LG | PQCSW421E0A.ENCXIDA | LG PQCSW421E0A.ENCXLEU Owner’s Manual

ENGLISH
User Manual(GUI)
After reading, store this User’s Guide in an easily accessible place for all users.
Model Name: ACP, ACP BACnet, ACP Lonworks, AC Smart Premium
*MFL68301305*
P/NO : MFL68301305
www.lg.com
EXPLANATORY NOTES
i
EXPLANATORY NOTES
Copyrights
The contents of this Central Controller User Guide are protected by international copyright laws,
and the Computer Program Protection Act. The contents of the User Guide and the programs
mentioned herein may only be used under license from LG Electronics in strict adherence to the user
agreement.
You may not reproduce or distribute, by any means, copies of this User Guide, or any part of it,
without prior approval from LG Electronics.
Registered Trademarks
Central Controller is a registered trademark of LG Electronics. All other products and company
names are trademarks of their respective owners and are used for illustrative purposes only.
ENGLISH
Copyright © 2014 LG Electronics. All rights reserved.
ii
EXPLANATORY NOTES
How to Use This Guide
Please read from beginning to end this User Guide before using Central Controller. Store this guide
so that is also easily accessible.
Notations Used In This Guide
• Control buttons displayed within the system are marked by boldface text in square brackets ([ ]).
Example: [OK], [Save]
• Option titles displayed in the program are marked by boldface text.
Example: Start, Programs
ENGLISH
• Keyboard strokes used by the system are marked by boldface text in angle brackets (< >).
Example: <Esc>
TABLE OF CONTENTS
iii
TABLE OF CONTENTS
1SAFETY
PRECAUTIONS
7STARTING
8
8
–Login
–Logout
9Home screen composition and
features
11USING THE PROGRAM
11Control/Monitor
11
16
37
–Control/Monitoring screen
composition and features
–Device Control
–Monitoring a Device
38Schedule
38
–Schedule Screen composition and
features
39
–Creating Schedules
42
43
44
–Checking Schedules
–Editing Schedules
–Deleting Schedules
45Auto Logic
45
55
58
64
–Peak Control
–Demand Control
–Time-limit Operation
–InterLocking
68
–Statistics Screen Composition and
Features
69
–Querying Statistics
71Report
71
–Report screen composition and
features
73
–Querying Report
74Installing
74
78
–Registering Device
–Managing Device
82Environment
83
–General Setting
96
–Advance Setting
107
–Network Setting (AC Smart Premium
Only)
90
101
111
116
122
–Screen Setting (AC Smart Premium
Only)
–Customer Setting
–E-Mail Setting (ACP, ACP Lonworks,
AC Smart Premium Only)
–TMS Setting
–Channel Settings (ACP, ACP
Lonworks, AC Smart Premium Only)
ENGLISH
7Login and logout
68Statistics
MEMO
ENGLISH
SAFETY PRECAUTIONS
1
SAFETY PRECAUTIONS
• This product must be installed by an installation professional from an LG authorized service
center.
• Any issues stemming from an installation by an unauthorized person is the responsibility of
the user and will not be covered by warranty.
• The following safety precautions are to prevent any unforeseen dangers or damage.
• This product has been designed for business use, or for areas outside the home, and has
passed the Electromagnetic Interference Test.
It can result in serious injury or death when the directions are ignored.
CAUTION
It can result in minor injury or product damage when the directions are ignored.
WARNING
Installation
yy To reinstall the product, please contact the dealer from where you purchased the
product, or a service center for reinstallation service.
-- Installation of the product by an unauthorized person may result in fire, electric shock, explosion, injury, or a malfunctioning of the product.
yy Do not twist or damage the power cord.
-- It may cause fire or electric shock.
yy For electrical work, please contact the dealer from where you purchased the product, or
a service center.
-- Disassembly or repair by an unauthorized person may result in fire or electric shock.
yy Install the product in an area shielded from rain.
-- If water gets into the product, it may malfunction.
yy Do not install the product in a humid area.
-- If the product is damp, it may malfunction.
yy For installation of the product, please contact the dealer from where you purchased the
product, or a service center.
-- Installation of the product by an unauthorized person may result in fire, electric shock, explosion, injury, or a malfunctioning of the product.
ENGLISH
WARNING
2
SAFETY PRECAUTIONS
yy For electrical work, please have an electrician do the work based on the installation
manual and specified circuit diagram.
-- Using an unsuitable cord, or having a non-professional work on the electricals may result in fire
or electrical shock.
yy Do not place the product near a fire source.
-- It may result in the product catching fire.
yy If the product is installed in a hospital or a communication base station, provide
sufficient protective equipment against electrical noise.
-- The product may malfunction or other products may work abnormally.
yy Securely install the product.
-- If the product is not secured during installation, it may fall or malfunction.
ENGLISH
yy Read the manual thoroughly to correctly install the product.
-- If not, an incorrect installation may cause fire or electric shock.
yy When wiring the product, do not use a non-standard cable, nor extend the cable
excessively.
-- It may cause a fire or electric shock.
yy Securely install the power cord and communication cable.
-- An unsecure installation may result in a fire or electric shock.
yy Do not connect the power cord to the communication terminal.
-- It may cause a fire, electric shock, or a product malfunction.
yy Do not install the product in an area near combustible gas.
-- It may result in fire, electric shock, explosion, injury, or a malfunctioning of the product.
Use
yy Do not place a heavy object on the power cord.
-- It may cause a fire or electric shock.
yy Do not change or extend the power cord arbitrarily.
-- It may cause a fire or electric shock.
yy Use the cord specific to the product.
-- Using an unauthorized non-standard cord may result in a fire or electric shock.
yy Do not use a heat device near the power cord.
-- It may cause a fire or electric shock.
yy Ensure that water never gets into the product.
-- It can result in an electric shock, or the product may malfunction.
yy Do not place any container with liquid on the product.
-- The product may malfunction.
SAFETY PRECAUTIONS
3
yy Do not click(touch) the product with wet hands.
-- It may cause a fire or electric shock.
yy Use standard components.
-- Use of an unauthorized product may result in fire, electric shock, explosion, injury, or a malfunctioning of the product.
yy If the product has been submerged in water, you should contact a service center.
-- It may cause a fire or electric shock.
yy Do not shock the product.
-- The product may malfunction.
yy Do not store or use any combustible gas or flammable substances near the product.
-- It may cause a fire, or a product malfunction.
yy Children and the elderly should use the product under the supervision of a guardian.
-- Carelessness may cause an accident, or the product to malfunction.
yy The guardian should prevent children from accessing the product.
-- The product may be damaged or it may fall, causing injury to children.
yy Keep in mind the operating temperature range specified in the manual.
if there is no operating temperature range in the manual, use the product between 0 and
40 ℃ (32 and 104 °F).
-- If the product is used outside this range, the product may be severely damaged.
yy Do not press the switch or button with a sharp object.
-- It can result in an electric shock, or the product may malfunction.
yy Do not wire the product while it is turned on.
-- It may cause a fire or electric shock.
yy If the product sounds or smells different, stop using the product.
-- It may cause a fire or electric shock.
yy Do not place a heavy object on the product.
-- The product may malfunction.
yy Do not spray water on the product, or clean it with a water-soaked cloth.
-- It may cause a fire or electric shock.
yy Do not use the product for the preservation of animals and plants, precision
instruments, art pieces, or for other special purposes.
-- It may cause property damage.
yy Dispose the packing material safely.
-- The packing material may result in personal injuries.
ENGLISH
yy Do not disassemble, repair, or revamp the product arbitrarily.
-- It may cause a fire or electric shock.
4
SAFETY PRECAUTIONS
CAUTION
Installation
yy Securely install the product in an area where the weight of the product can be supported.
-- The product may fall and be destroyed.
yy Do not use the product where there is oil, steam, or sulfuric gas.
-- It may effect the product's performance, or damage it.
yy Check the rated power capacity.
-- It may cause a fire, or a product malfunction.
ENGLISH
yy Use the adapter provided with the product or power from a class 2 24 V~ transformer,
depending on model.
-- If a non-standard adapter is used, the product may malfunction. The adaptor is not provided
with the AC Smart package sold in the U.S.
yy Be careful not to drop or damage the product when moving it.
-- The product may malfunction or the person may sustain an injury.
yy Ensure that the cord is connected securely to prevent dew, water, or insects from getting
into the product.
-- If a foreign substance gets inside, it may cause an electric shock or the product may malfunction.
Use
yy Clean the product with a soft cloth, but not with a solvent-based detergent.
-- The use of a solvent-based detergent may cause a fire or deform the product.
yy Do not click(touch) the panel using a pointy or sharp object.
-- It can result in an electric shock, or the product may malfunction.
yy Do not let the product come into contact with a metal substance.
-- The product may malfunction.
yy When sterilizing or disinfecting, stop using the product.
-- The product may work abnormally.
yy Do not click(touch) inside the product.
-- The product may malfunction.
yy Check the condition of the product after using the product for an extended period of
time.
-- If the product is used for an extended period of time, the product's condition may be worsen,
causing injury to the user.
yy Do not leave the product near a flower base, water bottle, or any other liquids.
-- It may cause a fire or electric shock.
SAFETY PRECAUTIONS
5
ENGLISH
yy Transformer selection:
-- Select an insulating product that complies with IEC61558-2-6 and NEC Class 2.
-- In addition, consider the combined power consumption of the modules, accessories, and field
devices installed for the selection of an appropriate transformer.
Main module current: 24 V~, 850 mA
-- Use the provided adaptor when using DC 12 V. The adaptor is not provided with the AC Smart
package sold in the U.S.
6
SAFETY PRECAUTIONS
Class A device
Notes
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
ENGLISH
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
Caution
Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
Disposal of your old appliance
1.When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
2.All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
3.The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4.For more detailed information about disposal of your old appliance,
please contact your city o!ce, waste disposal service or the shop
where you purchased the product.
STARTING
7
STARTING
This section explains how to connect to the system and register devices to setup the environment
(prior to using Central Controller).
Login and logout
The following explains how to log in and out of Central Controller.
Central Controller is, can be controlled not only equipment, but also Web. If you enter the IP address
of the Central Controller in the address bar of the Internet without the installation of another program,
the central control program Central Controller, Web server has is executed automatically, to use the
The Manual, I will explain to Central Controller standard equipment.
Notes
yy You will need the Adobe Flash Player be installed for the Web control.
(Recommended specification : Adobe Flash Player 11)
yy The special character (^), (‘) and (,) are not available.
ENGLISH
functionality of the various content I can.
8
STARTING
Login
You can login as follows.
1. Run Central Controller.
2. After entering your ID and password in the login window, click(touch) [Confirm].
• You are now logged in.
ENGLISH
Logout
You can logout as follows.
1.
On the top right of the Central Controller home screen, click(touch) the [Logout] button.
• You are now logged out.
STARTING
9
Home screen composition and features
The following explains the home screen composition and features.
①
②
④
⑤
⑥
⑦
Number
Item
①
Running Status
(Unit)
②
Time
③
Today's Schedule
④
Main Menu
⑤
Home
⑥
View Menu
⑦
Current Menu
Description
Checks if the devices are operating, stopped, or in error.
Check the current date and time.
(You need Internet connection to check the weather.)
yy Check the registered schedules in chronological order.
yy Click(Touch) the [+] button to move to the schedule
menu.
Use Central Controller main menu.
Return to the home screen.
Display the active menu.
Display the name of the active menu.
ENGLISH
③
MEMO
ENGLISH
USING THE PROGRAM
11
USING THE PROGRAM
The following explains how to use the Central Controller functions.
Control/Monitor
The following explains the Control/Monitor menu options.
Control/Monitoring screen composition and features
The following explains Control/Monitoring screen composition and features.
⑤
Number
Item
①
Select/Deselect All
②
[Drawing] Button
③
[Filter] Button
④
View Type
Select
⑤
Group List
⑥
Monitoring Screen
②
③
⑥
⑦
Description
Select/deselect all devices in a group.
View floor plans of a group.
Select which device types are displayed for
monitoring and control.
Select a view type for the monitoring screen
(Icon/Simple/Detail)
(For more on View Type, refer to page 12)
Check device group listings.
Check the control status of a device.
④
ENGLISH
①
12
USING THE PROGRAM
Number
⑦
Item
Description
Device Control Box
yy Display the device control menu.
yy The device control box shows different menus
depending on the device.
(For more on Control Menu per Device, refer to
page 17)
View Type
Control/Monitor menu has three types of views (icon, simple, and detailed). The following shows the
screen composition and features per view type.
ENGLISH
Icon
The control status is shown in icons. The device icon has a composition and feature as follows.
①
②
④
③
⑤
⑥
Number
Item
Description
①
Operation Mode and
Device Status Icon
②
Device Icon
③
Current Temperature
④
Operation Mode
⑤
Desired Temperature
Display the desired temperature.
⑥
Device Name
Display the name of the device.
The color at the top of the icon box shows the current
operation mode, and the status of the device is
indicated as an icon.
The device to be controlled is indicated as an icon.
The device shown may not represent the appearance
of the actual unit.
Display the current temperature.
Display the operation mode of the device.
USING THE PROGRAM
13
Simple
The control device and operation mode are displayed only.
①
②
Number
Item
Description
①
Operation Mode
The color of the box indicates the current operation
mode.
②
Device Icon
The device to be controlled is indicated as an icon.
All properties of the control device are tabulated in detail.
ENGLISH
Detail
14
USING THE PROGRAM
Monitoring screen colors and icons
Box colors and operation mode per icon
Color
Icon
Operation Mode
Cooling
Ventilation, General
(Blue)
Heating
ENGLISH
Ventilation, Electric Heat
(Orange)
Dehumidification
(Navy)
Fan
(Sky Blue)
Power Saving
(Green)
Auto
Ventilation, Auto
(Purple)
-
ON & Short
-
OFF & Open
-
Error
(Yellow)
(Gray)
USING THE PROGRAM
15
Device status icon
Icon
Device Status
Filter Exchange
Full Lock On
Peak/Demand Control
Control device icon
Icon
Device Type
Indoor Device
ERV
AHU
AWHP
Chiller
DI
DO
DOKIT
ENGLISH
Schedule
16
USING THE PROGRAM
Device Control
You can control the devices as follows.
1. From the main menu, click(touch) the [Control/Monitor] menu icon.
2. Click(Touch) the device group you want to control from the group list.
• The monitoring screen for the device is displayed.
3. Click(Touch) the device you want to control.
• To select all devices, click(touch) the
button at the top.
• The device control area appears at the bottom of the screen.
4. In the device control box, set the control status of the device.
• The device control box shows a different menu depending on the device. For information
about the control area for each device, refer to Control Menu per Device on page 17.
ENGLISH
5. Once you have finalized the settings, click(touch) the [Apply] button.
USING THE PROGRAM
17
Control Menu per Device
The control box menu differs depending on the device. The following shows the control box menu
per device.
Indoor Device
The following is the indoor unit control menu and features.
Operation
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
GoTo
[Schedule▶] Button: Move to Schedule menu.
Room
Display the current temperature.
Set Temperature
Click(Touch) [▲]/[▼] to set the temperature.
(The maximum/minimum temperatures that can be set may differ depending
on the model.)
Mode
yy [COOL] Button: Operates with Cooling Mode.
yy [HEAT] Button: Operates with Heating Mode.
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum mode.
yy [DRY] Button: Dehumidifies during rainy seasons or whenever humidity
is high. You cannot set the temperature in this mode.
yy [FAN] Button: Fan runs without temperature control to clean the air. You
cannot set the temperature in this mode.
Fan Speed
Swing
[Detail. ▶] Button
yy
yy
yy
yy
[LOW] Button: Slow fan speed.
[MED] Button: Medium fan speed.
[HIGH] Button: Fast fan speed.
[AUTO] Button: Fan speed automatically adjusts between low, medium
and high fan speeds.
yy [Set] Button: Turns on automatic oscillation of the louvers.
yy [Clear] Button: Turns off automatic oscillation of the louvers.
Controls details.
ENGLISH
Item
18
USING THE PROGRAM
• Indoor unit fine control
ENGLISH
Item
Operation
Set
Mode
Fan Speed
Swing
Filter Alarm
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
Click(Touch) [▲]/[▼] to set the temperature.
yy [COOL] Button: Operates with Cooling Mode.
yy [HEAT] Button: Operates with Heating Mode.
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum mode.
yy [DRY] Button: Dehumidifies during rainy seasons or whenever humidity is
high. You cannot set the temperature in this mode.
yy [FAN] Button: Fan runs without temperature control to clean the air. You
cannot set the temperature in this mode.
yy
yy
yy
yy
[LOW] Button: Slow fan speed.
[MED] Button: Medium fan speed.
[HIGH] Button: Fast fan speed.
[AUTO] Button: Loops from low to medium to high fan speeds.
yy [Set] Button: Turns on automatic oscillation of the louvers.
yy [Clear] Button: Turns off automatic oscillation of the louvers.
Click(Touch) the Disable button to deactivate the filter exchange alarm.
(For other models, it may not work properly.)
USING THE PROGRAM
Item
Partial Lock
Set Temp Range
[2Setpoint]
Button
Description
yy
yy
yy
yy
yy
yy
yy
yy
[HardLock] Button: Disables remote control for all features.
[Clear] Button: All functions are unlocked.
[ModeLock] Button: Disables remote control for local mode setting.
[Clear] Button: Mode is unlocked.
[FanLock] Button: Disables remote control for local fan speed setting.
[Clear] Button: Fan speed is unlocked.
[TempLock] Button: Disables remote control for local temperature setting.
[Clear] Button: Temperature setting is unlocked.
Click(Touch) [▲]/[▼] to set the temperature limit.
Switches between cooling and heating within the selected temperature range.
ENGLISH
• Indoor 2Setpoint (Auto Operation Mode)
Item
Auto Change
Over
19
Description
Set the auto change over function to switch the operation mode automatically
to keep the proper room temperature.
yy [ON] Button: Enable Auto Change Over
yy [OFF] Button: Disable Auto Change Over
Lower
Click(Touch) [▲]/[▼] to set the lower limit temperature range
(18°C~30°C / 64°F~86°F).
Upper
Click(Touch) [▲]/[▼] to set the upper limit temperature range
(18°C~30°C / 64°F~86°F).
20
USING THE PROGRAM
Item
Setback
Description
Set the setback function to control the proper room temperature when
the indoor unit is turned off. (The setback function works well with "Heat
Recovery" model. For other models, it may not work properly.)
yy [ON] Button: Enable temperature limits
yy [OFF] Button: Disable temperature limits
Cooling Start
Temp.
Click(Touch) [▲]/[▼] to set the cooling start temperature
(21°C~40°C / 70°F~104°F).
Heating Start
Temp.
Click(Touch) [▲]/[▼] to set the heating start temperature (1°C~20°C /
34°F~68°F).
ENGLISH
ERV
The following is the ERV control menu and features.
Item
Operation
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
GoTo
[Schedule▶] Button: Move to Schedule menu.
Room
Display the current temperature.
Set Temperature
Mode
Fan Speed
[Detail. ▶] Button
Click(Touch) [▲]/[▼] to set a desired temperature (the ERV is not activated).
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum temperature.
yy [HEX] Button: Air supply and emissions are all ventilated through the heat
exchanger.
yy [NORM] Button: Ventilate emissions without passing through the heat
exchanger.
yy
yy
yy
yy
[LOW] Button: Slow fan speed.
[HIGH] Button: Fast fan speed.
[SUPER] Button: Maximum fan speed.
[AUTO] Button: Loops from low to high to super fan speeds.
Control details.
USING THE PROGRAM
21
• ERV Fine Control
ENGLISH
Item
Operation
Set
Mode
Fan Speed
Partial Lock
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
Click(Touch) [▲]/[▼] to set a desired temperature (the ERV is not activated).
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum temperature.
yy [HEX] Button: Air supply and emissions are all ventilated through the heat
exchanger.
yy [NORMAL] Button: Ventilate emissions without passing through the heat
exchanger.
yy
yy
yy
yy
[LOW] Button: Slow fan speed.
[HIGH] Button: Fast fan speed.
[SUPER] Button: Maximum fan speed.
[AUTO] Button: Loops from low to high to super fan speeds.
yy [Set] Button: Disables remote control for all features.
yy [Clear] Button: Disable the lock.
22
USING THE PROGRAM
Item
Description
Additional
Function
yy [Drift] Button: Reduces energy consumption by operating in the most
efficient method possible.
yy [Quick] Button: Operates at maximum performance to prevent the room's
contaminated or humid air from entering other spaces.
yy [Clear] Button: Disables power saving / rapid operation.
yy [Heater On] Button: Enables the heater function to heat the room.
yy [Heater Off] Button: Disables the heater function.
Some additional function might not be provided according to your country
such as U.S.
ERV DX
ENGLISH
The following is the ERV DX control menu and features.
Item
Operation
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
GoTo
[Schedule▶] Button: Move to Schedule menu.
Room
Display the current temperature.
Set Temperature
Mode
Fan Speed
[Detail. ▶] Button
Click(Touch) [▲]/[▼] to set the temperature.
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum temperature.
yy [HEX] Button: Air supply and emissions are all ventilated through the heat
exchanger.
yy [NORM] Button: Ventilate emissions without passing through the heat
exchanger.
yy
yy
yy
yy
[LOW] Button: Slow fan speed.
[HIGH] Button: Fast fan speed.
[SUPER] Button: Maximum fan speed.
[AUTO] Button: Loops from low to high to super fan speeds.
Control details.
USING THE PROGRAM
23
• ERV DX Fine Control
ENGLISH
Item
Operation
Set
Mode
Fan Speed
Partial Lock
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
Click(Touch) [▲]/[▼] to set the temperature.
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum temperature.
yy [HEX] Button: Air supply and emissions are all ventilated through the heat
exchanger.
yy [NORMAL] Button: Ventilate emissions without passing through the heat
exchanger.
yy
yy
yy
yy
[LOW] Button: Slow fan speed.
[HIGH] Button: Fast fan speed.
[SUPER] Button: Maximum fan speed.
[AUTO] Button: Loops from low to high to super fan speeds.
yy [Set] Button: Disables remote control for all features.
yy [Clear] Button: Disables the lock.
24
USING THE PROGRAM
Item
Description
Additional
Function
yy [Drift] Button: Reduces energy consumption by operating in the most
efficient method possible.
yy [Quick] Button: Operates at maximum performance to prevent the room's
contaminated or humid air from entering other spaces.
yy [Clear] Button: Disables power saving / rapid operation.
yy [Heater On] Button: Enables the heater function to heat the room.
yy [Heater Off] Button: Disables the heater function.
yy [Humid On] Button: Enables the humidifier function for room humidity control.
yy [Humid Off] Button: Disable the humidifier function (not activated).
Some additional function might not be provided according to your country
such as U.S.
ENGLISH
CoAirconditioner
yy
yy
yy
yy
[COOL] Button: Operates with Cooling Mode.
[HEAT] Button: Operates with Heating Mode.
[AUTO] Button: Operates in Auto Mode.
[STOP] Button: Stops the air conditioning function.
USING THE PROGRAM
25
AHU
The following is the AHU control menu and features.
Item
Operation
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
[Schedule▶] Button: Move to Schedule menu.
Room
Display the current temperature.
Set Temperature
Mode
Click(Touch) [▲]/[▼] to set the temperature.
[COOL] Button: Operates with Cooling Mode.
[HEAT] Button: Operates with Heating Mode.
[FAN] Button: Purifies the air.
[DRY] Button: Dehumidifies the air during the rainy season or when
humidity is high.
yy [Drift] Button: Reduces energy consumption by operating in the most
efficient method possible.
yy
yy
yy
yy
AutoVent
yy [Set] Button: If the CO2 concentration level increases during cooling or
heating, increase the outdoor air volume to reduce the CO2 concentration
level.
yy [Clear] Button: Disables AutoVent.
Humidify
yy [Set] Button: Enables the humidifier function.
yy [Clear] Button: Disables the humidifier function.
[Detail. ▶] Button
Control details.
ENGLISH
GoTo
26
USING THE PROGRAM
• AHU Fine Control
ENGLISH
Item
Operation
Set
Mode
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
Click(Touch) [▲]/[▼] to set the temperature.
[COOL] Button: Operates with Cooling Mode.
[HEAT] Button: Operates with Heating Mode.
[FAN] Button: Purifies the air.
[DRY] Button: Dehumidifies the air during the rainy season or when
humidity is high.
yy [Drift] Button: Reduces energy consumption by operating in the most
efficient method possible.
yy
yy
yy
yy
AutoVent
yy [Set] Button: If the CO₂ concentration level increases during cooling or
heating, increase the outdoor air volume to reduce the CO₂ concentration
level.
yy [Clear] Button: Disables AutoVent.
CO2(ppm)
Use [▲]/[▼] to set the desired carbon dioxide emission level from 500 ppm
to 1,500 ppm in intervals of 100 ppm (CO₂ is not settable in some models.).
Humidify
Humidity(%)
Partial Lock
yy [Set] Button: Enables the humidifier function.
yy [Clear] Button: Disables the humidifier function.
Use [▲]/[▼] to set the desired humidity from 40% to 60% in intervals of 1%.
yy [Set] Button: Disables remote control for all features.
yy [Clear] Button: Disables the lock.
OA Damper
Use [▲]/[▼] to set the OA damper from 0° to 90° in intervals of 1°.
EA Damper
Use [▲]/[▼] to set the EA damper openness from 0° to 90° in intervals of 1°.
USING THE PROGRAM
Item
Description
MIX Damper
Use [▲]/[▼] to set the mix damper openness from 0° to 90° in intervals of 1°.
27
DOKIT
The following is the DOKIT control menu and features.
Operation
GoTo
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
[Schedule▶] Button: Move to Schedule menu.
AWHP
The following is the AWHP control menu and features.
Item
Operation
GoTo
Mode
Air/Water Temp.
Description
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
[Schedule▶] Button: Move to Schedule menu.
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum temperature.
yy [COOL] Button: Operates with Cooling Mode.
yy [HEAT] Button: Operates with Heating Mode.
(Indicated as air or water temperature depending on the product.)
Click(Touch) [▲]/[▼] to set the air/water temperature.
HotWater Temp.
Click(Touch) [▲]/[▼] to set the water heater temperature.
[Detail. ▶] Button
Control details.
ENGLISH
Item
28
USING THE PROGRAM
• AWHP Fine Control
ENGLISH
Item
Description
Operation
yy [ON] Button: Starts the operation of the device.
yy [OFF] Button: Stops the operation of the device.
Hotwater
yy [ON] Button: Enables the hot water function.
yy [OFF] Button: Disables the hot water function.
Partial Lock
Mode
Air/Water Temp.
Hot Water Temp.
yy [Set] Button: Disables remote control for all features.
yy [Clear] Button: Disable the lock.
yy [AUTO] Button: Evaluates the operating environment conditions and
automatically sets the optimum temperature.
yy [COOL] Button: Operates with Cooling Mode.
yy [HEAT] Button: Operates with Heating Mode.
(Indicated as air or water temperature depending on the product.)
Click(Touch) [▲]/[▼] to set the air/water temperature.
Click(Touch) [▲]/[▼] to set the water heater temperature.
USING THE PROGRAM
29
DO
The following is the DO control menu and features.
Item
Operation
yy [SHORT] Button: Short signal output.
yy [OPEN] Button: Open signal output.
[Schedule▶] Button: Move to Schedule menu.
ENGLISH
GoTo
Description
30
USING THE PROGRAM
Registering Floor Plan
In the Control/Monitor menu, you can register floor plans to identify and locate each device and
device group. On the floor plan, you can register space information as well as the location where a
device is installed.
1. In the main menu, click(touch) the [Control/Monitor] menu icon.
2. Select the device group you want to monitor from the group list.
• The monitoring screen for the device is displayed.
3. Click(Touch) [Drawing] button.
ENGLISH
4. Click(Touch) [Edit] button.
USING THE PROGRAM
31
5. [Add Drawing] button.
• The Open Floor Plan window is displayed.
ENGLISH
6. Select a desired floor plan from the Open Floor Plan window, then click(touch) [Confirm].
• The floor plan image is displayed.
Notes
You cannot open a floor plan if the file name is in other languages. Use English file names.
32
USING THE PROGRAM
7. In the device list, select a device you want to display on the floor plan and click(touch) the device
location on the plan.
• To delete a device from the plan, double-click(touch) its icon.
ENGLISH
8. To complete the registration of the floor plan, click(touch) the [Apply] button.
Notes
yy To add a floor plan, put image file to USB root directory or /mnt/flash/map directory.
yy To add a floor plan, you can only use jpg, gif, or png file formats.
yy To add a floor plan, a 2MB or less image size is recommended.
USING THE PROGRAM
33
Checking Floor Plan
In Control/Monitoring, you can check floor plans. On the floor plan, you can register space
information as well as the location where a device is installed.
1. In the main menu, click(touch) the [Control/Monitor] menu icon.
2. Select the device group you want to monitor from the group list.
• The monitoring screen for the device is displayed.
3. Click(Touch) [Drawing] button.
• The registered floor plan is displayed.
ENGLISH
34
USING THE PROGRAM
Editing the Floor Plan
You can edit a registered floor plan.
1. In the main menu, click(touch) the [Control/Monitor] menu icon.
2. Select the device group you want to monitor from the group list.
• The monitoring screen for the device is displayed.
3. Click(Touch) [Drawing] button.
ENGLISH
4. Click(Touch) [Edit] button.
5. To change floor plan, click(touch) [Change] button.
• The Open Floor Plan window is displayed.
6. Select a desired floor plan from the Open Floor Plan window, then click(touch) [Confirm].
• The floor plan image is displayed.
USING THE PROGRAM
35
7. To change the location of a device, click(touch) the icon of the device and then click(touch) the
location to which you want to move that device.
ENGLISH
8. To complete floor plan editing, click(touch) the [Apply] button.
Notes
yy To add a floor plan, put image file to USB root directory or /mnt/flash/map directory.
yy To add a floor plan, you can only use jpg, gif, or png file formats.
yy To add a floor plan, a 2MB or less image size is recommended.
36
USING THE PROGRAM
Deleting the Floor Plan
You can delete a registered floor plan.
1. In the main menu, click(touch) the [Control/Monitor] menu icon.
2. Select the device group you want to monitor from the group list.
• The monitoring screen for the device is displayed.
3. Click(Touch) [Drawing] button.
• The registered floor plan is displayed.
4. Click(Touch) [Edit] button.
5. To delete a floor plan, click(touch) the [Delete] button.
ENGLISH
6. When you are prompted to confirm the deletion, click(touch) [Confirm].
USING THE PROGRAM
37
Monitoring a Device
You can check the control state of registered devices.
1. In the main menu, click(touch) the [Control/Monitor] menu icon.
2. Select the device group you want to monitor from the group list.
• The monitoring screen for the device is displayed.
3. Click(Touch) a device you want to monitor.
4. Please check the device information in the monitoring screen.
• The information on the monitoring screen differs depending on the view type. For details
about the view types, refer to View Type on page 12.
ENGLISH
5. To check the control status of the device, click(touch) the [Detail. ] button.
38
USING THE PROGRAM
Schedule
The Schedule feature allows you to program the behavior of the devices. If a device must adhere to a
certain schedule, you can program the device to operate only at scheduled times. Scheduled devices
do not activate unless programmed to do so and are managed centrally. This can significantly reduce
energy consumption.
Schedule Screen composition and features
The following explains Schedule Screen composition and features.
①
②
③
④
ENGLISH
⑤
Number
Item
①
[Today] Button
②
Dates
③
View Type
④
[Total] Button
⑤
Calendar
⑥
⑦
Description
Display today's date, the current week, or the current
month.
yy Displays the selected date.
yy Use [◀]/[▶] to move to the previous/next date.
yy [W] Button: Converts to Week View.
yy [M] Button: Converts to Month View.
View full schedule list.
yy Displays the schedules for the selected dates.
yy Today's date is marked in light blue.
USING THE PROGRAM
Number
Item
Schedule List
⑥
⑦
[Add a Schedule]
Button
39
Description
Displays registered schedules by name.
Registers new schedules.
Creating Schedules
You can configure and add a schedule for a device.
1. In the main menu, click(touch) [Schedule] menu icon.
2. Click(Touch) [Add a Schedule] Button.
• The Add Schedule window opens.
• The selected device is displayed in the applied device area of the control command
configuration.
ENGLISH
3. In the group list, click(touch) a device for which a schedule is applied.
40
USING THE PROGRAM
4. Configure the schedule information that controls the device.
ENGLISH
Item
Schedule Name
Time
Period
Description
Click(Touch) the input box. Enter the name for the schedule.
yy Click(Touch) the time area and then the [+]/[-] button to select the
desired time.
yy Click(Touch) the [AM]/[PM] button to select before or after midday.
Click(Touch) the period area and then the [+]/[-] button to select the
desired period.
Click(Touch) the Repetition Pattern area and select a desired pattern.
Repeat Pattern
Select day
yy
yy
yy
yy
yy
Select Day: Selected days the schedule will be performed.
Once: Applies a schedule once on a selected date.
Everyday: Applies the same schedule Everyday.
Mon - Fri: Applies a schedule repeatedly from Monday to Friday.
Mon - Sat: Applies a schedule repeatedly from Monday to
Saturday.
Click(Touch) a desired day to apply a schedule.
USING THE PROGRAM
41
5. Click(Touch) the device icon of the applied device.
• The control configuration window for the device is displayed. The control configuration
window differs depending on the device.
• The control list configured in the Command Summary area is displayed.
7. To complete the schedule configuration, click(touch) the [Confirm] button.
ENGLISH
6. Configure the device control status, then click(touch) the [Confirm] button.
42
USING THE PROGRAM
Checking Schedules
You can check registered schedules.
1. In the main menu, click(touch) the [Schedule] menu icon.
2. In the Date area, click(touch) the [◀]/[▶] button to select a schedule search period.
• The number of schedules are displayed for the selected date.
ENGLISH
3. To check schedule details, click(touch) a schedule you want to check in the schedule list.
• Schedule details are displayed.
USING THE PROGRAM
43
Editing Schedules
You can modify the content of a registered schedule as follows.
1. In the main menu, click(touch) the [Schedule] menu icon.
2. Click(Touch) a schedule you wish to modify from the schedule list.
• Schedule details are displayed.
3. Click(Touch) the [Edit] button.
• The schedule configuration screen is displayed.
ENGLISH
4. Modify the schedule information and device control configuration, then click(touch) the [Confirm]
button.
• The changed data will be saved.
44
USING THE PROGRAM
Deleting Schedules
You can delete a registered schedule as follows.
1. In the main menu, click(touch) the [Schedule] menu icon.
2. Click(Touch) a schedule you wish to delete from the schedule list.
• Schedule details are displayed.
3. Click(Touch) the [Delete] button.
ENGLISH
4. When you are prompted to confirm the deletion, click(touch) [Confirm].
• The selected schedule is deleted.
USING THE PROGRAM
45
Auto Logic
Auto Logic allows the system to automatically control the power consumption of external devices.
You can also set the indoor temperature to automatically adjust to outdoor conditions or activate
devices for certain periods of time.
Notes
If you set a device control value in the auto logic status view, the device can operate based on
that value.
Peak control limits peak power consumption. You can set the target operating rate so that total power
consumption does not exceed the set limit. To prevent power consumption from exceeding the limit,
the system will automatically change cooling mode to fan mode and cancel heating mode.
Notes
Depending on the installation site specifications, either the peak control or demand control
functions can be selected. Go to Environment > Advance Setting > Peak/Demand Set and
select a desired control type.
ENGLISH
Peak Control
46
USING THE PROGRAM
Editing Groups
The auto logic designates the registered devices as a group and controls them by group. The
following explains how to create groups and how to edit the created groups.
Adding Groups
You can create a group as follows.
1. In the main menu, click(touch) the [AutoLogic > Peak Control] menu icons.
2. Click(Touch) the [Edit Group] button.
• The screen converts to Edit Group.
3. Click(Touch) the [Add Group] button.
ENGLISH
Notes
By click(touch)ing [Apply default group], you can create a group automatically based on
the group and indoor unit configuration set in the Device Management menu.
4. When the window to input a group name is displayed, enter a group name and click(touch) the
[Confirm] button.
• The group is added to the group list.
5. In the group list, click(touch) the group added in Step 4.
USING THE PROGRAM
47
6. In the non-registered device area, click(touch) a device to add to the new group and click(touch)
the [Add] button.
• The selected device is moved to the registered device area.
ENGLISH
Notes
Peak control is only limited to indoor devices, therefore you cannot register other devices such
as the ERV, AHU or AWHP.
7. To complete group creation, click(touch) the [Apply] button.
48
USING THE PROGRAM
Changing Group Name
You can change the name of a registered group as follows.
1. In the main menu, click(touch) the [AutoLogic > Peak Control] menu icon.
2. Click(Touch) the [Edit Group] button.
• The screen converts to Edit Group.
3. In the group list, click(touch) a group whose name you want to change and click(touch) the
[Rename] button.
ENGLISH
4. Enter a new group name and click(touch) the [Confirm] button.
• The group name is now changed.
5. To complete group rename, click(touch) the [Apply] button.
USING THE PROGRAM
49
Deleting Groups
You can delete a registered group.
1. In the main menu, click(touch) the [AutoLogic > Peak Control] menu icon.
2. Click(Touch) the [Edit Group] button.
• The screen converts to Edit Group.
3. In the group list, click(touch) a group to be deleted and click(touch) the [Del Group] button.
ENGLISH
4. When you are prompted to confirm the deletion, click(touch) [Confirm].
• The selected group is deleted and the tab removed.
Notes
yy The group configured in Peak Control is also applied to Demand Control.
yy If you change the group configuration in the device management menu, the group configured
in Peak Control is initialized.
50
USING THE PROGRAM
Configuring Peak Control
You can configure Peak Control as follows.
1. In the main menu, click(touch) the [AutoLogic > Peak Control] menu icon.
2. Select the control status in the control configuration area.
①
②
ENGLISH
③
④
Number
Item
①
Group List
⑤
Description
Displays the device group list and group priority.
Configures Peak Control configuration and details.
yy Operation Status
②
Control
Configuration
Area
-- Can be configured in [Environment > Advance
Setting].
-- Priority Control: Control based on group priority
-- Outdoor Unit Control: Controls based on outdoor
unit capacity limit.
USING THE PROGRAM
Number
Item
51
Description
(Operation Status - Priority Control selected)
yy Operation
-- [Run] Button: Operates the device.
-- [Stop] Button: Stops the operation of the device.
②
Control
Configuration
Area
yy Shift Time(Min.): Click(Touch) [▲]/[▼] to set the time
in minutes to force the operation to switch over.
yy Target ratio(%): Click(Touch) [▲]/[▼] or drag to set
the target rate.
yy Current Running(%): Displays the current rate.
(Operation Status - Outdoor unit capacity control selected)
-- [Run] Button: Operates the device.
-- [Stop] Button: Stops the operation of the device.
yy Target ratio(%): Click(Touch) [▲]/[▼] or drag to set
the target rate.
③
[Edit Group]
Button
④
[Cancel] Button
Cancels control configuration.
⑤
[Apply] Button
Applies control configuration.
Edit a control group.
3. To complete configuration, click(touch) the [Apply] button.
ENGLISH
yy Operation
52
USING THE PROGRAM
Configuring Priority
1. In the main menu, click(touch) the [AutoLogic > Peak Control] menu icon.
2. In the group list, click(touch) the priority icon ( ) of the group in question and then select a
desired priority.
ENGLISH
Notes
Basically, a newly added group has the highest priority. If a group is added, re-configure the
priority for all groups.
USING THE PROGRAM
53
Checking Peak Control Status
You can check the Peak Control configuration status as follows.
1. In the main menu, click(touch) the [AutoLogic > Peak Control] menu icon.
2. Check how Peak Control is configured.
ENGLISH
54
USING THE PROGRAM
Item
Description
Configure Peak Controls.
yy Operation Status
-- Can be configured in [Environment > Advance Setting].
-- Priority: Controls based on group priority
-- Outdoor unit capacity control: Controls based on outdoor unit
capacity limit.
(Operation Status - Priority Control selected)
Control
Configuration
Area
yy Operation
-- [Run] Button: Operates the device.
-- [Stop] Button: Stops the operation of the device.
ENGLISH
yy ShiftTime(Min.): The cycle by which the operation switches over.
yy Target ratio(%): Displays the target operation rate.
yy Current Running(%): Displays the current rate.
(Operation Status - Outdoor unit capacity control selected)
yy Operation
-- [Run] Button: Operates the device.
-- [Stop] Button: Stops the operation of the device.
yy Target ratio(%): Displays the target operation rate.
USING THE PROGRAM
55
Demand Control
After observing changes in power consumption, this feature can prevent power consumption from
exceeding a set limit. If you set the demand control and the program predicts that power consumption
will exceed that limit, it will begin deactivating less important devices to save energy.
Notes
yy For demand, depending on the installation site specifications, either the peak control or
demand control functions can be selected. Go To Environment > Advance Setting > Peak/
Demand Settings and select a desired control type.
yy In the Demand Control menu, you can only check the Demand Control status. You cannot
configure the operation, operation switchover cycle, desired rate, current rate, etc.
ENGLISH
yy For outdoor capacity control, depending on the installation site specifications, either the peak
control or demand control functions can be selected.
56
USING THE PROGRAM
Checking Demand Control Status
You can check the Peak Control configuration status as follows.
1. In the main menu, click(touch) the [AutoLogic > Demand Control] menu icon.
2. Check how Demand Control is configured.
ENGLISH
①
Number
Item
①
Comm. Status
with Demand
Controller
②
Description
Displays the communication status between demand
controller and Central Controller.
Checks the demand configuration details.
yy Operation Status
②
Control
Configuration
Area
-- Can be configured in [Environment > Advance
Setting].
-- Priority Control: Control based on group priority
-- Outdoor Unit Control: Controls based on outdoor
unit capacity limit.
USING THE PROGRAM
Number
Item
57
Description
(Operation Status - Priority Control selected)
yy Operation
-- [Operate] Button: Operates the device.
-- [Stop] Button: Stops the operation of the device.
②
Control
Configuration
Area
yy Shift Time(Min.): The cycle by which the operation
switches over.
yy Target ratio(%): Displays the target operation rate.
yy Current Running(%): Displays the current rate.
(Operation Status - Outdoor unit capacity control selected)
yy Operation
-- [Stop] Button: Stops the operation of the device.
yy Target ratio(%): Displays the target operation rate.
ENGLISH
-- [Run] Button: Operates the device.
58
USING THE PROGRAM
Time-limit Operation
The time-limit operation is to limit the amount of time the devices (indoor unit, ERV, DOKITs, AWHP,
and AHU) are running individually. By setting the device operation time in advance, you can control
for how long a device works and have it stop automatically.
Editing Groups
The auto logic designates the registered devices as a group and controls them by group. The
following explains how to create groups and how to edit the created groups.
Adding Groups
ENGLISH
You can create a group as follows.
1. In the main menu, click(touch) the [AutoLogic > TimeLimitControl] menu icon.
2. Click(Touch) the [Edit Group] button.
• The screen converts to Edit Group.
3. Click(Touch) the [Add Group] button.
Notes
By click(touch)ing [Apply default group], you can create a group automatically based on
the group and indoor unit configuration set in the Device Management menu.
4. When the window to input a group name is displayed, enter a group name and click(touch) the
[Confirm] button.
• The group is added to the group list.
USING THE PROGRAM
59
5. In the group list, click(touch) the group added in Step 4.
6. In the non-registered device area, click(touch) a device to add to the new group and click(touch)
[Add] button.
• The selected device is moved to the registered device area.
ENGLISH
Notes
For the time-limit operation, you cannot register DI/DO.
7. To complete group creation, click(touch) the [Apply] button.
60
USING THE PROGRAM
Changing Group Name
You can change the name of a registered group as follows.
1. In the main menu, click(touch) the [AutoLogic > TimeLimitControl] menu icon.
2. Click(Touch) the [Edit Group] button.
• The screen converts to Edit Group.
3. In the group list, click(touch) a group whose name you want to change and click(touch) the
[Rename] button.
ENGLISH
4. Enter a new group name and click(touch) the [Confirm] button.
• The group name is now changed.
5. To complete group rename, click(touch) the [Apply] button.
USING THE PROGRAM
61
Deleting Groups
You can delete a registered group.
1. In the main menu, click(touch) the [AutoLogic > TimeLimitControl] menu icon.
2. Click(Touch) the [Edit Group] button.
• The screen converts to Edit Group.
3. In the group list, click(touch) a group to be deleted and click(touch) the [Del Group] button.
ENGLISH
4. When you are prompted to confirm the deletion, click(touch) [Confirm].
• The selected group is deleted and the tab removed.
5. To complete group delete, click(touch) the [Apply] button.
62
USING THE PROGRAM
Configuring Time-Limit Operation
1. In the main menu, click(touch) the [AutoLogic > TimeLimitControl] menu icon.
2. In the group configuration status area, click(touch) a group to be controlled.
• The device list, status information, and condition details of the group are displayed.
ENGLISH
3. Select the control status in the conditions configuration area.
Item
Description
Choosing whether to run Time-Limit Operation
Oper
Hours to Off(Hour)
Days
yy [Run] Button: Run the time-limit operation.
yy [Stop] Button: Stops the time-limit operation.
yy Select the operation time limit of an operation group.
yy The devices included in the group operates for the
selected time then stops automatically.
Select a day on which to run the time-limit operation.
USING THE PROGRAM
63
4. To run the time-limit operation on the group, in the group configuration operation status area,
click(touch) the [disable] button.
• The button changes to [enable].
ENGLISH
5. To complete the configuration, click(touch) the [Apply] button.
Notes
If you change the operation stop standby time, it takes about 15 seconds to apply it.
64
USING THE PROGRAM
InterLocking
You can integrate the system with external devices, like remote shutdown, to halt the operation of
all indoor units and ERV. For InterLocking, you should create a pattern for devices and apply the
control configuration. The following explains how to create and manage a pattern and control device
integration.
Managing Pattern
The following explains how to register integrated devices as a pattern and how to modify or delete a
registered pattern.
ENGLISH
Adding Pattern
You can add a pattern as follows.
1. In the main menu, click(touch) the [AutoLogic > InterLocking] menu icon.
2. Click(Touch) the [Add] button.
• A window to create a pattern is displayed.
3. Type a new pattern name in the pattern name input window.
4. Click(Touch) the [Input Device] tab.
USING THE PROGRAM
65
5. In the non-registered device area, click(touch) a device to be registered and click(touch) the
[Add] button.
ENGLISH
6. In the input device list, click(touch) the device you want to trigger control.
7. Select a control status in the control configuration area.
8. Click(Touch) the [Output Device] tab.
9. In the non-registered device area, click(touch) a device to be registered and click(touch) the
[Add] button.
10.In the output device list, click(touch) the device you want to control.
66
USING THE PROGRAM
11. Select a control status in the control configuration area.
12.To complete the adding of a pattern, click(touch) the [Apply] button.
Editing Pattern
You can edit a pattern as follows.
1. In the main menu, click(touch) the [AutoLogic > InterLocking] menu icon.
2. Select a pattern and click(touch) the [Edit] button.
• The pattern editing screen opens.
3. Modify the pattern configuration information and click(touch) the [Apply] button.
Deleting Pattern
ENGLISH
You can delete a pattern as follows.
1. In the main menu, click(touch) the [AutoLogic > InterLocking] menu icon.
2. Select a pattern to be deleted and click(touch) the [Delete] button.
3. When you are prompted to confirm the deletion, click(touch) [Confirm].
• The selected pattern is deleted.
USING THE PROGRAM
67
Checking InterLocking
1. In the main menu, click(touch) the [AutoLogic > InterLocking] menu icon.
2. Click(Touch) a pattern for which you want check the device integration.
• The device integration status for the pattern is displayed.
ENGLISH
68
USING THE PROGRAM
Statistics
The following explains how to use statistics and graphs to check the power consumption and
operation time of a device.
Statistics Screen Composition and Features
The following explains the statistics screen composition and features.
①
②
③
④
⑤
ENGLISH
⑥
⑦
Number
Item
①
Group List
②
③
Statistics Items
Query Unit
⑧
⑨
Description
Displays the device group list.
yy [Power] Button: You can check the power
consumption of each group and total power
consumption.
yy [RunTime] Button: You can check the operating
time and the total operating time of indoor units
in each group.
yy [Monthly] Button: Queries on monthly consumption
within the last four months.
yy [Daily] Button: Queries on daily consumption within
the query period.
USING THE PROGRAM
Number
Item
Description
④
Query Period
Selection Area
yy Selects the period for which you want to query
statistics details for daily.
yy The start date should be no more than 31days before
the end date.
Displays Statistics
Information
yy Statistics data per period: Displays power
consumption per unit of query or operation time
statistics and graphs.
yy Power consumption: Displays power consumption
and use time.
⑤
69
Converting Statistics Data View
[Table]/[Graph]
Button
⑦
[Initial Date]
Button
yy Selects Statistics Reference Date.
yy Move to Settings > General Settings > Statistics
Reference Date.
[Email] Button
yy ACP, ACP Lonworks, AC Smart Premium: Sends
the queried statistics data to the Email address
registered in the Preference menu.
yy ACP BACnet: Not supported.
[Save to PC] or
[Save to USB]
button
yy ACP, ACP Lonworks: Save the statistics data to a
PC.
yy AC Smart Premium (Web): Save the statistics data
to a PC.
yy AC Smart Premium (Controller): Save the statistics
data to a USB memory stick.
yy ACP BACnet: Not supported.
⑧
⑨
Querying Statistics
You can query the power consumption of a device or operation time statistics data as follows.
1. In the main menu, click(touch) the [Statistics] menu icon.
2. Click(Touch) the device group you want from the group list.
3. Click(Touch) the button of the statistics item you want.
• [Power] Button: You can check the power consumption of each group and total power
consumption.
• [RunTime] Button: You can check the operating time and the total operating time of indoor
units in each group.
ENGLISH
yy Table: Views the queried statistics data in a table
format.
yy Graph: Views the queried statistics data in a graphic
format.
⑥
70
USING THE PROGRAM
4. In the query period selection area, click(touch) the date button and [+]/[-] button to select the
desired period.
• The start date should be no more than 31days for daily before the end date. The query period
for monthly is automatically fixed to the last four months.
5. Check the statistics details in the statistics information display area.
• To change the statistics information view type, click(touch) the [Table] or [Graphic] button.
ENGLISH
6. To send the statistics data by email, click(touch) the [Email] button. To save it to a PC or a USB
memory stick, click(touch) the [Save to PC] or [Save to USB] button.
Notes
The statistics data is stored up to 6 months.
Notes
yy Devices which can query the Run Time: Indoor units
yy Devices which can query the Power consumption: devices which can be used with the PDI
(For further information about the devices can be used with the PDI, please refer to the PDI
manual.)
USING THE PROGRAM
71
Report
The following explains how to query the device control information or error information.
Report screen composition and features
The following explains the report screen composition and features.
①
②
③
ENGLISH
④
Number
⑤
Item
⑥
Description
Selects report query items.
①
Report Items
②
Query Period
Selection Area
③
Report detail display
area
④
[Delete Report]
Button
yy [Total] Button: Queries all reports regarding control
and error.
yy [Control] Button: Queries control related reports
only.
yy [Error] Button: Queries error related reports only.
yy Selects the period for which you want to query
report details.
yy The starting date should be no more than three
months from the ending date.
Displays the reports related to control and error.
Deletes the selected report.
72
USING THE PROGRAM
Number
⑤
⑥
Item
Description
[Send Email] Button
yy ACP, ACP Lonworks, AC Smart Premium: Sends
the queried reports to the Email address registered
in the Preference menu.
yy ACP BACnet: Not supported.
[Save to PC] or
[Save to USB]
button
yy ACP, ACP Lonworks: Save the reports to a PC.
yy AC Smart Premium (Web): Save the reports to
a PC.
yy AC Smart Premium (Controller): Save the
reports to a USB memory stick.
yy ACP BACnet: Not supported.
ENGLISH
USING THE PROGRAM
73
Querying Report
You can query the device control or error report as follows.
1. In the main menu, click(touch) the [Report] menu icon.
2. In the report item, click(touch) an item for which you want to query a report.
• [Total] Button: Queries all reports regarding control and error.
• [Control] Button: Queries control related reports only.
• [Error] Button: Queries error related reports only.
3. In the query period selection area, click(touch) the date button and [+]/[-] button to select the
desired period.
• The starting date should be no more than three months from the ending date.
4. Check the report details in the report detail display area.
ENGLISH
5. To send the report detail by email, click(touch) the [Send Email] button. To save it to a PC or a
USB memory stick, click(touch) the [Save to PC] or [Save to USB] button.
Caution
You can query up to 200 reports and email/save to USB memory up to 300 reports. Up to 5000
reports are stored.
74
USING THE PROGRAM
Installing
You can add a device or change the settings of a registered device.
Registering Device
After installing Central Controller, log into Central Controller to register the devices to be connected.
Central Controller can register a device by using one of two methods.
• Registering Device Automatically
• Registering Device Manually
ENGLISH
Notes
To register a device on Central Controller, you should login with administrator permissions.
If you have logged in already with standard user permissions, you cannot proceed with this
process any further.
USING THE PROGRAM
75
Registering Device Automatically
Devices connected to Central Controller are automatically searched for and registered. You can
register a device automatically as follows.
1. In the main menu, click(touch) the [Installing] menu icon.
2. Click(Touch) the [Installing] tab.
3. Click(Touch) the [Auto Search] button.
ENGLISH
Notes
Please turn the screen saver off before [Auto Search].
4. When you are prompted to confirm the setting, click(touch) [Confirm].
• It takes 5 to 10 minutes to register a device automatically. Please turn the screen saver off
before [Auto Search]
76
USING THE PROGRAM
5. To save the searched devices, click(touch) the [Apply] button.
• Device registration is completed. 2 DIs and 2 DOs are always added to the Unit Status area
as they are part of the Central Controller hardware.
Registering Device Manually
Devices connected to Central Controller can be registered by the user by entering relevant
information. You can register a device manually as follows.
1. In the main menu, click(touch) the [Installing] menu icon.
2. Click(Touch) the [Installing] tab.
3. Type the device information and click(touch) the [Insert] button.
ENGLISH
Item
Description
Selects a device type.
Device Type
Unit Name
(20 Characters)
yy IDU(indoor unit,), ODU(Outdoor unit,), ERV(Energy Recovery Ventilator ),
ERV DX(Direct Expansion Energy Recovery Ventilator ), DI/DO, DOKIT,
AWHP, or AHU
Enter the device name.
yy Up to 20 characters.
Type the central control of the device.
Address
(00-FF)
Model
(20 Characters)
yy A central control value is a number between 00 and FF. You cannot
type the same value for similar devices.
yy You cannot enter a duplicate value for indoor devices and DOKIT.
Type the device model.
yy Up to 20 characters.
USING THE PROGRAM
Item
77
Description
Type the maximum power consumption of the device.
Capacity
(5-digit)
yy Up to 5 characters.
yy The power consumption value of the actual device cannot exceed
the input value.
4. To save the device, click(touch) the [Apply] button.
• Device registration is completed.
Changing Device
You can change the settings of registered devices.
• The device information is displayed in the device information input box.
4. Type the device information and click(touch) the [Modify Unit] button.
• The changed device information is applied.
5. To save a change, click(touch) the [Apply] button.
Deleting Device
Follow these steps to delete a device from the list.
1. In the main menu, click(touch) the [Installing] menu icon.
2. Click(Touch) the [Installing] tab.
3. In the device list, click(touch) a device to be deleted and click(touch) the [Del Unit] button.
4. When you are prompted to confirm the deletion, click(touch) [Confirm].
• The selected device is deleted from the list.
5. To save a change, click(touch) the [Apply] button.
ENGLISH
1. In the main menu, click(touch) the [Installing] menu icon.
2. Click(Touch) the [Installing] tab.
3. Click(Touch) a device to be changed in the device list.
78
USING THE PROGRAM
Managing Device
The following explains how to manage the information for a device added to the system.
Adding Groups
Follow these steps to add a new group.
1. In the main menu, click(touch) the [Installing] menu icon.
2. Click(Touch) the [Grouping] tab.
3. Click(Touch) the [Add Group] button.
4. When the window to type a group name is displayed, enter a group name and click(touch) the
[Confirm] button.
ENGLISH
• The group is added to the group list.
5. In Grouping, click(touch) the group added in Step 4.
USING THE PROGRAM
79
6. In the non-registered device area, click(touch) a device to add to the new group and click(touch)
the [Add] button.
• The selected device is moved to the registered device area.
ENGLISH
7. To complete group creation, click(touch) the [Apply] button.
• When all non-registered devices are registered, the [Apply] button is enabled.
80
USING THE PROGRAM
Changing Group Name
You can change the name of a registered group as follows.
1. In the main menu, click(touch) the [Installing] menu icon.
2. Click(Touch) the [Grouping] tab.
3. In the device management list, click(touch) a group whose name you want to change and
click(touch) the [Rename] button.
ENGLISH
4. Enter a new group name and click(touch) the [Confirm] button.
• The group name is changed.
USING THE PROGRAM
81
Deleting Groups
You can delete a registered group.
1. In the main menu, click(touch) the [Installing] menu icon.
2. Click(Touch) the [Grouping] tab.
3. In the device management list, click(touch) a group to be deleted and click(touch) the [Del
Group] button.
ENGLISH
4. When you are prompted to confirm the deletion, click(touch) [Confirm].
• The selected group is deleted and the tab removed.
82
USING THE PROGRAM
Environment
The following explains how to configure the system environment for user convenience and how to
check an already configured environment.
ENGLISH
<ACP>
<ACP Lonworks>
<ACP BACnet>
<AC Smart Premium>
Item
ACP
ACP Lonworks
ACP BACnet
AC Smart
Premium
General Setting
O
O
O
O
Screen Setting
X
X
X
O
Advance Setting
O
O
O
O
Customer Setting
O
O
O
O
Network Setting
X
X
X
O
E-Mail Setting
O
O
X
O
TMS Setting
O
O
O
O
Channel Setting
O
O
X
O
USING THE PROGRAM
83
General Setting
The following explains how to configure the general system environment.
ENGLISH
Item
Description
Language
Configures the language displayed on the screen
(한국어(Korean)/ English/ Italiano/ Españo/ Português/ pусский
язык/ Français/ Deutsch Sprache/ Türkçe/ Język Polski)
Time setting
Configures system time.
Date setting
Configures system date.
Temperature display
Initial date for statistics
Rates per 1kWh
Configures the temperature unit.
Configures the reference date for querying statistical data.
Configures the charge per 1kWh and currency.
Holiday setting
(The day schedule is
not work)
Selects the days for which schedules are not be applied.
Version Information
Displays the current software version.
84
USING THE PROGRAM
Language
Configures the language displayed on the screen.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Language.
4. Click(Touch) a language you want.
• The selected language is applied as the system language.
ENGLISH
USING THE PROGRAM
85
Time setting
You can configure the time used for the system as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Time setting.
4. Apply the current time and click(touch) the [Apply] button.
• Click(Touch) [+]/[-] button to select the time.
• Click(Touch) the [AM]/[PM] button to select before or after midday.
ENGLISH
Date setting
You can configure the date used for the system as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Date setting.
4. Modify the pattern configuration information and click(touch) the [Apply] button.
• Use [+]/[-] button to select a date.
86
USING THE PROGRAM
Temperature display
You can select a temperature system as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Temperature display.
4. Click(Touch) the temperature system you want.
• When selecting the Celsius system, in the Minimum Celsius(℃) Temperature window,
click(touch) the minimum temperature.
ENGLISH
USING THE PROGRAM
87
Initial date for statistics
Statistics Reference Date is the date for calculating the indoor unit's operation time by month.
The operation time from this date through the previous date to the same date of the next month is
calculated and provided as statistical data. You can configure Statistics Reference Date as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Initial date for statistics.
4. [+]/[-] button to select a date you want and [Apply] button.
ENGLISH
Rates per 1kWh
You can configure the charge per kWh and the currency as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Rates set.
4. Configure the charge/kWh configuration information and click(touch) [Apply] button.
• rates per(1kWh): Charge per 1kWh.
• Currency: Click(Touch) [▼] button to select the desired currency.
88
USING THE PROGRAM
Holiday setting(The day schedule is not work)
The following explains how to register an exception date or how to delete a registered date.
Adding Exception Date
You can add a desired exception date as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Holiday setting(Days in which the schedule is
ignored).
• The Exception Date Configuration window opens.
ENGLISH
4. Type a name for the exception date in the exception date input box.
5. [+]/[-] button to select an exception date.
6. To add the selected exception date, click(touch) [Add].
• The exception date is registered on the exception date list.
7. To complete Exception Date Configuration, click(touch) the [Apply] button.
USING THE PROGRAM
89
Deleting Exception Date
You can delete a registered exception date as follows.
1. In the main menu, click(touch) the [Environment]menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Holiday setting(Days in which the schedule is
ignored).
• The Exception Date Configuration window opens.
ENGLISH
4. Click(Touch) an exception date in the exception date list, and click(touch) the [Delete] button.
5. To complete Exception Date Configuration, click(touch) the [Apply] button.
Version Information
You can check the current version of the software as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) General Setting.
3. In the detailed settings list, click(touch) Version Information.
• The current version of the system is displayed in a popup window.
90
USING THE PROGRAM
Screen Setting (AC Smart Premium Only)
The following explains how to configure the use environment regarding the product screen.
ENGLISH
Item
Setting a Screen saver
Description
Determines whether to use a screen saver
Screen saver
Configures information to be displayed on the screen saver
(operation status)
Waiting time (minutes)
Select the standby time that the screen saver waits before
operation.
Speaker setting
Monitor power settings
Determines whether to use a speaker
Determines whether to use monitor power-off function
Turn off the monitor
waiting time(minutes)
Selects the standby time that the monitor waits before turn-off
Calibrating the Screen
Screen calibration for accurate click(touch)
USING THE PROGRAM
91
Setting a Screen saver
You can configure the screen saver as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Screen Setting.
3. In the detailed settings list, click(touch) Setting a Screen saver.
• Enable, the check box turns red and the Screen Saver and Waiting time (minutes) are
enabled.
ENGLISH
92
USING THE PROGRAM
Waiting time (minutes)
You can configure the standby time that the screen saver waits before operation.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Screen Setting.
3. In the detailed settings list, click(touch) the Waiting time (minutes).
4. In the Standby Time Configuration window, click(touch) the standby time.
ENGLISH
USING THE PROGRAM
93
Speaker setting
You can configure the speaker setting as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the setting list, click(touch) Screen Setting.
3. In the detailed settings list, click(touch) Speaker setting.
• Enable, the check box turns red and the Speaker is enabled.
ENGLISH
94
USING THE PROGRAM
Monitor power settings
You can configure the monitor to turn off automatically, if the click(touch) screen is not used for a
certain period of time. You can configure this function as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Screen Setting.
3. In the detailed settings list, click(touch) Monitor power settings.
• Enable, the check box turns red and Turn off the monitor waiting time (minutes) is
enabled.
ENGLISH
USING THE PROGRAM
95
Turn off the monitor waiting time (minutes)
You can configure the monitor to turn off automatically, if the click(touch) screen is not used for a
certain period of time, as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Screen Setting.
3. In the detailed settings list, click(touch) Turn off the monitor waiting time (minutes).
4. Click(Touch) the standby time you desire.
ENGLISH
Calibrating the Screen
You can calibrate the screen for accurate click(touch) response as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Screen Setting.
3. In the detailed settings list, click(touch) Calibrating the Screen.
4. To start the screen calibration, click(touch) the [Start screen calibration] button.
5. When the crosses appear on the screen, click(touch) the center of each to calibrate.
96
USING THE PROGRAM
Advance Setting
The following explains how to configure the functions necessary for device operation.
ENGLISH
Item
LGAP setting
(AC Smart Premium
Only)
Description
yy Master: Central Controller is used independently.
yy Slave: It shares the communication line with other central
controller products.
(If multiple Central Controllers are used, one should be selected as
Master and the others as Slave. In slave mode, some functions of
Auto Search in the Installing menu are not available.)
Peak/Demand set
yy Peak Control: You can use the peak control feature in the auto
logic menu.
yy Demand Control: You can use the demand control feature in
the auto logic menu.
Set the operation
mode
yy Priority Control: In Peak/Demand Control menu, control the
devices based on the priority of the group.
yy Outdoor Unit Capacity Control: In the Peak/Demand
Control menu, control the outdoor capacity rate per unit.
Temperature
difference
for Setback/
AutoChangeOver
Update S/W
DB backup
Recovery DB
[+]/[-] button to select the temperature gap.
yy Software upgrade using a USB memory stick.
yy Complete upgrade and restart the system.
Backup the DB onto a USB memory stick.
Use the DB stored on the USB memory stick to restore the system.
USING THE PROGRAM
97
LGAP setting
Central Controller can interface with another central controller to control a device. You can configure
the interface type with other devices as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Advance Setting.
3. In the detailed settings list, click(touch) LGAP setting.
4. Click(Touch) a type you want.
• Master: Central Controller is used independently.
• Slave: It shares the communication line with other central controller products.
ENGLISH
Notes
If multiple Central Controllers are used, one should be selected as Master and the others as
Slave.
Peak/Demand set
You can select a control type to be used for auto logic.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Advance Setting.
3. In the detailed settings list, click(touch) Peak/Demand set.
4. Click(Touch) a control type to be used for auto logic
• Peak Control: You can use the peak control feature in the auto logic menu.
• Demand Control: You can use the demand control feature in the auto logic menu.
98
USING THE PROGRAM
Set the operation mode
You can configure the operation type as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Advance Setting.
3. In the detailed settings list, click(touch) Set the operation mode.
4. Click(Touch) an operation type you want.
ENGLISH
Temperature difference for Setback/AutoChangeOver
You can configure the temperature gap for auto changeover operation.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Advance Setting.
3. In the detailed settings list, click(touch) Temperature difference for Setback/
AutoChangeOver.
4. [+]/[-] button to select a temperature gap you want and [Apply] button.
USING THE PROGRAM
99
Update S/W
You can upgrade the current version of software as follows.
Notes
yy To update the software, you need a USB memory stick which has patch.tar file in the ramdisk
folder.
yy For standard thumb drives, a USB to mini USB cable is required.
• When the update has been completed, the program restarts.
ENGLISH
1. Connect the USB memory to Central Controller.
2. In the main menu, click(touch) the [Environment] menu icon.
3. In the Settings list, click(touch) Advance Setting.
4. In the detailed settings list, click(touch) Update S/W.
5. When the software update window appears, click(touch) the [Update S/W] button.
100
USING THE PROGRAM
DB backup
You can backup the database stored in the system to USB memory as follows.
1. Connect the USB memory to Central Controller.
2. In the main menu, click(touch) the [Environment] menu icon.
3. In the Settings list, click(touch) Advance Setting.
4. In the detailed settings list, click(touch) DB backup.
5. When the DB Backup window appears, click(touch) the [DB backup] button.
ENGLISH
Recovery DB
You can use the database stored on USB memory to restore the system database.
1. Connect the USB memory stick to Central Controller.
2. In the main menu, click(touch) the [Environment] menu icon.
3. In the Settings list, click(touch) Advance Setting.
4. In the detailed settings list, click(touch) Recovery DB.
5. When the DB Recovery window appears, click(touch) the [Recovery DB] button.
• When the DB recovery has been completed, the program restarts.
USING THE PROGRAM
101
Customer Setting
Only the administrator account can change user environments.
ENGLISH
Item
Change Password
Add user
User Management
Description
Only the administrator account can change the password.
Add up to 30 new system users.
yy [Delete] Button: Deletes a user.
yy [Edit] Button: Changes user information.
102
USING THE PROGRAM
Change Password
The system_admin account password can be changed as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Customer Setting.
3. In the detailed settings list, click(touch) Change Password.
4. After entering the current and new passwords, click(touch) [Confirm].
• Current P/W: Enter the current password.
• New P/W: Enter the new password for system_admin..
• Re-type P/W: Enter the new password to confirm that the new password has been entered
correctly.
ENGLISH
USING THE PROGRAM
103
Add user
You can add a user as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Customer Setting.
3. In the detailed settings list, click(touch) Add User.
4. When the system password input window appears, enter the password and click(touch) [Confirm].
[Confirm].
• ID: Enter the user's ID for the email server.
• Password: Enter the login password.
• Password 'Confirm': Re-enter the password.
• User Role: Select the user permission you want
• Accessable Group: Select a controllable device group
Notes
Use is limited depending on the user.
yy General user menu: Control/Monitor, Schedule, Statistics for assigned Groups/Units
yy Administrator menu: Control/Monitor, Schedule, AutoLogic, Statistics, Report, Installing for all
Groups/Units
ENGLISH
5. When the Add a New User window appears, enter the user information and click(touch)
104
USING THE PROGRAM
User Management
The following explains how to delete a registered user or edit user information.
Deleting User Information
You can delete a registered user's information as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Customer Setting.
3. In the user list, click(touch) the [Delete] button for the user information you want to delete.
ENGLISH
4. When the system password input window appears, enter the password and click(touch) [Confirm].
• The user information is deleted.
5. To complete user delete, click(touch) [Confirm].
USING THE PROGRAM
105
Editing User Information
You can edit a registered user's information as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Customer Setting.
3. In the user list, click(touch) the [Edit] button for the user information you want to edit.
ENGLISH
4. When the system password input window appears, enter the password, click(touch) [Confirm].
106
USING THE PROGRAM
5. When the Edit User window appears, enter the user information and click(touch) [Confirm].
• The updated user information is applied.
ENGLISH
6. To complete user edit, click(touch) [Confirm].
USING THE PROGRAM
107
Network Setting (AC Smart Premium Only)
The following explains how to configure the network environment.
ENGLISH
Item
Description
Select IP address allocation type.
IP address settings
IP address
Subnet mask
yy Get the IP address using DHCP: IP address is allocated by
the network automatically.
yy Using Static IP address: Get IP address from the network
administrator and type it manually.
Enter IP address
Enter the subnet mask information for the IP address.
Gateway
Enter IP address of gateway.
Main DNS
Enter the IP address of main DNS server.
Sub DNS
Enter the IP address of secondary DNS server.
108
USING THE PROGRAM
IP address settings
You can select the IP address allocation as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Network Setting.
3. In the detailed settings list, click(touch) IP address settings.
4. Click(Touch) an IP address allocation type you want.
• Get the IP address using DHCP: IP address is allocated by the network automatically
• Using Static IP address: Get IP address from the network administrator and enter it
manually
ENGLISH
IP address
You can enter the IP address as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Network Setting.
3. In the detailed settings list, click(touch) IP address.
4. When the IP information window appears, click(touch) the [Apply] button.
USING THE PROGRAM
109
Subnet mask
You can enter the subnet mask information for an IP address as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Network Setting.
3. In the detailed settings list, click(touch) Subnet mask.
4. When the IP Information window appears, enter the subnet mask information, click(touch)
[Apply].
ENGLISH
Gateway
You can enter the IP address of a gateway as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Network Setting.
3. In the detailed settings list, click(touch) Gateway.
4. When the IP Information window appears, enter the IP address of the gateway and click(touch)
[Apply].
110
USING THE PROGRAM
Main DNS
You can enter the IP address of a main DNS server as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Network Setting.
3. In the detailed settings list, click(touch) Main DNS.
4. When the DNS Server window appears, enter the IP address of the main DNS server and
click(touch) [Confirm].
ENGLISH
Sub DNS
You can enter the IP address of a secondary DNS server as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) Network Setting.
3. In the detailed settings list, click(touch) Sub DNS.
4. When the DNS Server window appears, enter the IP address of the secondary DNS server and
click(touch) [Confirm].
USING THE PROGRAM
111
E-Mail Setting (ACP, ACP Lonworks, AC Smart Premium Only)
When the administrator is not present, Central Controller emails any error information to the
administrator for reviewing. The following explains how to configure the email.
ENGLISH
Item
Description
E-mail account settings
Configuring user email account.
E-mail settings
Select whether to use the email.
Email Subject
Type an email subject line when sending an email.
Receiving e-mail
Register the email address of the receiver who will receive the
email.
The transmission cycle
during error occurs
(minutes)
Set the transmission cycle to send an email if an error occurs.
Automatic daily
error-notification mail
Configure an email to be sent at 00:00 every day, even if there
are no errors to report.
112
USING THE PROGRAM
E-mail account settings
You can configure the user's email account.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) E-Mail Setting.
3. In the detailed settings list, click(touch) E-mail account settings.
4. Type the email account information.
• User name: Enter the email user's name.
• Address e-mail: Enter the user's e-mail address.
• Outgoing mail server(SMTP): Enter the address of the mail server.
• Outgoing mail server port: Enter the port of the mail server.
• Server Access Account: Enter the server connection account.
ENGLISH
• Password: Enter the password to log onto the mail server.
5. Click(Touch) [Test account setting] to check if the configured account is correct.
6. When the Account Configuration Completion window appears, click(touch) [Confirm].
7. To complete the email account configuration, click(touch) the [Confirm] button.
USING THE PROGRAM
113
E-mail settings
You can select whether to use the email function as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) E-Mail Setting.
3. In the detailed settings list, click(touch) E-mail settings.
• If Enable is selected, the check box turns red and the Email Subject, Receiving e-mail,
The transmission cycle during error occurs (minutes), and Automatic daily
errornotification mail are enabled.
ENGLISH
Email Subject
You can type an email subject line as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) E-Mail Setting.
3. In the detailed settings list, click(touch) Email Subject.
4. When the Configuring Email window appears, enter the email title and click(touch) [Confirm].
114
USING THE PROGRAM
Receiving e-mail
You can register the email address of up to three email receivers as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) E-Mail Setting.
3. In the detailed settings list, click(touch) Receiving e-mail.
4. When the Configuring Email window appears, enter the email address of the email receiver and
click(touch) [Confirm].
ENGLISH
The transmission cycle during error occurs (minutes)
You can set the schedule for when to send an email (when an error occurs) from 10 minutes to within
one hour as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) E-Mail Setting.
3. In the detailed settings list, click(touch) The transmission cycle during error occurs (minutes).
4. When the Select an Email Schedule window appears, click(touch) a sending schedule you want.
USING THE PROGRAM
115
Automatic daily error-notification mail
You can configure an email to be sent automatically once per day, even if there are no error, as
follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) E-Mail Setting.
3. In the detailed settings list, click(touch) Automatic daily error-notification mail.
• Enable is selected, the check box turns red.
ENGLISH
116
USING THE PROGRAM
TMS Setting
The following explains how to configure the remote monitoring and control system.
ENGLISH
Item
TMS configuration
TMS server address
TMS server port
Update Cycle (seconds)
Site address
Description
Select whether to use a remote control service.
Configure the remote control service server address.
Configure the remote control service port.
Configures the remote control service update cycle
(in seconds).
Enter an address for the remote site.
Site name
Enter the site name.
Site code
Click(Touch) the [Request Site Code] button to enter the site
code.
Admin Name
Admin Contact
Enter the name of the site manager.
Enter the site manager's phone number.
USING THE PROGRAM
117
TMS configuration
You can select whether to use the remote control service as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) TMS configuration.
• If Enable is selected, the check box turns red and TMS server address, TMS server port,
Update Cycle (seconds), Site address, Site name, Site code, Admin Name, and Admin
Contact are enabled.
ENGLISH
118
USING THE PROGRAM
TMS server address
You can configure the server address of the remote control service as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) TMS server address.
4. When the Remote Service Information window appears, enter the service server address and
click(touch) [Confirm].
ENGLISH
TMS server port
You can configure the server port of the remote control service as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) TMS Server Port.
4. When the Remote Service Information window appears, enter the service server port and
click(touch) [Confirm].
USING THE PROGRAM
119
Update Cycle (seconds)
You can configure the update cycle of the remote control service information as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) Update Cycle (seconds).
4. When the Configuring Update Cycle window appears, click(touch) an update cycle you want.
ENGLISH
Site address
You can type the address of the site where Central Controller is installed.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) Site address.
4. When the Configuring Site Information window appears, enter the site address and click(touch)
[Confirm].
120
USING THE PROGRAM
Site name
You can type the name of the site where Central Controller is installed.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) Site name.
4. When the Configuring Site Information window appears, enter the site name and click(touch)
[Confirm].
ENGLISH
Site code
You can allocate a code for site management as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) Site code.
4. When the Configuring Site Information window appears, click(touch) the [Request a site code]
button to enter the site code and click(touch) [Confirm].
Notes
You must enter the site address details before you can request the site code.
USING THE PROGRAM
121
Admin Name
You can type the site manager's name as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) Admin Name.
4. When the Configuring Site Manager Information window appears, enter the site manager's name
and click(touch) [Confirm].
ENGLISH
Admin Contact
You can type the site manager's phone number as follows.
1. In the main menu, click(touch) the [Environment] menu icon.
2. In the Settings list, click(touch) TMS Setting.
3. In the detailed settings list, click(touch) Admin Contact.
4. When the Configuring Site Manager Information window appears, enter the site manager's phone
number and click(touch) [Confirm].
122
USING THE PROGRAM
Channel Settings (ACP, ACP Lonworks, AC Smart Premium Only)
The following explains channel setting of Central Controller.
ACP, ACP Lonworks
ENGLISH
Item
.
Description
CH5
Central Controller provides 1 RS-485 port for AHU unit
connection. (Up to 16 AHU units)
CH6
Central Controller provides 1 RS-485 port for Chiller unit
connection. (Up to 15 Chiller units)
USING THE PROGRAM
123
AC Smart Premium
ENGLISH
Item
CH1
Description
Central Controller provides 1 RS-485 port for AHU (Up to 16
AHU units) or Chiller (Up to 15 Chiller units) unit connection.
ver. 1.0.1
Download PDF

advertising