LG | WF-S1250 | LG WF-S1250 Owner’s Manual

Washing
Machine
OWNER'S MANUAL
MODEL
:
WFT10(1)C60(1)D(E,F)C(H,P,D,E,F,M)
WFT15C61EF
WF-T1111D
WF-S1250
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model
name
and serial number of the set.
Quote this information to your dealer when you
require
service.
P roduct Features
Washer doesn't
rinse
or
operate while the lid is open. If the lid is open during the wash,
the operation stops for safety.
spin cycles,
sensors
The
automatically
sensor
detects the
temperature and the quality of
washing
and
FUZZY
which
rinsing,
Detergent put by a user and
washing algorithm for
give the best washing effect.
quantity
of
a
the
water to make the best
can
logic control
A built-in load
automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal WATER LEVEL
and washing time.
sensor
SENSING
START
SETTING
Laundry Sensor
WASHING
Optimum
Washing
Water Level Sensor
Condition
Advanced
ensures
AUTO
POWER
OFF
technology is built into the
washing result.
Electronic Control
System
which
the best
Turbo drum
When "Punch
washing (option)
washing wings turn, the washing
opposite direction. This makes the both
sides current of water which improve washperformance by rubbing clothes strongly.
+
3"
tub turns in the
Applied
3
models : WFT
Step washing
3
step washing makes the best washing performance with low tangling.
Rubbing and
Shaking
Rubbing
Auto Restart
In the event of
automatically
NOTE
:
Be
Shaking and
Disentangling
(option)
power failure, the washing machine will
start its interrupted cycle when power is resumed.
a
sure
to
remove
the unit from the carton base, otherwise the
machine will not be able to
operate properly.
C
ontents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
properly.
in the
Troubleshooting section. If you review
may not need to call for service at all.
Introduction
Before
Starting
Safety
to Wash
Troubleshooting Tips first,
Information
you
4
Identification of Parts
7
Function Information
8
Preparation
Before
Use of Water,
Detergent,
Special
Washing Programs
chart of
our
9
Washing
Bleach and Softener
Guide for Stain Removal
10
13
Function of each Button
14
FUZZY Wash
16
(Normal Wash)
ECONOMY Wash
16
JEAN Wash
16
WOOL Wash
16
DELICATE
16
SOAK Wash
18
FAVORITE Wash
19
SILENT
20
Additional Function
TUB CLEAN
21
Program
Option Washing
22
DELAY START
(RESERVATION)
Wash
Other Useful Functions
Installation
Placing
and
Connecting
Connecting
Care and Maintenance
Troubleshooting
Terms of
Warranty
Specification
Grounding
25
26
Leveling
Water
Supply
24
Hose
Drain Hose
Method
27
30
31
Cleaning
and Maintenance
32
Common
washing problems
34
Troubleshooting
35
Terms of
36
Warranty
Specification
37
4
S afety
Read
carefully
that will
Introducin
Information
and
thoroughly through this booklet as it contains important safety information
user from unexpected dangers and prevent potential damages to the product.
protect the
This booklet is divided into 2 parts
:
This is
be
:
:
Warning
warning sign specifying
dangerous.
This is
a
a
sign specifying 'Strictly
Warning
:
Failure to
sign
Caution
:
comply
may result in
and Caution.
user's
Forbidden'
might
applications.
major physical injuries
comply
sign may
damages
result in minor
WATER
which
with the instructions under this
Failure to
to the
applications
or
death.
with the instructions under this
physical injuries
or
product.
Warning
HEATER
SAFETY
?
Under certain conditions
hydrogen gas may be produced in a water heater that has not been
Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
used for two weeks
PROPER
or more.
Caution
INSTALLATION
?
?
The base
opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or
deformation may
?
occur.
Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
?
If not
grounded properly, break down and leakage of electricity may
cause
electric shock.
Must be
positioned so that the plug is accessible.
plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.
Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
If the
?
occur, which may
5
S afety
Information
YOUR
Warning
LAUNDRY
AREA
?
Keep
the
underneath and around your
area
materials such
lint, paper,
as
Operating with such
explosion or fire.
?
rags,
appliances
chemical,
free of combustible
etc.
materials around the machine may
trigger
Close
supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.
There is
that children
potential danger
Do not touch the power
It will
cause
Do not
put
plug
with
a
might
drown in the tub.
wet hand.
electric shock
hand, foot
your
or
anything under
operation.
the
washing
machine
while the
washing
There is
rotating mechanism under the machine, so you could
WHEN USING
a
machine is in
be
injured.
Caution
THE WASHER
?
Use this
?
The
?
appliance only for its intended purpose as described in this Owner's Manual.
laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer's wash and care instructions.
To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.
NOTE
Pressing
:
Power button to turn off does NOT
disconnect the
?
Make
sure
that
appliance
from the power
supply.
drainage is working properly.
If water is not drained
may induce
?
properly, your floor may get flooded. Flooded floors
electricity leakage, further resulting in electric shock or fire.
If, during spinning, opening the lid does not stop the
immediately discontinue operating the machine.
Call for
repair.
A machine that
spins
tub within about 15
with its door open may
seconds,
cause
injuries.
Never reach into washer while it is
Wait until the machine has
Even slow rotation
Never
moving.
completely stopped before opening the lid.
can cause
injury.
attempt operate
appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating
Do not
this
to
use
with
a
damaged plug may cause
electric shock.
water hotter than 50°C.
Use of excessively hot water may
leakage of water.
cause
damage to fabrics
or cause
Introducin
6
S afety
Introducin
Information
WHEN USING
Warning
THE WASHER
Do not
use a
plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire break down, and/or
deformation of parts.
,
Do not mix chlorine bleach with ammonia
Mixing
different chemicals
Do not wash
can
or
acids such
produce
as
vinegar and/or rust remover.
toxic gases which may
cause
death.
dry articles that have been cleaned in, washed in, soaked in, or spotted
or
explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
or
with combustible
It may
WHEN NOT
ignite
or
explode.
Caution
IN USE
?
Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
a break or
rupture should occur. Check the condition of the fill hoses; they may need
if
replacement after 5years.
?
?
When the air
temperature is high and the
occur
and thus wet the floor.
Wipe
off dirt
or
dust
Using unclean
?
on
water
temperature is low, condensation may
the contacts of the power
power
plug
may
cause
plug.
fire.
Before discarding a washer, or removing it from service,
prevent children from hiding inside.
Children may be
Do not
remove
the washer lid to
and suffocated if the lid is left intact.
trapped
attempt to repair
or
replace
recommended in this Owner's
any
Manual,
part of this appliance unless specifically
or
in
published user-repair instructions
that you understand and have the skills to carry out.
Operating
the machine with
cause
for fire
Do not
tamper with controls.
or
improperly replaced parts
may be
a
electric shock.
It may lead to electric
shock, fire , break down, deformation.
Do not
yank the power cord in an attempt to disconnect the
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may
due to short-circuit
cause
power
plug.
electric shock
or
fire
.
When you
part of the
It will
are cleaning the washing machine,
washing machine.
cause
do not
short circuit and electric shock.
apply water directly to any
7
I dentification of Parts
Body
POWDER DETERGENT
AND SOFTENER BOX
WATER SUPPLY
HOSE
Make
sure
the
water does not
leak.
POWER PLUG
If the
supply cord is
damaged, it must be
replaced by the
BLEACH
DISPENSER
manufacturer
or
service agents
its
or
similarly qualified
FUNCTION SELECTOR
person in order to
avoid
a
hazard.
TUB
LINT FILTER
Clean
START/PAUSE
BUTTON
Use to start
regularly
stop linting
on
to
the
clothes load.
or
stop the washing
machine
DRAIN HOSE
for pump model
temporarily.
Check if the drain
hose is
hung up
operating the
washing machine.
before
DRAIN HOSE
ADJUSTABLE LEGS
Use to level the
for
washing
non
model
machine for correct
balance &
spin
operation.
BASE
Accessories
Water
supply
hoses
Drain hose
or
or
1 Each for COLD and
HOT water
NOTE
Part
can
be different
according to
the model.
pump
Introducin
8
F unction Information
Our machine
provides
various
washing
methods which suits various conditions and
types of laundry.
Different types of
laundry washing
FUZZY(Normal)
Use this
Program
Wash
for
everyday washing
e.g.
sheets, towels, T-shirts. (refer to page 16)
JEAN Wash
Use this
Program for heavily soiled durable garments e.g. overalls, jeans.
or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)
Thick and heavy clothes
DELICATE Wash
Use this program to wash DELICATE and washable laundries.
(refer to page 16)
WOOL Wash
Delicate clothes
(lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
Before washing your woolens check the care label for the washing instructions.
When washing woolens use a mild Detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump
?
?
?
?
(Ensure that the whole article is suitable for machine washing and not just the backing
You may wish to handwash these articles and place them in the machine to spin dry.
blockages.
material.)
FAVORITE Wash
This
setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 19)
SILENT Wash
Use this program to wash
quietly at night. (refer to page 20)
to the condition of
Washing according
laundry
ECONOMY Wash
ECONOMY wash
can
be selected to wash
lightly
soiled clothes of less than 2.0
kg in a short time. (refer to page 16)
SOAK Wash
SOAK Wash
dirt and
Other
can
be selected to wash
heavily
soiled
laundry by soaking
in water for
some
time to
remove
grime. (refer to page 18)
washing
method
TUB CLEAN
Use this program to clean the inside of washing machine
especially Inner tub & Outer tub (refer to page 21)
.
DELAY START Wash
DELAY START Wash is used to
The number of hours to be
delay the finishing time of the operation.
delayed can be set by the user accordingly. (refer to page 24)
OPTION WASH
When the
user
needs
only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN,
(refer to page 22)
SOAK/WASH/RINSE/SPIN.
9
P reparation Before Washing
BeforStaingWsh
Care Labels
*
Look for
a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Sort clothes into loads that
can
be washed with the
same
wash
cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
?
SOIL
?
COLOR
?
(Heavy, Normal, Light)
Separate clothes according to the type and amount of soil.
(Whites, Lights, Darks) Separate white fabrics from colored fabrics.
LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
Lint Producers
Terry cloth, Chenille, Towels, Nappies, Diapers
Synthetics, Corduroy, Permanent Press, Socks
Lint Collectors
Check before
?
?
?
?
?
?
?
pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
Pretreat any dirt and stains.
Make sure the clothes are washable in water.
washing instructions.
Remove tissue in pockets.
on
stains or
heavy
Pretreat shirt collars and cuffs with
Before
?
WIRE
Check the
Pretreatment
?
Loading
Check all
Use
a
washing treat special
a
soil
pre-wash product or liquid Detergent when placing them in the washer.
liquid Detergent or a paste of water and granular Detergent.
stains with bar soaps,
pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The
longer they are
left the harder
they are to remove.
(For more detail refer to page13)
Loading
Do not wash fabrics
WARNING
containing flammable materials (waxes, cleaning fluids, etc.).
Fire Hazard
Load Size
The WATER LEVEL should just
cover
the clothes.
Adjust the load
size
Never place items in the washer that are
dampened with gasoline or other flammable
accordingly. Loosely load clothes no higher than the top row of holes in the
fluids.
washer tub. To add items after washer has
No washer
submerge additional items.
Light
and
started, press Start button and
Close the lid and press Start button
Large-sized clothing
Clothes like downs and woollens
again to restart.
can
completely remove oil.
Do not dry anything that has
of oil on it (including cooking
Doing
so can
result in
ever
had any type
oils).
death, explosion,
light weight, large and float easily. Use a nylon net and
laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
wash them in
a
are
small amount of water. If the
Long laundry items
nylon nets for long, DELICATE items. For laundry with long strings or long length a net will prevent
tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
Use
,
or
fire.
10
U
BeforStaingWsh
Using
of Water,
se
Detergent, Bleach and Softener
Water
Amount of WATER LEVEL
?
?
?
?
?
This machine detects the
quantity
of
laundry automatically,
then sets the
WATER LEVEL and proper amount of Detergent.
When you select a wash program, the WATER LEVEL and amount of
Detergent (to be used) will be shown on the control panel.
The following table shows the amount of water.
When the WATER LEVEL is automatically detected, it may differ depending
on the
quantity of laundry even though the same WATER LEVEL is indicated
on the control
panel.
The amount of a cup in the diagram is about 40g for concentrated Detergent.
NOTE
[ Minimum water amount ]
It
depends on laundry load and washer model. Or manually you can pour a certain amount water into tub
directly to some height. That's because if water level reaches to the some height sensed by washer itself, washer
automatically operates. In other words, it is needed to pour water to the point when washer starts operating.
Water
Temperature
?
The machine sets the
?
You
?
can
appropriate temperature automatically according to the wash program
change the Water Temperature by pressing the WATER TEMP. button. (refer to page 14)
.
The
temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.
temperatures of:
HOT 49~60°C...(120-140˚F)
White items, diapers, underclothing and heavily soiled, colorfast items.
We recommend
-
-
-
?
WARM
COLD*
29~40°C...(85-105˚F)
18~24°C...(65-75˚F)
Most items
Only very bright colors
with
-
-
washing in COLD water additional steps may be needed:
Adjust Detergent amount and pre-dissolve Detergent in WARM
light soil.
When
Pretreat
water
spots and stains
heavily soiled items
appropriate bleach
*
Temperature below 18°C...(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29°C...(80-85˚F).
If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.
-
-
Soak
Use
NOTE
If iron is
spots
or
present in the water the clothes may become an all-over yellow or they may be stained with brown or orange
always visible. Installation of water softener or an iron filter may be necessary for severe cases.
streaks. Iron is not
Using Detergent
Detergent
Follow the
Use
more
Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing
the
right Detergent
We recommend the
use of domestic Detergent,
(powder, liquid or concentrated). Soap
powders should not be used in your washing machine. When washing
remember to use Detergent suitable for washing woolens.
granulated
soap
flakes or
woolens
11
Using Detergent
How much
Detergent
When you select a wash program the WATER LEVEL and the amount of Detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated Detergent.
The correct amount of
Detergent will vary depending on the amount of soil in your clothes (Jeans and work
cloches may need more Detergent, while bath towels usually need less.).
For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.
Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of
foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough
Detergent has been used; soil and lint can settle back on the clothes or the washing machine.
If excess
Detergent is used, the rinse will not be
pollution, so use it accordingly.
as
clean and efficient.
Also,
it could
cause
environmental
Adding
the
Detergent
Powder Detergent / Fabric Softener dispenser.
Open the Detergent dispenser and deposit the appropriate
amount of Detergent
Where you
where you deposit the Detergent
deposit the
Powder Detergent dispenser.
detergent
Some Detergents MUST be fully dissolved before
adding to your machine to get the best wash results.
Check the instructions on the Detergent packet.
If you use powdered Detergent it is essential that the required amount be fully dissolved in very HOT water
before being added to WARM or HOT water for the actual wash.
Pre-dissolving Detergent in WARM water when washing in COLD water can improve its performance.
Using Liquid
?
?
Bleach
Check
clothing care label for special
laundry to be bleached
Dilute liquid chlorine bleach.
instructions and
separate the
?
Measure the recommended amount of
following instructions on the bottle.
liquid bleach carefully
?
Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
NOTE
Never pour undiluted liquid bleach directly onto clothes
This may cause change of color or damage the laundry.
Do not pour
powdered bleach into bleach dispenser.
or
into the wash basket.
Bleach
dispenser
BeforStaingWsh
12
U
BeforStaingWsh
Using
se
of Water,
Detergent, Bleach and Softener
Fabric Softener
Available Fabric Softener
?
Do not
?
For
more
Depositing
Don't
?
Type
concentrated fabric softener. This may cause some problems in automatic
details refer to the softener products instructions for use.
use
use
Fabric Softener
softener with
detergent.
Powder
Use softener in last rinse water
When
dilute softener
using dispenser,
(30ml)
When filling dispenser, do
?
Detergent /
Fabric Softener
not
splash or
overfill. It may stain clothes.
Never pour fabric softener directly
?
on
Limit Line
clothes.
Depositing
It may stain them
If spotting occurs, wet and rub with hand
?
dispenser.
Where you deposit
the softener
(30ml)
with fresh water
?
dispensing.
dishwashing liquid (or mild bar soap)
If the
and
filled,
is
softener
it can overflow.
over
Fabric
Softener
softener
don't fill it
above the
limit line.
Cap
rewash.
NOTE
Fabric Softener will be inserted
When water pressure is
Scrud(Waxy
Build
automatically during
low, the softener may have
the final rinse and the machine
to be inserted
gives
on
alarm sound.
manually.
up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
comes into contact with Detergent. This
build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it
smell in your washer.
If you wish to
?
Using
?
When
?
?
?
?
use
fabric softener
we
can
result in stains
on
your clothes
or an
unpleasant
recommend
fabric softener
sparingly.
filling the dispenser, do not splash or overfill.
Clean dispenser as soon as the cycle is finished.
Clean your machine regularly. (refer to page 21 or 32)
Cold water washing increases the chance of this build-up
HOT wash e.g. every 5th wash should be at least a warm
Fabric softener of thinner
build-up.
consistency
is less
likely
occurring.
We recommend
a
regular WARM or
one.
to leave residue
on
the
dispenser and contribute to a
13
Guide for Stain Removal
S pecial
WARNING
Do not
mix
chlorine bleach with other household chemicals such
liquid
products containing ammonia.
use or
These mixtures
as
toilet cleaners, rust removers, acid
or
produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
Read and comply with all instructions on stain removal products.
Keep stain removal products in their original labeled containers and out of children's reach.
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents
or other flammable or
explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
can
?
?
?
?
?
?
For successful stain removal:
?
Remove stains
?
Determine the kind of
promptly.
stain, then follow the recommended
treatment in the stain
removal chart below.
?
To
pretreat stains,
use a
granular Detergent and
prewash product, liquid Detergent,
?
Use COLD water
?
Check
?
Check for colorfastness
?
Rinse and wash items after stain removal.
care
on
or a
paste made from
water.
unknown stains because HOT water
label instructions for treatments to avoid
by testing
stain
on
remover on an
set stains.
can
specific fabrics.
inside
Follow fabric
care
label
instructions
seam.
Stain Removal
STAIN
TREATMENT
Adhesive tape, chewing gum,
rubber cement
Apply ice.
Baby formula, dairy products, egg
Beverages (coffee, tea, soda, juice,
alcoholic beverages)
Use product
Blood
Scrape off excess. Place stain face down
nonflammable dry cleaning fluid.
containing
Pretreat stain. Wash
enzymes to
paper towels. Saturate with prewash stain
remover or
pretreat or soak stains.
using COLD water and bleach safe for fabric.
Rinse with COLD water. Rub with bar soap. Or pretreat
bleach safe for fabric.
Candle wax, crayon
on
or
soak with product
containing enzymes. Wash using
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
soak in WARM water using product
containing enzymes. Wash using bleach safe for fabric.
prewash stain remover or rub with bar soap.
Chocolate
Pretreat
Collar or cuff soil, cosmetics
Pretreat with
Dye transfer on white fabric
Use packaged color remover. Wash
Grass
Pretreat
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
motor
oils)
Ink
Mildew, scorch
Mud
Mustard, tomato
or
or
using bleach safe for fabric.
soak in WARM water using product
containing enzymes. Wash using bleach safe for fabric.
Some inks may be impossible to
remove. Washing may set some inks. Use prewash stain remover, denatured
dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
alcohol
or
nonflammable
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paint, varnish
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
Rust, brown or yellow
For
discoloration
Shoe polish
spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
: Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
LIQUID
safe for fabric.
BeforStaingWsh
14
F
BeforStaingWsh
unction of each Button
WATER TEMPERATURE
WATER LEVEL BUTTON
BUTTON
(INDICATION OF DETERGENT AMOUNT)
(OPTION)
Use to select Water
?
?
Temperature.
Pressing the button allows
WARM
(HOT&COLD)
HOT
COLD
Use to
adjust the WATER LEVEL as required. The
appropriate amount of Detergent is shown next to the
WATER LEVEL in the WATER-DETERGENT
?
you to select COLD
respectively.
Default setting is COLD.
?
option
selections
LARGE
LARGE EX-LARGE
SMALL
SMALL
MEDIUM
LARGE
the button is
pushed.
can
Adjustment can be made
washing.
MEDIUM
-
?
MEDIUM
Alarm indication -When
LARGE
Use to set
The time increases when the button is
?
while
delayed finishing time.
pushed.
The following settings
the button is pushed 3
...11
48
?
a
12
14
16
delay time,
switch off.
(refer to page 24)
occurs,
an error
WASH. RINSE. SPIN BUTTON
?
?
are
indicated
4
as
5
wash, rinse, spin
?
?
adjusted.
The time increases when the
button is
...46
turn the power
Use when
time need to be
3 HOUR.
To cancel
an error
message appears to indicate the abnormality.
For example,
indicates that the lid is open.
?
be
selected for any program, but when
washing jeans, it starts with Strong.
?
DELAY START INDICATION
?
light up in
This
?
(RESERVATION) When DELAY START
(RESERVATION) program is selected, it
indicates the finishing time. (RES.=DELAY)
EX-LARGE
.
During operation, the remaining time
-
is indicated.
diagram
DELAY START (RESERVATION) BUTTON
sequence as follows NORMAL ?N
STRONG ?N GENTLE ?N NORMAL
as
Time left
automatically selected for FUZZY
(normal) program.
The following settings are indicated as the button is pushed
This button allows you to select the
strength of the water current.
Power
?
WATER LEVEL is
STAIN LEVEL BUTTON
?
TIME LEFT, DELAY START
(RESERVATION), ALARM INDICATION
pressed
adjustments are needed
during the wash, press the
[start/pause] button before
making any changes.
When the button is pressed
during washing, the remaining
time is displayed.
.
If
NOTE
*
For
optimizing the washing algorithm, the displaying time may be changed during washing-increased by
by 4 minutes at maximum.
If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically
adds rinsing, and the remaining time may be increased.
The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to
the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.
The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a
liquid one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased.
8minutes at maximum and decreased
*
*
*
15
WASHING CONDITION INDICATOR
?
?
It only operates in FUZZY Program.
During being detected by the sensor, the LED flashes green, orange
and red in turn. And, after detecting, the LED lights a specific color according to the detecting condition as
follows:
If the current
washing
condition
(Detergent quantity,
Water
Temperature,
water
quality, etc.) is
determined
as
better than the standard one, it optimizes the algorithm to save the energy by decreasing washing time/strength,
and the LED automatically turns to red.
If the current washing condition is determined as worse than the standard one, it optimizes the algorithm by
increasing washing time/strength, and the LED automatically turns to orange.
If the current
washing
condition is determined
as
equal to the
standard one, the
algorithm has no change
and the
LED turns to green.
AUTO OFF
(POWER) BUTTON
?
?
?
CHILD LOCK FUNCTION
?
Use to lock
or
The power goes off automatically about
10 seconds after the wash is finished.
START/ PAUSE BUTTON
PROGRAM BUTTON
unlock the control
buttons to
Use to turn the power on or off.
Push again and power goes on or off
?
?
from
prevent settings
being changed by a child.
To lock, push the RINSE and
SPIN buttons simultaneously and
to unlock push them one more
time during the washing process.
Use for
selecting wash program.
This button allows you to select 8
different programs for different kinds of
laundry
?
and dirtiness.
program selections light up in sequence
follows: FUZZY (NORMAL)
DELICATE
WOOL
(refer to page 25)
ECONOMY
SILENT
TUB CLEAN
?
?
Use to start
or
pause the
washing process.
Repeats start and pause by
pushing the button.
as
JEAN
FAVORITE
FUZZY
(NORMAL)
by
etc. Select the desired program
pressing
*
Because the
may be decreased by using it for a long time, periodically use
(refer to page 21)
Even if the water level or the water temperature are changed by the user in FUZZY(Normal) Program,
the sensor will still work. The sensor algorithm may differ according to models.
The control panel may differ according to different models.
detecting ability
TUB CLEAN
*
*
course
of the
the button.
sensor
to clean the tub.
BeforStaingWsh
16
W ashing Programs
WashingProm
Add
the
Washing
Programs
Add
the
laundry
FUZZY Wash
1
Detergent
2
4
(Normal Wash)
Used for normal loads, this
mode automatically selects the
most appropriate conditions
and completes the sequence
in one operation. The built-in
sensor detects the size of the
load and the ideal wash
power and wash, rinse and
spin times are set accordingly.
Add the
appropriate
quantity of Detergent as
indicated by the WATER
LEVEL next to
WATER DETERGENT.
Or follow the Detergent
manufacturer's instructions
1
3
ECONOMY Wash
Use this mode when
lightly
time. The
laundry
highly
Select the
ECONOMY
washing
soiled clothes for
a
program
on the
Control
short
recommended
amount is under
2.0kg.
JEAN Wash
5
2
panel.
1
Use Jean program when
Jeans of different sizes
3
Spread
the jean
evenly in
the tub
washing
1
3
Add the
appropriate
quantity of Detergent as
indicated by the WATER
LEVEL next to
WATER DETERGENT.
Or follow the Detergent
manufacturer's
instructions
5
2
Select the
JEAN program
on the
Control panel.
5
2
WOOL Wash
Use this program for washing delicate
fabrics such as lingerie and woolens.
Select the
WOOL
(wash only "water washable" clothes)
Before washing your woolens check
the care label for the washing
program on
the Control
panel.
(wash only water washable clothes)
DELICATE
This would include
1
3
blouses,
nylons and dress shirts with
light soiled.
5
2
¡GSelect
action.
Detergent
appropriate for the
laundry.
When washing
woolens use a
mild Detergent
recommend- ed
for washing wool.
instructions.
Use this program to wash items
requiring a GENTLE WASH
Use neutral
the
DELICATE
program on
the Control
panel.
17
Close the lid
3
Finish
5
Caution & Note
6
If water is
wet
already in the tub, or putting
laundry into the tub before starting
will increase the WATER LEVEL.
The pulsator rotates for
8 seconds to detect the
laundry load.
Water will be
supplied for 2
minutes after the
When the wash
program ends, the
buzzer will ring
Then the WATER LEVEL
and the amount of
start of the wash to
for 10 seconds
before the Power
Detergent to be used
will be shown and
water will be
supplement the
water the laundry
has absorbed.
goes off
automatically.
supplied.
With
lightweight bulky loads,
LEVEL
can
WATER
be set low.
Changes to Water Temperature
(HOT/COLD) and wash level are
possible during operation.
(refer to page 14)
7
4
6
4
6
7
4
6
7
When
setting the WATER LEVEL
manually, do not set to Medium to
prevent damage to laundry.
Washing with HOT water may damage
the laundry (Water is set to cold
automatically). Ensure that the load is
under 2kg.
In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing
may still contain
normal.
4
6
7
some
water. This is
¡GBefore starting to wash, make sure that
the laundry is washable.
Washing with HOT water may damage
the laundry (Water is set to COLD
automatically).
Ensure that the load is under 2kg.
WashingProm
18
S
WashingProm
OAK Wash
Use this mode to wash normal clothes
SOAK mode can be used with FUZZY
or
or
thick and heavy clothes which are excessively
JEAN or SILENT or FAVORITE program.
1
Press the AUTO OFF
2
Press the PROGRAM button to select the
(POWER) button
dirty.
to turn power on.
washing
program.
SOAK will not work in WOOL and
ECONOMY,
DELICATE, TUB CLEAN Program.
3
Press the WASH button, to select SOAK program.
?
Keep pressing the WASH button until
light turns on¡fiSoak¡fland¡fiWash¡fl
simultaneously as next image.
SOAK program only works when
socking time is 40, 50 or 60 minutes.
the
?
4
Add the
Detergent.
The
appropriate quantity of Detergent marked next to the
WATER LEVEL of WATER-DETERGENT.
5
Add the
laundry
and press the START/PAUSE button.
The WATER LEVEL and the amount of Detergent to be
used will be shown and water will be
6
supplied.
Water will be
Close the lid.
wash to
Finish
supplied for 2 minutes after the start of the
supplement the absorbed water by the laundry.
When the wash program ends, the buzzer will ring for
10seconds before the Power goes off automatically.
NOTE
Order of Soak-Wash
?
min
?
Select
soaking
min
?
min
time
the Wash button
timing
Soak-Wash
min
min
40minutes, 50minutes,
min
or
Lamp
Off
60minutes
min
min
min
min
(including washing time) by pressing
repeatedly.
If necessary, select the times of Rinse and the time for
buttons till you reach the desired times.
Spinning by pressing
the Rinse
or
Spin
min
19
F AVORITE Wash
Pressing the
cycle
normal
FAVORITE button allows you to store your FAVORITE wash conditions in the
memory and then recall it for use at a later time.
1
Press the AUTO OFF
2
Select the FAVORITE program.
3
Select your FAVORITE wash conditions.
(POWER) button
WashingProm
to turn power on.
?
Press the WATER TEMP. button to select wash Water
?
Press the WATER LEVEL button to select
?
Press the STAIN LEVEL to select STRONG
Temperature.
WATER LEVEL.
wash
?
or
GENTLE
option.
Press the WASH
button, the RINSE button & the SPIN
time, rinse time & spin time
button to select wash
respectively you want to
4
store.
Press the START/PAUSE button to store & start your FAVORITE wash
Power turns off automatically after wash.
NOTE
To recall your FAVORITE
1. Press POWER
cycle.
on.
2. Select the FAVORITE
cycle by pressing
the PROGRAM.
3. Press the START/PAUSE button. Then the wash
cycle
starts.
cycle.
20
S
WashingProm
ILENT Wash
Use this program to wash
quietly
in SILENT
especially during
late
1
Press the AUTO OFF
2
Press the PROGRAM button to select SILENT program.
3
Add the
4
Press the START/PAUSE button.
5
Add the
laundry
(POWER) button
into the
Detergent
washing
night
and dawn.
to turn power on.
tub.
and close the lid.
NOTE
?
SILENT program takes
?
To reduce noise in
more
longer washing
spinning, spin
moisture than normal.
time than FUZZY
(Normal)
rpm is lower than normal
program.
spinning rpm.
So the
laundry
has
21
T UB CLEAN
If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in
your washer.
Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact
with Detergent, and according to particular degree of dirtiness or quality of water to be use,
in these case, use this program to clean inner tub and outer tub.
1
Press the POWER button to turn power
2
Press the PROGRAM button to select the TUB CLEAN program.
on.
Ex-Large WATER LEVEL is
3
automatically.
Press the START/PAUSE button.
?
4
set
Left time is
displayed.
After 10 minutes of water
5
?
Do not
?
Do not
supplement.
Add the
oxygenated
bleach
(about
300
m
).
box.
Detergent
place any laundry inside tub.
use
Close the lid.
¥When
the lid is open the machine will not operate, and
will remind you to close the lid.
alarm
signal
NOTE
?
Before
?
When
?
This program takes about 3 hours to be
?
After
using
?
After
finishing
?
Do not pour bleach into the tub
?
Do not leave diluted
?
Use this program
?
Do not
using
using
this program
remove
this program, do not
this program,
remove
lint inside lint filter.
place
any
laundry
completed.
dirt inside filter.
this program, open the lid of wash to
directly.
oxygenated bleach
It
might
once
for every month.
this program
repeatedly.
remove
cause
irritant odor.
damage
the tub.
inside tub for
It rusts the tub must drain the remained diluted
use
inside tub.
long time.
oxygenated water
out.
an
AditonalFucPrgm
22
0 ption Washing
When you
AditonalFucPrgm
1
only
need the
Press the AUTO OFF
2
Wash, Wash/Rinse
(Power)
or
Rinse
button to turn power
Only Wash
timing.
these
can
be set
manually.
on.
Only Wash,Rinse
Press the WASH button to select the
desired
cycles,
(refer to page 14)
Press the WASH button to select the
desired timing.
(refer to page 14)
Press the RINSE button to select the
desired times of rinse.
(refer to page 14)
can use this option for
wrinkles of laundry
You
3
preventing
Press the WATER LEVEL button, to control the water level according to the
laundry. If you do not choose anything, it is set the middle water
level automatically.
(refer to page 14)
amount of
4
Add the
5
Press the START/PAUSE button.
6
Add the
laundry
into the
detergent
washing
tub.
and close the lid.
23
1
Press the AUTO OFF
2
Only
(Power)
button to turn power
on.
Only Spin/Only drain
Only Rinse,Spin
Rinse
Press the RINSE button to
Press the RINSE button to
Press the SPIN button to
select the desired times of
select the desired times of
select the desired times of
rinse.
rinse. (refer to page 14)
spin.
(refer to page 14)
(refer to page 14)
Press the SPIN button to
select the desired times of
spin.
3
(refer to page 14)
When you want to only
drain, wait until the water in
the washing tub drains
completely.
Press the WATER LEVEL button to control the water
to
level according to the amount of laundry. (refer page 14)
4
Add the
5
Press the START/PAUSE button.
6
Add the
laundry
into the
detergent
washing
tub.
and close the lid.
NOTE
When
a
Wash,
Wash/Rinse
or
Rinse
only option is selected,
after the wash is
completed the water will not
be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained
completely. Then press the START/PAUSE button.
If you do not
If
only
specify the water level, then Medium will be automatically selected.
selected, the process will start from Water Supply.
Rinse is
AditonalFucPrgm
24
D
AditonalFucPrgm
ELAY START
(RESERVATION) Wash
DELAY START (RESERVATION) Wash is used to delay the finishing time of the
The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time not the start time.
operation.
,
1
Press the POWER button to turn power
2
Press the PROGRAM button to select the
on.
washing
program.
Select the program for laundry on the Control panel.
This program will not work in WOOL and DELICATE
Program.
3
Press the DELAY START
button.
(RESERVATION)
?
The
light will
'
DELAY' turn
'TIME LEFT'
?
on
and
will be marked.
Press the button
repeatedly to set the desired finishing time.
washing in 9 hours from now, by
make the number 9:00 pressing the DELAY START
(RESERVATION ) button repeatedly.
For
To finish
example,
(RES.=DELAY)
4
Add the
The
Detergent.
of
appropriate quantity
Detergent marked next to
the
WATER LEVEL of WATER?DETERGENT.
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid
5
Add the
laundry
and press the START/PAUSE button.
When you press the START/PAUSE button the
blink.
6
an
Close the lid.
Water will be
Finish
The
wash to
light will
supplied for 2 minutes after the start of the
supplement the water the laundry has absorbed.
washing
will be finished
according
to the
delayed time.
NOTE
?
Finishing
time
can
be
delayed from
3~48hours.
Delaying
from3~12hours
can
be done in 1 hour time intervals
and from 12~48hours in 2 hour time intervals.
?
?
If the lid is open, the machine will not work, and an alarm
To select washing time, rinsing times, spinning time, water
DELAY START
?
When the
program
.
signal
will alarm to remind you to close the lid.
level, hot/cold or wash power manually, press the
(RESERVATION) button and select the desired option. Then press the START/PAUSE button.
laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning
(The laundry will be wrinkled if left for a long time after spinning.)
25
O
ther Useful Functions
Child Lock Function
If you want to lock all the
child lock
keys
to
prevent settings from being changed by
a
child,
you
can use
the
option.
How to Lock
1
Press the POWER button.
Turn Power
2
Press the START/PAUSE button to start
washing.
After all
3
on.
washing conditions are set according
Press both the RINSE button and the SPIN button
to the manual.
simultaneously.
During the wash program, all the buttons are locked
until washing is completed or it is child- lock
function is deactivated manually.
How to Unlock
If you want to unlock
during wash,
press both the RINSE and the SPIN button
simultaneously again.
NOTE
"
Mute
"
& the
remaining time are alternatively shown
on
the
display while they are
locked.
Option
If you want to use the washing machine without alarm
buttons simultaneously.
To make buzzer
one more
time.
Time
remaining time for each process, press one of the WASH, RINSE
The remaining time for each process will appear for about 1 second.
see
the
both the WASH and SPIN
work, press both the WASH and SPIN buttons simultaneously
Seeing Remaining
To
signal sounds, press
and SPIN buttons.
AditonalFucPrgm
26
P lacing and Leveling
Please
ensure
that transit restraint has been removed before
your machine.
operating
Instal ion
1
Place the machine
on a
flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2 cm to the
right side and left sides of the machine for ease of
more
than 10
cm
installation.
At the rear,
a
minimum clearance of 10
cm
is
suggested.
more
than
2cm
more
than
2cm
NOTE
If the washer is installed
on a uneven,weak or tilted floor causing excessive vibration,
error can
spin failure or
happen to it.
It must be placed on a firm and level floor to prevent spin failure.
"
2
"
Check that the machine is level
Open the lid and look from above to
same as
3
see
if it is
Top
view of the machine
shown.
the machine
Leveling
Lift the front of the
washing machine and twist
Adjustable Leg until the surface bubble is
placed in the center.
the
Adjustable legs
Level indicator
Caution
If the power is supplied from a cord extension set or generator, the cord extension set or
electrical portable outlet device should be positioned so that it is not exposed to splashing
ingress
of moisture.
or
27
C
onnecting Water Supply Hose
Before connecting the Water Supply Hose to the water tap, check the hose type and
then choose the correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country, Make
sure to connect the blue inlet hose to the COLD water tap, and the orange inlet hose
to the HOT water tap.
Connecting
Water
Normal
1
Type
Untighten
Untighten
tap
2
can
Fixing
Supply
be
the
Hose to water tap
(Normal tap
the
without thread &
screw
type inlet hose.)
Rubber
screw
screw
of the connector
so
packing
that the
screw
placed in the middle.
Connector
the connector to the tap
Push the upper connector up till the rubber
Then
packing is in tight contact with the tap.
tighten the 4 screws.
3
Attach the water
supply
hose
securely
to the
connector
Push the water
supply hose vertically upwards
that the rubber seal within the hose
completely
to the
can
Connector
so
adhere
Water
tap.
Supply
4
Fixing
the connector to the water
supply
Hose
hose
Attach the water
then
5
tighten
it
supply hose to the connector and
by screwing it to the right.
Check the connection of water
supply
hose and the connector
After
connecting the hose, open the tap to check
for any water leakage.
If the water leaks, close the tap and start again
from
step 1
NOTE
The
washing machine is
not be reused.
to be connected to the water mains
using
new
hose-sets and old hose-sets should
Instal ion
28
onnecting Water Supply Hose
C
Instal ion
Normal
1
Type
(Normal tap without thread
&
one
Middle connector from Water
Separate
touch type inlet hose.)
Supply
Middle connector from the Water
Separate
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
Hose
Middle
Fixed Sticker
connector
Pressing
Handle
Pressing
Rod
Water
2
Supply
Hose
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector
tap can be placed in the middle.
that the
so
Rubber
packing
screw
Fixed sticker
NOTE
In
tap is
case
If the
tap
Guide
large.
too
diameter is too
plate
large is square,
and remove the guide
Rubber
or
packing
untighten the 4 screws
plate. Then follow step1.
3
Fixing
Connectors to the
Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten
4
the 4
screws.
Connector and Middle Connector
Fixing Upper
Remove the fixed sticker in between the
and Middle Connectors.
by holding
one
Tighten the connectors
Middle
connector and twist middle
connector to the
5
Connector
Upper
Connector
Fixed sticker
right.
Connecting
Middle Connector and Water
Supply
pressing rod of the Water Supply
separated from middle connector
(refer to Step1) and then join it to the middle
Connector
Middle
Connector
Hose
Press down the
Hose which
was
Pressing
rod
connector.
Water
6
Check for water
leakage
After
connecting the hose,
for any water leakage.
If the connection
open the
tap
to check
leaks, close the tap and
again from step 1.
If you skip step 1,
water
leakage may
start
occur.
Supply
Hose
Pressing
handle
29
Screw
1
Instal ion
Type
Attach the water
supply
hose to the tap.
Push the water
packing
the
supply hose up so that the rubber
within the hose can adhere completely to
tap.
Water
tap
Rubber
Water
2
Connect the water
supply
Connect the water
hose to the
supply
tighten it by screwing it to
3
Check water
connecting the hose,
for any water leakage.
?
Water
Supply
hose to the tap.
tap and then
right.
leakage.
After
Connecting
the
Packing
open the
Supply
tap
to check
Hose to the machine
Connect the water
supply hose to inlet valve of
washing machine, and then lock it by turning
the hose connecting part.
the
?
Check to
see
if there is
a
rubber seal inside the
Hose connector
connector.
Rubber seal
Hose
30
Drain Hose
C onnecting
Before connecting Drain Hose, check your Drain Hose model and choose the correct
instructions.
Instal ion
Pump
Model
1
Fit the end of the drain hose to the outlet of the
2
Put the other end of the drain hose over the
drain pump and
tighten the clamp.
standpipe or
wash tub.
Hose
Guide
W ith in 50
mm
0.9~1.2m
Drain Hose
NOTE
To
prevent siphoning, the drain hose should
The
discharge height
Non-Pump
1
Before
should be
not extend
approximately
0.9
more
1.2
~
m
than 50
mm
from the end of the hose
from the floor.
Model
connecting
Ensure that the hose
clip
is set
as
indicated here.
Clip
2
Connect the Elbow Hose
Push the elbow hose toward the
body
of the
washing machine.
3
Place the Drain Hose
To
change the direction of the hose, pull
change the direction.
Repeat Step 2.
elbow hose and
out the
guide.
31
G rounding
Method
Earth wire should be connected.
If the earth wire is not connected, there is
caused by the current leakage
possible
a
danger
of electric shock
.
Grounding
Method with Ground insert space Terminal
Ground
If the AC current outlet has
ground terminal, then
separate grounding is not required. Note that AC power
outlet configurations may differ from country to country
Terminal
a
Outlet with
ground
terminal.
Caution
CAUTION
concerning
the Power Cord
Most
appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers
only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's
manual to be certain. Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets,
damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
extension
cords, frayed power cords,
attention to
Other
Grounding
plugs,
wall
outlets, and the point where the cord exits the appliance.
Method
Burying Copper
Plate
Connect the Ground Wire to
Plate and
or
bury it
more
a
Ground
Copper
ground.
than 75cm in the
Ground Wire
75cm
Ground
Using
Connect the
ground Wire to
exclusively for Grounding.
Using
Copper
Plate
Ground Wire
a
the socket
provided
Ground
Wire
Short Circuit Breaker
If grounding methods described above are not
possible, a separate circuit breaker should be
employed and installed by a qualified electrician
Short-circuit
breaker
Caution
?
To
?
Do not connect
prevent a possible explosion, do
?
Connecting ground to plastic
?
Ground wires should be connected when
ground
to
ground to a gas pipe
lightning rods. This may be dangerous during electrical
not connect
telephone wires
or
storms
has
no
effect
an
extension cord is used.
CarendMitc
32
and Maintenance
C leaning
CarendMitc
Cold water
?
If you
washing
always use
COLD water,
we
recommend that
intervals e.g. every 5th wash should be at least
a
a
WARM
WARM
or
HOT wash be used at
a
regular
as
sand),
one.
When you have finished
?
?
Turn off taps to prevent the chance of flooding
Always unplug the power cord after use.
When water supply into the tub is not clean
filter in the inlet valve occasionally.
(The figure
of power cord and water
or
should
the filter is
a
hose burst.
clogged
tap may vary according
with
to the
particles (such
clean the
country)
To Clean the Filter in the Inlet Valve
1
Close the
tap before turning off the power.
Select both HOT/COLD and then press the
[START/PAUSE] button to remove water
from the machine
3
2
completely.
After
removing the water supply
hose pull out the filter.
Then
use a
Turn off the power before
pulling out the cord.
4
Replace the filter after cleaning it.
brush to clean the filter.
NOTE
?
Before
cleaning
the
filter, the impurities in the
water
supply hose
should be removed.
To Clean the Lint Filter
1
2
Pull out the lint filter from
3
Turn the net inside out
the tub in the direction
to clean the filter and
shown below.
rinse it with water.
Replace- the filter to the
original location. Push the
lip of the filter until a pop
sound is heard.
NOTE
?
If the lint filter is torn
To Clean the
1
or
damaged, purchase a
new one
from LG service center.
Pump casing (for pump model)
Place a towel on the
floor under the drain
pump cap. Excess
water may flow out.
2
Turn the cap
counter-
clockwise and
pull it
Cap
out.
3
Remove any
foreign
objects and fluff inside
pump casing and from the
4
filter.
Replace the cap. Insert the filter along
the guide ribs inside the pump casing.
Filter must face the guide ribs inside
pump casing and securely turn the cap
clockwise.
Filter
Guide rib
Filter
NOTE
?
Check if water leaks after
reassembling. (The
Rubber
ring is
in the
cap)
33
C leaning
and Maintenance
When there is a fear of
?
Close the water
freezing
taps and remove the Water Supply Hose.
?
Remove the water which remains in the water
?
Lower the drain hose and drain the water in the bowl and the drain hose
supply.
by spinning.
If frozen
Remove the water supply hose, and immerse it in HOT water at approx.. 40˚C.
Pour approx.. 2 liters of HOT water at approx.. 40˚C, into the bowl and let it stand for 10 minutes.
Connect the water supply hose to the water tap and confirm that the washing machine performs the
?
?
?
supply and drainage
Wash Inner-tub
of water.
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
use a clean soft cloth dampened with liquid Detergent, then rinse. (Do
the inner-tub
not
Inlet Hoses
harsh
use
connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
sharp objects.
Long Vacations
Be
sure
water
be below
supply
freezing.
do
or
regular
?
Fill your washer with HOT water.
?
Add about two cups of
?
Let it
?
surface with
is shut off at faucets. Drain all water from hoses if weather will
the Inside of your Washer
If you use fabric softener
inside of your washer.
?
gritty cleaners.)
Hoses
Exterior
Cleaning
or
a
COLD water
washing, it is
very
important that you occasionally clean the
powdered Detergent that contains phosphate.
operate for several minutes.
Stop the washer, open the lid and leave it to soak overnight.
soaking, drain the washer and run it through a normal cycle.
After
Or
use
TUB CLEAN PROGRAM
periodically.
during this procedure.
We do not recommend that you wash clothes
Products that
might damage your washing
Concentrated bleaches and
?
Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint
(Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in
washer or dryer.)
?
Some
?
Use of
but
pretreatment sprays
we
diaper
or
sanitizer will
machine
?
Do not
damage to the paintwork and components
of your washer.
liquids can damage your washer's control panel.
in your washer may cause staining of the plastic components. The dye will not damage the machine
suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in
dyes
your washer.
?
cause
use
your washer lid
as a
work surface.
CarendMitc
34
C
Troubleshting
ommon
washing problems
Many washing problems involve poor soil & stain removal, residues of lint and
damage. For satisfactory washing results, follow these
scum, and fabric
instructions.
WASH PROBLEM
Problems
Poor soil
removal
Solutions & Preventive Measures
Possible Causes
?
Not
?
Wash Water
enough Detergent
Temperature
too low.
?
?
?
?
?
the washer
Use WARM
or
amount of
HOT water for normal soil.
Different Water Temperature may be
Incorrect wash
cycle
Incorrect sorting
Do not pretreat stain
size,
soil and water Hardness.
?
Overloading
Use correct amount of Detergent for load
soil type.
required according to
(refer to page 10)
?
Reduce load size.
?
Wash with JEAN
or SOAK & JEAN wash cycle for heavy
laundry.
Separate heavily soiled items from lightly soiled ones.
Pretreat stain and heavy soil according to directions shown
soiled
?
?
on
Blue Stains
?
Undiluted fabric softener
dispensed directly
onto
page 9.
?
Rub the stain with bar soap. Wash.
?
Do not overfill fabric softener
fabric
dispenser and do not pour
liquid fabric softener directly onto fabric.
See page 12 for
Black
marks
?
or
gray
A
caused
buildup
by the
and
clothes
Detergent
can
Yellow or
brown rust
Keep the recommendations against Scrud(waxy buildup).
(refer to scrud page12.)
?
Use correct amount of Detergent for load
flake off
and mark clothes
?
?
Not
Iron
or
stains
or
manganese in
supply,
water
?
pipes,
water heater
size,
amount of soil
and water Hardness.
enough Detergent
water
instructions.
?
interaction of fabric softener
on
more
To restore discolored load of
whites,
use
rust
remover
safe
for fabric.
?
Install nonprecipitating water softener
or an
iron filter in
supply system for an ongoing problem.
Before washing, run water for a few minutes to clear lines.
your water
?
Lint
?
?
?
Incorrect
sorting
pocket
Overloading the washer
?
or
Detergent
Holes, tears,
or
?
Overloading
?
Undissolved
?
Use too
?
the washer
Detergent
much Detergent
Incorrect
use
of chlorine
?
?
?
?
Unfastened
zippers,
hooks, buckles
Ribs, tears and broken
?
Overloading
Degradation
Do not overload the washer.
Some Detergents need to be
pre-dissolved, check the Detergent
Try pre-dissolving the Detergent.
?
Increase Water Temperature using HOT water safe for fabric.
?
Use proper amount of Detergent.
?
Never pour chlorine bleach
See page 11 for
directly on fabric.
adding liquid bleach.
zippers, hooks, and buckles.
?
Fasten
?
Remove
threads
?
synthetic fabrics and remove tissues in
sorting and caring
See page 9 for
Do not overload the washer
instructions.
bleach.
snags
givers eg towels, flannelette sheets, separately
pockets before wash.
before loading.
?
Residue
Wash lint
from lint collectors eg
Tissues left in
objects in pockets.
loading.
the washer
of fabric
?
Do not overload the washer.
See page 9 for
caring before
35
T roubleshooting
Before
calling
Symptom
Water Supply
Failure
for service, check the
Error
Message
.
.
.
.
.
Failure
the list bellows.
Troubleshting
Check up
.
Drainage
problem against
Is the water
tap shut off?
Is the water
supply cut off ?
water supply hose frozen
Is the
tap
or
?
Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
Is the Hot hose connected to cold?
Is the Cold hose connected to hot?
.
Is the drain hose
.
Is the drain hose bent
.
Is the internal
positioned correctly?
or
placed too high?
part of the hose or drain pump
(only pump model) clogged with impurities?
.
Spin
Failure
Door(Lid) Open
.
Is the
laundry evenly balanced?
.
Is the
washing machine placed on a
.
Is the lid closed?
.
Internal sensing
failure
Power failure
Overflow failure
Check if electric power has gone off.
flat surface?
Please call your nearest LG Electronics service center
for help.
36
T
erms
of
Warranty
What Is Not Covered:
?
?
?
?
trips to your home to teach you how to use the product.
product is connected to any voltage other than that shown on the rating plate.
If the fault is caused by accident, neglect, misuse or Act of God.
If the fault is caused by factors other than normal domestic use or use in
Service
If the
accordance with the owner's manual.
?
Provide instruction
?
If the fault is caused
change the set-up of the product.
by
example, rats or cockroaches etc..
Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
Correcting the installation for example, levelling the product, adjustment of drain.
Normal maintenance which recommended by the owner's manual.
Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
Replace fuses in or correct house wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects
with this appliance.
If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training center,
dormitory)
on use
of product
or
pests for
?
?
?
?
?
?
?
?
If the
product is installed outside the normal service area, any cost of transportation
repair of the product, or the replacement of a defective part, shall be
borne by the owner.
involved in the
37
S pecification
Specifaton
H
D
W
Model
WFT10(1)C60(1)D(E,F)C(H,P,D,E,F,M)
WFT15C61EF / WF-T1111D / WF-S1250
Size
632(W)
x
670(D)
x
980(H)
WFT10(1)C60(1)D(F)
632(W)
x
670(D)
x
1005(H)
WFT10(1)C60(1)E
~
~
WFT15C61EF / WF-T1111D / WF-S1250
Water tab pressure
In
our
to the
30
-
800 kPa
(0.3
-
8.0
2
kgf/cm )
continuing effort to improve the quality of our appliances,
appliance without revising this manual.
it may be necessary to make
changes
M
emo
P/No.: 3828EA3027V
Download PDF