LG | VR63409LV | LG VR63409LV Owner’s Manual

OWNER’S MANUAL
ROBOKING
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading this manual,
please keep it in an easily accessible location.
VR634** Ser
VR644** Ser
VR635** Ser
www.lg.com
FEATURES
Corner Master
By having adopted a brand new concept design that is appropriate for walls,
the Robot Cleaner's cleaning performance is incredibly efficient.
Learning Mode
The Robot Cleaner is capable of memorizing the cleaning environment
via its Smart Operation feature for smarter cleaning.
Turbo Mode
In the Turbo mode, the Robot Cleaner operates the suction motor and the
brushes at a greater speed giving cleaner results.
Drawer Mop Plate (Selected models only (VR627*Ser.))
The "Drawer mop plate" makes it much easier for users to fit and remove the
mop without having to turn over the device.
My Space Mode
By commanding it to clean a particular area, the Robot Cleaner quickly cleans
that desired area.
Repeat Cleaning
The Robot Cleaner will continuously clean until the battery runs out.
Location Search Function
If the Robot Cleaner is moved from a spot while operating, the device will
automatically search for the previous location and return to the spot from
where it was interrupted.
CONTENTS
1
BEFORE USING
2~6
7
8~9
10~11
12
13
14
Safety precautions
Included with product
Parts description
Button functions
Display status information
Before you start
Overview
2
METHOD OF USE
15
16
How to install the home station
How to turn the Robot Cleaner power
supply on & off
17
How to start and stop cleaning
18
How to charge the battery
19~20 Cleaning modes
21
Auxiliary cleaning modes
22
Mop cleaning
(Selected models only (VR627*Ser.))
Location search function
23
24~25 Smart diagnosis
3
HANDLING METHOD AFTER USE
26
27
28
29
30
31
Cleaning the dust bin
Cleaning the dust bin filter
Cleaning the brush
Cleaning the sensors/charging terminals
Cleaning the side brush
Cleaning the ultra microfiber mop
(Selected models only (VR627*Ser.))
4
ADDITIONAL INFORMATION
32~34 Troubleshooting
Before you call for service
35
5
REFERENCE
36
37
Product specifications
Reference items
SAFETY PRECAUTIONS
The purpose of the safety precautions described below is for the user to use the product safely and correctly
to prevent any unexpected risk of injury or damage.
Basic safety precautions
After reading this manual, please keep it in an easily accessible location.
This is the safety alert symbol. This symbol alerts you to potential hazards that can
result in property damage and/or serious bodily harm or death.
Indicates a hazardous situation which, if not avoided, could result in death or serious
WARNING
injury.
Indicates a hazardous situation which, if not avoided, could result in minor or
CAUTION
moderate injury.
WARNING
1. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not
play with the appliance.
3. If the supply cord is damaged, it must be replaced by LG
Electronics Service Agent in order to avoid a hazard
4. This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance must not be made by
children without supervision.
2
SAFETY PRECAUTIONS
WARNING
For your safety, do not remove
the battery from the Robot
Cleaner. If you need to replace
the battery of the Robot Cleaner,
take it to the nearest authorized
LG Electronics service center or
dealer for assistance.
Never use the Robot Cleaner
with a battery and/or home
station from any other product
than the Robot Cleaner.
Doing so can cause fire or product
failure.
Failure to follow this warning can
cause fire or product failure.
Make sure the power cord of
the home station is not crushed
under a heavy object or damaged
by contact with sharp objects.
Failure to follow this warning
can cause electric shock, fire or
product failure. If the power cord
is broken, do not plug it in. Take
the product to an LG Electronics
Authorised service repairer.
Do not place the home station
and the Robot Cleaner near a
heating device.
Doing so can cause product
deformation, fire, or product
failure.
Do not force the power plug to
bend. Do not use the power plug
when it has been damaged or
loosened.
Doing so can cause fire or product
failure.
Do not touch the power plug
with wet hands.
Doing so can cause electric shock.
Do not use the Robot Cleaner
when candles or fragile objects
are placed on the floor.
Doing so can cause fire or product
failure.
Always use a dedicated power
outlet with a 10 amp rating.
If multiple appliances are
connected to an outlet
simultaneously, they can generate
enough heat to cause a fire.
When pulling out the home
station power plug, always pull it
out by grabbing the plug, not the
cord. When pulling out the power
plug, do not to touch the prongs
with your fingers.
Doing so can cause an electric
shock.
Do not allow children or pets to
play with or rest upon the Robot
Cleaner at any time. Do not
use the Robot Cleaner while an
object is hanging from it.
Doing so can cause injury or
product damage.
3
SAFETY PRECAUTIONS
WARNING
Gasoline
Detergent
Do not spray or use inflammable
materials, surfactants, or
drinking water in the vicinity of
the Robot Cleaner.
Doing so can cause fire or product
failure.
* Inflammable materials: gasoline,
thinner, etc.
* Surfactant: detergent, articles
for bath, etc.
Do not insert any part of the
body, such as a hand or foot,
below the brush or wheels of the
Robot Cleaner while in use.
Doing so can cause injury or
product damage.
Do not operate the Robot
Cleaner on narrow and high
furniture such as a wardrobe,
refrigerator, desk, table, etc.
Doing so can cause injury, product
failure or damage which is not
covered by the warranty.
Do not activate the device on a
floor that has more than a 10
degree incline.
The device may not work properly.
4
Turn the power supply off
immediately if any abnormal
sound, odor, or smoke is
generated from the Robot
Cleaner by removing it from the
home station and turning off the
main switch on the rear side of
the unit.
Failure to do so can cause fire or
product failure.
Do not operate the Robot
Cleaner in a room where a child
is sleeping.
Doing so can cause injury or
product damage.
Do not leave Children or
pets near the Robot Cleaner
unsupervised.
Doing so can cause injury or
product damage.
T his product is intended for indoor domestic home
use and should not be used in mobile applications. it
should not be used in commercial applications such
as workshops or garages or around indoor swimming
pools and water features etc.
SAFETY PRECAUTIONS
CAUTION
Frequently empty the dust bin
and maintain its cleanliness.
Do not drop the Robot Cleaner
or subject it to strong impacts.
The dust collected in the dust
bin can trigger allergies and may
contain harmful insects. it should
be cleaned after each use.
Doing so can cause injury or
product failure not covered by the
warranty.
Use the Robot Cleaner indoors
only.
Do not expose the Robot Cleaner
to cold temperatures (less than
5 C) for a long period of time.
Using it outdoors can cause
product failure and irreparable
damage to the unit.
Close the cover of the dust bin
on the main unit before starting
cleaning.
If the cover is not closed, it can
cause injury or product damage.
Doing so can cause product
failure.
Remove any cables or string from
the floor before starting.
Cable or string can get tangled
in the wheels of Robot Cleaner
and cause product failure or
the cord of an appliance can be
disconnected.
DO NOT use the Robot Cleaner
around a banister, staircase or
any other dangerous place.
Make sure the Robot Cleaner is
not put on a table or desk, with
the power ON.
Doing so could cause injury or
damage to the unit.
It may result in an injury or
damage to the product.
In rare cases, the Robot Cleaner’s
brush can damage carpet. If this
happens, immediately stop the
cleaning operation.
Do not allow the Robot Cleaner
to sweep up liquids, blades,
thumb tacks, sharp objects or
ashes, hot or cold, etc.
When a carpet has long tassels,
the tassels can be damaged.
These items can cause product
failure or damage.
Do not let the main unit and
charging terminal of the home
station come into contact with
metallic objects.
Do not put sharp objects into the
opening of the Robot Cleaner’s
ultrasonic sensors.
Doing so can cause product
failure.
Do not put water, detergent, etc.
into or onto the Robot Cleaner.
Doing so can cause product
failure. Do not put any water or
detergent on the Robot Cleaner.
If liquids get inside of the Robot
Cleaner, turn off the power supply
and contact an LG Electronics
sales agent or customer care
center.
Doing so can cause product
failure.
Do not use the Robot Cleaner
when the dust bin is completely
full.
Doing so can cause product
failure.
5
SAFETY PRECAUTIONS
CAUTION
If the floor is wet or has wet
spots, wipe them up before
using the Robot Cleaner. Do not
use the Robot Cleaner on a wet
surface.
Doing so can cause product
failure.
When attaching the mop, ensure
that it is fitted correctly so
that it does not block the lower
camera sensor.
Blocking the bottom camera
sensor may not allow the product
to work correctly.
(Some models may not have the
sensor.)
When the robot cleaner is
operating, it may hit the chair
leg, desk leg, table leg or other
narrow pieces of furniture.
For quicker and better cleaning,
place the dining chairs on top of
the dining table.
NOTE: Very low thresholds will
allow the Robot cleaner to go
over them and perhaps into an
undesirable location. Make sure
that all the doors of the rooms
that are not to be cleaned are
closed.
To save energy when the Robot
Cleaner is not in use for longer
periods, turn off the power
switch, and turn on the power
switch again just prior to using
the Robot cleaner.
Tip
Check the following items before use:
• Empty the dust bin after each operation or prior to it filling up.
• Remove any cables or long strings from the floor.
• Remove any moisture from the floor before cleaning.
• Close the cover of the dust bin before cleaning.
• Remove fragile or unnecessary objects from the room to be cleaned.
For example, remove expensive ceramics and valuables from the floor.
• Confirm whether the battery has sufficient power, and if it is low, recharge it.
• Close the doors of any room that you do not want the Robot Cleaner to enter.
During cleaning, the Robot Cleaner may enter another room and continue cleaning.
• Do not use this product in the room where a child is sleeping alone. The child can be hurt or
woken.
• Remove towels, foot towel or any other thin cloth from the floor as they can get caught by the
brush.
• Before starting the device, it's better to remove carpets that are thicker than 20 mm as they
may cause it to malfunction.
• Please close any balcony doors as the wheels may get stuck while cleaning.
6
INCLUDED WITH PRODUCT
Robot Cleaner
Remote controller
Home station
s Figures can be different from actual objects.
OWNER’S MANUAL
ROBOKING
Quick Guide
Cleaning Robot
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading this manual,
please keep it in an easily accessible location.
This guide briefly describes how to use the Cleaning Robot.
For more detail, please refer to the user manual.
Please read this manual carefully before installing and operating the product.
www.lg.com
www.lg.com
Cleaning Tool
Dust bin filter (spare)
(Selected models only (VR627*Ser.))
Mop plate
(Selected models only (VR627*Ser.))
Quick guide
Operation manual
Ultra microfiber mop (2 pieces)
(Selected models only (VR627*Ser.))
for cleaning sensors
for cleaning the filter
Cleaning brush
(It’s on the dust bin cover)
Batteries for remote controller
(2 units of AAA size)
7
PARTS DESCRIPTION - ROBOT CLEANER
Plan view
Upper camera sensor
Dust bin cover
Display & function buttons
Dust bin compartment release button
Front view
Ultrasonic sensors
Obstacle detecting sensor window Detecting
sensors of home station & Receiving sensors of
remote controller
Rear view
Main Power switch
Ventilation port
Bottom view
Cliff detection sensors
Side brush
Charging terminals
Brush
Wheel
Battery housing
Lower camera sensor
(Selected models only (VR627*Ser.))
s Figures can be different from actual objects.
8
PART DESCRIPTION – HOME STATION / DUST BIN
Home station
Remote controller holder
Charging terminals
Power switch
Power cord fixing hook
Dust bin
Dust bin handle
Cleaning brush
Dust bin lid
Suction port flap
Sponge filter
Dust bin lid
opening button
HEPA filter
Filter cover
s Figures can be different from actual objects.
9
BUTTON FUNCTIONS – ROBOT CLEANER
TURBO
START/STOP
HOME
10
• If the button is pressed, ‘Turbo Mode’ will be set with a voice confirmation.
• If the button is pressed whilst in ‘Turbo Mode’, it will be canceled.
• Used to turn the power on from Standby, start or stop cleaning.
• If the button is pressed whilst the unit is powered ON, it will start cleaning.
• If button is pressed during the cleaning, it will stop the cleaning.
• If the button is pressed for about 2 sec. whilst the power is ON, the power will be
returned to Standby.
• If the button is pressed in 'Smart Diagnosis' mode, it will end the diagnosis.
• Used to return the Robot Cleaner back to the home station for charging.
• If cleaning is finished or the battery is low, the Robot Cleaner will return to the
Home Station by itself to recharge its battery.
BUTTON LOCK
On/Off
• Pressing the ‘Turbo' and 'START/STOP' button for 3 seconds will activate or
deactivate the Lock function.
• If 'Lock' is ON, a voice announcement "Key lock has already been set" will be heard
each time a button is pressed.
Voice Alert
On/Off
• Press and hold both the Start and Home button on the main unit for 3 sec. to turn
ON/OFF the Voice Alert.
• If the Voice Alert is OFF, the Mute lamp will be ON.
BUTTON FUNCTIONS – REMOTE CONTROLLER
Start
Pressing this button will
start the cleaning. (p17)
Mode
Change the Cleaning Mode of
the Robot Cleaner to ZigZag
Mode.(p19)
Directional button
This button enables Manual
Operation and selection
of an area in 'My Space
cleaning' mode.
Repeat
This button allows activating
or deactivating 'Repeat
Cleaning' mode. (p21)
Home
Used to recharge the Robot Cleaner by
making it return to the Home Station.
(p18)
Turbo
Used to activate or deactivate
'Turbo' mode. (p21)
Stop/OK
Pressing the button will stop the
Robot Cleaner.
My Space
Used to put the Robot Cleaner in
'My Space clean' mode. (p20)
Mute
Used to activate or deactivate
'Mute' mode. (p12)
Diagnosis
Used to run Smart Diagnosis.
Available only when Robot Cleaner
is recharging. (p24)
Tip
• Remote Controller does NOT provide a Power ON function.
• With the machine's power OFF, the Remote Controller will not work.
• To turn the power ON/OFF, use the 'Start/Stop' button on the upper section of the Robot
Cleaner.
• The ‘Mode’ and ‘My Space’ button can only be used after stopping the Robot Cleaner or whilst it
is charging on the Home station.
11
DISPLAY STATUS INFORMATION
Turbo Mode icon
This indicates the settings
for Turbo Mode.
Operational Status icon
This indicates the
operational status of Robot
Cleaner.
Repeat Mode icon
This indicates the settings
for Repeat Mode.
12
Homing icon
This indicates the
conditions of Homing
and Charging.
Mute icon
This indicates the settings
for Voice Alert.
BEFORE YOU START
Check these items before cleaning
• Do not use this device in a room where a child is left alone. The child could be injured.
• Remove fragile or unnecessary objects from the room to be cleaned.
Especially, remove expensive ceramics and valuables from the floor.
• Close the cover of the dust bin compartment before cleaning.
• Remove any moisture that might be on the floor.
• Remove cables, strips, towels, mats etc. from the floor so they will not get tangled in the brushes.
• Confirm whether the battery charge is sufficient, and if it is low, recharge it.
• Empty the dust bin before or after each clean, or before it becomes full.
• Close the doors of any room that you do not want the Robot Cleaner to enter. During cleaning, the Robot
Cleaner may enter another room and continue cleaning.
• When the Mop plate(Selected models only (VR627*Ser.)) is attached, Robot Cleaner+
– will not be able to go
over thresholds of 5 mm or higher.
If you are not planning to use the mop for cleaning, remove the mop before using Robot Cleaner.
• Before starting the device, it's better to remove carpets that are thicker than 20 mm as they may cause it to
malfunction.
+ –
• Please close any balcony doors as the wheels may get stuck while cleaning.
Loading the remote controller battery
1. Open the battery cover by lifting the rear hook of the remote controller.
2. Insert two AAA batteries, checking for +, - nodes while loading.
3. Close the battery cover completely so that the batteries will not fall out.
– +
+ –
Precautions while using the remote control
• Only press one button at a time.
• Do not drop or subject it to any impact.
• Do not store it near devices that give off heat, fire or hot air.
• Certain fluorescent lamps, such as the three band radiation lamp, can interfere with the activation of the
remote control. Therefore, use it as far away as possible from such lamps.
• If the remote control is far from the Robot Cleaner when activated, it may fail to operate properly.
Use the remote within 3 m of the Robot Cleaner if possible.
– +
13
OVERVIEW
1
Install the home station. (p15)
2
Turn on the power supply of the Robot
Cleaner. (p16)
Turn ON the power switch on the rear-left of
Robot Cleaner, and press the 'Start/Stop' button
on the top.
※ If the power supply is not turned on, refer to
page 16.
3
Check the dust bin.
4
Start cleaning. (p17)
5
Automatic charge. (p18)
6
Use the cleaning mode and auxiliary functions.
(p19~22)
< Warning >
14
Insert the power cord plug into an outlet and locate the
station against a wall. If power is not supplied to the
home station, the Robot Cleaner will not charge.
1.5 
1.5 
2
‫ ﻣﺘﺮ‬1.5
‫ ﻣﺘﺮ‬1.5
‫ ﻣﺘﺮ‬2
Check the cleanness of the dust bin before starting
cleaning and close the dust bin compartment cover on
the main unit.
Press the START/STOP button once again while
the Robot Cleaner is turned on. You will hear an
announcement of the cleaning mode and cleaning will
begin once the Robot Cleaner has reversed and turned
around.
The Robot Cleaner will self-diagnose and automatically
return to the home station to recharge before the
complete discharge of the battery. It takes approximately
three hours to charge the battery.
Use the buttons on Robot cleaner and Remote Controller
to use each cleaning mode and supporting features.
For Cleaning Mode, you can choose among ZigZag, My
Space, and Repeat; for secondary features, Manual and
Microfibre Mop (Selected models only (VR627*Ser.)).
W
hen the Robot Cleaner is operated with the dust bin compartment lid left open,
it can cause an injury or serious damage to the product.
HOW TO INSTALL THE HOME STATION
How to Install the Home Station
1. Position the home station against a wall on hard level flooring
to prevent sliding during docking.
Remove objects within 1.5 m to the right and left side and within 2 m
to the front.
1.5 
1.5 
2
2. Plug the power cord into an outlet.
Wrap the remaining power cord around the fixed hook on the back
side of the home station or along the wall surface so that the travel
path of the Robot Cleaner will not be obstructed.
‫ ﻣﺘﺮ‬1.5
‫ ﻣﺘﺮ‬2
‫ ﻣﺘﺮ‬1.5Fixing hook of power cord
3. Fix the home station against the wall so that it does not move.
Then turn on the power switch.
4. When the remote controller is not used, store it in the remote
controller holder on the home station.
Tip
• Always keep the home station plugged in when in use. If the home station is not plugged in, the
Robot Cleaner will not return to the station to charge automatically.
< Warning >
D
o not operate the Robot Cleaner if the Home Station has a damaged cord or
plug, if it is not working properly, or if it has been damaged or dropped. To avoid
electrical hazards, the cord must be replaced by LG Electronics, Inc. or a qualified
service person.
15
HOW TO TURN THE ROBOT CLEANER POWER SUPPLY ON & OFF
Turning on the main power supply
Make sure the Power Switch is on at the rear-left of the Robot
Cleaner.
If the power is OFF, turn the switch ON.
hen turning on the power switch, do not press or touch any
※W
button located on the upper section of the Robot Cleaner. Button
operations can be delayed.
※ Turn off the power switch if the Robot Cleaner is not used for
a long period of time in order to protect the battery. The Robot
Cleaner cannot charge if the main switch is in the "OFF" position.
Turning on from Stand By power.
With the Standby power of the Robot Cleaner OFF, press 'Start/Stop'
button for 1 second until a "Ting" sound is heard. In about 10 seconds,
the power will be on and a melody will sound.
※ If 10 minutes elapse without the Robot Cleaner having being
given an active command after being turned on, the power will
automatically return to Standby again.
Turning off the power supply
Press and hold the START/STOP button for two seconds while
the Robot Cleaner is turned on. A melody will sound when the
power is turned off.
Tip
16
• If the power cannot be turned on, do the following.
- Turn the main power switch OFF, wait 5 seconds then ON again.
- Press the ‘START/STOP’ button after the main power switch has been turned on again.
- If the power is not turned on or if there is no display but only the “Ting” sound,
put the Robot Cleaner manually on to the home station as the battery may be flat.
HOW TO START AND STOP CLEANING
Using the buttons on the Robot Cleaner
After the Robot Cleaner main power switch is turned on, press the
START/STOP button to begin cleaning. A melody will sound and
cleaning will begin.
Press the START/STOP button during the cleaning cycle to stop
cleaning.
※ When the ‘START/STOP’ button is pressed while the power supply of
the Robot Cleaner is in Standby, the power will be turned on. Press
the ‘START/STOP’ button one more time to start cleaning.
Using the remote controller
After the Robot Cleaner is turned on from the Robotic Cleaner, press
the START button on the remote control. A melody will sound and
cleaning will begin.
Press the STOP button during the cleaning cycle to stop cleaning.
※ The Robot Cleaner cannot be turned on from Standby, by using the
remote controller when the power of the Robot Cleaner is off. When
the power is off, press the ‘START/STOP’ button on the upper side
of Robot Cleaner to turn the power on and to allow the remote to
be used.
※ During cleaning, collisions can happen when the sensor cannot detect objects because of their shape (Thin
chairs and table legs, furniture corner). When this happens, the internal impact detecting sensor will react
by using a backward motion.
※ If the Robot Cleaner is set to start cleaning at a location away from the home station, put the Robot
Cleaner on a flat floor in order to prevent a malfunction of the obstacle detecting sensor. In addition, start
cleaning from a location where there are no obstacles. For example, curtains or walls must be 30 cm from
the Robot Cleaner.
Tip
For best results:
• Briefly scan the area to be cleaned for big and small objects that will cause difficulty for the
Robot Cleaner.
• If cleaning is started when the Robot Cleaner is at the home station, the device can rapidly be
returned to the home station as the current home position has been accurately read.
• When the Mop plate(Selected models only (VR627*Ser.)) is installed, to prevent a 2nd
contamination from the contaminated mop, it will not go over door sills of 5 mm or higher.
17
HOW TO CHARGE THE BATTERY
Automatic charging
The Robot Cleaner returns to the home station at the end of a cleaning cycle
or when its battery is running low.
※ If 10 minutes elapse without the Robot Cleaner moving or the battery is
too low, the power will be automatically turned OFF.
※ Do NOT turn OFF the Main Power Switch as the battery will not be
recharged. If the machine is returned manually with the Main Power
Switch OFF, it announces an error message, "Main power switch on the
back of the Robot cleaner is turned off. Please turn the switch on."
※ In the event that the unit returns to the Home Station due to a low battery
during the cleaning, cleaning will be started, after recharging, from the nearest place of the area which has not
been cleaned before.
※ If Robot Cleaner is unable to dock to the home station on its first attempt, it will try again until it docks successfully.
※ When Robot Cleaner has completed all areas that it can clean, it will return to the home station even when the
battery level is not low.
Manual charging
You can manually charge the battery prior to using the Robot Cleaner for the first time or to charge the
battery during cleaning.
Method 1. A
ttach the Robot Cleaner to the home
station by aligning to the front side of
the home station. A melody sound will be
generated along with an audio message to
start charging.
※ If a voice message, "Main power switch on
the back of the Robot cleaner is turned off.
Please turn the switch on." is announced
repeatedly, then turn on the Main Power
Switch.
Method 2. W
hen the 'HOME' button of the remote
control or the Robot Cleaner is pressed,
charging will be prompted by automatically
generating a searching signal and returning
the Robot Cleaner to the home station.
※ If the Robot Cleaner did not start cleaning from the home station or if the Robot Cleaner is manually
charged by pressing the Home button, it may take slightly longer to find the home station.
※ If the Robot Cleaner is within 10 cm of the front of the charging terminal while the power is turned on from
Standby, it will automatically be returned to the home station and charging will begin.
Tip
18
Take the following precautions when using the home station:
• If foreign material is caught on the charging terminal, charging may not be activated. Wipe the
terminal from time to time with a dry cloth after the power plug is disconnected.(p29)
• To prevent electric shock or damage to the home station, do not touch the charging terminal
with any metallic objects.
• To avoid fire or electric shock, never disassemble or modify the home station.
• Do not to place the Robot cleaner, the home station or power plug near a heating source.
CLEANING MODES
Zigzag Cleaning
In 'Zigzag' mode, Robot Cleaner repeats a zigzag
operation to clean each and every spot in the cleaning
area.
If you need to quickly clean an area choose 'Zigzag' mode.
Press ‘Mode’ button on Remote Controller to select
'Zigzag' mode and press 'Start' button.
※ Factory release default setting is 'Zigzag'.
Manual Cleaning
By pressing a direction key on the Remote Controller, you can move Robot Cleaner in a Manual mode.
Robot Cleaner will clean the area, moving forward/backward/left/right, according to the input of the direction
key.
While in 'Manual' mode, the robot cleaner will run into obstacles placed behind it if the backward key on the
remote remains held down.
19
CLEANING MODES
My Space Cleaning
Pressing 'My Space' on the Remote Controller will set the My Space cleaning
mode with a voice message. For cleaning of particular spaces, select this mode.
The 1st stage:
Use the Remote Controller to manually set the parrameters of each cleaning
block.
※ This cleaning mode will be accepted when the distance of the start and end
position is less than 1 m.
My Space
The 2nd stage:
Pressing the 'Start' button will then make the Robot Cleaner clean the manually outlined area by itself.
※ Upon failure to correctly outline a zone, a voice will announce, which says "Area does not meet the specified
conditions. Please continue to make specified area for cleaning process."
Use the Remote Controller to assign a zone, again.
※ When My Space cleaning is completed, the mode is switched to Auto Clean (ZigZag).
Tip
20
• While recharging, you cannot activate 'My Space clean' mode.
• To change the cleaning mode while the Robot Cleaner is in operation, press 'Stop' button first
then select a cleaning mode. The cleaning will then start from the begining.
AUXILIARY CLEANING MODES
Turbo Mode
Pressing the 'Turbo' button on the Remote Controller
or main unit will activate 'Turbo' mode, with a voice
message.
While in 'Turbo' mode, pressing the same button will
cancel 'Turbo' mode, with a voice message.
In 'Turbo' mode, Robot Cleaner runs more intensely for
a powerful clean. Mode mode will reduce the battery
duration.
Repeat Mode
Pressing 'Repeat' button on Remote Controller will activate 'Repeat' mode,
with a voice message. While in 'Repeat' mode, pressing the same button will
cancel 'Repeat' mode, with a voice message. In 'Repeat' mode, Robot Cleaner
repeats the cleaning in progress until the battery runs out without returning
to the home station.
Learning Mode
The Robot Cleaner is capable of memorising the
cleaning environment through its Learning mode for
an intelligent cleaning operation.
※ 'Learning Mode' is available only when the machine
starts cleaning from the Home Station.
Tip
• Precautions with Smart Operation
- This Learning mode enables memorizing locations with obstacles to help bypass them. Robot
Cleaner memorizes every aspect of the environment it was subjected to from when it started
cleaning from the Home Station to the moment it finishes its course.
- Robot Cleaner learns new conditions again when the location of Home Station has been
changed.
- If the learning mode is accepted, a voice message will say "Environment has been studied by
learning process."
21
MOP CLEANING (Selected models only (VR627*Ser.))
By attaching the ultra microfiber mop, you can
effectively use the Robot Cleaner to remove dust on
hard floor surfaces.
When the mop plate is attached, the Robot Cleaner
will not climb on to carpets or over thresholds, in
order to prevent transferring dirt from the mop.
Caution
Do not cover the bottom
camera sensor by mop.
For mop cleaning, mount the mop and mop plate to the Robot Cleaner according to the following instructions:
1. Attach the ultra microfiber mop to the Velcro
of the mop plate as shown in the figure.
2. Firmly slide the Mop Plate into the furrows
until you hear a 'click' sound.
※ Note that, if the Mop Plate is not secured
correctly, it may separate during the
cleaning.
“Click!”
Fixing hook
Fixing groove
3. It is essential that the fixing hooks on the
Mop Plate align correctly on to the fixing
grooves on the underside of the cleaner.
Tip
22
• To avoid odors, wash any foreign material or dust off the mop after cleaning is completed.
• To avoid staining floors, do not use the ultra microfiber mop to clean when dirt is contaminated
with liquids such as coffee or ink.
• To avoid damage to carpets from the Velcro or dirt transfer from the mop, do not attempt to
clean the carpet while the mop plate or mop is attached.
• Keep the ultra microfiber mop dry. Do not use it on wet surfaces.
If there is moisture on the floor, it can interfere with the navigation and damage the unit.
• Smart Diagnosis feature is not available, when the Mop Plate is attached.
• Some models may not come with Microfibre Mop or Mop Plate.
LOCATION SEARCH FUNCTION
The Robot Cleaner remembers its location while cleaning.
If the user moves the Robot Cleaner while it is operating, it will search for the location it was
moved from by using its navigational location search function before continuing to clean.
※ The navigating function will be activated after the Robot Cleaner
adequately recognizes the cleaning environment.
Change location
Manual Relocation.
1. With the power off, locate the Robot Cleaner near
the location where it was originally moved from.
※ The location search is more effective when the
Robot Cleaner is closer to the location where it
was moved from.
※ If it is moved from its original cleaning position
by more than 1 m, it becomes difficult for
the Robot Cleaner to search for it's previous
location.
1m
1m
Location of incident
2. Press the START/STOP button on the Robot Cleaner or START button on the remote controller.
Robot Cleaner will then start the location search function along with an audio guide.
※ When the location search is successfully completed, it will continue cleaning from where it was moved.
If the location search fails, it will start again from the beginning.
To find exact location,
please step away from
the Robot cleaner.
Location of incident
Tip
• If the power is turned off after the location search function is set, the location search function
will be canceled.
• L ocation search will be more effective when the Robot Cleaner is closer to the location where
it was moved from.
23
SMART DIAGNOSIS
Robot Cleaner uses this Smart Diagnosis feature to run a self-diagnosis.
If any irregularity is found from the diagnosis, please contact the local LG Electronics service center.
※ During Smart Diagnosis, the Robot Cleaner will move about within a 50 cm radius. So, make sure no objects are in the way
within a 1 m radius around the Home Station, before starting Smart Diagnosis.
1. S mart Diagnosis will operate when the main power switch of the
Robot cleaner and the Home station are turned on, and the unit
docked on the Home station.
※S
mart Diagnosis is only possible when the Robot Cleaner
is attached to the Home Station.
2. P
ress 'Diagnosis' button on the Remote Controller, then the process
will start with a voice message which says "Robot cleaner smart
diagnosis will be started. Please step away and clear around 1 meter
around the home station."
※ If the Mop Plate(Selected models only (VR627*Ser.))
is attached, the process will not be activated.
3. W
hen the Smart Diagnosis has successfully finished, Robot
Cleaner will return back to the Home Station and inform the
result through a voice message. After the voice message,
pressing the 'HOME' button on the Remote Controller or
main unit will allow the voice message to be repeated. To
terminate the diagnosing process, press the 'Stop' button on
the Remote Controller or main unit.
※A
fter the Smart Diagnosis voice message, the Robot
Cleaner will start recharging after 1minute.
※ If an error is detected with any of the Sensors whilst
in Smart Diagnosis, a voice message will announce,
and the unit will not return to the home station.
Tip
24
• Be careful not to touch the Robot Cleaner or disturb its operation before Smart Diagnosis is
complete.
If it is accidently interrupted, turn the main power switch OFF then ON again to resume the
diagnosis.
• Smart Diagnosis will not be activated in each of the following cases.
In each case, check the problem and try again.
- Robot Cleaner is detached from Home Station
- Battery level is insufficient
- No Dust Bin Filter is fitted.
- Mop Plate(Selected models only (VR627*Ser.)) is attached
SMART DIAGNOSIS
If a voice message is announced after Smart Diagnosis, refer to the following table to take proper actions.
Voice message
Robot Cleaner smart diagnosis will be started. Please
step away and clear around 1 meter around the home
station.
Smart diagnosis can start when it is being charged. Please
dock Robot Cleaner to the home station to charge.
No defect found during diagnosis.
Diagnosis mode cannot be operated due to a low battery.
Please try again after the battery is charged.
Please check if the dust bin is installed with the filter.
Charging cannot be done due to a problem in infrared
sensor.
Charging cannot be done due to a problem in ultrasonic
sensor.
Charging cannot be done due to a problem in the cliff
detection sensors on the bottom. Please clean the
sensors.
Please wipe the obstacle detecting sensor window on the
left and right side of the Robot Cleaner.
A problem has been found on the Gyro Sensor.
Please check for dirt on the left wheel.
Please check for dirt on the right wheel.
A problem has been found on the left wheel sensor.
A problem has been found on the right wheel sensor.
Please check the brushes for obstructions.
A problem has been found in the suction motor.
A problem has been found in the acceleration sensor.
In order to listen to the smart diagnosis result again,
please press the charging button. To stop, please press
the stop button.
Please try smart diagnosis again after turning the main
power switch off and on from the back of Robot Cleaner.
If the problem continues, please contact LG Electronics
customer care.
Smart diagnosis mode will be turned off.
Smart Diagnosis mode cannot be operated with mop
plate being attached. Please try again after removing it.
Smart diagnosis has failed to operate. Please try it again
after turning off and on the main power switch on the
back of the Robot Cleaner.
Measures (for reference)
Clear any object within a 1 m radius around Home Station,
and stay back until the diagnosis is complete.
Move Robot cleaner to the Home Station to recharge it.
Try the Smart Diagnosis again after recharging the battery.
Open the Dust Bin Cover and examine the bin.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Clean the three Cliff Sensors on the bottom at the front of
the unit.
Clean the lens of the Obstacle Sensors on both the left and
right hand sides.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Check for foreign materials on the left wheel.
Check for foreign materials on the right wheel.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Check for any foreign material stuck in the Brush.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
Run Smart Diagnosis again and, if the same message is
announced, contact an LG Electronics service center.
If you need to repeat the diagnosis result, press the 'Home'
button, or press 'Stop/OK' button to finish the diagnosis.
Run Smart Diagnosis again after removing the Mop Plate.
Turn the main power switch OFF and then ON again to
resume the diagnosis. Do NOT touch the robot or disturb
its operation until the diagnosis is complete.
25
CLEANING THE DUST BIN
If the dust bin is full, suction power can be reduced. Clean the dust bin before or after each cleaning session.
Clean the dust bin using the following sequence:
1. Open the dust bin compartment cover by pressing
the PUSH button on the Robot Cleaner.
2. Grab the handle of the dust bin and pull it upward.
3. Pull the hook on the left of Filter Cover on the
rear of Dust Bin to separate the filter and the
sponge.
※ Note that separating the filter may result in
dust dropping.
※ Refer to p.27 when cleaning the Dust Bin Filter.
4. Lift the dust bin lid upward while pressing the
separation button on the dust bin.
5. Empty the dust bin and clean it with a cleaning
brush or under running water.
6. After cleaning with water, completely dry the
dust bin in a well-ventilated area out of the direct
sunlight.
7. When reassembling or fitting the cleaned Dust
Bin, close the lid and put in the Sponge and HEPA
Filter.
※ Refer to p.27 for detailed assembly guides.
8. Put the dust bin into the Robot Cleaner and close
the dust bin compartment cover.
Tip
26
• Operating the unit without Filters fitted to the dust bin can cause a motor malfunction not
covered by warranty.
• After cleaning the Dust Bin, make sure to assemble the filter and fit it to the Dust Bin.
If you initiate cleaning, with no filters fitted to the dust bin or Filter Cover not assembled, a
voice message will be announced which says "Please check if
the dust bin is installed with the filter."
• Always ensure that the dust bin lid is refitted correctly after
cleaning the dust bin so that it closes easily and accurately.
CLEANING THE DUST BIN FILTER
The Dust Bin Filter consists of a HEPA Filter and Sponge Filter.
Clean both the HEPA and Sponge filters as per the following sequence.
1. Pull the hook on the left of the HEPA Filter
module on the rear side of Dust Bin to separate
the HEPA Filter and the sponge.
2. Thoroughly clean out the fine dust particles on the
HEPA Filter, with a vacuum cleaner or cleaning brush.
※ Do NOT wash the HEPA Filter with water.
Its suction power will be reduced.
3. Use a cleaning brush to clean the Sponge Filter.
If using water to clean it, allow it to dry completely
in the shade before refitting.
4. Assemble the HEPA and Sponge filters back onto
the Filter housing as per the following sequence.
※ Fit the rectangular locator on the HEPA Filter
into the locating slot of the filter body.
※ Be careful not to incorrectly assemble HEPA
and Sponge Filter onto the Filter housing.
Tip
• To preserve the performance of the Robot Cleaner, clean the HEPA Filter at least once a week,
with a brush or vacuum cleaner.
• The HEPA and sponge filters must be fitted to the filter housing before refitting the filter to
the dust bin. Operating the Robot cleaner without the HEPA and sponge filters will cause the
suction motor to malfunction.
27
CLEANING THE BRUSH
The rotating Brush, located on the bottom of Robot Cleaner, helps collect the dust. Clean the Brush as per the
following sequence.
※ Before turning over the main unit, lay a soft cloth on the floor and remove the Dust Bin.
Otherwise, the main unit can get scratched and dust will fall from Dust Bin.
Turn the Main Power Switch
OFF before starting the clean.
Put the Robot Cleaner upside
down on a soft cloth.
After checking for foreign
materials, press down the Fixing
Hook and pull it up to separate
the brush Cover.
By using the cleaning tool,
clear hairs and other debris
and foreign materials on the
Brush and from the 2 smaller
jockey wheels.
Push the Brush all the way
into the yellow protrusion.
While pushing the Brush, lift
the white protrusion part up to
separate it from the main unit.
Carefully clean the Brush with
a vacuum cleaner or scissors.
Fit the Fixing Hook (rectangular
shape) on the side of the Brush
into the slots, with the colors
matching.
28
While pushing the Brush to the
arrow direction, fit the Fixing
Hook (rectangular shape) on
the opposite side into the slot.
Press down and close the Cover
until a 'crack' sound is heard
from both sides of Fixing Hook.
※ Be careful not to trap the side
brush bristles under the cover
when closing it.
CLEANING THE SENSORS/CHARGING TERMINALS
There are sensors on the Robot Cleaner that detect obstacles, stairways
and the home station for charging the battery. In order to maintain
the performance of the Robot Cleaner, regularly clean the sensors and
charging terminals as follows:
1. Turn off the power switch on the rear side of the Robot Cleaner. Injury
can be caused by the activation of the Robot Cleaner if the main power
is not turned off.
2. Lay a smooth cloth on the floor, turn over the Robot Cleaner and put it
on the cloth.
※P
lease make sure to remove the dust bin before rotating the main
body. Otherwise, the dust in the dust bin may fall out.
3. Use a smooth cloth or cleaning brush to wipe the dust off each of the 3 cliff sensors, camera sensors and
ultrasonic sensors and the charging terminal as described below.
Ultrasonic sensors
Upper camera
sensor
Obstacle detecting
sensor window
Detecting sensors
of home station &
Receiving sensors of
remote controller
Cliff detection
sensors
Charging terminals
Charging terminals
Lower camera sensor
(Selected models
only (VR627*Ser.))
Lens
Tip
• Do not clean the Robot Cleaner by directly spraying it with water, thinners, solvents, benzene,
or any other liquids.
• Call the service center if the sensor or charging terminal is damaged.
Sensor and terminal damage can cause the product to malfunction.
• To clean the sensor/charging terminals, use the cleaning brush.
• Some models may not have a Camera Sensor, on the bottom.
29
CLEANING THE SIDE BRUSH
Foreign objects/materials such as hair can easily adhere to the side brush.
Remove such materials at least once a week.
If excessive amounts of foreign materials are stuck to the brush, there is
the risk of damage to the brushes.
If the floor is rough or frequently cleaned, the side brushes may bend or become damaged.
In this case, use the following method to straighten the side brush.
1. The following procedure is helpful in restoring
deformed brushes.
2. Turn off the power by switching the main switch
off on the rear off the unit.
3. Place the Robot Cleaner at the end of a table to
make cleaning the side brush easier. Make sure
that the Robot Cleaner is not in danger of falling.
4. Soak the side brush in warm to hot water.
5. Press down on the side brush for about ten
seconds so that it is completely submerged in the
water.
6. Slowly wipe the side brush by sliding it through
your hand.
7. Rotate the side brush and repeat steps 4-6 for
each section of the brush.
8. Use te side brush only after it has completely
dried.
Side Brush management
1. Remove the screws by using a suitable screw driver
and separate the Side Brush from the main unit.
2. Remove any hair after the separation.
3. Assemble the Side Brush by replacing it onto the
bottom of the Robot Cleaner, with the 'R' and 'L'
marking of the Brush matching the counterparts on
Robot Cleaner.
30
CLEANING THE ULTRA MICROFIBER MOP (Selected models only (VR627*Ser.))
To avoid odors, dirt and dust should be washed off the mop after it is used for cleaning.
Follow these directions to wash the ultra microfiber mop:
1. Separate the ultra microfiber mop from the mop plate.
210 mm
2. Carefully clean it with warm water.
3. Use the Mop after completely drying it in direct sunlight.
※ If the Mop is used in a damp or wet state,
it will cause the Robot Cleaner to malfunction.
Tip
• To avoid product malfunction, only use the ultra microfiber mop provided with the Robot
Cleaner.
• Additional microfiber mops can be purchased by visiting a nearby LG Electronics service center.
• Some models may not come with Microfibre Mop or Mop Plate.
31
TROUBLESHOOTING
Upon a voice message, "The wheels are not touching the floor. Please move
Robot cleaner onto flat floor."
A warning message will be given if a wheel does not contact the floor surface for any reason.
• Is a wheel trapped in the front door, balcony, stairway, etc?
s Move the Robot Cleaner on to the flat floor.
Upon a voice message, "Please remove foreign material on the left/right
wheel."
• Is any foreign material wound around the wheel?
s Turn off the main power switch on the rear side of the Robot cleaner.
Then lay a soft cloth on the floor, turn over the Robot Cleaner, and put it on the cloth.
Remove foreign material after observing the wheel.
※P
lease make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
Upon a voice message, "Robot cleaner cannot continue cleaning. Please
check the area around Robot Cleaner."
A warning message will be given if Robot Cleaner cannot go on cleaning due to any unfavourable condition.
• Is the Robot Cleaner stuck?
s After removing it from the obstacle, place the Robot Cleaner on flat floor.
32
TROUBLESHOOTING
Upon a voice message, "Please check if the dust bin is installed with the
filter."
A warning message will be given if there is no Dust Bin or Filter housing fitted.
• Is the Dust Bin fitted to the Robot Cleaner?
s Open the Dust Bin compartment cover and check to ensure the Dust Bin is in place.
s Do NOT leave the Dust Bin Cover open.
• Make sure the Filter housing is assembled onto the Dust Bin.
Upon a voice message, "Battery is low. Please move Robot cleaner onto
the home station to charge."
When the remaining amount of battery power is almost nil, the voice, “Battery is low”, is generated.
• Initiate battery charging of the Robot Cleaner by moving it to the home station.
s When the Robot Cleaner is attached to the docking station successfully, it will start the recharging with
the recharging start melody.
33
TROUBLESHOOTING
Upon a voice message, "Please remove foreign material from the brush on
the bottom."
A warning message will be given if foreign materials restrict the Brush's rotation.
Turn off the main power switch on the rear of the Robot Cleaner.
Lay a soft cloth on the floor and put the Robot Cleaner upside down on it.
※ Before turning over the main unit, remove the Dust Bin. Otherwise, it will cause dust to fall from Dust
Bin.
• The brush is making a loud, abnormal sound.
s Confirm the correct assembly of the brush by checking the separation groove of the brush
s Remove the lower rotating brush from the Robot Cleaner and remove any foreign material from the brush.
1
2
3
5
4
• The lower rotating brush or side brush is stuck.
s Remove any foreign materials such as cables, thread of hair caught in the side brush or the lower rotating
brush.
※ For a more detailed description of this process, refer to the instructions on page 28, 30.
34
BEFORE YOU CALL FOR SERVICE
Confirm before reporting the failure of Robot Cleaner.
Problem
Solutions (Reference page)
The power supply cannot
be turned on.
Check that the power switch is turned on. (Page 16)
The power supply
automatically turns off.
This is not a failure. Robot Cleaner has its own power saving function.
If it is not used for ten minutes after the power supply is turned on, the
power will automatically turn off. (Page 18)
The Robot Cleaner will not
charge.
ƬƬ Check whether the main power switch is turned on.
ƬƬ Remove objects around the home station. (Page 16)
ƬƬ Confirm that the power supply is connected to the home station.
(Page 15)
ƬƬ Wipe the charging terminals with a dry cloth.
Suction power becomes
weak.
ƬƬ Check whether there is foreign material blocking the suction port.
(Page 28)
ƬƬ Empty the dust bin. (Page 26)
ƬƬ Clean the dust bin filter. (Page 27)
Noise becomes louder.
ƬƬ Confirm that the dust bin has been mounted properly.
ƬƬ Confirm that the dust bin filter has been mounted properly. (Page 27)
ƬƬ Check whether foreign material is caught in the brush. (Page 28)
The Robot Cleaner will not
activate.
ƬƬ Confirm that the power switch is turned on. (Page 16)
ƬƬ Confirm that the battery has been charged. (Page 18)
The lower brush does not
rotate.
ƬƬ Clean the brush. (Page 28)
ƬƬ Confirm that the brush has been mounted properly. (Page 28)
Movements or travel path
are abnormal.
ƬƬ Carefully wipe the sensors with a dry soft cloth. (Page 29)
ƬƬ If the ultra microfiber mop is attached,
confirm that it is mounted properly. (Page 22)
ƬƬ Turn the main power switch off and on.
The Robot Cleaner cannot
be activated with the
remote control.
ƬƬ Replace the remote control batteries. (Page 13)
ƬƬ Confirm that the control is within the coverage area of the main unit,
which is less than 3 m. (Page 13)
ƬƬ Check whether the main power switch is turned on. (Page 16)
35
PRODUCT SPECIFICATIONS
36
Item/Model
LG Robot Cleaner
VR634** Ser, VR644** Ser,
VR635** Ser
External Dimensions
340 mm × 340 mm × 89 mm
Weight
3 kg
Power Consumption
18 W
Battery (Fully Charging)
DC 16.8 V
Traveling Velocity
350 mm/s (Maximum)
Use Time
Approx. 100 minutes
(Based on general wooden floor)
Charging Time
3 hours
Main Functions
Turbo Mode
Learning Mode
Obstacle Sensing
Anti-Plunge function
Error Displaying
Navigation
Auto/Manual Recharging
Dry Mopping (cleaning)
(Selected models only (VR627*Ser.))
Corner Clean
Voice Messaging
Map Drawing
Repeat Cleaning
My Space Cleaning
Zigzag Cleaning
Item/Model
Home Station
External Dimensions
236 mm × 181 mm × 128 mm
Rating
240 V~ 50 Hz
Output Voltage/Current
DC 17.1 V / 1.1 A
Power Consumption
23 W
Item/Model
Battery
Type
Lithium Battery
Rating
DC 14.4 V / 2200 mAh / 4 cells
REFERENCE ITEMS
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
Removing / Refitting the battery pack
1
2
Turn off the main power switch
on the back-left side of the Robot
Cleaner.
6
Place a soft cloth on the floor,
remove the dust bin, and flip
the Robot Cleaner over.
5
Refit the battery in the reverse
order.
Separate the wire from the
battery while pressing the
connector hook.
3
Remove the screws by using a
Phillips head screwdriver.
4
Remove the battery from the
device.
WARNING
Please be careful of fire, explosion, electric shock, or breakdown.
• Do not charge this Battery Pack(Pack hereafter) with any other type of charger other than the one
originally provided with the Robot Cleaner.
• Do not damage the battery pack in such ways as dropping, crushing, cutting, or shorting extemal contacts.
• Do not attempt to disassembly the battery pack under any circumstances. When the Pack is damaged or
malfunctioning, bring it and the Robot cleaner and Home station to an authorised service center.
• Do not place the battery pack near a heat source or do not dispose of in fire or water.
• Please keep the battery pack away from any damp or wet environment when the pack is charged.
• Please keep away from children, infant or pets.
37
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled bin symbol is attached to batteries/accumulators of Your product it means they
are covered by European Directive 2006/66/CE.
2. This symbol may be combined with chemical symbols for mercury(Hg), cadmium(Cd) or lead(Pb) if the battery
Contains more that 0.0005% of mercury, 0.002% of cadmium or 0.004% of lead.
3. All batteries/accumulators should be disposed separately from the municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
4. The correct disposal of Your old batteries/accumulators will help to prevent potential negative consequences for
the environment, animal and human health.
5. For more detailed information about disposal of Your old batteries/accumulators, please contact Your city office,
waste disposal service or the shop where You purchased the product.
Disposal of your old appliance
1. All electrical and electronic products should be disposed of separately from the municipal waste stream via
designated collection facilities appointed by the government or the local authorities.
2. The correct disposal of your old appliance will help prevent potential negative consequences for the environment
and human health.
3. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal
service or the shop where you purchased the product.
Made in Korea
Download PDF