LG | FLATRON-LCD-563LE-LB563T-GT | LG 563LE Owner’s Manual

The 563LE Flat Panel Monitor has
Transistor)
active matrix TFT
(Thin-Film
(Liquid Crystal Display).
designed for use in small working areas or for those who need
This monitor is
more
an
LCD
working space on the desk.
Features
The 563LE is
a
15.0-inch
(15.0
inches
viewable) intelligent micropro-cessor
based monitor.
Digitally controlled auto-scanning is done with the microprocessor for horizontal
frequencies between 31 and 61kHz, and vertical scan frequencies
scan
between 56 and 75Hz.
The
microprocessor-based digital controls allow you to adjust conveniently a
variety of image controls by using the OSD (On Screen Display).
The monitor is
shipped
with 14
factory pre-programmed
resident. In addition, there
of 30 memory modes.
permanently
Plug
and
play capability
if
are
video modes that
16 user-storable modes, for
a
are
total
supported by your system.
This monitor has DDC 2B function.*
Compliant with
-
-
the
following regulated specifications
:*
EPA ENERGY STAR
Swedish TCO'99
*For detailed information, please
refer to the Reference Guide
provided
.
Connecting
the Monitor
On the back of the monitor
power
1
2
cord,
Power off both the monitor and PC.
Connect the 15
pin VGA connector of
supplied signal cable to the output
matching input connector on the rear
of the monitor. The connectors will mate only one way. If you cannot attach
the cable easily, turn the connector upside down and try again. When mated,
tighten the thumbscrews to secure the connection.
VGA video connector
2'
plug-in connections; one for the AC
signal cable from the video card.
two
are
and the other for the
the
the PC and the
on
appropriate MAC to VGA adapter block at your local computer
adapter changes the high density 3 row 15 pin VGA connector to
the correct 15 pin 2 row connection to mate with your MAC. Attach the other
end of the signal cable to the side of the adapter block with 3 rows.
Locate the
store. This
Connect the attached
adapter block/signal
cable to the video output
on
your
MAC.
3
Connect the
unit. 1
Plug
4
5
plug
Connect
from the AC-DC
adapter
into the connector
on
the
display
end of the AC power cord into the AC-DC adapter.
the other end into a properly grounded three-prong AC outlet.
Power
If you
on
see
one
32
the PC, then the monitor.
the NO SIGNAL message, check the
signal
cable and
connectors.
6
After
using
the system, power off the monitor, then the PC.
IBM PC
MACINTOSH
Mac
D-15P
2
Adapter
2'
D-15P
1
Signal
3
Cable
Power Cord
*NOTE:Ifyou
2
AC-DC
seethe"OUTOF
RANGE" message, check to make
sure your system is set to one of the
adapter
factory preset modes.(see
A2
page
A8)
Location and Function of Controls
Front View
Power Indicator
Power Button
OSD
???
AUTO/SET
?
??
OSD Button
AUTO/SET Button
Buttons
VESA wall
Rear View
mounting
Connected to another
object
(stand type and wall-mounted
type optional)
-
ID Label
?
??
Kensington Security Slot
a locking
Connected to
D-Sub
Connecter
Signal
DC Power Connecter
+
-
NOTE
:
This monitor
accept
a
75mm
x
75mm
A3
cable that
can
be
purchased separately
most
computer
VESA-compliant mounting
at
stores
interface
pad.
Control Panel Function
Front Panel Controls
Buttons
Power Button
OSD Button
OSD
AUTO/SET
AUTO/SET Button
Power
Control
OSD
(DPMS)
Indicator
Function
Use this button to enter and from the
OSD Button
Buttons
Use these buttons to choose
the
on
display (OSD).
screen
on screen
or
adjust
items in
display.
<Shortcut
?
100
100
AUTO/SET
AUTO/SET Button
Keys>
Brightness and Contrast can be adjusted directly without
entering the On Screen Display (OSD) system. Touch
the
buttons to adjust the settings and then
the OSD button to save all changes. The Brightness
and Contrast functions
are
Screen
menu.
Display (OSD)
Use this button to enter
*
AUTO CONFIGURATION
AUTO
selection in the
on
adjustment function
Touch the AUTO/SET button before
This button is for the automatic
position,
clock and
Note: Some
properly.
If the results
This indicator
monitor
using OSD menu.
adjustment of the screen
phase.
signal from
graphics boards may not function
unsatisfactory, adjust your monitor's
manually.
some
are
Position, Clock and Phase
Power (DPMS)
Indicator
a
display.
screen
PROCESSING
also available in the On
lights
up green when the
operates normally. If the monitor is in
DPM (Energy Saving) mode (stand-by/
suspend/power off), this indicator color
changes to amber.
Power Button
Use this button to turn the monitor
A4
on or
off.
On Screen
Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system. A
quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
To make
adjustments
in the On Screen
Display,
OSD
AUTO/SET
3
45
Press the OSD Button, then the main
To
access a
becomes
control,
use
the
highlighted, press
Use the
Accept
follow these steps:
AUTO/SET
OSD
12
making image adjustment.
the
Buttons to
by Pressing
of the OSD appears.
Buttons. When the icon you want
the
AUTO/SET Button.
adjust
changes by pressing
Exit the OSD
menu
the item to the desired level.
the AUTO/SET Button.
the OSD Button.
A5
On Screen
You
Display(OSD) Selection
introduced to the
were
and
Adjustment
procedure of selection and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the items that are shown on the Menu.
OSD
Adjust
Description
Brightness
BRIGHTNESS CONTRAST
Used to
88
adjust
the
brightness
of the
screen.
100
Contrast
the
desired.
Adjust
PRESET
COLOR
PRESET
9300K
display
9300K/ 6500K
To appear the
6500K
to the contrast
displays
color
temperature.
RED
?
GREEN
?
BLUE
9300K:Slightly
6500K:Slightly
bluish white.
reddish white.
RED
To set your
own
color levels.
GREEN
To set your
own
color levels.
BLUE
To set your
own
color levels.
POSITION
Vertical Position
61
To
move
image
up and down.
39
Horizontal Position
To
A6
move
picture image
left and
right.
On Screen
Display(OSD) Selection
OSD
and
Adjust
Adjustment
Description
CLOCK
TRACKING
To minimize any vertical bars
stripes visible on the screen
background.The horizontal
change.
CLOCK
or
screen
size will also
PHASE
To
PHASE
adjust
the focus of the
display.
This item allows you to remove any
horizontal noise and clear or sharpen
the
image
LANGUAGE To choose the
SETUP
control
LANGUAGE
of characters.
language in which
displayed.
the
names are
ENGLISH
OSD POSITION
ELAPSED TIME
0H
OSD POSITION To
on
1024x768/60Hz
adjust position
the
of the OSD window
screen.
PRESET MODE
ELAPSED TIME To
A7
display
the
use
time of monitor
Video
Memory
Modes
The monitor has 30 memory locations for
factory preset to popular video modes.
display modes,
14 of which
are
Display Modes (Resolution)
Display Modes (Resolution)
123456789
Horizontal
Freq.(kHz)
Vertical
Freq.(Hz)
VGA
640
x
350
31.47
VGA
720
x
400
31.47
70
VGA
640
x
480
31.47
60
70
MAC
640
x
480
35.00
67
VESA
640
x
480
37.86
73
VESA
640
x
480
37.50
75
VESA
800
x
600
35.16
56
VESA
800
x
600
37.88
60
VESA
800
x
600
48.08
72
10
VESA
800
x
600
46.88
75
11
MAC
832
x
624
49.72
75
12
VESA
1024
x
768
48.36
60
13
VESA
1024
x
768
56.48
70
14
VESA
1024
x
768
60.02
75
User Modes
Modes 15-30 are empty and can accept new video data. If the monitor detects a
new video mode that has not been present before or is not one of the preset
modes, it stores the new mode automatically in one of the empty modes starting
with mode 15.
If you use up the 16 blank modes and still have more new video modes, the
monitor replaces the information in the user modes starting with mode 15.
A8
Check the
following before calling for service.
Display Position is incorrect.
Push the AUTO/SET Button.
If the results are unsatisfactory,
and V
On the
position
icon in the
screen
adjust the image position using
display.
background, vertical bars
or
stripes
Push the AUTO/SET Button.
If the results are unsatisfactory, decrease the vertical bars
CLOCK icon in the
on screen
or
in any
image
or
are
visible.
stripes using
characters
Push the AUTO/SET Button.
If the results are unsatisfactory, decrease the horizontal bars
on screen
position
the
display.
Any horizontal noise appearing
not clearly portraid.
icon in the
the H
on screen
using
are
the PHASE
display.
NO SIGNAL message.
The signal cable is not connected,
or
is loose. Check and
secure
the
connection.
OUT OF RANGE message appears.
Picture is blank.
The
frequency of
the
signal
from the video card is outside the
operating range
of the monitor.
Horizontal
Vertical
*
Use the
Frequency: 31kHz-61kHz
Frequency: 56Hz-75Hz
graphics board's utility software to change the frequency setting (Refer to the
graphics board).
manual for
*
You
F8
change the setup to the supported
key during booting the system).
can
resolution
using
the Safe Mode
(Press the
The power LED is illuminated amber.
The monitor is in its display power management mode.
There is
The
no
signal
active
signal coming
cable is not fastened
Check the computer power and
from the PC.
securely.
graphics adapter configuration.
saving off mode (Amber).
Computer video signal is not VESA DPMS standard. Either the PC or the video
controller card is not using the VESA DPMS power management function.
The monitor doesn't enter the power
Specifications
Display
15.0inch
Viewable Size
(38.1cm) Flat Panel Active matrix-TFT LCD,
coating
15.0inch (38.1cm)
Pixel
0.3
Type
Anti-Glare
Sync Input
pitch
Horizontal
31
Vertical
56
Freq.
Freq.
Input Form
Signal Input
Video
Input
Resolution
0.3mm
x
61kHz
(Automatic)
(Automatic)
Separate TTL, Positive/Negative
15 pin D-Sub Connector
-
-
75Hz
Display Area
Input Form
304
Max
VESA 1024
VESA 1024
Recommend
x
228mm / 12.0
Separate,
RGB Analog,
x
9.0inch
0.714Vp-p/75ohm,
x
768@75Hz
x
768@60Hz
Power
Normal
≤ 33W
Consumption
Stand-by/Suspend
≤
Power Off
≤3W
Width
38.92
cm
/ 15.95 inches
Height
Depth
36.25
cm
/ 14.24 inches
18.24
cm
/ 7.18 inches
Dimensions
Power
Input
3W
DC 12V 3A
Input
Output
AC 100-240V 50-60Hz 1.2A~0.6A
Weight
Net
4.8
Tilt
Down
5˚
Up
30˚
AC-DC Adapter
Range
Environmental
Conditions
DC 12V 3A
-
+
kg (10.58 lbs)
Operating Condition
10 ˚C to 35 ˚C
Temperature
10 % to 80 % non-Condensing
Humidity
Storage Condition
-20 ˚C to 60 ˚C
Temperature
5 % to 95 % non-Condensing
Humidity
NOTE
Information in this document is
subject
to
change without
A10
notice.
Positive
Download PDF

advertising