User's Guide L1732P L1932P Make sure to read the Important Precautions before using the monitor. Keep the User's Guide(CD) in an accessible place for furture reference. See the label attached on the product and dealer when you ask for service. give the information to your Precautions Important This unit has been engineered and manufactured to ensure your personal safety, improper use may result in potential eletrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. however On Use Safety only the power cord supplied cord, make that it is certified sure with the unit. In by the you use another power national standards if not being case applicable If the power cable is faulty in any way, please contact the the nearest authorized repair service provider for a replacement. provided by the supplier. manufacturer or The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of or listed on the display. If you are not sure what type of power supply this manual you have in your home, consult with your dealer. Overloaded AC outlets and extension cords cords and broken technician for plugs. They replacement. Do not the Open may result in are a dangerous. So shock or are frayed power fire hazard. Call your service Display. There are no user There are serviceable components inside. Dangerous High Voltages inside, even when the power Contact your dealer if the display is not operating properly. is OFF. To Avoid Personal Injury : place the display on a sloping shelf unless properly secured. only a stand recommended by the manufacturer. Do not Use To Prevent Fire or Hazards: display OFF if you leave the room for more than a short period display ON when leaving the house. children from Keep dropping or pushing objects into the display's cabinet Some internal openings. parts carry hazardous voltages. Do not add accessories that have not been designed for this display. During a lightning storm or when the display is to be left unattended for an extended period of time, unplug it from the wall outlet. Always turn the of time. Never leave the A1 On Installation Do not allow anything to rest upon or roll over the power cord, and do not the display where the power cord is subject to damage. Do not use this display sink, laundry tub, in a near wet water such as near a basement, Displays are provided with ventilation generated during operation. If of heat place bathtub, washbowl, kitchen swimming pool. openings in the cabinet to allow the release these openings are blocked, built-up heat or near a failures which may result in a fire hazard. Therefore, NEVER: Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc. Place the display in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the display near or over a radiator or heat source. can cause Do not rub mar, or or strike the Active Matrix LCD with anything hard the Active Matrix LCD permanently. Do not press the LCD some as this may scratch, damage screen with your finger for a long time as this may cause afterimages. Some dot defects may appear as Red, Green or Blue spots on the screen. However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality for your LCD display. If used under any mode except the recommended resolution, some scaled or processed images may appear on the screen. However, this is characteristic of the fixed-resolution LCD panel. On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly screen because over-spraying may cause electrical shock. On on the display Repacking Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material. On Disposal The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front 2. Align 3. Insert the the hooks Warning: on base facing or Removing the stand downward the stand base with the cushion on a or base soft cloth. matching slots in the base of the monitor. hooks into slots. The tape and with locking pin may only be removed from those monitors a standing base when the base is pulled up. Otherwise, you may be injured by the protruding sections of the stand. equipped Hook Slot 4. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 5. When you desire to coin to turn the disintegrate the screw monitor from the stand base, use a counterclockwise. Screw 100 10 0 Important This illustration depicts the general picture. model of connection. Your monitor may differ from the items shown in the Once you connect the stand base, try not to disconnect it. Do not carry the product upside down holding only the stand base. The fall and get damaged or injure your foot. A3 product may Connecting the Display Before setting up the monitor, ensure that the power system, and other attached devices is turned off. to the monitor, the computer Positioning your display 1. Adjust the position Tilt Range : of the panel in various ways for maximum comfort. -5˚~25˚ Height Range : Swivel :350˚ maximun 3.15 inch (80.0mm) 80.0mm First, remove the locking pin. Landscape & Portrait : You can rotate the panel ( For more information, refer to page A6.) Make sure o 90 clockwise. not to touch the floor when the head rotates to use the Pivot function. Ergonomic It is recommended that in order to maintain position, the forward tilt angle of the an ergonomic and comfortable viewing degrees. monitor should not exceed 5 A4 Connecting the Display Using the Computer 1. Place the monitor in height a convenient, well-ventilated location of your monitor, unlock the stand lock on near your computer. To adjust top of the stand. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the connection. 3. Connect the power cord into a proper power outlet that is easily accessible and close to the Power Cord display. Signal Cable Analog signal Digital signal D-sub Varies according to model. NOTE This is a simplified representation of the This DVI rear Wall-outlet type rear view represents view. a 2 general model; your display may differ from the view shown. 1 as PC-outlet type PC MAC Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. PC 4. Press button on the front switch panel to turn the power When monitor power is turned on, the 'Self Setting Function' is executed automatically. on. Image (Only Analog Mode) NOTE 'Self Image Setting Function'? This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push the 'AUTO/SET' button on the front panel of the monitor. Otherwise, you may execute the Factory reset' option on the OSD adjustment menu. However, be aware that this option initializes all the menu items except 'Language'. ' A5 Using the Auto Pivot function This model supports Auto Pivot (automatic rotation) functions. To use this function, install the provided Forte Manager software first and then, perform Automatic setting.(Manual is the default setting when you purchase the - - product.) guide included in the CD for more details on the installation method. For the automatic setting, select Forte Manager -> Option -> Pivot -> Enable AutoPivot. Refer to the installation Notice Forte Manager software requires Microsoft Explorer 6.0 or later. The response time (speed) for the Auto Pivot function can vary depending on the video card and the PC performance, and these functions are not supported in the DOS mode. Auto Pivot Screen rotation : You can rotate the monitor screen part clockwise by 90° ※Caution : Be careful that your hands are not pressed down when the This rear . rotating screen. view represents a general model, your display may differ from the view as shown. <Pushing the screen part backwards> <Rotating clockwise> Tilt the screen part while rotating it so that the monitor does not touch the floor. A6 <When rotated by 90° > Control Panel Functions Front Panel Controls Bottom Control Function MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. - - + Buttons Button Use these buttons to select Screen Display. Lightview hot or adjust functions in the On key This feature lets you easily select the best desired NIGHT image condition optimized to the environment DAY (ambient illumination, image types etc). DAY : Bright ambient illumination NIGHT : Dark ambient illumination TEXT For text images (Word processing etc.) images in videos or movies PHOTO : For pictures or drawings NORMAL : This is under normal operating conditions : MOVIE + Button SOURCE hot : For animation key Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. A7 Control Panel Functions Control Function AUTO/SET Use this button to enter Button Display. a selection in the On Screen AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 17 inch monitor : 1280 x 1024 19 inch monitor : 1280 x 1024 Power Button Use this button to turn the Power Indicator This Indicator lights display on or up blue when the off. display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), to amber. A8 this indicator color changes On Screen Screen Display (OSD) Control Adjustment Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the To make display to stabilize for at least 30 minutes before adjustments in the On Screen Display, Press the MENU Button, then the main To access a becomes Use the control, use highlighted, the making image adjustments. follow these steps: menu of the OSD appears. -+ or Buttons. When the icon you want press the AUTO/SET Button. / + Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. - Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A9 On Screen The and Display(OSD) Selection and following table indicates all the setting menus. Main Sub menu PICTURE On Screen Adjustment Display control, adjustment, AD menu Reference To BRIGHTNESS adjust the brightness, contrast and gamma of the CONTRAST screen GAMMA COLOR PRESET 6500K To customize the color of the screen 9300K RED GREEN BLUE POSITION HORIZONTAL To VERTICAL TRACKING of the CLOCK To improve the clarity stability of the screen PHASE SETUP adjust the position screen and LANGUAGE To customize the OSD HORIZONTAL status for a user's environment POSITION VERTICAL WHITE BALANCE POWER INDICATOR FACTORY RESET : A : D : Adjustable Analog Input Digital Input NOTE The order of icons may differ depending on A10 the model (A10~A13). screen operating On Screen Selection and Display(OSD) Adjustment were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. You Press the MENU Menu Name Button, then the main menu of the OSD appears. PICTURE Sub-menus Icons Button Tip MENU -+ SET : : Exit Adjust (Decrease/Increase) : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on A11 the monitor may differ from the manual. On Screen Display(OSD) Main menu Selection and Sub Adjustment Description menu PICTURE PICTURE BRIGHTNESS To adjust the brightness of the CONTRAST To adjust the GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. screen. contrast of the screen. MENU : Exit : Decrease + : Increase SET : Select another sub-menu - COLOR COLOR PRESET Select the screen color. 6500K: Slightly reddish white. 9300K: Slightly bluish white. RED Set your own red color levels. GREEN Set your own green color levels. Set your own blue color levels. HORIZONTAL To move image left and VERTICAL To move image up and down. BLUE MENU : Exit : Decrease + : Increase SET : Select another sub-menu - POSITION POSITION MENU : Exit : Decrease + : Increase SET : Select another sub-menu - A12 right. On Screen Display(OSD) Main Selection and Sub menu Adjustment Description menu TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background.The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear the image of characters. or sharpen MENU : Exit : Decrease + : Increase SET : Select another sub-menu - SETUP LANGUAGE SETUP OSD POSITION MENU - BALANCE adjust position on the the the of the OSD window screen. output of the video card is different required specifications, the color level may deteriorate due to video signal distortion. Using this function, the SET + language in which displayed. are To If the WHITE Hz To choose the control names SETUP signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image. Activate this function when white and black colors are present in the screen. Hz MENU MENU - + - : + SET Exit POWER INDICATOR Use this function to set the power indicator on the front side of the monitor to ON or OFF. Adjust : Adjust : If you set OFF, it will go off. If you set ON at any time, the power indicator will automatically be turned SET : Select another sub-menu FACTORY RESET Restore all factory default settings except "LANGUAGE." Press the + button to reset immediately. If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be enabled the input signal is an analog signal. A13 on. only when Troubleshooting Check the No following before calling for service. image appears Is the power cord of the display connected? Check and Is the power indicator light on? Press the Power button. Is the power on and the power indicator blue or Adjust the brightness properly see if the power cord is connected to the power outlet. and the contrast. green? Is the power indicator amber? If the the display mouse or is in power pressing saving mode, try moving key on the keyboard to any bring up the screen. TrytoturnonthePC. Doyouseean"OUTOF RANGE" message the screen? on Do you see a "CHECK SIGNAL CABLE" message screen? Do you on the see a frequency range of the display. See the 'Specifications' section of this manual and configure your display again. This message appears when the signal cable between your PC and your display is not connected. Check the "OSD LOCKED" message Do you see "OSD LOCKED" when you push This message appears when the signal from the PC (video card) is out of horizontal or vertical MENU button? You can secure that they can unlock the pushing signal on cable and try again. the screen? the current control settings, so inadvertently changed. You OSD controls at any time by cannot be the MENU button for several seconds: the message "OSD UNLOCKED" will appear. A14 Troubleshooting Display image Display is incorrect Position is incorrect. Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. On the screen vertical background, bars or stripes are visible. Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon the on screen display. in Any horizontal noise appearing in any image or characters are not clearly portrayed. Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color). The Check if the screen mono or color is abnormal. signal cable is properly connected screwdriver to fasten if necessary. Make sure the video card is properly inserted in and use a the slot. Set the color setting higher than Settings. at Control Panel The screen blinks. Check if the 24 bits (true color) - screen is set to interlace mode and if it to the recommend resolution. yes, change Make sure the power voltage is high enough, It has to be higher than AC100-240V 50/60Hz. A15 Troubleshooting Have you installed the Have you installed the display driver? display driver? Be display driver from the display (or diskette) that comes with your sure to install the driver CD display. Or, you can also download the our web site: http://www.lge.com. Doyouseean "Unrecognized monitor, Plug&Play (VESA DDC) Make sure Plug&Play monitor found" message? A16 to check if the video card function. driver from supports 17inch Specifications 17 inches (43.2 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 17 inches viewable Display 0.26 pixel pitch Freq. Analog : 30 83kHz (Automatic) Digital : 30 71kHz (Automatic) Vertical Freq. 56 75Hz (Automatic) Input Form Separate TTL SOG (Sync On Green) Digital mm Horizontal Sync Input - - - Video Input 15 Signal Input pin D-Sub Connector D connector (Digital) DVI Resolution - Input Form RGB Analog (0.7Vp-p/75ohm), Digital Max Analog : VESA 1280 x 1024 @75Hz Digital : VESA 1280 x 1024 @60Hz Recommend VESA 1280 Plug&Play DDC 2B Power On Mode Sleep Mode Off Mode ≤1W Consumption x 1024@60Hz 35W : ≤1W Dimensions Width 39.00 cm / 15.35 inches &Weight (with tilt/ swivel stand) Height Depth 43.00 cm / 16.93 inches 24.20 cm / 9.53 inches Net 5.5 Tilt/Swivel Tilt -5˚~25˚ 350˚ Range Power Input Environmental Conditions Swivel AC 100-240V~50/60Hz 1.0A Operating Conditions Temperature 10˚C to 35 ˚C 10 % to 80 % non-Condensing Humidity Storage Conditions Temperature -20˚C to 60 ˚C 5 % to 95 % non-Condensing Humidity Tilt/Swivel Stand Signal cable Power cord kg (12.13 lbs) Attached( Attached( O ), Detached (O) ), Detached ( Wall-outlet type or ) PC-outlet type NOTE Information in this document is subject to change without A17 notice. 19inch Specifications 19 inches Display (48.19 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 19 inches viewable 0.294 mm pixel pitch Horizontal Sync Input Freq. Analog : 30 83kHz (Automatic) Digital : 30 71kHz (Automatic) 56 75Hz (Automatic) Separate TTL SOG (Sync On Green) Digital - - Vertical Freq. - Input Form Video Input 15 Signal Input pin D-Sub Connector D connector (Digital) DVI Resolution - Input Form RGB Analog (0.7Vp-p/75ohm), Digital Max Analog : VESA 1280 x 1024 @75Hz Digital : VESA 1280 x 1024 @60Hz Recommend VESA 1280 Plug&Play DDC 2B Power On Mode Sleep Mode ≤1W Off Mode ≤1W Consumption x 1024@60Hz 39W : Dimensions Width 43.00 cm / 16.93 inches &Weight (with tilt/ swivel stand) Height Depth 44.50 cm / 17.52 inches 24.20 cm / Net 6.4 Tilt/Swivel Tilt Range Power Input 9.53 inches kg (14.11 lbs) -5˚~25˚ Swivel 350˚ AC 100-240V~50/60Hz 1.0A Environmental Conditions Operating Conditions Temperature 10˚C to 35 ˚C 10 % to 80 % non-Condensing Humidity Storage Conditions Temperature -20˚C to 60 ˚C Tilt/Swivel Stand Attached( 5 % to 95 % non-Condensing Humidity Signal cable Power cord Attached( O ), Detached (O) ), Detached ( Wall-outlet type or ) PC-outlet type NOTE Information in this document is subject to change without A18 notice. Preset Modes 1 2 3 4 5 6 7 8 9 10 11 *12 **13 VGA VGA VGA VESA VESA VESA MAC VESA VESA MAC VESA VESA VESA (Resolution) 640 x 350 31.469 70 720 x 400 31.468 70 640 x 480 31.469 60 640 x 480 37.500 75 800 x 600 60 800 832 x 600 624 37.879 46.875 49.725 48.363 75 60 x 768 60.023 75 x 870 68.681 75 x 900 61.805 63.981 65 79.976 75 1024 x 1024 1152 1152 1280 1280 75 768 x x x 1024 1024 60 * Recommend Mode ** Indicator On Mode Sleep Mode Off Mode blue amber off Only Analog Mode Specifications Connector Pin Signal 1 8 9 16 17 24 Assignment DVI-D Connector Pin Pin Signal(DVI-D) 1 T. M. D. S. Data2- Signal(DVI-D) 16 Hot 2 T. M. D. S. Data2+ 17 T. M. D. S. Data0- 3 T. M. D. S. Data2/4 Shield 18 T. M. D. S. Data0+ 4 T. M. D. S. Data4- 19 T. M. D. S. Data0/5 Shield 5 T. M. D. S. Data4+ 20 T. M. D. S. Data5- 6 DDC Clock 21 T. M. D. S. Data5+ 22 T. M. D. S. Clock Shield 23 T. M. D. S. Clock+ 24 T. M. D. S. Clock- 7 DDC Data 8 Analog 9 T. M. D. S. Data1- 10 T. M. D. S. Data1+ 11 T. M. D. S. Data1/3 Shield 12 T. M. D. S. Data3- 13 T. M. D. S. Data3+ 14 +5V Power 15 Ground (return for +5V, H. Sync. and V. Sync.) T. M. D. S. Vertical Sync. (Transition Minimized Differential Signaling) A20 Plug Detect How to Install the VESA Standard wall This monitor meets mounting VESA-compliant mounting interface pad specifications. VESA wall mounting Connected to another object (stand type and walltype). This monitor accepts a VESAcompliant mounting interface pad.- (optional) mounted For further information, refer to the VESA Wall Mounting Instruction Guide. Kensington Security Slot- optional a locking cable that can be purchased separately at most Connected to computer A21 stores Digitally yours
advertising