LG | DT6101SAU | LG DT6101SAU Owner’s Manual

Model Numbers
DT6101SAU
DT6101SSA
Instruction Manual
Part NO. 383EW5N001T(MFL30049915)
Instructions Manual
INDEX
RECOMMENDATIONS AND SUGGESTIONS ......................................................................................................................3
CHARACTERISTICS..............................................................................................................................................................4
INSTALLATION ......................................................................................................................................................................5
USE.........................................................................................................................................................................................7
MAINTENANCE......................................................................................................................................................................8
EN
2
2
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
The manufacturer will not be held liable for any damages resulting from
incorrect or improper installation.
The minimum safety distance between the cooker top and the extractor
hood is 650 mm.
Check that the mains voltage corresponds to that indicated on the rating
plate fixed to the inside of the hood.
For Class I appliances, check that the domestic power supply guarantees
adequate earthing.
Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible.
Do not connect the extractor hood to exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
If the extractor is used in conjunction with non-electrical appliances (e.g.
gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen
must have an opening communicating directly with the open air in order to
guarantee the entry of clean air.
Installation of the extractor hood over a solid-fuel burner(coal, wood,etc.)
which could constitute a potential fire hazard (e.g. due to flying sparks) is
only permitted if the burner is equipped with an enclosed, non-removable
cover and all country-specific regulations are observed. This restriction dose not apply to gas cookers and gas hobs.
Regulations concerning the discharge of air have to be fulfilled.
650 mm min.
USE
The extractor hood has been designed exclusively for household use to eliminate kitchen smells.
Never use the hood for purposes other than for which it has been designed.
Never leave high naked flames under the hood when it is in operation.
Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
The hood should not be used by children or persons not instructed in its correct use.
Do not use the appliance if it is damaged in any way.
Never operate the extractor hood without a grease filter.
Do not flambe food directly under the extractor hood.
MAINTENANCE
Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
Clean and/or replace the Filters after the specified time period.
Clean the hood using a damp cloth and a neutral liquid detergent.
Defective bulbs should be replaced immediately to prevent the remaining bulbs from overloading.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
EN
3
3
CHARACTERISTICS
Dimensions
12e
Components
Ref.
1
8
9
10a
10b
20
Q.ty Product Components
1 Hood Body, complete with: Controls, Light, Blower,
Filters
1 Directional Air Outlet grille
1 Flange ø 150 mm
1 Reducer Flange ø 150-120 mm
1 Damper
1 Closing element
Ref.
12a
12e
12f
Q.ty
4
2
5
10b
9
10a
1
Installation Components
Screws 3,5 x 16
Screws 2,9 x 12,7
Screws 2,9 x 9,5
Q.ty Documentation
1 Instruction Manual
8
12a
20
12f
EN
4
4
INSTALLATION
Drilling the Support surface and Fitting the Hood
• The Hood can be fitted directly on the
lower surface of the Wall Units (650 mm
min. above the Cooker Top) using the snapon Side Supports.
• Make an opening on the lower surface of
the Wall Unit, as indicated. (fig.1)
• Choose the correct flange measure basing
on the air outlet diameter and insert it to the
upper air outlet opening. (fig.2)
• Screw the closing profile 20 onto the rear
part of the hood, using the screws 12f (2.9
x 9.5) provided. (fig.3)
• Open the sliding suction panel.
• Remove the metal grease filters one by one
after having disconnected the relative fastening elements.
• Close the sliding suction panel again.
• Insert the Hood until the snap-on side supports click into place. (fig.4)
• Open the sliding suction panel.
• Lock in position by tightening the screws
Vf from underneath the Hood. (fig.4)
• If necessary, adjust the whole filter holder
unit and proceed as follows:
• Loosen the four adjustment screws Vr
and close the sliding panel again. (fig.5)
• Move the entire filter holder unit until it
is properly aligned with the wall unit.
(fig.6)
• Keeping the hood canopy still, open the
sliding panel and lock the adjustment
screws again. (fig.5)
• The hood can now be fastened to the
wall unit using the four screws 12a (3.5
x 16) provided. (fig.7)
• Replace the metal grease filters.
• Close the sliding suction panel again.
1
162
10b
523
10a
9
10a
2
3
4
V
5
6
12a
7
EN
5
5
ø 120
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to
the chimney using either a flexible or rigid pipe ø 150
or 120mm, the choice of which is left to the installer.
10a
10b
9
• Install the Flange ø 150 mm 9.
• Install the Dumper 10b ø 150 on the Flange ø 150 9.
ø 150
To install a ø 120
• Install a reducer Flange 10a on the Dumper 10b.
• Fix the pipe in position using sufficient pipe clamps
(not supplied).
• Remove any activated charcoal filters.
RECIRCULATION VERSION AIR OUTLET
• Cut a hole ø 155 mm in the wall unit over the hood.
• Insert the flange 9 on the hood body outlet.
• Connect the hood body outlet to the top part of the
wall unit using a rigid or flexible pipe ø 150 mm, to
be selected by the installer.
• Fix the pipe in position using sufficient pipe clamps
(not supplied).
• Fix the directional grille 8 on the recirculation air
outlet using the 2 screws 12e (2,9 x 9,5) provided.
• Ensure that the activated charcoal filters have been
inserted.
10b
9
12e
8
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3
mm..
EN
6
6
USE
L
M
By pulling out the sliding panel it is possible to automatically activate all the hood functions.
By simply closing the sliding panel all the functions are switched off.
SWITCH
FUNCTIONS
L
Light
Switches the lighting system on and off
M
Motor
Switches the extractor motor on and off
1. Low speed, used for a continuous and silent air change in the presence
of light cooking vapour.
2. Medium speed, suitable for most operating conditions, thanks to an optimum relation between hood performance and noise.
3. Maximum speed, suitable when the highest cooking vapour emission
has to be eliminated for longer periods.
EN
7
7
MAINTENANCE
Grease filters
CLEANING METAL CASSETTE GREASE FILTERS
• The filters must be cleaned every 2 months, or more frequently
in case of particularly heavy use of the hood. Filters can be
washed in a dishwasher.
• Pull out the sliding suction panel.
• Remove the filters one by one, after having disconnected the
relative fastening elements.
• Wash the filters, taking care not to bend them. Let them get dry
before refitting them. (The colour of the filter surface may
change throughout the time but this has no influence to the filter efficiency).
• When refitting the filters, make sure that the handle is visible
on the outside.
• Close the sliding suction panel.
Charcoal filter (Recycling version)
REPLACING CHARCOAL FILTERS
• These filters are not washable and cannot be regenerated, and
must be replaced approximately every four months or more
frequently by particularly heavy use.
• Pull out the sliding suction panel.
• Remove the grease filters.
• Remove the saturated carbon filter by releasing the fixing
hooks
• Replace the grease filters.
• Close the sliding suction panel.
Light Replacement
20 W Halogen lamp.
• Remove the metal terminals fixing the metal panel.
• Slide the metal panel out of one of the fastening clips. Lower
the unfastened part of the panel slightly, so that it can be completely removed.
• Extract the lamp from the Support.
• Replace with another of the same type, making sure that the
two pins are properly inserted in the lamp holder socket holes
• Replace the metal panel in reverse order.
When switched on, the halogen bulbs become very hot. Even
for some time after the bulbs have been switched off there is
still a risk of burns.
EN
8
8
436003255_ver2
Download PDF