LG | 32LF520A | LG 32LF520A Owner’s Manual

OWNER’S MANUAL
Safety and Reference
Please read this manual carefully before operating your set and
retain it for future reference.
www.lg.com
COV33347201
P/NO : COV33347201
Printed in China
(India region only)
ATTENTION:
This product is qualified for the BEE Star rating in the ‘Home’ Mode.
The Objectives of Star Labeling Program is designed to promote energy efficient products and practices.
When the television is initially set up, it is designed to meet the BEE Star Labeling requirements while maintaining optimum picture quality.
• Changes to certain functionalities of this television (TV Guide, Picture/sound etc) may change the power consumption.
• Depending upon such changed setting (eg., Retail mode), the power consumption may vary which possibly could exceed the stated energy
consumption.
To reset the television to Star rating qualified settings, select ‘Home’ mode from the initial set-up procedure in ‘factory settings’ under the
‘Set-up’ menu.
Safety instructions
Please read these safety precautions carefully before using the product.
ENGLISH
WARNING
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Do not place the TV and/or remote control in the following
environments:
• A location exposed to direct sunlight
• An area with high humidity such as a bathroom
• Near any heat source such as stoves and other devices that
produce heat
• Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
• An area exposed to rain or wind
• Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product
deformation.
Do not place the product where it might be exposed to dust. This may
cause a fire hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or wipe
dust off. You may be electrocuted due to excess moisture.
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, fire ignition may break out.
Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
Bend antenna cable between inside and outside building to prevent
rain from flowing in. This may cause water damaged inside the Product
and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
fire hazard.
Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in fire due to over-heating.
3
ENGLISH
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
Des
icca
nt
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suffocation. Keep it out
of the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
Do not put or store inflammable substances near the product. There is a
danger of combustion/explosion or fire due to careless handling of the
inflammable substances.
4
Do not drop metallic objects such as coins, hair pins, chopsticks or wire
into the product, or inflammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, fire or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
CAUTION
ENGLISH
If any of the following occur, unplug the product immediately and
contact your local service centre.
Install the product where no radio wave occurs.
• The product has been impacted by shock
• The product has been damaged
• Foreign objects have entered the product
• The product produced smoke or a strange smell
This may result in fire or electric shock.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause fire hazard
and insulation deterioration can cause electric leakage/shock/fire.
Do not install the product on places such as unstable shelves or inclined
surfaces. Also avoid places where there is vibration or where the
product cannot be fully supported. Otherwise, the product may fall or
flip over, which may cause injury or damage to the product.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise, this may result in electric shock or fire.
If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), fix
it carefully so as not to drop.
Only use the attachments / accessories specified by the manufacturer.
Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may create a
fire hazard or an electric shock hazard.
Never Disassemble the AC adapter or power cord. This may result in fire
or electric shock.
5
ENGLISH
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Do not turn the product On/Off by plugging-in or unplugging the power
plug to the wall outlet. (Do not use the power plug for switch.) It may
cause mechanical failure or could give an electric shock.
Only use the specified type of battery. This could cause damage to the
remote control.
Please follow the installation instructions below to prevent the product
from overheating.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
• The distance between the product and the wall should be more
than 10 cm.
• Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
• Do not install the product on a carpet or cushion.
• Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open fireplace and electric heaters.
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its
sensor.
Signal from Remote Control can be interrupted due to external/internal
lighting eg Sunlight, fluorescent lighting. If this occurs turn off lighting
or darken viewing area.
When connecting external devices such as video game consoles, make
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
6
Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not affect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet. This may cause
a fire hazard.
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
Avoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this unit
by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling at
the plug.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
ENGLISH
Do not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may cause damage
to screen.
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Contact the service centre once a year to clean the internal parts of the
product.
Accumulated dust can cause mechanical failure.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
The panel is a high technology display product with resolution of two
million to six million pixels. You may see tiny black dots and/or brightly
coloured dots (red, blue or green) at a size of 1 ppm on the panel. This
does not indicate a malfunction and does not affect the performance
and reliability of the product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
When moving the product, make sure you turn the power off first. Then,
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
WARNING: To prevent the spread of fire, keep candles or other open
flames away from this product at all times.
7
Preparing
ENGLISH
NOTE
You may find different brightness and color of the panel depending on
your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
* Disclaimer
LG LED TVs are LCD TVs with LED backlighting.
Displaying a still image (e.g., broadcasting programme logo, on-screen
menu, scene from a video game) for a prolonged time may cause
damage to the screen, resulting in retention of the image, which is
known as image sticking. The warranty does not cover the product for
image sticking.
Avoid displaying a fixed image on your television’s screen for a
prolonged period (2 or more hours for LCD, 1 or more hours for Plasma).
Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking
may occur on the borders of the panel.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
Generated sound
“Cracking” noise: A cracking noise that occurs when watching or turning
off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product.
This generated sound does not affect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
8
• Image shown may differ from your TV.
• Your TV’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
• The available menus and options may differ from the input source
or product model that you are using.
• New features may be added to this TV in the future.
• The TV can be placed in standby mode in order to reduce the power
consumption. And the TV should be turned off if it will not be
watched for some time, as this will reduce energy consumption.
• The energy consumed during use can be significantly reduced if the
level of brightness of the picture is reduced, and this will reduce
the overall running cost.
• The items supplied with your product may vary depending on the
model.
• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
• For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI cable types)
- High-Speed HDMI®/™ cable (3 m or less)
- High-Speed HDMI®/™ cable with Ethernet (3 m or less)
CAUTION
• Do not use any unapproved items to ensure the safety and product
life span.
• Any damage or injuries caused by using unapproved items are not
covered by the manufacturer’s warranty.
• Some models have a thin film attached on to the screen and this
must not be removed.
• When attaching the stand to the TV set, place the screen facing
down on a cushioned table or flat surface to protect the screen
from scratches.
• Make sure that the screws are fastened completely. (If they are
not fastened securely enough, the TV may tilt forward after being
installed.) Do not use too much force and over tighten the screws;
otherwise screw may be damaged and not tighten correctly.
Lifting and moving the TV
Cleaning your TV
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
Clean your TV regularly to keep the best performance and to extend the
product lifespan.
• Make sure to turn the power off and disconnect the power cord and
all other cables first.
• When the TV is left unattended and unused for a long time,
disconnect the power cord from the wall outlet to prevent possible
damage from lightning or power surges.
ENGLISH
Maintenance
• It is recommended to move the TV in the box or packing material
that the TV originally came in.
• Before moving or lifting the TV, disconnect the power cord and
all cables.
• When holding the TV, the screen should face away from you to
avoid damage.
Screen, frame, cabinet and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and
soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in
clean water or a diluted mild detergent. Then wipe immediately with
a dry cloth.
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not push, rub, or hit the screen surface with your fingernail or a
sharp object, as this may result in scratches and image distortions.
• Do not use any chemicals as this may damage the product.
• Do not spray liquid onto the surface. If water enters the TV, it may
result in fire, electric shock, or malfunction.
Power cord
• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
• When transporting a large TV, there should be at least 2 people.
• When transporting the TV by hand, hold the TV as shown in the
following illustration.
Remove the accumulated dust or dirt on the power cord regularly.
• When transporting the TV, do not expose the TV to jolts or
excessive vibration.
• When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
• Do not apply excessive pressure to cause flexing /bending of frame
chassis as it may damage screen.
• When handling the TV, be careful not to damage the protruding
joystick button.
CAUTION
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not move the TV by holding the cable holders, as the cable
holders may break, and injuries and damage to the TV may occur.
9
Using the keyboard button
Mounting on a table
You can operate the TV by pressing the keyboard buttons.
(Depending on model)
ENGLISH
1 Lift and tilt the TV into its upright position on a table.
Programme Up/ Down
• Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
Volum e Up/ Down
OK Button
SERVICE
ONLY
10 cm
10 cm
10 cm
10 cm
SETTING Button
2 Connect the power cord to a wall outlet.
INPUT Button
Power On / Off
CAUTION
• Do not place the TV near or on sources of heat, as this may result in
fire or other damage.
WARNING
If a television is not positioned in a sufficiently stable location, it can
be potentially hazardous due to falling. Many injuries, particularly to
children, can be avoided by taking simple precautions such as:
Adjusting the Menu
SERV
OK
INPUT
Press OK to access the setting.
1. Press INPUT to select input.
2. When Power off mode, then can
access the setting
MOVE Press + / – to move left/right on a
left/right menu or a submenu.
RVICE
NLY
1.Press Λ / V to move up/down on a
MOVE
menu or a submenu.
up/down 2. When Power off mode, then can
access the setting
10
MENU/
EXIT
1. When there is no OSD on the
screen, press SETTING can access
the menu settings.
2. When there is an OSD on the
screen, press SETTING can exit
the menu settings.
• Using cabinets or stands recommended by the manufacturer of
the television.
• Only using furniture that can safely support the television.
• Ensuring the television is not overhanging the edge of the
supporting furniture.
• Not placing the television on tall furniture (for example, cupboards
or bookcases) without anchoring both the furniture and the
television to a suitable support.
• Not standing the televisions on cloth or other materials placed
between the television and supporting furniture.
• Educating children about the dangers of climbing on furniture to
reach the television or its controls.
Securing the TV to a wall
(This feature is not available for all models.)
10 cm
ENGLISH
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
Separate purchase (Wall mounting bracket)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
CAUTION
Model
32LF520*
VESA (A x B)
200 x 200
Standard screw
M6
Number of screws
4
Wall mount bracket (optional)
LSW240B
MSW240
A
B
• Make sure that children do not climb on or hang on the TV.
NOTE
• Use a platform or cabinet that is strong and large enough to
support the TV securely.
• Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the
use of LG’s wall mount bracket. When you do not use LG’s wall mount
bracket, please use a wall mount bracket where the device is adequately
secured to the wall with enough space to allow connectivity to external
devices.
11
CAUTION
ENGLISH
• Disconnect the power first, and then move or install the TV.
Otherwise electric shock may occur.
• Remove the stand before installing the TV on a wall mount by
performing the stand attachment in reverse.
• If you install the TV on a ceiling or slanted wall, it may fall and
result in severe injury. Use an authorised LG wall mount and
contact the local dealer or qualified personnel.
• Do not over tighten the screws as this may cause damage to the TV
and void your warranty.
• Use the screws and wall mounts that meet the VESA standard. Any
damages or injuries by misuse or using an improper accessory are
not covered by the manufacturer’s warranty.
Attaching the shelf stand
Stand
M4 x L20 mm
How to attach to masonry walls
Use the anchors for wall material of concrete, light concrete, strong
natural stone, soft natural stone masonry brick and hallow block that
do not crack.
Please follow the below direction
- Check the material of the wall and the thickness of the finishing.
- When installing the product on wall material not designated,
install the product so that each fixated location can withstand
the pull out load of 70 kgf (686 N) and shear load of 100 kgf (980
N) or above.
- Use the Ø8 mm drill bit for concrete and hammer (Impact) drill.
1
2
Wall mount anchor
3
4
12
Wall mount screw
5
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
ENGLISH
6
Connections (notifications)
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
NOTE
1 Use a drill bit Ø8 mm to drill a hole for the anchor location within a
depth of 80 mm - 100 mm.
2 Clean the drilled hole.
3 Insert the sealed anchor to the hole. (When inserting the anchor,
use a hammer.)
4 Set the wall mount on the wall by aligning to the location of the
hole. and, set the angle adjusting part to face upward.
5 Align the wall mount bolt to the hole and tighten it. Then, fasten the
bolts at torque of 45 kgf/cm - 60 kgf/cm.
• The external device connection may differ from the model.
• Connect external devices to the TV regardless of the order of the
TV port.
• If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
• Refer to the external equipment’s manual for operating
instructions.
• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal amplifier properly to
improve the image quality.
• If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
• An antenna cable and converter are not supplied.
Antenna Booster
• This feature improves the sensitivity to weak RF Signal
in poor reception areas. LG’s built-in booster is autoactivated at weak signal level. It strengthens signal level
and minimizes picture colour noise.
• This feature is auto-controlled by processor and no user
intervention required.
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
13
Remote control
FAV
B
(Depending on model)
ENGLISH
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
1
C
CAUTION
• Do not mix old and new batteries, as this may damage the remote
control.
• In Analogue TV and some countries, some remote control buttons
may not work.
• The remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor
on the TV.
B
Adjusts the volume level.
AV
MODE
Accesses your favourite programme list.
Selects the sound output.
A
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
C
A
(POWER) Turns the TV on or off.
1 Teletext buttons These buttons are used for teletext.
Returns to the TV viewing from any mode.
Accesses the Quick menus.
Changes the image mode.
Accesses the main menus.
Navigation buttons (up/down/left/right) Scrolls through
menus or options.
Selects an AV mode. (Depending on model)
Changes the input source.
Number buttons Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
14
Selects menus or options and confirms your input.
Returns to the previous level.
Clears on-screen displays and returns to TV viewing.
Control buttons (
) Controls the USB menus.
Coloured buttons These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
Licenses
Watching TV
Supported licenses may differ by model.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
ENGLISH
Turning the TV on for the first time
When you turn the TV on for the first time, the Initial setting screen
appears. Select a language and customize the basic settings.
1 Connect the power cord to a power outlet. The Power indicator turns
red and the TV switches to Standby mode.
2 In Standby mode, press the power button on the remote control or
local key to turn the TV on. The Initial setting screen appears if you
turn the TV on for the first time.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
NOTE
• You can also access Factory Reset by accessing OPTION in the
main menu.
3 Follow the on-screen instructions to customize your TV settings
according to your preferences.
Selects a language to display.
Menu Language
This DivX Certified® device has passed rigorous testing to ensure it
plays DivX® video.
To play purchased DivX movies, first register your device at vod.divx.
com. Find your registration code in the DivX VOD section of your device
setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
Mode Setting
Selects Home Use for the home
environment.
Time Setting
Sets the time.
Auto Tuning
Scans and saves available
programmes automatically.
DivX®, DivX Certified® and associated logos are trademarks of DivX, LLC
and are used under license.
NOTE
Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274.
• To display images in the best quality for your home environment,
select Home Use.
• Store Demo is suitable for the retail environment.
• If you select Store Demo, any customized settings will switch
back to the default settings of Store Demo in 5 minutes.
4 When the basic settings are complete, press the
.
NOTE
• If you do not complete the Initial setting, it will appear whenever
the TV turns on.
• Disconnect the power cord from the power outlet when you do not
use the TV for a long period of time.
5 To turn the TV off, press the power button on the remote control.
15
Assigning a station name
Watching TV
1 In Standby mode, press
2 Press
You can assign a station name with five characters to each programme
number.
(POWER) to turn the TV on.
INPUT and select TV.
ENGLISH
3 To turn the TV off, press
mode.
(POWER). The TV switches to Standby
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Manual Tuning.
3 Press the Navigation buttons to scroll to Name.
4 Press the Navigation buttons to scroll to select the position and make
your choice of the second character, and so on. You can use an the
alphabet A to Z, the number 0 to 9, +/ -, and blank and press OK .
Managing programmes
Automatically setting up programme
5 Press the OK
Use this to automatically find and store all available programmes.
6 When you return to the previous menu, press
1 Press SETTINGS and the Navigation buttons to scroll to SETUP and
.
press
Fine Tuning
2 Press the Navigation buttons to scroll to Auto Tuning and press
.
3 Press the Navigation buttons to scroll to To Start and select To Start
to begin auto tuning. The TV scans and saves available programmes
automatically.
4 When you return to the previous menu, press
.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Manual Tuning.
3 Press the Navigation buttons to scroll to Fine.
4 Press the Navigation buttons to fine tune for the best picture and
sound.
to store it.
Manually setting up programme
6 When you return to the previous menu, press
Manual Tuning lets you manually tune and arrange the stations in
whatever order you desire.
Editing your programme list
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
2 Press the Navigation buttons to scroll to Manual Tuning.
3 Press the Navigation buttons to scroll to Storage.
.
Normally fine tuning is only necessary if reception is poor.
5 Press the OK
.
When a programme number is skipped, it means that you will be
unable to select it using
button during TV viewing.
4 Press the Navigation buttons or Number buttons to select the desired
programme number.
If you wish to select the skipped programme, directly enter the
programme number with the NUMBER buttons or select it in the
Programme edit menu.
5 Press the Navigation buttons to scroll to System.
This function enables you to skip the stored programmes.
6
Press the Navigation buttons to scroll to TV System.
7
Press the Navigation buttons to scroll to Band.
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
8
Press the Navigation buttons to scroll to V/UHF or Cable.
9
Press the Navigation buttons to scroll to Channel.
11 Press the Navigation buttons to scroll to Search.
12 Press the Navigation buttons to scroll and start Searching.
13 Press the OK
to store it.
14 When you return to the previous menu, press
NOTE
• To store another programme, repeat steps 3 to 13.
2 Press the Navigation buttons to scroll to Programme Edit.
3 Edit programmes using the following buttons.
10 Press the Navigation buttons and then select the desired Channel
number with the Navigation buttons or Number buttons.
16
to store it.
.
Button
Description
Deletes a programme.
Red button
ENGLISH
Press the Red button twice. The selected
programme is deleted, all the following
programmes are shifted up one position.
- Just Scan : Displays video images in the original size without
removing parts of the edge of the image. (This function works
in Component/HDMI (720p / 1080i / 1080p) Mode.)
Moves a programme.
Yellow button
Blue button
Press the Yellow button again to release this
function.
Selects a programme number to be skipped. Press
the Blue button again to release the skipped
programme.
4 When you return to the previous menu, press
.
Selecting a programme on the programme
list
NOTE
• If you select Just Scan, you may see image noises at the edge of
the original signal.
- Original : When your TV receives a wide screen signal it will
automatically change to the picture format broadcasted.
(4:3
4:3)
(16:9
16:9)
1 Press LIST to access the programme list.
2 Press the Navigation buttons to select to desired programme and
press OK .
3 When you return to the previous menu, press LIST.
NOTE
- 4:3 : Resizes images to the previous standard 4:3.
• You may find some blue programmes. They have been set up to be
skipped by auto programming or in the programme edit mode.
• Some programmes with the programme number shown in the
programme list indicate there is no station name assigned.
Using additional options
Adjusting aspect ratio
Resize an image to view at its optimal size by pressing Q.MENU or
accessing Aspect Ratio in the PICTURE menu.
- 14:9 : You can view a picture format of 14:9 or a general TV
programme in the 14:9 mode. The 14:9 screen is viewed in the
same way as in 4:3, but is moved to the up and down.
NOTE
• The available ratio varies depending on the input source.
- 16:9 : Resizes images to fit the screen width.
- Zoom : Formats an image to fit the screen width. The top and
bottom of the image may not appear.
17
NOTE
• If you enlarge or reduce an image, the image may be distorted.
Using the input list
To disconnect a USB storage device,
make sure to end the connection properly to prevent damages to the
TV or files.
ENGLISH
1 Press Q.MENU to access the quick menus.
2 Press the Navigation buttons to scroll to Eject and press OK
Using the input list
Selecting an input source
INPUT to access the input sources.
1 Press
.
3 Disconnect the USB storage device only when the message says that
it is safe to remove.
CAUTION
• The connected device displays on each input source.
2 Press the Navigation buttons or input button to scroll to one of the
input sources and press OK .
* Image shown may differ from your TV.
• Do not turn the TV off or remove a USB storage device while the
USB storage device is connected to the TV, as this could result in
loss of files or damage to the USB storage device.
• Back up your files saved on a USB storage device frequently, as you
may lose or damage the files and this may be not covered by the
manufacturer’s warranty.
Input List
Tips for using USB storage devices
Antenna
AV
Component
HDMI 1
HDMI 2
Input Label
Input source
Description
Antenna
Watch TV over the air and cable broadcast.
AV
Watch video from a VCR or other external
devices.
Component
Select it when using the DVD or the Digital
set-top box depends on connector.
Watch video from a HTS or other high
definition devices.
HDMI 1/2
USB
(Depending on model)
* Image shown may differ from your TV.
Connecting USB storage devices
Connect USB storage devices (USB memory) to the TV and use
multimedia features (See "" on page 19).
USB IN
Connect a USB flash memory or USB memory card reader to the TV as
shown on the following illustration.
18
• Only a USB storage device is recognizable.
• If the USB storage device is connected through a USB hub, the
device is not recognizable.
• A USB storage device using an automatic recognition programme
may not be recognized.
• A USB storage device which uses its own driver may not be
recognized.
• The recognition speed of a USB storage device may depend on
each device.
• Please do not turn off the TV or unplug the USB device when
the connected USB storage device is working. When such device
is suddenly separated or unplugged, the stored files or the USB
storage device may be damaged.
• Please do not connect the USB storage device which was artificially
manoeuvred on the PC. The device may cause the product to
malfunction or fail to be played. Never forget to use only a USB
storage device which has normal music files, image files or movie
files.
• Please use only a USB storage device which was formatted as a
FAT16, FAT32, NTFS file system.
• Please connect a USB storage device with the cable offered by the
device maker.
• Some USB storage devices may not be supported or operated
smoothly.
• Be sure to back up important files since data stored in a USB
memory device may be damaged. We will not be responsible for
any data loss.
• If a USB memory device is connected to a USB multi-card reader, its
volume data may not be detected.
• If the USB memory device does not work properly, disconnect and
reconnect it.
Using the USB
This TV allows you to enjoy movie, music and photo files stored on a USB
device connected to the USB port.
ENGLISH
• How fast a USB memory device is detected differs from device to
device.
• The recommended capacity is 32 GB or less for USB memory.
• Any device with more than the recommended capacity may not
work properly.
• USB storage devices below USB 2.0 are supported as well. But they
may not work properly in the movie list.
• Maximum of 198 folders or files can be recognized under one
folder.
• If there are a lot of folders or files all within one folder, the device
may not be able to access these properly.
• It is recommended that you use devices with a rated voltage of less
than 5 V and a rated current of less than 0.5A.
Terminology
The TV can control and play content from a USB device.
Notes:
• Do not insert/remove a USB device while in use.
• MENU is not available during playback.
Media Player Specifications
Device
USB device:
Interface version: USB2.0 HS
USB Mass Storage Class devices (MSC)
Notes:
• Connectivity is not guaranteed for all devices.
• Incorrect behaviour may occur with a USB hub
connection.
• The Auto Format function is not available.
• The aspect ratio may not be correct in some cases.
Supported file system
• FAT16, FAT32 and NTFS
You must obtain any required permission from
copyright owners to download or use copyrighted
content. LG cannot and does not grant such
permission.
Basic operation
You will be asked if you want to start the Media Player whenever a USB
device is inserted.
Using USB
You must manually start the Media Player from the menu.
❶ Insert a USB device into the USB terminal on the left side of the TV.
❷ A confirmation message will appear. Highlight Yes, and then press
OK.
❸ Press ꔌ or ꔍ to select Photo, Movie or Music and then press OK.
The list window will appear. Multi View will appear.
Manual Start
❶ Insert a USB device into the USB terminal on the left side of the TV.
❷ From the USB menu, highlight Photo list, and then
press OK.
❸ Press or to select Photo list, Music list or Movie list and press OK.
The list window will appear. Multi View will appear.
To select a file in the Multi View:
❶ Press ꔌorꔍ to select a file or folder.
❷ Select a file and press OK to start playback. Select a folder and press
OK to move to the next layer.
To return to the previous layer, press BACK.
To close the USB
Press EXIT.
19
ENGLISH
Viewing Photo Files
Playing music files
To view in Single View mode
There are three types of viewing modes.
Multi View
This view allows you to search for photos in a grid
format.The pictures are displayed using thumbnail data
in each image file.
You can listen to music from a Multi View of available files.
Multi View
Photo
/USB/
Artists
Albums
❶ Press P∧, P∨ to select a file, folder or page up/down the Multi
BUSINESS LIFE
Select
ENTER Enter
CH Page
CH RTN Back
The initial highlighted position will be on the top left
thumbnail in the Multi View.
❶ Press ꔌ or ꔍto select a photo or folder. P^ or P∨ buttons can be
used to page up/down the Multi View when there are more photos
than will fit onto one screen.
❷ When you select a folder, press OK to move to the next layer. Press
BACK to move back to the previous layer.
❸ Press OK to view the selected photo in Single View mode.
Single View
In this mode, only files located in the selected directory will be
displayed. This view allows you to change the photo content manually.
When moving from Multi View to Single View, the currently selected
photo will be displayed.
❶ Press ▶ to view the next photo. Press◀to view the previous photo.
❷ Press ꔌ to rotate the image 90° counterclockwise.
Press ꔍto rotate the image 90° clockwise.
Slide Show
This view allows you to watch a slide show of your photos. In this mode,
only files located in the selected directory will be played.
❶ To start slideshow, press OK in the Single View mode.
❷ Press ◀or ▶to view the previous/next photo.
To set Interval Time setting:
❶ Press Q.MENU to open the QUICK MENU.
❷ Press ꔌ or ꔍ to select Interval Time.
❸ Press ◀ or ▶to select 3sec, 5sec, 10sec, 15sec,30sec, 60sec, or
90sec.
Viewing photo files and playing music files at the same time
While viewing photo files, you can listen to music from a list of available
files.
❶ While viewing photos in the Single View or Slide Show mode, press
the Q.MENU button to open the QUICK MENU.
❷ Highlight Background Music and press the OK button.
The music list appears.
❸ Select a music file and press the OK button to start playback.
❹ Press BACK to move back to photo view mode.
The music is now playing in the background.
Using the sort
While viewing photo files, you can sort elements in the order.
❶ Press the Q.MENU to open the QUICK MENU.
❷ Highlight Sort and press the ◀ or ▶button.
❸ Press BACK to move back to photo view mode.
To close the Photo Viewer
❶ Press EXIT.
20
View when there are more files than will fit onto one screen.
❷ When you select a folder, press OK to move to the next layer. Press
BACK to move back to the previous layer.
❸ With the desired file selected, press OK or (play) to start
playback.
Notes:
Depending on the file size, it may take some time for playback to
begin.During playback, you can adjust the sound preferences from the
Q.MENU.
To set the repeat mode:
❶ Press Q.MENU to open the QUICK MENU.
❷ Press ꔌ or ꔍ to select Repeat.
❸ Press ◀ or ▶ to select Off , All or 1.
Mode
Off
All
1
Description
Files in the same folder are played back once.
Files in the same folder are repeatedly played back.
The same file is repeatedly played back.
❹ Press BACK.
Using the sort
While viewing music files, you can sort elements in the order.
❶ Press the Q.MENU to open the QUICK MENU.
❷ Highlight Sort and press the ◀ or ▶ button.
❸ Press BACK to move back to music view mode.
Closing the Music Player:
❶ Press EXIT.
Viewing movie files
You can select movies from a Multi View of available files.
Multi View
Movie
Setting the sleep timer
❶ Press Q.MENU to open the QUICK MENU.
❷ Press ꔌ or ꔍ to Sleep timer.
(Reference P.28 of sleep timer setting.)
ENGLISH
/USB/
Check Device Information.
It show the USB device Product Name and Capacity two items.
❶ Press Q.MENU to open the QUICK MENU.
❷ Press ꔌ or ꔍ to select Device Information.
❸ Press OK .
To close the Movie Viewer
2F WEIVER RF record
Select
ENTER Enter
CH Page
RTN
Back
❶ Pressꔌor ꔍ to select a file or folder. P^ or Pv buttons can be used
to page up/down the Multi View when there are more files than
will fit onto one screen.
❷ When you select a folder, press OK to move to the next layer.
Press BACK to move back to the previous layer.
❸ With the desired file selected, press OK to start playback.
❹ Press ■ to stop playback.
Note:
If playback finishes before ■ is pressed, the screen will return to the
Multi View.
During playback:
• Press II to pause.
PAUSE may not be available depending on the contents.
• To resume normal playback, press  (play).
• To play in fast reverse or fast forward directions, press or 
during playback. Each time you press the or , the playback
speed will change.
• Press Q.VIEW to display the file status information (content number,
movie title, progress time etc.).
Notes:
• The information may not be correctly displayed depending on the
contents.
• The playback speed (/ ) may not change depending on
the contents.
Setting the repeat mode
❶ Press Q.MENU to open the QUICK MENU.
❷ Press ꔌ or ꔍ to select Repeat.
❸ Press ◀ or ▶ to select Off , All or 1.
Mode
Description
Off
The file is played back only once.
All
Files in the same folder are repeatedly played back.
1
The same file is repeatedly played back.
❹ Press BACK.
Press EXIT.
Tips for using playing video files
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Some user-created subtitles may not work properly.
Some special characters are not supported in subtitles.
HTML tags are not supported in subtitles.
Subtitles in languages other than the supported languages are
not available.
Changing font and colour in subtitles is not supported.
Subtitles in languages other than one specified are not supported.
Video files with subtitle files if too larger may not be played
properly.
The screen may suffer temporary interruptions (image stoppage,
faster playback, etc.) when the audio language is changed.
A damaged movie file may not be played correctly, or some player
functions may not be usable.
Movie files produced with some encoders may not be played
correctly.
If the video and audio structure of recorded file is not interleaved,
either video or audio is outputted.
Videos with resolutions higher than 1920 X 1080 @ 25/30P or 1280
x 720 @ 50/60P may not work properly depending on the frame.
Movie files other than the specified types and formats may not
work properly.
Max bit rate of playable movie file is 20 Mbps. (only, Motion JPEG
: 10 Mbps)
We do not guarantee smooth playback of profiles encoded level 4.1
or higher in H.264/AVC.
DTS Audio codec is not supported.
A movie file with large size file is not supported for playback. The
file size limit is dependent on the encoding environment.
A DivX movie file and its subtitle file must be located in the same
folder.
A video file name and its subtitle file name must be identical for it
to be displayed.
Playing a video via a USB connection that doesn’t support high
speed may not work properly.
Files encoded with GMC (Global Motion Compensation) and Qpel
(Quarterpel Motion Estimation) may not be played.
Trick Mode does not support other functions than if video files do
not have index information.
Video file names that contain special characters may not be
playable.
21
Support Subtitle formats
*Maximum data transfer rate: 20Mbps
ENGLISH
External supported subtitle formats
.srt
SubRip
.smi
SAMI
Remark
.SUB
SubViewer1.0 & 2.0 only
SubViewer
MicroDVD
DVDsubtitleSystem
SubIdx(Vobsub)
.ass/.ssa
.txt
SubStation Alpha
Tmplayer
Internal supported subtitle formats
.AVI/.DIVX
XSUB generated from DixX6
Support Video formats
*Maximun:1920x1080@30p (only Motion JPEG 640x480@30p)
video
Container
File extension
Video codec
ASF
.asf
.wmv
.asf
.wmv
.wma
.avi
.divx
VC-1
(WMV3,WVC1)
Window Media Audio Standard
audio
video
AVI
audio
video
TS
audio
video
PS
.ts
.trp
.tp
.vob
audio
22
video
MP4
MOV
.mp4
.mov
audio
MP4
.mp4
.mov
Remark
Support WMA7,8,9
Standard
MPEG2
MPEG4 Part2
DivX3.11
DivX4
DivX5
DivX6
XviD
H.264/AVC
HE-AAC
LPCM
ADPCM
Dolby Digital
MP3
H.264/AVC
MPEG2
MP3
Dolby Digital
AAC
HE-AAc
MPEG1
MPEG2
Dolby Digital
DVD LPCM
MPEG4 Part2
XVID
H.264/AVC
AAC
MP3
same as AC3
same as AC3
same as AC3
video
MKV
.mkv
MPEG2
MPEG4 Part2
H.264/AVC
HE-AAC
Dolby Digital
MP3
LPCM
MPEG1
MPEG2
Dolby Digital
LPCM
MPEG1
MP2
audio
PS
.mpg
.mpeg
audio
video
audio
dat
dat
video
FLV
.flv
RM
.rm
.rmvb
same as AC3
Sorenson H.263
H.264/AVC
MP3
audio
video
ENGLISH
video
same as AC3
AAC
RV30
RV40
AAC
HE-AAC
cook: COOK (RealAudio6)
audio
Support Audio formats
File type
Bit rate
Sample freq.
Audio codec
mp3
32Kbps - 320Kbps
16kHz - 48kHz
MPEG1 Layer3
MPEG2 Layer3
MPEG2.5 Layer3
Remark
Support Photo formats
Category
2D
jpeg
Available file type
Photo size
Minimum: 64 x 64
Maximum:
Normal Type: 15360(W) x 8640(H)
Progressive Type: 1024(W) x 768(H)
SOF0
Baseline
SOF1
Extend Sequential
SOF2
Progressive
Remark
23
DivX® VOD Guide
5 Press the Navigation buttons to select Yes to confirm.
Deregistration code :
********
Deregister at http://vod.divx.com
Continue with registration?
Registration
ENGLISH
Deregistration
Yes
No
Close
6 When you are finished, press EXIT. When you return to the previous
menu, press BACK.
DivX® VOD Registration
In order to play purchased or rented DivX® VOD contents, you should
register your device with 10 digit DivX registration code from your
device at www.divx.com/vod.
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to USB and press OK
Customizing TV setting
* Image shown may differ from your TV.
.
3 Press the Navigation buttons to scroll to DivX(R) VOD and press
OK .
Accessing main menus
1 Press SETTINGS to access the main menus.
4 Press the Navigation buttons to scroll to Registration and press
OK .
2 Press the Navigation buttons to scroll to one of the following menus
and press OK .
5 View the registration code of your TV.
3 Press Navigation buttons to scroll to the setting or option you want
and press OK .
You must register your device to
play DivX(R) protected videos.
Registration code : **********
Register at http://vod.divx.com
4 When you are finished, press EXIT.
Menu
Description
Close
PICTURE
6 When you are finished, press EXIT. When you return to the previous
menu, press BACK.
DivX® VOD Deregistration
You should deregister your device with 10 digit DivX deregistration code
from your device at www.divx.com/vod.
Adjusts the image size,
quality, or effect.
AUDIO
Adjusts the sound quality,
effect, or volume level.
SETUP
Sets up and edit
programmes.
TIME
Sets the time, date, or
timer feature.
OPTION
Customizes the general
settings.
NOTE
• Once the deregistration is executed, you must register your device
again to see DivX® VOD contents.
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to USB and press OK
.
3 Press the Navigation buttons to scroll to DivX(R) VOD and press
OK .
4 Press the Navigation buttons to scroll to Deregistration and press
OK .
24
LOCK
Locks or unlocks
programmes.
INPUT
Views the input sources
with their labels.
USB
Displays photo and play
music, movie.
The available picture settings are described in the following.
Customizing settings
Setting
SETUP settings
Aspect Ratio
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
Reduces the power consumption by adjusting
the screen brightness.
BACK.
Option
* Image shown may differ from your TV.
SETUP
Off
Move
ENGLISH
1 Press SETTINGS and the Navigation buttons to scroll to SETUP.
Description
Changes the image size to view images at its
optimal size. (See p. 17)
OK
Auto Tuning
Manual Tuning
Energy Saving
Programme Edit
The Energy Saving is off
Minimum/
Medium/
Maximum
Selects the brightness level.
Screen off
The screen turns off in 3
seconds.
NOTE
• When you select Screen Off, the screen
will be turned off in 3 seconds and Screen
Off will start.
• If you adjust “Energy Saving- Maximum”,
Backlight feature will not work.
PICTURE settings
1 Press SETTINGS and the Navigation buttons to scroll to PICTURE.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
Selects one of the preset image or customizes
options in each mode for the best TV screen
performance. You are also able to customize
advanced options of each mode.
BACK.
* Image shown may differ from your TV.
Mode
PICTURE
Move
Aspect Ratio
: 16:9
ꕊ Energy Saving
Picture Mode
: Off
Vivid
Adjusts the video image
for the retail environment
by enhancing the contrast,
brightness, colour, and
sharpness.
Standard
Adjusts the image for the
normal environment.
Cinema
Optimizes the video images
for a cinematic look to enjoy
movies as if you are in a movie
theatre.
Soccer
Optimizes the video image for
high and dynamic actions by
emphasizing primary colours
such as white, grass, or sky
blue.
Game
Optimizes the video image for
a fast gaming screen such as
PCs or games.
OK
: Standard
• Backlight
100
• Contrast
100
• Brightness
50
• Sharpness
20
• Colour
55
• Tint
• Colour Temperature
• Advanced Control
• Reset
Picture Mode
0
R
G
C20
W
C
25
Basic image options
Advanced image options (Depending on model)
ENGLISH
Setting
Description
Backlight
Adjusts the brightness of the screen
by controlling the LCD backlight. If
you decrease the brightness level, the
screen becomes darker and the power
consumption will be reduced without
any video signal loss.
Setting
Description
Dynamic Contrast
Adjusts the contrast to keep it at the best
level according to the brightness of the
screen. The picture is improved by making
bright parts brighter and dark parts darker.
Dynamic Colour
Contrast
Increases or decreases the gradient
of the video signal. You may use
Contrast when the bright part of the
picture is saturated.
Adjusts screen colours so that they look
livelier, richer and clearer. This feature
enhances hue, saturation and luminance
so that red, blue and green white look
more vivid.
Brightness
Adjusts the base level of the signal in
the picture.
Skin Colour
Sets Skin colour spectrum separately to
implement the skin colour as defined by
the user.
Adjusts the level of crispness in the
edges between the light and dark
areas of the picture. The lower the
level, the softer the image.
Sky Colour
Sky colour is set separately.
Sharpness
Colour
Tint
Adjusts intensity of all colours.
Advanced Control
Reset
Noise Reduction
Adjusts the balance between red and
green levels.
Adjusts the overall tone of the screen
as desired.
Colour Temperature
Grass Colour
Natural colour spectrum (meadows , hills ,
etc.) can be separately set.
Reduces screen noise without compromising
video quality.
You can adjust brightness of dark area and
middle gray level area of the picture.
Gamma
Set to warm to enhance hotter colours
such as red, or set to cool to see less
intense colours with more blue.
Low: Make the dark and middle gray level
areas brighter.
Medium: Express the original picture level.
High: Make the dark and middle gray level
area darker.
Customizes the advanced options.
Sets black level of the screen to proper level.
This function is available in the following
modes: RF, AV, HDMI, Component.
Restores the options of each mode to
the factory default.
Black Level
Low: The reflection of the screen gets darker.
High: The reflection of the screen gets
brighter.
Auto: The reflection of the the screen gets
optimal.
Real Cinema
Makes video clips recorded in film look more
natural.
NOTE
• Depending on input signal or other picture settings, the range of
detailed items for adjustment may differ.
26
AUDIO settings
Setting
1 Press SETTINGS and the Navigation buttons to scroll to AUDIO.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
Mode
BACK.
* Image shown may differ from your TV.
AUDIO
Move
Auto Volume
TV Speaker
Music
Select when you listen to
music.(Bollywood is india
special music mode)
: On
Balance
Sound Mode
OK
Standard
Select when you want
standard-quality sound.
0
: Standard
• Treble
• Bass
• Reset
L
R
50
Cinema
Select when you watch
movies.
Soccer
Select when you watch
sports events.
Game
Select when you play
games.
ENGLISH
3 When you return to the previous menu, press
Description
Selects one of the preset sound modes or
customizes options in each mode.
50
: On
Sound Mode
Option
The available audio settings are described in the following.
Setting
Description
Auto Volume
Activates the Auto Volume feature to keep the
volume level consistent whenever you change
programmes. The volume level may not be
consistent due to different signal conditions of
broadcasting stations.
Balance
Adjust balance between the left and right
speakers according to your room environment.
TV Speaker
Treble
Controls the dominant
sounds in the output. When
you turn up the treble, it
will increase the output to
the higher frequency range.
Bass
Controls the softer sounds in
the output. When you turn
up the bass, it will increase
the output to the lower
frequency range.
Reset
Resets the sound mode to
the default setting.
Turns off the internal speaker of the TV when
using an external Hi-Fi system.
This feature may not be applied based on country broadcasting
circumstance.
27
Stereo/Dual Reception
TIME settings
When a programme is selected, the sound information for the station
appears with the programme number and station name.
ENGLISH
Press I/II button to select the Multi Audio menu.
Broadcast
On Screen Display
Mono
MONO
Stereo
STEREO
Dual
1 Press SETTINGS and the Navigation buttons to scroll to TIME.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
TIME
DUAL I , DUAL II , DUAL I + II
NICAM
BTSC
BACK
* Image shown may differ from your TV.
Move
OK
Clock
NICAM
Off Time
: Off
On TIme
: Off
SAP
Sleep Timer
: Off
Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to
mono. In mono reception, the clarity of sound is improved.
Language selection for dual language broadcast
If a programme can be received in two languages (dual
language), you can switch to DUAL I, DUAL II or DUAL I+II.
DUAL I
Sends the primary broadcast language to the
loudspeakers.
DUAL I I
Sends the secondary broadcast language to the
loudspeakers.
DUAL I+I I
Sends a separate language to each loudspeaker.
The available time settings are described in the following.
Setting
Clock
NOTE
Nicam Reception
If the TV is equipped with a receiver for NICAM reception, high quality
NICAM (Near Instantaneous Companding Audio Multiplex) digital sound
can be received.
1 When NICAM mono is received, you can select NICAM MONO or
FM MONO.
2 When NICAM stereo is received, you can select NICAM STEREO or
FM MONO.
If the stereo signal is weak, switch to FM MONO.
3 When NICAM dual is received, you can select NICAM DUAL I,
NICAM DUAL II or NICAM DUAL I+II or FM MONO.
28
Sets the time.
Sets the time to turn on or off the TV
automatically. To use this function, you should
set the current time and date in advance.
Off Time /
On Time
Sound output can be selected according to the type of broadcast
received.
Description
Sleep Timer
• If you do not press any button within 2
hours after the TV turns on by the On Time
feature, the TV enters the Standby mode
automatically.
• If you set both Off Time and On Time
features to the same time, the Off Time
feature overrides the On Time feature.
Sets the length of time until the TV to turns off.
When you turn the TV off and turn it on again,
the Sleep Timer feature will be set to off.
LOCK settings
1 Press SETTINGS and the Navigation buttons to scroll to OPTION.
1 Press SETTINGS and the Navigation buttons to scroll to LOCK.
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
3 When you return to the previous menu, press
BACK.
* Image shown may differ from your TV.
OPTION
BACK.
* Image shown may differ from your TV.
Move
Menu Language
ENGLISH
OPTION settings
: English
OK
ꔉ
LOCK
Move
Lock System
OK
: Off
Input Label
Set Password
Factory Reset
Block Programme
Mode Setting
Input Block
The available option settings are described in the following.
The available lock settings are described in the following.
Setting
Menu Language
Input Label
Description
Selects a desired language.
Indicates which device is connected to which
input port.
Setting
Description
Lock System
Activates or deactivates the lock system.
Set Password
Changes the 4-digit password. The
default PIN is “0 0 0 0”.
Customizes the TV settings to suit your
preference. The initial setup screen will
appear when you turn on the TV for the
first time.
Factory Reset
Mode Setting
Home Use
Selects it for the Home
environment.
Store Demo
Selects it for the retail
environment.
Block Programme
Input Block
Blocks the programmes that contain
inappropriate contents for children
by pressing the Blue button. The Lock
icon appears in front of the blocked
programmes. The programmes can be
selected but the screen blank and the
audio is muted.
Blocks the input sources.
Selecting the Standard or Store Demo
environment. Choose the setting mode you
want.
29
USB settings
Teletext
1 Press SETTINGS and the Navigation buttons to scroll to USB.
ENGLISH
2 Press the Navigation buttons to scroll to the setting or option you
want and press OK .
3 When you return to the previous menu, press
BACK.
* Image shown may differ from your TV.
USB
Move
OK
Photo List
Music List
Movie List
* This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives upto-the minute information on news, weather, television programmes,
share prices and many other topics.
The teletext decoder of this TV can support the SIMPLE and FASTEXT
systems. SIMPLE (standard teletext) consists of a number of pages
which are selected by directly entering the corresponding page number.
FASTEXT are more modern methods allowing quick and easy selection
of teletext information.
DivX(R) VOD
Switch On/Off
Press the TEXT button to switch to teletext. The initial page or last page
viewed appears on the screen.
The available usbsettings are described in the following.
Two page numbers, TV station name, date and time are displayed on the
screen headline. The first page number indicates your selection, while
the second shows the current page displayed.
Setting
Description
Photo List
Views image files(photos) on TV which
are stored on USB device. (See p. 20)
Music List
Plays back music files on TV which are
stored on USB device. (See p. 20)
Simple text
Movie List
Plays movie files on TV which are
stored on usb device. (See p. 21)
Page selection
DivX(R) VOD
Views the registration code of your TV.
(See p. 24)
Press the TEXT button to switch off teletext. The previous mode
reappears.
1 Enter the desired page number as a three digit number with the
Number buttons. If during selection you press a wrong number, you
must complete the three digit number and then re-enter the correct
page number.
button can be used to select the preceding or
2 The
following page.
Fastext
The teletext pages are colour coded along the bottom of the screen and
are selected by pressing the corresponding coloured button.
Page selection
1 Press the INDEX button to select the index page.
2 You can select the pages which are colour coded along the bottom
line with corresponding coloured buttons.
3 AS with SIMPLE teletext mode, you can select a page by entering its
three digit page number with the Number buttons in FASTEXT mode.
4 The
button can be used to select the preceding or
following page.
30
Special teletext function
Troubleshooting
Cannot control the TV with the remote control.
Select the each index page.
Time
When viewing a TV programme, select this menu to display the time at
the top right hand corner of the screen.
In the teletext mode, press this button to select a sub page number. The
sub page number is displayed at the bottom of the screen. To hold or
change the sub page, press the Red/Green or Number buttons.
ENGLISH
Index
• Check the remote control sensor on the product and try again.
• Check if there is any obstacle between the product and the remote
control.
• Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
• Check if the product is turned on.
• Check if the power cord is connected to a wall outlet.
• Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
Hold
Stops the automatic page change which will occur if a teletext page
consists of 2 or more sub pages.
The number of sub pages and the sub page displayed is, usually, shown
on the screen below the time. When this menu is selected the stop
symbol is displayed at the top left-hand corner of the screen and the
automatic page change is inactive.
Reveal
Select this menu to display concealed information, such as solutions to
riddles or puzzles.
• Check the power control settings. The power supply may be
interrupted.
• Check if the Automatic Standby (Depending on model) / Sleep
Timer / Off Time is activated in the TIME settings.
• If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is
displayed.
• Turn the TV off/on using the remote control.
• Reconnect the HDMI cable.
• Restart the PC with the TV on.
Update
Displays the TV picture on the screen while waiting for a new teletext
page. The display will appear at the top left hand corner of the screen.
When the updated page is available then display will change to the
page number. Select this menu again to view the updated teletext
page.
31
Specifications
ENGLISH
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Environment condition
Analogue TV (Depending on Country)
Television system
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
Programme coverage
V/UHF : 1-69
Cable : 1-47
Maximum number of storable programmes
130
External antenna impedance
75 Ω
Component port connecting information
HDMI-DTV supported mode
NO
Resolution
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
640*480p
640*480p
720*480p
720*480p
1280*720p
1280*720p
720(1440)*480i
720(1440)*480i
720*576p
1280*720p
720(1440)*576i
1920*1080i
1920*1080i
1920*1080i
1920*1080p
1920*1080p
1920*1080p
1920*1080p
1920*1080p
1920*1080p
1920*1080p
H-freq.(kHz)
31.47
31.5
31.47
31.50
44.96
45.00
15.73
15.75
31.25
37.5
15.63
28.125
33.72
33.75
26.97
27.00
33.716
33.75
56.25.
67.432
67.50
V-freq.(Hz)
59.94
60.00
59.94
60.00
59.94
60.00
59.94
60.00
50.00
50.00
50.00
50.00
59.94
60.00
23.976
24.00
29.976
30.00
50.00
59.94
60.00
HDMI-PC supported mode
32
No
Resolution
H-freq.(kHz)
V-freq.(Hz)
1
2
3
4
5
6
720*400
640*480
800*600
1024*768
1360*768
1366*768
31.469
31.469
37.879
48.363
47.712
48.0
70
59.940
60.310
60.000
60.015
60
Component ports on the TV
Video output ports on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i / 576i
O
480p / 576p
O
720p / 1080i
O
1080p
O
(Only 50 Hz / 60 Hz )
Component input (Y, CB/PB, CR/PR)
NO
1
2
3
4
5
6
7
8
9
10
Resolution
720*480i
720*480p
1440*576i
720*576P
1280*720p
1280*720p
1920*1080i
1920*1080i
1920*1080p
1920*1080p
H-freq.(kHz)
15.73
31.50
16.63
31.50
37.50
45.00
28.13
33.75
56.25
67.50
V-freq.(Hz)
60.00
60.00
50.00
50.00
50.00
60.00
50.00
60.00
50.00
60.00
Environmental Information
(India region only)
ENGLISH
Disposal of your old appliance (as per e-waste Rules)
1. When this crossed out wheeled bin symbol is depicted on the product and its operator’s manual, it means the product is
covered by the e-waste Management and Handling Rules, 2011 and are meant to be recycled, dismantled, refurbished or
disposed off.
2. Dos
a. The product is required to be handed over only to the authorized recycler for disposal.
b. Keep the product in isolated area, after it becomes non-functional/un-repairable so as to prevent its accidental breakage.
Don’t
a. The product should not be opened by the user himself/herself, but only by authorized service personnel.
b. The product is not meant for re-sale to any unauthorized agencies/scrap dealer/kabariwalah.
c. The product is not meant for mixing into household waste stream.
d. Do not keep any replaced spare part(s) from the product in exposed area.
3. Any disposal through unauthorized agencies/person will attract action under Environment (Protection) Act 1986.
4. Hazards of improper handling or accidental breakage:
a. All picture tubes are hazardous due to concentration of lead, cadmium and zinc in it. The various chemicals and heavy metals contained in
picture tubes cause cancer, birth defects, hormone disruption, and damage body organs when they leak into the environment. All of this can, and
does, leach into the soil, ground water, air and our own bodies.
To prevent possible injury in case of breakage, wear heavy protective clothing, including gloves & safety goggles.
b. If batteries are disposed incorrectly, it can greatly harm the environment. The chemical by-products are hazardous. The metals and chemicals
found in batteries can mix into soil which may be hazardous to humans, plants and animals. If thrown in fire, they can cause blast and release toxic
gases which may be harmful for health.
5. To locate a nearest collection centre or call for pick-up (limited area only) for disposal of this appliance, please contact Toll Free No. 1800-180-9999
for details. All collection centre and pick up facilities are done by third parties whith LG Electronics India Pvt. Ltd. merely as a facilitator. For more
detailed information, please visit : http://www.lge.com/in
33
ENGLISH
35
Record the model number and serial number
of the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
MODEL
SERIAL
HDA71L3230I B
Download PDF