LG | LD-1426T | LG LD-1426T Owner’s Manual

DISHWASHER
OWNER'S MANUAL
MODEL
:
LD-1426T
Please read this manual
carefully
before
operating your
dishwasher. Retain it for future reference.
CONTENTS
SAFETY AND CAUTION
3
INSTALLATION INSTRUCTIONS
5
PARTS NAME
9
FUNCTION OF CONTROL BUTTON
10
HOW TO USE AND OPERATE
12
OPERATING
18
SEQUENCE
PROGRAM
19
USER MAINTENANCE INSTRUCTIONS
20
TROUBLE SHOOTING GUIDE
21
SPECIFICATION
SAFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING
?
-
Please read this manual
before
using
using your dishwasher, follow
including the following:
When
carefully
During
the dishwasher for the first
?
time.
?
This manual contains very important
notes regarding the installation, use and
The manufacturer
can
not be
This dishwasher is
household
?
Do not
designed
cause
is
?
?
label.
rating
only guaranteed
when the earth system of your house is
in accordance with the related local
regulations.(Do
cable
?
or
not
use an
?
cord.)
65ºC, adjust
the water heater
If the hot water
setting.
temperature can not be maintained
below 65ºC, the dishwasher must be
If power
must
supply cord is damaged,
only be replaced by the
manufacturer
it
its service agent or
similar qualified person in order to
avoid
?
a
or
sit
the inner
on
It may
failure of your
opened.
the deformation
or
Do not
use
the
detergent for hand
washing.
The detergent for dishwasher should be
used for normal operation.
This appliance is fitted with a safety
function that automatically stops the
operation of the dishwasher when it is
exposed to heavy disturbance on its
Dishwasher
detergents are strongly
alkaline. They can be extremely
dangerous if swallowed. Avoid contact
with skin and eyes and keep children
empty after completion of the wash
cycle.
a
?
Some pre-treatment sprays
or
liquids
damage your dishwasher’ s control
panel and plastic components, so do not
can
hazard.
This
appliance must be positioned so
plug is accessible.
The appliance is to be connected to the
water mains using new hose-sets and
use
that the
?
or
away from the dishwasher when the
door is open.
Check that the detergent receptacle is
connected to cold water.
?
down
mains.
extension
If the hot water exceeds
push
dishwasher.
Electrical connection must be in
safety
electric shock.
door when the door
installation
Electrical
cause an
Do not
or
young children or infirm persons
without supervision.
?
may
fire.
?
the dishwasher for industrial
accordance with the
They
or
Do not spray water on the appliance.
It may cause the failure of electric parts
and commercial use, or other purpose.
The appliance is not intended for use
During
any kinds of solvent in your
use
?
for normal
use.
use
Do not
explosion
by
?
Only suitable household utensils should
placed in the dishwasher.
(Please avoid utensils; that are non-
dishwasher.
instructions.
?
use
heartresistant, metal decorated, etc.)
?
responsible for problems caused by
ignoring these safety and caution
?
precautions,
be
maintenance of your dishwasher.
?
basic
these
products
on or
around your
dishwasher.
?
Be careful! Water could be
when door is
that old hose-sets should not be reused.
3
opened.
splashed
out
SAFETY AND CAUTION
Child
?
?
?
?
Safety
Controls may be locked
using
"Child Lock" mode to prevent from
dishwasher
accidentally.
Keep children
away from detergents and rinse-aids.
Do not allow children to operate the dishwasher.
Young
children should be
CAUTION
supervised
concerning
to
ensure
that
they
do not
play
with the
appliance.
the Power Cord
appliances recommend they be placed upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to be certain.
?
Most
?
Do not overload wall outlets. Overloaded wall
outlets, loose
damaged wall outlets,
are dangerous.
cords, frayed power cords,
damaged
Any of these conditions could result in electric shock or fire. Periodically examine the cord
of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and
the point where the cord exits the appliance.
extension
?
starting
or
or
or
cracked wire insulation
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and grounded in accordance
This
with all local codes and ordinances.
WARNING
-
connection of the
equipment-grounding conductor can
a qualified electrician or
service representative if you are in doubt whether the appliance is
properly grounded. Do not modify the plug provided with the
appliance; if it will not fit the outlet have a proper outlet installed by
a qualified electrician.
Improper
result in
a
risk of electric shock. Check with
4
INSTALLATION INSTRUCTIONS
Step2:
WARNING
PREPARE ELECTRICAL WIRING
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
CAUTION
For
personal safety, remove house fuse
open circuit breaker before installation.
Do not use an extension cord or adapter
plug with this appliance. Electrical and
grounding connections must comply with
the national electrical code/provincial and
municipal code and/or other local codes.
or
Step1:
PREPARE CUPBOARD OPENING
This dishwasher is
1
size shown
2
Select
as
location
a
possible
designed
to fit to the
below.
as
close to sink
1
on
an
The dishwasher should not be installed
more
circuit breaker
than 3 meters from sink for proper
Wiring
drainage.
4
If dishwasher is to be installed in
a
2
corner,
minimum 5cm of space is required
between the washer and an adjacent
a
cabinet
or a
appliance must be supplied with
rating voltage and hertz as shown
instruction manual, and connected to
individual, properly grounded branch
circuit, protected by minimum 15 amp
for easy connections to water and
drain lines.
3
This
correct
as
or
time
must be 2
delay
wires with
fuse.
ground.
The power plug must be in a accessible
location adjacent to and not behind the
dishwasher and within 1.2 meters of the
dishwasher
wall.
3
side.(See
page 7
The power plug must be correctly
earthed, if in doubt, have it checked
qualified Electrician.
plug.
If bare chipboard is adjacent to or above
the dishwasher, it should be sealed with a
waterproofing paint or sealant to prevent
swelling due to steam.
5
by
a
double
by a
appliance
same plug
No other
should be connected to the
outlet
Unit:mm
Fig.A)
adapter
or
similar
INSTALLATION INSTRUCTIONS
Step3:
Step4:
PREPARE DISHWASHER FOR
INSTALL THE DISHWASHER IN
INSTALLATION
CUPBOARD
the dishwasher
1
Lay
2
Adjust
the
cabinet
as
legs
on
its back.
to the needed
shown in below
height
figure.
Before
sliding the dishwasher into the
cupboard opening, all necessary final
height adjustment and balancing adjustment
should be done using the spanner.
1
of
2
Slide the dishwasher into the cabinet
opening carefully.
Make
sure
that the
drain hose inside the cabinet is not
kinked
or
stretched.
CAUTION
If the height of cupboard is below 850mm, you
should remove the top table by unscrewing
the 2 screws. (Two of rear)
6
INSTALLATION INSTRUCTIONS
Step5:
DRAIN LINE CONNECTION
1
If the end of drain hose does not fit to
the drain line,
■ When the drain hose is connected
of rubber
piece
connector(not supplied) that must be
resistant to heat and detergent and may
be obtained from a plumbing shop.
2
There
are
shown in
use a
2
typical connections
Figure A, B.
to a
separate stand pipe, it is essential that
air tight connection is made.
Refer to
an
Fig.B
as
The "S" trap spigot must be drilled out
cleanly and free of obstruction to its
maximum internal diameter, if used for
drainage.
To prevent siphoning, one of the following
instruction methods must be followed:
■ When the drain hose is connected
to a
sink "s" trap or waste disposal unit, the
hose must be looped up to the underside
Fig.
B
:
Drainage
connection
-
stand
pipe.
of the bench top and secured.
Drain Hose Extension
Extend Drain Hose
Fig.
as
shown below.
A
CAUTION
When you connect or extend Drain Hose,
make sure that drain hose is not kinked.
(Bends should have 40 mm radius.)
7
INSTALLATION INSTRUCTIONS
Step6:
Step8:
WATER SUPPLY CONNECTION
HOW TO LEVEL THE PRODUCT
1
Connect the water
supply hose to the
tap
figure.(Some
models consist of an inlet valve and hose.)
After
This dishwasher may be fed with either
hot or cold water. If the water can not be
close the door, you have to
product.
maintained below 65ºC, the dishwasher
must be connected to cold water.
Case 1. In
water
2
as
shown in
installing
hear
sticky
side portion
or
a
the
product, if you feel some
frictional sound between the
of door and tub when you open or
adjust the level of
case
the door is slanted to the
connecting, the sealing tape or
sealing compound should be used to avoid
right
When
Slant to
the right
water leaks.
Make
sure
sharply
that the line is not kinked
DOOR
or
bent.
Fig. C
Water tap
Water
hose
?
supply
?
If the door is slanted to the
right as shown in
figure C, repeat the procedure shown as below
until the door is operated normally.
1) Unscrew(counter-clockwise) the left leg of
back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
When the product is correctly leveled, there do
not remain
Case 2. In
Step7:
slant, stickiness
case
or a
friction sound.
the door is slanted to the left
Slant to
the right
FINAL CHECK AND ASSEMBLING
DOOR
1
2
Securely hand tighten supply hose to
water supply.
Plug power supply cord into an
earthed the power plug and switch on.
After
installing
Fig.
?
the
product, operate
the dishwasher through one cycle
(Quick cycle is recommended) without
loading the dishes.
Through this, you can check for water
leak and operating conditions.
When you operate the product the
D
If the door is slanted to the left
as
shown in
figure D, repeat the procedure shown
until the door is operated normally.
1) Unscrew(counter-clockwise)
back side and
high
2) Check the opening
the
as
below
right leg
of
the level.
of door if there still
remains
?
first, the noise may be occurred.
sticky or friction sound.
When the product is correctly leveled,
not remain
In that case, turn off power switch and
restart the dishwasher.
8
slant, stickiness
or a
there do
friction sound.
PARTS NAME
1. Control Panel
10.
Adjust Leg
2. Handle deco
11.
Upper
3. Door Handle
12.
Cutlery
4. Front Cover
13.
Detergent
5. Lower Cover
14.
Vapor
6. Power Switch
15.
Upper Spray
7. Drain Hose
16. Lower
8. Inlet Hose
17. Filter ASM
9. Power Cord
18. Lower Rack
※ The appearance and
specifications
Rack
Basket
& Rinse Aid
Vent Cover
Spray
may vary without notice.
9
Arm
Arm
Dispenser
FUNCTION OF CONTROL BUTTON
INDICATOR
?
:
Child lock
?
:
Refill with Rinse aid
CHILD
EXTRA HOT
LOCK
/ RINSE+
unlock the
With each press,
77
extra hot,
control buttons
Rinse+,
prevent all
the setting from
hot & Rinse+ is
Used to lock
or
to
?
?
being changed
by a child.
For locking /
unlocking, press
?
77
extra
TIME LEFT
?
?
?
repeated.
?
?
Before
starting,
the
selected program.
After starting, the
display window
display
window shows the
running time of the
remaining time.
If you select "Auto" program, the "F" is displayed, it means that the
sensor is sensing the status of the dishwasher. When the optimum
program is selected by sensor, the remaining time is displayed.
If the course time is over 100 minutes, the "2H" is displayed.
If the dishwasher has
:
Drainage
a
trouble, the trouble type is displayed.
trouble
:
Problem of
button
:
Water inlet trouble
simultaneously.
:
Water
:
Heater trouble
Auto and Quick
shows the
10
overfilling
leakage
trouble
water
If this error letters are displayed,
please refer to the trouble shooting
guide page 21 and follow the guide.
TRIPLE
PROGRAM
?
TIME DELAY
SPRAY
When you want to select
program, press each
?
button.
With each press, the level
of water jet is changed to
"Strong", "Medium",
?
and
If you want to delay the start of
selected program, press this button
before start.
"Soft".
?
?
Pressing this button will increase
time by 1 hour.
The delay start time can be adjusted
from 1 hour to 19 hours.
HALF LOAD
?
In
case
upper
save
?
?
of small
or
load,
lower rack
BEEP ON / OFF
use
only
to
?
The dishwasher must be switched
?
The
energy.
With each press, can select
upper or lower rack only.
In
case
button,
you don't select this
the machine always
works vario
washing,
which
operate upper and lower spray
arm
on.
a
can
alternately.
?
?
After
?
the Half
Load button.
?
For
"on" will appear in the time
display.
To change the setting, press
operating, press this
button first for power on.
?
be set
beep
by
pressing the Half Load and Power
button simultaneously for seconds,
then
?
on/off function
POWER
operating, this button
automatically switches off for
safety and energy saving.
In case of irregular surge
disturbances to the
machine,
Then press the Rinse button to
the power may be
automatically turned off for
activate
safety.
setting.
beep on/off function is
automatically canceled when power
The
failure
occur.
11
HOW TO USE AND OPERATE
1.
For the best
Be careful
large items not to prevent
the detergent dispenser lid from
opening
Dishwasher
Loading your
washing performance,
it is
that the dishwasher is loaded
important
according to instructions.
Before loading items into the dishwasher,
you must scrape off large particles in
particular non soluble items such as bones,
toothpicks, pips, etc.
loading the dishwasher,
following general guidelines:
observe the
■ Position crockery such that
water will
When
3.
Cutlery
nesting
the
2.
prior
off and
and
facing
the Lower Rack
soup bowls, dishes, pots, pans, lids
the grill tray.
positioned upright
upside
and
the center of the rack.
must be turned
down.
Take care not to obstruct the rotation
of the spray arms.
Dinner Plates
Soup
Plates
Dessert
dishes
care
sharp
on
Pots, pans and large dishes
cutlery
with the handles down. The
in
cover
knives located at upper rack.
at an
even
Plates should be
basket to prevent
dry
The lower basket is best loaded with dinner
plates,
Basket
be hinged and clipped away from the
basket if you choose not to use them.
For the knives, place at seperate rack for
scraps should be
to loading in the dishwasher.
Loading
cutlery
of similar items. Place the
cover
Take
■ Items with burnt
soaked
run
Cutlery
can
■ Deep based items should be placed
water
the
should be mixed within each
section of the
contact all surfaces.
angle to help
properly.
Using
Saucers
Dessert
dishes
12
when
items.
loading
and
unloading
HOW TO USE AND OPERATE
4.
Loading
the
5.
Upper Rack
Adjusting
the
Upper
Rack
The upper rack is best loaded with more
delicate items, small plates, long cutlery,
Your upper rack can be raised or lowered to
cater for different sized crockery. Before
cups, glasses and dishwasher safe plastic
items. Plates should be positioned upwards
adjusting, ensure that the rack is empty.
can change the position of the upper
rack by lifting the rack upward, into the
upper position, or by pulling on the two
with the
plate
bottom
facing
You
the front of the
rack.
Cups, glasses
upside down.
and bowls must be
levers
positioned
After
Dessert dishes
Cups
Knives
it
possible
the
upward,
hold
the middle location of the upper rack
marked position)
(
under the upper rack.
Glasses
move
position.
upper rack remains level.
And when you pull the rack
provide support for long stem glasses.
Take care not to obstruct the rotation of the
arm
either side of the rack to
We recommend that where
Extra cups or cooking utensils can be laid
on the fold down cup racks which may also
spray
on
down to its lower
adjusting
that the spray
the rack
arm
levels, check
is free to rotate.
Saucers
Non Dishwasher Safe Items
The combination of high water temperatures and
dishwasher detergent may damage particular
items, therefore
we
do not recommend
dishwasher to wash the
using
the
following:
WARNING
anodized aluminum
Copper
Hand painted
or
Wood
Iron
or
silver
or
Before adjusting, ensure rack is empty
of all crockery.
Otherwise crockery may be damaged or
you may be injured.
gold leaf crockery
bone handled utensils
or non
rust
proof utensils
Plastic items which
are
not
dishwasher safe.
13
HOW TO USE AND OPERATE
6.
?
Adding Detergent
Dispenser
Detergent
must be
chamber before
Push latch to open
put into the detergent
starting
every program
except the Pre-Wash.
?
?
Please follow the manufacturer's
instructions
printed on
determining
the correct
the manual when
dosage.
Place proper
detergent into this
If your dishes are only moderately dirty,
you may be able to use less detergent than
recommended.
?
Chambers hold
?
The amount of
compartment
and
15g
25g.
detergent depends on
guide table.
the
program. Refer to the
PROGRAM
AMOUNT OF DETERGENT
Intensive
25g
Auto
20g
Eco
15g
Gentle
10g
Quick
10g
Pre-Wash
?
After the
No
detergent
is
WARNING
The detergent used is a special
Dishwasher detergent and like all
household chemicals it should be
treated as harmful and kept out of reach
of children. After completion of the wash
program, the detergent compartment
detergent
supplied,
should be checked and any
detergent removed.
the
chamber lid should be closed.
?
The
detergent is dispensed automatically
during the operation.
?
The chamber lid remains open after
operation.
Detergent
Use
only
the
Information
detergent
intended for
household dishwashers.
washing detergent
because the foam
(Ordinary hand-
should not be used,
can
interfere with proper
operation.)
14
remaining
HOW TO USE AND OPERATE
7.
Adding Rinse
Dispenser
?
For
Aid
filling
To fill the Rinse Aid
chamber,
rotate the
round cap counter clockwise and remove.
Fill the container to the maximum level
with
a
good quality
and lock the cap.
The Rinse Aid is
during
The
Rinse Aid, then
replace
automatically dispensed
cycle.
the final rinse
dosage setting
is
factory
set to suit
most installations.
If, after washing, you
notice cloudy spots, streaks or water marks
your glassware, it may be necessary
increase the setting. To do so, remove the
on
cap and rotate the indicator
arrow to a
higher setting then replace the cap. If the
glasses are smeared or there is foam present
on the bottom of the glass or the bottom of
the machine. Select a lower setting.
?
For
refilling
Depending
on
the
dosage setting
and the
number of washes, the chamber may need
only to be topped up once per month
approximately. The rinse aid level can be
by two methods.
the
indicator window on the dispenser
By
when the dishwasher door is fully open.
checked
?
Rinse Aid Information
Black indicates sufficient Rinse Aid
O
?
Clear indicates Rinse Aid
By
the
light
on
dishwasher is
the control
working
required
panel
Rinse Aid is necessary in order to get spot
and streak free dishes as well as improved
when the
drying. Using the correct amount will
improve wash performance. However, using
too much can produce excess foam leading
to possible water leaks.
on.
When the
) is lighted on, it means the
lamp (
rinse is almost exhausted. Then,
15
refill the Rinse.
HOW TO USE AND OPERATE
9. Removable Rack
8. Fold down dividers
Fold-down dividers at the lower and the
A removable rack at the lower rack is
upper rack can be lowered to
stacking of pots and pans.
detachable for
improve
10. Glass
A
loading pots
and pans.
supporter
glass supporter can be folded down to
arrange glasses and cups easily on the
upper rack.
16
HOW TO USE AND OPERATE
11.
Separable
Slide two baskets in
then
pull
basket
12.
opposite directions,
Drying
At the end of the program, it is
fully open the door to
them apart.
recommended to
assist in
13.
①
②
②
?
?
?
?
①
?
?
17
drying.
Energy Test(AS/NZS 2007)
Appliance loaded in accordance with
standard specifications.
Example of loaded dishwasher : p.12~13
Capacity : 14 place settings
Comparability course : Eco 50℃ with
option rinse+
Rinse aid setting : 3
Reference cleaner : 6g of detergent onto
the inside surface of the door and fill 24g
into the detergent dispenser.
Height-adjustable Rack-U must be
inserted in the uppermost position.
OPERATING SEQUENCE
Open the door and Press
the "power" button
The indicator
When you press the "power" button, the
state of default program being set will be
Before
displayed.
To start, close the door.
Check that there is rinse
one
the
phases
come on.
the
starting, the display window shows
running time of the selected program.
Select if necessary the washing on only
rack by pressing the half load button.
Remember to load all dishes into
aid
The
corresponding indicator lights
illuminate if refilling is necessary.
the selected rack.
will
The time in the
Ensure
they are
positioned (See
Instructions").
clean and
a
At the end of the
operating, buzz sound informs you
that the program has ended and the
dishwasher automatically switches off for
safety
CAUTION
and energy
Do not load the items in upper rack with
the lower rack is pulled out and loaded.
Ensure that the spray
Empty the lower rack first and then the
upper one; this will avoid water dripping
from the upper rack onto the dishes in the
lower one.
freely
WARNING
detergent
required amount of detergent
dispenser. Close the detergent
dispenser lid.
In general it is not advisable to open the
door while the machine is working;
If the door is opened however, a safety
device ensures that the machine stops.
Care must be taken if the door is opened
during the hot phase or immediately after
a program has finished, as steam may
into
the
and
starting
the
program
course
corresponding
escape.
button to select the
program.
If necessary, select the
option
saving.
CAUTION
arms
Add the
washing
After
Pull the upper rack out and arrange the
cups, glasses, etc. in it.
Setting
of the
that the
program
in it.
Measure out
run
interrupted.
Remove any scraps of food.
Pull the lower rack out and arrange the
can rotate
opened during the
safety device ensures
program
machine stops.
Once the door is closed the program will
start from the point where it was
properly
"User Maintenance
cutlery
window will start
If the door is
Load the dishes
dishes and
display
to decrease from minute to minute.
Check the filters
Push the
lights of the program and all
the program consists of will
function
to the desired program.
18
PROGRAM
WASH
Program
Pre Wash
50
Main
Wash
RINSE
Rinse 2
Rinse 1
Rinse 3
70
DRY
Heating
Rinse
70
Intensive
The program sequence is optimized and adapted in accordance
with how dirty the dishes are.
Auto
40
50
40
50
35
40
Eco
Gentle
Quick
Pre-Wash
Intensive Wash
Eco Wash
This program is for very heavily soiled
loads including pots, pans and casserole
dishes which may have
dry
This program is for
food residue.
This program is for
like glasses.
During the Auto program, the degree of
soiling in the dishes is determined by the
amount of clouding of the water.
According the degree of soiling, the
program automatically adjust the washing
time, temperature, level of water jet, the
result, the energy and
to the
delicate items
cutlery.
water
turbidity of the water,
washing
Quick Wash
Pre-Wash
consumption is kept as low as possible.
The "F" on display means that the sensor
is sensing the status of the dishwasher.
According
everyday loads.
This program is for that quick wash of
lightly soiled recently used dishes and
number of rinse.
a
soiled
Gentle Wash
Auto Wash
As
light
Can
use
this program for only removing
washing dishes by hand.
soil before
the drain
Intensive, Auto and Gentle program.
19
course
may be deleted after pre-wash
on
USER MAINTENANCE INSTRUCTIONS
To prevent trouble and poor operating, it is
arms at intervals.
important
to check and care for the
filters and spray
Upper Spray Arm
Filters
?
Remove the lower rack first.
?
?
Turn the mesh filter counterclockwise off.
?
?
Take out the mesh filter, upper STS filter
and outer filter.
?
?
Pull the upper rack forwards.
Check that the water jet holes
blocked
?
Clean them if necessary.
Replace them in the reverse order.
?
?
Check that the water jet holes
blocked
?
Spray Arm
by
food
are
not
remove
the
particles.
When necessary to clean,
arm
by pulling up.
?
Clean the spray
down.
arm
and
replace
it
pulling
20
food
Clean the spray
order.
are
not
remove
the
particles.
When necessary to clean,
by unscrewing the nut.
reverse
Lower
by
arm
and
replace
arm
it in the
TROUBLE SHOOTING GUIDE
If
problem occurs check
In the unlikely event that
service engineer.
a
the
whether this
see
problem
cannot be
be solved.
can
rectified, please
contact a
Possible Causes
Problem
The
below to
do not
is not
Plug
?
Fuse blown
?
The
The machine does not start.
?
Door is not
Water is not
?
The drain hose is kinked.
code.)
?
The filter is
code.
?
Excessive water is
?
The inlet valve is troubled.
?
Water is not
?
Inlet valve is blocked
?
Water
?
Water is leaked
?
The circuit of Heater is troubled.
?
The
mounting of spray arms is blocked by food
particles. (Clean the holes of the spray arm.)
?
The amount of
?
Too little Rinse-aid
dispensed.
?
Too little Rinse-aid
dispensed.
?
Incorrect amount of
come
when the power switch
pumped
away.
(The display show
"
"
The
"
"
shows
display
(Automatically
The
The
The
display
display
display
The spray
Drain
on.
Pump operated.)
shows
shows
shows
"
"
"
"
"
"
code.
code.
code.
does not rotate
arms
smoothly.
White
deposits
are
dish washer after
Dry
left
on
results
are
not
Washing results
satisfactory.
on
the
circuit breaker
or
of the house
electricity
fully
tripped.
was
cut
off.
closed.
the
clogged. (Clean
supplied
filter.)
than normal water level.
supplied. (Water tap is not opened.)
by safety device for leakage sensing.
in Hose connections.
leakage
by damages.
detergent
or
rinse-aid set
incorrectly.
washing.
are
Streaks
left
properly
inserted in the socket.
?
on
lamps
glassware.
satisfactory.
are
not
?
?
?
?
?
detergent.
incorrectly arranged or overloaded.
Filters are clogged.
Water jet holes of spray arms blocked.
Spray arms'rotation obstructed by utensils.
Utensils
Unsuitable program selected.
21
MEMO
22
MEMO
23
Capacity
14 Place
Weight
See
rating
label
Power
Supply
See
rating
label
Power
Consumption
See
rating
label
Water Feed Pressure
P/No.: 3828DD3008Y
50
settings
800 kPa
~
Download PDF