Room Air Conditioner OWNER'S MANUAL ? Please read before ? carefully and thoroughly operating this unit. Contact the authorized SVC man for this manual repair or maintenance of this unit. ? Contact the installer for installation of this unit. ? The ? appliance is not intended for by young children or infirm persons without supervision. Young children should be supervised to ensure they do not play with the appliance. Prior to use that installation, this air-conditioning unit must be submitted for approval by the utility service which provides electricity (EN 61000-3 Norm). Safety precautions Safety Precautions Warning ................................2 To Caution .................................3 prevent injury and property damage, follow these instructions. Incorrect operation damage, symbols. the seriousness of which is indicated before operation ignoring instructions will cause the by harm or following WARNING WARNING Operating Instructions Preparation due to ..4 This shows the symbol possibility of death serious or injury. Remote Control Features .....5 Operation CAUTION CAUTION Mode Selection ......6 This Additional features ..............13 TroubleshtingpCadMcOISfyP 2 indicates the symbol possibility of injury or damage to property. The Care and Maintenance items following are classified by these symblos. Care and Maintenance .......17 Operation Tips ....................19 Never Do This Troubleshooting tips Do This Always Before You Call For Service ...............20 WARNING WARNING Plug in the properly. ? Otherwise, it will or cause fire due to heat Do not operate plug power Do not stop the unit by damage or use an unspecified power cord. inserting or pulling out the power plug. electric shock generation or ? It will cause to heat or electric shock or fire due generation. ? It will ? In the electric shock. Do not modify power cord length or share the outlet with other appliances. ? It will cause to heat electric shock or fire due Do not operate with wet hands or in It may cause electric shock. Do not allow water to grounding may cause electric ? shock. Unplug the unit if sounds, smell, comes ? fire. supply cord is damaged, it mut be replaced by the manufacturer or its service agent or a similarly quallfied person in order to avoid a hazard. (Y Attachment) occupants only. ? run into This could damage Always install and electric parts. No or your health. generation. Always perform grounding work. ? electric shock Do not direct airflow at room damp environment. ? cause or It may cause failure of machine electric shock. strange Do not smoke loose use or or ? the socket if it is a air dedicated leakage breaker switching board. No installation may cause fire and electric shock accident. Do not open the entrance during operation. damaged. from it. It may cause fire and electric shock accident. ? Keep firearms away. It may cause fire and electric shock. Do not heating ? the power cord close to the tools. It may cause electric shock. Do not use the power cord near flammable gas or combustibles, such as gasoline, use benzene, thinner, etc. ? It may cause fire. ? It may cause fire and electric shock. ? It may cause an explosion or fire. WARNING WARNING OPERATING Ventilate before Do not disassemble operating air conditioner when gas goes out. ? It may burn. cause explosion, fire and, COOLING MODE INDOOR OUTDOOR or modify products randomly. ? TEMPERATURE(°C) MAX. MIN. MAX. MIN. 32°C2 1 °C4 3 °C 21°C HEATING MODE INDOOR OUTDOOR MAX. MIN. MAX. MIN. 27°C2 0 °C2 4 °C 1°C It may cause failure and electric shock. CAUTION CAUTION Never touch the metal of the unit when parts removing Do not clean the air Ventilate well when used conditioner with water. together with a stove, etc. the filter. ? They are sharp injury. When and may cause ? Water may enter the unit and degrade the insulation. It may cause an electric shock. Do not cleaning the unit, first make put a pet or plant where it will exposed to direct the power and breaker are turned off. sure ? An oxygen house Do not Since the fan rotates at high speed during operation, cause injury. it may ? This could the window in storm Operation may with windows cause or opened ? of indoor and wetting air flow. vegetables, precision machine, It may cause failure of or accident. Do not ? ? or conservation of art articles. It may or cause vegetables damage or of animals loss of plug by the head of the power plug when taking Turn off the main power switch when not using it for it out. a cause electric shock and ? damage. Ensure that place obstacles around the absorption inlet or instead of blowing-out inlet. use a or animals Hold the It may Do not such pet as long time. It may or fire. cause failure of product of household furniture. soaking ? appliance for special property. hurricane. ? the occur. purpose such plant. and close Stop operation injure use may be or ? shortage use appliance ? If leaving appliance damaged, there is concern of damage due to the falling of product. Do not every two weeks. ? ? There is Do not drink water drained place heavy object on the danger shock. of fire or electric without filters may failure. Operation cause power cord and take care so that the cord should not be pressed. soft cloth. scratching Always insert the filters securely. Clean it once appliance is not damaged due to the use for a long time. thinner but Appearance may be deteriorated due to change of product color or installation console of the outdoor strong detergent as wax or an from air conditioner. ? It contains contaminants and will make you sick. of its surface. Use caution when unpacking and installing. Sharp edges could cause injury. If water enters the product, turn the power switch of the main body of appliance off. After taking the power-plug out from the socket, contact with the service center. SafetyPrcuionsOpgICdMTblh 3 before Preparation operation How to Insert the Batteries Remove the battery arrow direction. Insert new battery batteries are installed Reattach the cover cover by pulling making sure correctly. by sliding it according that the it back into (+) to the and of (-) position. NOTES: TroubleshtingpCadMcOISfyP 4 ? Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. Storage and Tips For Using The remote control may be stored on a wall. ? the Remote Control by mounting it ? To operate the air conditioner, aim the the signal receptor. room remote control at Signal Receptor Receives the signals from the remote control.(Signal receiving sound: two short beeps or one long beep.) Operation Indication Lamps On/Off DOOR system operation. Lights up during : Lights up during Sleep Timer : Lights up during Defrost Mode : Lights up during Defrost Mode or Hot Start operation (Heat pump model only) OUTDOOR UNIT : Lights up during outdoor (Cooling model only) Sleep OUT the : Mode OPERATION Timer Mode Auto operation. operation. unit operation. Signal Display (Inverter only) : Plasma : Power Indicates the and the setting temperature operating frequency of compressor.(5 steps) The function illustrates its dynamic mode receptor Operation by using a indication lamps multiple lighting system. About the remote control The remote control transmits the signals to the on the system system. Features of the Remote Control- Door Signal transmitter 1 START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2 OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3 ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4 INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS. 5 JET COOL Used to start stop the speed cooling. (Speed cooling operates super 5 1 or high fan speed in cooling mode.) 6 CHAOS SWING BUTTON Used to stop or start louver movement and set the desired up/down airflow direction. 7 ON/OFF TIMER BUTTONS Used to set the time of starting and 6 3 Opened stopping operation. (See page 13) 4 10 2 8 TIME SETTING BUTTONS Used to adjust the time. (See page 9 TIMER SET/CANCEL BUTTON Used to set the timer when the desired time is obtained and to cancel the Timer CANCEL 9 7 ON OFF SET 11 12 13) 8 operation. (See page 13) 13 14 SLEEP MODE AUTO BUTTON Used to set Sleep Mode Auto operation. 15 16 10 (See page 13) 11 AIR CIRCULATION BUTTON Used to circulate the room air without or Flip-up door (opened) 12 13 Operation Mode 14 Cooling Operation Auto Healthy Operation Dehumidification 15 Operation 16 Heating Operation ? Cooling Model( ), Heat Pump Model( ) cooling heating. (See page 14) ROOM TEMPERATURE CHECKING BUTTON Used to check the room temperature. PLASMA(OPTIONAL) Used to start or stop the function. (See page 11) plasma-purification HORIZONTAL AIRFLOW DIRECTION CONTROL BUTTON (NOT ON ALL MODELS) Used to set the desired horizontal airflow direction. (See page 14) RESET BUTTON Used prior to resetting time batteries. or after replacing 2nd F Button Used prior to using modes printed in blue at the bottom of buttons. (See page 12) SafetyPrcuionsOpgICdMTblh 5 How to use the Operation Mode Selection button Cooling Operation TroubleshtingpCadMcOISfyP 6 Press the 1 Start/Stop button. The unit will respond with a beep. 2 Open the door on the remote control. To select Cooling Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the Auto Cooling 3 Close the door lower than the set within a arrow. Healthy Dehumidification on Heating (Heat pump model only) the remote control. Set the room temperature temperature. The temperature can be range of 18°C~30°Cin 1°C increments. ON To raise the temperature To lower the temperature 4 Set the fan with the door speed again of the remote control still closed. You can select the fan speed in four steps- low, medium, high and CHAOS. Each time the button is fan Natural wind For more by the fresh CHAOS feeling CHAOS mode. In this speed according speed pressed, the mode is shifted. logic than other fan mode, press the Indoor Fan the wind blows like natural breeze by to the CHAOS logic. speed, Speed Selector and set to automatically changing fan Auto Operation Press the 1 Start/Stop button. The unit will respond with a beep. 2 Open the door on the remote control. To select Auto Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the Cooling ON 3 The arrow. Auto Healthy Dehumidification temperature and fan speed electronic controls based on are Heating (Heat pump model only) automatically the actual room set by the temperature. If change the set temperature, press the Room Temperature Setting buttons. The cooler or warmer you feel, the more times (up to two times) you should press the button. The set temperature will be changed automatically. you want to To raise the temperature To lower the temperature During Auto Operation: You cannot switch the indoor fan already been set by the Fuzzy rule. If the system is not operating as desired, manually switch to another mode. The system will not automatically switch from the cooling mode to the heating mode, or from heating mode to cooling mode, it must be done by manually resetting. During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and down automatically. If you want to stop auto-swing, press the chaos swing button again. speed. It has SafetyPrcuionsOpgICdMTblh 7 Healthy Dehumidification Operation Press the Start/Stop button. The unit will respond with a beep. 1 TroubleshtingpCadMcOISfyP 8 2 Open the door the remote control. To select on Dehumidification Operation, press the Healthy Operation Mode Selection button. Each time the button is shifted in the direction of the 3 Set the fan operation Healthy Dehumidification speed again mode is arrow. Auto Cooling the pressed, Heating (Heat pump model only) with the door of the remote control still closed. You speed in four stepslow, medium, high, or CHAOS. Each time the button is pressed, the fan speed mode is shifted. can ON select the fan Natural wind For fresh CHAOS logic press the Indoor Fan Selector and set to CHAOS mode. In this mode, the wind more Speed by the feeling than other fan speed, blows like natural breeze according to the CHAOS by automatically changing logic. fan speed During Healthy Dehumidification Operation: If you select the dehumidification mode on the operation selection button, the A/C starts to run the dehumidification function. It automatically sets the room temp. and airflow volume to the best condition for dehumidification, based on In this case, however, the setting control the room temp. either. the sensed current temp. is not room displayed temp. in the remote control and you are not able to During the healthy dehumidification function, the airflow volume is automatically set according to the optimization algorithm responding to the current room temp. status which makes the room condition healthy and comfortable even in the high humidity season. Heating Operation(Heat pump model 1 Start/Stop button. The unit will respond with a beep. 2 Open the door on Operation, press Press the the remote control. To select the Each time the button arrow. Auto Cooling Close the door Healthy Dehumidification on Heating Operation Mode Selection button. is pressed, the operation mode is shifted in the direction of the 3 only) Heating (Heat pump model only) the remote control. Set the temperature higher than the room temperature. The temperature can be set within a range of 16°C~30°Cin 1°C increments. ON To raise the temperature To lower the temperature 4 Set the fan speed again with the door of the remote control still closed. You the fan speed in four can select steps--low, medium, high and CHAOS. Each time the button pressed, the fan speed mode is shifted. Natural wind For more by the fresh CHAOS feeling CHAOS mode. In this speed according is logic than other fan mode, press the Indoor Fan the wind blows like natural breeze by to the CHAOS logic. speed, Speed Selector and set to automatically changing fan SafetyPrcuionsOpgICdMTblh 9 Jet Cool Operation 1 TroubleshtingpCadMcOISfyP 10 2 Press the Start/Stop button. The unit will respond with a beep. Press the Jet Cool button to the speed cooling will operate in super high fan speed on 3 operate cooling mode and the unit mode for 30 minutes. To cancel the Jet Cool mode, press the Jet Cool button or the fan speed button or the room temperature setting button again and the unit will operate in high fan speed on cooling mode. or or NOTE: During the JET COOL function at any moment, the A/C starts to blow the cool air at extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is especially used to cool the room temp. in the shortest time in a hot summer. In heat pump mode or neuro fuzzy mode, however, the JET COOL function is not available. In order to return to the normal mode from the JET COOL mode, you just press either the operation mode selection button, airflow volume selection or temp. setting button or the JET COOL button again. cooling PLASMA Purification Operation(Optional) Press the 1 Start/Stop button. The unit will respond with a beep. 2 Open the door on the remote control. Press the PLASMA air purifying operation ON/OFF button. Operation will start when the button is pressed and stop when the button is pressed again. 3 Set the fan closed. You speed again can with door of the remote control select the fan speed in four steps-low, medium, high or CHAOS. Each time the button is pressed, the fan speed mode is shifted. Air purifying operation (PLASMA) can be cooling, Heating or any other operations. PLASMA Air with Purifying Operation only If you press the only PLASMA button, PLASMA air purifying operates. only Then, fan speed is low. You can select the fan speed in four steps-low, medium, high or CHAOS. Each time the button speed ( mode is shifted. ) is pressed, the fan SafetyPrcuionsOpgICdMTblh 11 2nd F TroubleshtingpCadMcOISfyP 12 Operation Press the 1 Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote control and press the 2nd Function button to operate functions printed in blue at bottom of buttons. (Check the display.) indication of 2nd function These buttons on operate the timer setting remote control as follows: CANCEL ON OFF SET CANCEL ON OFF SET 3 2nd function goes off in a short time the button is pressed again. automatically or when For more details, refer to functions next page. Additional features Mode Sleep 1 Press the Sleep To cancel the press the sleep Mode Auto button several times until the star Mode Auto button to set the time you want the unit to turn off automatically. ( 2 programmed in one-hour by pressing the Sleep Mode ) disappears increments The Auto operation display. Note: The Sleep Mode will be operated at slow fan speed (cooling) or medium fan speed (heat pump only) for quiet sleeping. mode is available for 1 to 7 times. To sleep alter the time the in period steps of Mode Button while Sleep 1 hour, press aiming IN COOLING MODE OR HEALTHY at air DEHUMIDIFICATION MODE: conditioner. The Make sure the Sleep Mode Auto LED Setting the 1 from the The Timer is button 1 to 7 times. 3 Sleep Mode, Time over up. the next 30 minutes and for comfortable sleeping. Press the Time Setting by 2°C in 1 hour Time when you have pressed the Reset button. If you have just replaced the can be set lights temperature will automatically rise by 1°C only 3 buttons until the desired time is set. batteries, the Reset button should be pressed to reset the time. Press the Start/Stop button. Press the Timer SET button. 4 CANCEL Press 2nd F button 2 SET and check if 2nd F icon is Note: Check the indicator on. for A.M. and P.M. Delay Start/Pre-Set Stop 1 2 3 Make sure the time is set remote control correctly on the To set the selected 5 display. time, press the Timer SET button while aiming the remote control at the signal Press 2nd F button. SET receptor. Press the ON/OFF Timer buttons to turn Timer CANCEL To cancel the timer ON off. on or OFF CANCEL setting Check if 2nd F icon is off. Press the Timer Cancel button while 4 Press the Time ET Setting aiming remote control at the buttons until the desired receptor. time is set. (The timer lamp on the the display will go out.) NOTE: Select one of the following four OFF Timer Delay air conditioner and types of operation. with the unit Delay signal ON Timer Delay running OFF and ON Timer Delay ON and OFF Timer SafetyPrcuionsOpgICdMTblh 13 Vertical Airflow Direction Control The up/down airflow (Vertical Airflow) adjusted by using the remote control. be can Note: If you press the CHAOS swing button, the horizontal airflow direction is changed automatically based on the CHAOS algorithm evenly and at the feel most TroubleshtingpCadMcOISfyP 14 to distribute the air in the same room time to make the human body enjoying a natural breeze. Always use the remote control to adjust the up/down airflow direction. Manually moving the vertical airflow direction louver by hand, could damage the air 1 Press the Press Chaos 2 Swing as if conditioner. button to start the unit. Start/Stop comfortable, When the unit is shut off, the up/down airflow direction louver will close the air outlet vent of the system. button and the louvers will To up and down. Press the Chaos Swing button again to set the vertical louver at the swing adjust left/right(Horizontal Airflow) direction Caution : Ensure that the unit is turned off before adjusting the desired airflow direction. horizontal airflow direction control. Carefully open vertical louver to allow access to the horizontal airflow direction. Adjust the left/right airflow direction by hand. Horizontal Airflow Direction Control (Optional) The left/right(Horizontal Airflow) can be adjusted by using the remote control. Press the Start/Stop button to start the unit. Open the door on the remote control. Press the Airflow Direction Start/Stop button and the louvers will swing left and right. Press the Horizontal Airflow Direction Control Button again to set the horizontal louver at the desired airflow direction. Air Circulation Mode Circulates the 1 2 Press the Open room Start/Stop the door on air without cooling or button. the unit will heating. respond with a beep. the remote control. Press the Air Circulation button. Close the door remote control. Now each time that you press the Indoor Fan shifted from low to CHAOS and back to low again. CHAOS Air Fan speed is on low. Fan speed Speed Selector, is on medium. Fan the fan speed is on the speed on is high. Note: CHAOS Air economizes power consumption and automatically changed from high to low or vice versa, prevents overcooling. The fan speed is depending on the ambient temperature. Forced Operation Operation procedures when the remote control can't be used. The operation will button is pressed. If you want to the button. be started if the power stop operation, re-press Power button Open the front panel upward Cooling Model Heat pump Model Room Temp. ≥ 24°C2 1 °C ≤ Room Operating mode Cooling Cooling Indoor FAN Speed High High Setting Temperature Test Healthy Temp. < 24°C Dehumidification High Room Temp. < 21°C Heating High 22°C2 2 °C2 3 °C2 4 °C operation OPERATION, the unit operates in cooling mode at high speed fan, regardless of room temperature and resets in 18 minutes. During test operation, if remote controller signal is received, the unit operates as remote controller sets. During the TEST If you want to use this operation, open the front pressed for about 3 seconds. If you want to panel upward and Press the power button let it be stop the operation, re-press the button. Auto restart In again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions. So there is no need of activating this function by pressing any key or button. In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3minutes later. As the compressor starts, the fan speed also resumes its previous setting mode. case the power comes on Helpful information Fan speed and cooling capacity. The cooling capacity indicated in the specification is the value when the fan speed is set to high, and the capacity will be lower at low or medium fan speed. High fan speed is recommended when you wish to cool the room quickly. High Speed SafetyPrcuionsOpgICdMTblh 15 Telephone Control Operation(Optional) Calling from outside, you can start the air conditioner to keep the room comfortable. Even though you went out with the air conditioner on, you can turn it off using the phone Dial the number which is connected with the air TURN ON 1 conditioner. After You TroubleshtingpCadMcOISfyP 16 outside. is can hear the "Beep" using along OGM sound then press "0" "0" "7" "8" off), When 5 times. ringing with ARS (if the air conditioner accordingly. telephone provided after signal sound rings four times and then "Beep"(sounds from telephone itself) sounds so that outside recording can be done. ON ON is guide Slowly password press With the sound "0" "0" "Beep, Beep" "7" and "8" in order. the air conditioner starts on. up the Hang Dial the number which is connected with the air TURN OFF 2 phone. conditioner. After You ringing can 5 times. hear the conditioner is When "Beep Beep" on), then using along OGM sound press "0" "0" with ARS (if the air "7" "9" accordingly. telephone provided after signal sound rings four times and then "Beep"(sounds from telephone itself) sounds so that outside recording can be done. OFF OFF guide Slowly is press password "0" "0" "7" and "9" in order. With the sound Hang up the "Beep---" the air conditioner is turned off. phone. Note: This If If product works after telephone rings 5 times. internal user picks up the phone before 5 rings, Telephone control function does not work. user doesn't push the telephone button 25 seconds after beep, Telephone control function When using along with ARS doesn't work. telephone The numbers of response bell should be adjusted to four times if pressing "Out-of-office" button or other action for automatic response. The recording time of OGM (Outgoing Message) should be less than approximately 15 seconds. If it is connected to key phone, it cannot be worked. taking Care and maintenance of the air conditioner CAUTION: Before performing any maintenance, turn off the main power to the system. Indoor Unit Never Grille, Case, and Remote Control Turn the system clean, wipe use bleach with or off before a soft, dry ? To cleaning. use followings: Water hotter than 40°C Could cloth. Do not any of the cause deformation and/or discoloration. abrasives. ? Volatile substances NOTE: Could Supply power must be disconnected before cleaning the indoor unit. conditioner. the surfaces of the air damage Powder Gasoline Air inlet vent Air outlet vent Vertical louver Air filters (behind front panel) 1 Horizontal louver Lift the front slightly AIR FILTERS The air filters behind the front checked and cleaned more once grille 2 should be in every 2 weeks or access forward to panel remove Clean the filter with and the filter tab pull the filter. a vacuum cleaner or warm, soapy water. ? often if neccessary. ? If dirt is conspicuous, wash with a solution of detergent in lukewarm water. If hot water (40°C or more) is used, it may be deformed. 3 After washing with water, dry well in the shade. 4 1 PLASMA FILTER, DEODORIZER 2 FILTER(OPTIONAL) Re-install the air filter. After removing forward to Dip more once in every 3 months or 3 often if necessary. 4 5 with neutral After seconds after cause an opening the inlet electric shock. grille, it may 3 for 20~30minutes. discharge Re-install the PLASMA filter to the PLASMA Filter Don't touch this PLASMA Filter within 10 detergent, Note the cuts of electric position. 2 the PLASMA filter. Dry the PLASMA filter in the shade for a day (Especially, the humidity must be removed perfectly on this parts). DEODORIZER Filter 1 remove filters, pull slightly the PLASMA filter into the water mixed The PLASMA filter behind the air filters should be checked and cleaned the air removing the air forward to remove in the sunlight Dry lines. original filters, pull slightly the DEODORIZER filter. for two hours. Re-install the DEODORIZER filter to the original position. SafetyPrcuionsOpgICdMTblh 17 Replacement of Purifying Filter(Option) ? Recomended 1 Open use period front panel : About 2 years and remove air 2 Remove air 3 Insert purifying filters. filters. new air purifying filters. Air filter TroubleshtingpCadMcOISfyP 18 2 3 4 Reinsert air filters and close front panel. Air purifying filter Outdoor Unit The heat exchanger coils and panel vents of the outdoor unit should be checked regularly. If clogged (Side) Air intake with dirt or soot, the heat exchanger and panel vents vents may be professionally steam cleaned. NOTE: (Rear) Piping Drain Hose Air outlet vents coils will reduce the Dirty clogged operating efficiency of higher operating costs. or the system and cause (Rear) (Rear) Air intake vents (Side) Piping Drain Hose Air intake vents (Side) Piping Drain Hose Air outlet vents Air outlet vents When the air conditioner is not going to be used for a long time. When air conditioner is not used for a long going to be When the air conditioner is to be used time. Clean the air filter and install it in the indoor Operate the air conditioner on Air circulation mode (Refer to page 14) for 2 to 3 hours. unit. (Refer to page ? This will dry 17 for cleaning filters.) out the internal mechanisms. Turn off the circuit the again. breaker, and disconnect plug. Check that the air inlet and outlet of the CAUTION CAUTION indoor/outdoor unit are not blocked. Turn off the circuit breaker when the air conditioner is not going to be used for a long time. Dirt may collect and may cause a fire. Remove the batteries from the remote control. Operation Tips Do not overcool the room. This is not and good for the wastes electricity. health Keep blinds or curtains Keep the closed. uniform. Do not let direct sunshine enter Adjust the the horizontal airflow direction to room when the air conditioner is in operation. ensure a in the Make sure that the doors and windows are Avoid doors and opening windows to keep as much shut as Clean the air filter regularly. tight. the cool air in the room. vertical and uniform temperature room. Ventilate the room occasionally. Blockages possible temperature room in the air filter Since windows reduces the airflow and lowers the cooling and dehumidifying effects. Clean at least every two weeks. once in it is are kept closed, idea to open them and ventilate the room now and a then. good SafetyPrcuionsOpgICdMTblh 19 Before you call for service... Troubleshooting Tips! Save ? Check the following points contact your dealer or before ? operate. ? TroubleshtingpCadMcOISfyP 20 a service.... If the fault peculiar ? odor. persists, please See page Have you made a mistake in timer operation? Has the fuse blown or has the circuit breaker been has or Explanation The air conditioner does not room requesting repairs money! service center. Case The time and tripped? - Check that this is not the 13 a damp walls, carpet, furniture, or smell exuded by cloth items in the - room. It is seems that condensation leaking ? from the air Condensation occurs when the airflow from the air conditioner cools the warm room air. - conditioner. Air conditioner does not ? This is the operate for about ? Wait about three minutes and 3 minutes when restarted. Does not cool or protector of the mechanism. operation will begin. heat ? Is the air filter dirty? See air filter cleaning 17 instructions. effectively. ? Has the temperature been ? Are the indoor unit's air inlet set or incorrectly? The air conditioner is ? For a - noise that sounds like water -This is the sound of freon noisy. 6,9 outlet vents obstructed? operation - flowing flowing. inside the air conditioner unit. ? For air a noise that sounds like the compressed into atmosphere. -This is the sound of the dehumidifying water being processed inside the air conditioning releasing - unit. Remote control faint, or no is display display at all. ? Are the batteries ? Are the batteries inserted in the and Crack sound is heard. ? (-) depleted? opposite (+) 4 directions? This sound is generated by the expansion/constriction of the front panel, due to changes of temperature. etc. - Memo 21 Memo 22 P/No.: 3828A20242R After reading this manual, Printed in Korea keep it in a place easily accessible to the user for future reference.