LG | LD-14AW3 | LG LD-14AW3 Owner’s Manual

DISHWASHER
OWNER'S MANUAL
MODEL
:
LD-14AW3
Please read this manual
carefully
before
operating your
dishwasher. Retain it for future reference.
CONTENTS
SAFETY AND CAUTION
3
INSTALLATION INSTRUCTION
5
PARTS NAME
9
FUNCTION OF CONTROL BUTTON
10
HOW TO USE AND OPERATE
11
WASH OPTIONS
16
PROGRAMS
17
CHECK AND CARE
18
TROUBLE SHOOTING GUIDE
19
SPECIFICATIONS
SAFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING
?
Please read this manual
using
?
?
-
using your dishwasher, follow
including the following:
When
carefully before
During
the dishwasher for the first time.
?
This manual contains very important notes
regarding the installation, use and
maintenance of your dishwasher.
The manufacturer can not be responsible
?
problems caused by ignoring these
safety and caution instructions.
This dishwasher is designed for normal
household
?
?
Do not
?
Do not
any kinds of solvent in your
use
They may
cause an
explosion
fire.
Do not spray water on the appliance.
It may cause the failure of electric parts
or
electric shock.
and commercial use, or other purpose.
The appliance is not intended for use by
or
Only suitable household utensils should be
placed in the dishwasher.
(Please avoid utensils; that are non-
or
the dishwasher for industrial
young children
use
dishwasher.
use.
use
precautions,
heatresistant, metal decorated, etc.)
for
?
basic
?
infirm persons without
push down or sit on the inner door
when the door opened. It may cause the
Do not
deformation
supervision.
?
Do not
use
failure of your dishwasher.
the detergent for hand washing.
or
The
During
?
installation
Electrical connection must be in
?
accordance with the
?
Electrical
safety
is
rating label.
only guaranteed when
the earth system of your house is in
accordance with the related local
regulations.(Do not use
or
?
If the hot water exceeds
setting.
65ºC, adjust
the
?
Do not expose skin to vapor vent. During
operation, as hot steam may scald.
not be maintained
below
?
Dishwasher
must be connected to
alkaline.
detergents are strongly
They can be extremely dangerous
cold water.
if swallowed. Avoid contact with skin and
If power
eyes and keep children away from the
dishwasher when the door is open.
supply cord is damaged, it must
only be replaced by the manufacturer or its
service agent or a similar qualified person
in order to avoid
?
vapor vent. It may cause the failure of
mechanical parts and noise.
If the hot water
temperature
65ºC, the dishwasher
can
?
extension cable
cord.)
water heater
?
an
?
detergent for dishwasher should be
used for normal operation.
This appliance is fitted with a safety
function that automatically stops the
operation of the dishwasher when it is
exposed to heavy disturbance on its mains.
Do not insert anything such as coin into the
This
a
Check that the
hazard.
must be
that
appliance
positioned
the plug is accessible.
The appliance is to be connected to the
water mains using new hose-sets and that
so
?
old hose-sets should not be reused.
3
detergent receptacle is
empty after completion of the wash cycle.
Some pre-treatment sprays or liquids can
damage your dishwasher's control panel
and plastic components, so do not use these
products on or around your dishwasher.
SAFETY AND CAUTION
Child
Safety
?
Controls may be locked
changed by a child.
?
children away from detergents and rinse-aids.
Do not allow children to operate the dishwasher.
?
?
?
?
"Child Lock" mode to prevent from all the
setting
from
being
Keep
Young
children should be
CAUTION
?
using
supervised to
concerning
ensure
that
they
do not
play
with the
appliance.
the Power Cord
they be placed upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire. Periodically examine the cord
of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and
the point where the cord exits the appliance.
Most
appliances
recommend
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and grounded in accordance
This
with all local codes and ordinances.
WARNING
-
Improper connection of the equipment-grounding conductor can
result in a risk of electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the appliance is
properly grounded. Do not modify the plug provided with the
appliance; if it will not fit the outlet have a proper outlet installed by
a qualified electrician.
4
INSTALLATION INSTRUCTION
Step1:
Step2:
PREPARE CUPBOARD OPENING
PREPARE ELECTRICAL WIRING
1
This dishwasher is
shown
as
designed to
fit to the size
CAUTION
below.
For
2
Select
a
location
as
close to sink
as
possible
appliance.
or
Electrical and
and/or other local codes.
than 3 meters from sink for proper
drainage.
4
house fuse
grounding
connections must comply with the national
electrical code/provincial and municipal code
The dishwasher should not be installed
more
remove
open circuit breaker before installation. Do not
use an extension cord or adapter plug with this
for easy connections to water and drain
lines.
3
personal safety,
1
If dishwasher is to be installed in
a
corner,
a
This
appliance must be supplied with
correct rating voltage and hertz as shown
on
minimum 5cm of space is required between
the washer and an adjacent cabinet or a
instruction manual, and connected to
an
individual, properly grounded branch
circuit, protected by minimum 15 amp
wall.
circuit breaker
Wiring
2
or
must be 2
time
delay
wires with
fuse.
ground.
The power plug must be in a accessible
location adjacent to and not behind the
dishwasher and within 1.2 meters of the
dishwasher
3
side.(See
page 7
Fig.A)
The power plug must be correctly earthed,
if in doubt, have it checked by a qualified
Electrician. No other
appliance should be
connected to the same plug outlet by a
double adapter or similar plug.
Unit:mm
If bare
chipboard
is
adjacent
to or above the
dishwasher, it should be sealed with a
waterproofing paint or sealant to prevent
swelling
due to steam.
5
INSTALLATION INSTRUCTION
Step3:
Step4:
PREPARE DISHWASHER FOR
INSTALL THE DISHWASHER IN
INSTALLATION
CUPBOARD
1
Lay
2
Adjust
the
cabinet
as
the dishwasher
legs
on
1
its back.
to the needed
shown in below
height
figure.
of
Before
sliding the dishwasher into the
cupboard opening, all necessary final
height adjustment and balancing
adjustment should be done using the
spanner.
2
Slide the dishwasher into the cabinet
opening carefully.
Make
sure
that the drain
hose inside the cabinet is not kinked
or
stretched.
CAUTION
If the
6
height
of
is below 850mm,
the top table by
cupboard
you should
remove
unscrewing
the 2
screws.
(Two of rear)
INSTALLATION INSTRUCTION
Step5:
DRAIN LINE CONNECTION
1
If the end of drain hose does not fit to the
drain line,
piece of rubber
connector(not supplied) that must be
resistant to heat and detergent and may
obtained from a plumbing shop.
There
2
are
Figure A,
■ When the drain hose is connected
separate stand pipe, it is essential that
use a
2
typical
connections
as
to a
connection is made.
tight
be
an
Refer to
Fig.B
shown in
B.
The "S" trap spigot must be drilled out cleanly
and free of obstruction to its maximum internal
diameter, if used for drainage.
To
prevent siphoning,
one
of the
following
instruction methods must be followed:
■ When the drain hose is connected
to a sink
"s" trap or waste disposal unit, the hose must
be looped up to the underside of the bench
Fig.
top and secured.
B
:
Drainage
pipe.
connection
-
stand
Drain Hose Extension
Extend Drain Hose
Fig.
as
shown below.
A
CAUTION
When you connect or extend Drain Hose,
make sure that drain hose is not kinked.
(Bends should have
7
40
mm
radius.)
INSTALLATION INSTRUCTION
Step6:
Step8:
WATER SUPPLY CONNECTION
HOW TO LEVEL THE PRODUCT
1
Connect the water
supply hose
to the
behind dishwasher and the water tap
in figure.
After
valve
as
the
if you feel some
frictional sound between the side
product,
sticky or hear a
portion of door and tub when you open or close
the door, you have to adjust the level of product.
shown
This dishwasher may be fed with either hot or
cold water. If the water can not be maintained
Case 1. In
below 65ºC, the dishwasher must be
case
the door is slanted to the
right
connected to cold water.
2
installing
connecting, the sealing tape or sealing
compound should be used to avoid water
When
leaks. Make
sharply
sure
that the line is not kinked
or
bent.
Fig. C
Water tap
?
Water
hose
supply
Valve
?
If the door is slanted to the
right as shown in
figure C, repeat the procedure shown as below
until the door is operated normally.
1) Unscrew(counter-clockwise) the left leg of
back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
When the product is correctly leveled, there do
not remain
Case 2. In
slant, stickiness
case
friction sound.
or a
the door is slanted to the left
Step7:
FINAL CHECK AND
ASSEMBLING
1
Securely hand tighten supply hose to water
supply.
Plug power supply cord into an earthed the
power plug and switch on.
Fig.
?
2
the dishwasher
Operate
(Quick cycle
water leak
D
If the door is slanted to the left
through
cycle
is recommended) to check for
and operating conditions.
?
not remain
8
shown in
the
procedure shown as below
until the door is operated normally.
1) Unscrew(counter-clockwise) the right leg of
back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
When the product is correctly leveled, there do
figure D, repeat
one
as
slant, stickiness
or a
friction sound.
PARTS NAME
1.
Vapor vent
11.
Adjust Leg
2. Control Panel
12.
Upper
3. Door Handle
13.
Cutlery
4. Front Cover
14.
Detergent
5. Lower Cover
15.
Vapor
6. Process Monitor
16.
Upper Spray
7. Power Switch
17. Lower
8. Drain Hose
18. Filter ASM
9. Inlet valve ASM
19. Lower Rack
10. Power Cord
Inlet Hose
9
Rack
Rack
& Rinse Aid
Vent Cover
Spray
Arm
Arm
Dispenser
FUNCTION OF CONTROL BUTTON
DELAY START
TIME SAVE
BUTTON
If you want to
?
delay
?
HALF LOAD
This function is for
?
of small load,
In
case
lower rack
the start of selected
saving time and
or
program, press this
button before
energy.
With each press, time
save ON and OFF is
energy.
With each press,
?
pressing start button.
Pressing the delay
time will increase
?
time
?
?
or
by 1 hour.
The delay start time
can be adjusted from
BUTTON
use
upper
can
select upper
works vario
time will be shorten.
operate upper and lower spray
case
arm
washing,
which
alternately.
CHILD LOCK
machine, the power may
PROGRAM
remaining
the control buttons to
When power is
on, program is
time
prevent all the setting
automatically
Self
from
to normal.
and
?
diagnosis
error
message
display
disturbances to the
automatically turned
off for safety.
TIME
?
?
automatically
switches off for safety
and energy saving.
If case of irregular surge
be
REMAINING
Indication of
After operating, this
button
1 hour to 19 hours.
?
?
lower rack only.
function, the operating
In
For operating, press this
button first for power
on.
When select this
?
?
only to save
you don't select this
button, the machine always
repeated.
?
POWER SWITCH
Used
a
?
to lock or unlock
being changed by
child.
For
locking/unlocking,
press Delay Start and
?
set
?Ifyouwantto
change the
?
RINSE/
START/PAUSE
SANI
BUTTON
With each
?
press,
rinse+,
repeated during
operation.
rinse+ &
77。C sani
With each press,
Start and Pause is
?
If the machine
rinse,
remains in Pause
77。C sani
mode for 10
T-Save button
program, press the
button and set the
rinse is
minutes, the power
simultaneously.
program you want
repeated.
is
to.
automatically
turned off.
10
HOW TO USE AND OPERATE
1.
Loading your
Be careful
large items not to prevent the
detergent dispenser lid from opening
Dishwasher
For the best
washing performance, it is important that
the dishwasher is loaded according to instructions.
Before loading items into the dishwasher, you must
scrape off large particles in particular non soluble
items such as bones, toothpicks, pips, etc.
loading the dishwasher,
general guidelines:
When
■ Position crockery such that
observe the
3.
following
to use them.
water will contact all
For the
■ Deep based items should be placed
water
run
off and
■ Items with burnt
to
2.
loading
at an
angle
scraps should be soaked
in the dishwasher.
Loading
to
Take
prior
soup bowls, dishes, pots, pans, lids and
plates,
even
the
grill tray.
Plates should be
positioned upright
and
facing
the
center of the rack.
Pots, pans and large dishes
must be turned
upside
down.
Take
care
spray
care
sharp
the Lower Rack
The lower basket is best loaded with dinner
knives, place
at
seperate rack for knives
located at upper rack.
dry properly.
on
Cutlery
Basket
Cutlery should be mixed within each section of
the cutlery basket to prevent nesting of similar
items. Place the cutlery in the cover with the
handles down. The cover can be hinged and
clipped away from the basket if you choose not
surfaces.
help
Using
the
not to obstruct the rotation of the
arms.
11
when
items.
loading
and
unloading
HOW TO USE AND OPERATE
4.
Loading
the
Upper
Rack
5.
The upper rack is best loaded with more
delicate items, small plates, long cutlery, cups,
glasses and dishwasher safe plastic items. Plates
Adjusting
the
Upper
Rack
Your upper rack can be raised or lowered to
cater for different size of crockery. Before
adjusting, ensure rack is empty of
all crockery and side the rack out.
Reinsert the rack in the chosen position.
Fitting the rack back into the standard position
should be
positioned upwards with the plate
bottom facing the front of the rack.
Cups, glasses and bowls must be positioned
upside down.
Extra cups or cooking utensils can be laid on
reduces the space between the upper and lower
rack.
the fold down cup racks which may also
provide support for long stem glasses.
Take
spray
not to obstruct the rotation of the
care
After adjusting, check that the spray
is free to rotate.
under the upper rack.
arm
arm
?
Front
Non Dishwasher Safe Items
The combination of high water temperatures and
dishwasher detergent may damage particular items,
therefore
we
do not recommend
dishwasher to wash the
using the
following:
Copper or anodized aluminum
Hand painted silver or gold leaf crockery
Wood
Iron
or
bone handled utensils
or non
rust
WARNING
proof utensils
Plastic items which
are
not
Before adjusting, ensure rack is empty
of all crockery.
Otherwise crockery may be damaged
dishwasher safe.
or
12
you may be
injured.
HOW TO USE AND OPERATE
6.
?
Adding Detergent
Dispenser
must be
Detergent
chamber before
put into the detergent
starting
every program except
the Pre-Wash.
the
detergent intended for household
dishwashers. (Ordinary hand-washing
detergent should not be used, because the
foam can interfere with proper operation.)
?
Use
?
Chambers hold
?
Push latch to open
only
15g
and
The amount of
program.
detergent depends on
Refer to the guide table.
AMOUNT OF DETERGENT
Intensive
25g
Normal
20g
Eco
15g
Gentle
10g
Quick
10g
After the
detergent
No
is
Place proper
detergent into this
the
PROGRAM
Pre-Wash
?
25g.
compartment
Detergent
detergent
supplied,
detergent intended for household
dishwashers. (Ordinary hand-washing
detergent should not be used, because the
foam can interfere with proper operation.)
Use
the chamber lid
should be closed.
?
?
Information
only
the
The
detergent is dispensed automatically
during the operation.
The chamber lid remains open after
WARNING
The
detergent
detergent and
operation.
used is
a
special
Dishwasher
like all household chemicals
should be treated
poison and kept out
of reach of children. At completion of each
wash program, the detergent compartment
should be checked and any remaining
detergent removed.
13
as a
HOW TO USE AND OPERATE
Adding Rinse
Dispenser
7.
To fill the Rinse Aid
Aid
chamber,
rotate the round
cap counter clockwise and remove. Fill the
container to the maximum level with a good
quality
Rinse Aid, then
replace
and lock the
cap.
The Rinse Aid is
during
the
Depending
automatically dispensed
final rinse cycle.
on
the
dosage setting
and the
number of washes, the chamber may need only
to be topped up once per month. The rinse aid
level
can
be checked
by looking
at the indicator
window when the dishwasher door is
fully
open.
Black indicates sufficient Rinse Aid
O Clear indicates Rinse Aid
The
dosage setting
installations.
is
required
factory set to
If, after washing, you
suit most
notice
cloudy spots, streaks or water marks on your
glassware, it may be necessary increase the
setting. To do so, remove the cap and rotate the
indicator arrow to a higher setting then replace
the cap If the glasses are smeared or there is
foam present on the bottom of the glass or the
bottom of the machine. Select a lower setting.
.
Rinse Aid Information
Rinse Aid is necessary in order to get spot and
streak free dishes as well as improved drying.
Using the correct amount will improve wash
performance. However, using too much can
produce excess foam leading to possible water
leaks.
14
HOW TO USE AND OPERATE
8. Fold down dividers.
■ Fold-down dividers
lowered to
at the
lower rack
improve stacking
10.
can
be
of pots and
■ Appliance loaded in accordance with
pans.
standard
?
?
?
?
?
?
9.
Drying
■ At the end of the program, it is
recommended to
assist in
Energy Test
(AS / NZS 2007)
fully
open the door to
drying.
15
specifications.
Example of loaded dishwasher : p.11~12
Capacity : 14 place settings
Comparability course : Economy with
Rinse+ (R+1) option.
Rinse aid setting : 3
Reference cleaner : 6g of detergent onto the
inside surface of the door and fill 24g into the
detergent dispenser.
Height-adjustable Rack-U must be inserted
in the uppermost position.
WASH OPTIONS
Before
the wash program, press the power button. Then Normal program
will be selected with remaining time on display window. To change the program,
selecting
press the program button
required.
Start / Pause Button
After
or
Child Lock
wash program, press the Start
Pause button to start the wash cycle.
selecting
To reduce the
a
interrupting
If at any time you want to interrupt the washing
cycle, press the Start or Pause button. Your
dishwasher will then pause. Press the Start
Pause button again to re-start dishwasher.
For
or
locking
can
be selected.
unlocking, press "Delay
buttons simultaneously.
or
and "T-Save"
Start"
Sani-Rinse
Once you select a program, the progress
indicators light(Wash, Rinse, Dry). When press
the Start or Pause button to start the program,
light
of children
the dishwasher when unattended,
the child lock feature
Progress Indicators
the current stage
possibility
When you want to rinse dishes with higher
temperature for sanitation, use this function at
any program. If you choose this function, the
water temperature goes up to 77˚C when
will blink.
rinsing.
Press Rinse button until
Delay Start
This function enables the wash
anywhere
cycle
Set the
Half Load
With each press, upper rack
on), lower rack only(Lower
by using
by pressing the
"Delay Start" button. The delay start time is
increased by 1 hour for each pressing.
delay
time you want
In
automatically after the delayed
shown in the display has expired.
Rinse Plus
when you select any program, the
Rinse process is done only two ( 1 normal rinse
Normally
heating rinse) or three (2 normal rinse +
heating rinse) times according to selected
program. But if you want to rinse more, you
use this function. As you select R+1 with
pressing
done
1
can
Rinse button, the normal rinse will be
one
time
case
of small load
lower rack
be started
+1
only(Upper light
light on) can be
selected.
Press the start button. Then the program will
time
on.
to start
between 1 to 19 hours later.
Select the program that you want
the program button.
"R77˚" is lighted
more.
16
only
washing,
use
to save energy.
upper
or
PROGRAMS
Intensive Wash
This program is for
including pots,
heavily
Eco Wash with
soiled loads
Rinse+
pans and casserole dishes.
option
This program is for
loads.
normally
soiled
everyday
Normal Wash
This program is for
loads.
normally
soiled
everyday
Gentle Wash
This program is for
light
delicate items like
glasses.
Eco Wash
This program is for
washing
soiled
everyday
loads.
Quick Wash
This program is for that quick wash of lightly
soiled recently used dishes and cutlery.
17
CHECK AND CARE
To prevent trouble and poor operating, it is important to check and
filters and spray arms at intervals.
Filters
Upper Spray
?
Remove the lower rack first.
?
?
Turn the mesh filter counterclockwise off.
?
?
Take out the mesh filter, upper STS filter and
out filter.
?
?
Lower
?
Spray
Check that the water jet holes
by
?
Arm
food
are
not blocked
particles.
When necessary to clean,
remove
the
arm
by
pulling up.
?
Clean the spray
down.
arm
and
replace by pushing
18
food
for the
Arm
Pull the upper rack forwards.
Check that the water jet holes
by
Clean them if necessary.
Replace them in the reverse order.
care
are
not blocked
particles.
?
When necessary to clean,
unscrewing the nut.
?
Clean the spray
reverse order.
arm
and
remove
replace
the
arm
it in the
by
TROUBLE SHOOTING GUIDE
If
a
problem
occurs
in your machine, call for service.
Before you call for service, check the below instructions to
problem can be solved by yourself first.
on
do not
lamps
come
when the power switch
on.
The machine does not start.
Water is not
pumped
show
"
shows
"
(The display
The
display
(Automatically
The
The
The
display
display
The spray
Drain
away.
"
"
code)
code
Pump operated)
?
Fuse blown
?
The
?
Door is not
?
The start button is not
?
The drain hose is kinked.
?
The filter is
?
Excessive water is
?
The inlet valve is troubled.
fully
cut
was
off.
closed.
pressed.
clogged. (Clean
the
filter)
supplied than
normal water level.
?
Water is not
shows
"
"
code
?
Water
?
Water is leaked
?
The circuit of Heater is troubled.
?
The
mounting of spray arms is blocked by food
particles. (Clean the holes of the spray arm)
?
The amount of
?
Too little Rinse-aid
dispensed.
?
Too little Rinse-aid
dispensed.
?
Incorrect amount of
"
"
code
does not rotate
are
on
are
not
results
left
on
the
supplied. (Water tap
leakage
is not
opened)
in Hose connections
by damages.
detergent
or
rinse-aid set
incorrectly.
washing.
left
Washing
satisfactory.
of the house
electricity
tripped.
code
dish washer after
Dry
circuit breaker
shows
deposits
results
or
"
arms
are
properly
inserted in the socket.
Plug
smoothly
Streaks
is not
?
"
shows
display
White
whether the
Possible Causes
Problem
The
see
glassware
satisfactory.
are
not
?
?
?
?
?
detergent.
Utensils incorrectly arranged or overloaded.
Filters are clogged.
Water jet holes of spray arms blocked.
Spray arms' rotation obstructed by utensils.
Unsuitable program selected.
19
Capacity
14 Place
Dimension
600x600x850mm(WxDxH)
Weight
52
Power
Supply
See
rating
label
Power
Consumption
See
rating
label
Water
Consumption
See energy label
Water Feed Pressure
P/No.: 3828DD7001W
settings
kg
50~800kPa
Download PDF