LG | RV1329A4 | LG RV1329A4 Owner’s Manual

OWNER’S MANUAL
COMMERCIAL DRYER
Please read this manual carefully before operating
your dryer and retain it for future reference.
MODEL
RN1329AD1 / RV1329AD1
RN1329AD6 / RV1329AD6
RN1329AD5S / RV1329AD5S
MFL62512853
RN1329AN4 / RV1329AN4
RN1329AN1 / RV1329AN1
RN1329AN7S / RV1329AN7S
RN1329A4 / RV1329A4
RN1329A1 / RV1329A1
RN1329A7S / RV1329A7S
www.lg.com
2
PRODUCT FEATURES
PRODUCT FEATURES
OUTSTANDING PERFORMANCE
The dryer features the largest capacity, quick drying times, quiet operation, and an energy-saving system.
ARTISTIC DESIGN
Modern front panel look and big clear glass door make your dryer look stylish
EASY OF USE
An entire selection of user-friendly functions makes operating the dryer easy.
ULTRA CAPACITY
The larger drum enables better tumbling and less tangling and wrinkling of the laundry.
IMPORTANT SAFETY INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, Injury to persons, or death.
Your Safety and the safety of others is very important.
e have provided many important safety messages in this manual and on your appliance.
W
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.
These words mean:
w
wDANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
wWarning
You can be killed or seriously injured if you don’t follow instructions.
wCAUTION
ou may be slightly injured or cause damage to the product if you do not follow instructions.
Y
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are not followed.
BASIC SAFETY PRECAUTIONS
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
• Read all instructions before using the dryer.
• Keep area around the exhaust opening and adjacent surrounding
• Before use, the dryer must be properly installed as described in this
areas free from the accumulation of lint, dust, and dirt.
manual.
• The interior of the dryer and exhaust vent should be cleaned
• Do not place items exposed to cooking oils in your dryer. Items
periodically by qualified service personnel.
contaminated with cooking oils may contribute to a chemical
• Do not install or store the dryer where it will be exposed to the
reaction that could cause a load to catch fire.
weather.
• Do not dry articles that have been previously cleaned in, washed in,
• Always check the inside of the dryer for foreign objects.
soaked in, or spotted with gasoline, dry-cleaning solvents, or other
• Clean lint screen before or after each load.
flammable or explosive substances as they give off vapors that
• Do not dry unwashed items in the tumble dryer.
could ignite or explode.
• Items that have been soiled with substances such as cooking oil,
• Do not reach into the dryer if the drum or any other part is moving.
acetone, alcohol,petrol,kerosene,spot removers, turpentine, waxes
• Do not repair or replace any part of the dryer or attempt any
and wax removers should be washed in hot water with an extra
servicing unless specifically recommended in this Use and Care
amount of detergent before being dried in the tumble dryer.
Guide or in published user-repair instructions that you understand
• Items such as foam rubber(latex foam), shower caps, waterproof
and have the skills to carry out.
textiles, rubber backed articles and clothes or pillows fitted with
• Do not tamper with controls.
foam rubber pads should not be dried in the tumble dryer.
• Before the dryer is removed from service or discarded, remove the
• Fabric softeners, or similar products, should be used as specified by
door to the drying compartment.
the fabric softener instructions.
• Do not allow children to play on or in the dryer. Close supervision of
• The final part of a tumble dryer cycle occurs without heat(cool
children is necessary when the dryer is used near children.
down cycle) to ensure that the items are left at a temperature that
• Do not use fabric softeners or products to eliminate static unless
ensures that the items will not be damaged.
recommended by the manufacturer of the fabric softener or
• If the supply cord is damaged, it must be replaced by the
product.
manufacturer, its service agent or similarly qualified persons in
• Do not use heat to dry articles containing foam rubber or similarly
order to avoid a hazard.
textured rubber-like materials.
wWarning
Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
• The lint trap has to be cleaned frequently, if applicable.
• This appliance is not to be used by children or persons with
• Lint must not to be allowed to accumulate around the tumble
reduced physical, sensory or mental capabilities, or lack of
dryer.
experience and knowledge, unless they have been given
• Adequate ventilation has to be provided to avoid the back flow
supervision or instruction.
of gases into the room from appliances burring other fuels,
• Children should be supervised not to play with the appliance.
including open fires.
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Disposal of your old appliance
1. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
2. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
3. For more detailed information about disposal of your old appliance, please contact
your city office, waste disposal service or the shop where you purchased the product.
■ What is not covered.
Service trips to your home to instruct you on the product.
If the product is connected to any voltage other than that shown on the rating plate.
If the fault is caused by accidents, neglects, misuses of Acts of God.
If the fault is caused by reasons except for normal domestic use or use in accordance with the owner’s manual.
If the fault is caused by pests, for example, rats or cockroaches etc..
Noise or vibration that is considered normal,for example, water drain sound, spin sound or warning beeps.
Correcting the installation for example, leveling the product, adjustment of drain.
Normal maintenance recommended by the owner’s manual.
Removal of foreign objects/substances from the machine including the pump and inlet hose filter, for example,
grit,nails, bra wires and buttons etc..
Replace fuses in or correct wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects with this appliance.
If this product is used for commercial purposes, it is not warranted.
(Example:Public places such as public bathroom, lodging house, training center, dormitory)
If the product is installed outside the normal service area, any cost of transportation involved in the repair of the
products, or the replacement of a defective part, shall be borne by the owner.
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, Injury to persons, or death.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this appliance
or any other appliances.
• Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
WHAT TO DO IF YOU SMELL GAS: (Applicable for Gas models)
1. Do not try to light a match or cigarette, or turn on
any gas or electrical appliance.
2. Do not touch any electrical switches. Do not use
any phone in your building.
3. Clear the room, building, or area of all occupants.
4. Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions carefully.
5. If you cannot reach your gas supplier, call the fire
department.
IMPORTANT SAFETY INSTRUCTIONS
5
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least
resistance for electric current. This appliance must be
equipped with a cord having an equipmentgrounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not use an adapter or extension cord. Do not remove
ground prong. If you don’t have the proper outlet,
consult an electrician.
Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
This appliance must be connected to a grounded metal,
permanent wiring system or an equipmentgrounding
conductor must be run with the circuit conductors and
connected to the equipmentgrounding terminal or lead
on the appliance.
Electric shock can result if the dryer is not properly
grounded.
wWarning
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with
a qualified electrician or service person if you are in doubt as to whether the appliance is properly grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•P
roperly ground dryer to conform with all
governing codes and ordinances. Follow details in
the installation instructions. Electric shock can result
if the dryer is not properly grounded.
•B
efore use, the dryer must be properly installed as
described in this manual. Electric shock can result if
the dryer is not properly grounded.
• I nstall and store the dryer where it will not be
exposed to temperatures below freezing or
exposed to the weather.
•A
ll repairs and servicing must be performed
by an authorized servicer unless specifically
recommended in this Owner’s Guide. Use only
authorized factory parts. Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
•T
o reduce the risk of electric shock, do not install
the dryer in humid spaces. Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
•C
onnect to a properly rated, protected, and sized
power circuit to avoid electrical overload. Improper
power circuit can melt, creating electric shock and/or
fire hazard.
• Remove all packing items and dispose of all
shipping materials properly. Failure to do so can
result in death, explosion, fire, or burns.
• Place dryer at least 18 in. above the floor for a
garage installation. Failure to do so can result in
death, explosion, fire, or burns.
• Keep all packaging from children. Packaging
material can be dangerous for children. There is a
risk of suffocation.
• Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc. Failure to do so can
result in fire.
• Do not place candles, smoking materials, or other
flammables on to top of the product. Dripping wax,
smoke, or fire can result.
• Remove all protective vinyl film from the product.
Failure to do so can cause product damage, smoke or
fire.
6
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR INSTALLATION
Exhaust/Ducting:
•G
as dryers MUST be exhausted to the outside.
Failure to follow these instructions can result in fire or
death.
•T
he dryer exhaust system must be exhausted
to the outside of the dwelling. If the dryer is not
exhausted outdoors, some fine lint and large
amounts of moisture will be expelled into the
laundry area. An accumulation of lint in any area of
the home can create a health and fire hazard.
•U
se only rigid metal or flexible metal 4-in. diameter
ductwork inside the dryer cabinet or for exhausting
to the outside. Use of plastic or other combustible
ductwork can cause a fire. Punctured ductwork
can cause a fire if it collapses or becomes otherwise
restricted in use or during installation.
•D
uctwork is not provided with the dryer, and you
should obtain the necessary ductwork locally. The
end cap should have hinged dampers to prevent
backdraft when the dryer is not in use. Failure to
follow these instructions can result in fire or death.
• The openings must not be obstructed by a carpet.
• E xhaust air must not be discharged into a flue which
Is used for exhausting fumes from appliances burning
gas or other fuels.
• The exhaust duct must be 4 in. (10 cm) in diameter
with no obstructions. The exhaust duct should be
kept as short as possible. Make sure to clean any
old ducts before installing your new dryer. Failure
to follow these instructions can result in fire or death.
• Rigid or semi rigid metal ducting is recommended
for use between the dryer and the wall. In special
installations when it is impossible to make a
connection with the above recommendations, a ULlisted flexible metal transition duct may be used
between the dryer and wall connection only. The
use of this ducting will affect drying time. Failure to
follow these instructions can result in fire or death.
• DO NOT use sheet metal screws or other fasteners
which extend into the duct that could catch lint and
reduce the efficiency of the exhaust system. Secure
all joints with duct tape. For complete details,
follow the Installation Instructions. Failure to follow
these instructions can result in fire or death.
IMPORTANT SAFETY INSTRUCTIONS
7
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•D
o not, under any circumstances, cut or remove
the ground prong from the power cord. To prevent
injury to persons or damage to the dryer, the electrical
power cord must be plugged into a properly grounded
outlet.
•F
or personal safety, this dryer must be properly
grounded. Failure to do so can result in electric shock
or injury.
•R
efer to the installation instructions in this manual
for specific electrical requirements for your model.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•T
his dryer must be plugged into a properly
grounded outlet. Electric shock can result if the
dryer is not properly grounded. Have the wall
outlet and circuit checked by a qualified electrician
to make sure the outlet is properly grounded.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
• Never unplug your dryer by pulling on the power
cord. Always grip plug firmly and pull straight out
from the outlet. The power cord can be damaged,
resulting in a risk of fire and electric shock.
• Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end. The power cord can
melt, creating electric shock and/or fire hazard.
• When installing or moving the dryer, be careful not
to pinch, crush, or damage the power cord. This will
prevent injury and prevent damage to the dryer from
fire and electric shock.
• To reduce the risk of injury to persons, adhere
to all industry recommended safety procedures
including the use of long sleeved gloves and safety
glasses. Failure to follow all of the safety warnings in
this manual could result in property damage, injury to
persons or death.
•T
he dryer should always be plugged into its own
individual electrical outlet which has a voltage
rating that matches the rating plate. This provides
the best performance and also prevents overloading
house wiring circuits which could cause a fire hazard
from overheated wires.
SAVE THESE INSTRUCTIONS
8
CONTENTS
CONTENTS
2
PRODUCT FEATURES
29
30
3
IMPORTANT SAFETY
INSTRUCTIONS
3
5
5
7
BASIC SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS
SAFETY INSTRUCTIONS FOR INSTALLATION
SAFETY INSTRUCTIONS FOR CONNECTING
ELECTRICITY
31
32
33
34
9
SPECIFICATIONS
10 IDENTIFICATION
13 OPERATING YOUR DRYER
14 PROGRAMMING MODE
15 PROGRAMMING MODE
- COIN/CARD
16 PROGRAMMING MODE - OPL
17 PROGRAMMING MODE
- Setup Mode
17 1. How to change regular price.
18 2. How to change special price
19 3. H
ow to enter the FEA1
20 3-1. Special price day setup
21 3-2. Vend type setup - card type or coin
type setup
22 3-3. Top off apply or not setup
23 4. How to enter the special price day setup
24 4-1. How to change sunday
25 5. Special price beginning time setup
26 6. Special price ending time setup
27 7. Regular priced dryer cycle time
28 8. Special priced dryer cycle time
9. Value of coin 1
10. Value of coin 2 (Set up for top off price
and e-suds coin pulse)
11. Penny increment pricing offset
12. Top off time
13. Beep volume
14. Time to keep the coin (Use only for coin
type)
35 PROGRAMMING MODE
- Test Mode
36
37
38
39
40
1. LqC1
2. Factory reset - EEPt
3. Time Set Up
4. Courtesy cycle
5. Cycle Kill
41 PROGRAMMING MODE
- Collect Mode
43 MAINTENANCE
44 STACK MACHINE INSTALLATION
INSTRUCTIONS
46 ERROR MODE
46 POWER FAIL RECOVERY
46 DEFAULT DRYER SETTINGS
SPECIFICATIONS
9
SPECIFICATIONS
■ Type : Electric and Gas Dryer
■ Rating
: Please refer to the rating label regarding detailed information.
■ Single dryer size
: 686mm(W) x 764mm(D) x 983mm(H)
■ Stack dryer size : 686mm(W) x 764mm(D) x 1954mm(H)
■Capacity : 10Kg
■ Weight : 59.4 kg
■ Specifications are subject to change by manufacturer.
NOTE
Specifications subject to change by manufacturer.
10
IDENTIFICATION
IDENTIFICATION
■ CARD TYPE
- SIDE BY SIDE(RN1329AD1, RV1329AD1)
- STACK UPPER(RN1329AD5S, RV1329AD5S)
- STACK LOWER(RN1329AD6, RV1329AD6)
4
1
2
4
3
4
1
2
■ OPL TYPE
- SIDE BY SIDE(RN1329A4, RV1329A4)
- STACK UPPER(RN1329A7S, RV1329A7S)
- STACK LOWER(RN1329A1, RV1329A1)
4
1
2
4
1
2
3
3
1. DISPLAY LED
3. START BUTTON
2. CYCLE BUTTON
4. STATUS LED
3
4
1
2
IDENTIFICATION
3
■ COIN TYPE
- SIDE BY SIDE(RN1329AN4, RV1329AN4)
3
4
1
2
4
1
2
4
1
2
3
3
3
■ COIN TYPE
1
2
- STACK4 UPPER(RN1329AN7S,
RV1329AN7S)
3
4
1
2
4
1
2
3
3
4
1
2
4
1
23
■ COIN TYPE
- STACK LOWER(RN1329AN1, RV1329AN1)
4
1
2
3
3
3
4
1
2
2. CYCLE4BUTTON
1
2
4
1
2
1. DISPLAY LED
3. START BUTTON
4. STATUS LED
11
12
IDENTIFICATION
STATUS LED
DISPLAY LED
CYCLE BUTTON
4
1
2
3
START BUTTON
1 DISPLAY LED
The Display shows the vend price, remaining time, and
programming options.
Error codes are also displayed here.
3 START BUTTON
The Start LED flashes when the full vend price has been
satisfied then the cycle has been chosen or the machine
is paused.
The Start LED flashes when a card is inserted to add time
to the current cycle.
2 CYCLE BUTTON
Press the cycle button to Select the desired cycle based
on laundry types and conditions.
4
High Temp.
Use this cycle to get high heat for heavy fabrics, such
as jeans corduroys or work clothes (High heat).
Med Temp.
Use for drying sturdy fabrics such as work casual
clothes (Medium heat).
Low Temp.
Use for drying synthetic fabrics,washable knit fabrics
and no-iron finishes (Low heat).
No Heat
Use for items that require heat-free drying such as
plastics or rubber.
STATUS LED
LED
Description
LED flashes whenever the heating cycle
is in operation.
LED flashes whenever the cool down
cycle is in operation.
OPERATING YOUR DRYER
13
OPERATING YOUR DRYER
1. Ready mode
1) Coin / Card type
- The cycle LEDs flash at the same time, when the
price of cycles are equal.
2) OPL type
- The cycle LEDs is lit at the same time, and displayed
‘PUSH’.
2. Insert card/coin (not for OPL type)
■ Insert a cash card that has a sufficient balance.
The card balance should be more than the
programmed vend price for a selected cycle.
NOTE
When the card balance is not enough, machine
displays the balance for 5 seconds and then displays
message repetitively
■ Insert a sufficient amount of change that is a more
than the programmed vend price for a selected cycle.
NOTE
When the coin amount is not enough, the machine
will not start.
3. Select the cycle
Press the desired cycle and the start button. The display
LED will show the remaining time and the selected cycle
starts.
NOTE
The last 2 minutes of the remaining time are always
for the cool down portion.
4. Top off (To add more time)
■A
fter a debit card is inserted, the operating time can
be increased to 15 minutes/$1.00 (default), when the
Start button or the chosen course button has been
pressed.
(The card should have enough balance to satisfy
increasing time.)
■ T he operating time can be increased to 15
minutes/$1.00 (default) by adding more coins.
NOTE
Owner can control the additional time and money
setting (top off price).
When the COOL DOWN has been working, if time is
added, it goes back to the DRYING.
Time can be added up 99 minutes.
5. Change cycle
■Y
ou cannot change the cycle while the machine is
running.
■B
ut if the door is opened, the machine stops
temporarily and the cycle can be changed.
6. Cycle finish
■A
fter the COOL DOWN of cycle, the machine stops
and LED display shows End.
If you press any key or open the door, the dryer
defaults to the ready mode.
14
PROGRAMMING MODE
PROGRAMMING MODE
1. Programming mode
You can check machine information or change setting on Program setup or Diagnostic test.
There are two methods that you can enter programming mode.
■ How to enter “Programming mode”
■ How to use button
You can enter programming mode only for Idle state
and pause state.
You can change Dryer vend price, cycle time and Cycle
parameters, etc.
- Card Type
Press button
Description
High Temp.
Move to upper level
Med Temp.
Move to the mode in the
same level (+)
Low Temp.
Move to the modes in the
same level (-)
No Heat
-
Start
Enter the selected mode
1) Insert service card.
2) Display will show
- Coin Type
1) Dissemble upper coin box key.
2) Take out the coin drop from the coin box.
3) Turn on/off the toggle switch at the back of the coin
box.
4) Display will show “
”.
- OPL Type
1) Push the High Temp. and Low Temp. button at the
same time.
2) Push the Med Temp. button 3 times.
3) Push the Srart button.
4) Display will show “
”
Coin Box Key
Coin Vault
COIN TYPE
Insert debit card
CARD TYPE
OPL TYPE
NOTE
• If you turn on the power without connecting the meter case for the first time, the machine will display
• When the machine comes from the factory, it is set in the coin type. You can change Card/Coin type by button.
.)
(For more information refer to SETUP mode’s
• The machine will display “PUSH” for OPL type
• Do not enter the “Vend type set up” mode if the machine is a coin type. You cannot restore it back to Coin type
without a special card reader and a service card after it has been changed to Card type in the set up mode.
.
PROGRAMMING MODE
PROGRAMMING MODE - COIN/CARD
■ Algorithm Flow Chart shows how to control programming mode.
■ Before program set, check the structure of programming mode.
1. Turn on/off toggle switch or Insert the service card to entering set up mode.
2. Press High Temp. button to move the upper level.
3. Press Med Temp.(+) or Low Temp.(-) button if you want to be at the same level.
4. Press Start button to enter the details of Set up, Diagnostic Tests mode.
is to set price value, time value and vend type etc.
consists of line test, reset, free cycle and kill cycle.
Is to collect the usage data.
■ STRUCTURE OF PROGRAMMING MODE
NOTE
• Do not use
,
.
• It is only used in inspecting the machine.
15
16
PROGRAMMING MODE
PROGRAMMING MODE - OPL
■ Algorithm Flow Chart shows how to control programming mode.
■ Before program set, check the structure of programming mode.
OPL Type
1) Push the High Temp. and Low Temp. button at the same time.
2) Push the Med Temp. button 3 times.
3) Push the Start button.
4) Display will show “
“
is to set price value, time value and vend type etc.
consists of line test, reset, free cycle and kill cycle.
Is to collect the usage data.
■ STRUCTURE OF PROGRAMMING MODE
NOTE
• Do not use
,
.
• It is only used in inspecting the machine.
PROGRAMMING MODE
PROGRAMMING MODE - Setup Mode
Setup Mode :
(display)
■ You can change dryer vend price, cycle time, and cycle parameters, etc.
■ Entering set up mode
• Coin type - Turn on/off toggle switch.
• Card type - Insert the service card.
• Stack type - Take off control panel, and turn on/off toggle switch.
• OPL type – Push “High Temp.” + “Low Temp.” and the ‘3’.
• Then, dryer displays
.
1. How to change regular price.
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Start button.
Display previous regular price.
Press Med Temp.(+) or Low Temp.(-) button to set regular price.
(The vend price can be set from 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the regular price, then advances to the
next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
• rgCP (regular cold price) is not available in dryer.
• rgrP (regular warm price) is not available in dryer.
• rgHP (regular hot price) is not available in dryer.
Display
17
18
PROGRAMMING MODE
2. How to change special price
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special price.
Press Med Temp.(+) or Low Temp.(-) button to set special price.
(The vend price can be set from 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the regular price, then advances to the
next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
• SPCP (special cold price) is not available in dryer.
• SPrP (special warm price) is not available in dryer.
• SPHP (special hot price) is not available in dryer.
• SCPA (add super cycle price) is not available in dryer.
• SPCt (add super wash type) is not available in dryer.
Display
PROGRAMMING MODE
3. How to enter the
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
■ Structure of
■ Content of
• Special price days apply or not
• Disabled
• Add super wash apply or not
• Select vend type
• This function is not available
• Pre-wash apply or not
• Top off apply or not (only for dryer)
• Disable
• Enable
19
20
PROGRAMMING MODE
3-1. Special price day setup
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Start button.
Press Med Temp. or Low Temp. button and then select
or
.
Disable
Enable
Press the Start button.
The machine sets up the special price, then advances to the next
process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
• CLEE (clear escrow enable or not) is not available in dryer.
• SUUE (add super wash apply or not) is not available in dryer.
One or the other will
display.
PROGRAMMING MODE
21
3-2. Vend type setup - card type or coin type setup
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press Med Temp. or Low Temp. button and then select
or
.
Coin type
Card type
Press the Start button.
The machine sets up the vend type, then go to the idle mode
automatically.
NOTE
• SEdE (sensor dry apply or not) is not available in dryer.
• PrSH (Pre-wash apply or not) is not available in dryer.
One or the other will
display.
22
PROGRAMMING MODE
3-3. Top off apply or not setup
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press Med Temp. or Low Temp. button and then select
or
.
Disable
Enable
Press the Start button.
The machine sets up the Vend type, then advances to the next
process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
One or the other will
display.
PROGRAMMING MODE
4. How to enter the special price day setup
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
■ Structure of
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Display
23
24
PROGRAMMING MODE
4-1. How to change sunday
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display
.
Press the Start button.
Press Med Temp.(+) or Low Temp. button and then select
or
.
Disable
Enable
Press the Start button.
The machine sets up the special price day (Sunday), then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
As explained on the previous page, other days can be set up by the same method.
One or the other will
display.
PROGRAMMING MODE
5. Special price beginning time setup
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special price beginning time.
Press Med Temp.(+) or Low Temp.(-) button to
select time between 0 and 23.
Press the Start button.
The machine sets up the special price beginning time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
Display
25
26
PROGRAMMING MODE
6. Special price ending time setup
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special price ending time.
Press Med Temp.(+) or Low Temp.(-) button to select time
between 1 and 24.
Press the Start button.
The machine sets up the special price ending time, then advances
to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
When setting up a special price period, the ending time must be later than the beginning time.
Display
PROGRAMMING MODE
7. Regular priced dryer cycle time
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous regular priced dryer cycle time.
Press Med Temp.(+) or Low Temp.(-) button to select time
between 10 and 99.
Press the Start button.
The machine sets up the regular priced dryer cycle time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
Display
27
28
PROGRAMMING MODE
8. Special priced dryer cycle time
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous special priced dryer cycle time.
Press Med Temp.(+) or Low Temp.(-) button to select time
between 10 and 99.
Press the Start button.
The machine sets up the special priced dryer cycle time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
• CCCC (washing time) is not available in dryer.
• nrPC (rinsing times per cycle) is not available in dryer.
• rt (rinsing time setup) is not available in dryer.
• tSSd (top spin speed) is not available in dryer.
Display
PROGRAMMING MODE
9. Value of coin 1
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous coin 1 value.
Press Med Temp.(+) or Low Temp.(-) button to select value of
coin 1
(The value can be set fronm 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the value of coin 1, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
Display
29
30
PROGRAMMING MODE
10. Value of coin 2 (Set up for top off price and e-suds coin pulse)
Entering set up
mode.
You will see LqC1
Button
Display
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous coin 2 value.
Press Med Temp.(+) or Low Temp.(-) button to select value of
coin 2
(The value can be set fronm 0 to 10.00 in 1$ increments.)
Press the Start button.
The machine sets up the value of coin 2, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
• Coin type : Value of coin 2 is same function as setting for the e-Suds coin pulse.
• Card type : Value of coin 2 is same function as the top off price.
(As changing the value of coin 2, you can change the top off price and e-Suds coin pulse.)
PROGRAMMING MODE
11. P
enny increment pricing offset
This represents the cent increment price offset used when debit card is setup.
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous penny increment pricing offset.
Press Med Temp.(+) or Low Temp.(-) button to select value
of PIPo. (0~4)
Press the Start button.
The machine sets up the PIPo, then advances to the next process
automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
•P
enny increment pricing offset is available only in card type.
(It hasn’t affected on the coin type’s price setting.)
Display
31
32
PROGRAMMING MODE
12. Top off time
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous top off time.
Press Med Temp.(+) or Low Temp.(-) button to select time
between 1 and 30.
Press the Start button.
The machine sets up the top off time, then advances to the next
process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
Display
PROGRAMMING MODE
13. Beep volume
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous value.
Press Med Temp.(+) or Low Temp.(-) button to select High or
Low or Off.
Press the Start button.
The machine sets up the beep volume, then advances to the next
process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
Display
33
34
PROGRAMMING MODE
14. Time to keep the coin (Use only for coin type)
Entering set up
mode.
You will see LqC1
Button
Press the High Temp. button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
Display previous value.
Press Med Temp.(+) or Low Temp.(-) button to select time
between 1 ~ 180 or ‘Disable’.
Press the Start button.
The machine sets up the time to keep the coin, then advances to
the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
Display
PROGRAMMING MODE
35
PROGRAMMING MODE - Test Mode
Diagnostic tests :
(display)
This program has been added for testing the dryer and detecting errors.
Entering the test mode
Machine
Data
Name
1. Entering
programming
mode
CARD /
COIN
2. High Temp.
Entering
the test
mode
OPL
Button
Display
Description
Insert service card (card type), Turn on/off toggle switch
(Coin type).
Press the High Temp. button.
Then
appears in the display.
3. Start
Enter the diagnostic test mode.
1. Entering
programming
mode.
Push and hold the High Temp. and Low Temp. at the same time.
After that push Med Temp. button for 3 times. Push Start
button.
2. High Temp.
3. Start
Press the High Temp. button.
Then
appears in the display.
Enter the diagnostic test mode.
36
PROGRAMMING MODE
1. Pressing the Start button cycles to the next test function.
Number of times
the Start
button is pressed
Checking point
None
Display
LqC 1
1 time
Check the version and code of
machine.
■ ELECTRIC COIN TYPE : AU:OE
■ ELECTRIC OPL TYPE : CA:PE
■ GAS COIN TYPE : AU:Og
■ GAS OPL TYPE : CA:Pg
Version and code of machine (All LED on)
COIN machine displays AU:OE or AU:Og and gU:XX
alternately. OPL machine displays CA:PE or CA:Pg and
gU:XX alternately. XX is the version number
2 time
PDA CHECK
Ir--
3 time
Motor runs.
Measured moisture value (70~239)
■ ELECTRIC TYPE: Heater runs.
Motor + Heater 1 (2250W)
■ GAS TYPE: GAS valve runs.
Motor + Valve
■ ELECTRIC TYPE: Heater runs.
Motor + Heater 1 (2250W) + Heater
2 (2250W)
■ GAS TYPE: GAS valve runs.
Motor+Valve
LED & KEY CHECK
Press High Temp. button.
Press Med Temp. button.
Press Low Temp. button.
Press No Heat button
Current temperature (5~70)
(Displays the temperature inside the drum in ° Celsius.)
Test ends.
LqC1
4 time
5 time
6 time
7 time
Door switch
During check, if the
(Motor & Heater Off, Buzzer beeps
door is open.
seven times)
During check, if the Test goes back at step 2.
door is closed
(Motor on & Heater Off )
NOTE
Current temperature (5~70)
(Displays the temperature inside the drum in ° Celsius.)
Version and code of machine
dE
(The door is open. Please close the door completely)
Measured moisture value (70~239)
During LqC1 test, if no buttons are pressed for 4 minutes, machine will be turned off automatically.
Do not use
.
PROGRAMMING MODE
2. F
actory reset - EEPt
After a factory reset, all values are reset to the default values.
Entering set up
mode.
You will see LqC1
Button
Display
Press the Med Temp. or the Low Temp. Button until
appears in the display.
Press the Start button.
Press the Med Temp. button until
display.
appears in the
Press the Start button, then factory reset is done.
is displayed.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
NOTE
•D
ryer default value for CARD/COIN machine.
- Drying time 45 Minute
- Top off time 15 Minute
• Drying time in OPL machine can be changed from 10 to 100 Minutes by pressing the cycle button.
37
38
PROGRAMMING MODE
3. Time Set Up
Entering set up
mode.
You will see LqC1
Button
Press the Med Temp. or the Low Temp. button until
appears in the display.
Press the Start button.
The display cycles through 2000 --> 0101 --> Sat --> 0000.
Press the Start button.
Press Med Temp. (+) or Low Temp.(-) button to select year
between 2000 and 2099.
Press the Start button.
The machine sets up the year, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select month
between 01 and 12.
Press the Start button.
The machine sets up the month, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select day
between 01 and 31.
Press the Start button.
The machine sets up the day, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select hour
between 00 and 23.
Press the Start button.
The machine sets up the hour, then advances to the next
process automatically.
Press Med Temp. (+) or Low Temp.(-) button to select minute
between 00 and 59.
Press the Start button.
The machine sets up the minute.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• Stack type - 1
. Control panel open.
2. Turn on/off toggle switch.
• OPL/Coin Type - Press “High Temp.” twice.
Display
PROGRAMMING MODE
4. C
ourtesy cycle
39
Courtesy cycle is like a complimentary cycle given to the customer when the dryer goes out of order when
the customer has made the payment to dry one’s clothes.
Entering set up
mode.
You will see LqC1
Button
Display
Press the Med Temp. or the Low Temp. Button until
appears in the display.
Press the Start button.
Press the Med Temp. button until
display.
Press the Start button.
Display will show
appears in the
.
Select the course you desire.
NOTE
• In case of dryer card type, it has to insert the cash card after
removing the service card. Then press the cycle course and
the start button. (It is only applicable to the dryer’s card type
specially and there is no subtraction in card balance at the
Courtesy cycle.)
Press the Start button.
Display will show the remaining time and start.
40
PROGRAMMING MODE
5. C
ycle Kill
■ Coin
Entering set up
mode.
You will see LqC1
Button
Display
Press the Med Temp. or the Low Temp. Button until
appears in the display.
Press the Start button.
Press the Med Temp. button until
display.
appears in the
Press the Start button.
Display
with beeping.
Go back to ready mode.
■ Card type
Insert
cycle kill card.
Descriptions
Display the current time and
Display
with beeping.
Go back to ready mode.
NOTE
■O
PL type
- Dryer machine will end the cycle by opening the door.
.
Display
PROGRAMMING MODE
41
PROGRAMMING MODE - Collect Mode
Collect Information Data : CLCt (display)
The dryer collects the usage data so that the owner can check various information like number of various cycles
used, how many times card or coins used, etc.
Entering the collect mode
Data Name
Button
Display
2. High Temp.
Entering
the collect
mode
Description
Insert service card(card type), Turn on/off toggle switch (Coin
type).
Press the High Temp. button until “tESt” appears in the
display.
Press the Med Temp. or Low Temp. button until “CLCt” appears in the display.
1. Entering the
programming mode.
3. Low Temp.
4. Start
Enter the Collect information data.
5. Med Temp. or Low
Temp.
Move to each data list that you want to check by pressing
with Med Temp. or Low Temp. button.
6. Start
Display the value of selected data list
❖ Check the collect information reference to the follow lists. The Lists are displayed by abbreviations.
■ Collect Mode Data lists
No.
Abbreviation
Meaning
Description
1
rgPr
Regular Price
$0.00 ~ $10.00
2
rgCP
Regular Cold Price
rgCP is not available in dryer. (It can’t enter.)
rgrP is not available in dryer. (It can’t enter.)
3
rgrP
Regular Warm Price
4
rgHP
Regular Hot Price
rgHP is not available in dryer. (It can’t enter.)
5
dELC
Dryer Moisture Sense
dELC is not available in dryer. (It can’t enter.)
6
ItrC
Interval Regular Cycles
Number of Regular cycles ( 0~65535 )
7
ItCC
Interval Regular Cold Cycles
ItCC is not available in dryer. (It can’t enter.)
8
ItAC
Interval Regular Warm Cycles
ItAC is not available in dryer. (It can’t enter.)
9
ItHC
Interval Regular Hot Cycles
ItHC is not available in dryer. (It can’t enter.)
10
ItSC
Interval Super Cycles
ItSC is not available in dryer. (It can’t enter.)
11
IttF
Interval Topoff Cycles (Dryer Only)
Number of Topoff cycles ( 0~65535 )
12
ItUC
Interval Service Cycles
Number of Service cycles (0~65535)
13
ItFC
Interval Token Cycles
Number of Token cycles (0~65535)
14
ACrC
Accumulated Regular Cycles
Number of Regular cycles ( 0~65535 )
15
ACCC
Accumulated Regular Cold Cycles
ACCC is not available in dryer. (It can’t enter.)
16
ACAC
Accumulated Regular Warm Cycles
ACAC is not available in dryer. (It can’t enter.)
17
ACHC
Accumulated Regular Hot Cycles
ACHC is not available in dryer. (It can’t enter.)
18
ACSC
Accumulated Super Cycles (Washer Only)
ACSC is not available in dryer. (It can’t enter.)
19
ACtF
Accumulated Topoff Cycles (Dryer Only)
Number of Topoff cycles ( 0~65535 )
20
ACUC
Accumulated Service Cycles
Number of Service cycles ( 0~65535 )
21
ACFC
Accumulated Token Cycles
Number of Token cycles (0~65535)
22
ACrt
Accumulated Run Time
Number of Running minutes ( 0~65535 )
42
PROGRAMMING MODE
■ Collect Mode Data lists
No.
Abbreviation
23
Itnr
Interval No Runs
Meaning
Itnr is not available in dryer.
Description
24
Ittb
Interval Trouble Cycles
Ittb is not available in dryer.
25
ItPd
Interval Power Downs
Number of power down
26
Itdd
Interval Unauthorized Service Door
Openings
Number of Unauthorized Service Door
Openings ( 0~ 255)
27
ItAd
Interval Authorized Service Door
Openings
Number of Unauthorized Service Door
Openings ( 0~ 255)
28
ItUC
Interval Unauthorized Coin Vault
Openings
Number of Authorized Service Door
Openings ( 0~ 255)
29
ItAC
Interval Authorized Coin Vault Openings
Number of Authorized Service Door
Openings ( 0~ 255)
30
tLdo
Time of Last Service Door Opening
tLdo is not available in dryer.(It can’t enter.)
31
tLCo
Time of Last Coin Vault Opening
tLCo is not available in dryer.(It can’t enter.)
32
tPdo
Time of Previous Service Door Opening
tPdo is not available in dryer.(It can’t enter.)
33
tPCo
Time of Previous Coin Vault Opening
tPCo is not available in dryer.(It can’t enter.)
34
SCPr
Super Cycle Price
Scpr is not available in dryer. (It can’t enter.)
35
toPr
Top Off Price
$0.00 ~ $10.00
36
Itd
Interval Money
Amount of money for regular cycle
($0 ~ $65535)
37
ACd
Accumulated Money
Amount of money for regular cycle
($0 ~ $65535)
38
Ittd
Interval Topoff Money
Amount of money for Topoff
($0 ~ $65535)
39
ACtd
Accumulated Topoff Money
Amount of money for Topoff
($0 ~ $65535)
INTERVAL means collecting since last data collection.
ACCUMULATED means collecting over a period of time since last factory reset (EEPt).
Authorized: Turning on/off the toggle switch with PDA Communication.
(Turning on/off the toggle switch within 30 minutes after Communicating with PDA)
Unauthorized: Turning on/off the toggle switch without PDA Communication.
These items (No.30~33) are not applied this program.
MAINTENANCE
43
MAINTENANCE
■ Regular cleaning
wWarning
Cleaning the Lint Filter
Always clean the lint filter after every cycle.
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
• Unplug the dryer before cleaning to avoid the risk
of electric shock. Failure to follow this warning can
cause serious injury, fire, electric shock, or death.
• Never use harsh chemicals, abrasive cleaners, or
solvents to clean the washer. They will damage the
finish.
Cleaning the Exterior
Proper care of your dryer can extend its life.
The outside of the machine can be cleaned with warm
water and a mild, nonabrasive household detergent.
Immediately wipe off any spills with a soft, damp cloth.
NOTE
Do not use methylated spirits, solvents, or similar
products.
Never use steel wool or abrasive cleansers; they can
damage the surface.
Lint Filter
To clean, open the dryer door and pull the lint filter
straight up.Then:
1. Roll any lint off the filter with your fingers, or
Cleaning the Interior
Wipe around the door opening and seal with a soft,
damp cloth to prevent lint and dust buildup that could
damage the door seal.
Clean the window with a soft cloth dampened with
warm water and a mild, nonabrasive household
detergent; then wipe dry.
The stainless steel drum can be cleaned with a
conventional stainless steel cleaner, used according to
the manufacturer’s specifications.
Never use steel wool or abrasive cleansers; they can
scratch or damage the surface.
2. Vacuum the lint filter, or
Cleaning Around and Under the Dryer
Vacuum lint and dust from around the dryer and
underneath it regularly. Vent ductwork should be
checked for lint buildup and cleaned at least once per
year. If any noticeable reduction in airflow or drying
performance occurs, immediately check ductwork for
obstructions and blockages.
3. If the lint filter has become very dirty or clogged with
fabric softener, wash the lint filter in warm, soapy
water and allow to dry thoroughly before reinstalling.
Maintaining Ductwork
Vent ductwork should be checked for lint buildup
and cleaned at least once per year. If any noticeable
reduction in airflow or drying performance occurs,
immediately check ductwork for obstructions and
blockages. Contact a qualified technician or service
provider.
NOTE
NEVER operate the dryer without the lint filter in
place. NEVER operate the dryer with a wet lint filter.
44
STACK MACHINE INSTALLATION INSTRUCTIONS
STACK MACHINE INSTALLATION INSTRUCTIONS
1. SUITABLE MODEL FOR STACKING
Stack type
Model Name
Upper Dryer
Lower Dryer
Lower Washer
RN1329AD5S/RV1329AD5S
RN1329AD6S/RV1329AD6S
F1069FD6/F1069FD6P
RN1329AN7S/RV1329AN7S
RN1329AN1S/RV1329AN1S
F1069FD/F1069FDP
RN1329A7S/RV1329A7S
RN1329A1S/RV1329A1S
F1069FD2/F1069FD2P
2. S
TACKING KIT
- STACKING KIT is provided in the upper dryer.
- STACKING KIT includes the stacking bracket(1), security bracket(3), bolt(1), screw(9).
1) Stacking bracket
2) bolt
3) Screw
4) security bracket
- SLIDING KIT includes the slide bracket(2), sliding pad(4), screw(18).
1) Stacking bracket
2) Sliding pad
NOTE
- The machine can be stacked only on the model designated as suitable by LGE.
- Do not stack the washer on the top.
- You can order the parts for stacking from Qualified dealer or Qualified SVS agent of LGE.
3) Screw
STACK MACHINE INSTALLATION INSTRUCTIONS
45
3. S
tacking the machine
- Install two sliding brackets on the top plate of lower washer.
- Remove the legs from the leg brackets.
- Remove the four(4) leg brackets from the bottom of upper dryer.
- Assemble the four(4) slide pads on the base.
*Security bracket installation (Only coin model)
- Install two security bracket on the panel frame and top plate in the lower
washer.
- Install one security bracket on the lower panel frame in the upper dryer.
- Lift and stack the upper dryer on the lower washer.
- Set the rear of the upper dryer and the rear of the lower washer in the same position.
- Push the upper dryer matching the slide & stacking bracket to make upper and lower front parallel.
- Install the stacking bracket at the rear of the stacked dryer and washer.
- Assemble the six(6) screw to fix the lower machine and upper dryer.
NOTE
Please refer to Service Manual for detail to explain how to stack and fix the machine
46
ERROR MODE / POWER FAIL RECOVERY / DEFAULT DRYER SETTINGS
ERROR MODE
■M
eaning of Error Codes that LED displays during occurrence or
problem.
Dryer error code
PROBLEM
POSSIBLE CAUSE
SOLUTION
It is displayed when thermistor is opened or
shorted
Thermistor should be replaced.
It is displayed when thermistor temperature
have increased about 17 degrees for 10 seconds
Thermistor should be replaced.
Disconnection of card reader wire.
Check the card reader wire.
POWER FAIL RECOVERY
In case of power failure the machine stops running but the time display remains on, showing the time just before
power failure.
Press the Start button after the power is restored, then the machine will restart.
DEFAULT DRYER SETTINGS
Default Settings
Default
Cycle Time (Minutes)
45 Minutes
Cool Down Time Cycle
2 Minutes
High Temperature
154.4° F (68° C)
Medium Temperature
140° F (60° C)
Low Temperature
125.6° F (52.5° C)
Top Off Time (Minutes per coin)
15 Minutes
Coin #1 Value
$1.00
Coin #2 Value
$1.00
Minutes/Minutes and seconds
Minutes
Fahrenheit/Celsius
Fahrenheit
Error Mode
On
47
Download PDF

advertising