Cleaning and Maintenance Safety instructions for use Installation of drain hose To minimize the risk of fire within the inner bowl, the following should be observed: Warning: B efore cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock. about 100 cm Turn off the water tap Unscrew the water inlet hose 4 5 Pull out the water Clean the filter using Tighten up the inlet filter a hard bristle brush inlet hose 2 3 Open the lower Unplug the drain filter cover and pull hose plug Then out the drain hose. open the filter by turning to the left about 105 cm Hose Retainer Tie strap Cleaning the drain pump filter 1 about 105 cm 4 Remove any extraneous matter from the pump filter 5 After cleaning, refit the Close the lower drain filter cap and tighten it cover by turning it clockwise. and insert the drain plug max. 100 cm 3 about 145 cm 60 - 100 cm 2 min. 60 cm 1 max. 100 cm about 145 cm about 100 cm min. 60 cm Cleaning the water inlet filter • The drain hose should not be placed higher than 100 cm above the floor. • Proper securing of the drain hose will protect the floor from damage due to any water leakage. • If the drain hose is too long do not force back into the washing machine. This will cause abnormal noise and cause the machine to malfunction and leak. 1 2 Pull out the dispenser drawer 3 Clean the dispenser drawer under flowing water Cleaning in general Clean inside the recess with an old toothbrush 4 Insert the dispenser drawer Important: Do not use methylated spirits, solvents or similar products. Exterior Proper care of your washing machine can extend its service life. The outside of the machine can be cleaned with warm water and a neutral non-abrasive household detergent. Immediately wipe off any spillage. Wipe with damp cloth. Avoid striking the surface with sharp objects. Never hose down the machine! Interior Dry around the washing machine door opening, flexible gasket and door glass. Run washing machine through a complete cycle using hot water. Repeat process if necessary. BS Plug Safety Details (For U.K. User) This appliance must be earthed As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The green and yellow wire must be connected to the terminal in the plug marked E or by the earth symbol or coloured green or green and yellow. The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse. Green and Yellow (Earth) ) Brown(Live) Blue(Neutral) Level adjustment Cleaning the dispenser drawer 5 Once you have finished cleaning, replace the drawer and run a rinse cycle without laundry or soap. • Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in a tumble dryer. Oil-affected items can ignite spontaneously, especially when exposed to heat sources Such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard. If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature of the items. They should not be removed from the tumble dryer or piled or stacked while hot. • Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances should not be placed in a tumble dryer. Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and wax removers. • Items containing foam rubber (also known as latex foam) or similarly testured rubber like materials should not be dried in a tumble dryer on a heat setting. Foam rubber materials can, when heated, produce fire by spontaneous combustion. • Fabric softeners or similar products should not be used during a drying cycle, to eliminate the effects of static electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or product. • Undergarments that contain metal reinforcements should not be placed in a tumble dryer. Damage to the tumble dryer can result if metal reinforcements come loose during drying. When available a drying rack could be used for such items. • Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer. • Rubber-backed articles, clothes fitted with foam rubber pads, pillows, rubber boots and rubber-coated tennis shoes should not be placed in a tumble dryer. • Proper level-adjustment of the washing machine prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. • If the floor is uneven, adjust feet as required. (Do not insert pieces of wood etc. under the feet). Make sure that all four feet are stable and resting on the floor. Then check that the appliance is perfectly level. (Use a spirit level). Wooden floors (Suspended floors) • Wooden floors are particularly susceptible to vibration. • To prevent vibration we recommend you place rubber cups under each foot, at least 15mm thick under the washer, secured to at least 2 floor beams with screws. Rubber Cup • If possible install the washer in one of the corners of the room, where the floor is more stable. Insert the rubber cups to reduce vibration. You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept. E L N Fuse Cord grip Electrical connection 1. Do not use an extension cord or double adapter. 2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person to prevent danger. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible. • Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre. • Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst under pressure. The electronic control unit may become unreliable at temperatures below freezing point. • If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine standing at room temperature for a few hours before putting it into operation. Caution • The hose supplied with the machine must be used. Old hoses may not be reused. • The appliance is not intended for use by young children or infirm persons without supervision. • Young Children should be supervised to ensure that they do not play with appliance. Safety instuctions for the installation Safety instructions for use Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation. • Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease. • This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product. • Never modify the appliance on your own, as this is dangerous. • This appliance is heavy. Transporting with care. • Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result. • All installation work must be carried out by a qualified fitter or technician. • Have electrical connections done by a qualified electrician. • Never place the appliance on the power cord. • If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance. • Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect by pulling the power cord. Never touch the plug with wet fingers or hands. • Do not overload the appliance. • Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label. • Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp. • Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire. • Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter. • Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage. Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service. • Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion. • Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes. • Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflammable gas. Such materials may cause fire or explosion. Never use combustible detergents. • Only add the prescribed amount of softener. Excessive amounts may damage the clothes. • After washing, keep the drum door open to protect the door seal. • Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding. • Animals and children may get into the washing machine. So always check the appliance before using it. • During washing, the glass door becomes very hot. Keep children away from the appliance when in operation. • Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine. • The product should be serviced and repaired only by the authorised customer service using original replacement parts. • When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children. • When placing on a carpeted floor, make sure that the opening in the socket is not blocked. • If the appliance has been under water then contact the customer service. There is danger of electric shock and fire. • The cover cup of the filter as well as the dispenser drawer may not be opened during the operation. • Keep all washing powder and detergents away from children. Danger of poisoning Disposal • When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by European Directive 2002/96/EC. • All electrical and electronic products should be disposed of separately from municipal waste stream via designated collection facilities appointed by the government or the local authorities. • The correct disposal of your old appliance will help prevent potential adverse consequences for the environment and human health. • For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. Install or store the appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit the power plug to a grounded wall socket that complies with all statutory regulations and ordinances. Ensure that the base opening is free from obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee. N Troubleshooting CAUTION about positioning the appliance Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is not impeded by carpets, rug etc. • Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine. • If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel (85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances. • The washing machine must not be installed in rooms where the temperature may drop below 0°C. • Please ensure that when the washing machine is installed , that a Service Technician can gain easy access in the event of a breakdown. • Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between the top of the washing machine and underside of the worktop. • Water supply is not adequate in area • Water supply taps are not completely open. • Water inlet hose(s) are kinked. • The filter of the inlet hose(s) are clogged. Check another tap in the house. Fully open tap. • Drain hose is kinked or clogged. • The drain filter is clogged. Clean and straighten the drain hose. Clean the drain filter. For more detailed information, please refer to “Cleaning the drain pump filter” • L oad is too small. • L oad is out of balance. • The appliance has an unbalance detection and correction system. If individual heavy articles are loaded (ex. bath mat, both robe, etc.), this system may stop spinning or even interrupt the spin cycle altogether. • If the laundry is still too wet at the end of the cycle, add smaller articles of laundry to balance the load and repeat the spin cycle. Floor is unstable. Feet are not adjusted CAUTION about the power cord We recommend connecting most appliances to a dedicated circuit which is protected by a mains fuse. That is, a single outlet supplying power only to the appliance concerned, without any additional outlets or branch circuits. Check the specifications of this owner‘s manual. Do not overload wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. • Is the door opened or not completely closed? • Water overfills due to the faulty water valve. CAUTION about the floor surface • The installation surface must be clean, dry and level. • Install washing machine on a flat hard floor. Poorly constructed timber base floors can contribute to excessive noise and vibration. • Proper placement and levelling of the washing machine ensure long, regular and reliable operation. • The washing machine must be perfectly level and firmly in position. • It must not “see-saw” across corners under load. • The installation surface must be clean, free from floor wax and other lubricant coatings. • Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur. • The washer experienced a power failure. Technical Specification Name of product Front loading washing machine Max. Watt 2100 W (Wash) / 1500 W (Dry) Power supply 220-240 V~, 50 Hz Capacity 9 kg (Wash) / 6 kg (Dry) Size WxDxH mm: 600 x 640 x 850 Water consumption 95 Weight 72 kg Permissible water pressure 100-1000 kPa (1.0-10 bar) Add 1 or 2 similar items to help balance the load. Rearrange load to allow proper spinning Owner‘s Manual F1403RD(1~9) F1403RDW WD-CD914W The floor should be a solid surface. Adjust the feet so that the machine does not rock from side to side or front to back. Close the door completely. If the " " does not clear, call for service. Unplug the power plug and call for service. CAUTION about location and moving This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain (gully) in the immediate vicinity. If relocating the appliance use the original packing material. Packaging material (e.g. plastic film, Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children and do not allow children to play inside the bowl as they may become trapped. @ Straighten hose(s). Check the filter of the inlet hose(s). • Water level sensor has malfunctioned. Close the water tap. Unplug the power plug. Call for service. • Over load in motor. • Check water supply. Rattling and clanking noise Thumping sound Vibrating noise Water leaks. Excessive suds Washing machine does not start Washing machine won’t spin Door does not open Restart the cycle. Turn the tap on. If “ ” is not released, unplug power plug and call for service. Extraneous objects such as coins or safety pins maybe in drum or pump. Heavy wash loads may produce a thumping sound. This is usually normal. Have all transit bolts and packing been removed? Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary. Too much detergent or unsuitable detergent. Power cord may not be plugged in or connection may be loose. Check that the door is shut. Check that foreign objects may be blocking the drain causing the water not to drain out. Once started, the door can not be opened for safety reasons. At the end of the cycle or when Start Pause is pressed, wait one or two minutes before opening the door to allow the electric locking mechanism time to release. Before use please read carefully the safety instructions! Thank you for buying an LG fully automatic washing machine. Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance. Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine. For the U.K. customer CUSTOMER SERVICES Tel. : +44-(0) 844 847 LGLG(5454) Fax. : +44-(0) 844 847 1413 LGEUK SERVICE WEB-SITE : http://www.lge.co.uk P/No. :MFL59755568 Additional programs Preparation Washing symbols Washing temperature CHECKING THE MACHINE Never use a defective machine! In case of any failure, first unplug the machine and turn off the water tap. WATER CONNECTION Turn on the water tap INSERT PLUG INTO THE MAINS SOCKET Never touch the plug with wet hands! Never remove the plug from the socket by pulling on the cord. DOING LAUNDRY AND USING MACHINE WITH CARE - empty all pockets - remove all metal parts - place the delicate textiles into the laundry net - close zippers LAUNDRY WITH DIFFERENT AMOUNTS OF SOILING - wash new textiles separately lightly - do not prewash - pretreat dirty spots heavily - pre wash Hot ironing Hang to dry Do not bleach Luke warm ironing Do not iron Drip dry Handy to bleach Pre Wash The Pre wash compartment can be used for Normal to heavy soiled clothes, by adding a prewash or normal detergent to this compartment before selecting this wash option with the Cycle. B Main Wash For Laundry requiring detergent, place recommended dosage in to this compartment. Please note that liquid detergent will enter the tub as it is poured and may not be suitable for a delay start. C Softener Do not exceed the MAX-Level. Highly densed softeners are to be diluted with some water. Excessive softener can cause brown or grey spotting on the clothes. Washing program table Program Cotton Cotton Quick Synthetic Baby Care Wash+Dry (6kg/6kg) Quick 30 Delicate Hand Wash / Wool Colored laundry which is lightly soiled fast Delicate laundry easily damaged 40°C (Cold, 30°C) - Time Delay - Intensive - Rinse+ - Rinse+Spin - Normal+Hold Maximum Load Control panel Dispenser drawer Fill detergent Refer to the written information on the detergent's packaging Using the Tablets 2) L oad the laundry 1) O pen the door and into the drum. Tablets into the drum. Power button Program Cycle Start / Pause Options Temperature Spin C 3 B A Turn off tap - Close water supply - Clean the machine - Unplug machine Drum Rating - Low Temp. - Iron Dry - Cupboard Dry - Eco Dry - Time Less than 4.5 kg Favorite Note: T he last 6 minutes of dryinng time, A sensor(Thermistor) detects clothes drying conditions. When the dryness is low, cycle time will be added by max. 30 mins with “6” mins remaining window display. - Favorite program allows you to store a customized wash cycle for future use. - To make a Favorite program: (1) Select a cycle. (2) S elect The course, washing method, number of rinses, spin speed, water temperature etc. (3) Press and hold Favorite program button 3 econds (2 beep sounds). The Favorite program is now stored for future use. To reuse the program, select Favorite program and press Start/Pause. Intensive If the laundry is heavily soiled “Intensive”option is effective. Less than 7 kg Turn the machine ON by pressing the Power button Additional Steps - Turn the machine off - Leave door open to allow drum to dry Filter cover. Less than 6 kg Remove laundry - Open the door - Remove the laundry Less than 2 kg – n Notes Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care. Warning: Keep all washing powder and detergents away from children. Danger of poisoning hi The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0806. is Press Start / Pause to start or pause the washing process Select Spinning speed and Washing temperature 4 additional programs Time Delay / Favorite / Intensive / Medic Rinse fin i shed Select the Dry mode Woolen Articles Medic Rinse - S ome woven and loopknit materials may shrinks, by varying amounts, depending on their quality. - Always stretch them out immediately after drying. Woven and Loopknit Materials This allows the final rinse to be heated to 40 degrees. Available in the Cotton, Cotton Quick, Synthetic, Baby Care and Wash+Dry (6kg/6kg) programs. Medic Rinse is set by default in the Baby Care program. The respective temperature indicator will light up. Dry g • Drying course can last up to 150min. When selecting drying only, drying course will start after spining. • These drying times are given as a guide to help you set your dryer for manual drying. Drying times can vary greatly depending on dampness, room temperature and type of fabric and your own experience will be your best guide. Cold water tap must be left on during drying cycles. • This washer-dryer’s automatical process from washing to drying can be selected easily. • For most even drying, make sure all articles in the clothes load are similar in material and thickness. • Do not overload dryer by stuffing too many articles into drum. Items must be able to tumble freely • If you open door and remove load before dryer has finished its cycle, remember to press the Start/Pause button. • By turning the DRY dial, you can select : Cupboard Dry Eco Dry 30 60 120 Low Temp. Iron Dry • After the end of dry, “ ” is displayed. By pressing the “Start/Pause” button the program can be ended. If you not press the “Start/Pause” button, the program is ended after about 4 hours. “ ” Cooling Cycle. Permanent Press and Synthetics - Do not overload your dryer - Take out permanent press articles as soon as the dryer stops to reduce wrinkles. Baby clothes and Night Gowns - Always check the manufacture’s instructions. Select this function to lock the buttons on the control panel and to prevent tampering. 6 3 sec. 6 3 sec. 1 Fiber glass - D o not dry fiberglass articles in your dryer. Glass particles left in the dryer could be picked up by your clothes the next time you use the dryer and irri tate your skin. Fiber or Leather Materials - Always check the manufacture’s instructions. 3.Completion of Drying • When drying cycle is completed, “ ” [Cool Down] is displayed on the Multi display. • The Cool Down is setting automatically when a drying cycle is complete. • When you are not remove a loaf of clothes from the dryer as soon as it stops, wrinkles can form. • The Cool Down operating periodically tumbles, rearranges and fluffs the load to tumbles, rearranges and fluffs the load to hours. • The “ ” message will continue to display until the clothes are removed or the Start/Pause button is pressed. 6 3 sec. To deactivate: Press and hold Press press and hold the Option buttons Start/ the Option buttons simultaneously Pause simultaneously for 3 seconds until the " " is removed from the display. Select the desired program Press Start/Pause TUB CLEAN is special cycle to clean the inside of the washing machine. A higher water level is used in this cyle at higher spin speed. Perform this cycle regularly. 6 3 sec. 1 Empty the drum completly and close the door Rubber and Plastics - D o not dry any items mode from or containing rubber or plastics, such as: a) aprons, bibs, chair covers b) curtains and table cloths c) bathmats Change to the desired program, whilst in child lock mode: 2 To activate: press and hold the Option buttons simultaneously until " " appears in the display. Tub Clean • By turning the DRY dial, the drying time can be selected. - D o not tumble dry woolen articles. Pull them to their original shape and dry them flat. as Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufacture’s care label or instructions when washing. Intensive: If the laundry is heavily soiled “Intensive” option is effective. Set program at “Wash : Cotton 60°C + Intensive” and “Dry : Eco Dry (First drying cycle load : 6kg, Second drying cycle load : 3kg)” for test in accordance with EN50229 and IEC50229. Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic, Baby Care and Wash+Dry (6kg/6kg) programs. Rinse + : Used to introduce an additional rinse, which may assist in removing traces of detergent residue. Medic Rinse: For best results or for cleaner rinsing, you can choose this heated Rinse option. Medic Rinse is automatically selected on Baby Care program. Select an Option Pre Wash / Rinse+Spin / Rinse + / Normal+Hold w 1 single size 2.Drying time guide - B y selecting the Intensive option, the washing duration may be extended, depending on the program selected. - To use this option, press the intensive button once before the wash program is started. For best results or for cleaner rinsing, select the “Medic Rinse” option. Select a Program il “Hand wash” marked delicate and wool laundry Cotton bedding with filling duvet, pillow, blanket, sofa cover with light filling 30°C (Cold, 40°C) Dry (Option) 2 Child Lock • U se your Automatic Cycles to dry most loads. Electronic sensors measures the temperature of the exhaust to increase or decrease drying temperatures for faster reaction time and tighter temperature control. - Press Power button. - Turn the Program dial to select the program you require. - Press Time Delay button and set the finishing time. The machine will then automatically work out the turn on time based on the chosen cycle. - Press the Start/Pause button. How to set “Time Delay” Loading the Drum Check the folds of the flexible gasket (grey) and remove any small articles or foreign objects that may have fallen from items in the previous wash . Check all garments for loose items before loading and ensure that clothes are clear of the door gasket before closing the door so that the clothes or door gasket are not damaged during the wash. 1. Drying Automatic guide • Recommend Automatic drying course as a kind of clothes. a) Low Temp. : For Synthetics select b) Iron Dry : If you want to iron clothes d) Eco Dry : A special cycle to reduce water usage during c) Cupboard Dry : For Cottons select the dry cycle. e) Time (30/60/120 minutes) - 30 min. : Cotton 1.5 kg - 60 min. : Cotton 3 kg Note: T he estimated drying time varies from the actual drying time with an Automatic. - 120 min. : Towel 4.5 kg The type of fabric, size of the load, and the dryness selected affect drying time. Allows you to set the cycle's ending time (by hourly increments) in advance. nt Duvet Water Temp. Fabric Type Option (Option) Color fast garments (shirts, 60°C nightdresses, pajamas...)and lightly (Cold, 30°C, - Time Delay soiled white cotton (underwear) 40°C, 95°C) - Intensive Lightly soiled clothing and - Medic Rinse 40°C small loads (Cold, 30°C, - Pre Wash - Rinse+ 60°C) Polyamide, Acrylic, Polyester - Rinse+Spin - Normal+Hold 60°C Lightly soiled baby wear (40°C, 95°C) - Time Delay - Intensive 60°C A small amount of laundry (Cold, 30°C, - Medic Rinse which can be dried. 40°C, 95°C) - Pre Wash - Rinse+ Time Delay tu ECOLOGICAL WASHING - make use of the max. washing quantity - do not “pre wash” if possible - use short program if possible Do not wash Additional programs ai DRUM CARE - remove extraneous objects - leave door open to dry the drum - check the rubber seals regularly Dry flat Drying cycle 1 W WATER TREATMENT - with hardness III water - use water softening agent Do not tumble dry Dispenser drawer A HANG UP WASTE WATER HOSE Hose elbow connection e.g. attach to water tap Medium hot ironing Sort the laundry note washing instruction symbols Degree of soiling Type of textile / colour - Display 2 3 Add anti-limescale (Calgon) to the main wash compartment. Close the disp. drawer 5 4 Power ON with Then press and hold Spin and Temp. button Press the Start/Pause button to start Tub Clean process After the cycle is complete, leave the door open to dry Beep on / off The Beep on/off function can be set only during the washing cycle. To set the Beep On/Off function follow the below steps. 1.Turn on the washing machine (by pressing the Power button). 2.Press the Start/Pause button. 3.Press and hold the Option and Spin button simultaneously for three seconds to set Beep on/off function. Once the Beep on/off function is set, the setting is memorized even after Power is off.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project