LG | LW91105SS | LG LW91105SS Owner’s Manual

http://au.lge.com (Australia)
http://nz.lge.com (New Zealand)
Built In Oven
Installation and Operating Instructions
LW91105SS
To avoid the risk of accidents or damage to the OVEN,
it is essential to read these operating instructions
before it is installed or used for the first time.
And please keep this manual for later reference.
P/No.: MFL62060309
Contents
Instructions for safe and proper user ....................................... 3
1. Instructions for safe and proper use ....................................... 3
Instructions for the installer ...................................................... 5
2. Installation .............................................................................. 5
3. Description of controls ............................................................ 7
4. Use of the oven .................................................................... 12
5. Available accessories ........................................................... 13
6. Cooking hints ....................................................................... 14
Instructions for the user .......................................................... 20
7. Cleaning and maintenance .................................................. 20
8. Extraordinary maintenance .................................................. 22
INSTRUCTIONS FOR THE INSTALLER: these are intended for the
authorised person who must, install the appliance, set it
functioning and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for
cleaning and maintenance of the appliance.
2
Instructions for safe and proper user
1. Instructions for safe and proper use
This manual is an integral part of the appliance and therefore must
be kept in its entirety and in an accessible place for the whole
working life of the oven. We advise careful reading of this manual
and all the instructions therein before using the oven. Installation
must be carried out by qualified personnel in accordance with the
regulations in force. This appliance is intended for domestic uses
and conforms to current regulations in force. The appliance has
been built to carry out the following functions: Cooking and
heating-up of food. All other uses are considered improper.
The manufacturer declines all responsibility for improper use.
Do not leave the packing in the home environment. Separate the
various waste materials and take them to the nearest special
garbage collection centre.
It is obligatory for the electrical system to be grounded according to
the methods required by safety rules.
When linking up to mains by plug and socket, make sure that both
are compatible and connect by means of a power cable complying
with applicable regulations and power requirements.
The socket must be accessible after the appliance has been built in.
Never unplug by pulling on the cable.
Do not obstruct ventilation openings and heat dispersal slits.
Immediately after installation carry out a brief inspection test of
the oven, following the instructions below. Should the appliance
not function, disconnect it from the supply and call the nearest
technical assistance centre.
Never attempt to repair the appliance.
3
Instructions for safe and proper user
Always check that the control knobs are in the “ZERO” (OFF) position
when you finish using the oven.
Never put inflammable objects in the oven: They could be accidentally
lighted and cause fires.
During use the appliance becomes very hot. Take care not to touch the
heating elements inside the oven.
The I.D. plate with technical data, registration number and brand name
is positioned visibly on the oven door frame.
The plate must not be removed.
The use of this appliance is not permitted to people (including children)
of reduced physical and mental ability, or lacking in experience in the
use of electrical appliances, unless they are supervised or instructed by
adults or people responsible for their safety.
This appliance is designed for cooking food in a domestic application
and it shall not be used as a space heater.
Do not spray aerosols in the vicinity of this appliance while it is in
operation.
Before the appliance is put into operation, all the labels and protective
films applied inside or outside must be removed with the exception of
the rating I.D. label.
The manufacturer declines all responsibility for damage to
persons or things caused by non-observance of the above
prescriptions or by interference with any part of the appliance or by
the use of non-original spares.
4
Instructions for the installer
2. Installation
2.1 Electrical connection
Check that mains voltage and power cable ratings are as per the
indications provided on the label attached to the oven door frame.
This label must never be removed.
It is obligatory for the electrical system to be grounded according to
the methods required by safety rules.
If a plug and socket connection is being used make sure that the
plug and socket are compatible. Avoid use of adapters and shunts
as these could cause overheating and risk of burns. Extension
leads must not be used.
If a fixed connection is being used fit power line with an omnipolar
circuit breaker or isolation switch with a contact opening gap equal
to or greater than 3 mm in an easily accessible position in
proximity to the oven.
For operation on 230-240V~: use an
H05RR-F / H05V2V2-F type three-core
cable (3 x 1.5 mm2).
The cable end to be connected to the
appliance must be provided with an
ground wire (yellow-green) at least 20 mm longer.
The manufacturer declines all responsibility for damage to
persons or things caused by non-observance of the above
prescriptions or by interference with any part of the appliance.
5
Instructions for the installer
2.2 Mounting the oven
The oven is designed for mounting into any piece of furniture as
long as heat-resistant. Proceed according to the dimensions shown
in Figures 1, 2.
Fixing is carried out using 4 screws at the
corners “C” of the oven door frame, after
removing the side panels secured by the
screws “A” and the supports “B” as shown in
figure 3. To replace the side panels, take
care to engage the pins inside them
correctly with the supports “B”, then
retighten the screws “A”.
You are advised to use the side handles
provided in order to facilitate installation of
the appliance.
6
Before completely building in the oven, remove the side
handles which might cause unpleasant vibrations and noise
during normal operation of the oven.
Never use the oven door to lever the oven into
place when fitting.
Avoid exerting too much pressure on the oven
door when open.
The oven door should not be used as a resting
table for food being removed or put in to the oven.
3. Description of controls
3.1 Front control panel
All the oven controls are grouped together on the front panel.
FUNCTION SWITCH KNOB
Rotate the knob in either direction to select
desired function from the following:
7
Instructions for the installer
NO FUNCTION SET
UPPER AND LOWER
HEATING ELEMENT +
VENTILATION
OVEN LIGHT
UPPER AND LOWER
HEATING ELEMENT
DEFROSTING
WIDE GRILL ELEMENT
+ SPIT ROASTING
FUNCTION
WIDE GRILL ELEMENT +
VENTILATION + SPIT
ROASTING FUNCTION
THERMOSTAT KNOB
Cooking temperature is selected by
turning the knob clockwise to the
desired setting, between 50° and
250°C.
THERMOSTAT INDICATOR LIGHT
When this light comes on, the oven is heating up.
When this light goes out, the preset heating
temperature has been reached.
When the light turns on and off, the temperature
inside the oven is steady at the set temperature.
8
3.2 Electronic Programmer
The programmer user instructions are valid only for the main
oven.
LIST OF FUNCTIONS
MINUTE-COUNTER KEY
COOKING TIME KEY
END-OF-COOKING KEY
DECREASE TIME KEY
INCREASE TIME KEY
3.2.1 Clock adjustment
When using the oven for the first time, or after a power failure, the
display flashes regularly and indicates
. Press the keys ,
and at the same time the keys or : each single press changes
the time by 1 minute either up or down.
Before setting the programmer activate the desired function and
temperature.
9
Instructions for the installer
3.2.2 Semiautomatic cooking
Use this setting for automatic oven switch-off at the end of cooking
time. By pressing key , the display lights up, showing
; keep
the key pressed and at the same time, press keys or to set the
cooking time. Release key to start the programmed cooking time
count. The display will now show the right time together with
symbols A and .
3.2.3 Automatic cooking
Use this setting to automatically start and stop the oven. By
pressing key , the display lights up showing
; keep the key
pressed and at the same time, press keys or to set the cooking
time. By pressing key the sum of the right time + cooking time will
appear; keep the key pressed and at the same time, press keys
or to regulate the end of cooking time. Release key to start the
programmed count and the display will show the right time together
with symbols A and .
After set-up, to see the cooking time remaining, press the key ;
to see the end of cooking time press the key .
Set-up with incoherent values is logically prevented (e.g. the
contrast between a cooking time and a longer period will not be
accepted by the programmer).
3.2.4 End of cooking
When cooking is over, the oven will automatically switch off and, at
the same time, an intermittent alarm will sound. After switching off
the alarm, the display will once again show the right time together
with the symbol , indicating that the oven has returned to manual
operation mode.
10
3.2.5 Adjusting alarm volume
The acoustic alarm has three different settings. These can be
adjusted, while the alarm is off, by pressing key .
3.2.6 Switching off the alarm
The alarm switches off automatically after seven minutes. They can
be manually de-activated by pressing the keys and together.
3.2.7 Minute Counter
The programmer can also be used as a simple minute counter. By
pressing key
, the display shows
; keep the key pressed and
at the same time press keys or . On releasing the key
,
programmed counting will begin and the display will show the
current time and the symbol
.
After set-up, to see the remaining time, press the key
.
Use as a minute counter does not interrupt functioning of the
oven at the end of the programmed time.
3.2.8 Cancellation of set data
Once the programme has been set, keep the key of the function to
be cancelled pressed, while at the same time
is reached by
means of variation keys or . Time cancellation will be
considered as end-of-cooking time by the programmer.
3.2.9 Changing the set data
The cooking data entered can be changed at any time by keeping
the function key pressed and at the same time adjusting the keys
or .
11
Instructions for the installer
4. Use of the oven
Make sure that you have set a cooking time.
If the timer knob is on 0, no heating elements will come on.
4.1 Warnings and general advice
Before using the oven for the first time, pre-heat it to maximum
temperature (250°C) long enough to burn any manufacturing oily
residues which could give the food a bad taste.
During cooking, do not cover the bottom of the oven with
aluminium or tin foil and do not place pans or oven trays on it as
this may damage the enamel coating. If you wish to use
greaseproof paper, place it so that it will not interfere with the
hot air circulation inside the oven.
To prevent any steam in the oven creating
problems, open the door in two stages: half open
(5 cm approx.) for 4-5 seconds and then fully open.
To access food, always leave the door open as
short a time as possible to prevent the temperature
in the oven from falling and ruining the food.
4.2 Cooling system
The oven is equipped with a cooling system which automatically
comes on upon the oven being turned on.
Fans cause a steady outflow of air from above the
door which may continue for a brief period of time
even after the oven has been turned off.
12
4.3 Oven light
To turn on the oven light in models with static oven, rotate the
temperature knob clockwise to the first setting aligned with the lamp
symbol (
). The light will remain on throughout entire oven
operation.
5. Available accessories
The oven features 4 support positions for plates and
racks of different height.
Some models do not feature all accessories.
Grill: useful for holding cooking vessels.
Plate grill: for placing above plate for cooking
foods that might drip.
Oven plate: useful for catching fat from foods on the
grill above.
Pastry plate: for baking cakes, pizza and oven
desserts.
Roasting spit: useful for cooking chicken,
sausages and anything else requiring uniform
cooking over the whole surface.
Only for auxiliary oven.
Main oven rotisserie frame: to be fitted
into the holes provided in the oven dish.
Accessories available on request
Original accessories may be ordered from any Authorised
Service Centre.
13
Instructions for the installer
6. Cooking hints
In fan-assisted mode preheating should be carried out at
30/40°C above the cooking temperature. This considerably
shortens cooking times and reduces power consumption, as
well as giving better cooking results.
Keep the oven door closed during cooking
6.1 Traditional cooking (multifunction models)
This traditional cooking method, in which heat comes from
above and below, is suitable for cooking food on a single
level. You have to pre-heat the oven until the set
temperature is reached. Place the food in the oven only
after the thermostat indicator light has turned off. very fatty
meats may be put in when the oven is still cold. Put frozen
meat in immediately, without waiting for it to thaw. The only
precaution you need to take is to set the temperature about
20°C lower and cooking time about 1/4 longer than you
would for fresh meat.
14
6.2 Hot-air cooking (multifunction models)
This system is suitable for cooking on several levels,
including different types of food (fish, meat etc.), without
the tastes and smells mingling. Air circulation in the oven
ensures a uniform distribution of heat.
Multiple cooking is possible as long as the cooking temperature of
the different foods is the same.
6.3 Grill cooking
Permits rapid browning of foods. You are advised to place
the pan in the highest guide. For short-term cooking of
small quantities, place the grid in the fourth guide from the
bottom. For long-term cooking and grills, put the grid in the
lowest guide in accordance with the size of the pieces.
15
Instructions for the installer
6.4 Hot-air grilling (multifunction models)
Ensures uniform heat distribution with greater heat
penetration into the food. Food will be lightly browned on
the outside and remain soft inside.
Keep the oven door closed during cooking. Heating up
time must not exceed 60 minutes.
6.5 Defrosting (multifunction models)
The flow of air produced by the fan ensures quicker
defrosting.
The air circulating inside the oven is at room temperature.
The advantage of defrosting at room temperature is that it does not
alter the taste and appearance of the food.
16
6.6 Spit roasting (models with static oven)
Prepare the spit with the food, blocking fork screws A.
Insert frame B into the third guide from the bottom.
Remove handle D and position the spit shaft so that pulley
E is guided on the link of frame B in the right side. Insert
the drip tray into the oven as far as it will go until the tip of
the rod is in line with the hole C. Now rock the frames B to
insert the tip of the rod into the drive connection C of the
rotisserie motor on the side of the oven. Pour a bit of water
into the pan to avoid smoke from the dripping.
It is normal for the thermostat light to flash during cooking. This
indicates the temperature inside the oven is regular.
CAUTION: the frames B must be fitted
as shown in the diagram
17
Instructions for the installer
6.7 Recommended cooking table
Cooking times, especially meat, vary according to the thickness and
quality of the food and to consumer taste.
TRADITIONAL COOKING
LEVEL
FROM BELOW
TEMPERATURE
(°C)
TIME
IN MINUTES (*)
2
200
30-35
2
2
2
2
2
2
200
225
200
200
200
200
2
250
60-65
70-75
60-65
120-125
90-95
ACCORDING
TO DIMENSIONS
15-20
2
2
1
2
1
125
200
200
175
200
55-60
20-25
25-30
35-45
30-35
FIRST COURSES
OVEN-BAKED PASTA
MEAT
ROAST VEAL
ROAST PORK
CHICKEN
DUCK
RABBIT
FISH
PIZZA
DESSERTS
MERINGUES
BISCUITS
PASTRY
SPONGE CAKE
FRUIT PIE
(*) = WITH PREHEATED OVEN
GRILLING
LEVEL
FROM BELOW
TOAST
CHICKEN
FISH
TOMATOES OR
ZUCCHINIS
TIME IN MINUTES
3
3
3
FIRST SURFACE
5
30
18
SECOND SURFACE
5
30
18
3
8
8
18
HOT-AIR COOKING
FIRST COURSES
OVEN-BAKED PASTA
MEAT
ROAST VEAL
ROAST PORK
CHICKEN
DUCK
RABBIT
FISH
PIZZA
DESSERTS
MERINGUES
BISCUITS
PASTRY
SPONGE CAKE
FRUIT PIE
LEVEL
FROM BELOW
TEMPERATURE
(°C)
TIME
IN MINUTES
2
175
30-35
2
2
2
2
2
2
175
200
200
175
175
175
2
225
60-65
70-75
60-65
120-125
90-95
ACCORDING
TO DIMENSIONS
15-20
2
2
1
2
1
125
175
175
175
175
55-60
20-25
25-30
35-45
30-35
19
Instructions for the user
7. Cleaning and maintenance
Never use a steam jet to clean the appliance.
Before performing any operations requiring access to powered
parts, switch off the power supply to the machine.
7.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned
regularly after use. Let it cool first.
7.1.1 Ordinary Daily Cleaning
To clean and preserve the stainless steel surfaces, always use only
specific products that do not contain abrasives or chlorine-based
acids.
How to use: pour the product on a damp cloth and wipe the
surface, rinse thoroughly and dry with a soft cloth or chamois.
7.1.2 Food stains or residues
Do not use metallic sponges or sharp scrapers: they will
damage the surface.
Use normal non-abrasive products for steel, and a wooden
or plastic tool if necessary.
Rinse thoroughly and dry with a soft cloth or deerskin.
Do not allow residues of sugary foods (such as jam) to set inside
the oven. If left to set for too long, they might damage the enamel
lining of the oven.
20
7.2 Cleaning of the oven
For best oven upkeep clean regularly after having allowed to cool.
Take out all removable parts.
• Clean the oven grill and side guides with hot water and nonabrasive detergent. Rinse and dry.
• The oven should be operated at the maximum temperature for
about 15/20 minutes after using specific products, to eliminate the
residues deposited inside the oven.
• For easier cleaning, the door can be removed (see P. 8.2)
7.3 Door glass
The door glass should always be kept clean. Use absorbent kitchen
paper to clean. In case of tough spots, clean with a damp sponge
using regular detergent.
Do not use metallic sponges or sharp scrapers: they will
damage the surface.
21
Instructions for the user
8. Extraordinary maintenance
The oven may require extraordinary maintenance or replacement of
parts subject to wear such as seals, bulbs, and so on. The following
instructions describe how to carry out these minor maintenance
operations.
Before any intervention, disconnect the power supply of the
device.
8.1 Replacement of light bulb
Remove the bulb protector A by turning anticlockwise and change
bulb B (in the 8-function model with front glass panel change the
halogen bulb C) with a similar one. Re-fit the bulb protector A.
Only use oven bulbs (T 300°C) 25W.
22
8.2 Removing
Hold the door on both sides with both hands near hinges A and
raise levers B. Lift up the door forming an angle of about 45° and
remove. To refit, slide the hinges A in the grooves, drop the door
and release levers B.
8.3 Oven door seal
To permit thorough cleaning of the oven, the seal
may be removed. Before removing the seal, take off
the door as described above. Once the door has
been taken off, lift the tabs at the corners as shown
in the figure.
After cleaning, refit the seal with the longer side
horizontal and insert the tabs into the appropriate
holes starting from the top ones.
23
FOR WARRANTY SERVICE PLEASE CONTACT
LG Service on 1300 LG CARE (1300 54 2273) AUSTRALIA or
0800 LG CARE (0800 54 2273) NEW ZEALAND
LG Electronics Australia
2 Wonderland Drive
Eastern Creek NSW 2766
(ABN : 98 064 531 264)
LGEAP
Download PDF

advertising