LG | LD-14AW1 | LG LD-14AW1 Owner’s Manual

600mm
600mm
850mm
Capacity
14 Place
Dimension
600x600x850mm(WxDxH)
Weight
52
Power
Supply
See
rating
label
Power
Consumption
See
rating
label
Water
Consumption
See energy label
Water Feed Pressure
P/No.: 3828ED7001H
settings
kg
30~800kPa
DISHWASHER
OWNER'S MANUAL
MODEL
:
LD-14AW1, LD-14AT1
Please read this manual
carefully
before
operating your
dishwasher. Retain it for future reference.
CONTENTS
SAFETY AND CAUTION
3
INSTALLATION INSTRUCTION
4
PARTS NAME
8
FUNCTION OF CONTROL BUTTON
9
HOW TO USE AND OPERATE
10
WASH OPTIONS
15
PROGRAMS
16
CHECK AND CARE
17
TROUBLE SHOOTING GUIDE
18
SPECIFICATIONS
SAFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING
?
Please read this manual
using
?
?
-
using your dishwasher, follow
including the following:
When
carefully before
?
the dishwasher for the first time.
This manual contains very important notes
regarding the installation, use and
maintenance of your dishwasher.
The manufacturer can not be responsible
?
for
?
problems caused by ignoring these
safety and caution instructions.
This dishwasher is designed for normal
household
?
?
Do not
?
the dishwasher for industrial
safety
is
rating label.
only guaranteed
cable
?
or
?
not
use an
?
extension
cord.)
?
Only suitable household utensils should
placed in the dishwasher. (Please avoid
temperature
65˚C,
?
?
?
Keep detergents away from children.
If the hot water exceeds 65˚C, adjust the
water heater
setting.
can
?
If the hot water
not be maintained
disturbance
on
its
This
appliance must be positioned so that
plug is accessible.
Controls may be locked using "child lock"
mode to prevent from starting dishwasher
accidentally.
The appliance is not intended for use by
or
infirm persons without
supervision.
Young children should be supervised to
ensure that they do not play with the
appliance.
Do not insert anything such as coin into
the dishwasher must be connected
parts and noise.
to cold water.
?
use any kinds of solvent in your
dishwasher. They may cause an explosion
or fire.
Do not expose skin to vapor vent.
During operation, as hot steam may scald.
?
Dishwasher
Do not
Do not spray water on the appliance. It
may cause the failure of electric parts or
Do not allow children to
Do not
push
down
or
sit
away from the dishwasher when the door
is open.
Check that the detergent receptacle is
operate the
on
detergents are strongly
They can be extremely
dangerous if swallowed. Avoid contact
with skin and eyes and keep children
alkaline.
dishwasher.
?
the
the vapor vent.
It may cause the failure of mechanical
below
electric shock.
?
automatically stops
young children
utensils; that are non-heartresistant, metal
decorated, etc.)
?
person in order to avoid a hazard.
This appliance is fitted with a safety
the
when
be
?
washing.
The detergent for dishwasher should be
used for normal operation.
If power supply cord is damaged, it must
only be replaced by the manufacturer or
its service agent or a similar qualified
mains.
the earth system of your house is in
accordance with the related local
regulations. (Do
detergent for hand
operation
exposed to heavy
and commercial use, or other purpose.
Electrical connection must be in
Electrical
the
precautions,
of the dishwasher when it is
accordance with the
?
use
function that
use.
use
Do not
basic
the inner door
empty after completion of the wash cycle.
when the door
opened. It may cause the
deformation or failure of your dishwasher.
?
The
appliance is to be connected
using new hose-sets
water mains
to the
and that
old hose-sets should not be reused.
3
INSTALLATION INSTRUCTION
Step1:
Step2:
PREPARE CUPBOARD OPENING
PREPARE ELECTRICAL WIRING
1
This dishwasher is
size shown
as
designed to
fit to the
CAUTION
below.
For
2
Select
a
location
as
close to sink
as
this
house fuse
or
appliance.
Electrical and
grounding
comply with the national
code/provincial and municipal code
connections must
electrical
The dishwasher should not be installed
more
remove
open circuit breaker before installation. Do not
use an extension cord or adapter plug with
possible for easy connections to water and
drain lines.
3
personal safety,
and/or other local codes.
than 3 meters from sink for proper
drainage.
1
4
If dishwasher is to be installed in
a
corner,
minimum 5cm of space is required
between the washer and an adjacent
on
instruction manual, and connected to
individual, properly grounded branch
circuit, protected by minimum 15 amp
an
wall.
or a
appliance must be supplied with
rating voltage and hertz as shown
correct
a
cabinet
This
circuit breaker
Wiring
2
600
820-870
3
75
600-605
Cut out for
hoses and electrical
cables on either side.
(appox.
is
adjacent
100
x
75)
to or above the
due to steam.
CAUTION
If the
height
should
the 4
of
is below 850mm, you
the top table by unscrewing
(Two of front and two of rear)
cupboard
remove
screws.
ground.
4
side.(See
page 6
Fig.A)
Electrician. No other
appliance
plug
should be connected to the
same
outlet
or
plug.
dishwasher, it should be sealed with a
waterproofing paint or sealant to prevent
swelling
fuse.
The power plug must be correctly
earthed, if in doubt, have it checked by a
qualified
chipboard
delay
wires with
The power plug must be in a accessible
location adjacent to and not behind the
dishwasher
100
If bare
time
dishwasher and within 1.2 meters of the
Min.
Unit:mm
or
must be 2
by
a
double
adapter
similar
INSTALLATION INSTRUCTION
Step3:
Step5:
PREPARE DISHWASHER FOR
INSTALL THE DISHWASHER IN
INSTALLATION
CUPBOARD
the dishwasher
1
Lay
2
Adjust
the
cabinet
as
legs
on
its back.
to the needed
shown in
figure
Before
sliding the dishwasher into the
cupboard opening, all necessary final
height adjustment and balancing
adjustment should be done using the
1
height
of
#1.
spanner.
Slide the dishwasher into the cabinet
2
opening carefully.
Make
sure
that the
drain hose inside the cabinet is not
Adjust
kinked
screw
or
stretched.
CAUTION
figure
#1
If the
height
should
the 4
of
is below 850mm, you
the top table by unscrewing
(Two of front and two of rear)
cupboard
remove
screws.
Step4:
CONNECT DRAIN HOSE TO
600mm
DISHWASHER
1
Turn the drain connector at the back of
dishwasher to drain direction
2
Top
Connect the drain hose to the drain
connector
tightly using
hose
clamp.
Water
Hose
Clamp
820~7m600~605mm
supply
Drain Hose
5
table
INSTALLATION INSTRUCTION
Step6:
DRAIN LINE CONNECTION
1
If the end of drain hose does not fit to
When the drain hose is connected to
the drain line,
separate stand pipe, it is essential that
air tight connection is made.
of rubber
piece
connector(not supplied) that must be
resistant to heat and detergent and may
be obtained from a plumbing shop.
2
There
are
shown in
use a
2
typical connections
Figure A, B.
Refer to
a
an
Fig.B
as
Air Tight
Connection
70mMin./1ax 30mMin.
The "S" trap spigot must be drilled out
cleanly and free of obstruction to its
maximum internal diameter, if used for
drainage.
To prevent siphoning, one of the following
instruction methods must be followed:
40
Standpipe
When the drain hose is connected to
sink "s" trap or waste disposal unit, the
hose must be looped up to the underside
Fig.
of the bench top and secured.
B
:
Drainage
connection
-
stand
pipe.
Drain Hose Extension
Extend Drain Hose
70mMin. 10 mMax.
mm
diametre min.
a
Sink
200
mm
as
shown below.
Max.
Drain Hose
Inlet Hose
Copper pipe
Ø20mm flared
30mMin.
Fig.
Power
Cord
30mMin.
A
at drain hose
and other end
if required
70mMin./1ax
Drain hose extension or 16-20mm inside Ørubber
hose able to withstand 90˚C hot water
CAUTION
When you connect or extend Drain Hose,
make sure that drain hose is not kinked.
(Bends should have
6
40
mm
radius.)
INSTALLATION INSTRUCTION
Step7:
Step9:
WATER SUPPLY CONNECTION
HOW TO LEVEL THE PRODUCT
1
Connect the water
supply pipe
water valve behind dishwasher
shown in
2
to the
After
installing
hear
sticky
side portion
or
as
figure.
a
the
product, if you feel some
frictional sound between the
of door and tub when you open or
adjust the level of
close the door, you have to
product.
connecting, the sealing tape or
sealing compound should be used to
When
Case 1. In
case
the door is slanted to the
right
avoid water leaks.
Make
or
sharply
Slant to
the right
that the line is not kinked
sure
bent.
Shut off Valve
DOOR
To Dishwasher
Fig. C
?
If the door is slanted to the
right
as
shown in
figure C, repeat the procedure shown as
below until the door is operated normally.
1) Unscrew(counter-clockwise)
back side and
of
the
do not remain slant, stickiness
sound.
Case 2. In
Step8:
leg
high
opening of door if there still
remains sticky or friction sound.
When the product is correctly leveled, there
2) Check
?
the left
the level.
case
or a
friction
the door is slanted to the left
FINAL CHECK AND
Slant to
ASSEMBLING
1
the left
DOOR
Securely hand tighten supply hose to
water supply.
Plug power supply cord into an
earthed the power plug and switch on.
Fig.
?
2
Operate the dishwasher through one
cycle (Quick cycle is recommended)
to check for water leak and operating
D
If the door is slanted to the left
conditions.
?
7
as
shown in
the
procedure shown as
below until the door is operated normally.
1) Unscrew(counter-clockwise) the right leg
of back side and high the level.
2) Check the opening of door if there still
remains sticky or friction sound.
When the product is correctly leveled, there
figure D, repeat
do not remain slant, stickiness
sound.
or a
friction
PARTS NAME
6
1
12
7
16
8
2
13
17
3
9
14
4
18
10
5
15
19
11
11.
Adjust Leg
2. Control Panel
1.
12.
Upper
3. Door Handle
13.
Cutlery
4. Front Cover
14.
Detergent
5. Lower Cover
15.
Vapor Vent
6. Process Monitor
16.
Upper Spray
7. Power Switch
17. Lower
8. Inlet valve ASM
18. Filter ASM
9. Drain Hose Connector
19. Lower Rack
Vapor
vent
Rack
Rack
& Rinse Aid
Cover
Spray
Arm
Arm
10. Power Cord
Accessories
Inlet Hose
8
Drain Hose
Dispenser
FUNCTION OF CONTROL BUTTON
DELAY START
TIME SAVE
BUTTON
?
If you want to delay
the start of selected
?
?
?
pressing start button.
Pressing the delay
?
energy.
When select this
function at Intensive
plus, Intensive,
time will increase
Normal and Eco
time
course,
by
1 hour.
?
This function is for
saving time and
program, press this
button before
?
washing
delay start time
can be adjusted from
lowered
1 hour to 19 hours.
time be shorten.
by
?
5 C than
normal condition and
BUTTON
With each press, upper rack
only(Upper light on), lower rack
only(Lower light on) and vario
washing(Upper and Lower lights
on together) can be selected.
In case of small load washing,
use upper or lower rack only to
save
temperature will be
The
POWER SWITCH
HALF & VARIO
In
energy.
operating, press this
button first for power
?
For
?
After operating, this
on.
button
automatically
safety
and energy saving.
If case of irregular surge
switches off for
?
you want powerful
washing, use vario washing
disturbances to the
option with main program.
be
case
machine, the power may
automatically turned
safety.
off for
Power
Delay
Start
Rinse
Child Lock
REMAINING
TIME
?
?
Indication of
Used to lock
?
?
or
remaining
unlock the control
time
buttons to prevent all
the setting from being
Self
diagnosis
error
message
display
PROGRAM
CHILD LOCK
and
?
changed by a child.
For locking/unlocking,
press Delay Start and
T-Save button
simultaneously.
When power is
on, program is
automatically
set
to normal.
?Ifyouwantto
change the
program, press the
button and set the
program you want
to.
?
RINSE/
START/PAUSE
SANI
BUTTON
With each
press,
rinse+,
repeated during
operation.
rinse+ &
77 C sani
With each press,
Start and Pause is
?
?
If the machine
rinse,
remains in Pause
77 C sani
mode for 10
rinse is
minutes, the power
repeated.
is
automatically
turned off.
9
HOW TO USE AND OPERATE
1.
Loading your
For the best
Be careful
large items not to prevent
detergent dispenser lid from
opening
Dishwasher
the
washing performance, it is important
according to
that the dishwasher is loaded
instructions.
3.
Before
loading items into the dishwasher, you
must scrape off large particles in particular non
soluble items such as bones, toothpicks, pips, etc.
Using
Cutlery
the dishwasher, observe the
loading
following general guidelines:
cutlery
Basket
basket to prevent
of similar items. Place the
nesting
the
Cutlery
should be mixed within each
section of the
When
the
cover
cutlery
with the handles down. The
in
cover
be hinged and clipped away from the
basket if you choose not to use them.
For the knives, place at seperate rack for
can
Position
crockery such that water will contact
all surfaces.
Deep based items should be placed at an angle
to help water run off and dry properly.
knives located at upper rack.
Items with burnt
Take
on
scraps should be soaked
sharp
prior to loading in the dishwasher.
2.
Loading
care
when
loading
and
2
1
unloading
items.
the Lower Rack
The lower basket is best loaded with dinner
soup bowls, dishes, pots, pans, lids
and even the grill tray.
plates,
Plates should be
facing
positioned upright
Pots, pans and large dishes
upside
Take
and
the center of the rack.
must be turned
down.
care
not to obstruct the rotation
of the spray
5
3
arms.
3
Dessert
2
1
2
1
2
1
2
1
4
4
2
1
4
4
1
2
4
4
1
2
1
2
1
2
1
2
1
2
1
2
3
plate
3
1
3
Soup plate
4
2
3
3
4
4
4
4
4
Dessert
plate
4
3
3
1
2
345
3
4
Dinner
Soup plate
plate
10
3
3
3
5
3
HOW TO USE AND OPERATE
4.
Loading
the
Upper Rack
5.
Adjusting
the
Upper
Rack
The upper rack is best loaded with more
delicate items, small plates, long cutlery,
Your upper rack can be raised or lowered to
cater for different size of crockery. Before
cups, glasses and dishwasher safe plastic
items. Plates should be positioned upwards
adjusting, ensure rack is empty of
all crockery.
You can change the position of the upper
rack by pulling the rack upward(to upper
position) or pushing the button to take the
rack down. (to lower position)
with the
plate
bottom
facing
the front of the
rack.
Cups, glasses
upside down.
and bowls must be
positioned
Extra cups or cooking utensils can be laid
on the fold down cup racks which may also
provide support for long stem glasses.
It is recommended to level the upper rack
gently for more convenience and correct
Take
And when you pull the rack upward, hold
the middle location of the upper rack
spray
care
arm
operation.
not to obstruct the rotation of the
under the upper rack.
(
marked
After
position)
adjusting,
check that the spray
arm
is free to rotate.
Front
Non Dishwasher Safe Items
button
The combination of high water temperatures and
dishwasher detergent may damage particular
items, therefore
we
do not recommend
dishwasher to wash the
using
the
following:
Copper or anodized aluminum
Hand painted silver or gold leaf crockery
Wood
Iron
or
bone handled utensils
or non
rust
proof utensils
Plastic items which
are
not
dishwasher safe.
11
HOW TO USE AND OPERATE
6.
?
Adding Detergent
Dispenser
Detergent
must be
chamber before
put into the detergent
starting
every program
Push latch to open
except the Pre-Wash.
?
Use
only
the
detergent
intended for
household dishwashers.
washing detergent
because the foam
(Ordinary hand-
should not be used,
can
interfere with proper
operation.)
?
Chambers hold
?
The amount of
15g
and
Place proper
detergent into this
25g.
detergent depends on
guide table.
the
compartment
program. Refer to the
PROGRAM
AMOUNT OF DETERGENT
Intensive+
25g
Intensive
25g
Normal
20g
Eco
15g
Quick
10g
Pre-Wash
?
After the
detergent
No
is
Detergent
Use
detergent
supplied,
?
The chamber lid remains open after
detergent
washing detergent
because the foam
chamber lid should be closed.
The
the
intended for
household dishwashers.
the
?
only
Information
(Ordinary hand-
should not be used,
can
interfere with proper
operation.)
detergent is dispensed automatically
during the operation.
WARNING
The
detergent
detergent and
operation.
used is
a
special
Dishwasher
like all household chemicals
should be treated
poison and kept out
of reach of children. At completion of each
wash program, the detergent compartment
should be checked and any remaining
detergent removed.
12
as a
HOW TO USE AND OPERATE
7.
Adding Rinse
Dispenser
To fill the Rinse Aid
Aid
chamber,
rotate the
round cap counter clockwise and remove.
Fill the container to the maximum level
with
a
during
Rinse Aid, then
good quality
and lock the cap.
The Rinse Aid is
replace
automatically dispensed
cycle.
the final rinse
Depending
on
the
dosage setting
and the
number of washes, the chamber may need
only to be topped up once per month. The
rinse aid level
can
be checked
by looking
at
the indicator window when the dishwasher
door is
fully
open.
Black indicates sufficient Rinse Aid
O Clear indicates Rinse Aid
The
dosage setting
most installations.
required
is
factory set to suit
If, after washing, you
Rinse-Aid
Indicator
Adjust Lever
(Rinse)
notice
on
cloudy spots, streaks or water marks
your glassware, it may be necessary
increase the
setting.
To do so,
remove
the
cap and rotate the indicator arrow to a
higher setting then replace the cap If the
.
smeared
Rinse Aid Information
there is foam present
glasses
on the bottom of the glass or the bottom of
are
the machine. Select
or
a
lower
setting.
Rinse Aid is necessary in order to get spot
and streak free dishes as well as improved
drying. Using the correct amount will
improve wash performance. However, using
too much can produce excess foam leading
to possible water leaks.
13
HOW TO USE AND OPERATE
8. Fold down dividers.
Fold-down dividers at the back of the rack
be lowered to
improve stacking
10.
can
of pots and
pans.
?
?
?
?
?
?
9.
Energy Test
(AS / NZS 2007)
Drying
At the end of the program, it is recommended
to fully open the door to assist in drying.
14
Appliance loaded in accordance with
standard specifications.
Example of loaded dishwasher : p.10~11
Capacity : 14 place settings
Comparability course : ECO with Vario
option.
Rinse aid setting : 3
Reference cleaner : 6g of detergent onto
the inside surface of the door and fill 24g
into the detergent dispenser.
Height-adjustable Rack-U must be
inserted in the uppermost position.
WASH OPTIONS
Before
the wash program, press the power button. Then Normal
program will be selected with remaining time on display window. To change the
program, press the program button required.
selecting
Start / Pause Button
After
or
Child Lock
selecting wash program, press the Start
Pause button to start the wash cycle.
To reduce the
a
possibility
of children
starting
the dishwasher when unattended, the child
If at any time you want to interrupt the
washing cycle, press the Start or Pause button.
lock feature
can
be selected.
Your dishwasher will then pause. Press the
Start or Pause button again to re-start
For
dishwasher.
simultaneously.
locking or unlocking, press
Start" and "T-Save" buttons
Progress Indicators
"Delay
Sani-Rinse
Once you select a program, the progress
indicators light(Wash, Rinse, Dry). When press
the Start or Pause button to start the program,
When you want to rinse dishes with higher
temperature for sanitation, use this function
the current stage
the water temperature goes up to 77˚C when
light
at any program. If you choose this
will blink.
function,
rinsing.
Press Rinse button until "R77˚" is
Delay Start
This function enables the wash
anywhere
cycle
to start
Half & Vario
between 1 to 19 hours later.
Select the program that you want
With each press, upper rack only(Upper
light on), lower rack only(Lower light on)
by using
the program button.
Set the delay time you want
by pressing the
"Delay Start" button. The delay start time is
increased by 1 hour for each pressing.
and vario
washing(Upper and Lower lights
together) can be selected.
In case of small load washing, use upper or
lower rack only to save energy.
In case you want powerful washing, use
Vario washing option with main program.
on
Press the start button. Then the program will
be started
automatically after the delayed
display has expired.
time shown in the
Rinse Plus
when you select any program, the
Rinse process is done only two ( 1 normal
Normally
rinse +1
+
1
heating rinse) or three (2 normal rinse
heating rinse) times according to selected
program. But if you want to rinse more, you
can use this function. As you select R+1 with
pressing
done
Rinse button, the normal rinse will be
one
time
lighted on.
more.
15
PROGRAMS
Model
:
LD-14W1, LD-14AT1
Program
WASHMain
Pre Wash
wash
RINSE
Rinse 1
Rinse 2
Rinse 3
Heating
DRY
Rinse
50C
70C
70C
40C
70C
70C
60C
65C
40C
50C
40C
40C
Intensive+
Intensive
Normal
Eco
Quick
Pre-Wash
Intensive Wash
This program is for
including pots,
heavily
Intensive+ Wash
soiled loads
This program is for very heavily soiled
loads including pots, pans and casserole
pans and casserole dishes.
dishes which may have
dry
food residue.
Normal Wash
This program is for
everyday loads.
normally
Quick Wash
soiled
This program is for that quick wash of
lightly soiled recently used dishes and
Eco Wash
This program is for
loads.
cutlery.
light
soiled
everyday
16
CHECK AND CARE
To prevent trouble and poor operating, it is
arms at intervals.
important
to check and care for the
filters and spray
Upper Spray Arm
Filters
?
Remove the lower rack first.
?
?
Turn the mesh filter counterclockwise off.
?
?
Take out the mesh filter and upper STS
filter.
?
?
Pull the upper rack forwards.
Check that the water jet holes
blocked
Clean them if necessary.
Replace them in the reverse order.
by
food
When necessary to clean,
by unscrewing the nut.
?
Clean the spray
reverse order.
upper STS filter
Upper spray arm
Lower
Spray Arm
?
Check that the water jet holes
?
When necessary to clean,
blocked
by
food
are
not
remove
the
particles.
arm
by pulling up.
?
Clean the spray
down.
arm
and
replace by pushing
17
not
remove
the
particles.
?
mesh filter
are
arm
and
replace
arm
it in the
TROUBLE SHOOTING GUIDE
If
a
problem
occurs
in your machine, call for service.
Before you call for service, check the below instructions to
problem can be solved by yourself first.
on
whether the
Possible Causes
Problem
The
see
do not
lamps
Fuse blown
?
The
?
Door is not
?
The start button is not
?
The drain hose is kinked.
code)
?
The filter is
on.
The machine does not start.
pumped
away.
properly
or
circuit breaker
of the house
electricity
fully
tripped.
was
cut
off.
closed.
pressed.
(The display show
"
The
display
shows
"
"
code
?The machine is inclined.
The
display
shows
"
"
code
?
Water is not
The
display
shows
"
"
code
?
Water
?
Water is leaked
?
The circuit of Heater is troubled.
?
The
mounting of spray arms is blocked by food
particles. (Clean the holes of the spray arm)
?
The amount of
?
Too little Rinse-aid
dispensed.
?
Too little Rinse-aid
dispensed.
?
Incorrect amount of
The
display
The spray
shows
"
inserted in the socket.
Plug
?
when the power switch
Water is not
is not
?
come
"
"
code
does not rotate
arms
smoothly
White
deposits
are
dish washer after
Streaks
are
Dry results
on
the
the
filter)
supplied. (Water tap
leakage
is not
opened)
in Hose connections
by damages.
detergent
or
rinse-aid set
incorrectly.
washing.
left
on
are
not
Washing results
satisfactory.
left
clogged. (Clean
glassware
satisfactory.
are
not
?
?
?
?
?
detergent.
incorrectly arranged or overloaded.
Filters are clogged.
Water jet holes of spray arms blocked.
Spray arms' rotation obstructed by utensils.
Utensils
Unsuitable program selected.
18
Memo
19
Download PDF