LG | 710E | LG 710E Owner’s Manual

User's Guide
710E
710S
710B
Make
sure
to read the
Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached
on
the back cover and quote this information to your
dealer when you require service.
Precautions
Important
This unit has been
engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this monitor, observe the following basic rules for its
installation, use, and servicing. Keep it in an accessible place for future
reference.
On
Safety
power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
Use
only the
manufacturer
or
the nearest authorized
repair service provider for a replacement.
The power supply cord is used as the main disconnect device. Ensure that the
socket-outlet is easily accessible after installation.
Operate
the monitor
this manual
or
listed
only from
on
power source indicated in the specifications of
the monitor. If you are not sure what type of power supply
a
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
cords and broken
plugs. They
technician for replacement.
Hands must be
Do not
It
dry when holding the
damage the
can cause
Make
may result in
fire
sure to
or
power cord by
electric shock.
completely insert the
are
a
power
dangerous. So are frayed
shock
plug
or
power
fire hazard. Call your service
to avoid an electric shock.
disassembling, bending, pulling
power
or
plug. Insecure connections
heating
can cause
fire.
Do not
Open
There
the Monitor.
serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the monitor is not operating properly.
are no user
To Avoid Personal
Injury
:
place the monitor on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not try to roll a stand with small casters across thresholds or deep pile
Do not
carpets.
A1
up.
To Prevent Fire
or
Hazards:
Always turn the monitor OFF if you leave the room for more than a short period
of time. Never leave the monitor ON when leaving the house.
Keep children from dropping or pushing objects into the monitor's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this monitor.
During a lightning storm or when the monitor is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Do not bring magnetic devices such as magnets or motors near the picture
tube.
On Installation
Do not allow
anything
to rest upon or roll over the power
the monitor where the power cord is
Do not
use
this monitor
sink, laundry tub, in
near water
not
place
subject to damage.
such
basement,
cord, and do
as near a
bathtub, washbowl, kitchen
swimming pool.
Monitors are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
a wet
or near a
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the monitor on a bed, sofa, rug,
can cause
etc.
Place the monitor in
built-in enclosure unless proper ventilation is
with cloth or other material.
a
Cover the openings
Place the monitor near
or over a
Do not install the monitor in
On
a
radiator
or
dusty area. It
heat
provided.
source.
can cause
fire.
Cleaning
Unplug the monitor before cleaning the face of the monitor screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the
monitor
On
screen
because overspray may
cause
electrical shock.
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
Connecting
the Monitor
Before
setting up the monitor, ensure that the power is turned off to the
monitor, computer system, and other attached devices.
Carefully set the monitor face-down with the underside facing you.
Connecting
the Tilt/Swivel stand
1. Align the hooks on the tilt/swivel stand with the matching slots in the base of
the monitor.
2.
3.
Insert the hooks into slots.
Slide the tilt/swivel stand toward the front of the monitor until the latches click
into the locked position.
NOTE
This illustration depicts the general model of connection. Your monitor may differ from the
items shown in the picture.
Slot
Hook
Latch
A3
Hook
Connecting
the Monitor
Using the Computer
1. Connect the signal cable. When mated, tighten the thumbscrews to secure the
connection.
2. Connect the power cord into a properly power outlet that is easily accessible and
close to the monitor.
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your monitor
may differ from the view as shown.
Signal Cable
Power Cord
Attached Type*
Wall-outlet
type*
Detached Type*
*
Varies according to model.
PC-outlet
type*
PC
MAC
Mac adapter
For Apple Macintosh use,
separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
A4
a
Control Panel Functions
Front Panel Controls
Control
Power Button
Power
(DPMS)
Indicator
MENU Button
Function
Use this button to turn the monitor
on or
off.
This Indicator
lights up green when the monitor
operates normally. If the monitor is in DPM
(Energy Saving) mode, this indicator will flicker.
Use this button to enter
exit the
or
on screen
display.
Buttons
Use these buttons to choose
the
SELECT Button
on screen
adjust
items in
display.
Use this button to enter
screen
or
a
selection in the
on
display.
CONTROLS LOCKED/UNLOCKED
:
CONTROLS LOCKED
CONTROLS UNLOCKED
MENU and
This function allows you to secure the current
control settings, so that they cannot be
inadvertently changed. Press and hold the MENU
button and
button for 3 seconds: the message
"CONTROLS LOCKED" appears.
unlock the OSD controls at any time by
button for 3
pushing the MENU button and
seconds:
The message "CONTROLS UNLOCKED" will
You
can
appear.
A5
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor is quick and easy with the On Screen Display Control system. A
short example is quick and easy given below to familiarize you with the use of
the controls. The following section is an outline of the available adjustments
and selections you can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before
To make
adjustments
in the On Screen
Display, follow these steps:
Press the MENU Button, then the main
To
access a
becomes
control,
highlighted,
Use the
menu
of the OSD appears.
Buttons. When the icon you want
press the SELECT Button.
use
the
making image adjustments.
Buttons to
or
adjust the item
to the desired level.
Accept the changes by pressing the SELECT Button.
Exit the OSD
by Pressing the MENU Button.
A6
On Screen
Display(OSD)
Selection and
Adjustment
following table indicates all the On Screen Display control, adjustment,
and setting menus.
The
Icon
Main
Icon
menu
Main
menu
Corner*
Contrast
Bottom
Brightness
H
H Position
H Moire
H Size
V Moire
V Position
COLOR
Corner*
V Size
9300
6500
K
Tilt*
RGB
Pincushion
Pin Balance
Recall
Parallelogram
Reset
Trapezoid
Language
Top Corner*
OSD Time
Video Level
:
Adjustable
Degauss
Information
Exit*
NOTE
The order of icons may differ
*
This function is available
depending on the model (A7~A10).
for designated models only.
A7
On Screen
Display(OSD)
Selection and
Adjustment
procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
You
introduced to the
were
Icon
Sub
Description
menu
To
adjust
the contrast of the
To
adjust
the
To
move
image
To
adjust image
To
move
To
adjust image height.
screen.
CONTRAST
brightness
of the
screen.
BRIGHTNESS
left and
right.
H POSITION
width.
H SIZE
image
up and down.
V POSITION
V SIZE
To correct
image
rotation.
To correct
a concave or convex
TILT*
PINCUSHION
image.
bowing
To correct the balance of both sides
of the
bowing.
PIN BALANCE
To
PARALLELOGRAM
correctly adjust
To correct
the skew of the
geometric
TRAPEZOID
A8
distortion.
image.
On Screen
Display(OSD)
Sub
Icon
Selection and
Description
menu
To correct
TOP
an
irregular
distortion of the
displayed
an
irregular
distortion of the
displayed
an
irregular
distortion of the
displayed
image.
CORNER*
To correct
BOTTOM
Adjustment
image.
CORNER*
To correct
*
image.
H CORNER
This item allows you to reduce the degree of moire.
(Moire is caused by interference Horizontal Scan
Line with the periodical dot screen). It is normally
H MOIRE
OFF(H:0/V:0).
The moire adjustments
V MOIRE
may affect the focus of the
screen.
Moire adjustments may shake
moire reduction function is on.
COLOR
9300
Slightly
bluish white.
6500
Slightly
reddish white.
K
RGB
?OK
?
RECALL
CANCEL
slightly
while the
Select the screen temperature which you prefer
among reddish or bluish or any color in between.
Set your
own
color levels.
You can use this function to reload the modified parameters
for screen display operation, as specified by the user after
purchase: Position, Size, Side Pincushion, Side Pincushion
Balance, Parallelogram, Trapezoid, Top Corner, Bottom
Corner (These recalled options may differ depending on the
mode selected: Preset, User, or New).
If you don't want to recall the monitor to these
modified settings, use the
button to select
CANCEL and then press the SELECT button.
A9
On Screen
Display(OSD)
Sub
Icon
CANCEL
RESET
Adjustment
Description
menu
?OK
?
Selection and
Return to all
factory default settings except "LANGUAGE":
Brightness, Contrast, Tilt, Color 9300, Video Level, OSD
Time, Moire (These reset options may differ depending on
the mode selected: Preset, User, or New).
If you don't want to reset the monitor, use the
button to select CANCEL and then press
the SELECT button.
To choose the
are
in which the control
names
displayed.
OSD Menus
LANGUAGE
language
are
available in 12
languages: English,
German, French, Spanish, Italian, Swedish, Finnish,
Portuguese, Korean, Chinese Russian and Polish.
,
?5
?10
OSD TIME
?20
?30
Set the OSD time, i.e. the length of time a menu
will remain on-screen before it shuts off
automatically. Adjust the time to 5, 10, 20, 30 or 60
seconds.
?60
?
?
0.7V
1.0V
VIDEO LEVEL
This item is used to select the monitor's input signal
level. The normal level used for most PCs is 0.7V.
If the screen becomes suddenly washed-out or
blurred, please select 1.0V and try again.
To
manually demagnetize the screen
showing incorrect images or colors.
U
DEGAUSS
?
?
PRESETMODE
To inform
users
of preset and
user
USER MODE
INFORMATION
To exit from current OSD
*
EXIT
A10
menu.
to avoid
mode data.
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
monitor connected?
Is the power indicator light
on?
Is the power on and the
power indicator green?
Is the power indicator
?
?
Press the Power button.
?
Adjust the brightness and the contrast.
?
If the monitor is in power saving mode, try moving the
mouse or pressing any key on the keyboard to bring up
the screen.
flickering?
Doyouseean"OUTOF
?
FREQUENCY" message
on the screen?
Doyouseea"SELF
?
DIAGNOSITICS" message
on the screen?
The
screen
is
Check and see if the power cord is connected properly
to the power outlet.
This message appears when the signal from the PC
(video card) is out of horizontal or vertical frequency
range of the monitor. See the 'Specifications' section of
this manual and configure your monitor again.
This message appears when the signal cable between
your PC and your monitor is not connected. Check the
signal cable and try again.
flickering.
Is the vertical frequency
less than 70Hz or is your
monitor set to the
interlaced mode?
Do you have any
magnetic material such
?
?
adapter, or highvoltage line near to your
Set the vertical frequency to 72Hz or higher, and
consult the video card user manual for instructions
on converting to a non-interlaced mode.
(You can set this option under the Display icon of the
Control Panel.)
Remove
magnetic sources, such as power
adapters, speakers, or high-voltage lines, away from
the monitor.
as
monitor?
Do you hear a "~ding"
sound while the monitor
is flickering?
?
Use the normal degaussing function. This function
clears the screen and reduces any screen blur that
may occur due to the surrounding magnetic field.
The screen may flicker for about 5 seconds,
accompanied by a "~ding"sound.
A11
Troubleshooting
The
screen
color is not normal.
Do you see basic
discoloration (16 colors)?
?
Is the screen color
unstable or monochrome?
Do you see black dots on
the screen?
?
?
Set the color depth to 256 colors or higher: use 'Control
Panel' -> 'Display' -> 'Settings' ->'Color Palette'
Check the connection of the signal cable. Or pull out the
video card of the PC and insert it again.
This is due to a small amount of foreign or abnormally
florescent material that became fastened on the mask
during manufacturing. It will not affect product
performance.
Do you see a partial
blurring on the screen?
I
see an
after-image
Do you see the afterimage even when you
turn off the monitor?
I
?
see waves on
the
Do you see the wave
directly on the screen?
on
?
This happens due to interference from surrounding
magnetic fields, as created when speakers, steel
structures, or high-voltage lines are placed near the
monitor. Remove any such materials from the
immediate vicinity and use the DEGAUSS icon on the
screen adjustment menu to fix the screen.
the
screen.
A premature aging of the monitor pixels may cause the
prolonged display of a single image on the screen. Be
sure to use a screen saver to maximize the service life of
the monitor.
screen.
?
This occurs in inverse proportion to the screen focus,
which can be caused by a particular frequency or video
card. Brighten the screen and use the 'MOIRE' icon on
the screen adjustment menu to adjust the screen.
Have you installed the monitor driver?
Have you installed the
monitor driver?
?
Be sure to install the monitor driver from the monitor
driver CD (or diskette) that comes with your monitor. Or,
you can also download the driver from our web site:
http://www.lge.com.
A12
Specifications
Picture Tube
17 inches (16.0 inches viewable)
degree deflection
0.23mm/0.27mm (Ph/Pp)
90
AGARAS(Anti-Glare Anti-Reflective Anti-Static) coating(710B/710S)
Sync Input
Horizontal
Vertical
Video
Input
Resolution
30
Freq.
-
50
Freq.
-
71kHz (Automatic)
160Hz (Automatic)
Input Form
Signal Input
Separate TTL, Positive/Negative
15 pin D-Sub Connector
Input Form
Separate, RGB Analog, 0.7Vp-p/75 ohm,
Max
VESA 1280
x
1024 @60Hz
Recommend
VESA 1024
x
768 @85Hz
Plug&Play
DDC 2B
Power
Normal
Consumption
Stand-by/Suspend
≤
DPM Off
≤5W
73W
15W
Dimensions
Width
&Weight
(with tilt/ swivel
stand)
Power
AC 100-240V~ 50/60Hz 2.0A
Input
Environmental
Conditions
40.0
cm
Height
Depth
/ 15.74 inches
39.75 cm / 15.65 inches
41.1 cm / 16.18 inches
Net
14.0
kg (30.86 lbs)
Operating Conditions
0˚C to 40 ˚C
Temperature
10 % to 80 % non-Condensing
Humidity
Storage Conditions
-20˚C to 60 ˚C
Temperature
5 % to 95 % non-Condensing
Humidity
Tilt/Swivel Stand
Signal
cable
Attached(
), Detached ( O )
Attached( O ), Detached (
Power cord
Wall-out type
Regulations
710E:NON MPR
710S:MPR II
710B:TCO99
or
)
PC-outlet type
NOTE
Information in this document is
subject to change without
A13
notice.
Positive
Preset Modes
(Resolution)
1
VESA
640
x
480
37.50
75
2
VESA
800
x
600
46.88
75
3
VESA
800
x
600
53.68
85
4
VESA
1024
68.677
85
x
768
Digitally yours
Download PDF

advertising