LG | FB166 | LG FB166 Owner’s Manual

OWNER’S MANUAL
DVD Micro Hi-Fi System
Please read this manual carefully before operating
your set and retain it for future reference.
FB166 (FB166, FBS166V)
P/NO : MFL67228232
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Copyrights
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent
copyrighted material without permission. This
product features the copy protection function
developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and
playing the pictures of these discs picture noise
will appear. This product incorporates copyright
protection technology that is protected by U.S.
patents and other intellectual property rights. Use
of this copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD
DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p UNIT, PLEASE CONTACT
OUR CUSTOMER SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
4
Table of Contents
Table of Contents
1
Getting Started
2
6
6
6
6
6
7
7
7
7
7
8
9
10
12
Safety Information
Unique Features
– Portable In
– USB Direct Recording
– Full HD up-scaling
Accessories
Introduction
– Playable Discs
– About the “7” Symbol Display
– Symbols Used in this Manual
– Regional Codes
Playable file Requirement
Remote control
Front panel
Rear panel
2
Connecting
13
13
14
14
15
16
16
16
16
16
Attaching the speakers to the unit
Connections to Your TV
– Component Video Connection
– HDMI Out Connection
– Video Connection
– Resolution Setting
Video Output Resolution
Optional Equipment Connection
– AUDIO (PORT. IN) In Connection
– Listening to music from your portable
player or external device
– USB Connection
– OPTICAL In connection
– Home theater speaker ez setup
– Antenna Connection
– Playing the iPod
– Compatible iPod
17
17
17
18
18
19
3
System Setting
20
20
Adjust the setup settings
– OSD Initial language settings Optional
– To display and exit the Setup menu
– Language
– Display
– Audio
– Lock (Parental Control)
– Others
20
21
21
22
22
23
Table of Contents
4
Operating
5
Troubleshooting
24
24
25
25
25
25
25
25
25
26
26
26
27
28
28
28
29
29
29
29
29
29
30
30
30
30
30
30
31
31
32
32
Using the Home Menu
Basic Operations
Other Operations
– Displaying Disc Information on-screen
– To display the DVD Menu
– To xdisplay the DVD title
– 1.5 times speed playback
– Screen Saver
– Starting play from selected time
– Resume playback
– Changing subtitle code page
– Marked Playback
– Viewing a PHOTO file
– Last Scene Memory
– System Select - Optional
– Adjust the speaker level settings
– Setting the Clock
– Using your player as an alarm clock
– Sleep Timer Setting
– Dimmer
– Turn off the sound temporarily
– DEMO
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Deleting a saved station
– Improving poor FM reception
Sound adjustment
– Setting the surround mode
Advanced Operations
– Recording to USB.
33
Troubleshooting
6
Appendix
34
35
36
37
39
39
39
Area Code List
Language code List
Trademarks and Licenses
Specifications
Maintenance
– Handling the Unit
– Notes on Discs
5
1
2
3
4
5
6
6
Getting Started
Unique Features
Accessories
Please check and identify the supplied accessories.
1
Portable In
Getting Started
Listens to music from your portable device. (MP3,
Notebook, etc)
USB Direct Recording
Records music from CD to your USB device.
Remote control (1)
Battery (1)
FM antenna (1)
Video cable (1)
Full HD up-scaling
Views Full HD picture quality with simple setup.
Getting Started
Introduction
Playable Discs
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and finalized only.
Symbols Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
y
Video files contained in the
USB/Disc
u
Audio files contained in the
USB/Disc
i
Photo files
, Note
Indicates special notes and operating features.
, Tip
Indicates tip and hints for making the task easier.
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only.
DVD+R: Video mode only
> Caution
Indicates cautions for preventing possible damages
from abuse.
Supports the double layer disc also.
DVD+RW (8 cm / 12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
About the “7” Symbol Display
“7” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or
“ALL”.
 Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
 If you try to play a DVD with a different regional
code from your unit, the message “Check
Regional Code” appears on the TV screen.
1
Getting Started
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CD-RW/
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc,
or the characteristics of the recording device and
authoring software.
7
8
Getting Started
Playable file
Requirement
DivX file requirement
DivX file compatibility with this unit is limited as
follows:
 Available resolution: within 800 x 600 (W x H)
pixels.
1
Getting Started
MP3/ WMA music file requirement
MP3/ WMA file compatibility with this unit is limited
as follows :
 Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
 Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
 Support Version : v2, v7, v8, v9
 Maximum files : Under 999
 File extensions : “.mp3”/ “.wma”
 The file name of the DivX subtitle should be
entered within 45 characters.
 If there is impossible code to express in the
DivX file, it may be displayed as “ _ “ mark on the
display.
 Frame rate : less than 30 fps.
 If the video and audio structure of recorded
files is not interleaved, either video or audio is
outputted.
 Playable DivX file : “.avi”, “.mpg”, “.mpeg”, “.divx”
 We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
 Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
Photo file requirement
 Playable Codec format : “DIVX3.xx”, “DIVX4.xx”,
“DIVX5.xx”, “MP4V3”, “3IVX”.
 CD-ROM file format : ISO9660/ JOLIET
Photo file compatibility with this unit is limited as
follows :
 Max pixel in width : 2 760 x 2 048 pixel
 Maximum files : Under 999
 Some discs may not operate due to a different
recording format or the condition of disc.
 File extensions: “.jpg”
 CD-ROM file format : ISO9660/ JOLIET
 Playable Audio format : “AC3”, “PCM”, “MP3”, “WMA”.
 Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
 Bit rate : within 32 to 320 kbps (MP3), 40 to 192
kbps (WMA)
 For Discs formatted in Live file system, you can
not it on this unit.
 If the name of movie file is different from that of
the subtitle file, during playback of a DivX file,
subtitle may not be display.
 If you play a DivX file differ from DivXspec, it may
not operate normally.
Getting Started
Remote control
• • • • • • a • • • • •
• • • • • • d • • • • •
P RADIO&INPUT: Changes
input sources.
SPEAKER LEVEL: Sets the sound
level of desired speaker.
MARKER: Marks play list.
SOUND EFFECT: Selects a sound
effect mode.
B OPEN/CLOSE: Ejects or insert
the disc from slot loader.
SLEEP: Sets the System to turn off
automatically at a specified time.
(Dimmer : The display window will
be darken by half.)
OPTICAL: Changes input source
to optical directly.
MUTE: Mutes the sound.
• • • • • • e • • • • •
m INFO/DISPLAY: Accesses OnScreen Display.
0-9 numerical buttons: Selects
numbered options in a menu.
n HOME: Displays the [Home
Menu].
CLEAR: Removes a number when
setting the password.
DISC MENU: Accesses the menu
on a DVD disc.
REPEAT: Selects a play mode.
(Repeat/ Random)
• • • • • • b • • • • •
• • • • • • f • • • • •
W/S/A/D (up/ down/ left/
right): Used to navigate on-screen
displays.
TV Control buttons: Controls the
TV. (LG TV only)
PRESET +/-: Selects programme
of Radio.
TUNING -/+: Tunes in the desired
radio station.
b ENTER: Acknowledges menu
selection.
Presetting the radio stations.
x RETURN: Moves backwards
in the menu or exits the setup
menu.
TITLE: If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
• • • • • • c • • • • •
C/V SKIP: Goes to the next
or previous chapter / track / file.
c/v SCAN: Searches
backward or forward.
Remove the battery cover on the
rear of the Remote Control, and
insert one (size AAA) battery with
4 and 5 matched correctly.
VOL +/- (Volume): Adjusts
speaker volume.
Z STOP: Stops playback.
d PLAY, MONO/STEREO: Starts
playback. Selects Mono/ Stereo.
M PAUSE/STEP: Pauses playback.
- You can control the sound lev
el, input source, and power
switching of LG TVs as well.
Hold POWER (TV) and press PR/
CH (+/-) button repeatedly until
the TV turns on or off.
X REC: USB Direct Recording.
?: This button is not available.
1
Getting Started
1 POWER: Switches the unit ON
or OFF.
Battery Installation
9
10
Getting Started
Front panel
1
Getting Started
Getting Started
a Disc Slot
b iPod dock
c 1/! (POWER)
Switches the unit ON or OFF.
e FUNC. (FUNCTION)
Changes the input source or function.
f USB Port
Connects an USB device.
g EQ
You can choose fixed sound impression.
SET/ DEMO
Confirms the setting./ Press DEMO in power off
state to demonstrate the function on display
window. To cancel it, press DEMO again.
TIMER
With the TIMER function you can turn USB, CD
play and TUNER reception on or off at a desired
time.
CLOCK
For setting the clock and checking the time.
h B (OPEN/CLOSE)
Ejects or insert the disc from slot loader.
i C/V (Skip/Search):
Goes to next or previous file/track/chapter.
Searches backward or forward (Press and hold)
Tunes in the desired radio station.
d/M (PLAY / PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
j -/+ (VOLUME)
Adjusts speaker volume.
Z (STOP)
Stops playback.
k USB REC.
Recoding to USB.
l PORT. IN
Connects to a portable player with audio
outputs.
PHONES
Headphone jack
1
Getting Started
d Display window
Shows the current status of the unit.
11
12
Getting Started
Rear panel
1
Getting Started
a OPTICAL IN
Connects to optical audio equipment.
b HDMI OUT
Connects to TV with HDMI inputs.
(Interface for digital audio and video)
c Antenna Connector
FM- Connects the FM wired antenna
d VIDEO OUT
Connects to a TV with video inputs.
e COMPONENT VIDEO (Y PB PR)OUTPUT
(PROGRESSIVE SCAN)
Connects to a TV with Y PB PR inputs.
f Speakers connectors
Connects the speaker cables.
g Cooling Fan
h Power cord
Connecting
13
Attaching the speakers
to the unit
Connections to Your
TV
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
Make one of the following connections, depending
on the capabilities of your existing equipment.
Connect the black stripe of each wire to the
terminals marked - (minus) and the other end to
the terminals marked + (plus).
, Note
 Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
> Caution
 Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel
> Caution
 The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
 Make sure to install the speaker with other
people in order to prevent it from falling
and causing injuries to the installer.
 Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
2
Connecting
 Depending on your TV and other
equipment you wish to connect, there are
various ways you could connect the player.
Use only one of the connections described
in this manual.
14
Connecting
Component Video Connection
HDMI Out Connection
Connect the COMPONENT VIDEO OUTPUT
(PROGRESSIVE SCAN) jacks on the unit to the
corresponding input jacks on the TV using
component cables.
If you have a HDMI TV or monitor, you can connect
it to this unit using a HDMI cable (Type A, High
Speed HDMI™ cable).
Connect the HDMI OUT jack on the unit to the
HDMI IN jack on a HDMI compatible TV or monitor.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
You can hear the sound through the system’s
speakers.
2
Connecting
Unit
Unit
TV
TV
Green
Blue
Red
, Tip
 You can fully enjoy digital audio and video
signals together with this HDMI connection.
 When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution” on page 16.)
Connecting
, Note
 If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or
may not output.
Video Connection
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
You can hear the sound through the system’s
speakers.
Unit
2
Connecting
 When you connect a HDMI or DVI
compatible device make sure of the
following:
- Try switching off the HDMI/DVI device and
this unit. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this unit.
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or 576p),
1 280 x 720p, 1 920 x 1 080i or 1 920 x 1 080p
video input.
 Not all HDCP-compatible HDMI or DVI
devices will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
 If there is noise or lines on the screen, please
check the HDMI cable and usea higher
version cable than High Speed HDMI™
cable.
> Caution
 Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the unit and then turn it
on again.
 When the HDMI connection with HDCP is
not verified, TV screen is changed to black
or green screen or the snow noise may
occur on the screen. In this case, check the
the HDMI connection, or disconnect the
HDMI cable.
15
TV
Yellow
16
Connecting
Resolution Setting
The unit provides several output resolutions for
HDMI OUT and COMPONENT VIDEO OUT jacks. You
can change the resolution using [Setup] menu.
1. Press n HOME.
2. Use A/D to select the [Setup] and press b
ENTER. The [Setup] menu appears.
Optional Equipment
Connection
AUDIO (PORT. IN) In
Connection
Connect an output of portable device (MP3 or PMP
etc) to the AUDIO (PORT. IN) input connector.
2
Connecting
3. Use W/S to select [Display] option then press
D to move to the second level.
4. Use W/S to select the [Resolution] option
then press D to move to the third level.
5. Use W/S to select the desired resolution then
press b ENTER to confirm your selection.
, Note
If your TV does not accept the resolution you
have set on the player, you can set resolution
to 480p (or 576p) as follows:
Press Z STOP for more than 5 seconds.
Video Output
Resolution
Displayed resolution in display window and
outputted resolution may different according to
connection type.
[HDMI OUT]: 1 080p, 1 080i, 720p and 480p (or
576p) and 480i (or 576i)
[COMPONENT VIDEO OUT]: 480p (or 576p) and 480i
(or 576i)
[VIDEO OUT]: 480i (or 576i)
MP3 player, etc...
Listening to music from your
portable player or external
device
The unit can be used to play the music from many
types of portable player or external devices.
1. Connect the portable player to the
PORT.IN(PORTABLE IN) connector of the unit.
2. Turn the power on by pressing 1 (POWER).
3. Select the PORTABLE function by pressing
P RADIO&INPUT.
4. Turn on the portable player or external device
and start it playing.
Connecting
17
USB Connection
OPTICAL In connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Connect an optical output of Unit (or Digital Device
etc) to the OPTICAL IN connector.
2
You can only recharge your iPod through USB
port. To listen to music on iPod, refer to the page
18.
Connecting
Removing the USB Device from the unit
1. Choose a different function mode or press
Z STOP twice in a row.
2. Remove the USB device from the unit.
To the digital
optical output jack of
your component
Compatible USB Devices
 MP3 Player : Flash type MP3 player.
 USB Flash Drive :
Devices that support USB2.0
or USB1.1.
 The USB function of this unit does not support
some USB devices.
USB device requirement
 Devices which require additional program
installation connected to a computer, are not
supported.
 Do not extract the USB device while in operation.
 For a large capacity USB, it may take longer than
a few minute to be searched.
 To prevent data loss, back up all data.
 If you use a USB extension cable or USB hub, the
USB device is not recognized.
 Using NTFS file system is not supported. (Only
FAT(16/32) file system is supported.)
 This unit is not supported when the total
number of files is 1 000 or more.
 External HDD, Card readers, Locked devices,
or hard type usb devices are not supported.
 USB port of the unit cannot be connected to PC.
The unit can not be used as a storage device.
Home theater speaker ez
setup
Listen to sound from TV, DVD and Digital Device
with 5.1(2.1 or 2)ch mode. Even in power off
mode, if you press OPTICAL, then power is on and
automatically changed to AUX OPT mode.
1. Connect the unit’s OPTICAL IN jack to jack on
optical out of your TV (or Digital Device etc.).
2. Select the AUX OPT by using the OPTICAL.
To select the AUX OPT directly.
3. Listen sound with 5.1(2.1 or 2)ch speaker.
4. To escape from AUX OPT by using the OPTICAL.
Function is retuned to previous one.
18
Connecting
Antenna Connection
Playing the iPod
Connect the supplied FM antenna for listening to
the radio.
You can enjoy the sound with your iPod. For details
about iPod, refer to the iPod User Guide.
Connect the FM Wire antenna to the FM antenna
connector.
1. Connect the iPod firmly.
2
Connecting
If you turn this unit on, your iPod is
automatically turned on and recharging starts.
2. Press FUNC. on the unit or P RADIO&INPUT
on the remote control to select iPod function.
You can operate your iPod through an iPod’s
display by using the supplied remote control
and also control on your iPod.
, Note
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it
as horizontal as possible.
Connecting
To
19
, Note
Do this
ON REMOTE
Pauses or
restart
d/M
d/M
Skip
C/V
C/V
Search
Press and hold
C/V
Press and hold
c/v
Move to the
previous
menu
-
A
Move to the
desired item
-
Chooses a
item
-
W/S
D
Compatible iPod
 We recommend installing the latest software
version.
 The unit supports the models as follows/ iPod
nano 1 G, 2 G, 3 G, 4 G, 5 G, 6 G/
iPod classic/ iPod 4 G, 5 G/
iPod touch 2 G, 3 G, 4 G/ iPhone 3 G, 4. For some
models, the unit may not operate depending on
the firmware version.
 Depending on your iPod’s software version, you
may not control your iPod from the player.
- Your iPod is not connected firmly.
- This unit recognizes your iPod as an
unknown device.
- Your iPod is exceptionally low in power.
/ The battery needs to be charged.
/ If you charge the battery while iPod
is extremely low in power, it may take
longer to be charged.
 iPod does not support recording function
when connected.
 Depending on your iPod’s software version,
it may not be possible to control your iPod
from this unit. We recommed installing the
latest software version.
 If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
iPod dock of this unit and then use it.
 If you have a problem with your iPod, please
visit www.apple.com/support/ipod.
2
Connecting
ON UNIT
 If this unit displays an error message, follow
the message. An error message “ERROR”.
20 System Setting
Adjust the setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
To display and exit the Setup
menu
1. Press n HOME.
Displays the [Home Menu].
You can also set a language for the subtitles and
the Setup menu, among other things. For details on
each Setup menu item, see pages 20 to 23.
2. Select an [Setup] by using A D.
OSD Initial language settings
- Optional
3
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using
the unit. English will be selected as the initial
language.
1. Press 1 (POWER) to turn the unit on. The
language setup menu will appear on the screen.
3. Press b ENTER.
Displays the [Setup].
4. Press n HOME or x RETURN to exit in the
[Setup] Menu.
About help menu for Setup
Menu
Buttons
Operation
WS
Moving to another
menu.
a
Move
A
Moving to previous
level.
d
Move
D
Moving to next
level or selecting
menu.
x RETURN
To exit the [Setup]
menu.
b ENTER
To confirm menu.
ws
Move
x
2. Use WSAD to select a language then press
b ENTER.
The confirm menu will appear.
3. Use AD to select the [Enter] then press b
ENTER to finish the language setup.
Close
b
Select
System Setting
21
Language
Display Mode
Menu Language
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
Select a language for the Setup menu and then on
screen display.
[Letterbox]
Disc Audio / Disc Subtitle / Disc
Menu
[Panscan]
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the
disc was recorded.
To select another language, press numeric
buttons and then b ENTER to enter the
corresponding 4-digit number according to
the language code list on the page 35. If you
enter the wrong language code, press CLEAR.
[Off (for Disc Subtitle)]
Turn off Subtitle.
Display
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with
Pan Scan, the picture is displayed at Letterbox
ratio.)
Resolution
Sets the output resolution of the Component and
HDMI video signal. Refer to “Resolution Setting” for
details about the resolution (page 16).
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV. If the COMPONENT
VIDEO OUT is only connected, this changes the
resolution to 480i (or 576i) as default resolution.
[1080p]
TV Aspect
Outputs 1 080 lines of progressive video.
Select which screen aspect to use based on the
shape of your TV screen.
[1080i]
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
Outputs 1 080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[480p (or 576p)]
Outputs 480 (or 576) lines of progressive video.
[480i (or 576i)]
Outputs 480 (or (576) lines of interlaced video.
3
System Setting
[Other]
Displays a wide picture with bands on the
upper and lower portions of the screen.
22 System Setting
Audio
Lock (Parental Control)
DRC (Dynamic Range Control)
Initial Setting the Area Code:
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
When you use this unit for the first time, you have
to set the Area Code.
1. Select the [Lock] menu and then press D.
Vocal
Select [On] to mix karaoke channels into normal
stereo.
This function is effective for multi-channel karaoke
DVDs only.
3
HD AV Sync
System Setting
Sometimes Digital TV encounters a delay between
picture and sound. If this happens you can
compensate by setting a delay on the sound so
that it effectively ‘waits’ for the picture to arrive:
this is called HD AV Sync. Use WS (on the remote
control) to scroll up and down through the delay
amount, which you can set at anything between 0
and 300m sec.
2. Press D.
To access the [Lock] options, you must input the
password you have created. Input a password
and press b ENTER. Enter it again and press b
ENTER to verify. If you make a mistake before
pressing b ENTER, press CLEAR.
3. Select the first character using W S buttons.
4. Press b ENTER and select the second character
using W S buttons.
5. Press b ENTER to confirm your Area code
selection.
Rating
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
1. Select [Rating] on the [Lock] menu then press
D.
2. Input a password and press b ENTER.
3. Select a rating from 1 to 8 using the WS
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not
active and the disc plays in full.
4. Press b ENTER to confirm your rating selection.
System Setting 23
Password
Others
You can enter or change password.
1. Select [Password] on the [Lock] menu and then
press D.
2. Press b ENTER.
3. Input a password and press b ENTER.
To change the password, press b ENTER when
the [Change] option is highlighted. Input a
password and press b ENTER. Enter it again
and press b ENTER to verify.
4. Press n HOME to exit the menu.
,
Note
If you forget your password, you can clear it
using the following steps:
2. Input the 6-digit number “210499” and
press b ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 34.
1. Select [Area Code] on the [Lock] menu then
press D.
2. Input a password and press b ENTER.
3. Select the first character using W S buttons.
4. Press b ENTER and select the second character
using W S buttons.
5. Press b ENTER to confirm your Area code
selection.
We provide you with the DivX® VOD (Video On
Demand) registration code that allows you to rent
and purchase videos using the DivX® VOD service.
For more information, visit www.divx.com/vod.
[Register]
Displays the registration code of your player.
[Deregister]
Deactivate your player and display the
deactivation code.
, Note
All the downloaded videos from DivX VOD can
only be played back on this unit.
3
System Setting
1. Select the [Setup] menu on the [Home
Menu].
DivX VOD
24 Operating
Using the Home Menu
1. Press n HOME.
Displays the [Home Menu].
2. Select an option by using AD.
3. Press b ENTER then selected option menu.
[Music] – Displays [MUSIC] menu.
[Movie] – Start video media’s playback or displays
the [MOVIE] menu.
[Photo] – Displays [PHOTO] menu.
[Setup] – Displays the [Setup] menu.
, Note
4
Operating
You can not select the [Music], [Movie] or
[Photo] option when the USB device is not
connected or a disc is not inserted.
Basic Operations
To
Stop
3. Select an option by using AD.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two devices, it
appears as belows. Select a media then press b
ENTER.
4. Press b ENTER then selected option menu.
, Note
 For the most Audio CD and DVD-ROM discs,
playback starts automatically.
 The unit plays only music file contained in
the USB storage device or disc automatically.
Press Z STOP.
Playback
Press d PLAY, MONO/
STEREO.
Pause
Press M PAUSE/STEP.
Press M PAUSE/STEP
Frame-byrepeatedly to play title FrameFrame playback
by-Frame. (DVD, DivX only)
During playback, press C/
V SKIP to go to the next
Skipping to the chapter/ track/ file or to
next/ previous return to the beginning of the
chapter/ track/ current chapter/ track/ file.
file
Press C SKIP twice briefly
to step back to the previous
chapter/ track/ file.
Locating a
point quickly by
playing a file in
fast forward or
fast reverse
1. Insert the disc by using the B OPEN/CLOSE or
Connect the USB device to the USB port.
2. Press n HOME.
Displays the [Home Menu].
Do this
Playing
repeatedly or
randomly
During playback, press c/
v SCAN repeatedly to
select the required scan speed.
To return to normal speed,
press d PLAY, MONO/
STEREO.
Press REPEAT repeatedly,
and the current title, chapter
or track will be played back
repeatedly or randomly.
- DVD : Chapter/ Title/ Off
- DivX : Title/ All/ Off
- Audio CD/ MP3/ WMA : Track/
All/ Random/ Off
Slowing down
the playing
speed
In the pause mode, press
SLOW (c or v) to select
the required speed. (DVD, DivX
only) The DivX file cannot be
slow down reverse playback.
Operating 25
Other Operations
To display the DVD title
r
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
1. Press m INFO/DISPLAY to show various
playback information.
The displayed items differ depending on the
disc type or playing status.
2. You can select an item by pressing WS and
change or select the setting by pressing AD.
Title – Current title number/ total number of titles.
Chapter – Current chapter number/ total number
of chapters.
When you play a DVD which contains several title,
you can select the title you want using the Menu.
1. Press TITLE.
The disc’s title appears.
2. Select the menu by pressing WSAD.
3. Press d PLAY, MONO/STEREO to confirm.
1.5 times speed playback
r
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
Time – Elapsed playing time.
1. During playback, press d PLAY, MONO/
STEREO to play at 1.5 times speed. “dX1.5”
appears on the screen.
Audio – Selected audio language or channel.
2. Press d PLAY, MONO/STEREO again to exit.
Angle – Selected angle/ total number of angles.
, Note
If any button is not pressed for a few seconds,
the on-screen display disappears.
To display the DVD Menu
r
When you play a DVD which contains several menu,
you can select the menu you want using the Menu.
Screen Saver
The screen saver appears when you leave the unit
in Stop mode for about five minutes.
Starting play from selected
time
ry
To start playing at any chosen time on the file or
title.
1. Press m INFO/DISPLAY during playback.
1. Press DISC MENU.
The disc’s menu appears.
2. Press WS to select the time clock icon and
“--:--:--” appears.
2. Select the menu by using WSAD.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by using
numerical buttons.
3. Press d PLAY, MONO/STEREO to confirm.
4. Press b ENTER to confirm. Playback starts from
the selected time.
4
Operating
Subtitle – Selected subtitle.
26 Operating
Resume playback
Marked Playback
ryut
ut
The unit records the point where you pressed the
Z STOP depending on the disc.
If “MZ (Resume Stop)” appears on the screen briefly,
press d PLAY, MONO/STEREO to resume playback
(from the scene point).
The mark function enables you to store your
favourite files from any disc or USB device in the
unit memory.
If you press Z STOP twice or unload the disc,
“Z”(Complete Stop) appears on the screen. The
unit will clear the stopped point.
, Note
The resume point may be cleared when a
button is pressed (for example; 1 (POWER),
B OPEN/CLOSE, etc).
1. Select [Music] on the [Home Menu].
Returning to the upper folder.
(MP3/ WMA only)
File information will be displayed
according to the ID3TAG information
on the appropriate music file. (MP3
only)
Changing subtitle code page
4
y
Operating
If the subtitle is not displayed properly, you can
change the subtitle code page to view the subtitle
file properly.
1. During playback, press m INFO/DISPLAY to
display the On-Screen display.
Selecting all tracks/ files.
Deselecting all tracks/files.
Moving to the previous or
next file list.
2. Use WS to select the [Code Page] option.
3. Use AD to select desired code option.
4. Press x RETURN to exit the On-Screen display.
2. Select a desired music on the [List] by using the
WS then press MARKER to appears the mark on
the list.
3. Press b ENTER or d PLAY, MONO/STEREO.
Displays the play mode.
4. Select the play mode by using the WS and press
b ENTER.
[Mark Play]
Marked playback.
[Current Play]
Normal playback.
, Note
If you want to select all files on the list, select
[Select All] and press b ENTER.
Operating 27
To delete a Marker
1. Use WS to select the track that you wish to erase
from the marked file.
2. Press MARKER.
To delete all Markers
Use WSAD to select [Deselect All] then press b
ENTER in program edit mode.
, Note
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
About help menu in the [Photo] menu
Menu
Buttons
Operation
d Slide
Show
d
PLAY, MONO/
STEREO
wsad
Move
SWAD
Moving to another
file or content.
b
Select
b ENTER
Viewing a particular
file.
x
Close
x RETURN
Viewing a slide
show.
Returning to the
[Home Menu].
About help menu in the full screen
Viewing a PHOTO file
i
Menu
Buttons
Operation
Menu
m
INFO/
DISPLAY
Displaying the Option
menu.
a/d
Prev./ Next
A/D
Moving to another file.
This unit can play discs with photo files.
x
Moving to the previous or
next file list.
Returning to the upper
folder.
2. Press W S to select a folder, and then press b
ENTER.
3. If you want to view a slide show, press W S
to highlight a file and press d PLAY, MONO/
STEREO.
Close
x
RETURN
Returning to the
[Photo] menu.
4
Operating
1. Select [Photo] on the [Home Menu] and press
b ENTER.
28 Operating
Options while viewing a photo
System Select - Optional
You can use various options during viewing a
photo in full screen.
You must select the appropriate system mode for
your TV system. Press and hold M PAUSE/STEP
for more than five seconds to be able to select a
system in the [Home Menu].
1. While viewing a photo in full screen, press
m INFO/DISPLAY to display the option menu.
, Note
2. Select an option using WSAD.
If the USB device is connected or a disc is
inserted, this function is not operated.
Adjust the speaker level
settings
a
You can adjust the sound level of each speaker.
b
c
d
e
a Current photo/ Total number of photos –
Use AD to view previous/next photo.
4
Operating
b Slide Show z/M– Press  ENTER to start
or pause slide show.
c Speed x3/ x2/ x1 – Use  ENTER to select
a delaying speed between photos in a slide
show.
d Rotate – Press  ENTER to rotate the photo.
e Go to list – Press  ENTER to return [Photo]
menu.
Last Scene Memory
r
This unit memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
1. Press SPEAKER LEVEL repeatedly to select a
desired speaker to set.
2. Press VOL -/+ to adjust the sound level of the
selected speaker while the level setting memu
is displayed on the display window.
3. Repeat and adjust the sound level of the other
speakers.
Operating 29
Setting the Clock
Sleep Timer Setting
1. Turn the unit on.
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will
turn off.
2. Press CLOCK for at least 2 seconds.
3. Choose time mode by pressing C/V.
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4. Press SET to confirm your selection.
5. Select the hours by pressing C/V.
6. Press SET.
7. Select the minutes by pressing C/V.
8. Press SET.
Using your player as an alarm
clock
1. Turn the unit on.
2. Press TIMER. Each functions flashes.
4. “ON TIME” will be displayed. This is your desired
time to unit turns on. Press C/V to
change the hours and minutes and press SET to
save.
5. The “OFF TIME” will be displayed. This is your
desired time to unit turns off.
6. Press C/V to change the hours and
minutes and press SET to save.
7. Press C/V to change the volume and
press SET to save. The clock icon “(“ shows
that the alarm is set.
8. Press TIMER button 2 times. You can check the
setting status.
, Note
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
, Note
You can check the remaining time before the
Unit turns off.
Press SLEEP The remaining time appears in the
display window.
Dimmer
Press SLEEP once. The display window will be
darken by half. To cancel it, press SLEEP repeatedly
until dim off. If touch the buttons in Sleep Timer
mode, the buttons will be lightening for 5 seconds
and darkening again.
Turn off the sound temporarily
Press
MUTE to mute your unit.
You can mute your unit, for example, to answer
the telephone, the “q” is displayed in the display
window.
DEMO
In the power off state, it demonstrates the function
on display window by pressing DEMO. To cancel
the DEMO, press it again.
, Note
 If you set the clock time, you can check the
time by pressing CLOCK even when the
player is turned off.
 While DEMO, this unit will keep DEMO
status even if you unplug the power cord
connection.
 If you set the clock time and alarm, you
can check the alarm icon “(“ by pressing
CLOCK even when the player is turned off.
 You can enjoy other functions during
the DEMO. Then the DEMO will pause to
temporary.
 If you set the clock time and alarm, you
can check the alarm icon “(“ and setting
informaiton by pressing TIMER even when
the unit is turned off.
- Without input key in 10 sec, the DEMO
will play back automatically.
4
Operating
3. Press SET when the function you want to be
woken by is showing.
To check the remaining time, press SLEEP.
30 Operating
Radio Operations
Be sure that both FM aerials are connected. (Refer
to the page 18.)
Listening to the radio
1. Press P RADIO&INPUT until FM appears in
the display window.
The last received station is tuned in.
2. Press and hold TUNING (-/+) for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
Or
Press TUNING (-/+) repeatedly.
3. Adjust the volume by pressing -/+ on the front
panel or by pressing VOL (+/-)on the remote
control repeatedly.
4
Operating
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
1. Press P RADIO&INPUT until FM appears in
the display window.
2. Select the desired frequency by using TUNING
(-/+).
3. Press b ENTER a preset number will flash in
the display window.
4. Press PRESET (-/+) to select the preset number
you want.
5. Press b ENTER.
The station is stored.
6. Repeat the steps 2 to 5 to store other stations.
Deleting all the saved stations
1. Press and hold CLEAR for two seconds.
“ERASE ALL” will flash up on the unit display.
2. Press CLEAR to erase all saved of the radio
stations.
Deleting a saved station
1. Press PRESET - / + to Select a preset number
you want to delete.
2. Press CLEAR, the preset number will blink in the
display window.
3. Press CLEAR again, to delete the selectd preset
number.
Improving poor FM reception
Press d PLAY, MONO/STEREO on the remote
control. This will change the tuner from stereo to
mono and usually improve the reception.
Operating
Sound adjustment
On Display
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT.
You can change the SOUND EFFECT using A D
arrow key while the sound effect information is
displayed on.
The displayed items for the equalizer maybe
different depending on sound sources and effects.
You can enjoy more virtual
surround sound.
BYPASS
You can enjoy the sound
without equalizer effect.
Description
NAT PLUS
The NAT PLUS is Natural Plus
sound effect. You can enjoy
the natural sound effect same
as a 5.1-channel.
NATURAL
You can enjoy comfortable
and natural sound.
Local
specialization
equalizer
Regionally optimized sound
effect. (FORRO/ FUNK/
SERTANEJO/ DANGDUT/
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/
SAMBA/ SALSA/ CUMBIA/
AFRO)
AUTO EQ
Realizes the sound equalizer
that is the most similar to the
genre of which is included in
the MP3 ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock pop, jazz or classic
concert.
MP3 -- OPT
This function is optimized for
compressible MP3, WMA file. It
improves the treble sound.
BASS BLAST
During playback, reinforce
the treble, bass and surround
sound effect.
LOUDNESS
Improves the bass and treble
sound.
, Note
 In some of surround modes, some speakers,
there’s no sound or low sound. It depends
on the mode of surround and the source of
audio, it is not defective.
 You may need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
4
Operating
On Display
Description
VIRTUAL
Setting the surround mode
31
32 Operating
Advanced Operations
Recording to USB
You can record music or sound souce to USB device
by connecting in to the port on the unit.
 During recording MP3/WMA, there is no
sound.
1. Connect the USB device to the unit.
 When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Audio CD only)
2. Select a mode in which you want to record.
Play back a sound source first.
3. Start the recording by pressing X REC.
4. To stop recording, press Z STOP.
[All tracks/ files recording]
Record to USB in stop or play mode.
[Program list recording]
After marking desired file(s) and you can record
it to USB (Refer to the page 26).
4
, Note
 You can check the recording percentage
rate for the USB record on the screen during
the recording. (Audio CD or MP3/ WMA CD
only)
It’ll be stored as follows.
Operating
Audio CD
MP3/ WMA
 Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
 If USB recording does not work, the
message like “NO USB”, “ERROR”, “USB FULL”
or “NO REC” is displayed on the display
window.
 Multi card reader device or external HDD
can not be used for USB recording.
 A file is recorded by 128 Mbyte (about 2
hours) when you record for a long term.
There are recorded less than 4 files.
 When you stop recording during playback,
the file will not be stored.
 In the state CD-G, DTS disc USB record is not
operated.
 The files in the sub-folders are not recorded
during all track recording.
 You may not record more than 999 files.
The other
sources (Tuner,
Portable)
 The nunbering of the recording file is
entered from the lowest number. So if you
delete some of the recording files, the next
recording file could be the lowest number
among them.
The making of unauthorized copies of copyprotected material, including computer programs,
files, broadcasts and sound recordings, may be
an infringement of copyrights and constitute a
criminal offense. This equipment should not be
used for such purposes.
Be responsible
Respect copyrights.
Troubleshooting 33
Troubleshooting
PROBLEM
No power
No picture
CORRECTION
Plug the power cord into the wall outlet securely.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
Connect the video cables securely to both the TV and unit.
Select the correct input mode of the unit so you can hear the sound
from the unit.
There is little or no sound
Connect the audio cables into the connection terminals correctly.
Replace with a new audio cable.
The DVD picture quality is poor
Clean the disc using a soft cloth with outward strokes.
Insert a disc.
A DVD/CD will not play
Insert a playable disc (check the disc type, colour system and
regional code).
Enter your password or change the rating level.
Radio stations can’t be tuned in
properly
Clean the disc using a soft cloth with outward strokes.
Move unit and audio components further away from your TV.
5
Check the antenna connection and adjust its position.
Troubleshooting
Humming noise heard while a DVD
or CD is playing
Attach an external aerial if necessary.
Tune to the station manually.
Preset some radio stations, see page 30 for details.
The remote is not pointed directly at the unit.
Point the remote directly at the unit.
The remote is too far from the unit.
Use the remote within 23 feet (7m) of the unit.
The remote control doesn’t work
well / at all
There is an obstacle in the path between the remote control and
the unit.
Remove the obstacle.
The battery in the remote control are flat.
Replace the battery with new ones.
iPod does not work.
Check whether the player is connected to the unit correctly.
Connect it to the unit correctly.
34 Appendix
Area Code List
Choose an area code from this list.
Area
Code Area
Code Area
Code Area
Code
Afghanistan
AF Fiji
FJ Monaco
MC Singapore
SG
Argentina
AR Finland
FI Mongolia
MN Slovak Republic
SK
Australia
AU France
FR Morocco
MA Slovenia
SI
Austria
AT Germany
DE Nepal
NP South Africa
ZA
Belgium
BE Great Britain
GB Netherlands
NL South Korea
KR
Bhutan
BT Greece
GR Antilles
AN Spain
ES
Bolivia
BO Greenland
GL New Zealand
NZ Sri Lanka
LK
Brazil
BR Hong Kong
HK Nigeria
NG Sweden
SE
Cambodia
KH Hungary
HU Norway
NO Switzerland
CH
Canada
CA India
IN Oman
OM Taiwan
TW
Chile
CL Indonesia
ID Pakistan
PK Thailand
TH
China
CN Israel
IL Panama
PA Turkey
TR
Colombia
CO Italy
IT Paraguay
PY Uganda
UG
Congo
CG Jamaica
JM Philippines
PH Ukraine
UA
Costa Rica
CR Japan
JP Poland
PL United States
US
Croatia
HR Kenya
KE Portugal
PT Uruguay
UY
Czech Republic
CZ Kuwait
KW Romania
RO Uzbekistan
UZ
Denmark
DK Libya
Ecuador
EC Luxembourg
LY Russian
LU Federation
Egypt
EG Malaysia
6
El Salvador
SV Maldives
MY Saudi Arabia
MV Senegal
Appendix
Ethiopia
ET Mexico
MX
Vietnam
RU Zimbabwe
SA
SN
VN
ZW
Appendix 35
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
Language
Code
Language
Code
Language
Language
Afar
6565
Afrikaans
6570
French
7082
Frisian
7089
Albanian
8381
Ameharic
6577
Galician
Georgian
Arabic
Armenian
6582
German
6869
7289
Greek
6976
Assamese
6583
Greenlandic
7576
Aymara
6588
Guarani
7178
Azerbaijani
6590
Gujarati
7185
Bashkir
6665
Hausa
7265
Basque
6985
Hebrew
Bengali; Bangla
6678
Hindi
Bhutani
6890
Bihari
Breton
Lithuanian
7684
Sindhi
8368
Macedonian
7775
Singhalese
8373
7176
Malagasy
7771
Slovak
8375
7565
Malay
7783
Slovenian
8376
Malayalam
7776
Spanish
6983
Maori
7773
Sudanese
8385
Marathi
7782
Swahili
8387
Moldavian
7779
Swedish
8386
Mongolian
7778
Tagalog
8476
Nauru
7865
Language
Code
7387
Nepali
7869
Tajik
8471
7273
Norwegian
7879
Tamil
8465
Hungarian
7285
Oriya
7982
Telugu
8469
6672
Icelandic
7383
Panjabi
8065
Thai
8472
6682
Indonesian
7378
Pashto, Pushto
8083
Tonga
8479
Bulgarian
6671
Interlingua
7365
Persian
7065
Turkish
8482
Burmese
7789
Irish
7165
Polish
8076
Turkmen
8475
Byelorussian
6669
Italian
7384
Portuguese
8084
Twi
8487
Chinese
9072
Japanese
7465
Quechua
8185
Ukrainian
8575
Croatian
7282
Kannada
7578
Rhaeto-Romance 8277
Urdu
8582
Czech
6783
Kashmiri
7583
Rumanian
8279
Uzbek
8590
Danish
6865
Kazakh
7575
Russian
8285
Vietnamese
8673
Dutch
7876
Kirghiz
7589
Samoan
8377
Volapük
8679
English
6978 Korean
7579
Sanskrit
8365
Welsh
6789
Esperanto
6979 Kurdish
7585
Scots Gaelic
7168
Wolof
8779
7679
Serbian
8382
Xhosa
8872
Laothian
Estonian
6984
Faroese
7079 Latin
Fiji
7074
Finnish
7073
Code
7665
Serbo-Croatian
8372
Yiddish
7473
Latvian, Lettish
7686
Shona
8378
Yoruba
8979
Lingala
7678
Zulu
9085
6
Appendix
Code
36 Appendix
Trademarks and
Licenses
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is a trademark of Apple Inc. “Made
for iPod” and “Made for iPhone” mean that
an electronic accessory has been designed
to connect specifically to iPod or iPhone
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory with
iPod, iPhone may affect wireless performance.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
6
Appendix
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
DivX®, DivX Certified® and associated logos are
trademarks of DivX, Inc. and are used under
license.
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, Inc. This is an official
DivX Certified® device that plays DivX video.
Visit www.divx.com for more information and
software tools to convert your files into DivX
video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to
play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate
the DivX VOD section in your device setup menu.
Go to vod.divx.com for more information on how
to complete your registration.
What is SIMPLINK?
Some functions of this unit are controlled by
TV’s remote control when this unit and LG TV
with SIMPLINK are connected through HDMI
connection. Controllable functions by LG TV’s
remote control; Play, Pause, Scan, Skip, Stop,
Power Off, etc.
 Refer to the TV owner’s manual for the details
of SIMPLINK function.
 LG TV with SIMPLINK function has the logo as
shown above.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
 Use a higher version cable than High Speed
HDMI™ cable.
Appendix 37
Specifications
General
Power requirements
refer to main label
Power consumption
refer to main label
Dimensions (W x H x D)
135 X 295 X 315 mm without foot
Net Weight (Approx.)
3.45 kg
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Inputs/ Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
HDMI OUT (video/audio):
19 pin Type A, HDMI™ Connector
DIGITAL IN (OPTICAL):
3 V (p-p), Optical jack x 1
PORT. IN
0.5Vrms (3.5 mm stereo jack)
System
Laser
Semiconductor laser, wavelength: 650 nm
Signal system
Standard NTSC/ PAL color TV system
Frequency response
20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
More than 80 dB
Harmonic distortion
0.05 % at 1 W
Dynamic range
More than 85 dB
Bus Power Supply
USB DC 5 V 0 500 mA
iPod DC 5 V 0 1 A
Amplifier
Stereo mode
80 W + 80 W (4Ω at 1kHz)
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
6
Appendix
Signal-to-noise ratio
38 Appendix
Front Speaker
Type
3 Way 4 speaker
Impedance Rated
4Ω
Input Power
80 W
Max. Input Power
160 W
Net Dimensions (W x H x D)
126 X 295 X 315 mm
Net Weight
4.35 kg
Design and specifications are subject to change without notice.
6
Appendix
Appendix 39
Maintenance
Notes on Discs
Handling Discs
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
 Do not use volatile liquids such as insecticide
spray near the unit.
 Wiping with strong pressure may damage the
surface.
 Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Maintaining the Unit
6
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
Download PDF

advertising