LG | RV1329A7S | LG RV1329A7S Owner’s Manual

OWNER'S MANUAL
COMMERCIAL DRYER
Please read this manual carefully before operating
your dryer and retain it for future reference.
MODEL
RN1329AD1 / RV1329AD1
RN1329AD5 / RV1329AD5
RN1329AD6 / RV1329AD6
RN1329AD5S / RV1329AD5S
P/NO. : MFL62512853
RN1329AN4 / RV1329AN4
RN1329AN7 / RV1329AN7
RN1329AN1 / RV1329AN1
RN1329AN7S / RV1329AN7S
RN1329A4 / RV1329A4
RN1329A7 / RV1329A7
RN1329A1 / RV1329A1
RN1329A7S / RV1329A7S
PRODUCT FEATURES
OUTSTANDING PERFORMANCE
The dryer features the largest capacity, quick drying times, quiet operation, and an
energy-saving system.
ARTISTIC DESIGN
Modern front panel look and big clear glass door make your dryer look stylish
EASY OF USE
An entire selection of user-friendly functions makes operating the dryer easy.
ULTRA CAPACITY
The larger drum enables better tumbling and less tangling and wrinkling of the laundry.
CONTENTS
PART 1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................................. 3
PART 2. SPECIFCATIONS .................................................................................................................................... 8
PART 3. IDENTIFICATION ..................................................................................................................................... 9
PART 4. OPERATING YOUR DRYER ................................................................................................................. 12
PART 5. PROGRAMMING MODE ....................................................................................................................... 13
PART 6. MAINTENANCE ..................................................................................................................................... 41
PART 7. STACK MACHINE INSTALLATION INSTRUCTIONS .......................................................................... 42
PART 8. ERROR MODE ...................................................................................................................................... 45
PART 9. POWER FAIL RECOVERY ................................................................................................................... 45
PART 10. DEFAULT DRYER SETTINGS ............................................................................................................ 45
2
Part 1
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING For your safety, the information in this manual must be followed to minimize the risk of
fire or explosion, electric shock, or to prevent property damage, Injury to persons, or death.
Your Safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey
all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.
These words mean:
DANGER: You will be killed or seriously injured if you don’t immediately follow instructions.
WARNING: You can be killed or seriously injured if you don’t follow instructions.
CAUTION: You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are not followed.
BASIC SAFETY PRECAUTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance,
•
•
•
•
•
•
•
•
•
•
•
follow basic precautions, including the following:
Read all instructions before using the dryer.
• Keep area around the exhaust opening and adjacent surrounding areas
free from the accumulation of lint, dust, and dirt.
Before use, the dryer must be properly installed as described in this
• The interior of the dryer and exhaust vent should be cleaned periodically
manual.
by qualified service personnel.
Do not place items exposed to cooking oils in your dryer. Items
• Do not install or store the dryer where it will be exposed to the weather.
contaminated with cooking oils may contribute to a chemical reaction that
could cause a load to catch fire.
• Always check the inside of the dryer for foreign objects.
Do not dry articles that have been previously cleaned in, washed in,
• Clean lint screen before or after each load.
soaked in, or spotted with gasoline, dry-cleaning solvents, or other
• Do not dry unwashed items in the tumble dryer.
flammable or explosive substances as they give off vapors that could
• Items that have been soiled with substances such as cooking oil,
ignite or explode.
acetone, alcohol,petrol,kerosene,spot removers, turpentine, waxes and
Do not reach into the dryer if the drum or any other part is moving.
wax removers should be washed in hot water with an extra amount of
Do not repair or replace any part of the dryer or attempt any servicing
detergent before being dried in the tumble dryer.
unless specifically recommended in this Use and Care Guide or in
• Items such as foam rubber(latex foam), shower caps, waterproof textiles,
published user-repair instructions that you understand and have the skills
rubber backed articles and clothes or pillows fitted with foam rubber pads
to carry out.
should not be dried in the tumble dryer.
Do not tamper with controls.
• Fabric softeners, or similar products, should be used as specified by the
Before the dryer is removed from service or discarded, remove the door
fabric softener instructions.
to the drying compartment.
• The final part of a tumble dryer cycle occurs without heat(cool down
Do not allow children to play on or in the dryer. Close supervision of
cycle) to ensure that the items are left at a temperature that ensures that
children is necessary when the dryer is used near children.
the items will not be damaged.
Do not use fabric softeners or products to eliminate static unless
• If the supply cord is damaged, it must be replaced by the manufacturer,
recommended by the manufacturer of the fabric softener or product.
its service agent or similarly qualified persons in order to avoid a hazard.
Do not use heat to dry articles containing foam rubber or similarly textured
rubber-like materials.
WARNING:
Never stop a tumble dryer before the end of the drying cycle unless all items are
quickly removed and spread out so that the heat is dissipated.
• The lint trap has to be cleaned frequently, if applicable.
• Lint must not to be allowed to accumulate around the tumble dryer.
• Adequate ventilation has to be provided to avoid the back flow of gases
into the room from appliances burring other fuels, including open fires.
• This appliance is not to be used by children or persons with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
• Children should be supervised not to play with the appliance.
3
Part 1
IMPORTANT SAFETY INSTRUCTIONS
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
What is not covered.
Service trips to your home to instruct you on the product.
If the product is connected to any voltage other than that shown on the rating plate.
If the fault is caused by accidents, neglects, misuses of Acts of God.
If the fault is caused by reasons except for normal domestic use or use in accordance with the owner's
manual.
If the fault is caused by pests, for example, rats or cockroaches etc..
Noise or vibration that is considered normal,for example, water drain sound, spin sound or warning beeps.
Correcting the installation for example, leveling the product, adjustment of drain.
Normal maintenance recommended by the owner's manual.
Removal of foreign objects/substances from the machine including the pump and inlet hose filter, for
example, grit,nails, bra wires and buttons etc..
Replace fuses in or correct wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects with this appliance.
If this product is used for commercial purposes, it is not warranted.
(Example:Public places such as public bathroom, lodging house, training center, dormitory)
If the product is installed outside the normal service area, any cost of transportation involved in the repair of
the products, or the replacement of a defective part, shall be borne by the owner.
READ ALL INSTRUCTIONS BEFORE USE
WARNING For your safety, the information in this manual must be followed to minimize the risk of
fire or explosion, electric shock, or to prevent property damage, Injury to persons, or death.
• Do not store or use gasoline or other flammable
• Installation and service must be performed by a
vapors and liquids in the vicinity of this appliance or
qualified installer, service agency, or the gas
any other appliances.
supplier.
WHAT TO DO IF YOU SMELL GAS: (Applicable for Gas models)
1. Do not try to light a match or cigarette, or turn on
any gas or electrical appliance.
2. Do not touch any electrical switches. Do not use
any phone in your building.
3. Clear the room, building, or area of all occupants.
4
4. Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions carefully.
5. If you cannot reach your gas supplier, call the fire
department.
Part 1
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. This appliance must
be equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug
must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with
all local codes and ordinances.
Do not use an adapter or extension cord. Do not
remove ground prong. If you don’t have the proper
outlet, consult an electrician.
Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This appliance must be connected to a grounded
metal, permanent wiring system or an equipmentgrounding conductor must be run with the circuit
conductors and connected to the equipmentgrounding terminal or lead on the appliance.
Electric shock can result if the dryer is not properly
grounded.
WARNING — Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service person if you are in doubt as to whether
the appliance is properly grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this
appliance, follow basic precautions, including the following:
• Remove all packing items and dispose of all
• Properly ground dryer to conform with all
shipping materials properly. Failure to do so can
governing codes and ordinances. Follow details
result in death, explosion, fire, or burns.
in the installation instructions. Electric shock can
result if the dryer is not properly grounded.
• Place dryer at least 18 in. above the floor for a
garage installation. Failure to do so can result in
• Before use, the dryer must be properly installed
death, explosion, fire, or burns.
as described in this manual.
Electric shock can result if the dryer is not properly
• Keep all packaging from children. Packaging
grounded.
material can be dangerous for children. There is
a risk of suffocation.
• Install and store the dryer where it will not be
exposed to temperatures below freezing or
• Keep the area underneath and around your
exposed to the weather.
appliances free of combustible materials such
as lint, paper, rags, chemicals, etc. Failure to do
• All repairs and servicing must be performed by
so can result in fire.
an authorized servicer unless specifically
recommended in this Owner’s Guide. Use only
• Do not place candles, smoking materials, or
authorized factory parts. Failure to follow this
other flammables on to top of the product.
warning can cause serious injury, fire, electric
Dripping wax, smoke, or fire can result.
shock, or death.
• Remove all protective vinyl film from the
• To reduce the risk of electric shock, do not
product. Failure to do so can cause product
install the dryer in humid spaces. Failure to
damage, smoke or fire.
follow this warning can cause serious injury, fire,
electric shock, or death.
• Connect to a properly rated, protected, and
sized power circuit to avoid electrical overload.
Improper power circuit can melt, creating electric
shock and/or fire hazard.
5
Part 1
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR INSTALLATION
Exhaust/Ducting:
• Gas dryers MUST be exhausted to the outside.
Failure to follow these instructions can result in fire
or death.
• The dryer exhaust system must be exhausted
to the outside of the dwelling. If the dryer is
not exhausted outdoors, some fine lint and
large amounts of moisture will be expelled into
the laundry area. An accumulation of lint in any
area of the home can create a health and fire
hazard.
• Use only rigid metal or flexible metal 4-in.
diameter ductwork inside the dryer cabinet or
for exhausting to the outside. Use of plastic or
other combustible ductwork can cause a fire.
Punctured ductwork can cause a fire if it collapses
or becomes otherwise restricted in use or during
installation.
• Ductwork is not provided with the dryer, and
you should obtain the necessary ductwork
locally. The end cap should have hinged
dampers to prevent backdraft when the dryer
is not in use. Failure to follow these instructions
can result in fire or death.
• The openings must not be obstructed by a carpet.
• Exhaust air must not be discharged into a flue
which Is used for exhausting fumes from
appliances burning gas or other fuels.
6
• The exhaust duct must be 4 in. (10 cm) in
diameter with no obstructions. The exhaust
duct should be kept as short as possible. Make
sure to clean any old ducts before installing
your new dryer. Failure to follow these
instructions can result in fire or death.
• Rigid or semi rigid metal ducting is
recommended for use between the dryer and
the wall. In special installations when it is
impossible to make a connection with the
above recommendations, a UL-listed flexible
metal transition duct may be used between the
dryer and wall connection only. The use of this
ducting will affect drying time. Failure to follow
these instructions can result in fire or death.
• DO NOT use sheet metal screws or other
fasteners which extend into the duct that could
catch lint and reduce the efficiency of the
exhaust system. Secure all joints with duct
tape. For complete details, follow the
Installation Instructions. Failure to follow these
instructions can result in fire or death.
Part 1
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using this
appliance, follow basic precautions, including the following:
• Do not, under any circumstances, cut or
remove the ground prong from the power cord.
To prevent injury to persons or damage to the
dryer, the electrical power cord must be plugged
into a properly grounded outlet.
• For personal safety, this dryer must be
properly grounded. Failure to do so can result in
electric shock or injury.
• Refer to the installation instructions in this
manual for specific electrical requirements for
your model. Failure to follow these instructions
can create an electric shock hazard and/or a fire
hazard.
• This dryer must be plugged into a properly
grounded outlet. Electric shock can result if
the dryer is not properly grounded. Have the
wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded. Failure to follow these instructions can
create an electric shock hazard and/or a fire
hazard.
• The dryer should always be plugged into its
own individual electrical outlet which has a
voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
• Never unplug your dryer by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet. The power cord can
be damaged, resulting in a risk of fire and electric
shock.
• Repair or replace immediately all power cords
that have become frayed or otherwise
damaged. Do not use a cord that shows cracks
or abrasion damage along its length or at
either end. The power cord can melt, creating
electric shock and/or fire hazard.
• When installing or moving the dryer, be careful
not to pinch, crush, or damage the power cord.
This will prevent injury and prevent damage to the
dryer from fire and electric shock.
• To reduce the risk of injury to persons, adhere
to all industry recommended safety
procedures including the use of long sleeved
gloves and safety glasses. Failure to follow all of
the safety warnings in this manual could result in
property damage, injury to persons or death.
SAVE THESE INSTRUCTIONS
7
Part 2
SPECIFICATIONS
■ Type : Electric and Gas Dryer
■ Rating : Please refer to the rating label regarding detailed information.
■ Single dryer size : 686mm(W) x 764mm(D) x 983mm(H)
■ Stack dryer size : 686mm(W) x 764mm(D) x 1954mm(H)
■ Capacity : 10Kg
■ Weight : 59.4 kg
❋ Specifications are subject to change by manufacturer.
Note
Specifications subject to change by manufacturer.
8
Part 3
IDENTIFICATION
■ CARD TYPE
- SIDE BY SIDE(RN1329AD1, RV1329AD1)
- STACK UPPER(RN1329AD5, RV1329AD5, RN1329AD5S, RV1329AD5S )
- STACK LOWER(RN1329AD6, RV1329AD6)
4
1
2
3
■ OPL TYPE
- SIDE BY SIDE(RN1329A4, RV1329A4)
- STACK UPPER(RN1329A7, RV1329A7, RN1329A7S, RV1329A7S )
- STACK LOWER(RN1329A1, RV1329A1)
4
1
2
3
1. DISPLAY LED
2. CYCLE BUTTON
3. START BUTTON
4. STATUS LED
9
Part 3
IDENTIFICATION
■ COIN TYPE
- SIDE BY SIDE(RN1329AN4, RV1329AN4)
4
1
2
3
■ COIN TYPE
- STACK UPPER(RN1329AN7, RV1329AN7, RN1329AN7S, RV1329AN7S)
4
1
2
3
■ COIN TYPE
- STACK LOWER(RN1329AN1, RV1329AN1)
4
1
2
3
1. DISPLAY LED
2. CYCLE BUTTON
10
3. START BUTTON
4. STATUS LED
Part 3
IDENTIFICATION
STATUS LED
DISPLAY LED
4
CYCLE BUTTON
1
2
3
START BUTTON
1 DISPLAY LED
The Display shows the vend price, remaining time,
and programming options.
Error codes are also displayed here.
3 START BUTTON
The START LED flashes when the full vend price
has been satisfied then the cycle has been chosen or
the machine is paused.
The START LED flashes when a card is inserted to
add time to the current cycle.
4 STATUS LED
2 CYCLE BUTTON
Press the cycle button to Select the desired cycle
based on laundry types and conditions.
•
•
LED flashes whenever the heating
cycle is in operation.
LED flashes whenever the cool down
cycle is in operation.
WHITES & COLORS
Use this cycle to get high heat for heavy fabrics,
such as jeans corduroys or work clothes (High heat).
PERM. PRESS
Use for drying sturdy fabrics such as work casual
clothes (Medium heat).
DELICATES
Use for drying synthetic fabrics,washable knit
fabrics and no-iron finishes (Low heat).
NO HEAT
Use for items that require
heat-free drying such as plastics or rubber.
11
Part 4
OPERATING YOUR DRYER
1 Ready mode
1) Coin / Card type
- The cycle LEDs flash at the same time, when the
price of cycles are equal.
2) OPL type
- The cycle LEDs is lit at the same time, and displayed
‘PUSH’.
2 Insert card/coin (not for OPL type)
Insert a cash card that has a sufficient balance.
The card balance should be more than the
programmed vend price for a selected cycle.
Note
When the card balance is not enough, machine
displays the balance for 5 seconds and then
displays
message repetitively
Insert a sufficient amount of change that is a more
than the programmed vend price for a selected
cycle.
Note
When the coin amount is not enough, the
machine will not start.
3 Select the cycle
Press the desired cycle and the start button. The
display LED will show the remaining time and the
selected cycle starts.
Note
The last 2 minutes of the remaining time are
always for the cool down portion.
12
4 Top off (To add more time)
After a debit card is inserted, the operating
time can be increased to 15 minutes/$1.00
(default), when the START button or the
chosen course button has been pressed.
(The card should have enough balance to
satisfy increasing time.)
The operating time can be increased to 15
minutes/$1.00 (default) by adding more
coins.
Note
Owner can control the additional time and
money setting (top off price).
When the COOL DOWN has been working, if
time is added, it goes back to the DRYING.
Time can be added up 99 minutes.
5 Change cycle
You cannot change the cycle while the machine is
running.
But if the door is opened, the machine stops
temporarily and the cycle can be changed.
6 Cycle finish
After the COOL DOWN of cycle, the machine
stops and LED display shows End.
If you press any key or open the door, the dryer
defaults to the ready mode.
Part 5
PROGRAMMING MODE
1 Programming mode
You can check machine information or change setting on Program setup or Diagnostic test.
There are two methods that you can enter programming mode.
How to enter "Programming mode"
You can enter programming mode
only for Idle state and pause state.
How to use button
You can change Dryer vend price, cycle time and
Cycle parameters, etc.
- Card Type
1) Insert service card.
2) Display will show
- Coin Type
1) Dissemble upper coin box key.
2) Take out the coin drop from the coin box.
3) Turn on/off the toggle switch at the back of the
coin box.
4) Display will show “
”.
- OPL Type
1) Push the WHITES & DELICATES and
DELICATES button at the same time.
2) Push the PERM.PRESS button 3 times.
3) Push the START button.
4) Display will show “
”
Press button
Description
WHITES &
COLORS
Move to upper level
PERM.
PRESS
Move to the mode in the
same level (+)
DELICATES
Move to the modes in the
same level (-)
NO HEAT
-
START
Enter the selected mode
Coin Box Key
Coin Vault
COIN TYPE
Insert debit card
CARD TYPE
OPL TYPE
Note
• If you turn on the power without connecting the meter case for the first time, the machine will display
.
• When the machine comes from the factory, it is set in the coin type. You can change Card/Coin type by button.
(For more information refer to SETUP mode’s
.)
• The machine will display “PUSH” for OPL type
• Do not enter the "Vend type set up" mode if the machine is a coin type. You cannot restore it back to Coin type
without a special card reader and a service card after it has been changed to Card type in the set up mode.
13
Part 5
PROGRAMMING MODE - COIN/CARD
Algorithm Flow Chart shows how to control programming mode.
Before program set, check the structure of programming mode.
1. Turn on/off toggle switch or Insert the service card to entering set up mode.
2. Press WHITES & COLORS button to move the upper level.
3. Press PERM. PRESS(+) or DELICATES(-) button if you want to be at the same level.
4. Press START button to enter the details of Set up, Diagnostic Tests mode.
is to set price value, time value and vend type etc.
consists of line test, reset, free cycle and kill cycle.
Is to collect the usage data.
STRUCTURE OF PROGRAMMING MODE
Note
• Do not use
,
.
• It is only used in inspecting the machine.
14
Part 5
PROGRAMMING MODE - OPL
Algorithm Flow Chart shows how to control programming mode.
Before program set, check the structure of programming mode.
OPL Type
1) Push the WHITES & COLOURS and DELICATES button at the same time.
2) Push the PERM.PRESS button 3 times.
3) Push the START button.
4) Display will show “
”
is to set price value, time value and vend type etc.
consists of line test, reset, free cycle and kill cycle.
Is to collect the usage data.
STRUCTURE OF PROGRAMMING MODE
Note
• Do not use
,
.
• It is only used in inspecting the machine.
15
Part 5
PROGRAMMING MODE - Setup Mode
Setup Mode :
(display)
You can change dryer vend price, cycle time, and cycle parameters, etc.
Entering set up mode
• Coin type - Turn on/off toggle switch.
• Card type - Insert the service card.
• Stack type - Take off control panel, and turn on/off toggle switch.
• OPL type – Push “WHITES&COLORS” + “DELICATES” and the ‘3’.
• Then, dryer displays
.
1 How to change regular price.
Button
Entering set up mode.
You will see LqC1
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the START button.
Display previous regular price.
Press PERM. PRESS(+) or DELICATES(-) button to set
regular price.
(The vend price can be set from 0 to 10.00 in 1$ increments.)
Press the START button.
The machine sets up the regular price, then advances to the
next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
• rgCP (regular cold price) is not available in dryer.
• rgrP (regular warm price) is not available in dryer.
• rgHP (regular hot price) is not available in dryer.
16
Display
Part 5
PROGRAMMING MODE - Setup Mode
2 How to change special price
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous special price.
Press PERM. PRESS(+) or DELICATES(-) button to set
special price.
(The vend price can be set from 0 to 10.00 in 1$ increments.)
Press the START button.
The machine sets up the regular price, then advances to the
next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
• SPCP (special cold price) is not available in dryer.
• SPrP (special warm price) is not available in dryer.
• SPHP (special hot price) is not available in dryer.
• SCPA (add super cycle price) is not available in dryer.
• SPCt (add super wash type) is not available in dryer.
17
Part 5
PROGRAMMING MODE - Setup Mode
3 How to enter the
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Structure of
Content of
• Special price days apply or not
• Disabled
• Add super wash apply or not
• Select vend type
• This function is not available
• Pre-wash apply or not
• Top off apply or not (only for dryer)
• Disable
• Enable
18
Part 5
PROGRAMMING MODE - Setup Mode
3-1 Special price day setup
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display
.
Press the START button.
Press PERM. PRESS or DELICATES button and then
select
or
.
One or the other will
display.
Disable
Enable
Press the START button.
The machine sets up the special price, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
• CLEE (clear escrow enable or not) is not available in dryer.
• SUUE (add super wash apply or not) is not available in dryer.
19
Part 5
PROGRAMMING MODE - Setup Mode
3-2 Vend type setup - card type or coin type setup
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display
.
Press the PERM. PRESS or the DELICATES button until
appears in the display.
Press the START button.
Press PERM. PRESS or DELICATES button and then select
or
.
Coin type
Card type
Press the START button.
The machine sets up the vend type, then go to the idle mode
automatically.
Note
• SEdE (sensor dry apply or not) is not available in dryer.
• PrSH (Pre-wash apply or not) is not available in dryer.
20
One or the other will
display.
Part 5
PROGRAMMING MODE - Setup Mode
3-3 Top off apply or not setup
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display
.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press PERM. PRESS or DELICATES button and then
select
or
.
One or the other will
display.
Disable
Enable
Press the START button.
The machine sets up the Vend type, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
21
Part 5
PROGRAMMING MODE - Setup Mode
4 How to enter the special price day setup
Button
Entering set up mode.
You will see LqC1
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display
.
Structure of
22
Display
Part 5
PROGRAMMING MODE - Setup Mode
4-1 How to change sunday
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display
.
Press the START button.
Press PERM. PRESS(+) or DELICATES button and then
select
or
.
One or the other will
display.
Disable
Enable
Press the START button.
The machine sets up the special price day (Sunday), then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
As explained on the previous page, other days can be set up by the same method.
23
Part 5
PROGRAMMING MODE - Setup Mode
5 Special price beginning time setup
Button
Entering set up mode.
You will see LqC1
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous special price beginning time.
Press PERM. PRESS(+) or DELICATES(-) button to
select time between 0 and 23.
Press the START button.
The machine sets up the special price beginning time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
24
Display
Part 5
PROGRAMMING MODE - Setup Mode
6 Special price ending time setup
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous special price ending time.
Press PERM. PRESS(+) or DELICATES(-) button to select
time between 1 and 24.
Press the START button.
The machine sets up the special price ending time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
When setting up a special price period, the ending time must be later than the beginning time.
25
Part 5
PROGRAMMING MODE - Setup Mode
7 Regular priced dryer cycle time
Button
Entering set up mode.
You will see LqC1
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous regular priced dryer cycle time.
Press PERM. PRESS(+) or DELICATES(-) button to select
time between 10 and 99.
Press the START button.
The machine sets up the regular priced dryer cycle time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
26
Display
Part 5
PROGRAMMING MODE - Setup Mode
8 Special priced dryer cycle time
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous special priced dryer cycle time.
Press PERM. PRESS(+) or DELICATES(-) button to select
time between 10 and 99.
Press the START button.
The machine sets up the special priced dryer cycle time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
• CCCC (washing time) is not available in dryer.
• nrPC (rinsing times per cycle) is not available in dryer.
• rt (rinsing time setup) is not available in dryer.
• tSSd (top spin speed) is not available in dryer.
27
Part 5
PROGRAMMING MODE - Setup Mode
9 Value of coin 1
Button
Entering set up mode.
You will see LqC1
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous coin 1 value.
Press PERM. PRESS(+) or DELICATES(-) button to select
value of coin 1 (The value can be set fronm 0 to 10.00 in 1$
increments.)
Press the START button.
The machine sets up the value of coin 1, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
28
Display
Part 5
PROGRAMMING MODE - Setup Mode
10 Value of coin 2 (Set up for top off price and e-suds coin pulse)
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous coin 2 value.
Press PERM. PRESS(+) or DELICATES(-) button to select
value of coin 2 (The value can be set fronm 0 to 10.00 in 1$
increments.)
Press the START button.
The machine sets up the value of coin 2, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
• Coin type : Value of coin 2 is same function as setting for the e-Suds coin pulse.
• Card type : Value of coin 2 is same function as the top off price.
(As changing the value of coin 2, you can change the top off price and e-Suds coin pulse.)
29
Part 5
PROGRAMMING MODE - Setup Mode
11 Penny increment pricing offset
This represents the cent increment price offset used when debit card is setup.
Button
Entering set up mode.
You will see LqC1
Press the WHITES & COLORS button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous penny increment pricing offset.
Press PERM. PRESS(+) or DELICATES(-) button to select
value of PIPo. (0~4)
Press the START button.
The machine sets up the PIPo, then advances to the next
process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
Note
• Penny increment pricing offset is available only in card type.
(It hasn’t affected on the coin type’s price setting.)
30
Display
Part 5
PROGRAMMING MODE - Setup Mode
12 Top off time
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous top off time.
Press PERM. PRESS(+) or DELICATES(-) button to select
time between 1 and 30.
Press the START button.
The machine sets up the top off time, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
31
Part 5
PROGRAMMING MODE - Setup Mode
13 Beep volume
Button
Entering set up mode.
You will see LqC1
Press the WHITES & COLORS button
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous value.
Press PERM. PRESS(+) or DELICATES(-) button to select
High or Low or Off.
Press the START button.
The machine sets up the beep volume, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL type - Push “WHITES&COLORS” + “DELICATES”
and the ‘3’.
32
Display
Part 5
PROGRAMMING MODE - Setup Mode
14 Time to keep the coin (Use only for coin type)
Button
Entering set up mode.
You will see LqC1
Display
Press the WHITES & COLORS button
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Press the PERM. PRESS or the DELICATES
button until
appears in the display.
Press the START button.
Display previous value.
Press PERM.PRESS(+) or DELICATES(-) button to select
time between 1 ~ 180 or ‘Disable’.
Press the START button.
The machine sets up the time to keep the coin, then advances
to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
33
Part 5
PROGRAMMING MODE - Test Mode
Diagnostic tests :
(display)
This program has been added for testing the dryer and detecting errors.
Entering the test mode
Machine
Data Name
Button
Display
1. Entering programming mode
CARD
/COIN
2. WHITES & COLORS
3. START
Entering
the test mode
1. Entering programming mode.
OPL
2. WHITES & COLORS
3. START
Description
Insert service card (card type), Turn on/off toggle switch (Coin type).
Press the WHITES & COLORS button.
Then
appears in the display.
Enter the diagnostic test mode.
Push and hold the WHITES & COLORS and DELICATES at the same time.
After that push PERM. PRESS button for 3 times. Push START button.
Press the WHITES & COLORS button.
Then
appears in the display.
Enter the diagnostic test mode.
1
Pressing the START button cycles to the next test function.
Number of times the START
button is pressed
None
1 time
2 times
3 times
4 times
5 times
6 times
7 times
During check, if the door is open.
During check, if the door is closed
Checking point
Check the version and code of machine.
■ ELECTRIC COIN TYPE : AU:OE
■ ELECTRIC OPL TYPE : CA:PE
■ GAS COIN TYPE : AU:Og
■ GAS OPL TYPE : CA:Pg
PDA CHECK
Motor runs.
■ ELECTRIC TYPE: Heater runs.
Motor + Heater 1 (2250W)
■ GAS TYPE: GAS valve runs.
Motor + Valve
■ ELECTRIC TYPE: Heater runs.
Motor + Heater 1 (2250W) + Heater 2 (2250W)
■ GAS TYPE: GAS valve runs.
Motor+Valve
LED & KEY CHECK
Press WHITES & COLORS button.
Press PERM. PRESS button.
Press DELICATES button.
Press NO HEAT button
Test ends.
Door switch
(Motor & Heater Off, Buzzer beeps seven times)
Test goes back at step 2.
(Motor on & Heater Off)
Display
LqC 1
Version and code of machine (All LED on)
COIN machine displays AU:OE or AU:Og and gU:XX
alternately. OPL machine displays CA:PE or CA:Pg and gU:XX
alternately. XX is the version number
Ir-Measured moisture value (70~239)
Current temperature (5~70)
(Displays the temperature inside the drum in °
Celsius.)
Current temperature (5~70)
(Displays the temperature inside the drum in °
Celsius.)
Version and code of machine
LqC1
dE
(The door is open. Please close the door completely)
Measured moisture value (70~239)
Note
During LqC1 test, if no buttons are pressed for 4 minutes, machine will be turned off automatically.
Do not use
.
34
Part 5
PROGRAMMING MODE - Test Mode
2 Factory reset - EEPt
After a factory reset, all values are reset to the default values.
Button
Entering set up mode.
You will see LqC1
Display
Press the PERM. PRESS or the DELICATES
Button until
appears in the display.
Press the START button.
Press the PERM. PRESS button until
display.
appears in the
Press the START button, then factory reset is done.
is displayed.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
• OPL type - Push “WHITES&COLORS” + “DELICATES”
and the ‘3’.
Note
• Dryer default value for CARD/COIN machine.
- Drying time
45 Minute
- Top off time
15 Minute
• Drying time in OPL machine can be changed from 10 to 100 Minutes by pressing the cycle button.
35
Part 5
PROGRAMMING MODE - Test Mode
3 Time Set Up
Button
Entering set up mode.
You will see LqC1
Press the PERM. PRESS or the DELICATES button until
appears in the display.
Press the START button.
The display cycles through 2000 --> 0101 --> Sat --> 0000.
Press the START button.
Press PERM. PRESS (+) or DELICATES(-) button to select
year between 2000 and 2099.
Press the START button.
The machine sets up the year, then advances to the next
process automatically.
Press PERM. PRESS (+) or DELICATES(-) button to select
month between 01 and 12.
Press the START button.
The machine sets up the month, then advances to the next
process automatically.
Press PERM. PRESS (+) or DELICATES(-) button to select
day between 01 and 31.
Press the START button.
The machine sets up the day, then advances to the next
process automatically.
Press PERM. PRESS (+) or DELICATES(-) button to select
hour between 00 and 23.
Press the START button.
The machine sets up the hour, then advances to the next
process automatically.
Press PERM. PRESS (+) or DELICATES(-) button to select
minute between 00 and 59.
Press the START button.
The machine sets up the minute.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1. Control panel open.
2. Turn on/off toggle switch.
36
Display
Part 5
PROGRAMMING MODE - Test Mode
4 Courtesy cycle
Courtesy cycle is like a complimentary cycle given to the customer when the dryer goes out of order when the
customer has made the payment to dry one’s clothes.
Button
Entering set up mode.
You will see LqC1
Display
Press the PERM. PRESS or the DELICATES
Button until
appears in the display.
Press the START button.
Press the PERM. PRESS button until
appears in the display.
Press the START button.
Display will show
.
Select the course you desire.
Note
• In case of dryer card type, it has to insert the cash card
after removing the service card. Then press the cycle
course and the start button. (It is only applicable to the
dryer’s card type specially and there is no subtraction in
card balance at the Courtesy cycle.)
Press the START button.
Display will show the remaining time and start.
37
Part 5
PROGRAMMING MODE - Test Mode
5 Cycle Kill
Coin
Button
Entering set up mode.
You will see LqC1
Display
Press the PERM. PRESS or the DELICATES
Button until
appears in the display.
Press the START button.
Press the PERM. PRESS button until
appears in the display.
Press the START button.
Display
with beeping.
Go back to ready mode.
Card type
Descriptions
Insert
cycle kill card.
Display the current time and
Display
with beeping.
Go back to ready mode.
Note
OPL type
- Dryer machine will end the cycle by opening the door.
38
Display
.
Part 5
PROGRAMMING MODE - Collect Mode
Collect Information Data : CLCt (display)
The dryer collects the usage data so that the owner can check various information like number of various cycles used,
how many times card or coins used, etc.
Entering the collect mode
Data Name
Entering
the collect
mode
Step (Button)
LED Display
Description
1. Entering the programming mode.
Insert service card(card type), Turn on/off toggle switch (Coin type).
2. WHITES & COLORS
Press the WHITES & COLORS button until "tESt" appears in the
display.
3. DELICATES
Press the PERM. PRESS or DELICATES button until "CLCt"
appears in the display.
4. START
Enter the Collect information data.
5. PERM. PRESS or
DELICATES
Move to each data list that you want to check by pressing with
PERM. PRESS or DELICATES button.
6. START
Display the value of selected data list
Check the collect information reference to the follow lists. The Lists are displayed by abbreviations.
Collect Mode Data lists
Description
Meaning
No.
Abbreviation
1
rgPr
Regular Price
$0.00 ~ $10.00
2
rgCP
Regular Cold Price
rgCP is not available in dryer. (It can't enter.)
3
rgrP
Regular Warm Price
rgrP is not available in dryer. (It can't enter.)
4
rgHP
Regular Hot Price
rgHP is not available in dryer. (It can't enter.)
5
dELC
Dryer Moisture Sense
dELC is not available in dryer. (It can't enter.)
6
ItrC
Interval Regular Cycles
Number of Regular cycles ( 0~65535 )
7
ItCC
Interval Regular Cold Cycles
ItCC is not available in dryer. (It can't enter.)
8
ItAC
Interval Regular Warm Cycles
ItAC is not available in dryer. (It can't enter.)
9
ItHC
Interval Regular Hot Cycles
ItHC is not available in dryer. (It can't enter.)
10
ItSC
Interval Super Cycles
ItSC is not available in dryer. (It can't enter.)
11
IttF
Interval Topoff Cycles (Dryer Only)
Number of Topoff cycles ( 0~65535 )
12
ItUC
Interval Service Cycles
Number of Service cycles (0~65535)
13
ItFC
Interval Token Cycles
Number of Token cycles (0~65535)
14
ACrC
Accumulated Regular Cycles
Number of Regular cycles ( 0~65535 )
15
ACCC
Accumulated Regular Cold Cycles
ACCC is not available in dryer. (It can't enter.)
16
ACAC
Accumulated Regular Warm Cycles
ACAC is not available in dryer. (It can't enter.)
17
ACHC
Accumulated Regular Hot Cycles
ACHC is not available in dryer. (It can't enter.)
18
ACSC
Accumulated Super Cycles (Washer Only)
ACSC is not available in dryer. (It can't enter.)
19
ACtF
Accumulated Topoff Cycles (Dryer Only)
Number of Topoff cycles ( 0~65535 )
20
ACUC
Accumulated Service Cycles
Number of Service cycles ( 0~65535 )
21
ACFC
Accumulated Token Cycles
Number of Token cycles (0~65535)
22
ACrt
Accumulated Run Time
Number of Running minutes ( 0~65535 )
39
Part 5
PROGRAMMING MODE - Collect Mode
Collect Mode Data lists
Description
Meaning
No.
Abbreviation
23
Itnr
Interval No Runs
Itnr is not available in dryer.
24
Ittb
Interval Trouble Cycles
Ittb is not available in dryer.
25
ItPd
Interval Power Downs
Number of power down
26
Itdd
Interval Unauthorized Service Door Openings
Number of Unauthorized Service Door Openings ( 0~ 255)
27
ItAd
Interval Authorized Service Door Openings
Number of Unauthorized Service Door Openings ( 0~ 255)
28
ItUC
Interval Unauthorized Coin Vault Openings
Number of Authorized Service Door Openings ( 0~ 255)
29
ItAC
Interval Authorized Coin Vault Openings
Number of Authorized Service Door Openings ( 0~ 255)
30
tLdo
Time of Last Service Door Opening
tLdo is not available in dryer.(It can't enter.)
31
tLCo
Time of Last Coin Vault Opening
tLCo is not available in dryer.(It can't enter.)
32
tPdo
Time of Previous Service Door Opening
tPdo is not available in dryer.(It can't enter.)
33
tPCo
Time of Previous Coin Vault Opening
tPCo is not available in dryer.(It can't enter.)
34
SCPr
Super Cycle Price
Scpr is not available in dryer. (It can't enter.)
35
toPr
Top Off Price
$0.00 ~ $10.00
36
Itd
Interval Money
Amount of money for regular cycle($0 ~ $65535)
37
ACd
Accumulated Money
Amount of money for regular cycle($0 ~ $65535)
38
Ittd
Interval Topoff Money
Amount of money for Topoff($0 ~ $65535)
39
ACtd
Accumulated Topoff Money
Amount of money for Topoff($0 ~ $65535)
INTERVAL means collecting since last data collection.
ACCUMULATED means collecting over a period of time since last factory reset (EEPt).
Authorized: Turning on/off the toggle switch with PDA Communication.
(Turning on/off the toggle switch within 30 minutes after Communicating with PDA)
Unauthorized: Turning on/off the toggle switch without PDA Communication.
These items (No.30~33) are not applied this program.
40
Part 6
MAINTENANCE
Regular cleaning
WARNING: To reduce the risk of fire, electric
Cleaning the Lint Filter
Always clean the lint filter after every cycle.
shock, or injury to persons when using this appliance,
follow basic precautions, including the following:
• Unplug the dryer before cleaning to avoid the risk of
electric shock. Failure to follow this warning can cause
serious injury, fire, electric shock, or death.
• Never use harsh chemicals, abrasive cleaners, or
solvents to clean the washer. They will damage the
finish.
Cleaning the Exterior
Proper care of your dryer can extend its life.
The outside of the machine can be cleaned with warm
water and a mild, nonabrasive household detergent.
Immediately wipe off any spills with a soft, damp cloth.
Note
Lint Filter
To clean, open the dryer door and pull the lint filter
straight up.Then:
1. Roll any lint off the filter with your fingers, or
Do not use methylated spirits, solvents, or similar
products.
Never use steel wool or abrasive cleansers; they can
damage the surface.
Cleaning the Interior
Wipe around the door opening and seal with a soft, damp cloth to
prevent lint and dust buildup that could damage the door seal.
Clean the window with a soft cloth dampened with warm water and a
mild, nonabrasive household detergent; then wipe dry.
The stainless steel drum can be cleaned with a conventional stainless
steel cleaner, used according to the manufacturer’s specifications.
Never use steel wool or abrasive cleansers; they can scratch or
damage the surface.
2. Vacuum the lint filter, or
Cleaning Around and Under the Dryer
Vacuum lint and dust from around the dryer and
underneath it regularly. Vent ductwork should be checked
for lint buildup and cleaned at least once per year. If any
noticeable reduction in airflow or drying performance
occurs, immediately check ductwork for obstructions and
blockages.
3. If the lint filter has become very dirty or clogged with
fabric softener, wash the lint filter in warm, soapy water
and allow to dry thoroughly before reinstalling.
Maintaining Ductwork
Vent ductwork should be checked for lint buildup and
cleaned at least once per year. If any noticeable reduction
in airflow or drying performance occurs, immediately check
ductwork for obstructions and blockages. Contact a
qualified technician or service provider.
Note
NEVER operate the dryer without the lint filter in
place. NEVER operate the dryer with a wet lint filter.
41
Part 7
STACK MACHINE INSTALLATION INSTRUCTIONS
1 SUITABLE MODEL FOR STACKING
STACK
POSITION
STACK
POSITION
UPPER
Dryer
LOWER
Washer
RN1329AD5S / RV1329AD5S
RN1329AN7S / RV1329AN7S
RN1329A7S / RV1329A7S
F1069FD6
F1069FD
F1069FD2
Dryer
Dryer
RN1329AD5 / RV1329AD5
RN1329AN7 / RV1329AN7
RN1329A7 / RV1329A7
RN1329AD6 / RV1329AD6
RN1329AN1 / RV1329AN1
RN1329A1 / RV1329A1
2 STACKING KIT (WASHER & DRYER)
- STACKING KIT is provided in the upper dryer.
P/No.: AGF30609820
- STACKING KIT includes the stacking bracket(1), security bracket(3), bolt(1), screw(9).
1) Stacking bracket
2) bolt
3) Screw
- SLIDING KIT includes the slide bracket(2), sliding pad(4), screw(18).
1) Sliding bracket
4) security bracket
2) Sliding pad
3) Screw
3 STACKING KIT (DRYER & DRYER)
- STACKING KIT is provided in the upper dryer.
P/No.: AGF30609819
- STACKING KIT includes the stacking bracket(1), security bracket(3), bolt(1), screw(9).
1) Stacking bracket
2) bolt
3) Screw
4) security bracket
Note
- The machine can be stacked only on the model designated as suitable by LGE.
- Do not stack the washer on the top.
- You can order the parts for stacking from Qualified dealer or Qualified SVS agent of LGE.
42
Part 7
STACK MACHINE INSTALLATION INSTRUCTIONS
4 Stacking the machine (WASHER & DRYER)
- Install two sliding brackets on the top plate of lower washer.
- Remove the legs from the leg brackets.
- Remove the four(4) leg brackets from the bottom of upper dryer.
- Assemble the four(4) slide pads on the base.
*Security bracket installation (Only coin model)
- Install two security bracket on the panel frame and top plate in the lower
washer.
- Install one security bracket on the lower panel frame in the upper dryer.
- Lift and stack the upper dryer on the lower washer.
- Set the rear of the upper dryer and the rear of the lower washer in the same position.
- Push the upper dryer matching the slide & stacking bracket to make upper and lower front parallel.
- Install the stacking bracket at the rear of the stacked dryer and washer.
- Assemble the six(6) screw to fix the lower machine and upper dryer.
Note
Please refer to Service Manual for detail to explain how to stack and fix the machine
43
Part 7
STACK MACHINE INSTALLATION INSTRUCTIONS
5 Stacking the machine (DRYER & DRYER)
*Security bracket installation (Only coin model)
- Install two security bracket on the panel frame and top plate in the lower dryer.
- Install one security bracket on the lower panel frame in the upper dryer.
- Stack the upper dryer onto the lower dryer.
- Disassemble the lower panel frame.
- Install the bolt to fix the lower machine and upper dryer.
- Locate the stacking bracket on the rear of stacked machine.
- Assemble the six screw to fix the lower machine and upper dryer.
Note
Please refer to Service Manual for detail to explain how to stack and fix the machine
44
Part 8
ERROR MODE
Meaning of Error Codes that LED displays during occurrence or problem.
Dryer error code
PROBLEM
Part 9
POSSIBLE CAUSE
SOLUTION
It is displayed when thermistor is opened or shorted
Thermistor should be replaced.
It is displayed when thermistor temperature have
increased about 17 degrees for 10 seconds
Thermistor should be replaced.
Disconnection of card reader wire.
Check the card reader wire.
POWER FAIL RECOVERY
In case of power failure the machine stops running but the time display remains on, showing the time just before
power failure.
Press the START button after the power is restored, then the machine will restart.
Part 10
DEFAULT DRYER SETTINGS
Default
Default Settings
Cycle Time (Minutes)
45 Minutes
Cool Down Time Cycle
2 Minutes
High Temperature
154.4° F (68° C)
Medium Temperature
140° F (60° C)
Low Temperature
125.6° F (52.5° C)
Top Off Time (Minutes per coin)
15 Minutes
Coin #1 Value
$1.00
Coin #2 Value
$1.00
Minutes/Minutes and seconds
Minutes
Fahrenheit/Celsius
Fahrenheit
Error Mode
On
45
MEMO
46
MEMO
47
Download PDF