cloth
when wiping the lenses. Do not scratch the lenses of the 3D glasses with sharp objects or clean/
wipe them with chemicals.
ENGLISH
ENG
CAUTION
5
6
INSTALLATION PROCEDURE
ENG
ENGLISH
NOTE
yy Image shown may differ from your TV.
yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy The available menus and options may differ from the input source or product model that you are
using.
yy New features may be added to this TV in the future.
yy The TV can be placed in standby mode in order to reduce the power consumption. And the
TV should be turned off if it will not be watched for some time, as this will reduce energy
consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1
2
3
4
Open the package and make sure all the accessories are included.
Attach the stand to the TV set.
Connect an external device to the TV set.
Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV
may take a few minutes.
ASSEMBLING AND PREPARING
7
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
A
*A <
= 10 mm
A
*B <
= 18 mm
yy Use a certified cable with the HDMI logo attached.
yy If you do not use a certified HDMI cable, the screen may not display or a connection error may
occur. (Recommended HDMI Cable Types)
-- High-Speed HDMI®/™ Cable
-- High-Speed HDMI®/™ Cable with Ethernet
ENGLISH
ENG
ASSEMBLING AND PREPARING
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
FLASHBK
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
or
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Remote control, Batteries
(AAA)
(See p. 31, 32)
Owner’s manual
Isolator
(Depending on model)
(See p. 10)
Power cord
(Depending on model)
Cable Managements
2EA
(Only LY750*, LY755*,
LY96**)
(See p. 22)
Cable Holder
(Depending on model)
(See p. 22, 23)
Component Gender Cable
(Depending on model)
(See p. 28)
Wall Mount Spacers
2EA
(Only 42LY75**)
(See p. 22)
Stand Screws
4EA, M4 x L20
(Only 32LY750*, 32LY755*,
42/47/55LY751*)
6EA, M4 x L20
(Only 32/39LY751*)
(See p. 15, 16)
Stand Screws
4EA, M4 x L14
(Only 42/47/55LY750*,
42/47/55LY755*,
42/47/55LY751*,
42/47/55LY96**)
(See p. 15, 17)
Stand Screws
4EA, M4 x L12
(Only 60LY96**)
(See p. 15)
Stand Bases
(Only LY750*, LY755*,
LY96**)
(See p. 15)
ASSEMBLING AND PREPARING
9
ENGLISH
ENG
Stand Base/Stand Body
(Only LY751*)
(See p. 15, 16)
Power Cord Holder/Screw
1EA
(Only 39/42/47/55LY751*)
(See p. 23)
Torx Plus Star-Head
Screws
2EA
(Only LY751*)
(See p. 16, 17)
Rubbers
2EA
(Only LY751*)
(See p. 17)
Washers for Stand Fixing
2EA
(Depending on model)
(See p. 19)
Nuts for Stand Fixing
2EA
(Depending on model)
(See p. 19)
Screws for Stand Fixing
2EA
(Depending on model)
(See p. 19)
10
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yy Antenna Isolator Installation Guide
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND
of antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna
contact might be heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the
wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
1 Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
2 Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a
cable distribution system using coaxial cable, may in some circumstances create a fire hazard.
Connection to a cable distribution system has therefore to be provided through a device providing
electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING
11
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
LG Audio Device
AN-MR300
Magic remote
AN-MR500
Magic remote
AG-F***
Cinema 3D Glasses
Compatibility
LY75**
LY96**
LG Audio Device
•
•
AN-MR300
Magic Remote
•
AN-MR500
Magic Remote
•
AG-F***
Cinema 3D Glasses
•
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
ENGLISH
ENG
Separate purchase
12
ASSEMBLING AND PREPARING
ENG
ENGLISH
Parts and Button
B type : LY751*
A type : LY750*, LY755*
Screen
Speakers
Screen
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
Remote control and
Intelligent1 sensors
Power Indicator
Joystick Button2
C type : LY96**
Screen
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
Joystick Button2
Joystick Button2
ASSEMBLING AND PREPARING
13
NOTE
yy You can set the power indicator light to on or off by selecting OPTION or General in the main
menus.
Using the Joystick button
You can simply operate the TV functions by pressing to turn On/Off or sliding your finger over joystick
button moving up, down, left or right.
Basic Functions
Power On
When the TV is turned off, place your finger on the joystick
button and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick
button and press it once for a few seconds and release it.
Volume
Control
If you place your finger over the joystick button and move it left
or right, you can adjust the volume level you want.
If you place your finger over the joystick button and move it up
Programmes
or down, you can scrolls through the saved programmes you
Control
want.
NOTE
yy When your finger over the joystick button and push it to the up, down, left or right, be careful not
to press the joystick button. If you press the joystick button first, you may not be able to adjust
the volume level and saved programmes.
Adjusting the Menu
(Only LY96**)
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items( , ,
) moving the joystick button left or right.
TV Off
Turns the power off.
Close
Closes Clears on-screen displays and returns to
TV viewing.
Input
Changes the input source.
ENGLISH
ENG
1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding
environment.
2 Joystick Button - This button is located below the TV screen.
14
ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and Moving the TV
Please note the following advice to prevent the TV from
being scratched or damaged and for safe transportation
regardless of its type and size.
yy When transporting a large TV, there should
be at least 2 people.
yy When transporting the TV by hand, hold the
TV as shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as
this may result in damage to the screen.
yy It is recommended to move the TV in
the box or packing material that the TV
originally came in.
yy Before moving or lifting the TV, disconnect
the power cord and all cables.
yy When holding the TV, the screen should
face away from you to avoid damage.
yy When transporting the TV, do not expose
the TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
yy Do not apply excessive pressure to cause
flexing /bending of frame chassis as it may
damage screen.
CAUTION
yy Hold the top and bottom of the TV
frame firmly. Make sure not to hold the
transparent part, speaker, or speaker grill
area.
yy When handling the TV, be careful not to
damage the protruding joystick button.
(Image shown may differ from your TV.)
ASSEMBLING AND PREPARING
32/39LY751*
Image shown may differ from your TV.
1
Attaching the Stand
M4 x L20
LY750*, LY755*, LY96**
4EA
1
A stand base
Stand Body
B stand base
1
Stand Base
2
2
1 Attach the stand to the TV using the upper
mounting hole on the back of the TV.
2 Attach the stand to the TV using the lower
connection on the back of the TV.
2
M4 x L12
(Only 60LY96**)
M4 x L14
(Only 42/47/55LY750*,
42/47/55LY755*,
42/47/55LY96**)
4EA M4 x L20
(Only 32LY750*,
32LY755*)
ENGLISH
ENG
Setting up the TV
15
16
ASSEMBLING AND PREPARING
ENG
ENGLISH
42/47/55LY751*
3
1
M4 x L20
M4 x L20
2EA
4EA
or
Stand Body
Torx Plus Star-Head Screws
2EA
Tighten the two Torx head screws
(supplied with TV) with a Torx Bit Driver
(not supplied with TV).
Stand Base
2
ASSEMBLING AND PREPARING
CAUTION
M4 x L14
4EA
or
M4 x L14
2EA
Torx Plus Star-Head Screws
2EA
Tighten the two of these four screws
and the two Torx screws (supplied with
TV) to secure the TV. Tighten the two
Torx screws with a Torx Bit Driver (not
supplied with TV).
yy When attaching the stand to the TV
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
yy Make sure that the screws are fastened
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.)
Do not use too much force and over
tighten the screws; otherwise screw may
be damaged and not tighten correctly.
NOTE
yy Remove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
yy The rubber will protect the opening
from accumulating dust and dirt. When
installing the wall mounting bracket, use
the rubber. (Only LY751*)
Rubber
2EA
ENGLISH
ENG
3
17
18
ASSEMBLING AND PREPARING
ENG
ENGLISH
Mounting on a table
1 Lift and tilt the TV into its upright position on
a table.
-- Leave a 10 cm (minimum) space from
the wall for proper ventilation.
10 cm
m
10 c
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
yy Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
Using the Kensington security system
(This feature is not available for all models.)
yy Image shown may differ from your TV.
The Kensington security system connector
is located at the rear of the TV. For more
information of installation and using, refer to the
manual provided with the Kensington security
system or visit http://www.kensington.com.
WARNING
yy If a television is not positioned in a
sufficiently stable location, it can be
potentially hazardous due to falling. Many
injuries, particularly to children, can be
avoided by taking simple precautions such
as:
»» Using cabinets or stands
recommended by the manufacturer of
the television.
»» Only using furniture that can safely
support the television.
»» Ensuring the television is not
overhanging the edge of the
supporting furniture.
»» Not placing the television on tall
furniture (for example, cupboards or
bookcases) without anchoring both
the furniture and the television to a
suitable support.
»» Not standing the televisions on cloth
or other materials placed between the
television and supporting furniture.
»» Educating children about the dangers
of climbing on furniture to reach the
television or its controls.
Adjusting the angle of the TV to suit view
(Only LY751*)
Swivel 20 degrees to the left or right and adjust
the angle of the TV to suit your view.
20˚
20˚
Connect the Kensington security system cable
between the TV and a table.
CAUTION
yy When adjusting the angle of the product,
watch out for your fingers.
»» Personal injury may occur if hands
or fingers are pinched. If the product
is tilted too much, it may fall, causing
damage or injury.
ASSEMBLING AND PREPARING
Attaching the TV to a desk
ENGLISH
ENG
B type )
(Depending on model)
The TV should be attached to a desk so it cannot
be pulled in a forward/backward direction,
potentially causing injury or damaging the
product.
A type )
2-Washers for Stand Fixing,
2-Nuts for Stand Fixing,
2-Screws for Stand Fixing
(Supplied with TV)
Stand
4-Screws
(Not supplied with TV)
Stand
Desk
Desk
NOTE
yy Screw : M5 x L (*L: Table depth + 8~10
mm)
ex) Table depth: 15 mm, Screw : M5 x 25
19
20
ASSEMBLING AND PREPARING
ENG
ENGLISH
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
-- If there are bolts inserted at the eyebolts position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and
the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope.
Make sure to keep the rope horizontal with
the flat surface.
CAUTION
yy Make sure that children do not climb on or
hang on the TV.
NOTE
yy Use a platform or cabinet that is strong
and large enough to support the TV
securely.
yy Brackets, bolts and ropes are not
provided. You can obtain additional
accessories from your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be
performed by a qualified professional installer.
We recommend the use of LG’s wall mount
bracket.
When you do not use LG’s wall mount bracket,
please use a wall mount bracket where the
device is adequately secured to the wall with
enough space to allow connectivity to external
devices.
10 cm
10 cm
10 cm
10 cm
ASSEMBLING AND PREPARING
Separate purchase (Wall Mounting Bracket)
Model
32/39LY75** 42/47/55LY75**
VESA (mm) (A x B)
200 x 200
400 x 400
Standard screw
M6
M6
Number of
screws
4
4
Wall mount
bracket
LSW240B
MSW240
LSW440B
MSW240
Model
42/47/55/60LY96**
VESA (mm) (A x B)
400 x 400
Standard screw
M6
Number of
screws
4
Wall mount
bracket
LSW440B
Wall mount bracket
LSW240B
LSW440B
A
B
MSW240
CAUTION
yy Disconnect the power first, and then move
or install the TV. Otherwise electric shock
may occur.
yy If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorised LG wall mount and
contact the local dealer or qualified
personnel.
yy Do not over tighten the screws as this may
cause damage to the TV and void your
warranty.
yy Use the screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the
manufacturer’s warranty.
ENGLISH
ENG
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described
in the following table.
21
22
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yy Use the screws that are listed on the
VESA standard screw specifications.
yy The wall mount kit includes an installation
manual and necessary parts.
yy The wall mount bracket is not provided.
You can obtain additional accessories
from your local dealer.
yy The length of screws may differ depending
on the wall mount. Make sure to use the
proper length.
yy For more information, refer to the manual
supplied with the wall mount.
yy When attaching a wall mounting bracket
to the TV, insert the wall mount spacers
into the TV wall mount holes to adjust the
vertical angle of the TV. (Only 42LY75**)
Tidying cables
Image shown may differ from your TV.
(Only LY750*, LY755*, LY96**)
1 Gather and bind the cables with the cable
holder.
2 Fix the Cable Management firmly to the TV.
Cable Holder
Cable Management
(Only 32LY751*)
1 Gather and bind the cables with the cable
holder.
Wall Mount Spacer
Cable Holder
ASSEMBLING AND PREPARING
1 Install the power cord holder and power
cord. It will help prevent the power cable
from being removed by accident.
2 Gather and bind the cables with the cable
holder.
Power Cord Holder/
Screw
Cable Holder
CAUTION
yy Do not move the TV by holding the cable
holder, as the cable holder may break,
and injuries and damage to the TV may
occur.
ENGLISH
ENG
(Only 39/42/47/55LY751*)
23
24
MAKING CONNECTIONS
ENG
ENGLISH
MAKING CONNECTIONS
This section on MAKING CONNECTIONS
mainly uses diagrams for the 42LY750* models.
Connect various external devices to the TV and
switch input modes to select an external device.
For more information on external device’s
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB
storage devices, PC, gaming devices, and other
external devices.
NOTE
yy The external device connection may differ
from the model.
yy Connect external devices to the TV
regardless of the order of the TV port.
yy If you record a TV program on a DVD
recorder or VCR, make sure to connect
the TV signal input cable to the TV
through a DVD recorder or VCR. For
more information on recording, refer to
the manual provided with the connected
device.
yy Refer to the external equipment’s manual
for operating instructions.
yy If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
yy In PC mode, there may be noise
associated with the resolution, vertical
pattern, contrast or brightness. If noise is
present, change the PC output to another
resolution, change the refresh rate to
another rate or adjust the brightness and
contrast on the PICTURE menu until the
picture is clear.
yy In PC mode, some resolution settings
may not work properly depending on the
graphics card.
yy USB storage device is recognizable.
Antenna Connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
ANTENNA/
CABLE IN
(*Not Provided)
NOTE
yy Use a signal splitter to use more than 2
TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
yy If the image quality is poor with an
antenna connected, try to realign the
antenna in the correct direction.
yy An antenna cable and converter are not
supplied.
yy Supported DTV Audio: MPEG, Dolby
Digital, Dolby Digital Plus, HE-AAC
MAKING CONNECTIONS
(Only LY96**)
ENGLISH
ENG
HDMI Connection
25
Transmits the digital video and audio signals
from your PC to the TV. Connect the PC and the
TV with the HDMI cable as shown. Choose any
HDMI input port to connect. It does not matter
which port you use.
ARC (Audio Return Channel)
yy An external audio device that supports
SIMPLINK and ARC must be connected
using HDMI IN 2 (ARC) port.
yy When connected with a high-speed
HDMI cable, the external audio device
that supports ARC outputs optical SPDIF
without additional optical audio cable
and supports the SIMPLINK function.
(*Not Provided)
(Only LY75**)
HDMI
DVD / Blu-Ray / HD Cable Box / HD STB / PC
NOTE
(*Not Provided)
HDMI
DVD / Blu-Ray / HD Cable Box / HD STB / PC
yy It is recommended to use the TV with
the HDMI connection for the best image
quality.
yy Use the latest High Speed HDMI™ Cable
with CEC (Customer Electronics Control)
function.
yy High Speed HDMI™ Cables are tested
to carry an HD signal up to 1080p and
higher.
yy Supported HDMI Audio format :
Dolby Digital (32 KHz, 44.1 KHz, 48 KHz),
PCM (32 KHz, 44.1 KHz, 48 KHz, 96 KHz,
192 KHz),
DTS supported. (44.1 KHz, 48KHz - Only
LY96**),
DTS not supported. (Only LY75**)
26
MAKING CONNECTIONS
ENG
ENGLISH
MHL Connection
Audio Connection
(Only LY96**)
You may use an optional external audio system
instead of the built-in speaker.
Mobile High-definition Link (MHL) is an interface
for transmitting digital audiovisual signals from
mobile phones to television sets.
Digital Optical Audio Connection
Transmits a digital audio signal from the TV to an
external device. Connect the external device and
the TV with the optical audio cable as shown.
MHL passive cable
(*Not Provided)
Mobile phone
(*Not Provided)
NOTE
yy Connect the mobile phone to the HDMI
IN 3 (MHL) port to view the phone screen
on the TV.
yy The MHL passive cable is needed to
connect the TV and a mobile phone.
yy This only works for the MHL-enabled
phone.
yy Some applications can be operated by the
remote control.
yy Remove the MHL passive cable from the
TV when:
»» the MHL function is disabled
»» your mobile device is fully charged in
standby mode
OPTICAL AUDIO IN
Digital Audio System
NOTE
yy Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
yy Audio with ACP (Audio Copy Protection)
function may block digital audio output.
MAKING CONNECTIONS
Network Setup
Connect the external speaker to the SPEAKER
OUT jack on the TV.
Wired network Connection
yy Image shown may differ from your TV.
This TV can be connected to a Pro:Centric
server via the LAN port. After making the
physical connection, the TV needs to be set up
for network communication. Connect the LAN
port of the Modem or Router from Pro:Centric
server to the LAN port on the TV.
SPEAKER OUT
(*Not Provided)
AUX LAN LAN
Control port for Speaker out
UP
2
DOWN
GND
RIGHT
LEFT
GND
1
Broadband Modem
Router
Pro:Centric Server
NOTE
Broadband Modem
yy Use only with the 3 Pole 3.5 mm Stereo
Jack.
yy Do not connect your headphones or
earphones to the port for connecting a
SPEAKER OUT.
Method of Volume control port
Cable
Spec.
Each Up/ Down
pin is pulled to
3.3 V with CPU
GPIO.
GND / Up / Down CPU detects
transition from
3.3 V to GND
level for volume
control.
Pro:Centric Server
1
Connect the LAN port of the Modem or
Router to the LAN port on the TV.
2
Connect the LAN port of the PC to the
AUX LAN port on the TV.
CAUTION
yy Do not connect a modular phone cable to
the LAN port.
yy Since there are various connection methods,
please follow the specifications of your
telecommunication carrier or internet service
provider.
ENGLISH
ENG
Speaker Output Setup
27
28
MAKING CONNECTIONS
ENG
ENGLISH
Component Connection
(Only LY96**)
Transmits the analogue video and audio signals
from an external device to the TV. Connect the
external device and the TV with the component
cable as shown.
(Only LY75**)
(*Not Provided)
GREEN
BLUE
RED
WHITE
RED
L
(Depending on model)
VIDEO
RED
WHITE
RED
BLUE
GREEN
GREEN
R
AUDIO
GREEN
BLUE
RED
GREEN
BLUE
RED
DVD / Blu-Ray / HD Cable Box
NOTE
(*Not Provided)
VIDEO
RED
WHITE
RED
BLUE
GREEN
L
R
AUDIO
DVD / Blu-Ray / HD Cable Box
yy If cables are not installed correctly, it could
cause this image to display in black and
white or with distorted colours.
MAKING CONNECTIONS
29
RGB-PC Connection
(Only LY96**)
(Only LY75**)
Transmits analog video and audio signals
from an external device to the TV. Connect the
external device and the TV with the composite
cable as shown.
Transmits the video signal from PC to the TV. To
transmit an audio signal, connect an audio
cable.
YELLOW
(*Not Provided)
WHITE
RED
RED
WHITE
YELLOW
VIDEO
(*Not Provided)
L (MONO) AUDIO R
DVD / Blu-Ray / HD Cable Box / VCR
PC
ENGLISH
ENG
Composite Connection
30
MAKING CONNECTIONS
USB Connection
Transmits the headphone signal from the TV to
an external device. Connect the external device
and the TV with the headphone as shown.
Connect a USB storage device such as s USB
flash memory, external hard drive or a USB
memory card reader to the TV and access the
SmartShare menu to use various multimedia
files.
H/P OUT
ENG
ENGLISH
Headphone Connection
(*Not Provided)
Headphone
NOTE
yy AUDIO menu items are disabled when
connecting a headphone.
yy When changing AV MODE with a
headphone connected, the change is
applied to video but not to audio.
yy Optical Digital Audio Out is not available
when connecting a headphone.
yy Headphone impedance: 16 Ω
yy Max audio output of headphone:
»» 9 mW to 15 mW (Only LY75**)
»» 0.627 mW to 1.334 mW (Only LY96**)
yy Headphone jack size: 0.35 cm
HUB
(*Not Provided)
USB
(*Not Provided)
NOTE
yy Some USB Hubs may not work. If a USB
device connected through a USB Hub
is not detected, connect it directly to the
USB port on the TV.
REMOTE CONTROL
31
This item is not included for all models.
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly. To replace batteries,
open the battery cover, replace batteries (1.5 V AAA) matching the
and
ends to the label inside the compartment, and close the battery cover. To remove
the batteries, perform the installation actions in reverse.
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
yy In Analogue TV and some countries, some remote control buttons may not work.
Make sure to point the remote control toward the remote control sensor on the TV.
(Only LY75**)
(POWER) Turns the TV on or off.
ENERGY SAVING Adjusts the brightness of the screen to reduce
energy consumption.
AV MODE Selects an AV mode.
INPUT Changes the input source.
TV/RAD
Selects Radio, TV and DTV programme.
Number buttons Enters numbers.
LIST Accesses the saved programme list.
Q.VIEW Returns to the previously viewed programme.
Adjusts the volume level.
FAV Accesses your favourite programme list.
RATIO Resizes an image.
Mutes all sounds.
MUTE
P
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
GUIDE Shows programme guide.
PORTAL Displays and removes hotel interactive menu.
INFO
Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus or
options.
OK
Selects menus or options and confirms your input.
SETTINGS Accesses the main menus.
(BACK) Returns to the previous level.
EXIT
Clears on-screen displays and return to TV viewing.
Coloured buttons These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
Teletext buttons ( TEXT/T.OPT) These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Control buttons (
) Controls the Premium contents,
SmartShare menus or the SIMPLINK compatible devices (USB or
SIMPLINK).
Accesses the AV devices connected with the HDMI cable
through HDMI-CEC. Opens the SIMPLINK menu.
Q.MENU Accesses the Quick menus.
ENGLISH
ENG
REMOTE CONTROL
32
REMOTE CONTROL
ENG
ENGLISH
(Only LY96**)
(POWER) Turns the TV on or off.
ENERGY SAVING Adjusts the brightness of the screen to reduce
energy consumption.
AV MODE Selects an AV mode. (Depending on model)
INPUT Changes the input source.
TV/RAD
Selects Radio, TV and DTV programme.
Number buttons Enters numbers.
LIST Accesses the saved programme list.
Q.VIEW Returns to the previously viewed programme.
Adjusts the volume level.
SMART Accesses the Home menus.
RATIO Resizes an image.
Mutes all sounds.
MUTE
Scrolls through the saved programmes.
P
Moves to the previous or next screen.
PAGE
GUIDE Shows programme guide.
PORTAL Displays and removes hotel interactive menu.
INFO
Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus or
options.
OK
Selects menus or options and confirms your input.
SETTINGS Accesses the main menus.
(BACK) Returns to the previous level.
EXIT Clears on-screen displays and return to TV viewing.
Coloured buttons These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
Teletext buttons ( TEXT/T.OPT) These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Control buttons (
) Controls the Premium contents,
SmartShare menus or the SIMPLINK compatible devices (USB or
SIMPLINK).
Used for viewing 3D video.
Q.MENU Accesses the Quick menus.
AD By Pressing AD button, audio descriptions function will be enabled.
MAINTENANCE
33
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the
wall outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted
mild detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may
result in scratches and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
ENGLISH
ENG
MAINTENANCE
34
TROUBLESHOOTING
ENG
ENGLISH
TROUBLESHOOTING
The software version can be updated for improvement in performance.Customer needs to ensure the
compatibility of customer’s equipment with LGE software. If needed, please consult with LGE and
upload revised software version according to the guidance provided by LGE.
Problem
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to
yy Check if the batteries are still working and properly installed ( to ,
).
No image display
and no sound is
produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Sleep Timer or Off Time feature is activated in the TIME or
Timers settings.
When connecting
to the PC (RGB1 /
HDMI), ‘No signal’
or ‘Invalid Format’ is
displayed.
yy Turn the TV off/on using the remote control.
1
yy Reconnect the RGB / HDMI cable.
yy Restart the PC with the TV on.
1 Only LY75**.
SPECIFICATIONS
(Only LY75**)
Wireless LAN module (TWFM-B006D) specification
Standard
IEEE802.11a/b/g/n
Frequency Range
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
Output Power (Max.)
802.11a: 11 dBm
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2.4 GHz: 11 dBm
802.11n - 5 GHz: 12.5 dBm
yy Because band channel used by the country could be different, the user can not change or
adjust the operating frequency and this product is set for the regional frequency table.
yy This device should be installed and operated with minimum distance 20 cm between the
device and your body. And this phrase is for the general statement for consideration of user
environment.
0197
(Only LY96**)
Wireless module (LGSBW41) Specifications
0197
Wireless LAN module
Standard
Frequency
ragne
Output
power (Max.)
Bluetooth module
IEEE 802.11a/b/g/n
Standard
Bluetooth Version 3.0
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
Frequency
ragne
2400 to 2483.5 MHz
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4 GHz: 16 dBm
802.11n - 5 GHz: 16 dBm
Output
power (Max.)
10 dBm or Lower
yy Because band channel used by the country could be different, the user can not change or
adjust the operating frequency and this product is set for the regional frequency table.
yy This device should be installed and operated with minimum distance 20 cm between the device
and your body. And this phrase is for the general statement for consideration of user
environment.
0197
ENGLISH
ENG
SPECIFICATIONS
35
36
SPECIFICATIONS
ENG
ENGLISH
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
MODELS
Dimensions
(W x H x D)
Weight
32LY750*
32LY755*
42LY750*
42LY755*
47LY750*
47LY755*
32LY750H-TA
32LY755H-TA
42LY750H-TA
42LY755H-TA
47LY750H-TA
47LY755H-TA
With stand (mm)
732 x 481 x 207
961 x 612 x 218
1073 x 676 x 247
Without stand (mm)
732 x 437 x 55.5
961 x 567 x 55.5
1073 x 629 x 55.8
With stand (mm)
6.2
9.5
12.7
Without stand (mm)
6.0
9.2
12.3
Power requirement
MODELS
Dimensions
(W x H x D)
Weight
AC 100-240 V~ 50 / 60 Hz
55LY750*
55LY755*
32LY751*
39LY751*
55LY750H-TA
55LY755H-TA
32LY751H-TA
39LY751H-TA
With stand (mm)
1243 x 772 x 247
732 x 482 x 282
885 x 572 x 282
Without stand (mm)
1243 x 725 x 56.8
732 x 437 x 55.5
885 x 524 x 55.5
With stand (mm)
17.7
8.9
10.9
Without stand (mm)
17.3
6.0
8
Power requirement
MODELS
Dimensions
(W x H x D)
Weight
AC 100-240 V~ 50 / 60 Hz
42LY751*
42LY751H-TA
47LY751H-TA
55LY751H-TA
961 x 617 x 325
1073 x 680 x 325
1243 x 771 x 325
Without stand (mm)
961 x 567 x 55.5
1073 x 629 x 55.8
1243 x 725 x 56.8
With stand (mm)
12.6
15.7
20.7
Without stand (mm)
9.2
12.3
17.3
AC 100-240 V~ 50 / 60 Hz
42LY96**
47LY96**
55LY96**
42LY960H-TA
47LY960H-TA
55LY960H-TA
With stand (mm)
949 x 611 x 218
1061 x 677 x 247
1231 x 772 x 247
Without stand (mm)
949 x 560 x 55.1
1061 x 623 x 55.1
1231 x 718 x 55.1
With stand (mm)
10.3
13.2
18.9
Without stand (mm)
10
12.8
18.5
MODELS
Weight
55LY751*
With stand (mm)
Power requirement
Dimensions
(W x H x D)
47LY751*
Power requirement
AC 100-240 V~ 50 / 60 Hz
SPECIFICATIONS
Weight
ENGLISH
ENG
60LY96**
MODELS
Dimensions
(W x H x D)
37
60LY960H-TA
With stand (mm)
1338.4 x 837 x 273.5
Without stand (mm) 1338.4 x 778.8 x 58.1
With stand (mm)
21.8
Without stand (mm)
21.3
AC 100-240 V~ 50
/ 60 Hz
Power requirement
Environment condition
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Digital TV
(Depend on Country)
Analogue TV
(Depend on Country)
Television System
DVB-T (DVB-T/T21)
PAL B/B, PAL B/G, PAL D/K, PAL-I
SECAM B/G, SECAM D/K
NTSC-M
Programme Coverage
VHF, UHF
VHF, UHF, CATV
Maximum number of
storable programmes
DVB-T/T2 & Analogue TV : 1,500
External Antenna
Impedance
75 Ω
1 Only DVB-T2 Support models.
38
SPECIFICATIONS
ENG
ENGLISH
Component port connecting information
HDMI-DTV Supported Mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
640 x 480
(Only LY96**)
31.469
31.5
59.94
60.00
720 x 480
31.47
31.5
59.94
60
720 x 576
31.25
50
1280 x 720
44.96
45
37.5
59.94
60
50
1920 x 1080
28.125
33.72
33.75
26.97
27.00
33.71
33.75
56.25
67.432
67.5
50
59.94
60.00
23.976
24.000
29.97
30.00
50.00
59.94
60.00
RGB-PC1, HDMI-PC Supported Mode
yy PC audio not supported. (Only LY96**)
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
640 x 480
31.469
59.94
60.31
800 x 600
37.879
1024 x 768
48.363
60.00
1152 x 864
54.348
60.053
1280 x 1024
63.981
60.020
1360 x 768
47.712
60.015
1920 x 1080
67.5
60
1 Only LY75**.
Component ports
on the TV
Video output ports
on DVD player
Y
PB
PR
Y
Y
PB
B-Y
PR
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(Only 50 Hz / 60 Hz)
SPECIFICATIONS
yy Video, which is input as below media contents is switched into the 3D screen automatically. The
method for 3D digital broadcast may differ depending on the signal environment. If video is not
switched automatically into 3D, manually convert the settings to view 3D images. For models
supporting Miracast / Intel® WiDi, you can set the 3D mode.
3D supported mode automatically
Input
Signal
480p
Horizontal
Frequency
(kHz)
31.469 / 31.5
Vertical
Frequency
(Hz)
59.94 / 60
62.938 / 63
576p
31.25
HDMI
1080i
1080p
DTV
Top & Bottom, Side by Side(Half),
Side by Side(Full)
Frame Packing, Line Alternative
50
62.5
720p
Playable 3D video format
Top & Bottom, Side by Side(Half),
Side by Side(Full)
Frame Packing, Line Alternative
37.50
50
44.96 / 45
59.94 / 60
75
50
89.91 / 90
59.94 / 60
28.125
50
33.72 / 33.75
59.94 / 60
56.25
50
67.432 / 67.5
59.94 / 60
26.97 / 27
23.97 / 24
28.125
25
33.716 /
33.75
29.976 / 30
43.94 / 54
23.97 / 24
56.25
25
67.432 / 67.5
29.976 / 30
56.25
50
67.432 / 67.5
59.94 / 60
Top & Bottom, Side by Side(Half),
Side by Side(Full)
Frame Packing, Line Alternative
Top & Bottom, Side by Side(Half),
Side by Side(Full)
Frame Packing, Field Alternative
Top & Bottom, Side by Side(Half),
Side by Side(Full)
Frame packing, Line Alternative
Top & Bottom, Side by Side(Half)
Signal
Playable 3D video format
Frame Compatible
Side by Side(Half), Top & Bottom
ENGLISH
ENG
3D supported mode (Only 3D models)
39
40
SPECIFICATIONS
ENG
ENGLISH
3D supported mode manually
Signal
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
DTV
HD / SD
-
-
ATV (CVBS)
SD
Input
1280 x 720p
1920 x 1080i
Component
1920 x 1080p
-
-
37.5
50
45
60
44.96
59.94
33.75
60
33.72
59.94
28.12
50
67.5
60
67.432
59.94
27
24
28.12
25
56.25
50
26.97
23.976
33.75
30
33.71
29.97
1024 x 768p
48.36
1360 x 768p
47.71
60
HDMI-PC
1920 x 1080p
67.5
Others
-
-
Playable 3D video format
2D to 3D, Side by Side(Half),
Top & Bottom
2D to 3D, Side by Side(Half),
Top & Bottom, Checker Board,
Single Frame Sequential,
Row Interleaving,
Column Interleaving
2D to 3D, Side by Side(Half),
Top & Bottom
SPECIFICATIONS
Signal
Input
Resolution
2D to 3D, Side by Side(Half),
Top & Bottom, Checker Board,
Frame Sequential,
Row Interleaving,
Column Interleaving
31.5
60
31.25
50
37.5
50
45
60
28.125
50
33.75
60
2D to 3D, Side by Sied(Half),
Top & Bottom
27
24
28.12
25
33.75
30
56.25
50
67.5
60
Under
704 x 480
-
-
2D to 3D
Over 704x480
under 1080p
interlaced
-
-
2D to 3D, Side by Side(Half),
Top & Bottom
HDMI-DTV
1080p
Miracast/
Intel® WiDi
Playable 3D video format
480p
1080i
USB (Photo)
Vertical
Frequency
(Hz)
576p
720p
USB (Movie)
Horizontal
Frequency
(kHz)
2D to 3D, Side by Side(Half),
Top & Bottom,Checker Board,
Row Interleaving,
Column Interleaving
2D to 3D, Side by Side(Half),
Top & Bottom, Checker Board,
Frame Sequential,
Row Interleaving,
Column Interleaving
Over 704x480
under 1080p
progressive
-
50 / 60
2D to 3D, Side by Side(Half),
Top & Bottom,Checker Board,
Row Interleaving,
Column Interleaving,
Frame Sequential
Over 704x480
under 1080p
progressive
-
Others
2D to 3D, Side by Side(Half),
Top & Bottom,Checker Board,
Row Interleaving,
Column Interleaving
Under
320 x 240
-
-
2D to 3D
Over 320 x 240
-
-
2D to 3D, Side by Side(Half),
Top & Bottom
1024 x 768p
-
30 / 60
1280 x 768p
-
30 / 60
1920 x 1080p
-
30 / 60
Others
-
-
2D to 3D, Side by Side(Half),
Top & Bottom
2D to 3D
ENGLISH
ENG
3D supported mode manually
41
42
SPECIFICATIONS
ENG
ENGLISH
Video Codec
(Only LY96**)
Extenstion
.asf
.wmv
.divx
.avi
Codec
Video
VC-1 Advanced Profile (WMVA excluded), VC-1 Simple
and Main Profiles
Audio
WMA Standard (WMA v1/WMA Speech excluded), WMA
9 Professional
Video
DivX3.11, DivX4, DivX5, DivX6, XViD(except 3 warp-point
GMC), H.264/AVC, Motion Jpeg, MPEG-4
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby
Digital, LPCM, ADPCM, DTS
.mp4
.m4v
.mov
Video
H.264/AVC, MPEG-4
Audio
AAC, MPEG-1 Layer III (MP3)
.3gp
.3g2
Video
H.264/AVC, MPEG-4
Audio
AAC, AMR-NB, AMR-WB
Video
MPEG-2, MPEG-4, H.264/AVC, VP8
Audio
Dolby Digital, PCM, DTS, MPEG-1 Layer I, II, MPEG-1
Layer III (MP3), AAC
Video
H.264/AVC, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby
Digital, Dolby Digital Plus, AAC, PCM
Video
MPEG-1, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3)
.mkv
.ts
.trp
.tp
.mts
.mpg
.mpeg
.dat
.vob
.rm
.rmvb
Video
MPEG-1, MPEG-2
Audio
Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM
Video
RV30, RV40
Audio
Realaudio6(cook), AAC LC, HE-AAC
yy This feature is available in certain countries only.
SPECIFICATIONS
(Only LY96**)
File Format
Item
Bit rate
.mp3
16 kHz - 48 kHz
Support
MPEG1, MPEG2
Bit rate
Sample freq.
Support
Channels
Bit rate
.ogg
Sample freq.
Support
Channels
Bit rate
.wma
32 Kbps - 320 Kbps
Sample freq.
Channels
.wav
Info
Sample freq.
Support
Channels
mono, stereo
~384 kHz
PCM
mono, stereo
64 Kbps - 500 Kbps
8 kHz - 48 kHz
Vorbis
mono, stereo
~1.5 Mbps
8 kHz - 192 kHz
WMA
up to 8 ch
yy The number of supported programmes may vary depending on the sample frequency.
Photo Format
(Only LY96**)
yy Only 2D models
File Format
Format
Resolution
.jpeg, .jpg, .jpe
JPEG
Minimum: 64 x 64
Maximum: 15360 (W) x 8640 (H) / Progressive Type: 1920
(W) x 1440 (H)
.png
PNG
Minimum: 64 x 64
Maximum: 1920 (W) x 1080 (H)
.bmp
BMP
Minimum: 64 x 64
Maximum: 1920 (W) x 1080 (H)
yy Only 3D models
File Format
Format
Resolution
.jps
JPS
Minimum: 64 x 64
Maximum: 15360 (W) x 8640 (H)
.mpo
MPO
4:3 size: 3648 x 2736, 2592 x 1944, 2048 x 1536
3:2 size: 3648 x 2432
ENGLISH
ENG
Audio Format
43
44
IR CODES
ENG
ENGLISH
IR CODES
yy This feature is not available for all models.
Code
(Hexa)
08
95
Function
(POWER)
ENERGY SAVING
Note
Code
(Hexa)
Remote control Button
(Power On/Off)
44
Remote control Button
43
SETTINGS Remote control Button
Remote control Button
Function
OK
Note
Remote control Button
30
AV MODE
Remote control Button
28
0B
INPUT
Remote control Button
5B
TV/RAD
Remote control Button
72
10-19
Number Key 0-9
Remote control Button
71
53
LIST
Remote control Button
63
1A
Q.VIEW
Remote control Button
61
02
Remote control Button
20
03
Remote control Button
21
T.OPT
(T.Option)
Remote control Button
SUBTITLE
Remote control Button
F0
EXIT
(RED)
(GREEN)
(YELLOW)
(BLUE)
TEXT
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
1E
FAV
Remote control Button
39
79
RATIO
Remote control Button
B1
Remote control Button
09
MUTE
Remote control Button
B0
Remote control Button
00
ꕌ P / PAGE
Remote control Button
BA
Remote control Button
01
P ꕍ / PAGE
Remote control Button
8E
Remote control Button
Remote control Button
8F
Remote control Button
AB
GUIDE
0C
PORTAL
Remote control Button
7E
SIMPLINK
Remote control Button
AA
INFO
Remote control Button
45
Q.MENU
Remote control Button
40
Remote control Button
7C
SMART
Remote control Button
41
Remote control Button
91
AD
07
Remote control Button
DC
06
Remote control Button
Remote control Button
Remote control Button
EXTERNAL CONTROL DEVICE SETUP
45
RS-232C Setup
ENGLISH
ENG
EXTERNAL CONTROL DEVICE SETUP
RS-232C Configurations
Connect the RS-232C (serial port) input jack to
an external control device (such as a computer
or an A/V control system) to control the product’s
functions externally.
Connect the serial port of the control device to the RS-232C jack on the product back panel. RXD
TXD
* Note : RS-232C connection cables are not supplied with the product.
GND
DTR
DSR
RTS
CTS
RS-232C IN
(CONTROL & SERVICE)
1
5
PC
2
3
5
4
6
7
8
D-Sub 9
TV
3
2
5
6
4
8
7
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9
3-Wire Configurations
(Not standard)
(*Not Provided)
Type of Connector: D-Sub 9-Pin
7-Wire Configurations
(Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
Male
CTS
PC
2
3
5
4
6
7
8
D-Sub 9
TV
3
TXD
2 RXD
5 GND
6 DTR
4 DSR
8 RTS
7 CTS
D-Sub 9
Set ID
6
No.
9
Pin name
1
3.5V
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
8
No Connection (5 V available in some
models)
No Connection
9
No Connection (12 V available in some
models)
Set ID number. “Real Data Mapping”.
1 Press SETTINGS or HOME to access the
main menus.
2 Press the Navigation buttons to scroll to
OPTION and press OK.
3 Press the Navigation buttons to scroll to Set
ID and press OK.
4 Scroll left or right to select a set ID number
and select Close. The adjustment range is
1-99.
5 When you are finished, press EXIT.
46
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
Communication Parameters
yy Baud rate : 9600 bps (UART)
yy Data length : 8 bits
yy Parity : None
yy Stop bit : 1 bit
yy Communication code : ASCII code
yy Use a crossed (reverse) cable.
Command Reference List
(Depending on Model)
COMMAND1
COMMAND2
DATA
(Hexadecimal)
01. Power
k
a
00 to 01
02. Aspect
Ratio
k
c
(See p. 48) 13. Balance
03. Screen
Mute
k
d
(See p. 48)
04. Volume
Mute
k
e
05. Volume
Control
k
06. Contrast
COMCOMMAND1 MAND2
12. Remote
Control Lock
Mode
DATA
(Hexadecimal)
k
m
00 to 01
k
t
00 to 64
14. Colour
Temperature
x
u
00 to 64
00 to 01
15. Energy
Saving
j
q
(See p. 50)
f
00 to 64
16. Auto
Configure
j
u
01
k
g
00 to 64
17. Equalize
j
v
(See p. 50)
07. Brightness
k
h
00 to 64
18. Tune
Command
m
a
(See p. 50)
08. Colour
k
i
00 to 64
19. Programme
Add/Skip
m
b
00 to 01
09. Tint
k
j
00 to 64
20. Key
m
c
(See p. 51)
10. Sharpness
k
k
00 to 32
21. Control
Back Light
m
g
00 to 64
11. OSD
Select
k
l
00 to 01
22. Input select
(Main)
x
b
(See p. 51)
NOTE
yy During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are
not executed and treated as NG.
EXTERNAL CONTROL DEVICE SETUP
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID]
[Data]
: Y
ou can adjust the set ID to choose desired monitor ID number in option menu.
Adjustment range is 1 to 99. W
hen selecting Set ID ‘0’, every connected set is
controlled.
* Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to
0x63) on transmission/receiving protocol.
: To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr]
[ ]
: Carriage Return - ASCII code ‘0x0D’
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At
this time, if the data is data read mode, it indicates present status data. If the data is data write
mode, it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data
from non-viable functions or communication errors.
Data 00 : Illegal Code
ENGLISH
ENG
Transmission / Receiving Protocol
47
48
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
01. Power (Command: k a)
03. Screen Mute (Command: k d)
►► To control Power On/Off of the set.
►► To select screen mute on/off.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To Show TV is Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’
data based on this format, Acknowledgement
data feed back presents status about each
function.
* OK Ack., Error Ack. and other message may
display on the screen when TV is power On.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display
On Screen Display(OSD). But, in case of
Screen mute on, TV will not display OSD.
04. Volume Mute (Command: k e)
►► To control volume mute on/off.
You can also adjust mute using the MUTE
button on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
02. Aspect Ratio (Command: k c)
(Main Picture Size)
►► To adjust the screen format. (Main picture
format) You can also adjust the screen format
using the Aspect Ratio n the Q.MENU. or
PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen
(4:3)
02 : W
ide screen
(16:9)
04 : Zoom
06 : Original
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : C
inema Zoom
1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or
4:3 screen aspect ratio.
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to Real data mapping.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p
50Hz / 60 Hz, 1080p 24 Hz / 30 Hz / 50 Hz /
60 Hz), Component( 720p, 1080i, 1080p 50
Hz / 60 Hz) mode, Just Scan is available.
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
* Full Wide is supported only for Digital,
Analogue, AV.
Data Min : 00 to Max : 64
Transmission [k][g][ ][Set ID][ ][Data][Cr]
* Refer to Real data mapping.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
11. OSD Select (Command: k l)
►► To adjust screen brightness.
You can also adjust brightness in the
PICTURE menu.
►► To select OSD (On Screen Display) on/off
when controlling remotely.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 64
* Refer to Real data mapping.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
08. Colour (Command: k i)
►► To adjust the screen Colour.
You can also adjust colour in the PICTURE
menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 64
* Refer to Real data mapping.
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE
menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to Real data mapping.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
12. Remote Control Lock Mode (Command: k
m)
►► To lock the front panel controls on the
monitor and remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control,
use this mode. When main power is on/off,
external control lock is released.
* In the standby mode, if key lock is on, TV will
not turn on by power on key of IR & Local Key.
13. Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO
menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data L : 0
0 to R : 64
* Refer to Real data mapping.
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the
PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 0
0 to Max : 32
* Refer to Real data mapping.
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
14. Colour Temperature (Command: x u)
►► To adjust colour temperature. You can also
adjust Colour Temperature in the PICTURE
menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to Real data mapping.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
07. Brightness (Command: k h)
49
50
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
15. Energy Saving (Command: j q)
►► To reduce the power consumption of the
TV. You can also adjust Energy Saving in
PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0 0 1st Band
0 0 0 0 0 0(decimal)
0 0 1 2nd Band 0 0 0 0 1 1(decimal)
0 1 0 3rd Band ... ... ... ... ...
Level
Low
Power
Low
Power
Low
Power
Low
Power
Low
Power
Low
Power
Description
3
2
1
0
0
0
0
0
Off
0
0
0
1
Minimum
0
0
1
0
Medium
0
0
1
1 Maximum
0
1
0
1 Screen Off
0
1
0
0
Auto
►► 'Auto' is available in TV that supports
'Intelligent Sensor'.
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
16. Auto Configure (Command: j u)
►► To adjust picture position and minimize image
shaking automatically. It works only in RGB
(PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set
Ack [v][ ][Set ID][ ][OK/NG][Data][x]
18. Tune Command (Command: m a)
►► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
Data 00 : High channel data
Data 01 : Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 : [Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
Data Min: 00 to Max: 7DH
17. Equalizer (Command : j v) (Only LY96**)
►► To adjust equalize.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
LSB
0
Frequency
...
1 0 0 5th Band 0 0 1 0 1 20(decimal)
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
0
Step
0 1 1 4th Band 0 0 0 1 1 19(decimal)
Power Saving
Function
7 6 5 4
0
7 6 5 Frequency 4 3 2 1 0
0
0
0
0
Data
0
0
EXTERNAL CONTROL DEVICE SETUP
►► To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
20. Key (Command: m c)
1
0
0
0
►► To send IR remote key code.
1
0
0
1
1
0
1
0
Transmission [m][c][ ][Set ID][ ][Data][Cr]
HDMI
Data IR CODES
Input Number
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Data
0
0
0
0
Input1
0
0
0
1
Input2
21. Control Back Light (Command: m g)
0
0
1
0
Input3
►► To control the backlight.
0
0
1
1
Input4
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Real data mapping
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
22. Input select (Command: x b)
(Main Picture Input)
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
LSB
0
0
External Input
0
0
0
0
Input Number
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
0
00 :
Step 0
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E :
Step 110
73 :
74 :
Step 115
Step 116
CF :
Step 199
FE :
FF :
Step 254
Step 255
ENGLISH
ENG
19. Programme Add/Skip (Command: m b)
51
Record the model number and serial
number of the TV.
Refer to the label on the back cover and
quote this information to your dealer when
requiring any service.
MODEL
SERIAL
(Only DTV)
Download PDF

advertising