advertisement
▼
Scroll to page 2
of 167
ENGLISH OWNER’S MANUAL LCD TV Please read this manual carefully before operating your set and retain it for future reference. www.lg.com Wall Mounting Bracket(Separate purchase) RW120 RW230 (22LD3***) (26/32LD3***) AW-47LG30M (32/37LD3***) HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Contents PREPARATION LCD TV MODELS : 22/26/32/37LD3***........... A-1 Antenna Connection.............................................1 Connecting with a Component cable...................2 Connecting with an HDMI cable..........................3 Speaker output Setup..........................................3 Connecting with an HDMI to DVI cable...............4 Connecting with a Euro Scart cable....................5 Usb setup.............................................................6 Connecting with a RF Cable................................6 Connecting with a D-sub 15 pin cable.................7 Insertion of CI Module..........................................8 Digital audio out Setup.........................................9 Headphone Setup................................................9 Supported Display Resolution............................10 Screen Setup for PC mode................................11 Watching TV / Programme control Turning on the TV..............................................15 Initializing Setup ................................................15 Programme Selection.........................................15 Volume Adjustment............................................15 Quick Menu........................................................16 On Screen Menus Selection and adjustment....17 Auto programme tuning ....................................18 Manual programme Tuning................................20 Programme Edit ................................................28 CI [Common Interface] Information....................32 Selecting the Programme List............................33 Input List.............................................................35 Input Label.........................................................36 Data Service.......................................................37 SIMPLINK...........................................................38 AV Mode.............................................................42 Initializing(Reset to original factory settings).....43 When connecting a USB device........................44 Movie list ...........................................................46 Photo list.............................................................57 Music list.............................................................67 Extra contents....................................................75 DivX Registration Code ....................................76 Deactivation ......................................................77 CONTENTS External equipment setup To use a USB device EPG(Electronic programme guide)(in digital mode) Switch on/off EPG..............................................79 Select a programme...........................................79 Button Function in NOW/NEXT Guide Mode....80 Button Function in 8 Day Guide Mode..............81 Button Function in Date Change Mode.............82 Button Function in Extended Description Box...83 Picture Control Picture Size (Aspect Ratio) Control...................84 Energy Saving....................................................86 Preset Picture Settings......................................88 Manual Picture Adjustment................................89 Picture Improvement Technology.......................90 Expert Picture Control........................................91 Picture Reset......................................................94 Power Indicator .................................................95 DEMO MODE.....................................................95 I CONTENTS Sound & Language control CONTENTS Auto Volume Leveler..........................................96 Clear Voice II......................................................97 Preset Sound Settings-Sound Mode.................98 Sound Setting Adjustment -User Mode.............99 Infinite Sound...................................................100 Balance............................................................101 DTV Audio Setting (in digital mode only).........102 Selecting Digital Audio out...............................103 Audio Reset......................................................104 Audio Description (In digital mode only)..........105 I/II Stereo/Dual Reception (In Analogue Mode Only). 106 NICAM Reception (In Analogue Mode Only)...107 Speaker Sound Output Selection....................107 On-Screen Menu Language / Country Selection... 108 Language Selection.........................................109 Time Setting Clock Setup...................................................... 111 Auto on/off time setting....................................112 Sleep Timer setting..........................................113 Alarm Setting....................................................113 Parental Control / Ratings Set Password & Lock System.........................114 Block Programme.............................................115 Parental Control (In Digital Mode only)............116 External Input Blocking....................................117 Key Lock..........................................................118 II Teletext Switch on/off ...................................................119 SIMPLE Text....................................................119 TOP Text..........................................................120 Fastext..............................................................120 Special Teletext Functions...............................121 Digital Teletext Teletext within Digital Service..........................122 Teletext in Digital Service.................................122 Appendix Troubleshooting................................................123 Maintenance.....................................................125 Product Specifications......................................126 IR Codes..........................................................127 External Control Device Setup.........................128 Open source software notice...........................135 PREPARATION LCD TV MODELS : 22/26/32/37LD3*** Accessories EN ER GY SAVI NG 7 0 MU ID E TE PO RT AL This item is not included for all models. MO DE T 9 6 TV RA / D 3 * Lightly wipe any stains or fingerprints on the surface of the TV with the polishing cloth. Q.V MA RAT IO GU AV INPU 2 5 8 LIS T 1 4 IEW RK P E G A P IN FO OK ME NU BA CK EX IT Polishing Cloth Polishing cloth for Do not use excessive force. This may cause scratching use on the or discolouration. screen. Q.M EN U AD AL GU AR ID M E PO RT AL Remote Control Owner’s Manual OK IN FO ME NU BA CK preparation Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. ■■ Image shown may differ from your TV. EX IT This item is not included for all models. Power Cord Batteries Ferrite Core (This item is not included for all models.) VELCRO (LOOP) VELCRO (HOOK) HOLDER CABLE x4 (Only 22LD3***,) Cable management clip (Only 26/32/37LD3***) 1-screw for stand fixing (Only 26/32/37LD3***) Bolts for stand assembly or Protection Cover (Only 26/32/37LD3***) Protective Bracket and Bolt for Power Cord Use of ferrite core (This feature is not available for all models.) Ferrite core can be used to reduce the electromagnetic wave when connecting the power cord. The closer the location of the ferrite core to the power plug, the better it is. Install the power plug closely. A-1 preparation Front panel controls NOTE preparation ►TV ► can be placed in standby mode in order to reduce the power consumption. And TV should be switched off using the power switch on the TV if it will not be watched for some time, as this will reduce energy consumption. ►The ► energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost. ■■ Image shown may differ from your TV. (Only 22/26LD3***) POWERINPUT MENU OK VOLUME PROGRAMME CH INPUT MENU OK P (Only 32/37LD3***) PROGRAMME VOL VOLUME OK MENU Remote Control Sensor ENTER INPUT POWER MENU INPUT A-2 Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. POWER Back Panel Information ■■ Image shown may differ from your TV. 22LD3*** 2 3 4 preparation 12 1 5 13 H/P 6 1 2 7 8 9 10 Power Cord Socket This TV operates on an AC power. The voltUSB IN age is indicated on the Specifications page. (► p.126) Never attempt to operate the TV on DC power. USB Input / DVI IN Connect USB storage device to HDMI this jack. 3 RGB/DVI Audio Input Connect the audio from a PC or DTV. 4 OPTICAL DIGITAL AUDIO OUT Connect digital audio to various types of equipment. Connect to a Digital Audio Component. Use an Optical audio cable. 7 COMPONENT IN Euro Scart Socket (AV) Connect scart socket input or output from an external device to these jacks. 6 HDMI/DVI IN Input Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode. (RGB) RJP INTERFACE 8 RGB IN Input Connect the output from a PC. 9 Component Input SPEAKER OUT ANTENNA IN Connect a component video/audio device to these jacks. 10 SPEAKER OUTPUT(STEREO) The phone socket for external speaker is on this jack. 11 Antenna Input Connect antenna or cable to this jack. 12 PCMCIA (Personal Computer Memory Card International Association) Card Slot Insert the CI Module to PCMCIA CARD SLOT. (This feature is not available in all countries.) 13 Headphone Socket Plug the headphone into the headphone socket. RGB IN (PC) 5 11 VOLUME CONTROL STEREO (8 ) A-3 preparation 26/32/37LD3*** preparation 11 1 12 2 3 4 5 (RGB) VOLUME CONTROL 2 /DVI IN STEREO (8 ) 1 SPEAKER OUT 6 7 13 ANTENNA IN 8 H/P 9 10 7 RGB IN Input Connect the output from a PC. 8 HDMI/DVI IN Input Connect an HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable. Component Input Connect a component video/audio device to these jacks. 9 SPEAKER OUTPUT(STEREO) The phone socket for external speaker is on this jack. 3 RGB/DVI Audio Input Connect the audio from a PC or DTV. 10 Antenna Input Connect antenna or cable to this jack. 4 OPTICAL DIGITAL AUDIO OUT Connect digital audio to various types of equipment. Connect to a Digital Audio Component. Use an Optical audio cable. 11 USB Input Connect USB storage device to this jack. 12 PCMCIA (Personal Computer Memory Card International Association) Card Slot Insert the CI Module to PCMCIA CARD SLOT. (This feature is not available in all countries.) 13 Headphone Socket Plug the headphone into the headphone socket. 1 2 A-4 RJP INTERFACE Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. (► p.126) Never attempt to operate the TV on DC power. 5 Euro Scart Socket (AV) Connect scart socket input or output from an external device to these jacks. 6 RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode. Stand installation ■■ Image shown may differ from your TV When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. Only 26/32/37LD3*** 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the TV as shown. 2 Assemble the TV as shown. 3 Fix the 4 bolts securely using the holes in the back of the TV. preparation Only 22LD3*** A-5 preparation Back Cover for Wire Arrangement ■■ Image shown may differ from your TV. 22LD3*** preparation 1 2 26/32/37LD3*** Connect the cables as necessary. To connect additional equipment, see the External equipment setup section. 1 2 Install the Cable Management clip as shown. Connect the cables as necessary. To connect additional equipment, see the External equipment setup section. pen the Cable Management clip as O shown. Cable management clip Cable management clip 3 3 Fit the Cable Management clip as shown. Fit the Cable Management clip as shown. How to remove the cable management clip (22LD3***) Hold the Cable Management clip with both hands and pull it backward. NOTE ►Do ► not use the Cable Management Clip to lift the TV. -If the TV is dropped, you may be injured or the TV may be damaged. A-6 Not using the desk-type stand ■■ Image shown may differ from your TV. When installing the wall-mounted unit, use the protection cover. 22LD3*** Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Insert the Protection cover into the TV until clicking sound. 2 Loose the bolts from TV. 3 Detach the stand from TV. 4 Insert the Protection Cover into the TV. preparation 1 26/32/37LD3*** protection cover protection cover 5 Fix the 4 bolts securely using the holes in the back of the TV. A-7 preparation Attaching the TV to a desk (Only 26/32/37LD3***) preparation ■■ Image shown may differ from your TV. The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. 4-Screws (not provided as parts of the product) ► Screw: M5 x L (*L: Table depth + 8~10 mm) ex) Table depth: 15mm, Screw: M5 x 25 Swivel Stand ■■ Image shown may differ from your TV. After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position. How to secure the power cable (Only 26/32/37LD3****) Secure the power cable with the Protective Bracket and the bolt as shown. It will help prevent the power cable from being removed by accident. Stand Bolt Desk Protective Bracket 1-Screw (provided as parts of the product) Stand Positioning your display (Only 22LD3***) ■■ Image shown may differ from your TV. ■■ Adjust the position of the panel in various ways for maximum comfort. • Tilt range 12 Desk WARNING A-8 ►To ► prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury. 0 0 3 Kensington Security System ■■ This feature is not available for all models. ■■ Image shown may differ from your TV. NOTE ►►The Kensington Security System is an optional accessory. ►►If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV. ►►Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. ►►Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. ■■ You should purchase necessary components to fix the TV safety and secure to the wall on the market. ■■ Position the TV close to the wall to avoid the possibility of it falling when pushed. ■■ The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV. preparation he TV is equipped with a Kensington Security T System connector on the back panel. Connect the Kensington Security System cable as shown below. For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System. For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors. Careful installation advice 1 1 22 2 1 Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen then bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. 2 Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall. 3 3 Use a sturdy rope to tie the product for alignment. It is safer to tie the rope so it becomes horizontal between the wall and the product. NOTE ►When ► moving the TV undo the cords first. ►Use ► a platform or cabinet strong and large enough to support the size and weight of the TV. ►To ► use the TV safely make sure that the height of the bracket on the wall and on the TV is the same. A-9 preparation ■■ The TV can be installed in various ways such as on a wall, or on a desktop etc. ■■ The TV is designed to be mounted horizontally. Earthing preparation Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes. Power Supply Circuit breaker Desktop Pedestal Installation NOTE ►►Should Install wall mount on a solid wall perpendicular to the floor. ►►Should use a special wall mount, if you want to install it to ceiling or slanted wall. ►►The surface that wall mount is to be mounted on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block. ►►Installing screw type and length depends on the wall mount used. Further information, refer to the instructions included with the mount. ►►LG is not liable for any accidents or damage to property or TV due to incorrect installation: - Where a non-compliant VESA wall mount is used. - Incorrect fastening of screws to surface which may cause TV to fall and cause personal injury. - Not following the recommended Installation method. 10 cm 10 cm ■■ Image shown may differ from your TV. 10 cm 10 cm For adequate ventilation allow a clearance of 10 cm all around the TV. 10 cm 10 cm 10 cm 10 cm 10 cm Wall Mount: Horizontal installation ■■ We recommend the use of a LG Brand wall mounting bracket when mounting the TV to a wall. ■■ We recommend that you purchase a wall mounting bracket which supports VESA standard. ■■ LG recommends that wall mounting be performed by a qualified professional installer. A-10 B Model 22LD3*** 26/32LD3*** 37LD3*** A A B VESA Standard Quantity (A * B) Screw 100 * 100 M4 4 200 * 100 M4 4 200 * 200 M6 4 Remote Control Key Functions When using the remote control, aim it at the remote control sensor on the TV. (POWER) Switches the TV on from standby or off to standby. ENERGY AV MODE AV MODE It helps you select and set images and sounds when connecting AV devices.(► p.42) INPUT TV/ RAD SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW INPUT External input mode rotate in regular sequence.(► p.36) TV/RAD Selects Radio, TV and DTV channel. 0 to 9 number Selects a programme. button Selects numbered items in a menu. LIST Displays the programme table. (► p.33) Q.VIEW Returns to the previously viewed programme. GUIDE Shows programme guide(► p.78) MARK RATIO preparation ENERGY Adjust the Energy Saving mode of the TV.(► p.86) SAVING P PORTAL Displays and removes hotel interactive menu. P A G E INFO i Shows the present screen information. MUTE GUIDE PORTAL INFO THUMBSTICK Allows you to navigate the on-screen menus and to your preference. (Up/Down/Left/Right) adjust the system settings GUIDE PORTAL INFO OK Accepts your selection or displays the current mode. OK MENU Selects a menu. Clears all on-screen displays and returns to TV viewing from any menu.(► p.17) OK MENU BACK BACK Allows the user to move return one step in an interactive application, EPG or other user interaction function. EXIT MENU BACK EXIT EXIT Clears all on-screen displays and returns to TV viewing from any menu. 1 Coloured These buttons are used for teletext (on TELETEXT buttons models only), Programme edit. Q.MENU AD ALARM 1 TELETEXT These buttons are used for teletext. BUTTONS For further details, see the ‘Teletext’ section.(► p119) SUBTITLE Recalls your preferred subtitle in digital mode. A-11 preparation VOLUME UP Adjusts the volume. /DOWN preparation ENERGY AV MODE MARK Check and un-check programmes in the USB menu. INPUT TV/ RAD RATIO Selects your desired Aspect Ratio of picture.(► p.84) SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW MUTE Switches the sound on or off. Programme Selects a programme. UP/DOWN PAGE UP/ Move from one full set of screen information to the DOWN next one. MARK RATIO P MUTE GUIDE PORTAL INFO OK P A G E SIMPLINK / Controls SIMPLINK or MY MEDIA menu(Photo List, MY MEDIA Menu Music List, Movie List and Extra contents). control buttons See a list of AV devices connected to TV. When you toggle this button, the Simplink menu appears at the screen.(► p.38) INFO PORTAL GUIDE Q. MENU Select the desired quick menu source. (Aspect Ratio, Clear Voice II , Picture Mode, Sound Mode, Audio (or Audio Language), Sleep Timer, Skip Off/On, USB Device).(► p.16) OK AD Switches the Audio Description On or Off.(► p.105) ALARM Sets the alarm function.(► p.113) A-12 MENU BACK Q.MENU AD EXIT Installing Batteries ALARM MENU BACK EXIT ■■ Open the battery compartment cover on the back and install the batteries matching correct polarity (+with +,-with -). ■■ Install two 1.5 V AAA batteries. Do not mix old or used batteries with new ones. ■■ Close cover. ■■ To remove the batteries, perform the installation actions in reverse. External equipment setup ■■ To prevent damage do not connect to the mains outlet until all connections are made between the devices. Antenna Connection ■■ For optimum picture quality, adjust antenna direction. ■■ An antenna cable and converter are not supplied. Multi-family Dwellings/Apartments (Connect to wall antenna socket) RS-232C IN (CONTROL) HDMI/DVI IN USB IN SERVICE ONLY RGB IN (PC) AUDIO IN (RGB/DVI) VIDEO VIDEO COMPONENT IN AUDIO L(MONO) AUDIO R IN ANTENNA IN OUT VARIABLE AUDIO OUT AV IN RS-232C IN (CONTROL) HDMI USB IN SERVICE ONLY 2 RGB IN (PC) HDMI 1 /DVI IN IN 3 Outdoor Antenna (VHF, UHF) RF Coaxial Wire (75 Ω) AUDIO IN (RGB/DVI) 1 VIDEO VIDEO COMPONENT IN AUDIO L(MONO) AUDIO R IN1 OUT VARIABLE AUDIO OUT Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) ANTENNA IN AV external equipment setup Wall Antenna Socket AV IN2 VIDEO USB IN SERVICE ONLY AV IN RGB IN (PC) AUDIO /DVI IN L(MONO) R AUDIO IN OPTICAL DIGITAL AUDIO OUT (RGB/DVI) 2 UHF Antenna VIDEO COMPONENT IN L R AUDIO 1 (DVI) ANTENNA/ RS-232C IN CABLE IN (CONTROL&SERVICE) Signal Amplifier VHF ■■ In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above. ■■ If signal needs to be split for two TVs,use an antenna signal splitter for connection. 1 external equipment setup ■■ To avoid damaging any equipment, never plug in any power cord until you have finished connecting all equipment. ■■ This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 32LD3*** models. ■■ Image shown may differ from your TV. Connecting with a Component cable This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below. external equipment setup 1 Connect the video outputs (Y, PB, PR) of the external equipment (digital set-top box, DVD, etc.) to the COMPONENT IN VIDEO jacks on the TV. (RGB) 1 VOLUME CONTROL 2 2 Connect the audio output of the external equipment (digital set-top box, DVD, etc.) to the COMPONENT IN AUDIO jacks on the TV. 3 Turn on the external equipment. (Refer to the external equipment's manual for operating instructions.) 4 Select the Component input source using the INPUT button on the remote control. /DVI IN STEREO (8 ) 1 2 SPEAKER OUT ►►HDMI Audio Supported format : Dolby Digital, PCM DTS Audio format is not supported. Signal Component HDMI 480i/576i 480p/576p 720p/1080i O O O X O O O 1080p O (50 Hz / 60 Hz only) (24 Hz / 30 Hz / 50 Hz / 60 Hz) Component Input ports To achieve better picture quality, connect a DVD player to the component input ports as shown below. 2 Component ports on the TV Y PB PR Video output ports on DVD player Y Y Y Y PB B-Y Cb Pb PR R-Y Cr Pr ANTENNA IN Connecting with an HDMI cable 1 Connect the HDMI output of the external equipment (digital settop box, DVD, etc.) to HDMI/DVI IN 1, HDMI 2 (Except for 22LD3***) jack on the TV. 2 Turn on the external equipment. (Refer to the external equipment's manual for operating instructions.) 2 /DVI IN 1 NOTE external equipment setup Select HDMI1, HDMI2 (Except for 22LD3***) input source using the INPUT button on the remote control. 3 1 ►►The TV can receive video and audio signals simultaneously when using an HDMI cable. ►►If the DVD does not support Auto HDMI, you must set the output resolution appropriately. ►►Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are not High Speed HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable. (RGB) Speaker output Setup 1 UP 2 Connect the external speaker to the Speaker output(STEREO) jack on the TV. 1 /DVI IN Control port for Speaker out VOLUME CONTROL DOWN 1 (8 ) SPEAKER OUT (RGB) Method of Volume control port Cable Spec. GND / Up / Down • Each Up/ Down pin is pulled to 3.3V with CPU GPIO. VOLUME CONTROL • CPU detects transition from 3.3V to GND level for volume control. SPEAKER OUT STEREO (8 ) 1 GND RIGHT LEFT GND 3 external equipment setup Connecting with an HDMI to DVI cable external equipment setup 4 1 Connect the digital set-top box or the DVI output of the PC to HDMI/DVI IN 1 jack on the TV. 2 Connect the audio output of the digital set-top box or the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV. 3 4 Turn on the digital set-top box or the PC and the TV. (Refer to the digital set-top box or the PC manual for operating instructions.) (RGB) VOLUME CONTROL 2 /DVI IN 1 (8 ) SPEAKER OUT 1 2 Select HDMI1 input source using the INPUT button on the remote control. or ANTENNA IN Connecting with a Euro Scart cable 1 Connect the Euro scart socket of the external equipment (DVD, VCR, etc.) to the AV Euro scart socket on the TV. 2 Turn on the external equipment. (Refer to the external equipment's manual for /DVI D IN operating instructions.) (RGB) Video Audio RGB Video, Audio AV O O O Analogue TV, Digital TV Current input model ANTENNA IN 1 Output Scart Output Type SPEAKER OUT AV (TV Out) Digital TV Digital TV Analogue TV, AV Analogue TV Component/RGB Analogue TV HDMI Analogue TV ►►TV Out : Outputs Analogue TV or Digital TV signals. external equipment setup Input STEREO (8 ) 1 Select AV input source using the INPUT button on the remote control. 3 VOLUME CONTROL 2 NOTE ►►Any Euro scart cable used must be signal shielded. 5 external equipment setup Usb setup 1 Connect the USB device to the USB IN jack on the TV. or 1 2 After connecting the USB IN jack, you use the USB function. (► p44) external equipment setup Connecting with a RF Cable To avoid picture noise (interference), allow adequate distance between the VCR and TV. 1 Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the TV. 2 onnect the antenna cable to the ANT IN C socket of the VCR. 3 Press the PLAY button on the VCR and match the appropriate channel between the TV and VCR for viewing. 1 2 Wall Jack Antenna 6 Connecting with a D-sub 15 pin cable This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. Connect the RGB output of the PC to the RGB IN (PC) jack on the TV. 2 Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV. 3 Turn on the PC and the TV 4 Select RGB input source using the INPUT button on the remote control. (RGB) VOLUME CONTROL 2 /DVI IN STEREO (8 ) 1 SPEAKER OUT 2 1 external equipment setup 1 (DVI) 7 ANTENNA IN USB IN external equipment setup Insertion of CI Module VIDEO L/MONO AUDIO R external equipment setup 8 Insert the CI Module to PCMCIA (Personal Computer Memory Card International Association) CARD SLOT of TV as shown. USB IN 1 H/P HDMI IN 2 To view the encrypted (pay) services in digital TV mode. This feature is not available in all countries. For further information, see p.32. AV IN 2 NOTE (RGB) Check this point as shown and insert the CI Module. ►►Check if the CI module is inserted into the PCMCIA card slot in the right direction. If the module is not inserted properly, this can cause damage to the TV and the PCMCIA card slot. 1 HDMI / DVI IN H/P ANTENNA IN Digital audio out Setup Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp). Connect one end of an optical cable to the TV Digital Audio (Optical) Output port. 2 Connect the other end of the optical cable to the digital audio (Optical) input on the audio equipment. (RGB) VOLUME CONTROL 2 /DVI IN 1 1 CAUTION ►►Do not look into the optical output port. Looking at the laser beam may damage your vision. external equipment setup 1 2 (8 ) SPEAKER OUT Headphone Setup You can listen the sound through the headphone. 1 Plug the headphone into the headphone socket. 2 To adjust the headphone volume, press the + or - button. If you press the MUTE button, the sound from the headphone is switched off. NOTE ►►AUDIO menu items are disabled when connecting a headphone. ►►When changing AV MODE with a headphone connected, the change is applied to video but not to audio. ►►Optical Digital Audio Out is not available when connecting a headphone. ►Headphone ► impedance: 16 Ω ►Max ► audio output of headphone: 10 mW to 15 mW 9 ANTENNA external equipment setup Supported Display Resolution RGB-PC, HDMI/DVI-PC mode HDMI/DVI-DTV mode external equipment setup Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 720x400 31.468 70.08 640x480 31.469 59.94 800x600 37.879 60.31 1024x768 48.363 60.00 1280x768 47.78 59.87 44.96/45 59.94/60 1360x768 47.72 59.8 33.72/33.75 59.94/60 1280x720 (RGB-PC) 45 60 28.125 50 26.97/27 23.97/24 33.716/33.75 29.976/30.00 56.25 50 67.43/67.5 59.94/60 1920x1080 (RGB-PC) 66.587 1920x1080 (HDMI-PC) 67.5 59.93 60.00 Resolution 720x480 720x576 1280x720 1920x1080 Horizontal Frequency(kHz) Vertical Frequency(Hz) 31.469 59.94 31.5 60 31.25 50 37.5 50 (Except for 22/26/32LD3***) NOTE 10 ►►Avoid keeping a fixed image on the set’s screen for prolonged periods of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible. ►►There may be interference relating to resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. ►►The synchronization input waveform for Horizontal and Vertical frequencies are separate. ►►We recommend using 1360x768, 60 Hz (only 22/26/32LD3***), 1920x1080,60 Hz (only 37LD3***) for the PC mode, this should provide the best picture quality. ►►Connect the signal cable from the monitor output port of the PC to the RGB (PC) port of the TV or the signal cable from the HDMI output port of the PC to the HDMI IN (or HDMI/DVI IN) port on the TV. ►►Connect the audio cable from the PC to the Audio input on the TV. (Audio cables are not included with the TV). ►►If using a sound card, adjust PC sound as required. ►►If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC output on the TV. ►►If the graphic card on the PC does output analogue and digital RGB simultaneously, set the TV to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the TV.) ►►DOS mode may not work depending on the video card if you use an HDMI to DVI cable. ►►If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of cable. This provides the best picture quality. Screen Setup for PC mode Screen Reset Returns Position, Size and Phase to the factory default settings. This function works in the following mode : RGB[PC]. Move SCREEN OK Prev. Resolution • Sharpness 70 • Colour 60 • Tint 0 R G • Colour Temp. 0 W C • Advanced Control • Picture Reset Auto Config. Position Size ► Screen •• Screen Move To Set Yes No Phase Reset 1 2 3 4 5 external equipment setup PICTURE Select PICTURE. Select Screen. Select Reset. Select Yes. Run Reset. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 11 external equipment setup Auto Configure (RGB [PC] mode only) Automatically adjusts the picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. PICTURE Move SCREEN OK Resolution • Sharpness 70 • Colour 60 • Tint 0 R G • Colour Temp. 0 W C • Advanced Control Screen •• Screen Auto Config. Position Size • Picture Reset Prev. Move Auto Config. Yes No ► external equipment setup Auto configure This function is for automatic adjustment of the screen position, size, and phase The displayed image will be unstable for a few seconds while the auto configuration is in progress. Phase Reset 1 2 3 4 5 Select PICTURE. Select Screen. • If the position of the image is still not correct, try Auto adjustment again. • If picture needs to be adjusted again after Auto adjustment in RGB (PC), you can adjust the Position, Size or Phase. Select Auto Config.. Select Yes. Run Auto Config.. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 12 Selecting Resolution To view a normal picture, match the resolution of RGB mode and selection of PC mode. This function works in the following mode: RGB[PC] Move SCREEN OK Resolution • Sharpness 70 • Colour 60 • Tint 0 R G • Colour Temp. 0 W C • Advanced Control • Picture Reset Position Prev. 1024 x 768 1280 x 768 1360 x 768 Size ► Screen •• Screen Auto Config. Move Phase Reset 1 2 3 4 external equipment setup PICTURE Select PICTURE. Select Screen. Select Resolution. Select the desired resolution. 5 • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 13 external equipment setup Adjustment for screen Position, Size, Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture position manually. This function works in the following mode : RGB[PC]. external equipment setup PICTURE Move SCREEN OK Prev. Resolution • Sharpness 70 • Colour 60 • Tint 0 R G • Colour Temp. 0 W C • Advanced Control • Picture Reset Auto Config. Position Size ► Screen •• Screen Move Phase Reset 1 2 3 4 Select PICTURE. Select Screen. Select Position, Size or Phase. Make appropriate adjustments. 5 • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 14 Watching TV / Programme control Turning on the TV When your TV is turned on, you will be able to use its features. 1 Firstly, connect the power cord correctly. At this stage, the TV switches to standby mode. 2 In standby mode to turn TV on, press the / I, INPUT or P (or P ▲▼ ) button on the TV or press the POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on. 1 If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the Language, Power Indicator, Country or TimeZone (When Russia is selected for Country) or Set Password(When France is selected for Country), Auto Tuning. Note: a.If you close without completing the initial setting, the Initial Setting menu can be displayed again. b.Press the BACK button to change the current OSD to the previous OSD. c.For those countries without confirmed DTV broadcasting standards, some DTV features might not work, depending on the DTV broadcasting environment. d. When France is selected for Country, password is not '0', '0', '0', '0' but ‘1’, ‘2’, ‘3’, ‘4’. Programme Selection 1 Press the P Watching TV / Programme control Initializing Setup or NUMBER buttons to select a programme number. Volume Adjustment + or - button to adjust the volume. 1 Press the 2 If you wish to switch the sound off, press the MUTE button. You can cancel this function by pressing the MUTE, + -, I/II, or AV Mode button. 15 Watching TV / Programme control Quick Menu Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. Watching TV / Programme control Aspect Ratio: Selects your desired picture format. For Zoom Setting, select 14:9, Zoom and Cinema Zoom in Ratio Menu. After completing Zoom Setting, the display goes back to Q.Menu. Clear Voice II : By differentiating the human sound range from others, it helps users listen to human voices better. Picture Mode : Selects your desired Picture Mode. Sound Mode : It is a feature to automatically set the sound combination which it deems the best for the images being watched. Selects your desired Sound Mode. ◄ Aspect Ratio Audio or Audio Language : Selects the sound output. Sleep Timer : Sets the sleep timer. Skip Off/On : Selects the Skip Off/On. USB Device : Selects “Eject” in order to eject USB device. ► 16:9 Exit 1 2 3 16 Display each menu. Select your desired Source. • Press the Q.MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. On Screen Menus Selection and adjustment Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. SETUP ● Auto Move Tuning ● Manual ● Aspect Tuning ● Programme ● CI ● Edit Information ● Auto : 16:9 Mode ● Lock Volume ● Clear ● Sound System Mode ● Parental ● Input Lock • Contrast 100 • Infinite Sound : Off • Brightness 50 • Treble 50 • Sharpness 70 • Bass 50 • Colour 70 • Reset TIME SETUP Programme PICTURE AUDIO TIME Guidance: Blocking Off Move Mode ● Country OK INPUT OPTION Input List Move OK : UK : Off Time : Off Timer : Off : Off MY MEDIA MY MEDIA Antenna USB AV Component RGB HDMI1 Movie List Indicator Time ● On OK ● Disability Assistance Photo List Music List Extra Contents HDMI2 Reset Press OK( :1 Input Label 1 Move ● Alarm : Off ● Language(Language) ID R ● Off ● Sleep Block OPTION ● Set L 70 : Off ● Factory 0 : Standard • Backlight : Off ● Power 3 ● Clock ● Block ● Demo : Off OK OK : Off Voice II ● Balance : Standard LOCK Exit ) to see photos from the USB. Option Exit Display each menu. 2 3 Move Password ● Key Ratio AUDIO OK Watching TV / Programme control Move Move Energy Saving : Off ● Picture LOCK ● Set PICTURE OK Select a menu item. Move to the pop up menu. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. NOTE ►►It is not possible to use CI Information in Analogue mode. 17 Watching TV / Programme control Auto programme tuning Use this to automatically find and store all available programmes. When you start auto programming, all previously stored service information will be deleted. The maximum number of programmes that can be stored is 500. But the number may differ slightly depending on broadcasting signals. Move ● Auto Auto Tuning Tuning ● ● Manual Tuning ● Programme ● CI SETUP OK ► Watching TV / Programme control SETUP Edit Information Move ● Auto Tuning ● Auto Tuning ● Manual Tuning ● Programme ● CI OK Antenna Edit Antenna Information Check your antenna connection. The previous channel information will be updated during Auto Tuning. SECAM L Search Start Close 1 2 3 4 Select SETUP. Select Auto Tuning. Select Start. Run Auto tuning. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 18 • Use NUMBER buttons to input a 4-digit password in Lock System ‘On’. • If you wish to keep on auto tuning select Start using the button. Then, press the OK button. Otherwise select Close. • When select Italy in the County menu, If the pop up is displayed when the conflicted programme after Auto Tuning, select a broadcaster for Conflicting programme number to solve. Watching TV / Programme control 19 Watching TV / Programme control Manual programme Tuning (In Digital Mode) Manual Tuning lets you manually add a programme to your programme list. If you want to select the DTV, SETUP Move ● Auto ● Programme Move ◄ Tuning ● Manual Tuning ► ● Manual Tuning ● CI SETUP OK Tuning ► Watching TV / Programme control ● Auto Edit ● Programme Information ● CI Edit OK ► DTV UHF CH. 30 Frequency(kHz) 474000 Information ● Signal Strength ● Signal Quality 50% 50% Add Close 1 2 3 4 5 Select SETUP. Select Manual Tuning. Select DTV. Select the desired channel number. Select update or add if signal present. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 20 •U se NUMBER buttons to input a 4-digit password in Lock System ‘On’. • You can select SBAND when the country is set to "Norway, Latvia." Watching TV / Programme control 21 Watching TV / Programme control If you want to select the Cable DTV, SETUP Tuning ● Auto ● Programme ► ● Manual Tuning ● CI SETUP OK ► Watching TV / Programme control ● Auto Move Edit Information Move ◄ OK Cable DTV Frequency(kHz) Tuning ● Manual Tuning Symbol rate(kS/s) ● Programme Modulation ● CI Edit Information ► 362000 6875 64QAM ● Signal Strength ● Signal Quality 50% 50% Add Close 1 2 3 4 Select SETUP. Select Manual Tuning. Select Cable DTV. Make appropriate adjustments. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 22 • Use NUMBER buttons to input a 4-digit password in Lock System ‘On’. • Symbol rate : Enter a user-defined symbol rate (Symbol rate: Speed at which a device such as modem sends symbols to a channel). • Modulation : Enter a user-defined modulation. (Modulation: Loading of audio or video signals onto carrier). Watching TV / Programme control 23 Watching TV / Programme control Manual programme Tuning (In Analogue Mode) Manual Tuning lets you manually tune and arrange the stations in whatever order you desire. SETUP ● Auto Move ● Auto Move Edit ● Programme Watching TV / Programme control Information ● CI OK Tuning ◄ ● Manual Tuning ► ● Programme ► ● Manual Tuning ● CI SETUP OK Tuning Edit Information ► TV ● Storage ● System ● Band ● Storage BG ● System V/UHF ● Channel 0 ● Fine ● Search ● Name ◄ 3 or ◄► ● Search Store 2 3 4 5 6 Select SETUP. Select Manual Tuning. 7 8 Select TV or Cable TV. or Select the desired programme number on. 9 0 ◄► ◄► ● Name C 02 Store Close 1 BG V/UHF ● Channel ● Fine ► 3 ● Band ◄► C 02 Cable TV Close Select V/UHF or Cable. or Select the desired channel number. Commence searching. Select Store. Select a TV system. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 24 •Use NUMBER buttons to input a 4-digit password in Lock System ‘On’. •L : SECAM L/L’ (France) BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa) I : PAL I (U.K. / Ireland / Hong Kong / South Africa) DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS) •To store another channel, repeat steps 4 to 9. Watching TV / Programme control 25 Watching TV / Programme control SETUP Tuning ● Auto ● Programme ► ● Manual Tuning ● CI SETUP OK ► ● Auto Move Edit ● CI OK Tuning ◄ ● Manual Tuning ● Programme Information Move Edit Information ► TV ◄ ● Storage 3 ● Storage ● System BG ● System ● Band V/UHF ● Channel or 0 Cable TV ► 3 BG ● Band V/UHF ● Channel 0 ● Fine ◄► ● Fine ◄► ● Search ◄► ● Search ◄► ● Name C 02 ● Name C 02 Store Store Close Close Watching TV / Programme control ■■Assigning a station name You can assign a station name with five characters to each programme number. 1 2 3 4 Select SETUP. 5 Select Manual Tuning. Select TV or Cable TV. 6 Select Name. 7 Select the position and make your choice of the second character, and so on. You can use an the alphabet A to Z, the number 0 to 9, +/ -, and blank. Select Close. Select Store. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 26 SETUP ● Auto Move Tuning ● Auto ► ● Programme ► ● Manual Tuning ● CI SETUP OK Edit ● CI OK Tuning ◄ ● Manual Tuning ● Programme Information Move Edit Information ► TV ◄ ● Storage 3 ● Storage ● System BG ● System ● Band V/UHF ● Channel or 0 Cable TV ► 3 BG ● Band V/UHF ● Channel 0 ● Fine ◄► ● Fine ◄► ● Search ◄► ● Search ◄► ● Name C 02 ● Name C 02 Store Store Close Close Normally fine tuning is only necessary if reception is poor. 1 2 3 Select SETUP. 4 Select Manual Tuning. 5 Select TV or Cable TV. 6 Select Fine. Fine tune for the best picture and sound. Select Store. Watching TV / Programme control ■■Fine Tuning • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 27 Watching TV / Programme control Programme Edit When a programme number is skipped, it means that you will be unable to select it using P during TV viewing. button If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the Programme edit menu. This function enables you to skip the stored programmes. Page 1/2 TV SETUP Tuning ● Manual Tuning Programme Edit ●●Manual Tuning Programme Edit ● CI OK ► ● Auto Move ► Watching TV / Programme control Programme Edit Information 1 YLE TV1 (D) 2 YLE TV2 (D) 3 YLE FST (D) 4 YLE24 (D) 5 YLE Teema (D) 6 YLE PEILI (R) 7 YLEQ (R) 8 YLEN KLASSINEN (R) 9 YLE FSR+ 10 YLEMONDO (R) 11 YLE X3M (R) 12 TV4 Stockholm 13 Kanal Lokal (D) 14 CNN (D) 15 TV4 (D) 15 TV4 Plus (D) 17 TV400 (D) 18 TV4 Film (D) 19 TV4 Fakta (D) 20 MediaCorp HD5 (D) 21 Dolby D 5.1 Demo (R) D: Digital TV (R) R: Digital Radio (D) A: Analogue TV ▼ Pr. Change Delete 1 2 3 4 Previous Move Block/Unblock Skip Select SETUP. Select Programme Edit. Enter the Programme Edit. Select a programme to be stored or skipped. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 28 ■■Skipping a programme number 1 Select a programme number to be skipped. 2 BLUE Turn the programme number to blue. 3 BLUE Release. • When programmes are to be skipped, the skipped programme shows in blue and these programmes will not be selected by the P buttons during TV viewing. • If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG. Watching TV / Programme control 29 Watching TV / Programme control This function enables you to delete or skip the stored programmes. You can also move some channels and use other programme numbers. ■■Locking a programme number 1 Select a programme number to be locked. 2 • It can be registered as Lock programme even when Lock System is turned Off. YELLOW Turn the programme number to yellow. 3 YELLOW Release. Watching TV / Programme control 30 ■■Deleting a programme 1 2 RED Select a programme number to be deleted. •T he selected programme is deleted, all the following programmes are shifted up one Turn the programme number to red. ■■Moving a programme 1 2 GREEN Select a programme number to be moved. Turn the programme number to green. 3 GREEN Release. Watching TV / Programme control 31 Watching TV / Programme control CI [Common Interface] Information This function enables you to watch some encrypted services (pay services). If you remove the CI Module, you cannot watch pay services. When the module is inserted into the CI slot, you can access the module menu. To purchase a module and smart card, contact your dealer. Do not repeatedly insert or remove a CI module from the TV. This may cause a malfunction. When the TV is turned on after inserting a CI Module, you may not have any sound output. This may be incompatible with the CI module and smart card. CI (Common Interface) functions may not be possible depending upon the country broadcasting circumstances. SETUP ● Auto Move i OK Tuning ● Manual Authorizations Tuning ● Programme Module information Edit ● CI Information Viaccess Module Consultations ► Watching TV / Programme control When using a CAM(Conditional Access Module), please make sure it meets fully the requirements of either DVB-CI or CI plus. Select the item • This OSD is only for illustration and the menu options and screen format will vary according to the Digital pay services provider. • It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer. 1 Select SETUP. 2 Select CI Information. 3 4 Select the desired item: Module information, smart card information, language, or software download etc. Save. • Press the BACK/EXIT button to move to the previous menu screen. 32 Selecting the Programme List You can check which programmes are stored in the memory by displaying the programme list. Mini Glossary Exit 1 BBC ► Displayed when the Locked Programme. Programme List 2 BBC 3 BBC 4 BBC 5 BBC A ■■Displaying programme LIST 1 Display the Programme List. •Y ou may find some blue programmes. These have been set up to be skipped by auto programming or in the programme edit mode. •S ome programmes with the channel number shown in the programme LIST indicate there is no station name assigned. BLUE Turn the programme edit. Watching TV / Programme control Pr.Edit 33 Watching TV / Programme control ■■Selecting a programme in the programme list 1 2 Watching TV / Programme control 34 The mode will be switched between TV, DTV, and Radio from the program you are currently watching. Select a programme. Switch to the chosen programme number. ■■Paging through a programme list 1 Turn the pages. 2 Return to normal TV viewing. Input List HDMI and AV(SCART) can be recognized by a detect pin and thus enabled only when an external device approves voltage. By using TV/RAD button, you can move from External Input to RF Input and to the last watched programme in DTV/RADIO/TV mode. ■■ Image shown may differ from your TV. Input List USB AV Component RGB OK HDMI1 HDMI2 Input Label 1 Select the input source. Exit •A ntenna or Cable : Select it when watching the DTV/RADIO/TV. • USB : Select it when using USB depends on connector. • AV : Select it when watching the VCR or external equipment. • Component : Select it when using the DVD or the Digital set-top box depends on connector. • RGB :Select it when using PC depends on connector. • HDMI : Select it when using DVD, PC or Digital set-top box depend on connector. Watching TV / Programme control Antenna Move 35 Watching TV / Programme control Input Label Selects a label for each input source. ■■ Image shown may differ from your TV. Input Label Input List Antenna Move USB AV Component RGB OK Watching TV / Programme control ◄ ► Component ◄ ► RGB ◄ ► HDMI1 ◄ ► HDMI2 ◄ ► HDMI1 HDMI2 Input Label AV Exit ▼ Close 1 2 3 BLUE Select Input Label. Select the source. Select the label. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 36 Data Service (This menu is enabled only in Ireland. ) This function allow users to choose between MHEG(Digital Teletext) and Teletext if both exist at the same time. If only one of them exists, either MHEG or Teletext is enabled regardless of which option you selected. ● Demo Mode Move OPTION OK : Off ● Demo ● Language(Language) ● Country ● Country : Ireland Indicator ● Factory ● Set 1 ID ● Power Reset ● Factory :1 ● Set ID MHEG MHEG Indicator ● Data Service ► : :MHEG MHEG ► ● Data Service : Ireland ● Disability Assistance ► ● Power OK : Off ● Language(Language) ● Disability Assistance Teletext MHEG : :MHEG Reset :1 Select OPTION. 2 Select Data Service. 3 4 Mode Move Watching TV / Programme control OPTION Select MHEG or Teletext. Save. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 37 Watching TV / Programme control SIMPLINK This function operates only with devices with the SIMPLINK logo. Please check the SIMPLINK logo. This TV might not function properly when using it with other products with HDMI-CEC function. This allows you to control and play other AV devices connected to the display through HDMI cable without additional cables and settings. If you do not want SIMPLINK menu,select “Off”. Watching TV / Programme control In wireless external output, SIMPLINK function is not supported. OK ◄ On Exit ► Watch TV DISC VCR VCR Recorder HDD ◄ Speaker TV Speaker 1 2 3 ► Display the SIMPLINK. Select On or Off. Save. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 38 Connecting to Home Theater with the SIMPLINK logo. 1 Connect the HDMI/DVI IN 1, HDMI 2 (Except for 22LD3***) terminal on the back of the TV and the HDMI output terminal of the Home Theater using HDMI cables. Connect the Digital Audio output terminal on the back of the TV and the Digital Audio input terminal of the Home Theater using optical cables. 3 Select Home Theater in the Speaker menu by pushing the SIMPLINK button. ►► When you select or operate a media device with home theater function, the speaker automatically switches to home theater speaker (HT speaker). VOLUME CONTROL 2 /DVI IN 1 (8 ) SPEAKER OUT 1 2 Home Theater ANTENNA IN Watching TV / Programme control 2 (RGB) NOTE ►►Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the terminal (HDMI terminal) of the SIMPLINK device with the HDMI cable. ►►When you switch the Input source using the INPUT button on the remote control, you can stop the operation of a device controlled by SIMPLINK. 39 Watching TV / Programme control Simplink Functions Watching TV / Programme control 40 Disc playback Control connected AV devices by pressing the , OK, ►, ▀, l l, ◄◄ and ►► buttons. Direct Play After connecting AV devices to the TV, you can directly control the devices and play media without additional settings. Select AV device Enables you to select one of the AV devices connected to the TV and operate it. Power off all devices When you switch off the TV, all connected devices are turned off. Switch audio-out Offers an easy way to switch audio-out. Sync Power on When the equipment with Simplink function connected HDMI terminal starts to play, The TV will change automatically to turn on mode. * A device, which is connected to the TV through an HDMI cable but does not support SIMPLINK, does not provide this function. Note: To operate SIMPLINK, an High Speed HDMI Cable with *CEC function should be used. (*CEC: Consumer Electronics Control). SimpLink Menu Press the 1 2 3 5 TV viewing : Switch to the previous TV programme regardless of the current mode. DISC playback : Select and play connected discs. When multiple discs are available, the device type of discs are conveniently displayed at the bottom of the screen. VCR playback : Play and control the connected VCR. HDD Recordings playback : Play and control recordings stored in HDD. OK ◄ On Exit ► 1 Watch TV Selected Device 2 DISC 3 VCR When a device is connected (displayed in bright colour) 4 VCR Recorder HDD 5 ◄ Speaker TV Speaker ► When device is not connected (displayed in gray) udio Out to Home theater/Audio Out to A TV: Select Home theater or TV speaker for Audio Out. • Home theater: Only one supported at a time • DVD, Recorder: Up to one(Only 22LD3***), two(Only 26/32/37LD3***) supported at a time. • VCR: Only one supported at a time Watching TV / Programme control 4 button and then OK button to select the desired SIMPLINK source. 41 Watching TV / Programme control AV Mode You can select the optimal images and sounds when connecting AV devices to external input. Off Cinema Sport Game Watching TV / Programme control 1 AV MODE Disables the AV MODE. Optimizes video and audio for watching movies. Optimizes video and audio for watching sports events. Optimizes video and audio for playing games. Off Cinema Game Sport Press the AV MODE button repeatedly to select the desired source. 2 • If you select Cinema in AV mode, Cinema will be selected both for Picture Mode and Sound Mode in PICTURE menu and AUDIO menu respectively. • If you select “Off” in AV mode, the picture and image which you initially set will be selected. 42 Initializing(Reset to original factory settings) This function initializes all settings. It is useful to initialize the product or when you move to other city or country. When the Factory Reset is completed, you must restart the Initializing setup. When the Lock System menu is "On", the message to enter the password appears. ● Demo Mode Move 4 Move ● Country ● Disability Assistance ● Disability Assistance ● Power ● Power Indicator ID ► :1 Select OPTION. OK : Off ● Language(Language) : UK ► 3 Mode ● Country ● Set 2 ● Demo ● Language(Language) ● ● Factory Factory Reset Reset 1 OPTION OK : Off : UK All user settings and channel settings will Indicator be reset. Still Continue? ● Factory Reset ● Set ID :1 Yes No • In Lock System "On", if you forget your password, press '0', '3', '2', '5' on the remote control hands et. Watching TV / Programme control OPTION Select Factory Reset. Select Yes. Start Factory Reset. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 43 To use a USB device When connecting a USB device When you connect a USB device, this pop up menu is displayed, automatically. “POP UP MENU” will not be displayed while the OSD including Menu or EPG is activated. When the Pop Up menu appears, you can select Music List, Photo List, Movie List or Extra Contents in the MY MEDIA menu. In USB device, you can not add a new folder or delete the existing folder. 1 Connect the USB device to the USB IN jack on the TV. To use a USB device or When removing the USB device Select the USB Device menu before removing the USB device. 2 Select Movie List, Photo List, Music List or Extra Contents. 1 2 MY MEDIA Movie List Photo List Press OK( Music List Extra Contents ) to see photos from the USB. Option 3 44 •O nly photo(JPEG), music (MP3) and movie (DAT,MPG,MPEG,VOB,AVI,DIVX,MP4,MKV,T S,TRP,TP,ASF,WMV,FLV) are supported. Exit Select USB Device. Select Eject. Precautions when using the USB device To use a USB device ►►Only a USB storage device is recognizable. ►►If the USB storage device is connected through a USB hub, the device is not recognizable. ►►A USB storage device using an automatic recognition programme may not be recognized. ►►A USB storage device which uses its own driver may not be recognized. ►►The recognition speed of a USB storage device may depend on each device. ►►Please do not turn off the TV or unplug the USB device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged. ►►Please do not connect the USB storage device which was artificially maneuvered on the PC. The device may cause the product to malfunction or fail to be played. Never forget to use only a USB storage device which has normal music files, image files or movie files. ►►Please use only a USB storage device which was formatted as a FAT32 file system, NTFS file system provided with the Windows operating system. In case of a storage device formatted as a different utility programme which is not supported by Windows, it may not be recognized. ►►Please connect power to a USB storage device(over 0.5 A) which requires an external power supply. If not, the device may not be recognized. ►►Please connect a USB storage device with the cable offered by the device maker. ►►Some USB storage devices may not be supported or operated smoothly. ►►File alignment method of USB storage device is similar to Window XP and filename can recognize up to 100 English characters. ►►Be sure to back up important files since data stored in a USB memory device may be damaged. We will not be responsible for any data loss. ►►If the USB HDD does not have an external power source, the USB device may not be detected. So be sure to connect the external power source. - Please use a power adaptor for an external power source. We do not guarantee an USB cable for an external power source. ►►If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use up to 4 partitions or USB memory devices. ►►If a USB memory device is connected to a USB multi-card reader, its volume data may not be detected. ►►If the USB memory device does not work properly, disconnect and reconnect it. ►►How fast a USB memory device is detected differs from device to device. ►►If the USB is connected in Standby Mode, specific hard disk will automatically be loaded when the TV is turned on. ►►The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USB memory. ►►Any device with more than the recommended capacity may not work properly. ►►If a USB external hard disk with a "Energy Saving" function does not work, turn the hard disk off and on again to make it work properly. ►►USB storage devices below USB 2.0 are supported as well. But they may not work properly in the movie list. ►►Maximum of 999 folders or files can be recognized under one folder. 45 To use a USB device Movie list You can play movie files on a USB storage device. The movie list is activated once USB is detected. It is used when playing movie files on TV. Displays the movies in the USB folder and supports Play. Allows playback of all movies in the folder and user desired files. It is a movie list that displays folder information and movie file. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. Movie(*.mpg/*.mpeg/*dat/*.ts/*.trp/*.tp/*.vob/*.mp4/*.mov/*.mkv/*.dvix/*.avi/*.asf/*.wmv/*.flv/*.avi(motion-jpeg)/*. mp4(motion-jpeg)/*.mkv(motion-jpeg))supporting file Video format : DivX3.11, DivX4.12, DivX5.x, DivX6, Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03, Xvid1.10 beta-1/beta-2, Mpeg-1, Mpeg-2, Mpeg-4, H.264/AVC, VC1, JPEG, Sorenson H.263 Audio format : Dolby Digital, AAC, Mpeg, MP3, LPCM, HE-AAC, ADPCM, WMA Bit rate : within 32 kbps to 320 kbps(MP3) To use a USB device External Subtitle format : *.smi/*.srt/*.sub(MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.psb(PowerDivX) Internal Subtitle format : only, XSUB (It is the subtitle format used in DivX6 files) • Some user-created subtitles may not work properly. • Some special characters are not supported in subtitles. • HTML tags are not supported in subtitles. • Subtitles in languages other than the supported languages are not available. • The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audio language is changed. • A damaged movie file may not be played correctly, or some player functions may not be usable. • Movie files produced with some encoders may not be played correctly. • If the video and audio structure of recorded file is not interleaved, either video or audio is outputted. • HD videos with a maximum of 1920x1080@25/30P or 1280x720@50/60P are supported, depending on the frame. • Videos with resolutions higher than 1920X1080@25/30P or 1280x720@50/60P may not work properly depending on the frame. • Movie files other than the specified types and formats may not work properly. • Max bitrate of playable movie file is 20 Mbps. (only, Motion JPEG : 10 Mbps) • We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC. • DTS Audio codec is not supported. • A movie file more than 30 GB in file size is not supported for playback. • A DivX movie file and its subtitle file must be located in the same folder. • A video file name and its subtitle file name must be identical for it to be displayed. • Playing a video via a USB connection that doesn’t support high speed may not work properly. • Files encoded with GMC(Global Motion Compensation) may not be played. • When you are watching the movie by Movie List function, you can adjust an image by Energy Saving and AV Mode key on the remote control. User setup for each image mode does not operate. 46 File Video Decoder Audio Codec mpg, mpeg MPEG1, MPEG2 MP2,MP3,Dolby Digital,LPCM dat MPEG1 Extension name ts,trp,tp MPEG2, H.264, AVS, VC1 Max Resolution MP2 MP2,MP3,Dolby Digital, AAC,HE-AAC vob MPEG1, 2 MP2,MP3,Dolby Digital,LPCM mp4, mov MPEG4,DivX 3.11, DivX 4.12, DivX 5.x, DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1/2H.264 AAC,HE-AAC,MP3 mkv H.264, MPEG-1,2,4 divx, avi MPEG2, MPEG4,DivX 3.11, DivX 4. DivX 5, DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1/2H.264 Motion JPEG (avi, mp4, mkv) JPEG LPCM, ADPCM asf, wmv VC1 WMA flv Sorenson H.263, H264 MP3, AAC MP2,MP3,Dolby Digital,AAC 1920x1080@30p HE-AAC,LPCM (only , Motion JPEG 640x480@30p) MP2,MP3,Dolby Digital,LPCM, ADPCM,AAC,HE-AAC To use a USB device 47 To use a USB device Screen Components You can also adjust USB in the INPUT menu. 1 Select MY MEDIA. 2 Select Movie List. 2 1 1 2 3 4 5 To use a USB device Moves to upper level folder Current page/Total pages Corresponding buttons on the remote control Contents under the folder focused on 1 Current page/ total pages of contents under the folder focused on 1 Drive1 001 002 005 006 Page 1/1 003 5 004 4 Move To Photo List Play Mark Mode Change Numbers P Page Change MARK Mark Exit 3 • Some files may be displayed the preview image by icon only. 48 Page 1/1 Movie List • Non-supported files are displayed the preview image by icon only. • Abnormal files are displayed in the form of bitmap. Movie Selection ■■When playing movie files Page 1/1 Movie List Drive1 Page 1/1 001 002 003 005 006 051. Apple_ ...... 02:30:25 Move To Photo List Select the target folder or drive. 2 Play P Page Change movie page. Mark Exit Mark Mode • Use the P MARK button to navigation in the Select the desired movie title. 3 Movie files are played. To use a USB device 1 Change Numbers 004 Using the remote control GREEN Repeatedly, press the GREEN button to converted to Photo List->Music List. YELLOW A method to view in 5 large thumbnail or simple list. BLUE Convert to Mark Mode. Return to normal TV viewing. EXIT ► Press the PLAY(►) button to return to normal playback. 49 To use a USB device ■■When selected movie files are played Page 1/1 Movie List Mark Mode Drive1 Page 1/1 001 002 003 005 006 051. Apple_ ...... 02:30:25 Move Play Marked 1 Mark All P Page Change Exit Mark Mode To use a USB device Select the desired movie title. BLUE or 4 5 Mark Select the target folder or drive. 2 3 Unmark All 004 MARK MARK Mark Exit • When one or more movie files are marked, the marked movies will be played in sequence. Convert to Mark Mode. Mark desired Movie file. RED Marked movie file is played. NOTE ►►In the case of files not supported, a message regarding non-supported file is displayed. 50 Using the remote control RED Play the selected movie file. Once a movie file finishes playing, the next selected one will be played automatically. GREEN Mark all movie files on the screen. YELLOW Deselect all marked movie files. BLUE Exit the Mark Mode. EXIT Return to normal TV viewing. ►►If you select “Yes” from OSD when playing the same file after the movie file has been stopped, it will restart where it stopped previously. ►►If continuous series files exist within the folder, the next file will automatically be played. But, this excludes cases when the Repeat function of Movie List Option is turned “On” (Refer to p. 54) or when set as Marked Play. To use a USB device NOTE 51 To use a USB device Using the Movie List function, play Choose options. Set Video Play. Set Video. Set Audio. ■ To use a USB device 1 2 Close ◄► ► ► II or 01:02:30 / 02:30:25 ◄◄ ►► Q.MENU Option Hide Exit Show the Option menu. Select Set Video Play., Set Video. or Set Audio.. NOTE ►►Option values changed in Movie List does not affect Photo List and Music List. ►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List excluding Movie List. ►►When replaying the video file after stopping, you can play from where it stopped previously. 52 Using the remote control ■ ► II ◄◄ / ►► Stop the playing movie file. Press the PLAY(►) button to return to normal playback. During playback, press the Pause(II) button. ■■ Still screen is displayed. ■■ If no buttons are pressed on the remote control for 10 minutes after pausing, the TV returns to the playback state. ■■ Press the Pause(II) button and then use the FF(►►) button for slow motion. When playing, repeatedly, press the REW(◄◄) button to speed up ◄◄(x2) -> ◄◄◄(x4) -> ◄◄◄◄(x8) ->◄◄◄◄◄(x16) ->◄◄◄◄◄◄(x32) . repeatedly, press the FF(►►) button to speed up ►►(x2)-> ►►►(x4) -> ►►►►(x8) ->►►►►►(x16) -> ►►►►►►(x32). ■■ Pressing these buttons repeatedly increases the fast forward/reverse speed. or Show the Option menu. Hide the menu on the full-sized screen. ■■ To see the menu again on the full-sized screen, press OK button to display. Return to normal TV viewing. <> ENERGY SAVING AV MODE ■■ When using the < or > button during playback a cursor indicating the position can be viewed on the screen. To use a USB device MENU Press the ENERGY SAVING button repeatedly to change the brightness of your screen.(Refer to p. 86) Press the AV MODE button repeatedly to select the desired source.(Refer to p. 42) 53 To use a USB device ■■When you select the Set Video Play, Set Video Play. Picture Size ◄ Full ► Audio Language ◄ 1 ► Subtitle Language ◄ On ► ● Language ◄ English ► ● Code page ◄ Default ► ● Sync ◄ 0 ► ● Position ◄ 0 ► ● Size ◄ Normal ► Repeat ◄ On ► Previous 1 To use a USB device 2 Select Picture Size, Audio Language, Subtitle Langugae or Repeat. Make appropriate adjustments. Subtitle Language Support Language Latin1 English, Spanish, French, German, Italian, Swedish, Finnish, Dutch, Portuguese, Danish, Romanian, Norwegian, Albanian, Gaelic, Welsh, Irish, Catalan,Valencian Latin2 Bosnian, Polish, Croatian, Czech, Slovak, Slovenian, Serbian, Hungarian Latin4 Estonian, Latvian, Lithuanian Cyrillic Bulgarian, Macedonian, Russian, Ukrainian, Kazakh Greek Greek Turkish Turkish ►Picture ► Size : Selects your desired picture format during movie play. ►Audio ► Language : Changes the Language Group of the audio during movie play. Files with a single audio track cannot be selected. ►►Subtitle Langugae : Turn on/off the subtitle. ►Subtitle ► : Turn on/off the external subtitle. : Activated for SMI subtitle and ►Language ► can select the language within the subtitle. page : Can select the font for subti►Code ► tle. When set to default, same font as general menu will be used. : Adjusts the time synchronisation of ►Sync ► the subtitle from -10 secs to +10 secs by steps of 0.5 secs during movie play. ►Position ► : Changes the position of the subtitle either up or down during movie play. : Selects your desired Subtitle size ►Size ► during movie play. : Turn on/off repeat function of ►Repeat ► movie playback. When turned on, the file within the folder will be played back repeatedly. Even when the repeated playback is turned off, it can run the playback if the file name is similar to the previous file. NOTE ►►Only 10,000 of sync blocks can be supported within the subtitle file. ►►When playing a video, you can adjust the Picture Size by pressing the RATIO button. 54 ■■When you select the Set Video, Set Video. Picture Mode ◄ ◄ ● Contrast 100 ◄ ● Brightness 50 ◄ ► ● Colour 60 ◄ ► ► ● Dynamic Contrast ◄ Medium ► ● Edge Enhancer ◄ Low ► ● Noise Reduction ◄ Off ► Previous Select Picture Mode. Make appropriate adjustments. (Refer to p. 88 to 93) To use a USB device 2 ► 70 Picture Reset 1 Standard ● Backlight 55 To use a USB device ■■When you select the Set Audio, Set Audio. Sound Mode ◄ Standard ► Auto Volume ◄ Off ► Clear Voice II ◄ Off ► Balance 0 ◄ L R ► Previous To use a USB device 56 1 2 Select Sound Mode, Auto Volume, Clear Voice II or Balance. Make appropriate adjustments. (Refer to p. 96 to 101) Photo list You can view photo files on USB storage device. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. When you are watching the photo by the Photo List function, you can not change the picture mode. PHOTO(*.JPEG) supporting file Baseline : 64 x 64 to 15360 x 8640 Progressive : 64 x 64 to 1920 x 1440 • You can play JPEG files only. • Non-supported files are displayed in the form of predefined icon. Screen Components You can also adjust USB in the INPUT menu. Select MY MEDIA. 2 Select Photo List. 2 1 1 2 3 4 5 Moves to upper level folder Current page/Total pages Corresponding buttons on the remote control Contents under the folder focused on 1 Current page/ total pages of contents under the folder focused on 1 Page 1/1 Photo List Drive1 001 010 002 011 Page 1/1 003 004 005 006 012 013 014 015 Move To Music List 007 009 4 View Mark Mode Change Numbers 008 5 To use a USB device 1 P Page Change MARK Mark Exit 3 57 To use a USB device Photo Selection ■■When playing photo files Page 1/1 Photo List Drive1 001 010 002 011 Page 1/1 003 004 005 006 012 013 014 015 Move To Music List To use a USB device 1 Select the target folder or drive. 2 3 Change Numbers 008 007 View P Page Change Mark Mode • Use the P photo page. 009 MARK Mark Exit button to navigation in the Select the desired photos. Photo files are displayed. Using the remote control GREEN Repeatedly, press the GREEN button to converted to Music List->Movie List. YELLOW A method to view in 5 large thumbnail or simple list. BLUE Convert to Mark Mode. Return to normal TV viewing. 58 ■■When selected photo files are displayed Page 1/1 Photo List Mark Mode 001 002 010 011 Drive1 Page 1/1 003 004 005 006 012 013 014 015 Move View Marked Select the target folder or drive. 2 3 Select the desired photos. BLUE or 4 5 Unmark All MARK Convert to Mark Mode. Mark P Page Change Exit Mark Mode 009 MARK Mark Exit • When one or more photos are marked, you can view each marked photo or a slide show of the marked photos. If no photos are marked, you can view every individual photo in the folder or a slide show of all photos in the folder. To use a USB device 1 Mark All 008 007 Mark desired photo file. RED Marked photo file is displayed. 59 To use a USB device Using the remote control RED Display the selected photo file. GREEN Mark all photo files on the screen. YELLOW Deselect all marked photo files. BLUE Exit the Mark Mode. Return to normal TV viewing. To use a USB device 60 How to view photo Detailed operations are available on full-sized photo view screen. Page 1/1 Photo List Drive1 001 002 010 011 Page 1/1 003 004 005 006 012 013 014 015 Move To Music List 008 007 View P Page Change MARK Mark Exit Mark Mode Change Numbers 009 ◄ ► The aspect ratio of a photo may change the size of the photo displayed on the screen in full size. Press the EXIT button to move to the previous menu screen. ◄ Slideshow 1 2 3 ► BGM ■ 2/13 ► Q.MENU Option Select the target folder or drive. Hide To use a USB device 01_a.jpg 2008/12/10 1920 x 1080 479 KB Exit • Use the P photo page. button to navigation in the Select the desired photos. The selected photo is displayed in full size. • Press the EXIT button to go back to Photo List. • Press the BACK button to make Help OSD disappear. 61 To use a USB device 01_a.jpg 2008/12/10 1920 x 1080 479 KB 4 ◄ • Use Slideshow ► BGM ■ 2/13 ► Q.MENU Option Hide Exit ►►Slideshow : When no picture is selected, all photos in the current folder are displayed during slide show. If some photos are selected, those photos are displayed in a slide show. ■ Set the time interval of the slide show in Option. To use a USB device ►►BGM (Background Music) : Listen to music while viewing photos in full size. ■ Set the BGM device and album in Options before using this function. ■ You can adjust Option by Q.MENU or MENU button on the remote control. ►► � (Rotate) : Rotate photos. ■ Rotates the photo 90°, 180°, 270°, 360° clockwise. ■ It can not be rotate when the width of a picture is bigger than supported height. ►► (ZOOM IN): View the photo by zoom in 2, 4 times. ►► : Press the ENERGY SAVING button repeatedly to change the brightness of your screen.(Refer to p. 86) ►►Option : Set values for Slide Speed and BGM. ■ Use button and OK button to set values. Press OK to save the settings. ■ You cannot change BGM while BGM is playing. ►►Hide : Hide the menu on the full-sized screen. ■ To see the menu again on the full-sized screen, press OK button to display. Press the EXIT button to go back to Photo List. 62 BGM, � (Rotate), (ZOOM IN), , Option, Hide or Exit. ► ◄ Select the Slideshow, button to select the previous or next photo. • Use button to select and control the menu on the full-sized screen. Using the Photo List function 01_a.jpg 2008/12/10 1920 x 1080 479 KB Choose options. ◄ ► Set Photo View. Set Video. Set Audio. Close ◄ Slideshow 1 or BGM ■ 2/13 ► Q.MENU Option Hide Exit Show the Option menu. Select Set Photo View., Set Video. or Set Audio.. NOTE ►►Option values changed in Movie List does not affect Photo List and Music List. ►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List excluding Movie List. To use a USB device 2 ► 63 To use a USB device ■■When you select the Set Photo View, Set Photo View. Slide Speed ◄ Fast ● Repeat ◄ On ► ● Random ◄ Off ► BGM ► ... Previous 1 2 To use a USB device 64 Select Slide Speed or BGM. Make appropriate adjustments. ■■When you select the Set Video, Set Video. Picture Mode ◄ ◄ ● Contrast 100 ◄ ● Brightness 50 ◄ ► ● Colour 60 ◄ ► ► ● Dynamic Contrast ◄ Medium ► ● Edge Enhancer ◄ Low ► ● Noise Reduction ◄ Off ► Previous Select Picture Mode. Make appropriate adjustments. (Refer to p. 88 to 93) To use a USB device 2 ► 70 Picture Reset 1 Standard ● Backlight 65 To use a USB device ■■When you select the Set Audio, Set Audio. Sound Mode ◄ Standard ► Auto Volume ◄ Off ► Clear Voice II ◄ Off ► Balance 0 ◄ L R ► Previous To use a USB device 66 1 2 Select Sound Mode, Auto Volume, Clear Voice II or Balance. Make appropriate adjustments. (Refer to p. 96 to 101) Music list You can play music files on USB storage device. Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be supported by this model. Music file on your USB device can be played by this unit. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. MUSIC (*.MP3) supporting file Bit rate 32 to 320 • Sampling rate MPEG1 Layer3 : 32 kHz, 44.1 kHz, 48 kHz • Sampling rate MPEG2 Layer3 : 16 kHz, 22.05 kHz, 24 kHz • Sampling rate MPEG2.5 Layer3 : 8 kHz, 11.025 kHz, 12 kHz To use a USB device Screen Components You can also adjust USB in the INPUT menu. 1 1 2 3 4 5 6 Select MY MEDIA. Preview: If any album jacket for the file(Album Art Image) exists, this jacket is displayed. Moves to upper level folder Current page/Total pages Corresponding buttons on the remote control Contents under the folder focused on 2 Current page/ total pages of contents under the folder focused on 2 2 Select Music List. 3 2 Page 1/1 Music List Drive1 1 001. - B01.mp3 00:00 002. - B02.mp3 00:00 Page 1/1 003. - B03.mp3 00:00 005. - B05.mp3 00:00 5 Move To Movie List 6 004. - B04.mp3 00:00 Change Numbers Play Mark Mode P Page Change MARK Mark Exit 4 67 To use a USB device Music Selection Page 1/1 Music List Drive1 001. - B01.mp3 00:00 Page 1/1 002. - B02.mp3 00:00 003. - B03.mp3 00:00 004. - B04.mp3 00:00 005. - B05.mp3 00:00 Move To Movie List Change Numbers ■■When playing music files 1 Page Change Mark Mode MARK Mark Exit • Use the P button to navigate up/down in the music page. To use a USB device Select the desired music title. Music files are played. Using the remote control GREEN Repeatedly, press the GREEN button to converted to Movie List->Photo List. YELLOW A method to view in 5 large thumbnail or simple list. BLUE Convert to Mark Mode. Return to normal TV viewing. 68 P Select the target folder or drive. 2 3 Play ■■When selected music files are played Page 1/1 Music List Mark Mode Drive1 001. - B01.mp3 00:00 Page 1/1 002. - B02.mp3 00:00 003. - B03.mp3 00:00 004. - B04.mp3 00:00 005. - B05.mp3 00:00 Move Play Marked Select the target folder or drive. 2 3 Select the desired music title. BLUE or 4 5 MARK Convert to Mark Mode. Mark desired music file. RED Unmark All P Page Change Exit Mark Mode MARK Mark Exit • When one or more music files are marked, the marked music title will be played in sequence. For example, if you want to listen to only one music repeatedly, just mark the music only and play it. If no music is marked, all the music in the folder will be played in sequence. • If you want to activate Random playback, you must set Option->Set audio play.->Random to On. To use a USB device 1 Mark All Mark Marked music file is played. 69 To use a USB device Using the remote control RED Display the selected music file. GREEN Mark all music files on the screen. YELLOW Deselect all marked music files. BLUE Exit the Mark Mode. Return to normal TV viewing. To use a USB device 70 Using the Music List function, play Page 1/1 Music List 3 file(s) Marked Drive1 Page 1/1 Set Audio Play. ► 004. - B04.mp3 00:00 005. - B05.mp3 00:00 ► 005. - B05.mp3 ■ 1 II ◄◄ ►► or Set Audio. 006. - B06.mp3 00:00 ◄► Play with Photo 007. - B07.mp3 00:00 008. - B08.mp3 00:00 Close 02:30 / 03:25 Q.MENU Option Hide Exit Show the Option menu. Select Set Audio Play. or Set Audio. NOTE ►►Option values changed in Movie List does not affect Photo List and Music List. ►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List excluding Movie List. To use a USB device 2 ► Choose options. 71 To use a USB device Using the remote control ■ ► II ◄◄ / ►► GREEN ENERGY SAVING To use a USB device 72 MENU or Stop the playing music file. Press the PLAY(►) button to return to normal playback. When you press the Pause(II) button while playing the file, the playback will be paused. When you press the Pause(II) button again while the playback is paused, it will resume the playback. When playing, When you press the REW(◄◄) button, the previous music file will be played. When you press the FF(►►) button, the next music file will be played. Start playing the selected music files and then move to the Photo List. Press the ENERGY SAVING button repeatedly to change the brightness of your screen.(Refer to p. 86) Only Off/Screen Off operates from the Movie List, Photo List, Music List. Show the Option menu. ■■ When you press the Back button while the music is playing, the music player currently playing will be hidden and only the music list will be displayed. ■■ When you press the Exit button while the Music player is displayed, only the music will be stopped and the player will not return to normal TV viewing. ■■ When you press the Exit button while the music is stopped or while the music player is hidden, the player will return to normal TV viewing. <> ■■ When using the < or > button during playback a cursor indicating the position can be played. ■■When you select the Set Audio Play, Set Audio Play. Repeat ◄ On ► Random ◄ Off ► Previous 1 2 Select Repeat or Random. Make appropriate adjustments. To use a USB device 73 To use a USB device ■■When you select the Set Audio, Set Audio. Sound Mode ◄ Standard ► Auto Volume ◄ Off ► Clear Voice II ◄ Off ► Balance 0 ◄ L R ► Previous 1 To use a USB device 2 Select Sound Mode, Auto Volume, Clear Voice II or Balance. Make appropriate adjustments. (Refer to p. 96 to 101) ■■ If you don't press any button for a while during the playing, the play information box (as shown in the below) will float as a screen saver. ■■ The ‘Screen Saver’? Screen saver is to prevent screen pixel damage due to an fixed image remaining on the screen for a extended period of time. 002. B02.mp3 ► 00:31 / 04:04 NOTE ►►A damaged or corrupted music does not play but displays 00:00 in playtime. ►►A music downloaded from a paid service with copyright protection does not start but displays inappropriate information in playtime. ►►If you press OK, ■ buttons, screen saver is stopped. ►►The PLAY(►), Pause(II), ■ , ►►, ◄◄ buttons on the remote control are also available in this mode. ►►You can use the ►► button to select the next music and the ◄◄ button to select the previous music. 74 Extra contents You can play application files on USB device. Application files your device can be played by this unit. The On Screen Display may be different from your TV. Images are an example to assist with the TV operation. FLASH (*.SWF) / GEM supporting file An SWF file complied with Flash Lite 3.0 or earlier (the 3.0 version is recommended) ■■When playing Application files 1 Select MY MEDIA. 2 3 To use a USB device •T he Pro:Centric application is required, which starts automatically in the flash memory when the TV is turned on. •T he folder called /hcapfs/as/abs_service/ must exist in USB drive root directory. •T he file called xait.xml must exist in the /hcapfs/as/abs_service/ folder. • If the above conditions are not met, the following error message is displayed when selecting the Extra Contents option: Failed to execute file in the USB. Please check the files in the USB. • When the flash file does not run even if the above all conditions are met, refer to the Download Extra Contents of Installation Guide. • GEM is composed of JAVA application. Select Extra Contents. Application files are played. ■■To stop playing the Application file Remove the USB from the USB IN jack of the TV set. NOTE ►When ► playing the Application files(FLASH or GEM files), the buttons are controlled according to the settings of the Extra Contents option. 75 To use a USB device DivX Registration Code Confirm the DivX registration code number of the TV. Using the registration number, movies can be rented or purchased at www.divx.com/vod. With a DivX registration code from other TV, playback of rented or purchased DivX file is not allowed. (Only DivX files matched with the registration code of the purchased TV are playable.) MY MEDIA DivX Reg.Code Deactivation Movie List Photo List Press OK( Music List Extra Contents To use a USB device 2 3 Close ) to see photos from the USB. Option 1 Previous You must register your device to play DivX protected videos. Registration code : ********** Register at http://vod.divx.com Exit Select MY MEDIA. BLUE Select DivX Reg. Code. Display DivX Reg. Code. • Press the MENU/EXIT button to return to normal TV viewing. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX,Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD. “DivX Certified to play DivX video up to HD 1080p, including premium content” “Pat. 7,295,673; 7,460,688; 7,519,274” NOTE ►►Movie files are supported as follows Resolution : under 1920x1080 WxH pixels Frame rate : under 30 frames/sec(1920x1080), under 60 frames/sec(under 1280x720) ►►Video Codec : MPEG 1, MPEG 2, MPEG 4, H.264/AVC, DivX 3.11, DivX 4.12, DivX 5.x, DivX 6, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1, Xvid 1.10-beta2, JPEG, VC1, Sorenson H.263/H.264. 76 Deactivation The purpose of deactivation is to allow deactivation of devices for users who have activated all the available devices through the web_server and are blocked from activating more devices. DivX VOD allowed the consumer to activate up to 6 devices under one account, but to replace or deactivate any of those devices, the consumer had to contact DivX Support and request deletion. Now with this added feature, consumers will be able to deactivate the device themselves and hence better manage their DivX VOD devices. MY MEDIA DivX Reg.Code Deactivation Movie List Photo List Press OK( Music List 3 4 No Exit Select MY MEDIA. BLUE Select Deactivation. Select Yes. To use a USB device 2 Yes ) to see photos from the USB. Option 1 Previous Extra Contents Deregistration code : ******** Deregister at http://vod.divx.com Continue with registration? Display Deactivation. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 77 EPG(Electronic programme guide) (in digital mode) This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options. The EPG supplies information such as programme listings, start and end times for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of these programme details will vary, depending on the particular broadcaster). This function can be used only when the EPG information is broadcast by broadcasting companies. You must set the Clock in the Time menu, before using EPG function. The EPG displays the programme details for 8 days. ► DTV 1 TV ONE ► Pr. Change ► Next Watch Good Morning 21:00 00:00 Show/Game Show 16:9 720p ... HE-AAC Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking, with regular and special guests. Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking, with regular and special guests. ▼ Up Down Shows current programme information Displayed with a Teletext Programme. Displayed with a Radio Programme. Displayed with a Subtitle Programme. Displayed with a MHEG Programme. Displayed with a Scramble Programme. Displayed with a HE-AAC Programme. Displayed with a Dolby Digital Programme. Aspect ratio of broadcasting programme. Displayed with a Dolby Digital PLUS Programme. Aspect ratio of broadcasting programme. 576i/p, 720p, 1080i/p : Resolution of broadcasting programme Shows next programme information. Shows other programme information. ► DTV 2 TV2 ► EPG (Electronic programme guide)(in digital mode) 78 HE-AAC Displayed with a TV or DTV Programme. Tyra 21:00 00:00 Show/Game Show Talk show host Tyra Banks sits down with Keyshia Cole, the cast of Gossip Girl and Rihanna. Talk show host Tyra Banks sits down with Keyshia Cole, the cast of Gossip Girl and Rihanna. Pr. Change ◄ Now Switch on/off EPG 1 GUIDE Switch on or off EPG. Select a programme 1 or Select desired programme. EPG (Electronic programme guide)(in digital mode) 79 EPG (Electronic programme guide) Button Function in NOW/NEXT Guide Mode You can view a program being broadcasted and one scheduled to follow. RED Change EPG mode. Programme Guide ▲ That ’70s show 25 Nov. 2008 10:05 DTV 1 YLE TV1 25 Nov. 2008 09:45~10:15 When ‘Now’ is selected, it is moved to selected program and EPG disappears When ‘Next’ is selected, a reservation pop-up window appears. Select NOW or NEXT Programme. ALL NOW 1 YLE TV1 NEXT That ’70s show 2 YLE TV2 Your World Today 4 TV.. Legenen om Den.... 5 YLE FST Naturtimmen 6 CNN Lyssna 8 YLE24 Glamour INFO i Information ▼ Keno World Business Fantomen Kritiskt ABC Tänään otsikoissa Watch TV/RAD RADIO Mode Select the Broadcast Programme. or or Switch off EPG. Page Up/Down. Select DTV or RADIO Programme. EPG (Electronic programme guide)(in digital mode) 80 Detail information on or off Button Function in 8 Day Guide Mode Change EPG mode. Programme Guide ▲ That ’70s show 25 Nov. 2008 10:05 DTV 1 YLE TV1 25 Nov. 2008 09:45~10:15 ◄ GREEN Enter Date setting mode. ALL 14:00 Kungskonsumente Antigues Roadshow The Drum Mint Extra TV2: Farmen The Drum You Call The Hits Fashion Essentials ... ... ... Tänään otsikoissa 1 YLE TV1 4 TV.. 5 YLE FST 6 CNN 8 YLE24 ▼ Watch TV/RAD RADIO Date Page Up/Down. Select Programme. Select the Broadcast Programme. ... INFO i Information Mode Tue. 25 Nov. 15:00 ▼ 2 YLE TV2 When ‘Currently broadcasting programme is selected, it is moved to selected programme and EPG disappears When ‘Future broadcasting programme is selected, a reservation pop-up window appears. ◄ RED or or Switch off EPG. Detail information on or off EPG (Electronic programme guide)(in digital mode) Select DTV or RADIO Programme. 81 EPG (Electronic programme guide) Button Function in Date Change Mode or Programme Guide ▲ That ’70s show ALL Change to the selected date. 25 Nov. 2008 10:05 DTV 1 YLE TV1 25 Nov. 2008 09:45~10:15 ◄ 14:00 2 YLE TV2 4 TV.. Select a date. 5 YLE FST 6 CNN 8 YLE24 15:00 ▼ 1 YLE TV1 ... Kungskonsumente Antigues Roadshow The Drum Mint Extra TV2: Farmen The Drum You Call The Hits Fashion Essentials ... ... ... Tänään otsikoissa ▼ Date Change or EPG (Electronic programme guide)(in digital mode) 82 Switch off EPG. Tue. 25 Nov. ◄ GREEN or Switch off Date setting mode. Date Exit Button Function in Extended Description Box The detail information on or off. Text Up/Down. or Switch off EPG. DTV 1 YLE TV1 25 25 Nov. 2008 10:05 Fia World Touring Car Chanpionship Tue. 25 Nov. 2008 10:05 12:40 Fia Champion Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's Haunted house/Cry of The Swamp; Close EPG (Electronic programme guide)(in digital mode) 83 Picture Control Picture Size (Aspect Ratio) Control You can watch the screen in various picture formats; 16:9, Just Scan, Original, Full Wide, 4:3, 14:9, Zoom and Cinema Zoom. If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. You can adjust the enlarge proportion using button. This function works in the following signal. 1 2 Select Aspect Ratio. PICTURE menu. •F or Zoom Setting, select 14:9, Zoom and Select the desired picture format. picture control • 16:9 The following selection will allow you to adjust the picture horizontally, in linear proportion, to fill the entire screen(useful for viewing 4:3 formatted DVDs). Cinema Zoom in Ratio Menu. After completing Zoom Setting, the display goes back to Q.Menu. • Original When your TV receives a wide screen signal it will automatically change to the picture format broadcast. Original • Just Scan Following Selection will lead to you view the picture of best quality without loss of original picture in high resolution image. Note : If there is noise in original Picture, You can see the noise at the edge. Just Scan 84 •Y ou can also adjust Aspect Ratio in the • Full Wide When TV receives the wide screen signal,it will lead you to adjust the picture horizontally or vertically, in a linear proportion,to fill the entire screen fully. 4:3 and 14:9 video is supported in full screen without any video distortion through DTV input. Full Wide • 4:3 The following selection will allow you to view a picture with an original 4:3 aspect ratio. • 14:9 You can view a picture format of 14:9 or a general TV programme in the 14:9 mode. The 14:9 screen is viewed in the same way as in 4:3, but is moved to the up and down. • Zoom The following selection will allow you to view the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped. • Cinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note:When enlarging or reducing the picture, the image may become distorted. picture control ◄ or ► button: Adjust enlarge proportion of Cinema Zoom. The adjustment range is 1 to 16. ▼ or ▲ button: Move the screen. NOTE ►►You can only select 4:3, 16:9 (Wide), 14:9, Zoom/Cinema Zoom in Component mode. ►►You can only select 4:3, Original, 16:9 (Wide), 14:9, Zoom/Cinema Zoom in HDMI mode. ►►You can only select 4:3, 16:9 (Wide) in RGB-PC, HDMI-PC mode only. ►►In DTV/HDMI/Component (over 720p) mode, Just Scan is available. ►►In Analogue/DTV/AV/Scart mode, Full Wide is available. 85 picture control Energy Saving It reduces the TV’s power consumption. The default factory setting is adjusted to the comfortable level to be viewed at home. You can increase the brightness of your screen by adjusting the Energy Saving level or by setting the Picture Mode. When adjusting Energy Saving in MHEG mode, the Energy Saving setting is applied after MHEG is finished. Selecting ‘Screen Off’ while tuned to a radio station channel will reduce power consumption. ● Aspect 3 ● Aspect Mode ► : Standard ● Ratio Move : 16:9 Energy Saving :: Off Off ● Picture Mode OK Off Off : Standard • Backlight 70 • Backlight 70 • Contrast 100 • Contrast 100 • Brightness 50 • Brightness 50 • Sharpness 70 • Sharpness 70 • Colour 70 • Colour 70 ► picture control 2 : 16:9 Energy Saving :: Off Off ● Picture 1 Ratio PICTURE OK ► ● Move ► PICTURE Minimum Medium Maximum Screen Off Select PICTURE. Select Energy Saving. Select Off, Minimum , Medium, Maximum or Screen Off. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 86 • When you select Screen Off, the screen will be turned off in 3 seconds and Screen Off will start. • If you adjust “Energy Saving-Maximum”, Backlight feature will not work. • You can also adjust this feature by selecting Energy Saving button on the remote control. picture control 87 picture control Preset Picture Settings Picture Mode-Preset Strengthen the contrast, brightness, colour and sharpness for vivid picture. The most general screen display status. Optimizes video for watching movies. Optimizes video for watching sports events. Optimizes video for playing games. ● ● Ratio OK : 16:9 Energy Saving : Off Vivid ● Picture Mode : :Standard Standard ● Picture Mode : :Standard Standard • Backlight 70 • Backlight 70 • Contrast 100 • Contrast 100 • Brightness 50 • Brightness 50 • Sharpness 70 • Sharpness 70 • Colour 70 • Colour 70 Standard Standard Cinema Sport Game Expert1 Expert2 Select PICTURE. Select Picture Mode. Select Vivid, Standard, Cinema, Sport or Game. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. • Picture Mode adjusts the TV for the best picture appearance. Select the preset value in the Picture Mode menu based on the programme category. • You can also adjust Picture Mode in the Q. Menu. 88 ► 3 ● Aspect Move ► 2 : 16:9 Energy Saving : Off ► picture control 1 Ratio PICTURE OK ► ● Aspect Move ► PICTURE ► Vivid Standard Cinema Sport Game Manual Picture Adjustment Picture Mode-User option Backlight To control the brightness of the screen, adjust the brightness of LCD panel. Adjusting the backlight when setting the brightness of the set is recommended. Contrast Adjusts the signal level between black and white in the picture. You may use Contrast when the bright part of the picture is saturated. Brightness Adjusts the base level of the signal in the picture. Sharpness Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower the level, the softer the image. Colour Adjusts intensity of all colours. Tint Adjusts the balance between red and green levels. Colour Temp. Adjust to left direction to make a picture reddish or adjust to right direction to make a picture bluish. ● Ratio PICTURE OK : 16:9 ● Aspect Energy Saving : Off ● Ratio Move : 16:9 Energy Saving : Off Vivid • Backlight 70 • Contrast 100 • Contrast 100 • Brightness 50 • Brightness 50 • Sharpness 70 • Sharpness 70 • Colour 70 • Colour 70 ► : :Standard Standard 70 ► Select PICTURE. 2 Select Picture Mode. 3 Select Vivid, Standard, Cinema, Sport or Game. 4 Standard Standard Cinema Sport Game Expert1 Expert2 • Benefits of using Backlight - The electricity consumption is reduced by up to 60 %. - The black brightness is reduced. (As the black has greater depth, you can enjoy a better quality definition.) - You can adjust brightness with maintaining original signal resolution. picture control ● Picture Mode • Backlight ► : :Standard Standard ► ● Picture Mode 1 OK ► ● Aspect Move ► PICTURE Select Backlight, Contrast, Brightness, Sharpness, Colour, Tint or Colour Temp.. 5 Make appropriate adjustments. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. NOTE ►►You cannot adjust colour, sharpness and tint in the RGB-PC/HDMI-PC mode. ►►When the Expert 1/2 is selected, you can select Backlight, Contrast, Brightness, H Sharpness, V Sharpness, Colour or Tint. 89 picture control Picture Improvement Technology You can calibrate the screen for each Picture Mode or set the video value according to the special video screen. You can set the video value differently for each input. To reset to the factory default screen after making adjustments to each video mode, execute the “Picture Reset” function for each Picture Mode. Image shown may differ from your TV. PICTURE Move PICTURE OK • Sharpness 70 • Colour 60 • Tint 0 R G • Colour Temp. 0 W C • Advanced Advanced Control Control • Picture Reset ► OK • Sharpness 70 Dynamic Contrast • Colour • Tint • Colour Temp. 60 Dynamic Colour 0 R Clear White ► • Screen Move • Screen W ◄ Medium ► Medium G Off C Skin Colour • Advanced Advanced Control Control Noise Reduction • Picture Reset Digital Noise Reduction 0 Medium Medium Gamma Medium Black Level Auto ▼ Close picture control 1 2 3 4 Select PICTURE. Select Advanced Control. Select your desired Source.: Dynamic Contrast, Dynamic Colour, Clear White, Skin Colour, Noise Reduction, Digital Noise Reduction, Gamma, Black Level, Eye Care, Real Cinema, Colour Gamut or xvYCC. (Refer to p. 92 to 93) Make appropriate adjustments. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 90 Expert Picture Control By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. This may also be used to help a professional optimize the TV performance using specific videos. Image shown may differ from your TV. PICTURE ● Aspect ● Ratio Move PICTURE OK : 16:9 Energy Saving : Off Expert1 :: StandardVivid • Backlight Standard 70 • H Sharpness 70 Game • V Sharpness 70 Expert1 Expert1 • V Sharpness Digital60 Noise Reduction • Contrast • Screen ► 90 Cinema • Brightness Sport 50 ► • H Sharpness Noise 70 Reduction ● Picture Mode Expert2 MoveContrast OK Dynamic • Colour 60 R Black Level • Tint 0 Real Cinema Advanced Control •• Expert Control Colour Gamut • Picture Reset Edge Enhancer ◄ Medium ► Medium Medium G Auto On EBU High xvYCC Auto Expert Pattern Off ▼ Close 2 3 4 5 6 Select PICTURE. Select Picture Mode. Select Expert1 or Expert2. picture control 1 Select Expert Control. Select your desired Source. Make appropriate adjustments. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 91 picture control *This feature is not available for all models. Dynamic Contrast (Off/Low/Medium/High) Dynamic Colour (Off/Low/High ) ■■ Adjusts the contrast to keep it at the best level according to the brightness of the screen. The picture is improved by making bright parts brighter and dark parts darker. ■■ Adjusts screen colours so that they look livelier, richer and clearer. This feature enhances hue, saturation and luminance so that red, blue, green and white look more vivid. Skin Colour ■■ Adjusts skin colour of the picture so that user can set his favourite skin colour. (-5 to 5) Noise Reduction (Off/Low/Medium/High/ ■■ Reduces screen noise without compromising video quality. Auto(In Analogue Mode Only)) Digital Noise Reduction ■■ Reduces noise regarding MPEG compressed video. (Low/Medium/High/Off) picture control Gamma (Advanced Control: Low/Medium/High Expert Control: 1.9/2.2/2.4 ) Black Level (Low/High/Auto) • Low : The picture of the screen gets darker. • High : The picture of the screen gets brighter. • Auto : Sets black level of the screen to High or Low automatically according to the input signal level. ■■ Set black level of the screen to proper level. ■■ This function enables to select 'Low' or 'High' in the following mode: AV(NTSC-M), HDMI or Component. Otherwise, 'Black level' is set to 'Auto'. Clear White (Off/Low/High) ■■ Makes the white area of the screen brighter and clearer. Eye Care (Low/High/Off) *This feature is not available for all models. ■■ Adjusts the brightness of the screen automatically to the best level for eyes when the screen is too bright. ■■ This feature is disable in “Picture Mode-Vivid, Cinema, Expert1, Expert2”. Real Cinema (On/Off) 92 ■■ You can adjust brightness of dark area and middle gray level area of the picture. • Low/1.9 : Makes dark and middle gray level area of the picture brighter. • Medium/2.2 : Expresses original picture levels. • High/2.4: Make dark and middle gray level area of the picture darker. ■■ You can watch a cinema-like video by eliminating judder effect. ■■ Use this function when you watch film-originated movie contents. Colour Gamut (Advanced Control: Wide/Standard) • Standard : Mode to use original colour area regardless of the display char- Colour Temperature (Medium/Warm/Cool) Colour Management System This is the function to adjust the overall colour of the screen to the feeling you want. a. • Method : 2 Points • Pattern: Inner, Outer • Red/Green/Blue Contrast, Red/Green/Blue Brightness: The adjustment range is -50 to +50. b. • Method : 10 point IRE • Pattern: Inner / Outer • IRE (Institute of Radio Engineers) is the unit to display the size of the video signal and can be set among 10, 20, 30 to 100. You can adjust Red, Green or Blue according to each setting. • Luminance: This function displays calculated luminance value for 2.2 gamma. You can input luminance value you want at 100 IRE, than the target luminance value for 2.2 gamma is displayed at every 10 steps from 10 IRE to 90 IRE. • Red/Green/Blue: The adjustment range is -50 to +50. ■■ As the tool used by the experts to make adjustments by using the test patterns, this does not affect other colours but can be used to selectively adjust the 6 colour areas (Red/Green/Blue/Cyan/Magenta/Yellow). Colour difference may not be distinctive even when you make the adjustments for the general video. ■■ Adjusts Red/Green/Blue/Yellow/Cyan/Magenta. • Red/Green/Blue/Yellow/Cyan, Magenta Colour : The adjustment range is -30 to +30. • Red/Green/Blue/Yellow/Cyan/Magenta Tint : The adjustment range is -30 to +30. ■■ This feature is disable in RGB-PC and HDMI (PC) mode. picture control acteristics. • Wide: Mode to use maximum colour area of the TV display. ■■ Maximize the utilization for colour area that can be expressed. • Standard : Mode to use original colour area regardless of the display characteristics. Colour Gamut (Expert Control: EBU/ • Wide : Mode to use maximum colour area of the TV display. SMPTE/BT709/Wide/ • EBU : Mode to display EBU colour area. Standard) • SMPTE : Mode to display SMPTE colour area. • BT709 : Mode to display BT709 colour area. Edge Enhancer ■■ Makes the edge of the picture clearer and distinctive. (Off/Low/High) ■■ This function can use in “Picture Mode-Expert.” *This feature is not available for all models. xvYCC ■■ This is the function to express richer colour. (Auto/off/on) ■■ This function is enabled in "Picture mode - Cinema, Expert" when xvYCC signal is inputted through HDMI Expert Pattern ■■ This is the pattern necessary for checking the picture of Digital TV. (Off/Pattern1/Pattern2) ■■ This function is enabled in "Picture Mode - Expert" when you watch DTV. Colour Filter ■■ This is the function to filter the specific colours of the video. (Off/Red/Green/Blue) You can use the RGB filter to set colour saturation and hue accurately. 93 picture control Picture Reset Settings of the selected picture modes return to the default factory settings. PICTURE Move 70 • Colour 60 • Tint 0 R G • Colour Temp. 0 W C • Advanced Control •• Picture Picture Reset Reset 3 4 ► picture control 2 ► • Sharpness • Screen 1 PICTURE OK Move OK • Sharpness 70 • Colour 60 • Tint ? All picture 0 Rsetting willGbe reset. C • Colour Temp. Continue?W • Advanced Control •• Picture Picture Reset Reset Yes No • Screen Select PICTURE. Select Picture Reset. Select Yes. Initialize the adjusted value. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 94 Power Indicator Adjust the power/standby indicator light on the front of the TV. Standby Light Determines whether to set the indicator light on the front of the TV to On or Off in standby mode. Power Light Determines whether to set the indicator light on the front of the TV to On or Off when the power turns on. OPTION ● Demo Mode ● Demo Move Mode ● Language(Language) ● Country : UK : UK ● Disability Assistance ● Power Indicator ● Power Indicator ► ● Disability Assistance ► Reset ID ● Factory :1 ● Set 3 Select OPTION. Select Power Indicator. 4 OK : Off ● Country ● Set 2 OPTION OK ● Language(Language) ● Factory 1 Move : Off Standby Light ◄ Power Light On ► On Reset ID Close :1 Select Standby Light or Power Light. Select your desired Source. DEMO MODE Display the slide show to explain the various logo of this TV. The screen is reset automatically after 5 minutes in Demo Mode. ● Country ● Country : UK ● Disability Assistance ● Disability Assistance ● Power ● Power Indicator ID Reset Select OPTION. Select Demo Mode. ● Set 3 4 ID ► : Off ► On On OK : UK Indicator ● Factory :1 Off ► :: Off Off ● Language(Language) ● Set 2 ● Demo Demo Mode Mode ● Move ● Language(Language) ● Factory 1 :: Off Off OPTION OK ► ● Demo Mode Move ► OPTION picture control • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. Reset :1 Select On to show the various logo of TV. Return to TV viewing. If you want to stop the demo, press any button. (except for MUTE, +, - button) 95 Sound & Language control Auto Volume Leveler Auto Volume automatically remains on the same level of volume if you change programmes. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each programme. If sound quality or volume is not at the level you want, it is recommended to use a separate home theater system or amp to cope with different user environments. AUDIO Move ● Clear Voice II : Off 3 ● Balance ● Sound 1 2 sound & language control 3 Mode AUDIO OK : Off ● Auto ● Clear 0 L : Standard R Move Volume Voice II : Off ● Balance ● Sound Mode OK MHEG Off : Off 3 ► Volume ► ● Auto On 0 L R : Standard • Infinite Sound : Off • Infinite Sound : Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 • Reset • Reset Select AUDIO. Select Auto Volume. Select On or Off. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 96 Clear Voice II By differentiating the human sound range from others, it helps users listen to human voices better. AUDIO Volume : Off Off :: Off ● Balance ● Sound 1 3 33 0 L R : Standard • Infinite Sound : Off • Treble 50 • Bass 50 • Reset Select AUDIO. Move Volume Clear Voice Voice II II ●●Clear : Off Off :: Off ● Sound Mode ● Clear 33 ● Balance OK L 0 ● Level Voice II R ◄ 3 Off - 5 + : Standard • Infinite Sound : Off • Treble 50 • Bass 50 • Reset Close • If you select “On” for Clear Voice II, Infinite Sound feature will not work. • Select levels from ‘-6’ to ’+6’. Select Clear Voice II. Select On or Off. Adjustment for Clear Voice Level With selecting On 4 ► Select Level. Make desired adjustment. sound & language control 2 Mode ● Auto ► Clear Voice Voice II II ●●Clear AUDIO OK ► ● Auto Move • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 97 sound & language control Preset Sound Settings-Sound Mode You can select your preferred sound setting; Standard, Music, Cinema, Sport or Game and you can also adjust the Treble, Bass. Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content. Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory. Standard Music Cinema Sport Game Offers standard-quality sound. Optimizes sound for listening to music. Optimizes sound for watching movies. Optimizes sound for watching sports events. Optimizes sound for playing games. AUDIO Move Volume ● Clear Voice II : Off 3 Standard :: Standard 3 Volume ● Clear 0 L R Voice II Move OK : Off : Off ● Balance 3 L Standard 0 Standard Standard :: Standard • Infinite Sound : Off • Treble 50 • Infinite Sound : OffCinema • Treble 50 Sport • Bass 50 • Bass • Reset • Reset Select AUDIO. R Music Sound Mode Mode ●●Sound ► sound & language control 2 Sound Mode Mode ●●Sound ● Auto ► ● Balance 1 AUDIO OK : Off ► ● Auto 50 Game • You can also adjust Sound Mode in the Q. Menu. Select Sound Mode. Select Standard, Music, Cinema, Sport or Game. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 98 Sound Setting Adjustment -User Mode AUDIO Move Volume ● Clear Voice II : Off ● Auto 3 4 Standard(User) :: Standard Voice II : Off 3 L R Standard(User) 0 Standard ● Balance R OK Music Sound Mode Mode ●●Sound Standard(User) :: Standard • Infinite Sound : Off • Treble 50 • Infinite Sound : OffCinema • Treble 50 Sport • Bass 50 • Bass • Reset • Reset 50 Game Select AUDIO. Select Sound Mode. Select Standard, Music, Cinema, Sport or Game. Select Treble or Bass. Set the desired sound level. sound & language control 5 Sound Mode Mode ●●Sound L Move : Off ► 3 0 ► 2 Volume ● Clear ● Balance 1 AUDIO OK : Off ► ● Auto • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 99 sound & language control Infinite Sound Select this option to sound realistic. 1 2 3 Select AUDIO. Select Infinite Sound. Infinite Sound : Infinite Sound is a patented LG proprietary sound processing technology that strives immersive 5.1 surround sound impression with front two loudspeakers. Select On or Off. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. sound & language control 100 Balance You can adjust the sound balance of the speakers to preferred levels. AUDIO Volume ● Clear Voice II : Off : Off 1 3 Volume ● Clear 00 L R Move Voice II : Off : Off ●● Balance Balance Mode OK 3 0●0LBalance : Standard ● Sound • Infinite Sound : Off : Standard • Infinite Sound : Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 • Reset • Reset R 0◄ L R ► Close Select AUDIO. Select Balance. Make desired adjustment. sound & language control 2 Mode ● Auto 3 ► ●● Balance Balance ● Sound AUDIO OK ► ● Auto Move • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 101 sound & language control DTV Audio Setting (in digital mode only) When different audio types exist in an input signal, this function allows you to select the audio type you want. AUDIO ● Sound Move Mode AUDIO OK : Standard ● Sound Move Mode OK : Standard • Infinite Sound : Off • Infinite Sound : Off • Treble 50 • Treble • Bass 50 • Bass 50 • Reset • Reset Auto Auto : PCM ● Digital Audio : PCM HE-AAC Auto : :Auto ● DTV Audio Setting Auto : :Auto Dolby Digital+ Out DTVAudio AudioSetting Setting ●●DTV Out 50 ► ● Digital Audio ► Dolby Digital MPEG 1 2 sound & language control 102 3 Select AUDIO. Select DTV Audio Setting. Select Auto, HE-AAC, Dolby Digital +, Dolby Digital or MPEG. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. •Auto: Automatically outputs in the order HE-AAC > Dolby Digital+ > Dolby Digital > MPEG. (Except for Italy) Auto: Automatically outputs in the order HE-AAC > Dolby Digital+ > MPEG > Dolby Digital. (Only Italy) •HE-AAC, Dolby Digital+, Dolby Digital, MPEG: Allows users to select the audio type they want. ex) If MPEG is selected, MPEG is always outputted. If MPEG is not supported, another audio type is set in that order. • Refer to p. 109 to 110 (Audio Language Selection) Selecting Digital Audio out This function allows you to select your preferred Digital Audio Output. When Dolby Digital is available, selecting Auto in the Digital Audio Out menu will set SPDIF(Sony Philips Digital InterFace) output to Dolby Digital. If Auto is selected in the digital audio out menu when Dolby Digital is not available, SPDIF output will be PCM(Pulse-code modulation). Even if both Dolby Digital and Audio language have been set in a channel which broadcast Dolby Digital Audio, only Dolby Digital will be played. Move Mode • Infinite Sound : Off • Treble 50 • Bass 50 • Reset ● DTV Audio 1 3 : :PCM PCM ● Sound • Infinite Sound : Off • Treble 50 • Bass 50 • Reset ● DTV Audio Out OK : Standard ● Digital Audio Setting : Auto : :PCM PCM Setting : Auto Auto PCM PCM Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Select AUDIO. Select Digital Audio Out. Select Auto or PCM. Move Mode • There is a possibility that when HDMI mode, some DVD players do not make SPDIF sound. At that time, set the output of the digital audio of the DVD player to PCM. (In HDMI, Dolby Digital Plus is not supported). Item Audio Input Digital Audio output Auto(Speaker On) MPEG Dolby Digital Dolby Digital Plus HE-AAC PCM Dolby Digital Dolby Digital PCM Auto(Speaker Off) MPEG Dolby Digital Dolby Digital Plus HE-AAC PCM Dolby Digital Dolby Digital Dolby Digital PCM All PCM sound & language control 2 Out AUDIO ► ● Digital Audio OK : Standard ► ● Sound ► AUDIO • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 103 sound & language control Audio Reset Settings of the selected Sound Mode return to the default factory settings. AUDIO Mode ● Sound • Infinite Sound : Off • Infinite Sound : Off • Treble 50 • Treble ? 50 settings will be resetted. All audio • Bass 50 • Bass 50 Continue? ● DTV Audio sound & language control 3 4 ► • Reset Out : PCM Setting : Auto Mode OK : Standard ● Digital Audio 2 Move 1 AUDIO OK ► ● Sound Move • Reset ● Digital Audio ● DTV Audio : Standard Out : PCM Yes No Setting : Auto Select AUDIO. Select Reset. Select Yes. Initialize the adjusted value. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 104 Audio Description (In digital mode only) This function is for the blind, and provides explanatory audio describing the current situation in a TV programme in addition to the basic audio. When Audio Description On is selected, basic audio and Audio Description are provided only for those programmes that have Audio Description included. Volume Beep Changes the Audio Description volume Beeps when a programme with Audio Description information is selected OPTION ● Demo Mode Move Move ● Country ► : UK ID ► ● Set : UK ● Disability Assistance Indicator ● Power Reset ● Set ID ) Hard of Hearing( Reset Off Audio Description • Volume Indicator ● Factory :1 OK : Off ● Language(Language) ● Factory ◄ 0 • Beep :1 On - ► + Off Close Select OPTION. Select Disability Assistance. Select Audio Description. Adjustment for Audio Description Volume With selecting On 4 5 Select Volume or Beep. Make desired adjustment. sound & language control 3 Mode ● Country ● Power 2 ● Demo ● Language(Language) ● Disability Assistance 1 OPTION OK : Off • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 105 sound & language control I/II Stereo/Dual Reception (In Analogue Mode Only) When a programme is selected, the sound information for the station appears with the programme number and station name. 1 Select Audio or Audio Language. 2 Select the sound output. Broadcast MONO Stereo STEREO Dual sound & language control 106 On Screen Display Mono DUAL I, DUAL II, DUAL I+II ■■ Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved. ■■ Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II. DUAL ISends the primary broadcast language to the loudspeakers. DUAL IISends the secondary broadcast language to the loudspeakers. DUAL I+II Sends a separate language to each loudspeaker. NICAM Reception (In Analogue Mode Only) If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of broadcast received. 1 When NICAM mono is received, you can select NICAM MONO or FM MONO. 2 When NICAM stereo is received, you can select NICAM STEREO or FM MONO. If the stereo signal is weak, switch to FM MONO. 3 When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II or NICAM DUAL I+II or FM MONO. In AV, Component, RGB and HDMI mode, you can select output sound for the left and right loudspeakers. Select the sound output. L+R: Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio R input is sent to the right loudspeaker. L+L: Audio signal from audio L input is sent to left and right loudspeakers. R+R: Audio signal from audio R input is sent to left and right loudspeakers. sound & language control Speaker Sound Output Selection 107 sound & language control On-Screen Menu Language / Country Selection The installation guide menu appears on the TV screen when it is switched on for the first time. 1 Select your desired language. 2 Select your country. * If you want to change Language/ Country selection 1 2 Select Language(Language). 3 Select Menu Language. 4 sound & language control 108 5 1 Select OPTION. Select your desired language. Save. Select OPTION. 2 Select Country. 3 Select your country. 4 5 Select Yes or No. Save. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. NOTE ►►If you do not finish the set-up Installation Guide by pressing BACK or if you time out on the OSD (On Screen Display) the installation menu will continuously appear until the set up is completed whenever the TV is switched on. ►►If you select the wrong local country, teletext may not appear correctly on the screen and some problems may occur during teletext operation. ►►The CI (Common Interface) function may not be applied based on country broadcasting circumstances. ►►DTV mode control buttons may not function based on country broadcasting circumstances. ►►In country that Digital broadcasting regulation isn’t fixed, some DTV function may not work depending on digital broadcasting circumstances. ►►The Country Setting "UK" should only be activated in UK. ►►If the country setting is set to "--", European terrestrial digital standard broadcasting programmes are available, but some DTV functions may not work properly. Language Selection The Audio function allows selection of a preferred language. If audio data in a selected language is not broadcast, the default language audio will be played. Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a selected language is not broadcast, the default language subtitle will be displayed. When the languages you selected as the primary for Audio Language and Subtitle Language and Text Language are not supported, you can select language in secondary category. In Digital mode, use the Text language function when two or more Text languages are broadcast. If teletext data in a selected language is not broadcast, the default Text language page will be displayed. 1 2 Select Language(Language). 3 Select Audio Language, Subtitle Language or Text Language(Except for UK). 4 Select your desired language. 2 3 4 Select OPTION. Select Disability Assistance. Select Hard of Hearing( ). Select On or Off. Save. • Press the BACK button to move to the previous menu screen. sound & language control 5 1 Select OPTION. 109 sound & language control Audio Language OSD Information < Audio Language Selection > ►►When two or more audio languages are broadcast, you can select the audio language. Display N.A Status Not Available MPEG Audio Dolby Digital Audio Audio for “Visual Impaired” 1 2 Audio for “Hearing Impaired” Select Audio or Audio Language. Dolby Digital Plus Audio HE-AAC HE-AAC Audio Select an audio language. < Subtitle Language Selection > ►►When two or more subtitle languages are broadcast, you can select the subtitle language with the SUBTITLE button on the remote control. ►►Press the button to select a subtitle language. Subtitle Language OSD Information Display N.A Status Not Available Teletext Subtitle Subtitle for “Hard of Hearing” - The audio/subtitles can be displayed in a simpler form with 1 to 3 characters broadcast by the service provider. - When you select supplementary Audio (Audio for “Visual/Hearing Impaired”) the TV may output a part of the Main audio. sound & language control 110 Time Setting Clock Setup The clock is set automatically when receiving a digital signal in Auto mode. You can set the clock manually in Manual mode. You must set the time correctly before using on/off timer function. The TV time is set by the time offset information based on Time Zone and GMT (Greenwich Mean Time) which is received with the broadcast signal and the time is set automatically by a digital signal. When if the city name in Time Zone is changed into offset, you can change time by 1 hour. Time Zone menu can be changed in Auto mode. TIME Move TIME OK Move ● Clock ► ● Clock ● Off Time : Off ● Off Time ● On Time : Off ● On Time : Off ● Sleep : Off ● Alarm ● Sleep Timer ● Alarm Timer ◄Move : Off Date : Off Month : Off Year : Off OK OK ► Auto 3 Mar. 2008 Hour 16 Minute 09 Time Zone London GMT Close 1 3 4 5 Select Clock. Select Auto or Manual. time setting 2 Select TIME. Select either the year, month, date, time or Time Zone option. Set the year, month, date, time or Time Zone option. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 111 time setting Auto on/off time setting The Off time function automatically switches the TV to standby at a preset time. The Off time function overrides the On time function if both are set to the same time. The TV must be in standby mode for the On time to work. TIME Move TIME OK ● Clock ● Clock Time : Off ● Off ● On Time : Off ● On Time ● Sleep : Off ● Sleep : Off ● Alarm ► Timer ● Alarm ► ● Off Move Time Timer OK 1 Mar. 2007 16:09 : Off Repeat ◄ Off : Off Hour 00 : Off Minute 00 : Off Input ► Antenna Programme TV1 Volume 30 Close 1 2 time setting 3 4 5 6 •T o cancel On/Off Time function, select Off. Select TIME. •F or On Time function only Select Off Time or On Time. 2 Select Repeat. Select Off, Once, Daily, Mon. ~ Fri., Mon. ~ Sat., Sat. ~ Sun. or Sun.. Set the hour. 1 3 4 Select Input. Select the input source. Set the programme. Adjust volume level at switch-on. Set the minutes. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 112 Sleep Timer setting You do not have to remember to switch the TV off before you go to sleep. The sleep timer automatically switches the TV to standby after the preset time has elapsed. 1 Select Sleep Timer. 2 Select Off, 10, 20, 30, 60, 90, 120, 180 or 240 min. •W hen you switch the TV off, the preset sleep timer is cancelled. •Y ou can also adjust Sleep Timer in the TIME menu. Alarm Setting The alarm sound will go off when the designated time passes. When 60 seconds pass, the alarm sound will stop. If you do not want Alarm function, select “Off” TIME Move TIME OK ● Clock Move OK ● Clock 1 Mar. 2007 16:09 Time : Off ● Off Time : Off ● On Time : Off ● On Time : Off Alarm : Off ● Sleep : Off Hour : Off 00 Minute 00 ● Sleep Timer : Off ► ● Alarm ► ● Off Timer ● Alarm ◄ Off ► 1 2 3 4 5 Select TIME. Select Alarm. • When alarm operates in standby mode, press the any button to stop alarm. time setting Close • When alarm operates in power on mode, press the OK button to stop alarm. Select On. Set the hour. Set the minutes. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. 113 Parental Control / Ratings Set Password & Lock System Enter the password, press ‘0’,‘0’,‘0’,‘0’ on the remote control handset. When France is selected for Country, password is not ‘0’,‘0’,‘0’,‘0’ but ‘1’,’2’,’3’,’4’. When France is selected for Country, password cannot be set as ‘0’,‘0’,‘0’,‘0’ . If a channel is locked, enter the password to unlock it temporarily. LOCK ● Set ● Block ● Parental 3 parental control / ratings 114 4 5 ► ● Input ► : :Off Off Lock LOCK Programme Guidance: Blocking Off Block : :Off Off ● Block ● Parental ● Input ● Key Select LOCK. OK Off Off ● Lock System : Off Move Password Lock Programme ► ● Lock System ● Key 2 OK ● Set 1 Move Password On Guidance: Blocking Off Block : Off • If you forget your password, press ‘0’, ‘3’, ‘2’, ‘5’ on the remote control handset. Select Lock System. Select On. Set the password. Input a 4-digit password. Be sure to remember this number! Re-enter new password for confirm. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. Block Programme Blocks any programme that you do not want to watch or that you do not want your children to watch. It is available to use this function in Lock System ”On”. Enter a password to watch a blocked programme. Programme Edit LOCK ● Set Move System : On ● Block ● Parental ● Input ● Key TV OK Password ● Lock Lock Page 1/2 Programme ▲ ▼ Guidance: Blocking Off Block : Off 1 YLE TV1 (D) 2 YLE TV2 (D) 3 YLE FST (D) 4 YLE24 (D) 5 YLE Teema (D) 6 YLE PEILI (R) 7 YLEQ (R) 8 YLEN KLASSINEN (R) 9 YLE FSR+ (R) 10 YLEMONDO (R) 11 YLE X3M (R) 12 TV4 Stockholm (D) 13 Kanal Lokal (D) 14 CNN (D) 15 TV4 (D) 15 TV4 Plus (D) 17 TV400 (D) 18 TV4 Film (D) 19 TV4 Fakta (D) 20 MediaCorp HD5 (D) 21 Dolby D 5.1 Demo (R) ▼ Pr. Change Navigation P Page Change Previous Block/Unblock 1 Select LOCK. 2 3 5 Enter the Block Progra mme. Enter the Block Programme. YELLOW Select a programme to be locked. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. parental control / ratings 4 Select Lock System. 115 parental control / ratings Parental Control (In Digital Mode only) This function operates according to information from the broadcasting station. Therefore if the signal has incorrect information, this function does not operate. A password is required to gain access to this menu. This set is programmed to remember which option it was last set to even if you switch the set off. Prevents children from watching certain adult’s TV programmes, according to the ratings limit set. Enter a password to watch a blocked programme. Rating differs by country. LOCK ● Set Move Password ● Lock System ● Set : On ● Block ●● Parental Parental Guidance Guidance:: Blocking Blocking Off Off ● Input Lock Programme ▲ ▼ Block : Off Move System : On OK Blocking Off : Permits all programmes ▲ Password ● Lock ● Key LOCK OK Programme 12 and above 13 and above ● Block ●● Parental Parental Guidance Guidance:: Blocking Blocking Off Off ● Input ● Key Lock : Off Block 14 and above 12 and above ▲ ▼ parental control / ratings 116 3 4 14 and above 15 and above 16 and above 16 and above 17 and above 17 and above 18 and above 18 and above Blocking Off (Except for France) 2 13 and above 15 and above 1 Programmes for 18 and above will be blocked ▲ (Only France) Select LOCK. Select Lock System. Select Parental Guidance. Make appropriate adjustments. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. External Input Blocking Enables you to block an input. It is available to use this function in Lock System ”On”. ■■ Image shown may differ from your TV. LOCK ● Set Move Password ● Lock System ● Set : On ● Block ● Parental ● Input Lock Programme Guidance: Blocking Off Block ▲ ▼ : Off Move System : On ● AV Programme ● Block ● Parental ● Input ● Key OK Password ● Lock ● Key LOCK OK Lock : Off ◄ Guidance : Blocking Off ● Component Block ► Off ● RGB ● HDMI1 Off Off ▲ ▼ ● HDMI2 Off Off Close 1 2 3 5 Select Lock System. Select Input Block. Select input source. Select On or Off. • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. parental control / ratings 4 Select LOCK. 117 parental control / ratings Key Lock This feature can be used to prevent unauthorized viewing by locking out the front panel controls, so that it can only be used with the remote control. This TV is programmed to remember which option it was last set to even if you turn the TV off. LOCK ● Lock 2 3 parental control / ratings 118 LOCK OK System ● Set : Off ● Lock ● Block Programme ● Parental ● Input ● Key Lock ● Key Lock : Off Guidance: Blocking Off Block Select LOCK. Select Key Lock. Select On or Off. Move OK Password System : Off ● Block ● Parental Programme ● Input Lock ● Key Lock : Off : Off Guidance: Blocking Off Block Off Off ► 1 Move Password ► ● Set On • In Key Lock ‘On’, if the TV is turned off, press the / I, INPUT, P (or P ▲▼ ) button on the TV or or NUMBER buttons on the POWER, INPUT, P remote control then the set will be turned on. • With the Key Lock On, the display ‘ Key Lock On ’ appears on the screen if any button on the front panel is pressed while viewing the TV. • When another OSD is displayed, will not operate. ‘ Key Lock On ’ • Press the MENU/EXIT button to return to normal TV viewing. • Press the BACK button to move to the previous menu screen. Teletext This feature is not available in all countries. Teletext is a free service broadcast by most TV stations which gives up-to-theminute information on news, weather, television programmes, share prices and many other topics. ■■ Image shown may differ from your TV. ENERGY AV MODE INPUT TV/ RAD SAVING The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information. 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW MARK RATIO Switch on/off Press the TEXT button to switch to teletext. The initial page or last page viewed appears on the screen. Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the TEXT button to switch off teletext. The previous mode reappears. P P A G E MUTE GUIDE PORTAL INFO OK MENU BACK EXIT AD SIMPLE Text ■■ Page selection Enter 1 the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. 2 The P button can be used to select the preceding or following page. teletext 119 teletext TOP Text The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block. ■■ Block / group / page selection 1 With the blue button you can progress from block to block. 2 Use the yellow button to proceed to the next group with automatic overflow to the next block. 3 With the green button you can proceed to the next existing page with automatic overflow to the next group. button can be used. 4 Alternatively the P The red button returns to the previous selection. Alternatively the P button can be used. ■■ Direct page selection As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode. Fastext The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button. ■■Page selection 1 2 teletext 120 3 4 Press the T.OPT button and then use button to select menu. Display the index page. You can select the pages which are colour coded along the bottom line with corresponding coloured buttons. AS with SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode. The P button can be used to select the preceding or following page. Special Teletext Functions ■■ Press the T. OPT button and then use button to select the Text Option menu. In UK(In digital mode), T. OPT button does not work. ■■Index Text Option Select the each index page. Index Time Hold ■■Time Reveal Update When viewing a TV programme, select this menu to display the time at the top right Close hand corner of the screen. In the teletext mode, press this button to select a sub page number. The sub page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN,< > or NUMBER buttons. ■■ Hold Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this menu is selected the stop symbol is displayed at the top left-hand corner of the screen and the automatic page change is inactive. ■■Reveal Select this menu to display concealed information, such as solutions to riddles or puzzles. ■■Update Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at the top left hand corner of the screen. When the updated page is available then display will change to the page number. Select this menu again to view the updated teletext page. teletext 121 Digital Teletext *This function works in UK, Ireland only. The TV gives you access to digital teletext which is greatly improved in various aspects such as text, graphics etc. This digital teletext can access special digital teletext services and specific services which broadcast digital teletext. Teletext within Digital Service 1 Press the numeric or P button to select a digital service which broadcasts digital teletext. 2 Follow the indications on digital teletext and move onto the next step by pressing TEXT, OK, , RED, GREEN, YELLOW, BLUE or NUMBER buttons and etc.. 3 To change digital teletext service, select a different service by the numeric or P button. Teletext in Digital Service digital teletext 122 1 Press the numeric or P button to select a certain service which broadcasts digital teletext. 2 Press the TEXT or coloured button to switch on teletext. 3 Follow the indications on digital teletext and move onto the next step by pressing OK, , RED, GREEN, YELLOW, BLUE or NUMBER buttons and so on. 4 Press the TEXT or colour button to switch off digital teletext and return to TV viewing. Some services may allow you to access text services by pressing the RED button. Appendix Troubleshooting The TV does not operate properly. The remote control does not work Power is suddenly turned off ■■ Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control directly at the TV. ■■ Ensure that the batteries are installed with correct polarity (+ to +, - to -). ■■ Install new batteries. ■■ Is the sleep timer set? ■■ Check the power control settings. Has the Power supply been interrupted. The video function does not work. ■■ Check whether the TV is switched on. ■■ Try another channel. The problem may be with the broadcast. No picture & No sound ■■ Is the power cord inserted correctly into the mains? ■■ Check your antenna direction and/or location. ■■ Test the mains outlet by plugging another TV into the same outlet. Picture appears slowly ■■ This is normal, the image is muted during the TV startup process. Please contact your service centre, if the picture has not appeared after five minutes. after switching on ■■ Adjust Colour in menu option. No or poor colour or poor picture ■■ Allow a sufficient distance between the TV and the VCR. ■■ Try another channel. The problem may be with the broadcast. ■■ Are the video cables installed properly? ■■ Activate any function to restore the brightness of the picture. Horizontal/vertical bars or picture shaking Poor reception on some channels Lines or streaks when connecting HDMI ■■ Station or cable channel experiencing problems, tune to another station. ■■ Station signal is weak, reposition the antenna to receive weaker stations. ■■ Check for sources of possible interference. ■■ Check antenna (Change the position of the antenna). ■■ Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are not High Speed HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable. appendix in pictures No picture ■■ Check for local interference such as an electrical appliance or power tool. 123 appendix The audio function does not work. Picture OK & No sound No output from one of the speakers Unusual sound from inside the TV No sound when connecting HDMI or USB ■■ Press the + or - button. ■■ Sound muted? Press MUTE button. ■■ Try another channel. The problem may be with the broadcast. ■■ Are the audio cables installed properly? ■■ Adjust Balance in menu option. ■■ A change in ambient humidity or temperature may result in an unusual noise when the TV is switched on or off and does not indicate a fault with the TV. ■■ Check HDMI cable is High Speed HDMI Cable. ■■ Check USB cable over version 2.0. *This feature is not available for all models. There is a problem in PC mode. (Only PC mode applied) The signal is out of range (Invalid format) Vertical bar or stripe on background & Horizontal Noise & Incorrect position Screen colour is unstable or single colour appendix 124 ■■ Adjust resolution, horizontal frequency, or vertical frequency. ■■ Check the input source. ■■ Use Auto configure or adjust clock, phase, or H/V position. (Option) ■■ Check the signal cable. ■■ Reinstall the PC video card. Maintenance Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it to wipe the screen. 2 Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on. Cleaning the Cabinet ■■ To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. ■■ Do not to use a wet cloth. Extended Absence CAUTION ►►If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to protect against possible damage from lightning or power surges. appendix 125 appendix Product Specifications 22LD3*** 26LD3*** 22LD320H-ZA 26LD320H-ZA 26LD322H-ZA with stand 533.4mmx 397.0mmx 171.0 mm 667.0 mm x 504.0 mm x 224.0 mm without stand 533.4mmx 351.7mmx 65.0 mm 667.0 mm x 446.2 mm x 80.0 mm with stand without stand 4.8 kg 4.6 kg 8.9 kg 7.8 kg MODELS Dimensions (Width x Height x Depth) Weight Power requirement AC 100-240 V~ 50 / 60 Hz 50 W Power Consumption 32LD3*** 37LD3*** 32LD320H-ZA 32LD322H-ZA 37LD322H-ZA with stand 805.0 mm x 583.0 mm x 224.0 mm 922.0 mm x 659.0 mm x 297.0 mm without stand 805.0 mm x 528.0 mm x 79.9 mm 922.0 mm x 595.0 mm x 88.0 mm with stand without stand 11.5 kg 10.3 kg 14.8 kg 13.0 kg AC 100-240 V~ 50 / 60 Hz 120 W AC 100-240 V~ 50 / 60 Hz 180 W MODELS Dimensions (Width x Height x Depth) Weight Power requirement Power Consumption CI Module Size 100.0 mm x 55.0 mm x 5.0 mm (Width x Height x Depth) Operating Temperature Environment condition AC 100-240 V~ 50 / 60 Hz 100 W 0 °C to 40 °C Less than 80 % Operating Humidity Storage Temperature -20 °C to 60 °C Storage Humidity Less than 85 % Supported movie files Refer to p. 46 to 47 ■■ The specifications shown above may be changed without prior notice for quality improvement. appendix Television System Programme Coverage Digital TV Analogue TV DVB-T PAL/SECAM B/G/D/K, PAL I/II, DVB-C SECAM L/L’ VHF, UHF Maximum number of storable programme External Antenna Impedance VHF: E2 to E12, UHF: E21 to E69, CATV: S1 to S20, HYPER: S21 to S47 500 75 Ω ■■ The specifications shown above may be changed without prior notice for quality improvement. 126 75 Ω IR Codes *This feature is not available for all models. Code (Hexa) Function Note 95 Energy Saving R/C BUTTON 08 POWER R/C BUTTON(POWER ON/OFF) 0B INPUT R/C BUTTON 79 RATIO R/C BUTTON F0 TV/RAD R/C BUTTON 45 Q.MENU R/C BUTTON 43 MENU R/C BUTTON AB GUIDE R/C BUTTON 40 Up ( R/C BUTTON 41 Down ( 07 Left ( 06 Right ( 44 OK( ) R/C BUTTON 28 BACK R/C BUTTON ) ) R/C BUTTON R/C BUTTON ) ) R/C BUTTON 5B EXIT R/C BUTTON AA INFO i R/C BUTTON 30 AV MODE R/C BUTTON 02 + R/C BUTTON 03 - R/C BUTTON 1E MARK R/C BUTTON OC PORTAL R/C BUTTON 09 MUTE R/C BUTTON 00 P R/C BUTTON 01 P R/C BUTTON Number Key 0 to 9 R/C BUTTON 10 to 19 LIST R/C BUTTON Q.VIEW R/C BUTTON 72 RED Key R/C BUTTON 71 GREEN Key R/C BUTTON 63 YELLOW Key R/C BUTTON 61 BLUE Key R/C BUTTON 20 TEXT R/C BUTTON 21 T.OPT(T.Option) R/C BUTTON 39 SUBTITLE R/C BUTTON 7E SIMPLINK R/C BUTTON 91 AD R/C BUTTON E8 ALARM R/C BUTTON B1 ▀ R/C BUTTON B0 ► R/C BUTTON BA ll R/C BUTTON 8F ◄◄ R/C BUTTON 8E ►► R/C BUTTON appendix 53 1A 127 appendix External Control Device Setup RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the product. Type of Connector; D-Sub 9-Pin Male No. 1 2 3 4 5 6 7 8 9 Pin Name No connection RX RS232 TX RS232 IR from TV GND No connection +5V No connection +12V 1 5 6 9 RS-232C Configurations 7-Wire Configurations (Standard RS-232C cable) appendix 128 3-Wire Configurations(Not standard) PC TV PC TV 2 3 5 4 6 7 8 3 2 5 6 4 8 7 2 3 5 4 6 7 8 3 2 5 6 4 7 8 D-Sub 9 D-Sub 9 D-Sub 9 D-Sub 9 Set ID Use this function to specify a set ID number. Refer to ‘Real Data Mapping’. ► p.133. OPTION ● Demo Mode Mode Move ● Country ● Disability Assistance ● Disability Assistance ● Power ● Power Indicator ::11 : UK Indicator ● Factory ► Reset ◄ Reset ● Set ID OK : Off ● Language(Language) : UK ► 3 ● Demo ● Country ● Set ID 2 OPTION OK ● Language(Language) ● Factory 1 Move : Off ::11 1 ► Close Select OPTION. Select Set ID. Adjust Set ID to choose the desired TV ID number. The adjustment range of SET ID is 1 to 99. appendix • Press the BACK button to move to the previous menu screen. 129 appendix Communication Parameters ■■ Baud rate : 9600 bps (UART) ■■ Data length : 8 bits ■■ Parity : None ■■ Stop bit : 1 bit ■■ Communication code : ASCII code ■■ Use a crossed (reverse) cable. Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] Command Reference List COMMAND COMMAND 1 2 01. Power appendix 130 k DATA (Hexadecimal) a 00 to 01 * [Command 1] : First command to control the TV. (j, k, m or x) * [Command 2] : Second command to control the TV. : You can adjust the set ID to choose * [Set ID] desired monitor ID number in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled. Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on transmission/receiving protocol. : To transmit command data. * [DATA] Transmit ‘FF’ data to read status of command. : Carriage Return * [Cr] ASCII code ‘0x0D’ : ASCII code ‘space (0x20)’ * [ ] 02. Aspect Ratio k c Refer to p. 131 03. Screen Mute k d Refer to p. 131 04. Volume Mute k e 00 to 01 05. Volume Control k f 00 to 64 06. Contrast k g 00 to 64 07. Brightness k h 00 to 64 08. Colour k i 00 to 64 09. Tint k j 00 to 64 10. Sharpness k k 00 to 64 11. OSD Select k l 00 to 01 12. Remote control lock mode k m 00 to 01 13. Treble k r 00 to 64 14. Bass k s 00 to 64 OK Acknowledgement 15. Balance k t 00 to 64 [Command2][ ][Set ID][ ][OK][Data][x] 16. Colour Temperature x u 00 to 64 17. Energy Saving j q 00 to 05 18. Auto Configuration j u 01 19. Tune Command m a Refer to p. 133 * The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. 20. Programme Add/Skip m b 00 to 1 21. Key m c Key Code 22. Control Back Light m g 00 to 64 23. Input select (Main) x b Refer to p. 134 Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from * Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are not exe- non-viable functions or communication errors. cuted and treated as NG. Data00: Illegal Code 01. Power (Command: k a) ►► To control Power On/Off of the set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data00 : Power Off Ack 01 : Power On [a][ ][Set ID][ ][OK/NG][Data][x] ►► To show Power On/Off. Transmission ►► To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data00 : Volume mute on (Volume off) 01 : Volume mute off (Volume on) Ack [e][ ][Set ID][ ][OK/NG][Data][x] [k][a][ ][Set ID][ ][FF][Cr] 05. Volume Control (Command: k f) Ack [a][ ][Set ID][ ][OK/NG][Data][x] * Similarly, if other functions transmit ‘0xFF’ data based on this format, Acknowledgement data feed back presents status about each function. * OK Ack., Error Ack. and other message may display on the screen when TV is power On. 02. Aspect Ratio (Command: k c) (Main Picture Size) ►► To adjust the screen format. (Main picture format) You can also adjust the screen format using the Aspect Ratio in the Q.MENU. or PICTURE menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 01 : Normal screen (4:3) 02 : Wide screen (16:9) 04 : Zoom 06 : Original Ack 04. Volume Mute (Command: k e) 07 : 14:9 09 : Just Scan 0B : Full Wide 10 to 1F : Cinema Zoom 1 to 16 [c][ ][Set ID][ ][OK/NG][Data][x] * Using the PC input, you select either 16:9 or 4:3 screen aspect ratio. * In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p 24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i, 1080p 50 Hz / 60 Hz) mode, Just Scan is available. * Full Wide is supported only for Digital, Analogue, AV. 03. Screen Mute (Command: k d) ►► To select screen mute on/off. Transmission Ack [d][ ][Set ID][ ][OK/NG][Data][x] * In case of video mute on only, TV will display On Screen Display(OSD). But, in case of Screen mute on, TV will not display OSD. [k][f][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack [f][ ][Set ID][ ][OK/NG][Data][x] 06. Contrast (Command: k g) ►► To adjust screen contrast. You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack [g][ ][Set ID][ ][OK/NG][Data][x] 07. Brightness (Command: k h) ►► To adjust screen brightness. You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack [h][ ][Set ID][ ][OK/NG][Data][x] 08. Colour (Command: k i) ►► To adjust the screen colour. You can also adjust colour in the PICTURE menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack appendix [k][d][ ][Set ID][ ][Data][Cr] Data00 : Screen mute off (Picture on) Video mute off 01 : Screen mute on (Picture off) 10 : Video mute on ►► To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission [i][ ][Set ID][ ][OK/NG][Data][x] 131 appendix 09. Tint (Command: k j) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. Transmission 13. Treble (Command: k r) ►► To adjust treble. You can also adjust treble in the AUDIO menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] [k][r][ ][Set ID][ ][Data][Cr] DataRed : 00 to Green : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. [j][ ][Set ID][ ][OK/NG][Data][x] 10. Sharpness (Command: k k) ►► To adjust the screen sharpness. You can also adjust sharpness in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133.. Ack [k][ ][Set ID][ ][OK/NG][Data][x] Ack [r][ ][Set ID][ ][OK/NG][Data][x] 14. Bass (Command: k s) ►► To adjust bass. You can also adjust bass in the AUDIO menu. Transmission [k][s][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack [s][ ][Set ID][ ][OK/NG][Data][x] 15. Balance (Command: k t) 11. OSD Select (Command: k l) ►► To select OSD (On Screen Display) on/off when controlling remotely. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 00 : OSD off Ack 01 : OSD on ►► To adjust balance. You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack [t][ ][Set ID][ ][OK/NG][Data][x] [l][ ][Set ID][ ][OK/NG][Data][x] 16. Colour Temperature (Command: x u) 12. Remote control lock mode (Command: k m) ►► To lock the front panel controls on the monitor and remote control. Transmission [k][m][ ][Set ID][ ][Data][Cr] appendix 132 Data00 : Lock off Ack 01 : Lock on [m][ ][Set ID][ ][OK/NG][Data][x] * If you are not using the remote control, use this mode. When main power is on/off, external control lock is released. * In the standby mode, if key lock is on, TV will not turn on by power on key of IR & Local Key. ►► To adjust colour temperature. You can also adjust Colour Temperature in the PICTURE menu. Transmission [x][u][ ][Set ID][ ][Data][Cr] DataMin : 00 to Max : 64 * Refer to ‘Real data mapping 1’. See page 133. Ack [u][ ][Set ID][ ][OK/NG][Data][x] 17. Energy Saving (Command: j q) 19.Tune Command (Command: m a) ►► To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu. Transmission ►► Select channel to following physical number. Transmission [j][q][ ][Set ID][ ][Data][Cr] Data00 :High channel data Data01 :Low channel data ex. No. 47 -> 00 2F (2FH) No. 394 -> 01 8A (18AH), DTV No. 0 -> Don’t care Data02 :0x00 : Analogue Main 0x10 : DTV Main 0x20 : Radio Channel data range Analogue - Min: 00 to Max: 63 (0 to 99) Digital - Min: 00 to Max: 3E7 (0 to 999) (Except For Sweden, Finland, Norway, Denmark, Ireland) Digital - Min: 00 to Max: 270F (0 to 9999) (Only Sweden, Finland, Norway, Denmark, Ireland) Power Saving Function Level Description 7 6 5 4 3 2 1 0 0 0 0 0 Low Power 0 0 0 0 Off 0 0 0 0 Low Power 0 0 0 1 Minimum 0 0 0 0 Low Power 0 0 1 0 Medium 0 0 0 0 Low Power 0 0 1 1 Maximum 0 0 0 0 Low Power 0 1 0 1 Screen Off Ack [q][ ][Set ID][ ][OK/NG][Data][x] [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr] Ack [a][ ][Set ID][ ][OK/NG][Data][x] DataMin: 00 to Max: 7DH 18. Auto Configure(Command: j u) ►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data01: To set Ack [u][ ][Set ID][ ][OK/NG][Data][x] 20. Programme Add/Skip(Command: m b) ►► To set skip status for the current Programme. Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 00 : Skip 01 : Add Ack [b][ ][Set ID][ ][OK/NG][Data][x] * Real data mapping 1 00 : Step 0 A: Step 10 (Set ID 10) F: 10 : Step 15 (Set ID 15) Step 16 (Set ID 16) 64 : Step 100 6E : Step 110 Step 115 Step 116 CF : Step 199 FE : Step 254 FF : Step 255 appendix 73 : 74 : 133 appendix 21. Key(Command: m c) ►► To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] DataKey code - Refer to page 127. Ack [c][ ][Set ID][ ][OK/NG][Data][x] 23. Input select (Command: x b) (Main Picture Input) ►► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] DataStructure MSB 0 LSB 0 0 0 External Input External Input 22. Control Back Light (Command: m g) 0 0 Input Number Data 0 0 0 0 DTV 0 0 0 1 ►► To Control the back light. Transmission Analogue 0 0 1 0 AV 0 1 0 0 [m][g][ ][Set ID][ ][Data][Cr] Component 0 1 1 0 Data: data Min: 00 to Max: 64 RGB 0 1 1 1 1 0 0 0 Ack 1 0 0 1 [g][ ][Set ID][ ][OK/NG][Data][x] 1 0 1 0 Input Number HDMI Data 0 0 0 0 Input1 0 0 0 1 Input2 0 0 1 0 Input3 0 0 1 1 Input4 Ack [b][ ][Set ID][ ][OK/NG][Data][x] appendix 134 0 0 Open source software notice The following GPL executables and LGPL, MPL libraries used in this product are subject to the GPL2.0/ LGPL2.1/MPL1.1 License Agreements: GPL EXECUTABLES: Linux kernel, busybox, e2fsprogs, gdbserver, jfsutils, lzo, mtd-utils, procps, u-boot, udhcpc LGPL LIBRARIES: directFB, glib, glibc, gconv, iconv MPL LIBRARIES: Cairo, Nanox LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of performing such distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics : [email protected] This offer is valid for a period of three (3) years from the date of the distribution of this product by LG Electronics. You can obtain a copy of the GPL, LGPL, MPL licenses on the CD-ROM provided with this product. Also you can obtain the translation of GPL, LGPL licenses from http://www.gnu.org/licenses/old-licenses/gpl-2.0-translations.html, http://www.gnu.org/licenses/old-licenses/lgpl-2.1-translations.html. This product includes ReportGUI component which is licensed under the terms of the Apache License, Version 2.0. You can obtain a copy of the Apache license from http://www.apache.org/licenses/LICENSE-2.0.html. appendix This product includes other open source software. ■■ boost C++: software developed by http://www.boost.org distributed under the Boost Software License, Version 1.0 ■■ chromium: copyright © 2008, The Chromium Authors ■■ expat: • copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper • copyright © 2001-2007 Expat maintainers. ■■ freetype: copyright © 2003 The FreeType Project (www.freetype.org). ■■ ICU: copyright © 1995-2001 International Business Machines Corporation and others. ■■ libcurl: copyright © 1996 - 2008, Daniel Stenberg. ■■ libjpeg: This software is based in part on the work of the Independent JPEG Group copyright © 1991 – 1998, Thomas G. Lane. ■■ libmng: copyright © 2000-2007 Gerard Juyn, Glenn Randers-Pehrson ■■ libpng: copyright © 1998-2008 Glenn Randers-Pehrson ■■ md5: copyright © 1991-2, RSA Data Security, Inc ■■ md5 checksum : copyright © 1999, 2000, 2002 Aladdin Enterprises ■■ ncurses: copyright © 1998 Free Software Foundation, Inc. ■■ netBSD : copyright © 1998 The NetBSD Foundation, Inc. ■■ openSSL: • cryptographic software written by Eric Young. • software written by Tim Hudson. • software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org) 135 appendix ■ pixman: • copyright © 1987, 1988, 1989, 1998 The Open Group • copyright © 1987, 1988, 1989 Digital Equipment Corporation • copyright © 1999, 2004, 2008 Keith Packard • copyright © 2000 SuSE, Inc. • copyright © 2000 Keith Packard, member of The XFree86 Project, Inc. • copyright © 2004, 2005, 2007, 2008 Red Hat, Inc. • copyright © 2004 Nicholas Miell • copyright © 2005 Lars Knoll & Zack Rusin, Trolltech • copyright © 2005 Trolltech AS • copyright © 2007 Luca Barbato • copyright © 2008 Aaron Plattner, NVIDIA Corporation • copyright © 2008 Rodrigo Kumpera • copyright © 2008 André Tupinambá • copyright © 2008 Mozilla Corporation • copyright © 2008 Frederic Plourde ■ strace : • copyright © 1991, 1992 Paul Kranenburg. • copyright © 1993 Branko Lankester. • copyright © 1993 Ulrich Pegelow. • copyright © 1995, 1996 Michael Elizabeth Chastain. • copyright © 1993, 1994, 1995, 1996 Rick Sladkey. • copyright © 1998-2003 Wichert Akkerman. • copyright © 2002-2008 Roland McGrath. • copyright © 2003-2008 Dmitry V. Levin. • copyright © 2007-2008 Jan Kratochvil. ■ tinyxml: copyright © 2000-2006 Lee Thomason ■ xyssl: • Copyright © 2006-2008 Christophe Devinee • Copyright © 2009 Paul Bakker ■ zlib: copyright © 1995-2005 Jean-loup Gailly and Mark Adler All rights reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: appendix 136 THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. Open source license GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. appendix 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". 137 appendix 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) appendix 138 The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. appendix 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. 139 appendix NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. <one line to give the program's name and a brief idea of what it does.> Copyright (C) <year> <name of author> This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names: appendix 140 Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker. <signature of Ty Coon>, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. appendix For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. 141 appendix Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you". A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".) "Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. appendix 142 (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. 4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables. When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. appendix a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) 143 appendix c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. appendix 144 It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. <one line to give the library's name and a brief idea of what it does.> Copyright (C) <year> <name of author> This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker. <signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice appendix Also add information on how to contact you by electronic and paper mail. 145 appendix MOZILLA PUBLIC LICENSE Version 1.1 --------------1. Definitions. 1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party. 1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications. 1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor, and the Modifications made by that particular Contributor. 1.3. "Covered Code" means the Original Code or Modifications or the combination of the Original Code and Modifications, in each case including portions thereof. 1.4. "Electronic Distribution Mechanism" means a mechanism generally accepted in the software development community for the electronic transfer of data. 1.5. "Executable" means Covered Code in any form other than Source Code. 1.6. "Initial Developer" means the individual or entity identified as the Initial Developer in the Source Code notice required by Exhibit A. 1.7. "Larger Work" means a work which combines Covered Code or portions thereof with code not governed by the terms of this License. 1.8. "License" means this document. 1.8.1. "Licensable" means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein. 1.9. "Modifications" means any addition to or deletion from the substance or structure of either the Original Code or any previous Modifications. When Covered Code is released as a series of files, a Modification is: A. Any addition to or deletion from the contents of a file containing Original Code or previous Modifications. B. Any new file that contains any part of the Original Code or previous Modifications. 1.10. "Original Code" means Source Code of computer software code which is described in the Source Code notice required by Exhibit A as Original Code, and which, at the time of its release under this License is not already Covered Code governed by this License. 1.10.1. "Patent Claims" means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent Licensable by grantor. 1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor's choice. The Source Code can be in a compressed or archival form, provided the appropriate decompression or de-archiving software is widely available for no charge. 1.12. "You" (or "Your") means an individual or a legal entity exercising rights under, and complying with all of the terms of, this License or a future version of this License issued under Section 6.1. For legal entities, "You" includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition, "control" means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity. appendix 146 2. Source Code License. 2.1. The Initial Developer Grant. The Initial Developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims: (a) under intellectual property rights (other than patent or trademark) Licensable by Initial Developer to use, reproduce, modify, display, perform, sublicense and distribute the Original Code (or portions thereof) with or without Modifications, and/or as part of a Larger Work; and (b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise dispose of the Original Code (or portions thereof). (c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes Original Code under the terms of this License. (d) Notwithstanding Section 2.1(b) above, no patent license is granted: 1) for code that You delete from the Original Code; 2) separate from the Original Code; or 3) for infringements caused by: i) the modification of the Original Code or ii) the combination of the Original Code with other software or devices. 2.2. Contributor Grant. Subject to third party intellectual property claims, each Contributor hereby grants You a world-wide, royalty-free, non-exclusive license (a) under intellectual property rights (other than patent or trademark) Licensable by Contributor, to use, reproduce, modify, display, perform, sublicense and distribute the Modifications created by such Contributor (or portions thereof) either on an unmodified basis, with other Modifications, as Covered Code and/or as part of a Larger Work; and (b) under Patent Claims infringed by the making, using, or selling of Modifications made by that Contributor either alone and/or in combination with its Contributor Version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) Modifications made by that Contributor (or portions thereof); and 2) the combination of Modifications made by that Contributor with its Contributor Version (or portions of such combination). (c) the licenses granted in Sections 2.2(a) and 2.2(b) are effective on the date Contributor first makes Commercial Use of the Covered Code. (d) Notwithstanding Section 2.2(b) above, no patent license is granted: 1) for any code that Contributor has deleted from the Contributor Version; 2) separate from the Contributor Version; 3) for infringements caused by: i) third party modifications of Contributor Version or ii) the combination of Modifications made by that Contributor with other software (except as part of the Contributor Version) or other devices; or 4) under Patent Claims infringed by Covered Code in the absence of Modifications made by that Contributor. 3. Distribution Obligations. 3.1. Application of License. The Modifications which You create or to which You contribute are governed by the terms of this License, including without limitation Section 2.2. The Source Code version of Covered Code may be distributed only under the terms of this License or a future version of this License released under Section 6.1, and You must include a copy of this License with every copy of the Source Code You distribute. You may not offer or impose any terms on any Source Code version that alters or restricts the applicable version of this License or the recipients' rights hereunder. However, You may include an additional document offering the additional rights described in Section 3.5. 3.2. Availability of Source Code. Any Modification which You create or to which You contribute must be made available in Source Code form under the terms of this License either on the same media as an Executable version or via an accepted Electronic Distribution Mechanism to anyone to whom you made an Executable version available; and if made available via Electronic Distribution Mechanism, must remain available for at least twelve (12) months after the date it initially became available, or at least six (6) months after a subsequent version of that particular Modification has been made available to such recipients. You are responsible for ensuring that the Source Code version remains available even if the Electronic Distribution Mechanism is maintained by a third party. 3.3. Description of Modifications. You must cause all Covered Code to which You contribute to contain a file documenting the changes You made to create that Covered Code and the date of any change. You must include a prominent statement that the Modification is derived, directly or indirectly, from Original Code provided by the Initial Developer and including the name of the Initial Developer in (a) the Source Code, and (b) in any notice in an Executable version or related documentation in which You describe the origin or ownership of the Covered Code. appendix 3.4. Intellectual Property Matters (a) Third Party Claims. If Contributor has knowledge that a license under a third party's intellectual property rights is required to exercise the rights granted by such Contributor under Sections 2.1 or 2.2, Contributor must include a text file with the Source Code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If Contributor obtains such knowledge after the Modification is made available as described in Section 3.2, Contributor shall promptly modify the LEGAL file in all copies Contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the Covered Code that new knowledge has been obtained. 147 appendix (b) Contributor APIs. If Contributor's Modifications include an application programming interface and Contributor has knowledge of patent licenses which are reasonably necessary to implement that API, Contributor must also include this information in the LEGAL file. (c) Representations. Contributor represents that, except as disclosed pursuant to Section 3.4(a) above, Contributor believes that Contributor's Modifications are Contributor's original creation(s) and/or Contributor has sufficient rights to grant the rights conveyed by this License. 3.5. Required Notices. You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a particular Source Code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more Modification(s) You may add your name as a Contributor to the notice described in Exhibit A. You must also duplicate this License in any documentation for the Source Code where You describe recipients' rights or ownership rights relating to Covered Code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of Covered Code. However, You may do so only on Your own behalf, and not on behalf of the Initial Developer or any Contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by You alone, and You hereby agree to indemnify the Initial Developer and every Contributor for any liability incurred by the Initial Developer or such Contributor as a result of warranty, support, indemnity or liability terms You offer. 3.6. Distribution of Executable Versions. You may distribute Covered Code in Executable form only if the requirements of Section 3.1-3.5 have been met for that Covered Code, and if You include a notice stating that the Source Code version of the Covered Code is available under the terms of this License, including a description of how and where You have fulfilled the obligations of Section 3.2. The notice must be conspicuously included in any notice in an Executable version, related documentation or collateral in which You describe recipients' rights relating to the Covered Code. You may distribute the Executable version of Covered Code or ownership rights under a license of Your choice, which may contain terms different from this License, provided that You are in compliance with the terms of this License and that the license for the Executable version does not attempt to limit or alter the recipient's rights in the Source Code version from the rights set forth in this License. If You distribute the Executable version under a different license You must make it absolutely clear that any terms which differ from this License are offered by You alone, not by the Initial Developer or any Contributor. You hereby agree to indemnify the Initial Developer and every Contributor for any liability incurred by the Initial Developer or such Contributor as a result of any such terms You offer. 3.7. Larger Works. You may create a Larger Work by combining Covered Code with other code not governed by the terms of this License and distribute the Larger Work as a single product. In such a case, You must make sure the requirements of this License are fulfilled for the Covered Code. 4. Inability to Comply Due to Statute or Regulation. If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered Code due to statute, judicial order, or regulation then You must: (a) comply with the terms of this License to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in Section 3.4 and must be included with all distributions of the Source Code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it. 5. Application of this License. This License applies to code to which the Initial Developer has attached the notice in Exhibit A and to related Covered Code. 6. Versions of the License. appendix 148 6.1. New Versions. Netscape Communications Corporation ("Netscape") may publish revised and/or new versions of the License from time to time. Each version will be given a distinguishing version number. 6.2. Effect of New Versions. Once Covered Code has been published under a particular version of the License, You may always continue to use it under the terms of that version. You may also choose to use such Covered Code under the terms of any subsequent version of the License published by Netscape. No one other than Netscape has the right to modify the terms applicable to Covered Code created under this License. 6.3. Derivative Works. If You create or use a modified version of this License (which you may only do in order to apply it to code which is not already Covered Code governed by this License), You must (a) rename Your license so that the phrases "Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in your license (except to note that your license differs from this License) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public License and Netscape Public License. (Filling in the name of the Initial Developer, Original Code or Contributor in the notice described in Exhibit A shall not of themselves be deemed to be modifications of this License.) 7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN "AS IS" BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NONINFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER. 8. TERMINATION. 8.1. This License and the rights granted hereunder will terminate automatically if You fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the Covered Code which are properly granted shall survive any termination of this License. Provisions which, by their nature, must remain in effect beyond the termination of this License shall survive. 8.2. If You initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against Initial Developer or a Contributor (the Initial Developer or Contributor against whom You file such action is referred to as "Participant") alleging that: (a) such Participant's Contributor Version directly or indirectly infringes any patent, then any and all rights granted by such Participant to You under Sections 2.1 and/or 2.2 of this License shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice You either: (i) agree in writing to pay Participant a mutually agreeable reasonable royalty for Your past and future use of Modifications made by such Participant, or (ii) withdraw Your litigation claim with respect to the Contributor Version against such Participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by Participant to You under Sections 2.1 and/or 2.2 automatically terminate at the expiration of the 60 day notice period specified above. (b) any software, hardware, or device, other than such Participant's Contributor Version, directly or indirectly infringes any patent, then any rights granted to You by such Participant under Sections 2.1(b) and 2.2(b) are revoked effective as of the date You first made, used, sold, distributed, or had made, Modifications made by that Participant. 8.3. If You assert a patent infringement claim against Participant alleging that such Participant's Contributor Version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the licenses granted by such Participant under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license. 8.4. In the event of termination under Sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by You or any distributor hereunder prior to termination shall survive termination. 9. LIMITATION OF LIABILITY. appendix UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU. 149 appendix 10. U.S. GOVERNMENT END USERS. The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein. 11. MISCELLANEOUS. This License represents the complete agreement concerning subject matter hereof. If any provision of this License is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered to do business in the United States of America, any litigation relating to this License shall be subject to the jurisdiction of the Federal Courts of the Northern District of California, with venue lying in Santa Clara County, California, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys' fees and expenses. The application of the United Nations Convention on Contracts for the International Sale of Goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed against the drafter shall not apply to this License. 12. RESPONSIBILITY FOR CLAIMS. As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to constitute any admission of liability. 13. MULTIPLE-LICENSED CODE. Initial Developer may designate portions of the Covered Code as "Multiple-Licensed". "Multiple-Licensed" means that the Initial Developer permits you to utilize portions of the Covered Code under Your choice of the NPL or the alternative licenses, if any, specified by the Initial Developer in the file described in Exhibit A. EXHIBIT A -Mozilla Public License. ``The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.mozilla.org/MPL/ Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License for the specific language governing rights and limitations under the License. The Original Code is ______________________________________. The Initial Developer of the Original Code is ________________________. Portions created by ______________________ are Copyright (C) ______ _______________________. All Rights Reserved. Contributor(s): ______________________________________. appendix 150 Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in which case the provisions of [______] License are applicable instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] License and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] License. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] License." [NOTE: The text of this Exhibit A may differ slightly from the text of the notices in the Source Code files of the Original Code. You should use the text of this Exhibit A rather than the text found in the Original Code Source Code for Your Modifications.] Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. Model : Serial No. : Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project