LG | WF-T8019TH | LG WF-T8019TH Owner’s Manual

Washing
Machine
OWNER'S MANUAL
MODEL
:
WF-T5001(~5)PP(H,C,D,E,F)/ T5011(~5)PP(H,C,D,E,F)
WF-T5021(~5)PP(H,C,D,E,F)/ T5501(~5)TP(H,C,D,E,F)
WF-T5511(~5)TP(H,C,D,E,F)/ T5521(~5)TP(H,C,D,E,F)
WF-T6001(~5)TP(H,C,D,E,F)/ T6011(~5)TP(H,C,D,E,F)
WF-T6021(~5)TP(H,C,D,E,F)/ T7001(~9)PP(H,C,D,E,F)
WF-T7011(~9)PP(H,C,D,E,F)/ T8001(~9)TP(H,C,D,E,F)
WF-T8011(~9)TP(H,C,D,E,F)/ WF-T7008TH
Please read this manual
carefully
before
operating your
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
cover
information to your dealer when you
and
require
quote this
service.
set.
P
roduct Features
"Turbo Drum" washer doesn't operate while the lid is open. If the lid is open
during the wash, rinse or spin cycles, the operation stops for safety.
Fuzzy logic control
A built-in load
automatically detects the laundry
microprocessor optimizes washing
load and
sensor
conditions such
as
ideal
water
level and
START
SENSING
Laundry Sensor
Water Level Sensor
a
SETTING
Optimum
Washing
WASHING
Condition
washing time.
Advanced technology is
the best washing result.
Turbo drum
built into the Electronic Control
System
which
AUTO
POWER
OFF
ensures
washing
When "Punch
+ 3"
washing wings turn, the washing tub turns in
opposite direction. This makes the both sides current of water
which improve wash-performance by rubbing clothes strongly.
the
Innovated
washing wings
Three small
washing wings generate strong and sharp washing currents to
clean laundry uniformly.
Adjusted vertical movement and rotating directions of the washing punch
reduce laundry entanglement and improve washing performance.
3
Step washing
3
step washing makes the best washing performance with low tangling.
Rubbing and Shaking
Rubbing
Devices for
removing
Lint filters catch nap and thread
the
laundry
Shaking and Disentangling
nap
generated during washing to
make
cleaner.
Auto Restart
In the event of
a
interrupted cycle
※
Applied
models
power failure, the washing machine will
when power is resumed.
:
automatically
resume
WF-T5001(~5)PD(E/F),T5011(~5)PD(E/F),T5021(~5)PD(E/F)
WF-T5501(~5)TD(E/F),T5511(~5)TD(E/F),T5521(~5)TD(E/F)
WF-T6001(~5)TD(E/F),T6011(~5)TD(E/F),T6021(~5)TD(E/F)
WF-T7001(~9)PD(E/F),T7011(~9)TD(E/F)
WF-T8011(~9)TD(E/F),T8011(~9)TD(E/F)
its
C
ontents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
a little
preventive care on your part can save you a great deal of time and
over the life of
money
your washer. You will find many answers to common problems
properly. Just
in the
may
Troubleshooting
not
need
to
section. If you review
call for service
Introduction
Before
Starting
at
Safety
to Wash
chart of
our
Additional Function
Options
Installation
Care and Maintenance
you
Information
4
Identification of Parts
5
Function Information
6
Before
Preparation
Washing
Detergent, Bleach and Softener
Use of Water,
Washing Programs
Troubleshooting Tips first,
all.
7
8
How to Remove Stains
11
Function of each Button
12
Fuzzy Wash (Normal Wash)
14
Jean Wash
14
Wool Wash
14
Soak Wash
14
Economy Wash
14
Delay
Start (Reservation) Wash
16
Option Washing
17
Other useful Functions
18
Placing
and
Leveling
Supply
Connecting
Water
Connecting
Drain Hose
Grounding
Cleaning
19
Hose
Method
and Maintenance
20
23
24
25
Troubleshooting
Troubleshooting
27
Terms of
Terms of
30
Warranty
Specification
Warranty
Specification
31
4
S
afety
information
WARNING!
Read and follow this
Introducin
For your
safety
information
carefully.
the information in this manual must be followed to minimize the risk of fire
safety,
explosion, electric shock,
or
to
prevent property damage, personal injury,
or
or
loss of life.
Save these instructions.
?
WATER HEATER
Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more.
Hydrogen gas can be explosive under these circumstances. If the
hot water has not been used for two weeks or more, prevent the possibility of damage or injury
SAFETY
by turning on all hot water faucets and allowing them to run for several minutes. Do this before
using any electrical appliance which is connected to the hot water system. This simple
procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not
smoke or use an open flame or appliance during this process.
?
PROPER
Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather.
INSTALLATION
?
Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
YOUR
?
LAUNDRY
AREA
?
Keep the area underneath and around your appliances free of combustible materials such as lint,
paper, rags, chemicals, etc.
Close supervision is necessary if this
to
?
WHEN USING
?
THE WASHER
?
?
?
play on, with,
or
appliance is used by or near children. Do not allow children
inside this or any other appliance.
Use this
appliance only for its intended purpose as described in this Owner's Manual.
moving. Wait until the machine has completely stopped
before opening the lid.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing
different chemicals can produce a toxic gas which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as wax, oil, paint, gasoline, dry-cleaning solvents,
kerosene, etc.) which may ignite or explode. Do not add these substances to the wash water. Do
not use or place these substances around your washer or dryer during operation.
The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully
Never reach into washer while it is
follow the garment manufacturer's wash and care instructions.
?
To minimize the possibility of electric
shock, unplug this appliance from the power supply or
disconnect the washer at the household distribution panel by removing the fuse or switching off
the circuit breaker before attempting any maintenance or cleaning.
NOTE:
?
?
WHEN NOT IN
Pressing Power button to turn off does NOT disconnect the appliance
from the power supply.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a damaged cord or plug.
Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break
or
USE
?
?
?
rupture should occur. Check the condition of the fill hoses; they may need replacement after 5
years.
Before
discarding a washer, or removing it from service, remove the washer lid to prevent
children from hiding inside.
Do not attempt to repair or replace any part of this appliance unless specifically recommended in
this Owner's Manual, or in published user-repair instructions that you understand and have the
skills to carry out.
Do not tamper with controls.
5
I
dentification of Parts
Body
*
WATER SUPPLY
HOSE
POWDER DETERGENT
Make
BOX FOR DELAYED
sure
the water
does not leak.
WASHING
SOFTENER INLET
Softner will
*
POWER PLUG
automatically
If the
supply cord is
damaged, it must be
replaced by the
flow into the tub.
INLET HOLE FOR
manufacturer
BLEACH
or
its service agents
or
similarly qualified
person in order to
avoid a hazard.
FUNCTION SELECTOR
TUB
LINT FILTER
Clean
regularly
linting
START/PAUSE
on
to
stop
the clothes
load.
BUTTON
Use to start
or
stop the
washing machine
temporarily.
*
DRAIN HOSE
for pump model
Check if the drain hose
is
hung up before
operating the
washing machine.
*
DRAIN HOSE
for non pump model
LEVELING LEGS
Use to level the
washing
machine for correct balance
&
spin operation.
BASE
Accessories
Water
supply
hoses
Drain hose
Anti-rat
cover
or
or
1 Each for cold and
hot
water
Note
“
”Part
can
be different
according to
the model.
or
(option)
Introducin
6
Function
Information
Our machine
provides
various
types of laundry.
washing
methods which suits various conditions and
Different types of laundry washing
Fuzzy(Normal)
Use this
Wash
Program for everyday washing e.g. sheets, towels, T-shirts. (refer
to
p14)
Jean Wash
Use this
Program for heavily soiled durable garments e.g. overalls, jeans.
heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed.
Thick and
(refer
to
p14)
Wool Wash
Delicate clothes
(lingerie, wool, etc.)
which may be
easily damaged can be washed.
(refer to p14)
The fibers of machine washable woolens have been
specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
Before washing your woolens check the care label for the washing instructions.
?
?
?
?
When
washing woolens use a mild detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
tumble action of a
(The heat and
of woolen
dryer may
shrinkage felting
garments.)
underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.
(Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to
handwash these articles and place them in the machine to spin dry.
cause
or
Some wool
Washing according to the condition of laundry
Economy Wash
Economy wash can be selected to wash lightly soiled clothes
(refer
to
of less than 2.0
kg in a short time.
p14)
Soak Wash
Soak Wash
dirt and
can
be selected to wash
grime.
(refer
to p
heavily soiled laundry by soaking it in water for sometime to remove
14)
Other washing method
Delay
start
Wash
Delay start Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly.
(refer
to
p16)
Option Wash
When the
user
needs
only Spin, Rinse/Spin, Rinse, Wash/Rinse, Wash, Soak/Wash/Rinse/Spin,
Soak/Wash/Rinse, Soak/Wash.
(refer to p17)
7
Before
Preparation
Washing
BeforStaingWsh
Care Labels
*
Look for
a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Sort clothes into loads that can be washed with the
same
wash
cycle, water temperature and spin speed.
Sorting
To get the best
?
?
?
results, different fabrics need to be washed in different ways.
(Heavy, Normal, Light)
Separate clothes according to the type and amount of soil.
COLOR (Whites, Lights, Darks)
Separate white fabrics from colored fabrics.
LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
SOIL
Lint Producers
Terry cloth, Chenile, Towels, Nappies, Diapers
Synthetics, Corduroy, Permanent Press, Socks
Lint Collectors
Check before
?
Check all
pockets to make sure that they are empty. Things such as nails, hairclips, matches,
and keys can damage both your washer and your clothes.
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
pens,
?
?
?
?
?
Loading
coins,
Pretreat any dirt and stains.
Make sure the clothes are washable in water.
Check the
WIRE
washing instructions.
Loading
Do not wash fabrics
containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The water level should just cover the clothes.
Adjust the load size accordingly. Loosely load clothes no higher than the
top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional
items. Close the lid and press Start button
Light
and
again to restart.
Large-sized clothing
WARNING
Clothes like downs and woollens
large
and float
them in
a
easily.
Use
a
are light weight,
nylon net and wash
small amount of water.
If the
laundry floats during the
wash cycle, it may become damaged.
Use dissolved detergent to prevent the
detergent from clumping.
Long laundry
items
nylon nets for long, delicate items.
laundry with long strings
or long length
a net will prevent
tangling during washing.
Fasten zippers, hook, and strings to make sure
Use
For
,
that these items don't snag on other clothes.
※ Nylon net is not supplied by LG.
Fire Hazard
Never
items in the washer that
are
place
with
or
other
flammable
fluids.
dampened
gasoline
No washer can completely remove oil.
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
8
U
BeforStaingWsh
Using
of Water,
se
Detergent,
Bleach and Softener
water
Amount of Water Level
?
?
This machine detects the
will be shown
on
the control
The
?
When the water level is
following table
The machine sets the
?
You
be
used)
panel.
can
D
T
appropriate temperature automatically according to the wash program
change the water temperature by pressing the WATER TEMP button. (refer to p12)
The temperature of the water
.
impacts the effectiveness
results. We recommend temperatures of:
HOT 49~60°C...(120-140˚F)
White
-
-
-
WARM 29~40°C...(85-105˚F)
COLD* 18~24°C...(65-75˚F)
of all
laundry
additives and
items, diapers, underclothing
and
the
therefore,
heavily soiled,
cleaning
colorfast items.
Most items
Only very bright colors with light soil.
washing in cold water additional steps may be needed:
Adjust detergent amount and pre-dissolve detergent in warm water
When
-
-
-
-
*
(to
temperature
?
?
WATER.DETERGENT
EX-LARGE
LARGE
MEDIUM
SMALL
automatically detected, it may differ depending on the quantity of laundry even
though the same water level is indicated on the control panel.
The amount of a cup in the diagram is about 40g for concentrated detergent.
Water
?
then sets the water
shows the amount of water.
?
?
quantity of laundry automatically,
level and proper amount of detergent.
When you select a wash program, the water level and amount of detergent
Pretreat spots and stains
Soak heavily soiled items
Use
appropriate bleach
Temperature below 18°C...(65˚F) will not activate laundry additives and may cause lint, residue, poor
cleaning, etc. In addition, detergent manufactures and care labels define cold water as 26~29°C...(80-85˚F).If
the temperature of the water in the tub is too cold for your hands, the detergent will not activate and clean
effectively.
Using Detergent and
Fabric Softener
Detergent
detergent package directions. Using too little detergent is a common cause of laundry problems.
detergent if you have hard water, large loads, greasy or oily soils or lower water temperature.
Follow the
Use
more
Choosing
the
right detergent
use of domestic detergent, (powder, liquid or concentrated). Soap flakes or
Attention
granulated soap powders should not be used in your washing machine. When washing woolens
We recommend the
remember to
use
detergent suitable for washing woolens.
9
Using Detergent and
How much
Fabric Softener
detergent
When you select a wash program the water level and the amount of detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated
detergent.
The correct amount of detergent will vary depending on the amount of soil in your clothes
and work cloches may need more detergent, while bath towels usually need less.).
For
liquid
and concentrated
detergents,
follow the recommendations of the
(Jeans
detergent manufacturer.
Note: To check you are using the correct amount of detergent, lift the lid of your machine
about half-way through the wash. There should be a thin layer of foam over the surface of the
water. Lots of foam may look
foam
means
not
good, but it does not contribute to cleaning your clothes. No
enough detergent has been used; soil and lint can settle back on the clothes or
washing machine.
detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
the
If excess
Adding
the
detergent
Open the detergent dispenser and deposit the appropriate
Powder Detergent Box
amount of detergent
Where you deposit the detergent
Where you
Powder Detergent dispenser.
deposit the
Some detergents MUST be fully dissolved before
detergent
adding to your machine to get the best wash results.
Check the instructions on the detergent packet.
If you use powdered detergent it is essential that the required amount be fully dissolved in very hot water
before being added to warm or hot water for the actual wash.
Pre-dissolving detergent in warm water when washing in cold water can improve its performance.
10
U
BeforStaingWsh
of Water,
se
Detergent,
Available Fabric Softener
Do not
For
use
more
Type
concentrated fabric softener. This may cause some problems in automatic
products instructions for use.
Don't
softener
softener with
use
detergent.
Use softener in
last rinse water
?
?
?
?
dispensing.
details refer to the softener
Depositing Fabric
?
Bleach and Softener
Softener
When using dispenser, dilute
fresh water(30ml)
When filling dispenser, do not
It may stain clothes.
Never pour fabric softener
It may stain them
dispenser
softener(30ml) with
splash or overfill.
directly
or
clothes.
on
Softener
case
If
spotting occurs, wet and rub hand
dishwashing liquid (or mild bar soap)
and rewash.
Note
Fabric Softener will be
Using
dispensed automatically during the final rinse.
Bleach
Check fabric
care
labels for
Available Bleach
Use
special instructions.
Type
oxygenated bleach.
Powdered bleach should mixed with water and then be
For
more
details refer to the
deposited into
products instruction for use.
Depositing Bleach
?
?
the tub.
Bleach
Separate the laundry to be bleached
Measure liquid bleach carefully, following instructions
dispenser
on
the bottle.
?
?
?
Before
starting the washer, pour measured amount of bleach
directly into bleach dispenser.
Avoid splashing or over-filling dispenser. If you prefer to
use powdered bleach, add it into the wash basket with your
detergent.
The dispenser dilutes liquid bleach before it reaches into
your wash load.
Attention
Never pour undiluted liquid bleach directly onto clothes
This may cause change of color or damage the laundry.
or
into the wash basket.
Do not mix chlorine bleach with ammonia
as
vinegar and/or rust remover. Mixing can reduce
toxic gas which may cause death.
Do not pour powered bleach into bleach
or
acids such
a
dispenser.
11
How
To Remove Stains
How To Remove Stains
Pretreating dirt and stains
Brush a little washing detergent dissolved in water onto stains, collars, and cuffs to help shift dirt.
The secret of stain treatment is immediate action. When an accident happens, plunge the stained area
into cold water, or sponge it down. This prevents the stain from setting. Wash as soon as possible
afterwards.
?
?
?
Treat stains AS SOON AS POSSIBLE. The
stain,
?
Use cold
?
Some stains
as
or warm
are
this
can
water
not
water
care
as
reverse
force the stain off the fabric instead of through it.
unknown stains
seen
as
hot water
can
set
when the fabric is wet. Do air
heat from
may set the
some
dry
stains.
the stained garment to be
a
with stain removal treatments
sure
the
stain.
dryer
as they are often flammable and highly poisonous.
use them in your washer as they may damage the paint or plastic components.
Some pretreatment sprays or liquids can damage your washer's control panel.
Take
Diaper
?
on
easily
stain has been removed,
?
a
It pays to pre-wash products and solvents on an inconspicuous part of the garment first.
Place the garment being treated on an absorbent cloth (e.g. on an old towel). Work from the
side of the
?
longer they are left, the harder they are to remove.
Always consider the type of fabric you are treating to make sure you do not use
temperature that is too hot or a treatment that will alter the color of the fabric.
Do not
Sanitizers
Diaper sanitizers are very corrosive to metal surfaces. DO NOT soak diapers in sanitizers in your
or tip the contents of the diaper bucket into your machine. Rinse and wring diapers out
thoroughly before placing them in your machine.
washer
Diapers
?
Scrape off any excess baby cream, such as Vaseline from the diapers before washing and handwash
prevent the cream being transferred to other items in the wash.
to
12
F unction of each Button
BeforStaingWsh
Water
temperature button (option)
Water level button
(indication of detergent amount)
Use to select water temperature.
Pressing the button allows you to
Cold
Warm
Cold
respectively.
Default
select
?
Hot
(Hot&Cold)
adjust the water level as required. The appropriate
of detergent is shown next to the water level in
the WATER-DETERGENT diagram
Use to
amount
setting is Cold.
?
Water level is
automatically selected for fuzzy (normal)
program.
The following
settings are indicated
EX-LARGE
pushed LARGE
HOT
COLD
?
Use it to
button(option)
adjust the strength
of
EX-LARGE
LARGE
MEDIUM
SMALL
NORMAL
water current
?
Power
option
selections
light up
Delay Start (Reservation)
The time increases when the button is
?
The
in sequence as follows
NORMAL→STRONG→
GENTLE→NORMAL
?
delayed finishing time.
Use to set
?
following settings are indicated as the
buttonispushed3→4→5→...11→12→
14→16→ ...46→48→3HOUR.
?
To cancel
Adjustment can be made while
washing
(refer
to
delay time,
16p)
Note
*
The control
?
pushed.
panel may differ according to
different models
turn
the power switch off.
DELAY
HOUR
TIME
LEFT
MIN.
Process button
button
?
a
SMALL
WATER.DETERGENT
STRONG
GENTLE
Wash power
the button is
LARGE
MEDIUM
WARM
as
Use to select SOAK,
WASH, RINSE and
SPIN functions
desired.
as
W
13
Start/ Pause button
left, Delay Start (Reservation), Alarm indication
Time
?
?
?
Time left
Delay
During operation,
the
remaining time is indicated.
Start indication
program
?
-
(Reservation) When delay start (reservation)
is selected, it indicates the finishing time. (RES.=DELAY)
-
Alarm indication -When
indicate the
abnormality.
?
?
an error
For
occurs,
example,
an error
message appears to
indicates that the lid is
HOUR
MIN.
pause the
The power goes off
automatically 10 minutes
stopping.
AUTO OFF
(Power) button
AUTO OFF
FUZZY 3
ECONOMY
JEAN
WOOL 3
or
washing process.
Repeats start and pause by
pushing the button.
after
open.
SOAK
WASH
RINSE
SPIN
Use to start
?
START
PAUSE
?
?
Use to turn the power
off.
Push
again
on or
off
on or
and power goes
The power goes off
automatically about 10
seconds after the wash is
finished.
Child lock function
Use to lock
Program
unlock the control
or
settings from
being changed by a child.
To lock, push the PROCESS and
buttons to prevent
PROGRAM buttons
simultaneously and to unlock
push them one more time during
the washing process.
(refer
※
:
to p
?
?
?
button
Use for
selecting wash program.
This button allows you to select 4 different programs
for different kinds of laundry and dirtiness.
program selections light up in sequence
FUZZY (NORMAL)
ECONOMY
WOOL
program
FUZZY
(NORMAL)
by pressing
etc.
as
follows:
JEAN
Select the desired
the button.
18)
3 step works at
large and medium water level of Fuzzy and Jean course.
BeforStaingWsh
14
Washing Programs
WashingProm
AUTO OFF
Add
the
Washing
Programs
Add
the detergent
laundry
Fuzzy Washing
1
(Normal Wash)
2
4
Used for normal loads, this mode
automatically selects the most
・Add the appropriate
quantity of detergent as
indicated by the water
level next to WATER-
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly
DETERGENT.
Or follow the
detergent
manufacturer's
・The p
secon
laund
・Then t
the am
be use
water
instructions
Economy Wash
washing lightly
3
1
5
2
Use this mode when
solided clothes for
a
・Select the
short time. The
weight should be under
ECONOMY
2.0kg.
program on
the Control
panel.
Jean Wash
Use Jean program when
Jeans of different sizes
washing
・Spread the
jean
evenly in
the tub
Wool Wash
as
3
1
Use this program for washing delicate
fabrics such
5
2
3
1
・Select the Jean
program on the
Control panel.
5
2
lingerie and woolens.
・Use neutral
(wash only "water washable" clothes)
Before washing your woolens check
the care label for the washing
laundry.
WOOL
instructions.
program on
the Control
(wash only water washable clothes)
panel.
4
1
Soak Wash
Use this mode for washing
excessively dirty laundry by soaking
in water for
some
time to
simultaneously except for 'WOOL'
program.
3
2
6
not work in
WOOL
remove
washing programs
・When washing
woolens use a mild
detergent recommended for washing wool.
・SOAK will
Program.
proteins and fats. 'SOAK' mode can
be used with all
detergent
appropriate for the
・Select the
・Keep pressing the PROCESS button
RINSE,
SPIN
lights
are on
until the SOAK
simultaneously.
washing process from
・If necessary, select the desired
(SOAK+WASH+RINSE+SPIN), (SOAK+WASH+RINSE),
(SOAK+WASH) manually.
・The w
light is on and then WASH,
amou
SOAK
WASH
RINSE
SPIN
used w
water
15
Close the lid
3
Finish
Caution & Note
6
5
・If water is already in the tub,
or
putting wet
laundry into the tub before starting will
increase the water level.
・The pulsator rotates for 8
seconds to detect the
laundry load.
・Then the water level and
the amount of detergent to
be used will be shown and
water will be supplied.
4
4
4
・Water will be
supplied
for 2 minutes after the
start of the wash to
supplement the water
the laundry has
absorbed.
6
・When the wash
program ends, the
buzzer will ring for
10 seconds before
the Power goes off
automatically.
・With
lightweight bulky loads, water level can
be set low.
・Changes to water temperature (hot/cold) and
wash level are possible during operation.
(refer to p 12)
7
6
7
6
7
・When
setting the water level manually, do not
set to MEDIUM to
prevent damage to laundry.
・Washing with hot water may damage the
laundry (Water is set to cold automatically).
Ensure that the load is under 2kg
・In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing may still
contain
5
・The water level and the
amount of detergent to be
used will be shown and
water will be supplied.
7
8
some
water. This is normal.
・Soak Wash cannot be selected for the Wool
Wash program.
WashingProm
16
D
AditonalFucOps
1
elay Start (Reservation) Wash
Delay
Start (Reservation) Wash is used to
The hours to be
The time on the
delay the finishing time of the
be
set
the
user
delayed
by
accordingly.
display is the finishing time not the start time.
operation.
can
,
Press the POWER button to turn power
on.
AUTO OFF
2
Press the PROGRAM button to select the
washing
program.
Select the program for laundry on the Control
This program will not work in Wool Program.
3
Press the DELAY START
is to be
delayed washing
How to set the
to set
the time when the
completed.
delay time.
DELAY
you'd like your wash to finish at 9
a.m. set the time as in the figure below.
4
When you push the button the reservation time changes 3
14
5 →...12
16 →...→ 48
3 repeatedly.
Example
:
It's 7
(Reservation) button
a.m. now.
If
→
→
4
Add the
panel.
→
detergent.
→
The
HOUR
TIME
LEFT
MIN.
→
(RES.=DELAY)
appropriate quantity of detergent marked next to the
water level
of WATER-DETERGENT.
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid
5
Add the
laundry
and press the START/PAUSE button.
When you press the START/PAUSE button the
blink.
6
an
Close the lid.
Water will be
Finish
The
wash to
light will
supplied for 2 minutes after the start of the
supplement the water the laundry has absorbed.
washing will be finished according to the delayed time.
Note
If the lid is open, the machine will not work, and
To select
washing program, spinning time,
(RESERVATION)
an
alarm
water level
button and select the desired
or
option.
signal will
alarm to remind you to close the lid.
hot/cold manually, press the DELAY START
Then press the START/PAUSE button.
laundry cannot be taken out immediately after the wash program ends, it is better to
spinning program (The laundry will be wrinkled if left for a long time after spinning.)
When the
.
omit the
17
Option
Washing
When you
only
need the Wash, Wash/Rinse
or
Rinse
cycles,
these
can
be set
manually
1
Press the AUTO OFF (Power) button to turn power
AditonalFucOps
on.
AUTO OFF
2
Wash
,
Wash+Rinse
Rinse
,
Rinse+Spin
,
,
Press the PROCESS button until above
light is on. (refer to p13)
When you want to
washing tub drains
Spin only options
Option Washing
only drain, wait until the water in
completely and then, turn off the
the
power.
3
Press the WATER LEVEL
level
of
laundry.
automatically.
amount
button,
Add the
5
Press the START/PAUSE button.
6
Add the
into the
detergent
control the
water
anything,
level
according
to
the
it is set the LARGE water
(refer
4
laundry
to
If you do not choose
to
p12)
tub.
washing
and close the lid.
Note
?
Wash, Wash/Rinse or Rinse only option is selected, the water will not be drained off after the wash
completed. If you wish to drain the water, press the SPIN button and wait until the water in the tub has drained
completely. Then press the START/PAUSE button
When
a
is
.
?
?
If you do not
If
specify the water level,
then Medium will be
only Rinse is selected, the process will
start
from Water
automatically selected.
Supply.
18
O
AditonalFucOps
ther Useful Functions
Child Lock Function
If you want to lock all the
child lock
keys to prevent settings from being changed by a child,
you
can use
the
option.
How to Lock
1
2
Press the POWER button.
AUTO OFF
Turn Power
Press the START/PAUSE button to start
washing.
After all
3
on.
washing conditions
are
set
Press both the PROCESS button and the PROGRAM button
according to
the manual.
simultaneously.
During the wash program, all the buttons are locked
until washing is completed or until the child- lock
function is deactivated
"
"
and the
manually.
remaining time will be displayed
alternately in child-lock mode.
How to Unlock
If you want to unlock
during wash, press both the PROCESS
and the PROGRAM button
simultaneously
again.
Auto Restart
Although the machine will not work during a power failure or if power is interrupted, when power is resumed,
it will start again automatically from the point in the cycle when it stopped
※
Mute
Applied
models
:
WF-T5001(~5)PD(E/F),T5011(~5)PD(E/F),T5021(~5)PD(E/F)
WF-T5501(~5)TD(E/F),T5511(~5)TD(E/F),T5521(~5)TD(E/F)
WF-T6001(~5)TD(E/F),T6011(~5)TD(E/F),T6021(~5)TD(E/F)
WF-T7001(~9)PD(E/F),T7011(~9)TD(E/F)
WF-T8011(~9)TD(E/F),T8011(~9)TD(E/F)
Option
If you want to
use
the
washing machine without alarm signal sounds, press both the
WATER LEVEL and
PROCESS buttons simultaneously.
To make buzzer
time.
work, press both the WATER LEVEL and PROCESS buttons simultaneously
one more
19
and
Placing
Leveling
Please ensure that transit restraint has been removed before op
1
Place the machine
on a
erating your machine.
flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2 cm to the
right side and left sides of the machine for ease of
than 10
cm
more
installation.
At the rear,
more
a
minimum clearance of 10
cm
is
than
2cm
suggested.
more
than
2cm
2
Check that the machine is level
Open the lid and look from above to
same as
3
see
Top
view of the machine
if it is
shown.
Leveling
the machine
Lift the front of the
washing machine and twist
Adjustable Leg
washing machine is
placed evenly.
until the
the
Adjustable legs
※
Installing the Anti-Rat Cover (option)
The anti-rat cover should be affixed
firmly from the back of the washer
UP
Caution
If the power is supplied from a cord extension set or generator, the cord extension set or electrical
portable outlet device should be positioned so that it is not exposed to splashing or ingress of moisture.
Instal ion
20C
Instal ion
onnecting
Supply
Hose
Before connecting the Water Supply Hose to the water tap, check the hose type and
then choose the correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country, Make
sure to connect the blue inlet hose to the cold water tap, and the orange inlet hose to
the hot water tap.
Connecting
Water
Normal
1
Water
Supply
Hose to water
Type
Untighten
tap
(Normal tap without thread &
the
screw
type inlet hose.)
Rubber
screw
packing
Untighten the screw of the connector so that the
tap can be placed in the middle.
2
Fixing the
connector to
screw
Connector
the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
3
Attach the
water
hose
supply
securely
to
the
connector
Push the water
supply hose vertically upwards
that the rubber seal within the hose
completely
to the
can
Connector
so
adhere
Water
tap.
Supply
4
Fixing the
connector to
the
water
supply
hose
Attach the water
then
5
supply hose to the connector and
tighten it by screwing it to the right.
Check the connection of
After
water
supply
connecting the hose, open the tap to check
for any water leakage.
If the water leaks, close the tap and start again
from step 1
hose and the
connector
Hose
21
Normal
1
Type
(Normal tap without thread &
Separate Middle
connector
one
from Water
touch type inlet hose.)
Supply
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
Hose
Middle
Fixed Sticker
connector
Pressing
Handle
Pressing
Rod
Water
2
Loosen the fixed nuts to connect the connector to the
Untighten
tap
can
be
the
screw
of the connector
Hose
tap
that the
so
Supply
Rubber
placed in the middle.
packing
screw
Fixed sticker
Note
In
case
tap is
too
Guide
large.
plate
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate.
3
Then follow
Fixing
Rubber
packing
step1.
Connectors to the
Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4
4
screws.
Connector and Middle Connector
Fixing Upper
Remove the fixed sticker in between the
and Middle Connectors.
by holding
one
5
Tighten the connectors
connector and
connector to the
Connector
Upper
Middle
twist middle
Connector
Fixed sticker
right.
Connecting Middle
Connector and Water
Supply
pressing rod of the Water Supply
separated from middle connector
Step1) and then join it to the middle
Connector
Middle
Connector
Hose
Press down the
Hose which
(refer to
was
Pressing
rod
connector.
Water
6
Check for
After
water
connecting
the
leakage
hose, open the tap
to check
for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
If you
skip step 1,
water
leakage may
occur.
Supply
Hose
Pressing
handle
Instal ion
22
C
Instal ion
Screw
1
Water
onnecting
Hose
Type
Attach the
water
Push the water
packing
Supply
supply
supply hose up
within the hose
can
so
hose
to
the tap.
that the rubber
adhere
completely to
the tap.
Water
tap
Rubber
Water
2
Connect the water
Connect the
tighten
3
it by
Check
After
supply
hose
supply hose to the tap
screwing it to the right.
water
water
to
Packing
Supply
the tap.
and then
leakage.
the
hose,
connecting
leakage.
open the tap to check
for any water
Connecting
?
Water
Connect the
the
Supply
water
Hose to the machine
supply hose to
inlet valve of
and then lock it
washing machine,
connecting part.
by turning
the hose
?
Check
to
see
if there is
a
rubber seal inside the
Hose connector
connector.
Rubber seal
Hose
23
Connecting
Before
Drain Hose
connecting
Drain Hose, check your Drain Hose model and choose the correct
instructions.
Instal ion
Pump Model
1
Fit the end of the drain hose to the outlet of the
2
Put the other end of the drain hose
drain pump and
tighten the clamp.
over
the
standpipe or
wash tub.
Hose
Guide
Within 50
mm
0.9~1.2m
Drain Hose
Note
To prevent siphoning, the drain hose should not extend more than 50 mm from the end of the hose
The discharge height should be approximately 0.9
1.2 m from the floor.
~
Non-Pump Model
1
Before
connecting
Ensure that the hose
clip is
set
indicated here.
as
Clip
2
Connect the Elbow Hose
Push the elbow hose toward the
washing
3
body
of the
machine.
Place the Drain Hose
change the direction of the hose, pull
change the direction.
Repeat Step 2.
To
elbow hose and
out the
guide.
24
G
CarendMitc
rounding
Method
Earth wire should be connected.
If the earth wire is not connected, there is
caused by the current leakage
possible
a
danger
of electric shock
.
Grounding
Method with Ground insert space Terminal
If the AC current outlet has
a ground terminal, then
required. Note that AC
power outlet configurations may differ from country
separate grounding is
to
not
Ground Terminal
country
Outlet with
Other
Method
Grounding
ground
terminal.
Burying Copper Plate
Connect the Ground Wire
Plate and
bury
it
more
to
a
Ground
Copper
ground.
than 75cm in the
Ground Wire
75cm
Using Ground
Connect the
Ground
Wire
ground Wire to
exclusively
Grounding.
the socket
Copper
provided
for
Using
a
Plate
Ground
Wire
Short Circuit Breaker
If grounding methods described above are not
possible, a separate circuit breaker should be
employed and installed by a qualified electrician
Short-circuit
breaker
Caution
?
?
To prevent a possible explosion, do not connect ground to a gas pipe
Do not connect ground to telephone wires or lightning rods. This may be
storms
?
?
Connecting ground to plastic has no
effect
Ground wires should be connected when
an
extension cord is used.
dangerous during electrical
25
Cleaning
Cold water
?
If you
and maintenance
washing
always use cold water,
we
recommend that
intervals e.g. every 5th wash should be at least
a warm or
hot wash be used at
a
regular
a warm one
When you have finished
?
?
Turn off taps to prevent the chance of flooding should
Always unplug the power cord after use.
a
hose burst.
When water supply into the tub is not clean or the filter is clogged with particles
filter in the inlet valve occasionally.
(The figure of power cord and water tap may vary according to the country)
(such
as
sand),
clean the
To Clean the Filter in the Inlet Valve
Close the tap before turning off the power.
Select both hot/cold and then press the
1
Turn off the power before
2
pulling out the cord.
[START/PAUSE] button to remove water
completely.
from the machine
After
3
removing the water supply
pull out the filter.
hose
Then
use a
4
Replace the filter after cleaning it.
brush to clean the filter.
Caution
Before
cleaning the filter,
the
impurities in the water supply hose should be removed.
To Clean the Lint Filter
1
Pull out the lint filter from
2
Turn the net inside out
the tub in the direction
to clean the filter and
shown below.
rinse it with water.
3
Replace- the filter to the
original location. Push the
lip of the filter until a pop
sound is heard.
Note
?
If the lint filter is torn
To Clean the
1
damaged, purchase a new
one
from LG service center.
Pump casing (for pump model)
Unfasten 2
back
or
screws
of the
cover.
2
Turn the cap as shown in
diagram and unfasten it.
Remove
as
foreign objects
pin, button, coin,
3
fasten it.
such
etc
(Bottom view)
(Bottom view)
Caution
?
Check if water leaks after
reassembling. (The
Reassemble the cap to
the arrow direction and
Rubber
ring
is in the
cap)
CarendMitc
26
C
CarendMitc
and Maintenance
leaning
When there is
a
fear of
freezing
?
Close the
?
Remove the water which remains in the water
?
Lower the drain hose and drain the water in the bowl and the drain hose
water
taps and
remove
the Water
Supply Hose.
supply.
by spinning.
If frozen
?
?
?
supply hose, and immerse it in hot water at approx.. 40˚C.
Pour approx.. 2 liters of hot water at approx.. 40˚C, into the bowl and let it stand for 10 minutes.
Connect the water supply hose to the water tap and confirm that the washing machine performs the
Remove the water
supply
and
Wash Inner-tub
drainage of water.
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
use a clean soft cloth dampened with liquid detergent, then rinse. (Do
the inner-tub
not use harsh or
Inlet Hoses
Hoses
connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
sharp objects.
Exterior
Long
gritty cleaners.)
Vacations
Be
sure
water
be below
supply
freezing.
surface with
is shut off at faucets. Drain all water from hoses if weather will
Scrud
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into
with detergent. This build-up is not brought about by a fault in the machine. If scrud is allowed to build-up
in the machine it can result in stains on your clothes or an unpleasant smell in your washer.If you wish to use
contact
fabric softener
we
If you wish to
fabric softener
use
recommend.
we
recommend:
?
Clean your machine regularly
Cold water washing increases the chance of this
intervals e.g. approx. every 5th wash.
?
Fabric softener of thinner
?
Cleaning
?
?
?
?
?
?
?
?
?
?
consistency is less likely to leave residue on the dispenser and contribute to a build-up.
the inside of your
If you use fabric softener or do
the inside of your machine.
washing
machine
regular cold water washing,
Fill your machine with hot water. Add about two cups of
Select Wash
Stop
the
After
cycle
machine,
soaking,
and operate.
Repeat it 2 or 3 times.
open the
and leave it to soak
lid,
drain the machine and
run
important that you occasionally clean
powder detergent that contains phosphate.
overnight.
through a regular cycle.
during this procedure.
might damage your washing
Concentrated bleaches and
a
it is
the machine
We do not recommend that you wash clothes
Products that
?
build-up occurring. We recommend a warm or hot wash at regular
machine
diaper sanitizer will cause damage to the paintwork and components of your washer.
Hydrocarbon
petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint (Be careful
when washing garments stained with these solvents as they are flammable DO NOT put them in washer or dryer.)
solvents i.e.
Some pretreatment sprays
or
liquids can damage your washer's control panel.
Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine but we
suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in your washer.
Do not use your washer lid
as a
work surface.
27
Troubleshooting
Look for your problem below, then check the things we suggest. More often
than not, this will give you the answer to your problem. And you'll be able to
carry on without having to telephone your service center.
WASH PROBLEM
Symptom
residue
clothes
Lint
on
or
Error
Check up
Message
Incorrect
sorting
Washing
too
long
?
?
Separate lint producers from lint collectors.
Wash small loads for
a
shorter time than
larger
loads.
Natural By-product
When Washing
Certain Items
Detergent
on
clothes
Black spots
clothes
on
Detergent
dissolving
not
Incorrect use of
fabric softener
?
any lint not removed
Use
warmer
water
Using the dryer should remove
by the washer.
temperature.
Try pre-dissolving the detergent in warm water
Try a liquid detergent.
?
?
?
Dye transfer
Some lint is normal.
?
When
filling dispenser,
Sort whites
or
splash or overfill.
directly on clothes.
do not
Never pour fabric softener
Pre-treat stain and rewash.
lightly colored items from dark
colors.
-
Not enough
detergent used
?
dry non-colorfast clothes separately
Wash and
Insufficient
detergent,
clothes,
result in black marks
can
for the amount of soil
on
on
the
clothes
A
build-up caused
by the interaction
?
of fabric softener
and detergent can
flake off and marks
on clothes.
Fabric
damage
(Snags, holes,
rips or
tears,
excessive wear)
Pins, snaps,
hooks, sharp
buttons, belt
buckles, zippers,
?
?
Cleaning the inside of your washing machine
(refer to p25, p26)
Fasten snaps, hooks, buttons, and zippers.
Remove any loose brassiere wires.
Remove
?
Turn knits
and sharp objects
left in pockets
Chemical Damage
a. Chlorine Bleach
b. Battery Acid
c.
Hydrogen
Peroxide
objects in pockets and sharp buttons.
(which snag easily) inside out.
?
?
Dilute bleach
?
Use caution around
products
tears
-
or use
these
in fabrics.
dispenser (See User's Guide)
battery acids, skin and hair care
the
can remove
color and
cause
holes
or
Troubleshting
28
T roubleshooting
Troubleshting
Symptom
Error
Message
Non-chemical
Damage
a. Age &
Check up
?
?
Normal Use
b. Poor Construction
c.
Check construction
Mend any
carefully when purchasing
damage
laundering
before
Overloading
d. Mice & Inserts
e.
The
laundry
comes out dirty
Sunlight
Water temperature
is too cold.
?
Water temperature
is not correct
?
?
Use
warmer
water
temperature
according to soil type.
example, blood and mud are better washed in
cold water, while oily soils wash better in warmer
Select the wash temperature
For
water.
Stain is not pretreated
?
Incorrect
sorting
?
?
little
Did you load too much into the machine?
White clothes
better washed
separately.
Separate light
heavily soiled items, as clothes
can pick up soil from dirty wash water.
Loads made up of articles of varying sizes will
wash better (e.g. full loads of sheets may not wash
are
and
?
Insufficient
a
stains like collars and cuffs to
?
Washer is
overloaded
detergent dissolved in water onto
help shift dirt.
Wash stains as soon as possible. The longer they are
left the harder they are to remove.
Brush
?
that
well).
Not
enough detergent for load size or amount of
water requires more detergent than soft
soil. Hard
detergent
water.
Pilling
Result of normal
wear on
poly-
cotton blends and
fuzzy
Grayed or
yellowed
clothes
?
While this is
can
slow the
not caused
by the washer, you
pilling process by washing
garments inside
out.
fabrics
Not
enough
detergent
Use
Water is not hot
Make
more
detergent (especially with larger loads).
sure
water heater
enough
120F~40F.(48˚C
Washer is
overloaded
Select load size
Dye transfer
Sort clothes
is
delivering water at
60˚C.).
~
to match clothes
load.
by color. If fabric label states wash
separately,unstable dyes may be indicated.
29
Before
calling
for service, check the
Symptom
Water
Supply
Failure
Error
problem against the
list bellows.
Message
Check up
.
.
.
.
Is the water tap shut off?
Is the water supply cut off ?
Is the tap
or
water
supply hose frozen ?
Is the water pressure low or is the filter of the inlet
clogged with impurities?
valve
.
.
Drainage Failure
Spin Failure
Door(Lid) Open
Internal sensing
failure
Power failure
Overflow failure
Is the Hot hose connected to cold?
Is the Cold hose connected to Hot?
.
Is the drain hose
.
Is the drain hose bent
.
Is the internal part of the hose or drain pump
(only pump model) clogged with impurities?
.
Check if electric power has gone off.
positioned correctly?
or placed too high?
.
Is the
laundry evenly balanced?
.
Is the
washing machine placed on
.
Is the lid closed?
.
a
flat surface?
Please call your nearest LG Electronics service center
for help.
Troubleshting
30
T
erms
of
Warranty
What Is Not Covered:
?
If the
?
product is
If the fault is
?
If the fault is
connected to any
voltage other than that shown on the rating plate.
caused by accident, neglect, misuse or Act of God.
caused by factors other than normal domestic use or use in
accordance with the owner's manual.
?
?
?
?
?
?
?
?
?
Provide instruction
change the set-up of the product.
If the fault is caused by pests for example, rats or cockroaches etc..
Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
Correcting the installation for example, levelling the product, adjustment of drain.
Normal maintenance which recommended by the owner's manual.
Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
Replace fuses in or correct house wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects
with this appliance.
If the
on use
of product
or
product is installed outside the normal service area, any cost of transportation
involved in the repair of the product, or the replacement of a defective part, shall be
borne by the owner.
31
Specification
Specifaton
H
D
W
Model
WF-T5001(~5)PP(H,C,D,E,F)/ T5011(~5)PP(H,C,D,E,F)/ T5021(~5)PP(H,C,D,E,F)
WF-T5501(~5)TP(H,C,D,E,F)/ T5511(~5)TP(H,C,D,E,F)/ T5521(~5)TP(H,C,D,E,F)
WF-T6001(~5)TP(H,C,D,E,F)/ T6011(~5)TP(H,C,D,E,F)/ T6021(~5)TP(H,C,D,E,F)
WF-T7001(~9)PP(H,C,D,E,F)/ T7011(~9)PP(H,C,D,E,F)/ T7008TH
WF-T8001(~9)TP(H,C,D,E,F)/ T8011(~9)TP(H,C,D,E,F)
540(W)
Size
x
540(D)
x
850(H) WF-T5001(~5),T5201(~5),T5501(~5),T5521(~5),
WF-T6001(~5),T6021(~5)
Water tab pressure
※ In
our
to the
540(W)
x
540(D)
x
890(H) WF-T5011(~5),T5511(~5),T6011(~5)
590(W)
x
606(D)
x
928(H) WF-T7001(~9),T8001(~9)
590(W)
x
606(D)
x
958(H) WF-T7011(~9),T8011(~9)
30
-
800 kPa (0.3 -8.0
kgf /cm2 )
continuing effort to improve the quality of our appliances,
appliance without revising this manual.
it may be necessary to make
changes
P/No.: 3828EA3007N
Download PDF