LG | 21FC1RB | LG 21FB7AG Owner’s Manual

Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number
Serial number
:
:
P/NO : MFL39582005 (MC059B, 124D TX)
Contents
Installation.........................................................2
Connection of external equipment..................3
Location and function of controls...................4
Basic operation.................................................8
On screen menus..............................................8
Setting up TV stations......................................9
Picture adjustment..........................................12
Sound adjustment...........................................13
Time setting.....................................................15
Other functions...............................................16
Troubleshooting check list............................19
Installation
Power
Aerial
This set operates on an AC mains supply, the
voltage is as indicated on the label on the back
cover. Never apply DC power to the set. In the
event of thunderstorms or powercuts, please pull
out the aerial and mains plugs.
Connect the aerial cable to the socket marked
+75 Ω on the back cover. For the best reception
an outdoor aerial should be used.
Warning
Position your set so that no bright light or sunlight
falls directly onto the screen. Care should be
taken not to expose the set to any unnecessary
vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow
of air. Do not cover the ventilation openings on
the back cover.
To prevent fire or shock hazard, do not expose
the set to rain or moisture.
Do not place anything containing liquid on top of
the set, this may cause a fire or could give an
electric shock.
Service
Never remove the back cover of the set as this
can expose you to very high voltage and other
hazards. If the set does not operate properly,
unplug it and call your dealer.
2
Location
Connection of external equipment
You can connect additional equipment, such as
VCRs, camcorders etc. to your set.
Here shown may be somewhat different from your
set.
Aerial socket
1. Connect the RF out socket of the VCR to the
aerial socket on the back of the set.
2. Connect the aerial cable to the RF aerial in
socket of the VCR.
3. Store the VCR channel on the programme
number 0 using the ‘Manual programme tuning’ section.
4. Select the programme number where the VCR
channel is stored.
5. Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1. Connect the audio/video out sockets of the
VCR to audio/video in sockets of the set and
in sockets of the VCR to out sockets of the set.
2. If the VCR is connected to the AV sockets on
the set, press the TV/AV button to select AV
(or AV1), AV 2.
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the
screen.
You can also record programmes received by
the TV on video tape via audio/video out sockets.
Note : If you have a mono VCR, connect the audio
cable from the VCR to the AUDIO L/MONO socket of the set.
Euro scart socket (option)
1. Connect the Euro scart socket of the VCR to
the Euro scart socket of the set.
2. Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when
connected to Euro scart socket, the set will
switch to AV (or AV1) mode automatically. But
if you want to keep on watching TV mode,
press the D / E or NUMBER buttons.
Otherwise press the TV/AV button on the
remote control handset to select AV (or AV1).
The VCR playback picture appears on the
screen.
You can also record programmes received by
the TV on video tape.
Note : Signal type RGB, i.e. the signals red, green
and blue can only be selected for the Euro scart
socket. These signals are transmitted, for example, by a pay TV decoder, game machine or photo
CD unit, etc.
S-video / Audio in sockets (S-AV)
(option)
When connecting the S-video socket of the VCR
to the S-VIDEO socket of the set, the picture quality will be further improved.
1. Connect the S-video socket of the VCR to the
S-VIDEO socket of the set.
2. Connect the audio cable from the VCR to the
AUDIO sockets of the set.
3. Select AV3 by pressing the TV/AV button
repeatedly.
4. Press the PLAY button on the VCR.
The VCR playback picture appears on the
screen.
Note : If both S-VIDEO and VIDEO sockets have
been connected to the VCR simultaneously, only
the S-VIDEO can be received.
Component in sockets (option)
1. Connect the COMPONENT video output sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the DVD
player to the COMPONENT INPUT sockets (Y
PB PR) on the set.
2. Connect the audio cable from the DVD player
to AUDIO IN sockets of AV (or AV1).
3. Press the TV/AV button to select COMPONENT.
4. Press the PLAY button on the DVD player.
The COMPONENT playback picture appears
on the screen.
Headphone socket (option)
Only models which have a headphone socket can
perform this function.
Insert the headphone plug to the headphone socket of the set.
You can listen to the sound through the headphones. To adjust the headphone volume, press
the F / G button.
If you press the MUTE button, the sound from the
headphone’s is switched off.
3
Location and function of controls
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
Remote control handset
Before you use the remote control handset, please install the batteries. See the next page.
POWER
MUTE
1. POWER
switches the set on from standby or off to standby.
1
1
2
3
4
5
6
7
8
9
MENU
0
TV/AV
2
3
4
5
EYE/
PR
VOL
I / II /
( )
VOL
OK
PR
( )
Q.VIE
LIST
W
6
PSM
SSM/
SLEEP
7
FAVOURITE
/
8
PICTURE
SOUND
2. NUMBER BUTTONS
switches the set on from standby or directly select a number.
3. MENU
selects a menu.
4. EYE/ (option)
switches the eye function on or off.
*
5.
( )/
( ) (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
scans programmes automatically.
F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the current mode.
6. Q.VIEW
returns to the previously viewed programme.
TURBO/
9
7. PSM (Picture Status Memory)
recalls your preferred picture setting.
8. FAVOURITE
selects a favorite programme.
9. TURBO PICTURE / SOUND BUTTON (option)
selects Turbo picture and sound.
4
Location and function of controls
10. MUTE
switches the sound on or off.
11. TV/AV
selects TV or AV mode.
switches the set on from standby.
12. I/II/ (option)
selects the language during dual language broadcast. (option)
selects the sound output.
*
13. LIST
displays the programme table.
14. SLEEP
sets the sleep timer.
15. SSM/ (Sound Status Memory) (option)
recalls your preferred sound setting.
*
POWER
MUTE
10
1
2
3
4
5
6
7
8
9
MENU
0
TV/AV
º/ ) (option)
16. SURROUND (º
selects surround sound.
11
*
* : No function
COLOURED BUTTONS : These buttons are used for teletext (only
TELETEXT models) or programme edit.
EYE/
PR
VOL
The remote control handset is powered by two AAA type batteries.
To load the batteries, turn the remote control handset over and
open the battery compartment. Install two batteries as indicated by
the polarity symbols ( + and - ) marked inside the compartment.
12
VOL
OK
PR
Battery installation
I / II /
( )
( )
Q.VIE
LIST
W
13
PSM
SSM/
SLEEP
FAVOURITE
/
PICTURE
SOUND
14
15
16
TURBO/
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
5
Location and function of controls
Front panel
21FX6 series
21FD1/4 series
3
8
AV2
VIDEO
MENU
L/MONO AUDIO R
6
OK
PR
VOL
2
1
2 3
4
5
7
21FX4 series
1
4
5
15/21FC2 series
AV2
1 2 3 4
5
8
21FB2 series
VIDEO
6
L/MONO AUDIO
R
7
1
R AUDIO
PR
4 5
2 3
5
8
1 2 3 4
OK
MENU
4
21FG1 series
VOL
VIDEO
PR
5
L AUDIO R
21FJ4 series
ON/OFF
AV
L/MONO
6
VOL
OK
21FB5 series
7
2 3
1
MENU
ON/OFF
VIDEO
1
2 3 4
8
6 7
5
AV2
21FB3 series
ON/OFF
MENU OK
VOL
PR
AV
VIDEO AUDIO
VIDEO L/MONO AUDIO R
MENU
ON/OFF
OK
VOL
PR
AV3
7
1
AUDIO
5
6 7
1
6 7
2 3
4
5
21FC9/21FD6 series
17/21FB7 series
VIDEO
6
2 3 4
4
5
AV
MENU
OK
PR
VOL
ON/OFF
1
23
4
3
1
5
PR
VIDEO
7
6
17/21FX5 series
VOL
L/MONO AUDIO R
6
1 2 3 4
5
2
AV
5
8
8
Location and function of controls
Front panel
21FC1 series
VIDEO
MENU
OK
PR
VOL
AUDIO
6
1
2 3
17/21FA3 series
7
4
5
AV
MENU OK
VOL
PR
ON/OFF
L/MONO
2
VIDEO
4
1 2 3
15/21Q9 series
5
L/MONO
6
MENU
VOL
SOUND
OK
PR
PICTURE
TURBO
ON/OFF
AUDIO R
7
4
1 23
AV2
7
6
8
5 9
21FE6 series
7
1 23
4
5
21Q6 series
6
TV/AV
(VOL)
VIDEO
( ) PR ( )
L/MONO AUDIO R
ON/OFF
AV2
6 7
1 2 3 101112
8
21Q4 series
7
MENU
ON/OFF
VOL
VOL
PR
OK
1. MAIN POWER (ON/OFF)
switches the set on or off.
2. POWER/STANDBY INDICATOR
illuminates brightly when the set is in
standby mode.
dims when the set is switched on.
3. REMOTE CONTROL SENSOR
Note : Only use the supplied remote
control handset. (When you use others, they’ll be not able to function.)
4. MENU (option)
selects a menu.
5. OK (option)
accepts your selection or displays the
current mode.
F / G (Volume Up/Down) (option)
adjusts the volume.
adjusts menu settings.
D / E (Programme Up/Down) (option)
selects a programme or a menu item.
switches the set on from standby.
6. AUDIO (or AUDIO-L/R)/VIDEO IN
SOCKETS (AV or AV2) (option)
Connect the audio/video out sockets of
external equipment to these sockets.
7. HEADPHONE SOCKET (option)
Connect the headphone plug to this
socket.
8. EYE (option)
adjusts picture according to the surrounding conditions.
9. TURBO SOUND / PICTURE (option)
VIDEO
switches Turbo sound or Turbo picture
function on or off.
L/MONO AUDIO
6
1
4
5
23
8
10. TV/AV (option)
selects TV or AV mode.
clears the menu from the screen.
switches the set on from standby.
R
AV2
21FJ5 series
11.
1 2 3 4
5
(Function) (option)
selects volume, EYE (option), picture
items or brief auto programme while
the menus not display.
12. + / - (D / E) (option)
adjusts the function or selects a programme.
switches the set on from standby.
Note : Shown is a simplified representation of front or side panel. Here shown
may be somewhat different from your set.
7
Basic operation
On and off
Quick view
1. Press the main power button to switch the set
on.
2. If the set is in standby mode, press the
POWER, D / E, TV/AV or NUMBER buttons
on the remote control handset to switch it on
fully.
3. Press the POWER button on the remote control handset.
The set reverts to standby mode.
4. Press the main power button again to switch
the set off.
Press the Q.VIEW button to view the previous
programme you were watching.
Note : If, while the set is switched on, the mains
plug is disconnected the set will switch to standby
or power on when the mains plug is replaced in
the mains power socket.
On screen language selection (option)
Programme selection
You can select a programme number with the D /
E or NUMBER buttons.
Volume adjustment
Press the F / G button to adjust the volume.
Mute function
Press the MUTE button. The sound is switched off
and the display > appears.
You can cancel it by pressing the MUTE, F / G,
SSM/ , I/II/ , TURBO SOUND button.
* *
The menu can be displayed on the screen in
desired language. First select your language.
1. Press the MENU button and then D / E button to select the Special menu.
2. Press the G button to select Language.
3. Press the G button and then D / E button to
select your desired language.
All the on screen displays will appear in the
selected language.
Press the OK or F button to select the
Special menu.
4. Repeatedly press the MENU button to return
to normal TV viewing.
On screen menus
The dialogue between you and your set takes
place on screen with an operator menu. The buttons required for the operating steps are also displayed.
Menu selection
1. Press the MENU button and then D / E button to
display each menu.
2. Press the G button and then D / E button to
select a menu item.
3. Press the G button to display the sub menu or
the pull-down menu.
4. Change the setting of an item in the sub or
pull-down menu with F / G or D / E.
You can move to the higher level menu with
OK or F button and to move to the lower level
menu press the G button.
8
Note :
a. In mono models, the Sound menu does not
appear.
b. In some models, Turbo Pic. will not display in
the Picture menu.
c. In some models, Turbo.Snd., AVL, Balance,
Woofer, X-WAVE or Treble, Bass will not display in the Sound menu.
d. In some models, Language, Blue back,
Game, Booster will not display in the Special
menu.
Setting up TV stations
Up to 100 TV stations can be stored by programme
numbers (0 to 99). Once you have preset the stations, you will be able to use the D / E or NUMBER
buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual
modes.
Note : In some models up to 200 TV stations can
be stored.
Auto programme tuning
All stations that can be received are stored by this
method. It is recommended that you use auto programme during installation of this set.
1. Press the MENU button to select the Station
menu.
2. Press the G button and then D / E button to
select Auto prog..
3. Press the G button to display the Auto prog.
menu.
System
Storage
Normal
Turbo
{
{
{
{
BG
I
DK
M
(O} {OOKOMENU
)
i
4. Press the G button. Select a TV system with
the D / E button on the System pull-down
menu;
BG : (Asia/New Zealand/M.East/Africa
/Australia)
I
: (Hong Kong/South Africa)
DK : (East Europe/China/Africa/CIS)
M : (USA/Korea/Philippines) (option)
5. Press the OK or F button.
6. Press the D / E button to select Storage.
7. Press the G button. Select the beginning programme number with the F / G button or
NUMBER buttons on the Storage from pulldown menu. Any number under 10 is entered
with a numeric ‘0’ (or ‘00’) in front of it, i.e.
‘05’ (or ‘005’) for 5.
8. Press the OK button.
9. Press the D / E button to select Normal or
Turbo.
Option: In some models, you can only select
Start.
Note :
a. Turbo is faster than Normal and in some
models, these searches will automatically
store all receivable stations.
b. If the programmed station has poor quality
sound, select the system again in the
Manual menu.
10. Press the G button to begin auto programming.
All receivable stations are stored.
To stop auto programming, press the MENU
button.
When auto programming is completed, the
Prog. edit menu appears on the screen. See
the ‘Programme edit’ section to edit the stored
programme.
11. Repeatedly press the MENU button to return
to normal TV viewing.
Auto programme scan
To automatically scan the pictures of stored proE
grammes, press theD( D
D ) or E( E ) button for
about 3 seconds. The picture of stored programmes appears on the screen one by one.
To stop auto programme scanning, press any button except VCR buttons.
Manual programme tuning
Manual programme lets you manually tune and
arrange the stations in whatever order you desire.
Also you can assign a station name with five characters to each programme number.
1. Press the MENU button to select the Station
menu.
2. Press the G button and then D / E button to
select Manual.
3. Press the G button to display the Manual
menu.
4. Press the D / E button to select Storage.
5. Press the G button to select the programme
number. Select the desired programme number (0 to 99) with the F / G button or NUMBER
buttons on the Storage pull-down menu. Any
number under 10 is entered with a numeric ‘0’
(or ‘00’) in front of it, i.e. ‘05’ (or ‘005’) for 5.
6. Press the OK button.
7. Press the D / E button to select System.
8. Press the G button. Select a TV system with
the D / E button on the System pull-down
menu;
BG : (Asia/New Zealand/M.East/Africa
/Australia)
I
: (Hong Kong/South Africa)
DK : (East Europe/China/Africa/CIS)
M : (USA/Korea/Philippines) (option)
9. Press the OK or F button.
10. Press the D / E button to select Channel.
11. Press the G button. Press the D / E button to
select V/UHF or Cable on the Channel
pull-down menu.
If possible, select the channel number directly with the number buttons. Any number under
10 is entered with a numeric ‘0’ (or ‘00’) in
front of it, i.e. ‘05’ (or ‘005’) for 5.
12. Press the OK or F button.
13. Press the D / E button to select Search.
14. Press the G button. Press the F / G button to
commence searching on the Search pulldown menu. If a station is found the search
will stop.
15. Press the OK button to store it. The display
Stored will appear.
16. To store another station, repeat steps 4 to 15.
17. Repeatedly press the MENU button to return
to normal TV viewing.
9
Setting up TV stations
Assigning a station name
1. Repeat the ‘Manual programme tuning’ steps
1 to 3.
2. Press the D / E button to select Name.
3. Press the G button on the Name pull-down
menu.
4. Press the D button. You can use a blank, +,
-, the numeric 0 to 9 and the alphabet A to
Z.
With the E button you can select in the
opposite direction.
5. Select the position by pressing the F / G
button and then take your choice of the second character, and so on.
6. Press the OK button.
7. Repeatedly press the MENU button to return
to normal TV viewing.
Booster (option)
In some models, Booster is an optional function. Only a set with Booster can perform this
function.
If the reception is poor at the fringe area of TV
signal, select Booster to On. When the picture
condition is good, do not select Booster to On.
1
2.
3.
4.
5.
6.
Repeat the ‘Manual programme tuning’ steps
1 to 3.
Press the D / E button to select Booster.
Press the G button.
Press the D / E button to select On or Off
on the Booster pull-down menu.
Press the OK button.
Repeatedly press the MENU button to return
to normal TV viewing.
Programme edit
This function enables you to delete or skip the
stored programmes. Also you can move some
stations to other programme numbers or insert a
blank station data into the selected programme
number.
1. Press the MENU button and then D / E button to select the Station menu.
2. Press the G button and then D / E button to
select Prog. edit.
3. Press the G button to display the Prog. edit
menu.
Deleting a programme
1. Select a programme to be deleted with the D /
E or F / G button.
2. Press the RED button twice.
10
The selected programme is deleted, all the
following programmes are shifted up one
position.
OOOOCO1DOOOO5OOSO69
O1OOCO03OOOO6OOSO17
O2OOCO12OOOO7OOSO22
O3OOSO66OOOO8OOCO09
O4OOSO67OOOO9OOCO11
DeleteOOOCopy
MoveOOOOOSkip
(O} {OOKOMENU
)
i
Copying a programme
1. Select a programme to be copied with the D / E
or F / G button.
2. Press the GREEN button.
All the following programmes are shifted
down one position.
Moving a programme
1. Select a programme to be moved with the D / E
or F / G button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with the D / E or F / G button.
4. Press the YELLOW button again to release
this function.
Skipping a programme number
1. Select a programme number to be skipped
with the D / E or F / G button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the
skipped programme. When a programme
number is skipped it means that you will be
unable to select it using the D / E button during normal TV viewing. If you want to select
the skipped programme, directly enter the
programme number with the NUMBER buttons or select it in the programme edit or table
menu.
Repeatedly press the MENU button to return to
normal TV viewing.
Setting up TV stations
This function lets you select your favourite programmes directly.
gramming or in the programme edit mode.
b. Some programmes with the channel number
shown in the programme table indicate there
is no station name assigned.
1. Press the MENU button to select the Station
menu.
2. Press the G button and then D / E button to
select Favourite.
3. Press the G button to display the Favourite
menu.
Selecting a programme in the programme
table
Select a programme with the D / E or F / G button.
Then press the OK button.
The set switches to the chosen programme number.
Favourite programme
AutoOprog.{
Manual
{
Prog.Oedit {
Favourite {
560 C0 0 5
Paging through a programme table
There are 10 (or 20) programme table pages
which contain 100 (or 200) programmes.
Pressing the D / E or F / G button repeatedly
turns the pages.
( O} {O0_9OOKOMENU
)
i
4. Press the D / E button to select -- -----.
5. Select a desired programme with the F / G
button.
6. To store another programme, repeat steps 4
to 5.
You can store up to 8 programmes.
7. Press the OK button.
8. Repeatedly press the MENU button to return
to normal TV viewing.
Press the LIST button to return to normal TV
viewing.
Repeatedly press the FAVOURITE button to
select stored favourite programmes.
Calling the programme table
You can check the programmes stored in the
memory by displaying the programme table.
Displaying programme table
Press the LIST button to display the Programme
table menu.
The programme table appears on the screen.
One programme table contains ten programmes
as below.
OOOOCO1DOOOO5OOSO69
O1OOCO03OOOO6OOSO17
O2OOCO12OOOO7OOSO22
O3OOSO66OOOO8OOCO09
O4OOSO67OOOO9OOCO11
(O} {OOKOMENU
)
i
Note :
a. You may find some blue programmes. They
have been set up to be skipped by auto pro-
11
Picture adjustment
Note: Picture menu options are not available for
RGB input source.
PSM (Picture Status Memory)
1. Press the MENU button and then D / E button to select the Picture menu.
2. Press the G button to select PSM.
3. Press the G button and then D / E button to
select a picture setting on the PSM pull-down
menu.
PSM
{
PSM
TurboOPic.{
CSM
{
Contrast {
Brightness{
Colour
{
Sharpness {
option can perform this function.
In some models, the set will automatically adjust
the picture according to the surrounding conditions. This will enable you to enjoy the most suitable picture according to the surroundings.
Press the EYE/
on or off.
* button to switch the eye function
Dynamic
Standard
Mild
Game
User
Off
(O} {OOKOMENU
)
i
4. Press the OK or F button.
5. Repeatedly press the MENU button to return
to normal TV viewing.
You can also recall a desired picture (Dynamic,
Standard, Mild, Game or User) with PSM button on the remote control. The picture Dynamic,
Standard, Mild and Game are programmed for
good picture reproduction at the factory and cannot be changed.
CSM (Colour Status Memory)
You can select the picture colour status; standard,
reddish, greenish or bluish, as you prefer.
1. Press the MENU button and then D / E button to select the Picture menu.
2. Press the G button and then D / E button to
select CSM.
3. Press the G button and then D / E button to
select Standard, Reddish, Greenish or
Bluish on the CSM pull-down menu.
4. Repeatedly press the MENU button to return
to normal TV viewing.
Picture adjustment
You can adjust picture contrast, brightness,
colour intensity, sharpness and tint (NTSC input
only) to the levels you prefer.
1. Press the MENU button and then D / E button to select the Picture menu.
2. Press the G button and then D / E button to
select Contrast, Brightness, Colour or
Sharpness.
3. Press the G button and then F / G button to
make appropriate adjustments on the each
sub menu.
4. Press the OK button to store it for the picture
user.
5. Repeatedly press the MENU button to return
to normal TV viewing.
Eye (option)
Eye is an optional function. Only a set with eye
12
When the eye function is on, the most suitable picture is automatically adjusted according to the
surrounding conditions.
At this time the display
in green does not
appear continuously but the display
in yellow appears each time the picture condition
changes.
Note :
a. If you press the PSM or TURBO PICTURE
button with the eye function, the eye function
is automatically switched off.
b. EYE function is not available for RGB input
source.
Turbo picture selection (option)
When this function is on, the picture will be more
brilliant and distinct than normal picture.
Repeatedly press the TURBO PICTURE button to
switch on or off.
Note :
a. If you press the PSM button with the Turbo
picture function, the Turbo picture function is
automatically switched off.
b. TURBO PICTURE function is not available for
RGB input source.
Sound adjustment (option)
Sound adjustment is an optional function only a
set with sound adjustment can perform this function.
SSM (Sound Status Memory)
You can select your preferred sound setting; Flat,
Music, Movie or Speech and you can also adjust
the sound frequency of equalizer.
1. Press the MENU button and then D / E button to select the Sound menu.
2. Press the G button to select SSM.
3. Press the G button and then D / E button to
select a sound setting on the SSM pull-down
menu.
SSM
{
SSM
TurboOSnd.{
AVL
{
Balance {
Woofer
{
Treble
{
Bass
{
X-WAVE
{
Flat
Music
Movie
Speech
User
(O} {OOKOMENU
)
i
Sound Frequency Adjustment
a. Press the G button in User to display the
User sub menu.
b. Select a sound band by pressing the F / G
button.
c. Make appropriate sound level with the D /
E button.
d. Press the OK button to store it for the
sound User.
Repeatedly press the MENU button to return to
normal TV viewing.
You can also recall a desired sound (Flat,
Music, Movie, Speech or User) with SSM/
button on the remote control. The sound Flat,
Music, Movie and Speech are programmed for
good sound reproduction at the factory and cannot be changed.
*
Note : If you press the SSM/ button after making appropriate adjustment on the User sub
menu, the display User automatically appears
even though you have already set a factory preset setting; Flat, Music, Movie or Speech.
*
X-WAVE (Wireless Sound) (option)
You can also listen to the sound through the FM
receiver.
1. Press the MENU button and then D / E button to select the Sound menu.
2. Press the G button and then D / E button to
select X-WAVE.
3. Press the G button and then D / E button to
tune in a frequency on the X-WAVE pull-down
menu.
4. Match the TV’s frequency and the FM receiver’s.
Some models are displayed as shown below.
1. Press the MENU button and then D / E button to select the Sound menu.
2. Press the G button and then D / E button to
select X-WAVE.
3. Press the G button and then D / E button to
select Set Freq.
4. Press the G button to tune in a frequency on
the X-wave menu.
5. Use the number 0 to 9 or press the F / G
button to match the TV’s frequency and the
FM receiver’s.
Note:
a. If the reception is poor or weak, select a different frequency.
b. For best results, there should be no more that
5m (16.4ft) between the TV and FM Receiver.
c. In certain areas, the FM transmitter ability
may be weak, such as near a broadcast
tower.
d. The reception sensitivity may depend on the
kinds of receiver (FM radio).
Turbo sound selection (option)
When this function is on, the sound will be more
emphasized and amplified than normal sound.
Repeatedly press the TURBO SOUND button to
switch on or off.
Sound output selection (option)
Sound adjustment
In AV mode, you can select output sound for the
left and right loudspeakers.
1. Press the MENU button and then D / E button to select the Sound menu.
2. Press the G button and then D / E button to
select the desired sound item; AVL (option),
Balance, Treble, Bass or Woofer (option).
3. Press the G button.
4. Make desired adjustment with the F / G, D /
E or OK button on each pull-down menu.
5. Repeatedly press the MENU button to return
to normal TV viewing.
Repeatedly press the I/II/ button to select the
sound output.
L+R :Audio signal from audio L input is sent to left
loud-speaker and audio signal from audio R
input is sent to right loud- speaker.
L+L : Audio signal from audio L input is sent to left
and right loud-speakers.
R+R :Audio signal from audio R input is sent to left
and right loud-speakers.
*
13
Sound adjustment (option)
Stereo/Dual reception (option)
NICAM reception (option)
When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
If your set is equipped with the receiver for NICAM
reception, the high quality NICAM (Near
Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the
type of received broadcast as follows by pressing
the I/II/ button repeatedly.
1. When NICAM mono is received, you can
select NICAM MONO or FM MONO.
2. When NICAM stereo is received, you can
select NICAM STEREO or FM MONO. If the
stereo signal is weak, switch to FM mono.
3. When NICAM dual is received, you can select
NICAM DUAL I, NICAM DUAL II or
NICAM DUAL I+II or MONO. When FM
mono is selected the display MONO appears
on the screen.
Broadcast
Mono
Stereo
Dual
On Screen Display
MONO
*
STEREO
DUAL I
Mono sound selection
In stereo reception if the stereo signal is weak,
you can switch to mono by pressing the I/II/ button twice. In mono reception the depth of sound
is improved. To switch back to stereo, press the
I/II/ button twice again.
*
*
Language selection for dual language broadcast
If a programme received in two languages (dual
language), you can switch to DUAL I, DUAL II or
DUAL I+II by pressing the I/II/ button repeatedly.
DUAL I sends the primary broadcast language to
the loudspeakers.
DUAL II sends the secondary broadcast language to the loudspeakers.
DUAL I+II sends a separate language to each
loudspeaker.
*
14
Time Setting
Setting the clock
Auto off
1. Press the MENU button and then D / E button to select the Time menu.
2. Press the G button to select Clock.
3. Press the G button and then D / E button to
If you select On on the Auto off pull-down menu,
the set will automatically switch itself to standby
mode approximately ten minutes after a TV station stops broadcasting.
Clock
Offotime
Onotime
Autoooff
{
{
{
{
-i-o:o-i-
(O} {OOKOMENU
)
i
adjust the hour.
4. Press the G button and then D / E button to
adjust the minute.
5. Press the OK button.
6. Repeatedly press the MENU button to return to
normal TV viewing.
1. Press the MENU button and then D / E button to select the Time menu.
2. Press the G button and then D / E button to
select Auto off.
3. Press the G button and then D / E button to
select On or Off on the Auto off pull-down
menu.
4. Press the OK or F button.
5. Repeatedly press the MENU button to return to
normal TV viewing.
Setting the On/Off timer
By using this function, the set automatically
switches on or off at a preset time. You must set
the time correctly before using on/off time function.
1. Press the MENU button and then D / E button to select the Time menu.
2. Press the G button and then D / E button to
select Off time/On time.
3. Press the G button and then D / E button to
adjust the hour.
4. Press the G button and then D / E button to
adjust the minute.
5. Only On time function; Press the G button
and then D / E button to adjust programme
number and volume level.
6. Press the OK button.
7. Repeatedly press the MENU button to return to
normal TV viewing.
Note :
a. On time works only in standby mode.
b. To view the remaining on/off time, select the
Time menu.
c. When you switch the main power off, the
Clock is reset .
d. Two hours after the set is switched on by the
on time function it will automatically switch
back to standby mode unless a button has
been pressed.
15
Other functions
TV and AV modes
Inputs can be set for TV or AV mode. AV mode is
used when a video cassette recorder (VCR), or
other equipment is connected to the set.
Note : When a VCR is connected via the aerial
socket the set is used in TV mode. See the
‘Connection of external equipment’ section.
1. Press the MENU button and then D / E button
to select the Special menu.
2. Press the G button and then D / E button to
select Input.
3. Press the G button and then D / E button to
select TV, AV (AV1 or AV2), AV3 (option), SVIDEO (option) or COMPONENT (option) on
the Input pull-down menu.
AV or AV1 : VCR connected to the Euro scart
socket or phone jack of the set
AV2 : VCR connected to the AV2 sockets of
the set (option)
AV3 : VCR connected to the AV3 sockets of
the set (option)
S-VIDEO : S-VIDEO socket of VCR connected
to the Euro scart socket on the set (option)
COMPONENT : DVD Player connected to the
COMPONENT sockets on the set (option)
4. Repeatedly press the MENU button to return to
normal TV viewing.
Alternatively you can select the TV or AV mode by
pressing the TV/AV button.
In AV mode, to return to TV mode, press the D / E
or NUMBER buttons.
Auto AV switching (option)
If your VCR outputs switching voltage when it is
switched to playback with the VCR connected to the
Euro scart socket. The set is automatically switched
to AV or AV1 mode when an AV signal is input. But
if you want to keep on watching TV mode, press the
D / E or NUMBER buttons. Press the TV/AV button to return to AV modes.
Child lock
The TV can be set so that the remote control
handset is needed to control it. This feature can
be used to prevent unauthorized viewing.
1. Press the MENU button and then D / E button to select the Special menu.
16
2. Press the G button and then D / E button to
select Child lock.
3. Press the G button and then D / E button to
select On or Off on the Child lock pull-down
menu.
4. Press the OK or F button.
5. Repeatedly press the MENU button to return
to normal TV viewing.
With the lock on, the display Child lock on
appears on the screen if any button on the panel
is pressed while viewing the TV.
Note : The display Child lock on will not appear
on the screen if any button on the panel is
pressed while displaying the menus.
Blue back (option)
If you select On on the Blue back pull-down
menu, the blue background appears on the
screen when there is no or poor signal.
1. Press the MENU button and then D / E button to select the Special menu.
2. Press the G button and then D / E button to
select Blue back.
3. Press the G button and then D / E button to
select On or Off on the Blue back pull-down
menu.
4. Press the OK or F button.
5. Repeatedly press the MENU button to return
to normal TV viewing.
Note : In the AV mode, Component mode, the
blue background doesn’t appear on the screen.
Other functions
Games (option)
Sleep timer
Game is an optional function, only a set with game
can perform this function by using the remote control handset.
You don’t have to remember to switch the set off
before you go to sleep. The sleep timer automatically switches the set to standby after the preset
time elapses.
Press the SLEEP button to select the number of
minutes. The display r- - - will appear on the
screen, followed by 10, 20, 30, 60, 90, 120, 180
and 240. The timer begins to count down from the
number of minutes selected.
1. Press the MENU button and then D / E button to select the Special menu.
2. Press the G button and then D / E button to
select Game.
3. Press the G button to enter the game mode.
4. Press the D / E button to select a game and
then press the OK button.
You can enjoy the game by using the GAME
owner’s manual.
Note :
a. Press the TV/AV or MENU button to return to
the normal TV viewing.
b. If you want a new game, press the RED button to start during the game.
Note :
a. To view the remaining sleep time, press the
SLEEP button once.
b. To cancel the sleep time, repeatedly press the
SLEEP button until the display r - - appears.
c. When you switch the set off, the set releases
the preset sleep time.
17
NOTE
18
Troubleshooting check list
Symptoms
No picture, no sound
Sound OK, poor picture
Picture OK, poor sound
Picture blurred
Lines or streaks in picture
Poor reception on some channels
No colour
Poor colour
Remote control does not work
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched on
Try another channel (weak signal)
Check aerial (plugged into TV?)
Check aerial (broken lead?)
Check aerial
Check for local interference
Adjust contrast
Adjust brightness
Adjust colour
Adjust volume
Check the batteries in remote control
Check Audio/Video sockets (VCR only)
19
Download PDF

advertising