LG | LD-1415M1 | LG LD-1415M1 Owner’s Manual

DISHWASHER
OWNER'S MANUAL
MODEL : LD-1415T1
LD-1415M1
LD-1415W1
Please read this manual carefully before operating your
dishwasher. Retain it for future reference.
CONTENTS
SAFETY AND CAUTION
3
INSTALLATION INSTRUCTIONS
5
PARTS NAME
9
FUNCTION OF CONTROL BUTTON
10
HOW TO USE AND OPERATE
12
OPERATING SEQUENCE
17
PROGRAM
18
USER MAINTENANCE INSTRUCTIONS
19
TROUBLE SHOOTING GUIDE
20
SPECIFICATION
SAFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING - When using your dishwasher, follow basic precautions,
including the following:
During use
• Please read this manual carefully before
using the dishwasher for the first time.
• This manual contains very important
notes regarding the installation, use and
maintenance of your dishwasher.
• The manufacturer can not be responsible
for problems caused by ignoring these
safety and caution instructions.
• This dishwasher is designed for normal
household use.
• Do not use the dishwasher for industrial
and commercial use, or other purpose.
• The appliance is not intended for use by
young children or infirm persons without
supervision.
• Only suitable household utensils should
be placed in the dishwasher.
(Please avoid utensils; that are nonheatresistant, metal decorated, etc.)
• Do not use any kinds of solvent in your
dishwasher. They may cause an explosion
or fire.
• Do not spray water on the appliance.
It may cause the failure of electric parts or
electric shock.
• Do not push down or sit on the inner door
when the door opened. It may cause the
deformation or failure of your dishwasher.
• Do not use the detergent for hand
washing.
The detergent for dishwasher should be
used for normal operation.
• This appliance is fitted with a safety
function that automatically stops the
operation of the dishwasher when it is
exposed to heavy disturbance on its
mains.
• Dishwasher detergents are strongly
alkaline. They can be extremely
dangerous if swallowed. Avoid contact
with skin and eyes and keep children
away from the dishwasher when the door
is open.
Check that the detergent receptacle is
empty after completion of the wash cycle.
• Some pre-treatment sprays or liquids can
damage your dishwasher’s control panel
and plastic components, so do not use
these products on or around your
dishwasher.
• Be careful! Water could be splashed out
when door is opened.
During installation
• Electrical connection must be in
accordance with the rating label.
• Electrical safety is only guaranteed when
the earth system of your house is in
accordance with the related local
regulations.(Do not use an extension cable
or cord.)
• If the hot water exceeds 65ºC, adjust the
water heater setting. If the hot water
temperature can not be maintained below
65ºC, the dishwasher must be connected
to cold water.
• If power supply cord is damaged, it must
only be replaced by the manufacturer or
its service agent or a similar qualified
person in order to avoid a hazard.
• This appliance must be positioned so that
the plug is accessible.
• The appliance is to be connected to the
water mains using new hose-sets and that
old hose-sets should not be reused.
3
SAFETY AND CAUTION
Child Safety
• Controls may be locked using “Child Lock” mode to prevent from all the setting from being
changed by a child.
• Keep children away from detergents and rinse-aids.
• Do not allow children to operate the dishwasher.
• Young children should be supervised to ensure that they do not play with the appliance.
CAUTION concerning the Power Cord
• Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to be certain.
• Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire. Periodically examine the cord
of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and
the point where the cord exits the appliance.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and grounded in accordance
with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can
result in a risk of electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the appliance is
properly grounded. Do not modify the plug provided with the
appliance; if it will not fit the outlet have a proper outlet installed by
a qualified electrician.
4
INSTALLATION INSTRUCTIONS
WARNING
Step 2 :
PREPARE ELECTRICAL WIRING
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
CAUTION
For personal safety, remove house fuse
or open circuit breaker before installation.
Do not use an extension cord or adapter
plug with this appliance. Electrical and
grounding connections must comply with
the national electrical code/provincial and
municipal code and/or other local codes.
Step 1 :
PREPARE CUPBOARD OPENING
1 This dishwasher is designed to fit to the
size shown as below.
1 This appliance must be supplied with
correct rating voltage and hertz as shown
on instruction manual, and connected to
an individual, properly grounded branch
circuit, protected by minimum 15 amp
circuit breaker or time delay fuse.
Wiring must be 2 wires with ground.
2 Select a location as close to sink as
possible for easy connections to water and
drain lines.
3 The dishwasher should not be installed
more than 3 meters from sink for proper
drainage.
4 If dishwasher is to be installed in a corner,
a minimum 5cm of space is required
between the washer and an adjacent
cabinet or a wall.
2 The power plug must be in a accessible
location adjacent to and not behind the
dishwasher and within 1.2 meters of the
dishwasher side.(See page 7 Fig.A)
3 The power plug must be correctly
earthed, if in doubt, have it checked by a
qualified Electrician. No other appliance
should be connected to the same plug
outlet by a double adapter or similar
plug.
Unit:mm
If bare chipboard is adjacent to or above
the dishwasher, it should be sealed with a
waterproofing paint or sealant to prevent
swelling due to steam.
5
INSTALLATION INSTRUCTIONS
Step 3 :
PREPARE DISHWASHER FOR
INSTALLATION
Step 4 :
INSTALL THE DISHWASHER IN
CUPBOARD
1 Lay the dishwasher on its back.
1 Before sliding the dishwasher into the
cupboard opening, all necessary final
height adjustment and balancing adjustment
should be done using the spanner.
2 Adjust the legs to the needed height of
cabinet as shown in below figure.
2 Slide the dishwasher into the cabinet
opening carefully. Make sure that the
drain hose inside the cabinet is not
kinked or stretched.
CAUTION
If the height of cupboard is below 850mm, you
should remove the top table by unscrewing
the 2 screws. (Two of rear)
6
INSTALLATION INSTRUCTIONS
Step 5 :
DRAIN LINE CONNECTION
1 If the end of drain hose does not fit to
the drain line, use a piece of rubber
connector(not supplied) that must be
resistant to heat and detergent and may
be obtained from a plumbing shop.
When the drain hose is connected to a
separate stand pipe, it is essential that an
air tight connection is made.
Refer to Fig.B
2 There are 2 typical connections as
shown in Figure A, B.
The “S” trap spigot must be drilled out
cleanly and free of obstruction to its
maximum internal diameter, if used for
drainage.
To prevent siphoning, one of the following
instruction methods must be followed:
When the drain hose is connected to a
sink “s” trap or waste disposal unit, the
hose must be looped up to the underside
of the bench top and secured.
Fig. B : Drainage connection - stand pipe.
Drain Hose Extension
Extend Drain Hose as shown below.
Fig. A
CAUTION
When you connect or extend Drain Hose,
make sure that drain hose is not kinked.
(Bends should have 40 mm radius.)
7
INSTALLATION INSTRUCTIONS
Step 6 :
WATER SUPPLY CONNECTION
Step 8 :
HOW TO LEVEL THE PRODUCT
1 Connect the water supply hose to the
water tap as shown.(Some models consist
of an inlet valve and hose.)
This dishwasher may be fed with either
hot or cold water. If the water can not be
maintained below 65ºC, the dishwasher
must be connected to cold water.
After installing the product, if you feel some
sticky or hear a frictional sound between the
side portion of door and tub when you open or
close the door, you have to adjust the level of
product.
Case 1. In case the door is slanted to the right
2 When connecting, the sealant tape or
sealing compound to avoid water leaks.
Make sure that the line is not kinked or
sharply bent.
Fig. C
Water tap
• If the door is slanted to the right as shown in
figure C, repeat the procedure shown as below
until the door is operated normally.
1) Unscrew(counter-clockwise) the left leg of
back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
• When the product is correctly leveled, There
should be no slant , stickiness or friction sound.
Water supply
hose
Case 2. In case the door is slanted to the left
Step 7 :
FINAL CHECK AND ASSEMBLING
1 Securely hand tighten supply hose to
water supply.
Plug power supply cord into an
earthed the power plug and switch on.
2 After installing the product, operate
the dishwasher through one cycle
(Quick cycle is recommended) without
loading the dishes.
Through this, you can check for water
leak and operating conditions.
When you operate the product the
first, the noise may be occurred.
In that case, turn off power switch and
restart the dishwasher.
Fig. D
• If the door is slanted to the left as shown in
figure D, repeat the procedure shown as below
until the door is operated normally.
1) Unscrew(counter-clockwise) the right leg of
back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
• When the product is correctly leveled, There
should be no slant , stickiness or friction sound.
8
PARTS NAME
1. Control Panel
10. Adjust Leg
2. Door Handle
11. Upper Rack
3. Front Cover
12. Cutlery Basket
4. Lower Cover
13. Detergent & Rinse Aid Dispenser
5. Process Monitor
14. Vapor Vent Cover
6. Power Switch
15. Upper Spray Arm
7. Drain Hose
16. Lower Spray Arm
8. Inlet Hose
17. Filter ASM
9. Power Cord
18. Lower Rack
The appearance and specifications may vary without notice.
9
FUNCTION OF CONTROL BUTTON
HALF LOAD
• In case of small load, use upper
or lower rack only to save
energy.
• With each press, can select
upper or lower rack only.
• In case you don’t select this
button, the machine always
works vario washing, which
operate upper and lower spray
arm alternately.
10
INDICATOR
• Refill with
rinse aid
• Child Lock
TIME LEFT
DELAY START
• Before starting, the display window shows the running time of
the selected program.
• After starting, the display window shows the remaining time.
• If the dishwasher has a trouble, the trouble type is displayed.
• If you want to delay the
start of selected program,
press this button before
pressing program button.
• Pressing this button will
increase time by 1 hour.
• The delay start time can be
adjusted from 1 hour to 19
hours.
If this error letters are displayed, please refer to the trouble
shooting guide page 20 and follow the guide.
“ ” : No error message (See page 17)
PROGRAM
CHILD LOCK
BEEP ON/OFF
POWER
• When you want to
select program, press
each button.
• Used to lock or unlock the
control buttons to prevent
all the setting from being
changed by a child.
• This function is
automatically canceled
when power failure occur.
• For locking/ unlocking,
press Intensive and
Eco 70° button for a few
seconds simultaneously.
• The dishwasher must be
switched on.
• The beep on/off function
can be set by pressing the
Intensive and Pre wash
button simultaneously for
a few seconds. Then, a
“on” will appear in the
time display.
• The beep on/off function
is automatically canceled
when power failure occur.
• For operating, press this
button first for power on.
• After operating, this
button automatically
switches off for safety and
energy saving.
• In case of irregular surge
disturbance to the
machine, the power may
be automatically turned off
for safety.
11
HOW TO USE AND OPERATE
1. Loading your Dishwasher
Be careful large items not to prevent the
detergent dispenser lid from opening
For the best washing performance, it is important that
the dishwasher is loaded according to instructions.
Before loading items into the dishwasher, you must
scrape off large particles in particular non soluble
items such as bones, toothpicks, pips, etc.
3. Using the Cutlery Basket
Cutlery should be mixed within each section of
the cutlery basket to prevent nesting of similar
items. Place the cutlery in the cover with the
handles down. The cover can be hinged and
clipped away from the basket if you choose not
to use them.
For the knives, place at seperate rack for knives
located at upper rack.
When loading the dishwasher, observe the following
general guidelines:
Position crockery such that water will contact all
surfaces.
Deep based items should be placed at an angle to
help water run off and dry properly.
Items with burnt on scraps should be soaked prior
to loading in the dishwasher.
Take care when loading and unloading
sharp items.
2. Loading the Lower Rack
The lower basket is best loaded with dinner plates,
soup bowls, dishes, pots, pans, lids and even the
grill tray.
Plates should be positioned upright and facing the
center of the rack.
Pots, pans and large dishes must be turned upside
down.
Take care not to obstruct the rotation of the
spray arms.
Dinner plate
Dessert plate
Soup plate
Dessert
plate
12
HOW TO USE AND OPERATE
4. Loading the Upper Rack
5. Adjusting the Upper Rack
The upper rack is best loaded with more
delicate items, small plates, long cutlery,
cups, glasses and dishwasher safe plastic
items. Plates should be positioned upwards
with the plate bottom facing the front of the
rack.
Cups, glasses and bowls must be positioned
upside down.
Extra cups or cooking utensils can be laid
on the fold down cup racks which may also
provide support for long stem glasses.
Take care not to obstruct the rotation of the
spray arm under the upper rack.
Your upper rack can be raised or lowered to
cater for different sized crockery. Before
adjusting, ensure that the rack is empty.
You can change the position of the upper
rack by lifting the rack upward, into the
upper position, or by pulling on the two
levers on either side of the rack to move it
down to its lower position.
We recommend that where possible the
upper rack remains level.
And when you pull the rack upward, hold
the middle location of the upper rack
(
marked position)
After adjusting the rack levels, check
that the spray arm is free to rotate.
Glasses
Knives
Cups
Saucers
Non Dishwasher Safe Items
The combination of high water temperatures and
dishwasher detergent may damage particular
items, therefore we do not recommend using the
dishwasher to wash the following:
WARNING
■ Copper or anodized aluminum
■ Hand painted silver or gold leaf crockery
■ Wood or bone handled utensils
■ Iron or non rust proof utensils
■ Plastic items which are not dishwasher safe.
Before adjusting, ensure rack is empty
of all crockery.
Otherwise crockery may be damaged or
you may be injured.
13
HOW TO USE AND OPERATE
6. Adding Detergent
Dispenser
Push latch to open
• Detergent must be put into the detergent
chamber before starting every program
except the Pre wash.
• Please follow the manufacturer’s
instructions printed on the manual when
determining the correct dosage.
• If your dishes are only moderately dirty,
you may be able to use less detergent than
recommended.
• Chambers hold 15g and 25g.
• The amount of detergent depends on the
program. Refer to the guide table.
PROGRAM
AMOUNT OF DETERGENT
Intensive
25g
Eco 70°
20g
Eco 50°
15g
Quick
10g
Pre wash
No detergent
Place proper
detergent into this
compartment
WARNING
The detergent used is a special
Dishwasher detergent and like all
household chemicals should be treated as
a poison and kept out of reach of children.
At completion of each wash program, the
detergent compartment should be checked
and any remaining detergent removed.
• After the detergent is supplied, the
chamber lid should be closed.
• The detergent is dispensed automatically
during the operation.
• The chamber lid remains open after
operation.
Detergent Information
Use only the detergent intended for
household dishwashers. (Ordinary handwashing detergent should not be used,
because the foam can interfere with proper
operation.)
14
HOW TO USE AND OPERATE
7. Adding Rinse Aid
Dispenser
For filling
To fill the Rinse Aid chamber, rotate the
round cap counter clockwise and remove.
Fill the container to the maximum level
with a good quality Rinse Aid, then replace
and lock the cap.
The Rinse Aid is automatically dispensed
during the final rinse cycle.
The dosage setting is factory set to suit
most installations. If, after washing, you
notice cloudy spots, streaks or water marks
on your glassware, it may be necessary
increase the setting. To do so, remove the
cap and rotate the indicator arrow to a
higher setting then replace the cap . If the
glasses are smeared or there is foam present
on the bottom of the glass or the bottom of
the machine. Select a lower setting.
For refilling
Depending on the dosage setting and the
number of washes, the chamber may need
only to be topped up once per month
approximately. The rinse aid level can be
checked by two methods.
• By the indicator window on the dispenser
when the dishwasher door is fully open.
● Black indicates sufficient Rinse Aid
O Clear indicates Rinse Aid required
• By the light on the control panel when the
dishwasher is working on.
Rinse Aid Information
Rinse Aid is necessary in order to get spot
and streak free dishes as well as improved
drying. Using the correct amount will
improve wash performance. However, using
too much can produce excess foam leading
to possible water leaks.
When the lamp is lit, it means the rinse aid
is almost empty. Refill the Rinse Aid
chamber as soon as possible.
15
HOW TO USE AND OPERATE
8. Fold down dividers
9. Separable basket
■ Fold-down dividers at the lower rack can
be lowered to improve stacking of pots
and pans.
■ Slide two baskets in opposite directions,
then pull them apart.
10. Drying
■ To assist drying, we recommend that the
door be fully opened after the cycle.
11. Energy Test
(AS / NZS 2007)
■ Appliance loaded in accordance with
standard specifications.
• Example of loaded dishwasher : p.12~13
• Capacity : 14 place settings
• Comparability course : Eco 50 Triple
Spray-Strong
• Rinse Aid setting : 3
• Reference cleaner : 6g of detergent onto
the inside surface of the door and fill 24g
into the detergent dispenser.
• Height-adjustable Rack-U must be
inserted into the uppermost position.
16
OPERATING SEQUENCE
Before starting, the display window shows
the running time of the selected program.
After starting, the display window shows
the remaining time.
The time in the display window will start
to decrease minute by minute.
If the door is opened during the program a
safety device ensures that the machine
stops.
Once the door is re-closed the program
will start from where it was interrupted.
Press the “Power” button
Check there is rinse aid
The corresponding indicator lights will
illuminate if refilling is required.
Open the door and check
the filters
Ensure they are clean and properly
positioned (See “User Maintenance
Instructions”).
At the end of the washing
program
Load the dishes
“
” is displayed on the digital display
and a buzzer sounds. The display then
shows “
” to indicate that the
dishwasher is in “Cool dry” mode.
Remove any excess food.
Pull the lower rack out and arrange the
dishes and cutlery.
Pull the upper rack out and arrange the
cups, glasses, etc.
Cool dry-“Cd”
This process is not part of the program.
At the end of the program, the fan will
continue to operate for about an hour to
diminish any remaining moisture.
If you want, you can now open and unload
the dishwasher.
Otherwise the dishwasher automatically
switches off for safety and energy saving
later.
CAUTION
Do not load the items in upper rack with
the lower rack is pulled out and loaded.
Ensure the spray arms can
freely rotate
Measure out detergent
CAUTION
Add the required amount of detergent into
the dispenser and close the lid.
Empty the lower rack first and then the upper
one. This will avoid water dripping from the
upper rack onto the dishes below.
Setting and starting the
program
WARNING
In general it is not advisable to open the door
while the machine is working.
If the door is opened, a safety device
ensures that the machine stops.
Care must be taken if the door is opened
during the hot phase or immediately after a
program has finished, as steam may escape.
Press the program button to select the
desired program.
After 3 seconds, the machine will start.
If necessary, select the option function
corresponding to the desired program.
The indicator lights of the program and all
the phases of the program will come on.
17
PROGRAM
According to the water temperature, pressure, voltage, running time may be varied.
Running time doesn’t contain “Cool dry - 60 min”.
Program
WASH
Pre Wash
50
Main
Wash
RINSE
Rinse 1
Rinse 2
Rinse 3
Heating
Rinse
70
70
60
70
40
50
70
70
DRY
Cool
dry
Intensive
Eco 70°
35
Eco 50°
Quick
Pre wash
Intensive Wash
Quick Wash
This program is ideal for very dirty
crockery, in particular pots, pans and
casserole dishes.
Can use for lightly soiled recently used
dishes and cutlery.
Eco 70° Wash
Pre wash
Can use this program for only removing
soil before washing dishes by hand.
This program is for heavily soiled.
Eco 50° Wash
This program offers the most efficient
energy and water consumption for a good
washing performance. It is recommended
that it will be used every time.
“Cool dry” is not part of the program.(See page 17)
Auto Restart
If the dishwasher is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
18
USER MAINTENANCE INSTRUCTIONS
To prevent trouble and poor operating, it is important to check and care for the
filters and spray arms at intervals.
Filters
Upper Spray Arm
• Remove the lower rack first.
• Turn the mesh filter counterclockwise off.
• Take out the mesh filter, upper STS filter
and outer filter.
• Clean them if necessary.
• Replace them in the reverse order.
• Pull the upper rack forwards.
• Check that the water jet holes are not
blocked by food particles.
• When necessary to clean, remove the arm
by unscrewing the nut.
• Clean the spray arm and replace it in the
reverse order.
Upper spray arm
Lower Spray Arm
• Check that the water jet holes are not
blocked by food particles.
• When necessary to clean, remove the arm
by pulling up.
• Clean the spray arm and replace it pulling
down.
19
TROUBLE SHOOTING GUIDE
■ If a problem occurs check below to see whether this can be solved.
■ In the unlikely event that the problem cannot be rectified, please contact
service engineer.
Problem
Possible Causes
The lamps do not come
on when the power switch on.
• Plug is not properly inserted in the socket.
• Fuse blown or circuit breaker tripped.
• The electricity of the house was cut off.
The machine does not start.
• Door is not fully closed.
• The start button is not pressed.
Water is not pumped away.
(The display show “
” code.)
• The drain hose is kinked.
• The filter is clogged. (Clean the filter.)
The display shows “
(Automatically Drain Pump operated.)
• Excessive water is supplied than normal water level.
• The inlet valve is troubled.
The display shows “
” code.
• Water is not supplied. (Water tap is not opened.)
The display shows “
” code.
• Water leakage in Hose connections.
• Water is leaked by damages.
The display shows “
” code.
• The circuit of Heater is troubled.
” code.
The spray arms does not rotate
smoothly.
• The mounting of spray arms is blocked by food
particles. (Clean the holes of the spray arm.)
White deposits are left on the
dish washer after washing.
• The amount of detergent or rinse-aid set incorrectly.
Streaks are left on glassware.
• Too little Rinse-aid dispensed.
Dry results are not satisfactory.
• Too little Rinse-aid dispensed.
Washing results are not
satisfactory.
• Incorrect amount of detergent.
• Utensils incorrectly arranged or overloaded.
• Filters are clogged.
• Water jet holes of spray arms blocked.
• Spray arms’ rotation obstructed by utensils.
• Unsuitable program selected.
The display shows “
”code.
• No error message.(See page 17.)
20
MEMO
21
MEMO
22
MEMO
23
P/No.: MFL30149757
Capacity
14 Place settings
Weight
52 kg
Power Supply
See rating label
Power Consumption
See rating label
Water Feed Pressure
50 ~ 800 kPa
Download PDF

advertising