LG | RN1329CD4P | LG RN1329CN7P Owner’s Manual

OWNER’S MANUAL
COMMERCIAL DRYER
Before beginning installation, read these instructions carefully.
this will simplify installation and ensure that the dryer is
installed correctly and safely. leave these instructions near the
dryer after installation for future reference.
MODEL
RN1329CD1P
RN1329CN1P
RN1329AD1P
RN1329AN1P
RN1329CD4P
RN1329CN4P
RN1329AD4P
RN1329AN4P
RN1329CD7P
RN1329CN7P
RN1329AD7P
RN1329AN7P
www.lg.com
MFL67863717
Copyright © 2017 LG Electronics Inc. All Rights Reserved.
2
PRODUCT FEATURES
PRODUCT FEATURES
OUTSTANDING PERFORMANCE
The dryer features the largest capacity, quick drying times, quiet operation, and an energy-saving system.
ARTISTIC DESIGN
Modern front panel look and big clear glass door make your dryer look stylish
EASY OF USE
An entire selection of user-friendly functions makes operating the dryer easy.
ULTRA CAPACITY
The larger drum enables better tumbling and less tangling and wrinkling of the laundry.
IMPORTANT SAFETY INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Warning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, Injury to persons, or death.
Your Safety and the safety of others is very important.
e have provided many important safety messages in this manual and on your appliance.
W
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.
These words mean:
DANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
Warning
You can be killed or seriously injured if you don’t follow instructions.
CAUTION
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are not followed.
BASIC SAFETY PRECAUTIONS
Warning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
• Read all instructions before using the dryer.
• Keep area around the exhaust opening and adjacent surrounding
• Before use, the dryer must be properly installed as described in this
areas free from the accumulation of lint, dust, and dirt.
manual.
• The interior of the dryer and exhaust vent should be cleaned
• Do not place items exposed to cooking oils in your dryer. Items
periodically by qualified service personnel.
contaminated with cooking oils may contribute to a chemical
• Do not install or store the dryer where it will be exposed to the
reaction that could cause a load to catch fire.
weather.
• Do not dry articles that have been previously cleaned in, washed in,
• Always check the inside of the dryer for foreign objects.
soaked in, or spotted with gasoline, dry-cleaning solvents, or other
• Clean lint screen before or after each load.
flammable or explosive substances as they give off vapors that could
• Do not dry unwashed items in the tumble dryer.
ignite or explode.
• Items that have been soiled with substances such as cooking oil,
• Do not reach into the dryer if the drum or any other part is moving.
acetone, alcohol,petrol,kerosene,spot removers, turpentine, waxes
• Do not repair or replace any part of the dryer or attempt any servicing
and wax removers should be washed in hot water with an extra
unless specifically recommended in this Use and Care Guide or in
amount of detergent before being dried in the tumble dryer.
published user-repair instructions that you understand and have the
• Items such as foam rubber(latex foam), shower caps, waterproof
skills to carry out.
textiles, rubber backed articles and clothes or pillows fitted with foam
• Do not tamper with controls.
rubber pads should not be dried in the tumble dryer.
• Before the dryer is removed from service or discarded, remove the
• Fabric softeners, or similar products, should be used as specified by
door to the drying compartment.
the fabric softener instructions.
• Do not allow children to play on or in the dryer. Close supervision of
• The final part of a tumble dryer cycle occurs without heat(cool down
children is necessary when the dryer is used near children.
cycle) to ensure that the items are left at a temperature that ensures
• Do not use fabric softeners or products to eliminate static unless
that the items will not be damaged.
recommended by the manufacturer of the fabric softener or product.
• If the supply cord is damaged, it must be replaced by the
• Do not use heat to dry articles containing foam rubber or similarly
manufacturer, its service agent or similarly qualified persons in order
textured rubber-like materials.
to avoid a hazard.
Warning
Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
• The lint trap has to be cleaned frequently, if applicable.
• This appliance is not to be used by children or persons with
• Lint must not to be allowed to accumulate around the tumble
reduced physical, sensory or mental capabilities, or lack of
dryer.
experience and knowledge, unless they have been given
• Adequate ventilation has to be provided to avoid the back flow
supervision or instruction.
of gases into the room from appliances burring other fuels,
• Children should be supervised not to play with the appliance.
including open fires.
• The tumble dryer is not to be used if industrial chemicals have
been used for cleaning
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
■ What is not covered.
Service trips to your home to instruct you on the product.
If the product is connected to any voltage other than that shown on the rating plate.
If the fault is caused by accidents, neglects, misuses of Acts of God.
If the fault is caused by reasons except for normal domestic use or use in accordance with the owner’s manual.
If the fault is caused by pests, for example, rats or cockroaches etc..
Noise or vibration that is considered normal,for example, water drain sound, spin sound or warning beeps.
Correcting the installation for example, leveling the product, adjustment of drain.
Normal maintenance recommended by the owner’s manual.
Removal of foreign objects/substances from the machine including the pump and inlet hose filter, for example,
grit,nails, bra wires and buttons etc..
Replace fuses in or correct wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects with this appliance.
If this product is used for commercial purposes, it is not warranted.
(Example:Public places such as public bathroom, lodging house, training center, dormitory)
If the product is installed outside the normal service area, any cost of transportation involved in the repair of the
products, or the replacement of a defective part, shall be borne by the owner.
READ ALL INSTRUCTIONS BEFORE USE
Warning
The appliance must not be supplied through an external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by a utility
Warning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, Injury to persons, or death.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this appliance
or any other appliances.
• Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
WHAT TO DO IF YOU SMELL GAS: (Applicable for Gas models)
1. D
o not try to light a match or cigarette, or turn on
any gas or electrical appliance.
2. D
o not touch any electrical switches. Do not use
any phone in your building.
3. Clear the room, building, or area of all occupants.
4. Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions carefully.
5. If you cannot reach your gas supplier, call the fire
department.
IMPORTANT SAFETY INSTRUCTIONS
5
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Warning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event
of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a
path of least resistance for electric current. This
appliance must be equipped with a cord having an
equipmentgrounding conductor and a grounding
plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not use an adapter or extension cord. Do not
remove ground prong. If you don’t have the proper
outlet, consult an electrician.
Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This appliance must be connected to a
grounded metal, permanent wiring system or
an equipmentgrounding conductor must be run
with the circuit conductors and connected to the
equipmentgrounding terminal or lead on the
appliance.
Electric shock can result if the dryer is not properly
grounded.
Warning
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with
a qualified electrician or service person if you are in doubt as to whether the appliance is properly grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
Warning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Properly ground dryer to conform with all governing
• Place dryer at least 18 in. above the floor for a
codes and ordinances. Follow details in the
garage installation. Failure to do so can result in death,
installation instructions. Electric shock can result if
explosion, fire, or burns.
the dryer is not properly grounded.
• Keep all packaging from children. Packaging
• Before use, the dryer must be properly installed as
material can be dangerous for children. There is a risk
described in this manual. Electric shock can result if
of suffocation.
the dryer is not properly grounded.
• Keep the area underneath and around your
• Install and store the dryer where it will not be
appliances free of combustible materials such as
exposed to temperatures below freezing or exposed
lint, paper, rags, chemicals, etc. Failure to do so can
to the weather.
result in fire.
• All repairs and servicing must be performed
• Do not place candles, smoking materials, or other
by an authorized servicer unless specifically
flammables on to top of the product. Dripping wax,
recommended in this Owner’s Guide. Use only
smoke, or fire can result.
authorized factory parts. Failure to follow this warning
• Remove all protective vinyl film from the product.
can cause serious injury, fire, electric shock, or death.
Failure to do so can cause product damage, smoke or
• To reduce the risk of electric shock, do not install the
fire.
dryer in humid spaces. Failure to follow this warning
• This appliance must be installed by an authorised
can cause serious injury, fire, electric shock, or death.
person in accordance with this instruction manual,
• Connect to a properly rated, protected, and sized
AS/NZS 5601 – Gas installations (installation and pipe
power circuit to avoid electrical overload. Improper
sizing), local gas fitting regulations, local electrical
power circuit can melt, creating electric shock and/or
regulations, local water regulations, local health
fire hazard.
regulations, Building Code of Australia and any other
government authority.
• The appliance must not be supplied through an external
switching device, such as a timer, or connected to a
• On completion of installation, installer to test operation
circuit that is regularly switched on and off by a utility.
of appliance and instruct the user on the correct
operation before leaving.
• Remove all packing items and dispose of all shipping
materials properly. Failure to do so can result in death,
• All adjustments to this appliance must be carried out by
explosion, fire, or burns.
authorized personnel.
• If appliance does not appear to be operating correctly
contact LG Electronics or an authorized service person.
6
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Warning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR INSTALLATION
Exhaust/Ducting:
•G
as dryers MUST be exhausted to the outside.
Failure to follow these instructions can result in fire or
death.
•T
he dryer exhaust system must be exhausted to the
outside of the dwelling. If the dryer is not exhausted
outdoors, some fine lint and large amounts of
moisture will be expelled into the laundry area. An
accumulation of lint in any area of the home can create
a health and fire hazard.
•U
se only rigid metal or flexible metal 4-in. diameter
ductwork inside the dryer cabinet or for exhausting
to the outside. Use of plastic or other combustible
ductwork can cause a fire. Punctured ductwork
can cause a fire if it collapses or becomes otherwise
restricted in use or during installation.
•D
uctwork is not provided with the dryer, and you
should obtain the necessary ductwork locally. The
end cap should have hinged dampers to prevent
backdraft when the dryer is not in use. Failure to
follow these instructions can result in fire or death.
• The appliance must not be installed behind a lockable
door, a sliding door or a door with a hinge on the
opposite side to that of the tumble dryer, in such a
way that a full opening of the tumble dryer door is
restricted.
• The openings must not be obstructed by a carpet.
• E xhaust air must not be discharged into a flue which
Is used for exhausting fumes from appliances burning
gas or other fuels.
•T
he exhaust duct must be 4 in. (10 cm) in diameter
with no obstructions. The exhaust duct should be
kept as short as possible. Make sure to clean any
old ducts before installing your new dryer. Failure to
follow these instructions can result in fire or death.
• Rigid or semi rigid metal ducting is recommended
for use between the dryer and the wall. In special
installations when it is impossible to make a
connection with the above recommendations, a ULlisted flexible metal transition duct may be used
between the dryer and wall connection only. The
use of this ducting will affect drying time. Failure to
follow these instructions can result in fire or death.
• DO NOT use sheet metal screws or other fasteners
which extend into the duct that could catch lint and
reduce the efficiency of the exhaust system. Secure
all joints with duct tape. For complete details,
follow the Installation Instructions. Failure to follow
these instructions can result in fire or death.
• Oil-affected items can ignite spontaneously, especially
when exposed to heat sources Such as in a tumble
dryer. The items become warm, causing an oxidation
reaction in the oil. Oxidation creates heat. If the heat
cannot escape, the items can become hot enough to
catch fire. Piling, stacking or storing oil-affected items
can prevent heat from escaping and so create a fire
hazard.
• If it is unavoidable that fabrics that contain vegetable
or cooking oil or have been contaminated by hair care
products be placed in a tumble dryer they should first
be washed in hot water with extra detergent-this will
reduce, but not eliminate, the hazard. Washed in hot
water with extra detergent-this will reduce, but not
eliminate, the hazard.
• DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR
THIS APPLIANCE.
• DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.
• DO NOT MODIFY THIS APPLIANCE.
• THIS APPLIANCE SHALL NOT BE USED TO DRY OFF
SOLVENTS OR DRYCLEANING FLUIDS.
WARNING - To avoid a fire
Do not wash clothes or items that have any contaminants of flammable solvents or substances. Do
not clean the product or expose it to flammable substances.
IMPORTANT SAFETY INSTRUCTIONS
7
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Warning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
Warning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•D
o not, under any circumstances, cut or remove
the ground prong from the power cord. To prevent
injury to persons or damage to the dryer, the electrical
power cord must be plugged into a properly grounded
outlet.
•F
or personal safety, this dryer must be properly
grounded. Failure to do so can result in electric shock
or injury.
•R
efer to the installation instructions in this manual
for specific electrical requirements for your model.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•T
his dryer must be plugged into a properly
grounded outlet. Electric shock can result if the
dryer is not properly grounded. Have the wall
outlet and circuit checked by a qualified electrician
to make sure the outlet is properly grounded.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
• Never unplug your dryer by pulling on the power
cord. Always grip plug firmly and pull straight out
from the outlet. The power cord can be damaged,
resulting in a risk of fire and electric shock.
• Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end. The power cord can
melt, creating electric shock and/or fire hazard.
• When installing or moving the dryer, be careful not
to pinch, crush, or damage the power cord. This will
prevent injury and prevent damage to the dryer from
fire and electric shock.
• To reduce the risk of injury to persons, adhere
to all industry recommended safety procedures
including the use of long sleeved gloves and safety
glasses. Failure to follow all of the safety warnings in
this manual could result in property damage, injury to
persons or death.
•T
he dryer should always be plugged into its own
individual electrical outlet which has a voltage
rating that matches the rating plate. This provides
the best performance and also prevents overloading
house wiring circuits which could cause a fire hazard
from overheated wires.
CAUTIION
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied
through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off
by the utility
NOTE
The appliance is provided with a standard 3 pin plug and is suitable for any standard Australian GPO outlet
SAVE THESE INSTRUCTIONS
8
CONTENTS
CONTENTS
2
PRODUCT FEATURES
3
IMPORTANT SAFETY
INSTRUCTIONS
3
5
5
7
BASIC SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS
SAFETY INSTRUCTIONS FOR INSTALLATION
SAFETY INSTRUCTIONS FOR CONNECTING
ELECTRICITY
9SPECIFICATIONS
29
30
31
32
33
34
35
36
37
8. Regular priced dryer cycle time
9. Special priced dryer cycle time
10. Value of coin 1
11. Value of coin 2 (Set up for top off price and
e-suds coin pulse)
12. Penny increment pricing offset
13. Top off time
14. Beep volume
15. Time to keep the coin (Use only for coin
type)
16. How to enter the tyPE
38 PROGRAMMING MODE
- Test Mode
13 OPERATING YOUR DRYER
39
40
41
42
43
14 PROGRAMMING MODE
44 PROGRAMMING MODE
- Collect Mode
15 PROGRAMMING MODE
- COIN/CARD
46MAINTENANCE
16 PROGRAMMING MODE - OPL
47 STACK MACHINE INSTALLATION
INSTRUCTIONS
17 PROGRAMMING MODE
- Setup Mode
49 ERROR MODE
10IDENTIFICATION
17 1. How to change regular price.
18 2. How to change special price
19 3. H
ow to enter the FEA1
20 3-1. Special price day setup
21 3-2. Vend type setup - card type or coin
type setup
22 3-3. Top off apply or not setup
23 4. How to enter the FEA2
24 4-1. Pause function setup
25 5. How to enter the special price day setup
26 5-1. How to change sunday
27 6. Special price beginning time setup
28 7. Special price ending time setup
1. LqC1
2. Factory reset - EEPt
3. Time Set Up
4. Courtesy cycle
5. Cycle Kill
49 POWER FAIL RECOVERY
49 DEFAULT DRYER SETTINGS
SPECIFICATIONS
SPECIFICATIONS
■ Information about the model
RN1329CD1P
Combination
control
Card/OPL
RN1329CD4P
Card/OPL
Single
Card/OPL
Upper
Coin
Lower
Model
RN1329CD7P
RN1329CN1P
Exterior
color
Stainless
Silver
Installation
Lower
RN1329CN4P
Coin
Single
RN1329CN7P
Coin
Upper
RN1329AD1P
Card/OPL
Lower
RN1329AD4P
Card/OPL
Single
Card/OPL
Upper
RN1329AD7P
RN1329AN1P
White
Coin
Lower
RN1329AN4P
Coin
Single
RN1329AN7P
Coin
Upper
AGA 8657-G
Gas Type: Natural Gas
Universal LPG
TPP Pressure: 0.75kPa
1.75kPa
Injector size: 2.27mm
1.47mm
Total MJ/h: 22.5
22.5
■ Type : Gas Dryer
: 220-240V~, 50Hz
■ Rating
Electricity
consumption
: 320W/2.35A (MAX 700W/3.52A)
■
: 686mm(W) x 764mm(D) x 983mm(H)
■ Single dryer size
: 686mm(W) x 764mm(D) x 1954mm(H)
■ Stack dryer size : 10Kg
■Capacity : 59.4 kg
■ Weight ■ Specifications are subject to change by manufacturer.
NOTE
Specifications subject to change by manufacturer.
9
10
IDENTIFICATION
IDENTIFICATION
■ OPL TYPE
- Side by side (RN1329CD4P, RN1329AD4P)
- Stack upper (RN1329CD7P, RN1329AD7P)
- Stack Lower (RN1329CD1P, RN1329AD1P)
4
1
2
3
1. DISPLAY LED
3. START BUTTON
2. CYCLE BUTTON
4. STATUS LED
IDENTIFICATION
Control panel features
3
3
■ Coin type
- Side by side (RN1329CN4P, RN1329AN4P)
3
4
4
1
1
2
2
4
1
2
3
3
3
- Stack upper (RN1329CN7P, RN1329AN7P)
4
4
1
1
2
2
4
1
2
3
3
4
1
2
4
1
2
3
- Stack4Lower (RN1329CN1P,
RN1329AN1P)
1
2
3
3
3
11
12
IDENTIFICATION
Status LED
3
Display LED
Cycle button
Start/Pause button
Display LED
The Display shows the vend price, remaining time, and
programming options.
Error codes are also displayed here.
Cycle button
Press the cycle button to Select the desired cycle based
on laundry types and conditions.
High Temp.
Use this cycle to get high heat for heavy fabrics, such
as jeans corduroys or work clothes (High heat).
Med Temp.
Use for drying sturdy fabrics such as work casual
clothes (Medium heat).
Low Temp.
Use for drying synthetic fabrics,washable knit fabrics
and noiron finishes (Low heat).
No Heat
Use for items that require heat-free drying such as
plastics or rubber.
Start/Pause button
The Start LED flashes when the full vend price has been
satisfied then the cycle has been chosen or the machine
is paused.
The Start LED flashes when a card is inserted to add time
to the current cycle.
If you press the Start/Pause button while dryer is
working, machine will be paused.
STATUS LED
LED
Description
LED flashes when the duct is blocked by
lint.
Check and clean the duct.
LED flashes whenever the heating cycle
is in operation.
LED flashes whenever the cool down
cycle is in operation.
OPERATING YOUR DRYER
13
OPERATING YOUR DRYER
1. Ready mode
1) Coin / Card type
- The cycle LEDs flash at the same time, when the
price of cycles are equal.
2) OPL type
- The cycle LEDs is lit at the same time, and displayed
‘PUSH’.
2. Insert card/coin (not for OPL type)
■ Insert a cash card that has a sufficient balance.
The card balance should be more than the
programmed vend price for a selected cycle.
NOTE
When the card balance is not enough, machine
displays the balance for 5 seconds and then displays
message repetitively
■ Insert a sufficient amount of change that is a more
than the programmed vend price for a selected cycle.
NOTE
When the coin amount is not enough, the machine
will not start.
3. Select the cycle
Press the desired cycle and the start button. The display
LED will show the remaining time and the selected cycle
starts.
NOTE
The last 2 minutes of the remaining time are always
for the cool down portion.
4. Top off (To add more time)
■ After a debit card is inserted, the operating time can
be increased to 15 minutes/$1.00 (default), when the
Start button or the chosen course button has been
pressed.
(The card should have enough balance to satisfy
increasing time.)
■ The operating time can be increased to 15
minutes/$1.00 (default) by adding more coins.
NOTE
Owner can control the additional time and money
setting (top off price).
When the COOL DOWN has been working, if time is
added, it goes back to the DRYING.
Time can be added up 99 minutes.
5. Change cycle
■ You cannot change the cycle while the machine is
running.
■ But if the door is opened, the machine stops
temporarily and the cycle can be changed.
6. Cycle finish
■ After the COOL DOWN of cycle, the machine stops
and LED display shows End.
If you press any key or open the door, the dryer
defaults to the ready mode.
14
PROGRAMMING MODE
PROGRAMMING MODE
1. Programming mode
You can check machine information or change setting on Program setup or Diagnostic test.
There are two methods that you can enter programming mode.
■ How to enter “Programming mode”
You can enter programming mode only for Idle state
and pause state.
■ How to use button
You can change Dryer vend price, cycle time and Cycle
parameters, etc.
- Card Type
Press button
Description
High Temp.
Move to upper level
Med Temp.
Move to the mode in the
same level (+)
Low Temp.
Move to the modes in the
same level (-)
No Heat
-
Start
Enter the selected mode
1) Insert service card.
2) Display will show
- Coin Type
1) Dissemble upper coin box key.
2) Take out the coin drop from the coin box.
3) Turn on/off the toggle switch at the back of the coin
box.
4) Display will show “
”.
- OPL Type
1) Push the High Temp. and Low Temp. button at the
same time.
2) Push the Med Temp. button 3 times.
3) Push the Srart button.
4) Display will show “
”
Coin Box Key
Coin Vault
COIN TYPE
Insert debit card
CARD TYPE
OPL TYPE
NOTE
• If you turn on the power without connecting the meter case for the first time, the machine will display
• When the machine comes from the factory, it is set in the coin type. You can change Card/Coin type by button.
.)
(For more information refer to SETUP mode’s
• The machine will display “PUSH” for OPL type
.
PROGRAMMING MODE
Card / Coin type
Algorithm Flow Chart shows how to control programming mode.
Before program set, check the structure of programming mode.
1. Turn on/off toggle switch or Insert the service card to entering set up mode.
2. Press High Temp. button to move the upper level.
3. Press Med Temp.(+) or Low Temp.(-) button if you want to be at the same level.
4. Press Start button to enter the details of Set up, Diagnostic Tests mode.
is to set price value, time value and vend type etc.
consists of line test, reset, free cycle and kill cycle.
Is to collect the usage data.
Structure of Programming mode
NOTE
• Do not use
,
.
• It is only used in inspecting the machine.
15
16
PROGRAMMING MODE
OPL type
Algorithm Flow Chart shows how to control programming mode.
Before program set, check the structure of programming mode.
1) Push the High Temp. and Low Temp. button at the same time.
2) Push the Med Temp. button 3 times.
3) Push the Start button.
4) Display will show “
“
is to set price value, time value and vend type etc.
consists of line test, reset, free cycle and kill cycle.
Is to collect the usage data.
Structure of Programming mode
NOTE
• Do not use
,
.
• It is only used in inspecting the machine.
PROGRAMMING MODE
PROGRAMMING MODE - Setup Mode
Setup Mode :
(display)
You can change dryer vend price, cycle time, and cycle parameters, etc.
Entering set up mode
• Coin type - Turn on/off toggle switch.
• Card type - Insert the service card.
• Stack type - Take off control panel, and turn on/off toggle switch.
• OPL/Coin Type – Push “High Temp.” + “Low Temp.” and then enter password “3”.
• Then, dryer displays
.
1. How to change regular price.
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Start button.
Display previous regular price.
Press Med Temp.(+) or Low Temp.(-) button to set regular price.
(The vend price can be set from 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the regular price, then advances to the
next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
• rgCP(regular delicate price) is not available in dryer.
• rgrP(regular warm/cold price) is not available in dryer.
• rgHP (regular hot price) is not available in dryer.
Display
17
18
PROGRAMMING MODE
2. How to change special price
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special price.
Press Med Temp.(+) or Low Temp.(-) button to set special price.
(The vend price can be set from 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the special price, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High temp.” twice.
NOTE
• SPCP(special delicate price) is not available in dryer.
• SPrP(special warm/cold price) is not available in dryer.
• SPHP (special hot price) is not available in dryer.
• SCPA(add super cycle price) is not available in dryer.
• SPCt(add super wash type) is not available in dryer.
Display
PROGRAMMING MODE
3. How to enter the
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Structure of
Content of
• Special price days apply or not
• Disabled
• Add super wash apply or not
• Select vend type
• This function is not available
• Pre-wash apply or not
• Top off apply or not (only for dryer)
• Twin spray apply or not
• Disable
• Enable
19
20
PROGRAMMING MODE
3-1. Special price day setup
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Start button.
Press Med Temp. or Low Temp. button and then select
or
.
Disable
Enable
Press the Start button.
The machine sets up the special price day, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
• noSt (Non-stop wash apply or not) is not available in dryer.
• SUUE (add super wash apply or not) is not available in dryer.
One or the other will
display.
PROGRAMMING MODE
21
3-2. Vend type setup - card type or coin type setup
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press Med Temp. or Low Temp. button and then select
or
.
Coin type
Card type
Press the Start button.
The machine sets up the vend type, then go to the idle mode
automatically.
NOTE
• SEdE (sensor dry apply or not) is not available in dryer.
• PrSH (Pre-wash apply or not) is not available in dryer.
• After setting the Value to VEND, vend type is changed directly without power on/off.
One or the other will
display.
22
PROGRAMMING MODE
3-3. Top off apply or not setup
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press Med Temp. or Low Temp. button and then select
or
.
Disable
Enable
Press the Start button.
The machine sets up top off function, then advances to the next
process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
• tEIn (Twin spray apply or not) is not available in dryer.
One or the other will
display.
PROGRAMMING MODE
4. How to enter the
Enter setup mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Structure of
Content of
• Pause function apply or not
23
24
PROGRAMMING MODE
4-1. Pause function setup
Enter setup mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Start button.
Press Med Temp. or Low Temp. button and then select
or
.
Disable
Enable
Press the Start button.
The machine sets up the pause function, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” three times.
One or the other will
display.
PROGRAMMING MODE
5. How to enter the special price day setup
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Structure of
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Display
25
26
PROGRAMMING MODE
5-1. How to change sunday
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Start button.
Press Med Temp.(+) or Low Temp. button and then select
or
.
Disable
Enable
Press the Start button.
The machine sets up the special price day (Sunday), then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
As explained on the previous page, other days can be set up by the same method.
One or the other will
display.
PROGRAMMING MODE
6. Special price beginning time setup
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special price beginning time.
Press Med Temp.(+) or Low Temp.(-) button to select time between 0 and 23.
Press the Start button.
The machine sets up the special price beginning time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
Display
27
28
PROGRAMMING MODE
7. Special price ending time setup
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special price ending time.
Press Med Temp.(+) or Low Temp.(-) button to select time between 1 and 24.
Press the Start button.
The machine sets up the special price ending time, then advances
to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
When setting up a special price period, the ending time must be later than the beginning time.
Display
PROGRAMMING MODE
8. Regular priced dryer cycle time
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous regular priced dryer cycle time.
Press Med Temp.(+) or Low Temp.(-) button to select time between 5 and 99.
Press the Start button.
The machine sets up the regular priced dryer cycle time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
Display
29
30
PROGRAMMING MODE
9. Special priced dryer cycle time
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special priced dryer cycle time.
Press Med Temp.(+) or Low Temp.(-) button to select time between 5 and 99.
Press the Start button.
The machine sets up the special priced dryer cycle time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
• CCCC (washing time) is not available in dryer.
• nrPC (rinsing times per cycle) is not available in dryer.
• rt (rinsing time setup) is not available in dryer.
• tSSd (top spin speed) is not available in dryer.
Display
PROGRAMMING MODE
10. Value of coin 1
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous coin 1 value.
Press Med Temp.(+) or Low Temp.(-) button to select value of
coin 1 (The value can be set from 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the value of coin 1, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
Display
31
32
PROGRAMMING MODE
11. Value of coin 2 (Set up for top off price and e-suds coin pulse)
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous coin 2 value.
Press Med Temp.(+) or Low Temp.(-) button to select value of
coin 2 (The value can be set from 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the value of coin 2, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
• Coin type : Value of coin 2 is same function as setting for the e-Suds coin pulse.
• Card type : Value of coin 2 is same function as the top off price.
(As changing the value of coin 2, you can change the top off price and e-Suds coin pulse.)
PROGRAMMING MODE
12. P
enny increment pricing offset
This represents the cent increment price offset used when debit card is setup.
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous penny increment pricing offset.
Press Med Temp.(+) or Low Temp.(-) button to select value of
PIPo. (0~4)
Press the Start button.
The machine sets up the PIPo, then advances to the next process
automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
•P
ence increment pricing offset is available only in card type.
(It hasn’t affected on the coin type’s price setting.)
Display
33
34
PROGRAMMING MODE
13. Top off time
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous top off time.
Press Med Temp.(+) or Low Temp.(-) button to select time between 1 and 30.
Press the Start button.
The machine sets up the top off time, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
• UULE(water level) is not available in dryer.
Display
PROGRAMMING MODE
14. Beep volume
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous value.
Press Med Temp.(+) or Low Temp.(-) button to select High or
Low or Off.
Press the Start button.
The machine sets up the beep volume, then advances to the next
process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
Display
35
36
PROGRAMMING MODE
15. Time to keep the coin (Use only for coin type)
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous value.
Press Med Temp.(+) or Low Temp.(-) button to select time between 0 ~ 180.
Press the Start button.
The machine sets up the time to keep the coin, then advances to
the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
NOTE
• dHUE(drop count) is not available in dryer.
• rSEn(rinse spin enable) is not available in dryer.
Display
PROGRAMMING MODE
37
16. How to enter the
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Structure of
Content of
• Product type
• Currency choice
0 EUK (England)
1 EAP (Australia)
• Card reader type
• Coin drop type
2 ELC (USA)
3 EPN (China)
4 KOR (Korea)
5 EJP (Japan)
6 ECI (Canada)
7 GSC (Philippines)
0 (Pharos)
1 (HP)
0 (Greenwald)
1 (Heartland, ESD)
0 (ESD, Greenwald, Munzprufer) - Signal Pulse : 50ms
1 (Korea) - Signal Pulse : 100ms
NOTE
• Pay means card or coin type.
•D
efault type is coin type. If you want to change coin type to card type, you need to setup vend type in fea1. (refer
to FEA1 function)
• Free means OPL type.
• CUSt (Custom program) is not available in dryer.
• Price setting varies by country.
38
PROGRAMMING MODE
PROGRAMMING MODE - Test Mode
Diagnostic tests :
(display)
This program has been added for testing the dryer and detecting errors.
Entering the test mode
Machine
Data
Name
1. Entering
programming
mode
CARD /
COIN
2. High Temp.
Entering
the test
mode
OPL
Button
Display
Description
Insert service card (Card type), Turn on/off toggle switch
(Coin type).
Press the High Temp. button.
Then
appears in the display.
3. Start
Enter the diagnostic test mode.
1. Entering
programming
mode.
Push and hold the High Temp. and Low Temp. at the same time.
After that push Med Temp. button for 3 times. Push Start button.
2. High Temp.
3. Start
Press the High Temp. button.
Then
appears in the display.
Enter the diagnostic test mode.
PROGRAMMING MODE
39
1. Pressing the Start button cycles to the next test function.
Number of times
the Start
button is pressed
Checking point
None
Display
LqC 1
1 time
Check the version and code of machine.
Gas Coin type : P1:Og
Gas Card type : P1:Cg
Gas OPL type : P1:Pg
Version and code of machine (All LED on)
Display 88:88 and P1:XX and gU:XX and gd:XX alternately.
XX is product type or the version number.
2 time
PDA CHECK
Ir--
3 time
Motor runs.
Measured moisture value (70~239)
GAS TYPE: Motor runs.
4 time
5 time
6 time
7 time
GAS TYPE: GAS valve runs.
Motor+Valve
LED & KEY CHECK
Press High Temp. button.
Press Med Temp. button.
Press Low Temp. button.
Press No Heat button.
Test ends.
Door switch
During check, if the
(Motor & Heater Off, Buzzer beeps
door is open.
seven times)
During check, if the Test goes back at step 3.
door is closed
(Motor on & Heater Off )
NOTE
Do not use
.
Current temperature (5~70)
(Displays the temperature inside the drum in ° Celsius.)
Current temperature (5~70)
(Displays the temperature inside the drum in ° Celsius.)
Version and code of machine
LqC1
dE
(The door is open. Please close the door completely)
Measured moisture value (70~239)
40
PROGRAMMING MODE
2. F
actory reset - EEPt
After a factory reset, all values are reset to the default values.
Entering set up
mode.
You will see LqC1
Button
Display
Press the Med Temp. or the Low Temp. Button until
appears in the display.
Press the Start button.
Press the Med Temp. button until
display.
appears in the
Press the Start button, then factory reset is done.
NOTE
•D
ryer default value for CARD/COIN machine
- Drying time 45 Minute
- Top off time 15 Minute
• Drying time in OPL machine can be changed from 1 to 100 Minutes by pressing the cycle button.
PROGRAMMING MODE
3. Time Set Up
Entering set up
mode.
You will see LqC1
Button
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
The display cycles through 2000 --> 0101 --> Sat --> 0000.
Press the Start button.
Press Med Temp. (+) or Low Temp.(-) button to select year
between 2000 and 2099.
Press the Start button.
The machine sets up the year, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select month
between 01 and 12.
Press the Start button.
The machine sets up the month, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select day
between 01 and 31.
Press the Start button.
The machine sets up the day, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select hour
between 00 and 23.
Press the Start button.
The machine sets up the hour, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select minute
between 00 and 59.
Press the Start button.
The machine sets up the minute.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type – Press “High Temp.” twice.
Display
41
42
PROGRAMMING MODE
4. C
ourtesy cycle
Courtesy cycle is like a complimentary cycle given to the customer when the dryer goes out of order when
the customer has made the payment to dry one’s clothes.
Entering set up
mode.
You will see LqC1
Button
Display
Press the Med Temp. or the Low Temp. Button until
appears in the display.
Press the Start button.
Press the Med Temp. button until
display.
Press the Start button.
Display will show
or
appears in the
.
Coin type
Card type
Select the course you desire.
NOTE
• In case of dryer card type, it has to insert the cash card after
removing the service card. Then press the cycle course and
the start button. (It is only applicable to the dryer’s card type
specially and there is no subtraction in card balance at the
Courtesy cycle.)
Press the Start button.
Display will show the remaining time and start.
PROGRAMMING MODE
5. C
ycle Kill
Coin type
Entering set up
mode.
You will see LqC1
Button
Display
Press the Med Temp. or the Low Temp. Button until
appears in the display.
Press the Start button.
Press the Med Temp. button until
display.
appears in the
Press the Start button.
Display
with beeping.
Go back to ready mode.
Card type
Insert
cycle kill card.
Descriptions
Display the current time and
Display
with beeping.
Go back to ready mode.
NOTE
OPL type
- Dryer machine will end the cycle by opening the door.
.
Display
43
44
PROGRAMMING MODE
PROGRAMMING MODE - Collect Mode
Collect Information Data : CLCt (display)
The dryer collects the usage data so that the owner can check various information like number of various cycles
used, how many times card or coins used, etc.
Entering the collect mode
Data Name
Entering
the collect
mode
Step (Button)
LED Display
Description
1. Entering the
programming mode.
Insert service card(Card type), Turn on/off toggle switch
(Coin type).
2. High Temp.
Press the High Temp. button until “tESt” appears in the
display.
3. M
ed Temp.(+) or Low
Temp.(-)
Press the Med Temp. or Low Temp. button until “CLCt”
appears in the display.
4. Start
Enter the Collect information data.
5. M
ed Temp.(+) or Low
Temp.(-)
Move to each data list that you want to check by pressing
with Med Temp. or Low Temp. button.
6. Start
Display the value of selected data list
7. High Temp.
Move to upper level or Comes back to Idle State
Check the collect information reference to the follow lists. The Lists are displayed by abbreviations.
Collect Mode Data lists
No.
Abbreviation
1
rgPr
Meaning
2
rgCP
Regular Cold Price
rgCP is not available in dryer. (It can’t enter.)
3
rgrP
Regular Warm Price
rgrP is not available in dryer. (It can’t enter.)
Regular Price
Description
$0.00 ~ $10.00
4
rgHP
Regular Hot Price
rgHP is not available in dryer. (It can’t enter.)
5
dELC
Dryer Moisture Sense
dELC is not available in dryer. (It can’t enter.)
6
ItrC
Interval Regular Cycles
Number of Regular cycles (0 ~ 65535)
7
ItCC
Interval Regular Cold Cycles
ItCC is not available in dryer. (It can’t enter.)
8
ItAC
Interval Regular Warm Cycles
ItAC is not available in dryer. (It can’t enter.)
9
ItHC
Interval Regular Hot Cycles
ItHC is not available in dryer. (It can’t enter.)
10
ItSC
Interval Super Cycles
ItSC is not available in dryer. (It can’t enter.)
11
IttF
Interval Topoff Cycles (Dryer Only)
Number of Topoff cycles (0 ~ 65535)
12
ItUC
Interval Service Cycles
Number of Service cycles (0 ~ 65535)
13
ItFC
Interval Token Cycles
Number of Token cycles (0 ~ 65535)
14
ACrC
Accumulated Regular Cycles
Number of Regular cycles (0 ~ 65535)
15
ACCC
Accumulated Regular Cold Cycles
ACCC is not available in dryer. (It can’t enter.)
16
ACAC
Accumulated Regular Warm Cycles
ACAC is not available in dryer. (It can’t enter.)
17
ACHC
Accumulated Regular Hot Cycles
ACHC is not available in dryer. (It can’t enter.)
18
ACSC
Accumulated Super Cycles (Washer Only)
ACSC is not available in dryer. (It can’t enter.)
19
ACtF
Accumulated Topoff Cycles (Dryer Only)
Number of Topoff cycles (0 ~ 65535)
20
ACUC
Accumulated Service Cycles
Number of Service cycles (0 ~ 65535)
21
ACFC
Accumulated Token Cycles
Number of Token cycles (0 ~ 65535)
22
ACrt
Accumulated Run Time
Number of Running minutes (0 ~ 65535)
PROGRAMMING MODE
45
Collect Mode Data lists
No.
Abbreviation
Meaning
Description
23
Itnr
Interval No Runs
Itnr is not available in dryer.
24
Ittb
Interval Trouble Cycles
Ittb is not available in dryer.
25
ItPd
Interval Power Downs
Number of power down
26
Itdd
Interval Unauthorized Service Door
Openings
Number of Unauthorized Service Door Openings
( 0~ 255)
27
ItAd
Interval Authorized Service Door
Openings
Number of Unauthorized Service Door Openings
( 0~ 255)
28
ItUC
Interval Unauthorized Coin Vault Openings
Number of Authorized Service Door Openings
( 0~ 255)
29
ItAC
Interval Authorized Coin Vault Openings
Number of Authorized Service Door Openings
( 0~ 255)
30
Ittl
Interval Total Income
Amount of money for Total Income
( 0 ~ 65535)
31
ACtl
Accumulated Total Income
Amount of money for Total Income
( 0 ~ 65535)
32
IttC
Interval Total Cycles
Number of Total cycles ( 0~65535 )
33
ACtC
Accumulated Total Cycles
Number of Total cycles ( 0~65535 )
34
SCPr
Super Cycle Price
Scpr is not available in dryer. (It can’t enter.)
35
toPr
Top Off Price
$0.00 ~ $10.00
36
Itd
Interval Money
Amount of money for regular cycle
( 0 ~ 65535)
37
ACd
Accumulated Money
Amount of money for regular cycle
( 0 ~ 65535)
38
Ittd
Interval Topoff Money
Amount of money for Topoff( 0 ~ 65535)
39
ACtd
Accumulated Topoff Money
Amount of money for Topoff( 0 ~ 65535)
INTERVAL means collecting since last data collection.
ACCUMULATED means collecting over a period of time since last factory reset (EEPt).
Authorized: Turning on/off the toggle switch with PDA Communication.
(Turning on/off the toggle switch within 30 minutes after Communicating with PDA)
Unauthorized: Turning on/off the toggle switch without PDA Communication.
46
MAINTENANCE
MAINTENANCE
■ Regular cleaning
Warning
Cleaning the Lint Filter
Always clean the lint filter after every cycle.
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
• Unplug the dryer before cleaning to avoid the risk
of electric shock. Failure to follow this warning can
cause serious injury, fire, electric shock, or death.
• Never use harsh chemicals, abrasive cleaners, or
solvents to clean the washer. They will damage the
finish.
Cleaning the Exterior
Proper care of your dryer can extend its life.
The outside of the machine can be cleaned with warm
water and a mild, nonabrasive household detergent.
Immediately wipe off any spills with a soft, damp cloth.
NOTE
Do not use methylated spirits, solvents, or similar
products.
Never use steel wool or abrasive cleansers; they can
damage the surface.
Lint Filter
To clean, open the dryer door and pull the lint filter
straight up.Then:
1. Roll any lint off the filter with your fingers, or
Cleaning the Interior
Wipe around the door opening and seal with a soft,
damp cloth to prevent lint and dust buildup that could
damage the door seal.
Clean the window with a soft cloth dampened with
warm water and a mild, nonabrasive household
detergent; then wipe dry.
The stainless steel drum can be cleaned with a
conventional stainless steel cleaner, used according to
the manufacturer’s specifications.
Never use steel wool or abrasive cleansers; they can
scratch or damage the surface.
2. Vacuum the lint filter, or
Cleaning Around and Under the Dryer
Vacuum lint and dust from around the dryer and
underneath it regularly. Vent ductwork should be
checked for lint buildup and cleaned at least once per
year. If any noticeable reduction in airflow or drying
performance occurs, immediately check ductwork for
obstructions and blockages.
3. If the lint filter has become very dirty or clogged with
fabric softener, wash the lint filter in warm, soapy
water and allow to dry thoroughly before reinstalling.
Maintaining Ductwork
Vent ductwork should be checked for lint buildup
and cleaned at least once per year. If any noticeable
reduction in airflow or drying performance occurs,
immediately check ductwork for obstructions and
blockages. Contact a qualified technician or service
provider.
NOTE
NEVER operate the dryer without the lint filter in
place. NEVER operate the dryer with a wet lint filter.
STACK MACHINE INSTALLATION INSTRUCTIONS
47
STACK MACHINE INSTALLATION INSTRUCTIONS
1. SUITABLE MODEL FOR STACKING
Stack type
Model Name
Upper Dryer
RN1329CD7P
RN1329AD7P
RN1329CN7P
RN1329AN7P
Lower Dryer
RN1329CD1P
RN1329AD1P
RN1329CN1P
RN1329AN1P
Lower Washer
FH069FD6P / F1069FD6F
FH069FDP / F1069FDF
2. S
TACKING KIT
- STACKING KIT is provided in the upper dryer.
- STACKING KIT includes the stacking bracket(1), security bracket(3), bolt(1), screw(9).
1) Stacking bracket
2) bolt
3) Screw
4) security bracket
- SLIDING KIT includes the slide bracket(2), sliding pad(4), screw(18).
1) Stacking bracket
2) Sliding pad
NOTE
- The machine can be stacked only on the model designated as suitable by LGE.
- Do not stack the washer on the top.
- You can order the parts for stacking from Qualified dealer or Qualified SVS agent of LGE.
3) Screw
48
STACK MACHINE INSTALLATION INSTRUCTIONS
3. S
tacking the machine
- Install two sliding brackets on the top plate of lower washer.
- Remove the legs from the leg brackets.
- Remove the four(4) leg brackets from the bottom of upper dryer.
- Assemble the four(4) slide pads on the base.
*Security bracket installation (Only coin model)
- Install two security bracket on the panel frame and top plate in the lower
washer.
- Install one security bracket on the lower panel frame in the upper dryer.
- Lift and stack the upper dryer on the lower washer.
- Set the rear of the upper dryer and the rear of the lower washer in the same position.
- Push the upper dryer matching the slide & stacking bracket to make upper and lower front parallel.
- Install the stacking bracket at the rear of the stacked dryer and washer.
- Assemble the six(6) screw to fix the lower machine and upper dryer.
NOTE
Please refer to Service Manual for detail to explain how to stack and fix the machine
ERROR MODE / POWER FAIL RECOVERY / DEFAULT DRYER SETTINGS
49
ERROR MODE
■M
eaning of Error Codes that LED displays during occurrence or
problem.
Dryer error code
PROBLEM
POSSIBLE CAUSE
SOLUTION
It is displayed when thermistor is opened or
shorted
Thermistor should be replaced.
It is displayed when thermistor temperature
have increased about 17 degrees for 10 seconds
Thermistor should be replaced.
Disconnection of card reader wire.
Check the card reader wire.
It is displayed when the gas supply is poor or
has been shut off.
Check the gas supply.
POWER FAIL RECOVERY
In case of power failure the machine stops running but the time display remains on, showing the time just before
power failure.
Press the Start button after the power is restored, then the machine will restart.
DEFAULT DRYER SETTINGS
Default Settings
Default
Cycle Time (Minutes)
45 Minutes
Cool Down Cycle Time
2 Minutes
High Temperature
154.4° F (68° C)
Medium Temperature
140° F (60° C)
Low Temperature
125.6° F (52.5° C)
Top Off Time (Minutes per coin)
15 Minutes
Coin #1 Value
$1.00
Coin #2 Value
$1.00
Minutes/Minutes and seconds
Minutes
Fahrenheit/Celsius
Fahrenheit
Error Mode
On
50
51
Download PDF