LG TA106 Owner's manual
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
SLOVENŠČINA
PORTUGUÊS
TA106 (TA106, TAS106F)
ΕΛΛΗΝΙΚΑ
Please read this manual carefully before operating
your set and retain it for future reference.
ESPAÑOL
Micro Hi-Fi System
ITALIANO
OWNER’S MANUAL
1
Getting Started
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
yy The appliance is not intended for use by young
children or infirm persons without supervision.
yy Young Children should be supervised to ensure
that they do not play with appliance.
yy If the appliance is supplied from a cord
extension set or an electrical portable outlet
device, the cord extension set on electrical
portable outlet device must be positioned so
that it is not subject to splashing or ingress of
moisture.
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
4
Table of Contents
Table of Contents
1
Getting Started
2
6
6
6
6
6
6
7
8
9
Safety Information
Unique Features
Accessories
Playable file Requirement
– MP3/ WMA music file requirement
– Compatible USB Devices
– USB device requirement
Remote control
Front panel
Rear panel
2 Connecting
10
10
10
10
11
11
11
12
12
Connecting to speakers
– Attaching the speakers to the unit
System cable Connection
– AUX IN Connection
Optional Equipment Connection
– PORT. IN Connection
– Video Connection
– USB Connection
– Antenna Connection
3 Operating
13
13
13
13
13
13
14
14
14
14
14
14
15
15
15
16
16
17
17
17
17
18
18
19
19
19
Basic Operations
– CD/ USB Operations
Other Operations
– Programmed Playback
– Displaying file information
(ID3 TAG)
– Turn off the sound temporarily
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Improving poor FM reception
– Seeing information about a Radio
station
Sound adjustment
– Setting the surround mode
– Adjusting the sound
Setting the Clock
– Using your player as an alarm clock
– Sleep Timer Setting
– Dimmer
Advanced Operations
– Playing the iPod
– Compatible iPod
– Listening to music from your external
device
– Recording to USB
– Pausing recording
– To select recording bit rate and speed
Table of Contents
5
4 Troubleshooting
20 Troubleshooting
20 – General
1
5 Appendix
21
22
23
23
23
Trademarks and Licenses
Specifications
Maintenance
– Notes on Discs
– Handling the Unit
2
3
4
5
6
Getting Started
Unique Features
USB Direct Recording
Getting Started
Records music to your USB device.
MP3/ WMA music file
requirement
Portable In
Listens to music from your portable device. (MP3,
Notebook, etc)
Accessories
Please check and identify the supplied accessories.
LG EQ
1
OPEN/CLOSE
+
_
MENU
SLEEP
.
TUNING +
TUNING -
1
Playable file
Requirement
ENTER
.
.
CLOCK
TIME
RDS
SET
1
FM Antenna (1)
2
3
4
5
6
7
8
9
MP3/ WMA file compatibility with this unit is limited
as follows :
• Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
• Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
• Maximum files : Under 999
• File extensions : “.mp3”/ “.wma”
• CD-ROM file format : ISO9660/ JOLIET
• We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
0
Remote Control (1)
Compatible USB Devices
• MP3 Player : Flash type MP3 player.
• USB Flash Drive :
Devices that support USB2.0 or USB1.1.
• The USB function of this unit does not support
all USB devices.
Batteries (2)
iPod Cradle (1)
Speaker Cables (2)
AC power cable (1)
USB device requirement
• D
evices which require additional program
installation when you have connected it to a
computer, are not supported.
• Do not extract the USB device while in
operation.
• For a large capacity USB, it may take longer than
a few minute to be searched.
• To prevent data loss, back up all data.
• If you use a USB extension cable or USB hub, the
USB device is not recognized.
• Using NTFS file system is not supported. (Only
FAT(16/ 32) file system is supported.)
• This unit is not supported when the total
number of files is 1 000 or more.
• External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
• USB port of the unit cannot be connected to
PC. The unit cannot be used as a storage device.
Getting Started
Remote control
• • • • • • a • • • • • • 1 (POWER): Switches the unit ON
or OFF.
EQ : Chooses sound impressions.
LG EQ
B
+
_
B OPEN/CLOSE : Opens and
closes the disc tray.
MENU
.
• • • • • • b • • • • • • TUNING +
TUNING -
SLEEP
ENTER
.
LG EQ : Selects a Natural or Local
Specialization equalizer effect by
using LG EQ.
VOLUME +/- : Adjusts speaker
volume.
FUNCTION : Selects the function
and input source.
.
CLOCK
RDS
SET
1
2
3
4
5
6
7
8
9
0
PRESET/FOLDER W/S : Searches
for a folder of MP3/ WMA files.
When a CD/ USB containing
MP3/ WMA files in several folders
is being played, press PRESET/
FOLDER W/S selects to the
folder you want to play. Choose a
‘preset number’ for a radio station.
@ MUTE : Mutes the sound.
• • • • • • c • • • • • • SLEEP: Sets the system to turn off
automatically at a specified time.
(Dimmer : The display window will
be darken by half.)
Battery Installation
INFO. : Checks information about
your music. MP3 files often come
with tags. The tag gives the Title,
Artist, Album or Time information.
REPEAT/MENU :
-- Listens to your tracks repeatedly
or randomly. (only in CD/USB)
-- Move to the desired item.
TUNING -/+ : Selects the radio
station.
Remove the battery cover on the
rear of the Remote Control, and
insert two (size AAA) batteries
with 4 and 5 matched correctly.
C/V (Skip/Search):
-Skips Fast backward or Forward.
-Searches for a section within a
track.
Z ENTER: Stops playback or
recording.
d/M (Play/Pause) : Starts or
pauses playback.
PROG./MEMO. :
-For storing radio stations if you
have saved radio stations using
PROG./MEMO., you can scroll
through them and select one.
-Listens to your tracks in any
order.
X REC: USB direct recording.
• • • • • • d • • • • • • CLOCK : For setting the clock and
checking the time.
TIMER : With the TIME function
you can turn USB, CD play and
TUNER reception on or off at a
desired time.
SET : Confirms the setting.
0-9 numerical buttons: Selects
numbered tracks, files, or preset
number.
1
Getting Started
1
OPEN/CLOSE
7
Getting Started
8
Front panel
a
1
b
c
d
e
Getting Started
1/!
f
B
d/M
Z
FUNC.
C
V
PORT. IN
g
h
i
j
<
- BASS +
a 1/! (POWER)
Switches the unit ON or OFF.
b Disc tray
c Display window
Shows the current status of the unit.
d PORT. IN
Connects to a portable player with audio
outputs.
e B (OPEN/CLOSE)
Opens or closes the disc tray.
d/M (PLAY / PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
Z (STOP)
Stops playback.
FUNC. (FUNCTION)
Changes the input source or function.
- TREBLE +
- VOLUME +
C/V (Skip/Search):
Goes to next or previous file/track.
Searches backward or forward (Press and hold)
Tunes in the desired radio station.
f USB Port
Connects an USB device.
g BASS -/+
h VOLUME -/+
Adjusts speaker volume.
i TREBLE -/+
j <
Headphone jack
Getting Started
9
Rear panel
1
b
Getting Started
a
e
AUX IN
CABLE
iPod
VIDEO OUT
iPod DOCK
L
FM
R
c
ANTENNA
d
SPEAKERS
L
4
POWER IN
5
CABLE
R
f
g
h
a CABLE
e ANTENNA (FM)
b iPod VIDEO OUT
f SPEAKERS
Connects the speaker cables.
c iPod DOCK
Connect to the furnished iPod cradle.
d AUX IN
g CABLE
h POWER IN
10
2
Connecting
Connecting to
speakers
System cable
Connection
Attaching the speakers to the
unit
Your unit consists of two separate parts, CD player
and an integrated Tuner/Amplifier.
Before you can use your unit, the separate parts
must be connected with the system connection
cable.
1. Loosen the knob by turning it counterclockwise.
Connecting
2. Insert the bare part of the wire into the hole in
side of each terminal.
Connect the red stripe of each wire to the terminals
marked + (plus) and the other end to the terminals
marked - (minus).
iPod
VIDEO OUT
>>Caution
iPod DOCK
ANTENNA
L
R
FM
SPEAKERS
L
4
POWER IN
5
CABLE
R
The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
AUX IN
CABLE
3. Tighten the knob by turning it clockwise to
secure the wire.
Connecting
Optional Equipment
Connection
11
Video Connection
Connect the iPod VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
You can hear the sound through the system’s
speakers.
PORT. IN Connection
AUX IN
CABLE
Connect an output of portable device (MP3 or PMP
etc) to the PORT. IN input connector. The portable
cable is not supplied as an accessory.
iPod
VIDEO OUT
iPod DOCK
ANTENNA
L
R
FM
2
Connecting
SPEAKERS
iPod
VIDEO OUT
L
4
POWER IN
5
CABLE
R
Not supplied
B
d/M
FUNC.
C
Not supplied
PORT. IN
Z
V
PORT. IN
1
<
+
- VOLUME +
- TREBLE +
MP3 player, etc...
AUX IN Connection
Connect an Output of auxiliary device to the AUX
(L/R) INPUT Connector.
AUX IN
AUX IN
CABLE
iPod
VIDEO OUT
iPod DOCK
R
Unit
ANTENNA
L
L
FM
R
SPEAKERS
L
4
POWER IN
5
Not supplied
CABLE
R
To the audio output
jacks of your component
(TV, VCR, etc.)
RedRed
White
White
,,Note
If your TV has only one output for audio
(mono), connect it to the left (white) audio jack
on the unit.
12
Connecting
USB Connection
Antenna Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Connect the FM antenna for listening to the radio.
1/!
B
d/M
Z
FUNC.
C
V
Connect the FM Wire antenna to the FM antenna
connector.
PORT. IN
2
Connecting
- BASS +
ANTENNA
<
VOLUME
FM
,,Note
yy Removing the USB Device from the unit
1. Choose a different function/ mode or
press Z ENTER twice in a row.
AUX IN
CABLE
iPod
VIDEO OUT
iPod DOCK
2. Remove the USB device from the unit
ANTENNA
L
R
FM
can only recharge your iPod through
yy You
USB port. To listen to music on iPod, refer to
the page 17.
SPEAKERS
L
4
POWER IN
5
CABLE
R
,,Note
After connecting, stretch the opposite side
of the cable to any direction where it is able
to receive incoming radio broadcast from
outside. There may be a various way of
stretching it.
3
Operating
Operating
Basic Operations
Other Operations
CD/ USB Operations
Programmed Playback
1. Insert the disc by pressing B (OPEN/CLOSE) or
connect the USB device to the USB port.
The program function enables you to store your
favorite files from any disc or USB device.
2. Select the CD or USB function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
A program can contain 20 tracks.
3. Select a file (or track) you want to play by
pressing C/V.
Do this
Press Z.
Press d/M.
Press d/M.
During playback, press C/V
Skipping to to go to the next track/ file or to
the next/ return to the beginning of the
previous current track/ file.
track/ file Press C twice briefly to step
back to the previous track/ file.
Searching Press and hold C/V during
for a section playback and release it at the point
within a track you want to listen to.
Searching
Press PRESET/FOLDER W/S and
for a section
then d/M.
within a folder
Press REPEAT/MENU on the
remote control repeatedly, the
Playing
display change in the following
repeatedly or order:
randomly OFF -> REPEAT TRK -> REPEAT DIR
(Only MP3/ WMA files) -> REPEAT
ALL -> RANDOM
1. Insert a CD or USB and wait for it to be order.
2. Press PROG./MEMO. on the remote control in
stop status.
3. Press C/V on the unit or on the remote
control in stop satus.
4. Press PROG./MEMO. again to save and select a
next track.
3
5. Press d/M to play the programmed music files.
Operating
To
Stop
Playback
Pause
13
6. To clear your selection, press Z ENTER,
PROG./MEMO. and then Z ENTER.
,,Note
The programs are also cleared when the disc
or USB device is removed, the unit is powered
off or the function is switched to others.
Displaying file information
(ID3 TAG)
While playing an MP3 file containing file
information, you can display the information by
pressing INFO..
Turn off the sound temporarily
Press @ MUTE to mute your unit.
You can mute your unit, for example, to answer the
telephone, the “MUTE” is displayed in the display
window.
14
Operating
Radio Operations
Be sure that FM aerial is connected.
(Refer to the page 12)
Listening to the radio
1. Press FUNCTION until FM appears in the display
window.
The last received station is tuned in.
2. Press and hold TUNING -/+ for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
3
Or
Operating
Press TUNING -/+ repeatedly.
3. Adjust the volume by rotating VOLUME +/on the unit or by pressing VOLUME +/- on the
remote control repeatedly.
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure to turn down the volume.
1. Press FUNCTION until FM appears in the display
window.
2. Select the desired frequency by pressing
TUNING -/+.
3. Press PROG./MEMO. a preset number will flash
in the display window.
4. Press PRESET/FOLDER W/S to select the
preset number you want.
5. Press PROG./MEMO. The station is stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press
PRESET/FOLDER W/S.
Deleting all the saved stations
1. Press and hold PROG./MEMO. for two seconds.
“ERASE ALL” will flash up on the unit display.
2. Press PROG./MEMO. to erase all saved radio
stations.
Improving poor FM reception
Press d/M on the unit or d/M on the remote
control. This will change the tuner from stereo to
mono and usually improve the reception.
Operating
Sound adjustment
15
Adjusting the sound
You can adjust the BASS and TREBLE by rotating
BASS or TREBLE.
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using EQ on the remote control.
The displayed items for the Equalizer may be
different depending on sound sources and regions.
Description
NATURAL
You can enjoy comfortable and
natural sound.
Local
Specialization
equalizer
Regionally optimized sound
effect. (FORRO/ FUNK/
SERTANEJO/ DANGDUT/
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/ SALSA/
SAMBA/ CUMBIA/ AFRO)
AUTO EQ
Realizes the sound equalizer that
is the most similar to the genre
of which is included in the MP3
ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock, pop,
jazz or classic concert.
MP3 -- OPT
This function is optimized
for compressible MP3 file. It
improves the treble sound.
BASS BLAST
Reinforces the treble, bass and
surround sound effect.
VIRTUAL
You can enjoy more virtual
surround sound.
BYPASS
You can enjoy the sound
without equalizer effect.
3
Operating
On Display
16
Operating
Setting the Clock
Using your player as an alarm
clock
1. Turn the unit on.
1. Turn the unit on.
2. Press CLOCK for at least 2 seconds.
2. Press TIMER. Each functions flashes.
3. Choose time mode by pressing C/V.
3. Press SET when the function you want to be
woken by is showing.
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4. Press SET to confirm your selection.
5. Select the hours by pressing C/V.
6. Press SET.
7. Select the minutes by pressing C/V.
3
8. Press SET.
4. “ON TIME” will be displayed. This is your desired
time to unit turns on. Press C/V to
change the hours and minutes and press SET to
save.
5. The “OFF TIME” will be displayed. This is your
desired time to unit turns off.
6. Press C/V to change the hours and
minutes and press SET to save.
Operating
7. Press C/V to change the volume and
press SET to save. The clock icon "(“ shows
that the alarm is set.
8. Press TIMER button 2 times. You can check the
setting status.
,,Note
yy If you set the clock time, you can check the
time by pressing CLOCK even when the
player is turned off.
yy If you set the clock time and alarm, you
can check the alarm icon “(“ by pressing
CLOCK even when the player is turned off.
yy If you set the clock time and alarm, you
can check the alarm icon “(“ and setting
informaiton by pressing TIMER even when
the unit is turned off. Then this function will
working in everyday.
Operating
Sleep Timer Setting
Press SLEEP repeatedly to select delay time
between 10 and 180 minutes. After the delay time,
unit will turn off.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
,,Note
yy You can check the remaining time before
the unit turns off.
17
Advanced Operations
Playing the iPod
You can enjoy the sound with your iPod. For details
about iPod, refer to the iPod User Guide.
1. Connect the iPod cradle.
2. Connect the iPod firmly.
AUX IN
CABLE
iPod
VIDEO OUT
yy Press SLEEP. The remaining time appears in
the display window.
iPod DOCK
;
ANTENNA
L
R
FM
yy Sleep function will be working after dimmer.
3
SPEAKERS
L
POWER IN
5
CABLE
R
Press SLEEP once. The display window will be
darkening by half. To cancel it, press SLEEP
repeatedly until dim off.
Operating
Dimmer
4
If you turn this unit on, your iPod is
automatically turned on and recharging starts.
3. Press FUNC. on the unit or FUNCTION on the
remote control to select iPod function. You can
operate your iPod through an iPod’s display
by using the supplied remote control and also
control on your iPod.
,,Note
yy With iPod cradle connected to iPod DOCK,
you can also connect VIDEO cable to iPod
VIDEO OUT (Refer to page 11).
yy You can control through both the TV and
iPod or iPhone in order to play music files,
and watch movie clips, and look at the
picutures which are saved to iPod or iPhone.
yy Depending on the iPod, make sure that
select Videos > Video settings, and then set
TV Out to Ask or On from your iPod.
For details about Video Settings, refer to the
iPod User Guide.
18
Operating
To
3
,,Note
Do this
ON UNIT
ON REMOTE
Pauses or
restart
d/M
d/M
Skip
C/V
C/V
Search
Press and hold
C/V
Press and hold
C/V
Move to the
previous
menu
-
REPEAT
/MENU
PRESET/
Operating
Move to the
desired item
-
FOLDER
W/S
Chooses a
item
Z
Z ENTER
Compatible iPod
e recommend installing the latest software
yy W
version.
yy T he unit supports the models as follows:
iPod nano 1 G, 2 G, 3 G, 4 G, 5 G, 6 G/
iPod classic/ iPod 5 G/
iPod touch 2 G, 3 G, 4 G/ iPhone 3 G, 3GS, 4.
For some models, the unit may not operate
depending on the firmware version.
epending on your iPod’s software version, you
yy D
may not control your iPod from the player.
yy If this unit displays an error message, follow
the message. An error message “ERROR”.
- Your iPod is not connected firmly.
-This unit recognizes your iPod as an unknown device.
- Your iPod is exceptionally low in power.
/ The battery needs to be charged.
/If you charge the battery while iPod
is extremely low in power, it may take
longer to be charged.
yy iPod does not support recording function
when connected.
epending on your iPod’s software version,
yy D
it may not be possible to control your iPod
from this unit. We recommend installing the
latest software version.
yy If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
iPod dock of this unit and then use it.
yy If you have a problem with your iPod, please
visit www.apple.com/support/ipod.
Listening to music from your
external device
The unit can be used to play the music from many
types of external device. (Refer to the page 11)
1. Connect the external device to the PORT. IN
connector of the unit.
Or
Connect the external device to the AUX IN
connector of the unit.
2. Turn the power on by pressing 1/! (POWER).
3. Select the PORTABLE function or AUX function
by pressing FUNC. on the unit or FUNCTION
on the remote control.
4. Turn the external device and start it playing.
Operating
Recording to USB
1. Connect the USB device to the unit.
2. Select a function by pressing FUNC. on the unit
or FUNCTION on the remote control.
,,Note
yy You can check the recording percentage
rate for the USB record on the display
window during the recording. (MP3/ WMA
CD Only)
One track recording - You can record to USB
after playing a file you want.
yy During recording MP3/ WMA, there is no
sound.
All tracks recording - You can record to USB after
stop.
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored. (AUDIO CD Only)
Program list recording - After showing the
programmed list, you can record it to USB.
3. Start the recording by pressing or X REC on
the remote control.
19
yy Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
yy If USB recording does not work, the
message like “NO USB”, “ERROR”, “FULL” or “NO
REC” is displayed on the display window.
Pausing recording
yy Multi card reader device or External HDD
can not be used for USB recording.
During recording, press X REC on the remote
control to pause recording. Press it again to restart
recording. (Only Radio/ Portable/ AUX)
To select recording bit rate
and speed
1. Press X REC on the remote control for longer
than 3 seconds.
2. Use C/V on the unit or remote control to
select the bit rate.
yy A file is recorded by about 512 Mbyte when
you record for a long term.
yy When you stop recording during playback,
the file will not be stored.
yy You may not store more than 999 files.
yy It’ll be stored as follows.
AUDIO CD
MP3/ WMA
The other
source*
3. Press X REC on the remote control again to
select the recording speed.
4. Press C/V on the unit or on the remote
control to select a desired recording speed;
(Only AUDIO CD)
X1 SPEED
- You can listen to music while recording it.
X2 SPEED
- You can just record the music file.
5. Press X REC on the remote control to finish the
setting.
* : TUNER, Portable and the like.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
3
Operating
4. To stop recording, press Z on the unit or
Z ENTER on the remote control.
4
Troubleshooting
20 Troubleshooting
Troubleshooting
General
Problem
Cause & Correction
yy The power cord is not plugged in. Plug in the power cord.
No Power.
No sound.
yy Check whether electricity failed. Check the condition by operating other
electronic devices.
yy Check whether you select right function. Press FUNCTION and check the
selected function.
yy If not, connect speaker cables correctly. Speaker cables connected
correctly.
yy An unplayable disc is inserted. Insert a playable disc.
4
The unit does not start
playback.
yy No disc is inserted. Insert a disc.
yy The disc is dirty. Clean the disc. (Refer to the 23 page)
Troubleshooting
yy The disc is inserted upside down. Place the disc with the label or printed
side facing upwards.
yy The antenna is positioned or connected poorly. Connect the antenna
securely.
Radio stations cannot
be tuned in properly.
yy The signal strength of the radio station is too weak. Tune to the station
manually.
yy No stations have been preset or preset stations have been cleared (when
tuning by scanning preset channels). Preset some radio stations, see page
14 for details.
yy The remote control is too far from the unit. Operate the remote control
within about 23 ft (7 m).
yy There is an obstacle in the path of the remote control and the unit. Remove
The remote control
the obstacle.
does not work properly.
yy The batteries in the remote control are exhausted. Replace the batteries
with new ones.
iPod does not work.
yy Check whether the player is connected to the unit correctly. Connect it to
the unit correctly.
5
Appendix
Appendix
21
Trademarks and
Licenses
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is a trademark of Apple Inc. “Made
for iPod” and “Made for iPhone” mean that
an electronic accessory has been designed
to connect specifically to iPod or iPhone
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory with
iPod, iPhone may affect wireless performance.
5
Appendix
22 Appendix
Specifications
General
Power requirements
110 - 240 V , 50/ 60 Hz
Power consumption
40 W
Dimensions (W x H x D)
240 X 136 X 240 mm
Net Weight (Approx.)
2.9 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Bus Power Supply
USB DC 5 V 0 500 mA
iPod DC 5 V 0 1 A
Inputs/ Outputs
PORT. IN
0.5 Vrms (3.5 mm stereo jack)
ANALOG AUDIO IN
iPod VIDEO OUT
0.6 Vrms (1 kHz), 600 Ω, RCA jack (L, R) x 1
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
Tuner
FM Tuning Range
5
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
Appendix
Stereo mode
50 W + 50 W
CD
Frequency Response
40 Hz to 20 kHz
Signal-to-noise ratio
75 dB
Dynamic range
more than 80 dB
Front Speaker
Type
2 Way 2 speaker
Impedance Rated
8Ω
Input Power
50 W
Max. Input Power
100 W
Net Dimensions (W x H x D)
160 X 266 X 206 mm
Net Weight
2.15 kg
yy Design and specifications are subject to change without notice.
Appendix 23
Maintenance
Handling the Unit
When shipping the unit
Notes on Discs
Handling Discs
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit.
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Maintaining the Unit
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising