LG | HT355SD | LG HT355SD-F2 Owner’s Manual

OWNER’S MANUAL
DVD Receiver System
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
HT355SD (HT355SD, SH35SD-S/W)
P/NO : MFL63284753
HT355SD-F2_BPHLLL_ENG_4753.indd 1
2010-03-17 ¿ÀÈÄ 6:49:27
1
Safety Information
Safety Information
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK) NO USERSERVICEABLE PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the cord
exits the appliance. To disconnect power from the
mains, pull out the mains cord plug. When installing
the product, ensure that the plug is easily accessible.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
HT355SD-F2_BPHLLL_ENG_4753.indd 2
2010-03-17 ¿ÀÈÄ 6:49:27
Safety Information
Copyrights
Safe way to remove the battery or the battery
from the equipment:
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent
copyrighted material without permission. This
product features the copy protection function
developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and
playing the pictures of these discs picture noise
will appear. This product incorporates copyright
protection technology that is protected by U.S.
patents and other intellectual property rights. Use
of this copyright protection technology must be
authorized by Macrovision, and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
Remove the old battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put in the appropriate
container at designated collection points. Do not
dispose of batteries or battery together with other
waste. It is recommended that you use local, free
reimburse ment system batteries and accumulators.
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
1
Safety Information
This device is equipped with a portable battery or
accumulator.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION
’ OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
HT355SD-F2_BPHLLL_ENG_4753.indd 3
2010-03-17 ¿ÀÈÄ 6:49:27
Contents
1
16
Safety Information
1
2
3
4
5
16
LANGUAGE
CAUTION
17
DISPLAY
3
Copyrights
17
AUDIO
18
5.1 Speaker Setup
18
LOCK (Parental Control)
19
OTHERS
2
Preparation
6
Unique Features
6
Accessories
6
Playable Discs
Operation
7
Playable file Requirement
20
Basic Operations
9
Front panel
21
Other Operations
9
Rear panel
21
Displaying Disc Information on-
10
Remote Control
21
To display the DVD Menu
21
To display the DVD Title
21
Selecting a subtitle language
21
1.5 times speed playback
22
Starting play from selected
Installation
12
12
Connecting the speakers
Attaching the speakers to the
unit
6
12
13
7
Menu
2
3
To display and exit the Setup
Positioning the System
Connections to Your TV
13
Component Video Connection
14
Video Connection
14
4
screen
time
22
Last Scene Memory
22
Changing the character set to
display DivX® subtitle correctly
22
Programmed Playback
Optional Equipment Connection
14
AUX IN Connection
14
AUDIO IN (Portable IN)
Connection
15
USB Connection
15
Antenna Connection
16
16
Adjust the Setup settings
OSD Initial language settings
- Optional
HT355SD-F2_BPHLLL_ENG_4753.indd 4
2010-03-17 ¿ÀÈÄ 6:49:27
Contents
23
Viewing a PHOTO file
23
Viewing photo files as a slide
show
5
Maintenance
1
Listening to music during slide
27
show
27
When shipping the Unit
23
Sleep Timer Setting
27
Keeping the exterior surfaces
24
Dimmer
24
Turn off the sound temporarily
27
Cleaning the Unit
24
Screen Saver
27
Maintaining the Unit
24
System Select - Optional
27
24
Displaying file information
27
Handling Discs
(ID3 TAG )
27
Storing Discs
Radio Operations
27
Cleaning Discs
23
24
24
Listening to the Radio
24
Presetting the Radio Stations
25
Deleting all the saved stations
25
Improving poor FM reception
25
25
26
26
26
Sound adjustment
Setting the surround mode
Advanced Operations
Handling the Unit
clean
Notes on Discs
6
Troubleshooting
28
2
3
4
Troubleshooting
7
5
Listening to music from your
Appendix
portable player or external device
29
Language Codes
Recording to USB
30
Area Codes
31
Specifications
6
7
HT355SD-F2_BPHLLL_ENG_4753.indd 5
2010-03-17 ¿ÀÈÄ 6:49:28
Preparation
2
Preparation
2
Unique Features
Preparation
Portable In
Listens to music from your portable device.
(MP3, Notebook, etc)
USB Direct Recording
Records music from CD to your USB device.
Accessories
Please check and identify the supplied
accessories.
FM Antenna (1)
Remote Control (1)/
Battery (1)
Playable Discs
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CDRW/CD-R cannot be played on this unit due to
the recording quality or physical condition of
the disc, or the characteristics of the recording
device and authoring software.
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and finalized only.
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only.
DVD VR format that have been
finalized can not be played in this
unit
DVD+R: Video mode only.
Supports the double layer disc
also
DVD+RW (8 cm / 12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can
be purchased.
Video Cable (1)
HT355SD-F2_BPHLLL_ENG_4753.indd 6
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under license from Dolby
Laboratories.
2010-03-17 ¿ÀÈÄ 6:49:28
Preparation
About the  Symbol Display
“  ” may appear on your TV display during
operation and indicates that the function
explained in this owner’s manual is not
available on that disc.
Symbol Used in this Manual
Playable file
Requirement
MP3/ WMA music file requirement
MP3/ WMA file compatibility with this unit is
limited as follows :
ALL
MP3 files MP3
DVD and finalized DVD±R/RW DVD
WMA files WMA
DivX files DivX
Audio CDs ACD
• Maximum files : Under 999
JPG files
JPG
• File extensions : “.mp3”/ “.wma”
Regional Codes
This unit has a regional code printed on the
rear of the unit. This unit can play only DVD
discs labeled same as the rear of the unit or
“ALL”.
• Most DVD discs have a globe with one or
more numbers in it clearly visible on the
cover. This number must match your unit’s
regional code; or the disc cannot play.
• If you try to play a DVD with a different
regional code from your unit, the message
“Check Regional Code” appears on the TV
screen.
• Sampling frequency : between 32 to 48 kHz
(MP3), between 32 to 48 kHz (WMA)
• Bit rate : between 32 to 320 kbps (MP3), 40
to 320 kbps (WMA)
• Support Version : v2, v7, v8, v9
2
Preparation
All discs and file listed below • CD-ROM file format : ISO9660/ JOLIET
• We recommend that you use Easy-CD
Creator, which creates an ISO 9660 file
system.
Photo file requirement
JPEG disc compatibility with this unit is limited
as follows :
• Max pixel in width : 2 760 x 2 048 pixel
• Maximum files : Under 999
• Some discs may not operate due to a
different recording format or the condition
of disc.
• File extensions: “.jpg”
• CD-ROM file format : ISO9660/ JOLIET
HT355SD-F2_BPHLLL_ENG_4753.indd 7
2010-03-17 ¿ÀÈÄ 6:49:28
Preparation
DivX file requirement
DivX file compatibility with this unit is limited
as follows :
• Available resolution: up to 720x576 (W x H)
pixels.
• The file name of the DivX subtitle should be
45 characters or less.
2
Preparation
• If there is a code impossible to express in
the DivX file, it may be displayed as a “ _ ”
mark on the display.
• Frame rate : less than 30 fps
• If the video and audio structure of recorded
files are not interleaved, either video or
audio is output.
• Playable DivX file : ".avi", ".mpg", ".mpeg",
".divx"
• Playable Subtitle format : SubRip (*.srt/
*.txt), SAMI (*.smi), SubStation Alpha (*.ssa/
*.txt), MicroDVD (*.sub/ *.txt), SubViewer 2.0
(*.sub/ *.txt)
• Playable Codec format : "DIVX3.xx", "DIVX4.
xx", "DIVX5.xx", "MP4V3", "3IVX".
• Playable Audio format : "AC3", "PCM", "MP3",
"WMA".
• For Discs formatted in Live file system, you
can not play it on this player.
• If the name of a movie file is different from
that of the subtitle file, during playback of a
DivX file, the subtitle may not be displayed.
Compatible USB Devices
• MP3 Player : Flash type MP3 player.
• USB Flash Drive :Devices that support
USB 2.0 or USB 1.1.
• The USB function of this unit does not
support some USB devices.
USB device requirement
• Devices which require additional program
installation connected to a computer, are
not supported.
• Do not extract the USB device while in
operation.
• For a large capacity USB, it may take longer
than a few minute to be searched.
• To prevent data loss, back up all data.
• If you use a USB extension cable or USB
hub, the USB device is not recognized.
• Using NTFS file system is not supported.
(Only FAT(16/32) file system is supported.)
• This unit is not supported when the total
number of files is 1 000 or more.
• External HDD, Card readers, Locked devices, or hard type USB devices are not supported.
• USB port of the unit cannot be connected
to PC. The unit can not be used as a storage
device.
• If you play a DivX file different from the DivX
spec, it may not operate normally.
HT355SD-F2_BPHLLL_ENG_4753.indd 8
2010-03-17 ¿ÀÈÄ 6:49:28
Preparation
Front panel
a
b c d
efg
2
l
kj i h
T
UNING
(-/+)(.>),
Skip/Search
h
You can search by pressing and holding
TUNING.
b Power (1/ ))
c Open/Close (Z)
Preparation
a DVD/CD Disc Drawer
i MIC 1, 2
d Display window
e Play/Pause (B/X), MONO/ST.
f Stop (x)
g Function (F)
Selects the function or input source.
SB port
jU
You can play video, image and sound files
by connecting the USB device.
k P.(Portable) IN port
You can enjoy music from portable device
on your unit.
l Volume (VOL.)
Rear panel
a
b
c
de
f
a Power cord.
e AUX connector
b Speaker terminal
f COMPONENT VIDEO OUT (Y PB PR)
Connect to a TV with Y Pb Pr inputs.
c ANTENNA connector (FM)
d VIDEO OUT connector
Connect to a TV with video inputs.
HT355SD-F2_BPHLLL_ENG_4753.indd 9
2010-03-17 ¿ÀÈÄ 6:49:28
10
Preparation
Remote Control
SLEEP : Sets the system to turn off
automatically at a specified time. (Dimmer :
The display window will be darken by half.)
POWER : Switches the unit ON or OFF.
OPEN/CLOSE : Opens and closes the disc
Drawer.
Remote control
2
TITLE : If the current DVD title has a menu, the
title menu appears on the screen. Otherwise,
the disc menu may not appear.
a
Preparation
• • • • • • • • • b• • • • • • • • • •
DISPLAY : Accesses On-Screen Display.
MENU : Accesses the menu on a DVD disc.
b
SETUP : Accesses or removes setup menu.
PRESET (Uu) : Selects programme of Radio.
TUN. (-/+) : Tunes in the desired radio station.
U/u/I/i (up/ down/ left/ right): Used to
navigate on-screen displays.
c
ENTER : Acknowledges menu selection.
ylwlh{
RETURN (O) : Moves backwards in the menu
or exits the setup menu.
yhukvt
REC (z) : USB Direct Recording.
d
• • • • • • • • • c• • • • • • • • • •
STOP (x) : Stops playback or recording.
PLAY (B), MO./ST. : Starts playback. Selects
Mono/ Stereo.
e
PAUSE/STEP (X) : Pauses playback.
f
Q
• • • • • • • • • a• • • • • • • • •
SKIP (. / >) : Goes to next or previous
chapter/ track/ file.
SCAN (bb/BB) : Searches backward or
forward.
FUNCTION : Selects the function and input
source. (DVD/CD, USB, AUX, PORTABLE, FM,)
HT355SD-F2_BPHLLL_ENG_4753.indd 10
2010-03-17 ¿ÀÈÄ 6:49:29
Preparation
11
EQ (EQUALIZER effect) : Chooses sound
impressions.
Remote control
CLEAR : Removes a track number on the
Program List.
a
SUBTITLE : During playback, press SUBTITLE
repeatedly to select a desired subtitle language .
0 to 9 numerical buttons : Selects numbered
options in a menu.
• • • • • • • • • e • • • • • • • • •
TV Control buttons : Controls the TV. (LG TV
only)
Preparation
b
2
Controlling the TV
You can control the sound level, input
source, and power switching of LG TVs as
well. Hold POWER (TV) and press PR/CH
(+/–) button repeatedly until the TV turns
on or off.
c
ylwlh{
yhukvt
PROG./MEMO. : Accesses or removes Program
menu.
d
• • • • • • • • • f • • • • • • • • •
MIC VOL. : Adjusts microphone volume.
ECHO VOL. : Adjusts echo volume.
e
: This button is not available.
Put the battery into the remote control
f
Q
• • • • • • • • • d • • • • • • • • •
Make sure for the + (plus) and – (minus) on
the battery to be matched on the remote
control.
REPEAT/RANDOM : Selects a play
mode.(Random, repeat)
MUTE : Mutes the sound.
VOL (Volume) (+/-) : Adjusts speaker volume.
LG EQ : Selects a Natural or Local Specialization
equalizer effect by using LG EQ.
HT355SD-F2_BPHLLL_ENG_4753.indd 11
2010-03-17 ¿ÀÈÄ 6:49:29
12
Installation
3
Installation
Connecting the
speakers
3
Installation
Attaching the speakers to the
unit
To connect the cable to the unit, press each
plastic finger pad to open the connection
terminals on the unit. Insert the wire and
release the finger pad.
Connect the black end of each wire to the
terminals marked - (minus) and the other end
to the terminals marked + (plus).
Speaker connection
Positioning the System
The following illustration shows an example of
positioning the system.
Note that the illustrations in these instructions
differ from the actual unit for explanation
purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position (A).
A Front left speaker (L)/ B Front right speaker
(R):
Place the front speakers to the sides of the
monitor or screen and as flush with the
screen surface as possible.
C Center speaker: Place the center speaker
above or below the monitor or screen.
D Surround left speaker (L)/ E Surround right
speaker (R):
Place these speakers behind your listening
position, facing slightly inwards.
CAUTION
• Be careful to make sure children not to put their
hands or any objects into the *speaker duct.
*Speaker duct: A hole for plentiful bass sound
on speaker cabinet (enclosure).
F Subwoofer: The position of the subwoofer
is not so critical, because low bass sounds
are not highly directional. But it is better
to place the subwoofer near the front
speakers. Turn it slightly toward the center
of the room to reduce the wall reflections.
G Unit.
• The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far away
from either TV screen or PC monitor.
HT355SD-F2_BPHLLL_ENG_4753.indd 12
2010-03-17 ¿ÀÈÄ 6:49:29
Installation
Speaker Positioning
CAUTION
• Make sure the unit is connected directly to
the TV. Tune the TV to the correct video input
channel.
B
C
A
• Do not connect your unit via your VCR. The
image could be distorted by the copy
G
F
A
A
A
A
D
13
E
A
If the picture on nearby TV sets becomes
magnetically distorted, keep the speaker away
from your TV
Connect the COMPONENT VIDEO
(PROGRESSIVE SCAN) OUTPUT jacks on the unit
to the corresponding input jacks on the TV
using Y Pb Pr cables.
You can hear the sound through the system’s
speakers.
Component Video Connection
3
Installation
NOTE
Component Video Connection
Connections to Your
TV
Make one of the following connections,
depending on the capabilities of your existing
equipment.
NOTE
• Depending on your TV and other equipment
you wish to connect, there are various ways you
could connect the player. Use only one of the
connections described in this manual.
NOTE
If your TV accepts progressive format signals, you
must use this connection and set [Progressive
Scan] in [Display] setup to [On] (See page 17).
• Please refer to the manuals of your TV, Stereo
System or other devices as necessary to make
the best connections.
HT355SD-F2_BPHLLL_ENG_4753.indd 13
2010-03-17 ¿ÀÈÄ 6:49:30
14
Installation
Video Connection
Connect the VIDEO OUT (MONITOR) jack on
the unit to the video in jack on the TV using a
video cable.
You can hear the sound through the
system’s speakers.
Video Connection
3
Optional Equipment
Connection
AUX IN Connection
Connect an Output of auxiliary device to the
AUX Input (L/R) Connector.
If your TV has only one output for audio
(mono), connect it to the left (white) audio jack
on the unit.
AUX IN Connection
Installation
AUDIO IN (Portable IN)
Connection
Connect an OUTPUT of portable device (MP3
or PMP etc) to the P. IN input connector.
AUDIO IN Connection
MP3 player, etc...
HT355SD-F2_BPHLLL_ENG_4753.indd 14
2010-03-17 ¿ÀÈÄ 6:49:30
Installation
USB Connection
Antenna Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the
unit.
Connect the supplied FM antenna for listening
to the radio.
USB Connection
15
Connect the FM Wire antenna to the FM
antenna connector.
Antenna Connection
3
Installation
Removing the USB Device from the unit
1.Choose a different function mode or
press STOP (x) twice in a row.
2. Remove the USB device from the unit.
HT355SD-F2_BPHLLL_ENG_4753.indd 15
NOTE
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it as
horizontal as possible.
2010-03-17 ¿ÀÈÄ 6:49:31
16
Installation
Adjust the Setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and
the Setup menu, among other things. For details
on each Setup menu item, see pages 16 to 19.
To display and exit the Setup
Menu
1. Select the DVD/CD or USB function by
pressing FUNCTION.
2. Press SETUP.
Displays the [SETUP] Menu.
3. Press SETUP or RETURN to exit in the
[SETUP] Menu.
About help menu for Setup
3
Installation
OSD Initial language settings Optional
During the first use of this unit, the initial
language setup menu appears on your TV
screen. You must complete initial language
selection before using the unit. English will be
selected as the initial language.
1. Press POWER to turn the unit on. The
language setup menu will appear on the
screen.
Menu
Buttons
Operation
v/V
Move
Uu
Moving to another
menu.
b
<
Moving to previous
level.
>
Moving to next
level or selecting
menu.
Prev.
B
Select
O
RETURN
To exit the [Setup]
menu or [ 5.1
Speaker Setup].

ENTER
To confirm menu.
LANGUAGE
2. Use U u I i to select a language then
press ENTER.
The confirm menu will appear.
3. Use I i to select the [Enter] then press
ENTER to finish the language setup.
Menu Language
Select a language for the Setup menu and
then on screen display.
Disc Audio / Disc Subtitle / Disc
Menu
Select the language you prefer for the audio
track (disc audio), subtitles, and the disc menu.
Original – Refers to the original language in
which the disc was recorded.
HT355SD-F2_BPHLLL_ENG_4753.indd 16
2010-03-17 ¿ÀÈÄ 6:49:31
Installation
Other – To select another language, press
numeric buttons and then ENTER to enter the
corresponding 4-digit number according to
the language code list on the page 29. If you
enter the wrong language code, press CLEAR.
Off (for Disc Subtitle) – Turn off Subtitle.
DISPLAY
five seconds. The video output will be restored
to the standard setting, and a picture will be
visible on your TV.
AUDIO
DRC (Dynamic Range Control)
Select which screen aspect to use based on
the shape of your TV screen.
Vocal
4:3 – Select when a standard 4:3 TV is
connected.
Select [On] to mix karaoke channels into
normal stereo.
16:9 – Select when a 16:9 wide TV is
connected.
This function is effective for multi-channel
karaoke DVDs only.
Display Mode
Semi Karaoke
Letterbox – Displays a wide picture with
bands on the upper and lower portions of the
screen.
Panscan – Automatically displays the wide
picture on the entire screen and cuts off
the portions that do not fit. (If the disc/file is
not compatible with Pan Scan, the picture is
displayed at Letterbox ratio.)
Progressive Scan (For Component
Video connections)
Selects whether the COMPONENT
VIDEO(PROGRESSIVE SCAN) OUTPUT jacks
output progressive signal. If your TV accepts
progressive format signals, you will enjoy
accurate color reproduction and high quality
image by selecting [On]. If your TV does not
accept progressive format signals, select [Off ].
If you set Progressive Scan to [On] in error,
you must reset the unit. First, remove the disc
from the unit. Next, press and hold STOP for
HT355SD-F2_BPHLLL_ENG_4753.indd 17
3
Installation
TV Aspect
Make the sound clear when the volume is
turned down (Dolby Digital only). Set to [On]
for this effect.
The Display Mode setting works only when the
TV Aspect mode is set to 4:3.
17
When a chapter/ title/ track is fully finished, this
function shows the score in the screen with a
fanfare sound.
On – When you finished singing a score will
appear on the screen.
Off – Fanfare and score do not appears on the
screen.
NOTE
• DVD, DVD Karaoke discs with more than
2 tracks are available discs for the this function.
• When you watch movies, “off ” the Semi
Karaoke at the SETUP menu or enjoy it without
connecting the MIC if the fanfare or score
appears during changing a chapter.
2010-03-17 ¿ÀÈÄ 6:49:31
18
Installation
5.1 Speaker Setup
Make the following settings for the built-in 5.1
channel surrounds decoder.
1. Press SETUP.
2. Use U u to select AUDIO menu and then
press i.
3. Use U u to select [5.1 Speaker setup] menu
and then press i.
4. Press ENTER
The [5.1 Speaker setup] appears.
3
Size – Since the speaker settings are fixed, you
cannot change the settings.
Volume – Press I i to adjust the output level
of the selected speaker.
Installation
Distance – After you connected speakers
to your unit, set the Distance between the
speakers and your listening point if the
distance of Center or Rear speakers is bigger
than the distance of Front speakers. This allows
the sound from each speaker to reach the
listener at the same time. Press I i to adjust
the Distance of the selected speaker. This
distance is equivalent to a difference of the
distance between Center or Rear speaker and
Front speakers.
Test – Press I i to test the signals of each
speaker. Adjust the volume to match the
volume of test signals memorized in the
system.
5. Use I i to select the desired speaker.
6. Adjust options using U u I i buttons.
LOCK (Parental Control)
7. Press RETURN to confirm your selection.
Return to the previous menu.
Initial Setting of the Area Code:
Speaker selection
Select a speaker that you want to adjust.
NOTE
Certain speaker settings are prohibited by the
Dolby Digital licensing agreement.
When you use this unit for the first time, you
have to set the Area Code.
1. Select the [LOCK] menu and then press i.
2. Press i.
To access the [LOCK] options, you must
input the password you have created. Input
a password and press ENTER. Enter it again
and press ENTER to verify. If you make
a mistake before pressing ENTER, press
CLEAR.
3. Select the first character using U u buttons.
4. Press ENTER and select the second
character using U u buttons.
5. Press ENTER to confirm your Area code
selection.
HT355SD-F2_BPHLLL_ENG_4753.indd 18
2010-03-17 ¿ÀÈÄ 6:49:31
Installation
Rating
Area Code
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
Enter the code of the area whose standards
were used to rate the DVD video disc, based
on the list on page 30.
1. Select [Rating] on the [LOCK] menu then
press i
2. Input a password and press ENTER.
3. Select a rating from 1 to 8 using the U u
buttons.
Rating 1-8 – Rating one (1) has the most
restrictions and rating eight (8) is the least
restrictive.
4. Press ENTER to confirm your rating
selection.
Password
You can enter or change password.
1. Select [Password] on the [LOCK] menu and
then press i.
2. Input a password and press ENTER..
To change the password, press ENTER
when the [Change] option is highlighted.
Input a password and press ENTER. Enter it
again and press ENTER to verify.
3. Press SETUP to exit the menu.
NOTE
1. Select [Area Code] on the [LOCK] menu
then press i.
2. Input a password and press ENTER.
3. Select the first character using U u buttons.
4. Press ENTER and select the second
character using U u buttons.
5. Press ENTER to confirm your Area code
selection.
3
Installation
Unlock – If you select unlock, parental
control is not active and the disc plays in
full.
19
OTHERS
DivX(R) VOD
We provide you with the DivX® VOD (Video On
Demand) registration code that allows you to
rent and purchase videos using the DivX® VOD
service.
For more information, visit www.divx.com/vod.
Press ENTER when [DivX(R) VOD] is highlighted
and you can view the registration code of the
unit.
NOTE
All the downloaded videos from DivX® VOD can
only be played back on this unit.
If you forget your password, you can clear it
using the following steps:
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number “210499” and press
ENTER. The password is cleared.
HT355SD-F2_BPHLLL_ENG_4753.indd 19
2010-03-17 ¿ÀÈÄ 6:49:31
20
Operation
4
Operation
Basic Operations
1. Insert the disc by Pressing OPEN/CLOSE or
connect the USB device to the USB port.
2. Select the DVD/CD or USB function by
pressing FUNCTION.
4
3. Select a file (or track/ title) you want to play
by pressing U u I i.
Operation
NOTE
.
When playing a disc or USB Flash Drive
containing with DivX, MP3/ WMA and JPEG files
together, you can select menu of files which you
would like to play by pressing MENU. If “This file
has non-supported type on the unit” pops up,
select an appropriate file by pressing MENU.
To
Do this
Stop
Press x
Playback
Press B
Pause
Frameby-Frame
playback
Press PAUSE/STEP
Press PAUSE/STEP
repeatedly to play title
Frame-by-Frame.
During playback, press .
or > to go to the next
Skipping to
chapter/track or to return to
the next/
the beginning of the current
previous
chapter/track.
chapter/ track/
Press . twice briefly to
file
step back to the previous
chapter/track.
Locating a
point quickly
by playing
a file in fast
forward or fast
reverse
During playback, press bb
or BB repeatedly to select
the required scan speed.
To return to normal speed,
press PLAY.
Playing
repeatedly or
randomly
Press REPEAT/RANDOM
repeatedly, and the current
title, chapter or track will be
played back repeatedly or
randomly.
- Random play mode : only
music files.
Slowing down In the pause mode, press
the playing SCAN (bb or BB) to select
speed
the required speed.
HT355SD-F2_BPHLLL_ENG_4753.indd 20
2010-03-17 ¿ÀÈÄ 6:49:31
Operation
Other Operations
Displaying Disc Information
on-screen
You can display various information about the
disc loaded on-screen.
1. Press DISPLAY to show various playback
information.
The displayed items differ depending on
the disc type or playing status.
2. You can select an item by pressing U u and
change or select the setting by pressing
I i.
Title – C
urrent title number/ total
number of titles.
DVD
When you play a DVD which contains several
menus, you can select the menu you want
using the Menu.
1. Press MENU.
The disc’s menu appears.
2. Select the menu by using U u I i.
3. Press PLAY to confirm.
To display the DVD Title
DVD
When you play a DVD which contains several
titles, you can select the title you want using
the Menu.
1. Press TITLE.
The disc’s title appears.
4
2. Select the menu by pressing
U u I i.
Operation
Chapter – Current chapter number/
total number of
chapters.
To display the DVD Menu
3. Press PLAY to confirm.
Time – Elapsed playing time.
Audio – Selected audio language
or channel.
Subtitle – Selected subtitle.
Angle – S elected angle/total
number of angles.
Sound – Selected sound mode
NOTE
If any button is not pressed for a few
seconds, the onscreen display disappears.
21
Selecting a subtitle language
DVD
DivX
During playback, press SUBTITLE(
)
repeatedly to select a desired subtitle
language.
1.5 times speed playback
DVD
The 1.5 speed allows you to watch the pictures
and listen to the sound quicker than playing at
a normal speed.
1. During playback, press PLAY(B ) to play
at 1.5 times speed. “BX1.5” appears on the
screen.
2. Press PLAY(B) again to exit.
HT355SD-F2_BPHLLL_ENG_4753.indd 21
2010-03-17 ¿ÀÈÄ 6:49:32
22
4
Operation
Starting play from selected
time DVD DivX
Programmed Playback
To start playing at any chosen time on the file
or title.
The program function enables you to store
your favourite files from any disc or USB device.
1. Press DISPLAY during playback.
A program can contain 30 tracks/files.
2. Press U u to select the time clock icon and
“--:--:--” appears.
1. Select the DVD/CD or USB function by
pressing FUNCTION.
3. Input the required start time in hours,
minutes, and seconds from left to right. If
you enter the wrong numbers, press CLEAR
to remove the numbers you entered. Then
input the correct numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by
using numerical buttons.
2. To add a music(s) on the program list, press
PROG./MEMO. to enter the program edit
mode (E mark appears on the menu).
4. Press ENTER to confirm. Playback starts
from the selected time.
Operation
Last Scene Memory
DVD
This unit memorizes the last scene from the
last disc that is viewed. The last scene remains
in memory even if you remove the disc from
the player or switch off (Stand-by mode) the
unit. If you load a disc that has the scene
memorized, the scene is automatically recalled
Changing the character set to
display DivX® subtitle correctly
DivX
ACD
MP3 WMA
3. Select a desired music on the [List] by using
the U u then press ENTER to add the
music to the program list.
4. Select music from the program list then
press ENTER to start programmed playback.
Erasing a file from Program List
1. Use U u to select the track that you wish to
erase from the Program list.
2. Press CLEAR.
Erasing the Complete Program List
Use U u I i to select [Clear All] then press
ENTER.
NOTE
The programs are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
If the subtitle does not display properly during
playback press and hold SUBTITLE for about
3 seconds then press I i or SUBTITLE to
select another language code until the subtitle
is displayed properly and then press ENTER.
HT355SD-F2_BPHLLL_ENG_4753.indd 22
2010-03-17 ¿ÀÈÄ 6:49:32
Operation
Viewing a PHOTO file
JPG
This unit can play discs with photo files.
1. Select the DVD/CD or USB function by
pressing FUNCTION.
2. Press U u to select a folder, and then press
ENTER.
A list of files in the folder appears.
If you are in a file list and want to return to
the previous folder list, use the U u buttons
on the remote to highlight
and press
ENTER.
3. If you want to view a particular file, press
U u to highlight a file and press ENTER or
PLAY. While viewing a file, you can press
STOP to move to the previous menu (JPEG
menu).
1. Highlight the file (not folder) which you like
beginning slide show.
2. Use U u I i to highlight the Speed. Then,
use I i to select the (>/ >>/ >>>) option
you want to use and then press ENTER.
3. Use U u I i to highlight the (Slide Show)
then press ENTER.
Listening to music during slide
show JPG
You can listen to music during slide show, if the
disc contain music and photo files together.
Use U u I i to highlight (
) icon then
press ENTER to start slide show.
NOTE
This function is available only in disc.
Sleep Timer Setting
Press SLEEP one or more times to select delay
time between 10 and 180 minutes, after the
unit will turn off.
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then
press SLEEP once again while “SLEEP 10” is
displayed.
4
Operation
Viewing photo files as a slide
show JPG
23
NOTE
You can check the remaining time before the
unit turns off.
About help menu for slide show
Menu
Buttons
Operation
v/V
U/u
Rotating the
picture
./ >
Prev./ Next
I/i
Moving to
another file
x
STOP
Closing the
slide show
O
RETURN
Closing the
help menu
HT355SD-F2_BPHLLL_ENG_4753.indd 23
2010-03-17 ¿ÀÈÄ 6:49:32
24
Operation
Dimmer
Press SLEEP once. The display window will
be darken by half. To cancel it, press SLEEP
repeatedly until dim off.
Radio Operations
Be sure that FM aerial is connected.
(Refer to the page 15)
Turn off the sound temporarily
Press MUTE to mute your unit.
Listening to the Radio
You can mute your unit, for example, to answer
the telephone, the “MUTE” displayed in the
display window.
1. Press FUNCTION until FM appears in the
display window.
The last received station is tuned in.
Screen Saver
2. Press and hold TUN.(-/+) for about two
seconds until the frequency indication
starts to change, then release. Scanning
stops when the unit tunes in a station.
The screen saver appears when you leave the
unit in Stop mode for about five minutes.
4
Operation
System Select - Optional
You must select the appropriate system mode
for your TV system. If “NO DISC” appears in the
display window, press and hold PAUSE/STEP
(X) for more than five seconds to be able to
select a system. (AUTO/ PAL/ NTSC)
or
Press TUN.(-/+) repeatedly.
3. Adjust the volume by rotating VOL. on the
front panel or by pressing VOL + or - on the
remote control repeatedly.
Presetting the Radio Stations
You can preset 50 stations for FM .
Displaying file information
(ID3 TAG )
While playing an MP3 file containing file
information, you can display the information
by pressing DISPLAY.
Before tuning, make sure that you have turned
down the volume.
1. Press FUNCTION until FM appears in the
display window.
2. Select the desired frequency by using
TUN.(-/+)
3. Press PROG./MEMO. a preset number will
flash in the display window.
4. Press PRESET (Uu) to select the preset
number you want.
5. Press PROG./MEMO.
The station is stored.
6. Repeat the steps 2 to 5 to store other
stations.
HT355SD-F2_BPHLLL_ENG_4753.indd 24
2010-03-17 ¿ÀÈÄ 6:49:32
Operation
Deleting all the saved stations
1. Press and hold PROG./MEMO. for two
seconds.
“ERASE ALL” will flash up on the unit display.
Description
AUTO EQ
Sets the sound equalizer to
the mode that is the most
similar to the genre which is
included in the MP3 ID3 tag
of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock pop, jazz or classic
concert.
MP3 OPT
This function is optimized
for compressible MP3 file. It
improves the treble sound.
BASS
During playback, Reinforces
the treble, bass and
surround sound effect.
VIRTUAL
You can enjoy more virtual
surround sound.
2. Press PROG./MEMO. to erase of the saved
radio stations.
Improving poor FM reception
Press PLAY (B) (MO./ST.) on the remote control.
This will change the tuner from stereo to mono
and usually improve the reception.
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound
mode by using EQ/ LG EQ. You can change
the EQ/ LG EQ using I i arrow key while the
EQ/ LG EQ information is displayed on.
The displayed items for the Equalizer may be
different depending on sound sources and
effects.
On Display
Description
PLII MOVIE
PLII MUSIC
BYPASS
Dolby Pro Logic II enables
you to play stereo source on
5.1-channel.
You can enjoy the sound
without equalizer effect.
NOTE
NAT PLUS
You can enjoy the natural
sound effect same as a
5.1-channel.
• In some of surround modes, on some
speakers, there’s no sound or low sound. it,
depends on the mode of surround and the
source of audio, it is not defective.
NATURAL
You can enjoy comfortable
and natural sound.
• You may need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
Regionally optimized
sound effect. (DANGDUT/
Local
ARABIC/ PERSIAN/ INDIA/
Specialization
REGUETON/ MERENGUE/
equalizer
SALSA/ SAMBA/ CUMBIA/
AFRO)
HT355SD-F2_BPHLLL_ENG_4753.indd 25
4
Operation
On Display
25
2010-03-17 ¿ÀÈÄ 6:49:32
26
Operation
Advanced Operations
Listening to music from your
portable player or external
device
4
• You can check the recording percentage rate
for the USB record on the screen during the
recording.
• When you stop recording during playback, the
file that has been recorded at that time will be
stored.
The unit can be used to play the music from
many types of portable player or external
devices. (Refer to the page 14)
• Do not remove the USB device during USB
recording. It will result in an incomplete file
being made and may not be deleted on a PC.
1. Connect the portable player to the
P. IN(PORTABLE IN) connector on the unit.
• If USB recording does not work, messages like
“NO USB”, “ERROR”, “USB FULL” or “NO REC” will
be displayed on the display window.
NOTE
Or
Connect the external device to the AUX
connector of the unit.
2 Turn the power on by pressing POWER.
Operation
3 Select the PORTABLE or AUX function by
pressing FUNCTION.
• When you stop recording during playback, the
file will not be stored.
• USB record is not possible from CD-G discs.
• You may not store more than 999 files.
• It’ll be stored as TRK_001 on CD FOLDER.
4 Turn the portable player or external device
and start it playing.
Recording to USB
1. Connect the USB device to the unit.
2. Select a DVD/ CD function by pressing
FUNCTION.
The making of unauthorized copies of copyprotected material, including computer programs,
files, broadcasts and sound recordings, may be
an infringement of copyrights and constitute a
criminal offense. This equipment should not be
used for such purposes.
Be responsible
Respect copyrights
One track recording - You can record to USB
after play you want file.
All tracks recording - You can record to USB
after stop.
Program list recording - After moving to
the programmed list and you can record it
to USB.
3 Start the recording by pressing z REC.
4 To stop recording, press x STOP.
HT355SD-F2_BPHLLL_ENG_4753.indd 26
2010-03-17 ¿ÀÈÄ 6:49:32
Maintenance
27
5
Maintenance
Handling the Unit
Notes on Discs
When shipping the Unit
Handling Discs
Please save the original shipping carton and
packing materials. If you need to ship the unit,
for maximum protection, re-pack the unit as it
was originally packed at the factory.
Never stick paper or tape on the disc.
Keeping the exterior surfaces
clean
• Do not use volatile liquids such as
insecticide spray near the unit.
Cleaning the Unit
To clean the unit, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth
lightly moistened with a mild detergent
solution.
Do not use strong solvents such as alcohol,
benzene, or thinner, as these might damage
the surface of the unit.
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause
poor picture quality and sound distortion.
Before playing, clean the disc with a clean
cloth. Wipe the disc from the center out.
Do not use strong solvents such as alcohol,
benzene, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.
5
Maintenance
• Wiping with strong pressure may damage
the surface. Do not leave rubber or plastic
products in contact with the unit for a long
period of time.
Storing Discs
Maintaining the Unit
The unit is a high-tech, precision device. If
the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality could be
diminished. For details, please contact your
nearest authorized service center.
HT355SD-F2_BPHLLL_ENG_4753.indd 27
2010-03-17 ¿ÀÈÄ 6:49:33
28
Troubleshooting
6
Troubleshooting
PROBLEM
No Power
No Picture
There is little or
no sound
CAUSE
CORRECTION
The power cord is disconnected.
Plug the power cord into the wall outlet securely.
The TV is not set to receive the DVD signal.
Select the appropriate video input mode on the
TV so the picture from the DVD Receiver appears
on the TV screen.
The video cables are not connected securely.
Connect the video cables securely to both the TV
and DVD Receiver.
Select the correct input mode of the audio
Equipment connected via the audio cable is not set
receiver so you can hear the sound from the DVD
to receive DVD signal output.
receiver.
The audio cables are not connected to the speakers Connect the audio cables into the connection
or receiver securely.
terminals correctly.
If not, connect speaker cables correctly.
6
Speaker cables connected correctly.
The DVD picture
The disc is dirty.
quality is poor
Clean the disc using a soft cloth with outward
strokes.
A DVD/CD will
not play
No disc is inserted.
Insert a disc.
An unplayable disc is inserted.
Insert a playable disc (check the disc type, colour
system and regional code).
The disc is inserted upside down.
Place the disc with the label or printed side facing
upwards.
The menu is open on screen.
Press SETUP to close the menu screen.
There is a parental lock which prevents the
playback of DVDs with a certain rating.
Enter your password or change the rating level.
Troubleshooting
Humming noise The disc is dirty.
heard while a
DVD or CD is
The DVD receiver is located too close to the TV,
playing
causing feedback.
Clean the disc using a soft cloth with outward
strokes.
Radio stations
can’t be tuned in The antenna is positioned or connected poorly.
properly
Check the antenna connection and adjust its
position.
Move DVD receiver and audio components
further away from your TV.
Attach an external aerial if necessary.
The signal strength of the radio station is too weak. Tune to the station manually.
No stations have been preset or preset stations
Preset some radio stations, see page 24 for
have been cleared (when tuning by scanning preset
details.
channels).
The remote is not pointed directly at the unit.
The remote
control doesn’t
work well / at all The remote is too far from the unit.
Point the remote directly at the unit.
Use the remote within 23 feet (7m) of the DVD
receiver.
There is an obstacle in the path between the
remote control and the unit.
Remove the obstacle.
The battery in the remote control is flat.
Replace the battery with new ones.
HT355SD-F2_BPHLLL_ENG_4753.indd 28
2010-03-17 ¿ÀÈÄ 6:49:33
Appendix
29
7
Appendix
Language Codes
Use this list to input your desired language for the following initial settings: Disc Audio, Disc
Subtitle, Disc Menu.
Code
Language Code
Language Code
Language Code
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
9072
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
French Frisian Galician Georgian German Greek Greenlandic Guarani Gujarati Hausa Hebrew Hindi Hungarian Icelandic Indonesian Interlingua Irish Italian Javanese Kannada Kashmiri Kazakh Kirghiz Korean Kurdish Laothian Latin Latvian, Lettish Lingala 7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
7678
Lithuanian Macedonian Malagasy Malay Malayalam Maori Marathi Moldavian Mongolian Nauru
Nepali Norwegian Oriya Panjabi Pashto, Pushto Persian Polish Portuguese Quechua Rhaeto-Romance Rumanian Russian Samoan Sanskrit Scots Gaelic Serbian Serbo-Croatian Shona Sindhi 7684
7775
7771
7783
7776
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Singhalese Slovak Slovenian Spanish Sudanese Swahili Swedish Tagalog Tajik Tamil Telugu Thai Tonga Turkish Turkmen Twi Ukrainian Urdu Uzbek Vietnamese Volapük Welsh Wolof Xhosa Yiddish Yoruba Zulu 8373
8375
8376
6983
8385
8387
8386
8476
8471
8465
8469
8472
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
HT355SD-F2_BPHLLL_ENG_4753.indd 29
Appendix
Language Afar Afrikaans Albanian Ameharic Arabic Armenian Assamese Aymara Azerbaijani Bashkir Basque Bengali; Bangla Bhutani Bihari Breton Bulgarian Burmese Byelorussian Chinese Croatian Czech Danish Dutch English Esperanto Estonian Faroese Fiji Finnish 7
2010-03-17 ¿ÀÈÄ 6:49:33
30
Appendix
Area Codes
Choose a area code from this list.
Appendix
Area Afghanistan Argentina Australia Austria Belgium Bhutan Bolivia Brazil Cambodia Canada Chile China Colombia Congo Costa Rica Croatia Czech Republic Denmark Ecuador Egypt El Salvador Ethiopia Fiji Finland France Germany Great Britain Greece Greenland Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
ET
FJ
FI
FR
DE
GB
GR
GL
Area Hong Kong Hungary India Indonesia Israel Italy Jamaica Japan Kenya Kuwait Libya Luxembourg Malaysia Maldives Mexico Monaco Mongolia Morocco Nepal Netherlands Netherlands Antilles New Zealand Nigeria Norway Oman Pakistan Panama Paraguay Philippines Code
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
LU
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
PY
PH
Area Poland Portugal Romania Russian Federation Saudi Arabia Senegal Singapore Slovak Republic Slovenia South Africa South Korea Spain Sri Lanka Sweden Switzerland Taiwan Thailand Turkey Uganda Ukraine United States Uruguay Uzbekistan Vietnam Zimbabwe Code
PL
PT
RO
RU
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
7
HT355SD-F2_BPHLLL_ENG_4753.indd 30
2010-03-17 ¿ÀÈÄ 6:49:33
Appendix
31
Specifications
General
Power supply Refer to main label.
Power consumption Refer to main label.
Net Weight 2.5 kg
External dimensions (W x H x D) 360 x 65 x 320 mm
500 mA
Bus Power Suply (USB)
DC 5 V
Operating conditions Temperature 5 °C to 35 °C,
Operation status: Horizontal
Operating humidity 5 % to 85 %
Laser Semiconductor laser,
wavelength 650 nm
Tuner FM
FM Tuning Range FM Intermediate Frequency
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
128 kHz
Amplifier
Stereo mode Surround mode Front
Center
Surround
Subwoofer
45 W + 45 W (4 Ω at 1 kHz, THD 10 %)
45 W + 45 W (THD 10 %)
45 W
45 W + 45 W (4 Ω at 1 kHz, THD 10 %)
75 W (8 Ω at 30 Hz, THD 10 %)
Front/Rear/Center Speaker
Passive Subwoofer
1 Way 1 Speaker
1 Way 1 Speaker
Impedance
4Ω
8Ω
Rated Input Power
45 W
75 W
Max. Input Power
90 W
150 W
103 x 111 x 94 mm
156 x 325 x 320 mm
0.39 kg
3.6 kg
Type
Net Dimensions (W x H x D)
Net Weight
Appendix
Speakers
7
Designs and specifications are subject to change without prior notice.
HT355SD-F2_BPHLLL_ENG_4753.indd 31
2010-03-17 ¿ÀÈÄ 6:49:33
HT355SD-F2_BPHLLL_ENG_4753.indd 32
2010-03-17 ¿ÀÈÄ 6:49:33
Download PDF