LG | M197WAP-PT | LG M197WAP-PT Owner’s Manual

ENGLISH
OWNER’S MANUAL
MONITOR TV
Please read this manual carefully before operating
your set and retain it for future reference.
MONITOR TV MODELS
M197WAP
M227WAP
M237WAP
www.lge.com
CONTENTS
PREPARATION
CONTENTS
FRONT PANEL CONTROLS...............................4
BACK PANEL INFORMATION.............................5
STAND INSTALLATION
<M197WAP/M227WAP>....................................6
<M237WAP>......................................................7
DETACHING STAND
<M197WAP/M227WAP>....................................8
<M237WAP>......................................................9
WALL MOUNT: HORIZONTAL INSTALLATION.....10
DESKTOP PEDESTAL INSTALLATION............11
POSITIONING YOUR DISPLAY........................11
LOCATION.........................................................12
KENSINGTON SECURITY SYSTEM................13
ANTENNA CONNECTION.................................14
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
When connecting with a component cable......15
Connecting a set-top box with a HDMI cable..16
DVD SETUP
Connecting with a component cable...............17
Connecting with a HDMI cable........................18
VCR SETUP
Connecting with a RF cable.............................19
Connecting with a RCA cable..........................19
OTHER A/V SOURCE SETUP..........................20
PC SETUP
When connecting with a D-sub 15 pin cable.........21
BACK COVER FOR WIRE ARRANGEMENT...22
SUPPORTED DISPALY RESOLUTION............23
WATCHING TV / PROGRAMME
CONTROL
REMOTE CONTROL KEY FUNCTIONS...........24
TURNING ON THE TV......................................26
2
INSTALLATION GUIDE......................................26
PROGRAMME SELECTION..............................26
VOLUME ADJUSTMENT...................................26
ON SCREEN MENUS SELECTION AND
ADJUSTMENT...................................................27
AUTO PROGRAMME TUNING.........................28
MANUAL PROGRAMME TUNING....................29
FINE TUNING....................................................30
ASSIGNING A STATION NAME........................31
PROGRAMME EDIT..........................................32
FAVOURITE PROGRAMME..............................33
SELECTING THE PROGRAMME LIST.............34
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO)CONTROL...35
PRESET PICTURE SETTINGS.........................36
MANUAL PICTURE ADJUSTMENT..................37
PICTURE IMPROVEMENT TECHNOLOGY.....38
PICTURE RESET..............................................40
SCREEN SETUP
AUTO CONFIGURE
(RGB [PC] mode only).....................................41
MANUAL CONFIGURE
(Adjustment for screen Position).....................42
INITIALIZING
(Reset to original factory settings)...................43
SELECTING RESOLUTION..............................44
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS
- SOUND MODE.............................................45
SOUND SETTING ADJUSTMENT
- USER MODE................................................46
AUTO VOLUME LEVELER................................47
BALANCE...........................................................48
AUDIO RESET...................................................49
I/II
STEREO / DUAL RECEPTION.......................50
NICAM RECEPTION.......................................51
SPEAKER SOUND OUTPUT SELECTION....51
CLOCK SETUP..................................................52
AUTO ON/OFF TIMER SETTING.....................53
SLEEP TIMER SETTING...................................54
AUTO SHUT-OFF SETTING.............................55
CONTENTS
TIME SETTING
M227WAP........................................................69
M237WAP........................................................70
OPTION SETTING
ON-SCREEN MENU LANGUAGE SELECTION....56
KEY LOCK.........................................................57
DDC-CI(Only RGB)............................................58
POWER INDICATOR.........................................59
MODE SETTING................................................60
FACTORY RESET.............................................61
TELETEXT
SWITCH ON/OFF..............................................62
SIMPLE TEXT....................................................62
SWITCH ON/OFF..............................................63
FASTEXT...........................................................63
SPECIAL TELETEXT FUNCTIONS...................64
APPENDIX
TROUBLESHOOTING.......................................65
MAINTENANCE.................................................67
PRODUCT SPECIFICATIONS
M197WAP........................................................68
3
PREPARATION
FRONT PANEL CONTROLS
■ ■ This is a simplified representation of the front panel. The image shown may be somewhat different
from your set.
INPUT
MENU
MENU Button
OK
PREPARATION
INPUT Button
OK Button
VOLUME Buttons
VOL
PROGRAMME Buttons
PR
Power Button
Headphone Jack
4
BACK PANEL INFORMATION
■ ■ This is a simplified representation of the back panel. The image shown may be somewhat different
from your set.
<M197WAP/M227WAP>
<M237WAP>
1
2
2
3
VIDEO
RGB IN (PC)
Y
PB
(MONO) L
AUDIO R
HDMIAUDIO
IN
VIDEO
AC IN
4
7
AUDIO IN
(RGB)
VIDEO
8
AV IN
AUDIO IN
(RGB)
HDMI IN
PREPARATION
1
PR
L
R
ANTENNA/
CABLE IN
AV IN
(MONO) L
COMPONENT IN
VIDEO
AC IN
AUDIO R
RGB IN (PC)
5
PR
PB
Y
ANTENNA/
CABLE IN
AUDIO
L
R
COMPONENT IN
6
1 POWER CORD SOCKET
This set operates on AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the set on DC power.
2 AUDIO OUTPUT
Connect the audio from a Headphone Jack.
3 HDMI INPUT
Connect a HDMI signal to HDMI IN.
Or DVI (VIDEO) signal to HDMI IN with DVI to
HDMI cable.
4 RGB/DVI AUDIO INPUT
Connect the audio from a PC.
AV IN
AUDIO IN
(RGB)
HDMI IN
VIDEO
(MONO) L
AUDIO R
5 RGB INPUT (PC)
Connect the output from a PC.
VIDEO
AC IN
RGB IN (PC)
Y
PB
AUDIO
PR
L
R
ANTENNA/
CABLE IN
COMPONENT IN
6 COMPONENT INPUT
Connect a component video/audio device to
these jacks.
7 AV(AUDIO/VIDEO) INPUT
Connect audio/video output from an external
device to these jacks.
8 ANTENNA INPUT
Connect over-the-air signals to this jack.
5
PREPARATION
STAND INSTALLATION
■ ■ The image shown may be somewhat different from your set.
Carefully place the product screen side down on a
cushioned surface that will protect product and
screen from damage.
2
Insert the stand base into the product.
3
Use a coin on the bottom of the stand base and turn
the screw clockwise to tighten.
PREPARATION
1
6
<M197WAP/M227WAP>
STAND INSTALLATION
<M237WAP>
■ ■ The image shown may be somewhat different from your set.
Carefully place the product screen side down on a
cushioned surface that will protect product and
screen from damage.
2
Insert the stand base into the product.
3
Use a coin on the bottom of the stand base and turn
the screw clockwise to tighten.
PREPARATION
1
7
PREPARATION
<M197WAP/M227WAP>
DETACHING STAND
■ ■ The image shown may be somewhat different from your set.
Place the set screen side down on a
cushion or soft cloth.
2
Detach the monitor to the Stand Base by
turning the screw to the left.
3
Turn the screw by using a coin.
4
Pull the stand base.
PREPARATION
1
5
8
<M237WAP>
DETACHING STAND
■ ■ The image shown may be somewhat different from your set.
Place the set screen side down on a
cushion or soft cloth.
2
Detach the monitor to the Stand Base by
turning the screw to the left.
3
Turn the screw by using a coin.
4
Pull the stand base.
PREPARATION
1
5
9
PREPARATION
WALL MOUNT: HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
PREPARATION
10 cm
10 cm
10 cm
10 cm
10 cm
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.
1. Be sure to use screws and a wall mount that meet VESA standards.
2. Using screws longer than those recommended might damage the product.
3. Using screws that do not meet VESA standards might either damage the product or result in it coming
away from the wall. We will not be held responsible for any damage resulting from failure to follow these
instructions.
4. VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications
5. Please use VESA standard as below.
5-1) 784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm
5-2) 787.4 mm (31.0 inch) and above
* Please use VESA standard wall mount pad and screws.
< Screw Mounting Interface Dimension >
M197WAP : 100 mm x 100 mm hole spacing
M227WAP : 100 mm x 100 mm hole spacing
M237WAP : 75 mm x 75 mm hole spacing
10
Wall Mount Pad
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
10 cm
INPUT
10 cm
10 cm
MENU
OK
PREPARATION
10 cm
VOL
PR
POSITIONING YOUR DISPLAY
■ ■ The image shown may be somewhat different from your set.
Adjust the position of the panel in various ways for maximum comfort.
* Tilt range
-6° to -2°
12° to 18°
11
PREPARATION
LOCATION
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to
expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a
position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
PREPARATION
Warning:
When adjusting the angle of the screen, do not put your finger(s)
in between the head of the monitor and the stand body.
You can hurt your finger(s).
12
KENSINGTON SECURITY SYSTEM
NOTE
- The Kensington Security System is an optional accessory.
PREPARATION
- The product is equipped with a Kensington Security System connector on the back panel. Connect the
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided
with the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington
company. Kensington sells security systems for expensive electronic equipment such as notebook
PCs and LCD projectors.
NOTES
a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with product.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the monitor’s performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
<M197WAP/ M227WAP >
<M237WAP>
13
PREPARATION
■ ■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.
ANTENNA CONNECTION
■ ■ For optimum picture quality, adjust antenna direction.
■ ■ An antenna cable and converter are not supplied.
<M197WAP/ M227WAP >
PREPARATION
Multi-family Dwellings / Apartments
(Connect to wall antenna socket)
Wall
AntennaAC IN
Socket
RGB IN (PC)
AV IN
AUDIO IN
(RGB)
HDMI IN
Y
<M237WAP>
VIDEO
VIDEO
R
L
AV IN
COMPONENT IN
AUDIO IN
(RGB)
HDMI IN
VIDEO
(MONO) L
VIDEO
AC IN
ANTENNA/
CABLE IN
AUDIO
PR
PB
AUDIO R
(MONO) L
Y
RGB IN (PC)
PB
AUDIO R
AUDIO
PR
R
L
ANTENNA/
CABLE IN
COMPONENT IN
RF Coaxial Wire (75 Ω)
Outdoor
Antenna
Single-family Dwellings / Houses
(Connect to wall jack for outdoor antenna)
AV IN
AUDIO IN
(RGB)
HDMI IN
VIDEO
(MONO) L
VIDEO
AC IN
UHF
Antenna
VIDEO
(MONO) L
VIDEO
Signal
Amplifier
RGB IN (PC)
AC IN
Y
PB
Y
PB
PR
R
L
ANTENNA/
CABLE IN
COMPONENT IN
AV IN
AUDIO IN
(RGB)
HDMI IN
RGB IN (PC)
AUDIO R
AUDIO
AUDIO R
AUDIO
PR
L
R
ANTENNA/
CABLE IN
COMPONENT IN
VHF
■ ■ In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
■ ■ If signal needs to be split for two sets, use an antenna signal splitter for connection.
14
EXTERNAL EQUIPMENT SETUP
■ ■ To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
■ ■ The image shown may be somewhat different from your set.
HD RECEIVER SETUP
When connecting with a component cable
2
Connect the video outputs (Y, PB, PR) of the digital
set-top box to the COMPONENT IN VIDEO jacks on
the TV.
Connect the audio output of the digital set-top box
to the COMPONENT IN AUDIO jacks on the TV.
3
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top
box.)
4
Select Component input source using the INPUT button on the remote control
Signal
Component
480i / 576i
O
480p / 576p
O
720p
O
1080i / 1080p
O
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
VIDEO
(MONO) L
VIDEO
RGB IN (PC)
Y
AUDIO
PR
PB
R
L
ANTENNA/
CABLE IN
COMPONENT IN
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
VIDEO
(MONO) L
VIDEO
RGB IN (PC)
AUDIO R
Y
PB
EXTERNAL EQUIPMENT SETUP
1
PR
AUDIO R
AUDIO
L
R
ANTENNA/
CABLE IN
COMPONENT IN
15
EXTERNAL EQUIPMENT SETUP
Connecting a set-top box with a HDMI cable
Connect the HDMI output of the digital set-top box to
the HDMI IN jack on the TV.
1
EXTERNAL EQUIPMENT SETUP
Select HDMI input source using the INPUT button on
the remote control.
2
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top
box.)
!
!
NOTE
► ►TV can receive the video and audio signal simultaneouslywith using a HDMI cable.
?
► ►If the digital set-top box supports Auto HDMI function, the
output resolution of the source device will be automatically
TV to 1920 x 1080p.
?
► ►If the digital set-top box player does not support Auto HDMI,
you need to TV the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1920 x 1080p .
► ►We recommend less than 10 m for HDMI cable.
16
Signal
HDMI
480i / 576i
O
480p / 576p
O
720p
O
1080i / 1080p
O
VIDEO
(MONO) L
VIDEO
RGB IN (PC)
3
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
Y
PB
PR
AUDIO R
AUDIO
L
COMPONENT IN
R
ANTENNA
CABLE IN
DVD SETUP
Connecting with a component cable
1
Connect the video outputs (Y, PB, PR) of the DVD to
the COMPONENT IN VIDEO jacks on the TV.
Connect the audio outputs of the DVD to the
COMPONENT IN AUDIO jacks on the TV.
3
Turn on the DVD player, insert a DVD.
4
Select Component input source using the INPUT button on the remote control.
5
Refer to the DVD player’s manual for operating
instructions.
VIDEO
(MONO) L
VIDEO
RGB IN (PC)
Y
AUDIO
PR
PB
AUDIO R
R
L
ANTENNA/
CABLE IN
COMPONENT IN
EXTERNAL EQUIPMENT SETUP
2
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
Component Input ports
To achieve better picture quality, connect a DVD player to
the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
P-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
VIDEO
(MONO) L
VIDEO
RGB IN (PC)
Y
PB
PR
AUDIO R
AUDIO
L
R
ANTENNA/
CABLE IN
COMPONENT IN
17
EXTERNAL EQUIPMENT SETUP
Connecting with a HDMI cable
Connect the HDMI output of the DVD to the HDMI IN
jack on the TV.
1
EXTERNAL EQUIPMENT SETUP
2
Select HDMI input source using the INPUT button on
the remote control.
Refer to the DVD player’s manual for operating
instructions.
3
!
!
NOTE
► ►TV can receive the video and audio signal simultaneouslywith using a HDMI cable.
?
► ►If the digital set-top box supports Auto HDMI function, the
output resolution of the source device will be automatically
TV to 1920 x 1080p.
?
► ►If the digital set-top box player does not support Auto HDMI,
you need to TV the output resolution appropriately.
► ►To get the best picture quality, adjust the output resolution of the source device to 1920 x 1080p.
► ►We recommend less than 10 m for HDMI cable.
18
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
VIDEO
(MONO) L
VIDEO
RGB IN (PC)
Y
PB
PR
AUDIO R
AUDIO
L
COMPONENT IN
R
ANTENNA
CABLE IN
VCR SETUP
■ ■ To avoid picture noise (interference), allow adequate distance between the VCR and TV.
Connecting with a RF cable
1
Connect the ANT OUT socket of the VCR
AUDIO IN
HDMIthe
IN
to the ANTENNA IN socket on
TV. (RGB/DVI)
AV IN
VIDEO
(MONO) L
2
3
PB
Y
Connect the antenna cable toRGBthe
IN (PC) ANT IN
socket of the VCR.
PR
AUDIO
L
R
ANTENNA/
CABLE IN
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
L
COMPONENT IN
Press the PLAY button on the VCR and
match the appropriate programme
between the TV and VCR for viewing.
R
EXTERNAL EQUIPMENT SETUP
VIDEO
AUDIO R
Connecting with a RCA cable
1
AV IN
)
VIDEO
(MONO) L
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
VIDEO
(MONO) L
VIDEO
DEO
PR
AUDIO R
Connect the AUDIO / VIDEO jacks between TV and
VCR. Match the jack colours (Video = yellow, Audio
Left = white, and Audio Right = red)
2
CABLE IN a video tape
VIDEO
ANT OUT
Insert
intoS-VIDEO
the VCR
and press PLAY on
the VCR.
(Refer to the VCR owner’s manual.)
3
Select AV input source using the INPUT button on the
remote control.
AUDIO
L
R
COMPONENT IN
ANTENNA/
L
ANT IN
R
RGB IN (PC)
Y
PB
PR
AUDIO R
AUDIO
ANTENNA/
CABLE IN
R
L
COMPONENT IN
OUTPUT
SWITCH
S-VIDEO VIDEO
OUTPUT
SWITCH
L
R
ANT IN
ANT OUT
19
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
1
Connect the AUDIO/VIDEO jacks between
TV and external equipment. Match the jack
colours.
(Video = yellow, Audio Left = white, and
Audio Right = red)
EXTERNAL EQUIPMENT SETUP
20
2
3
Operate the corresponding external equipment.
Refer to external equipment operating guide.
VIDEO
(MONO) L
VIDEO
RGB IN (PC)
Select AV input source using the INPUT button on the remote control.
If connected to AV IN, select AV input
source.
AV IN
AUDIO IN
(RGB/DVI)
HDMI IN
Y
PB
AUDIO R
AUDIO
PR
ANTENNA/
CABLE IN
R
L
COMPONENT IN
VIDEO
L
R
PC SETUP
When using the remote control, aim it at the remote control sensor on the TV.
When connecting with a D-sub 15 pin cable
1
2
3
Press the INPUT button to select RGB PC.
4
Switch on the PC, and the PC screen appears on the set.
The set can be operated as a PC monitor.
RGB OUTPUT
!
!
VIDEO (MONO) L AUDIO
VIDEO
RGB IN (PC)
Connect the audio cable from the PC to the AUDIO IN
(RGB) sockets of the set.
AV IN
AUDIO IN
(RGB)
HDMI IN
Y
PB
PR
AUDIO
L
R
R
ANTENNA/
CABLE IN
COMPONENT IN
EXTERNAL EQUIPMENT SETUP
Connect the signal cable from the monitor output socket
of the PERSONAL COMPUTER to the PC input socket
of the set.
AUDIO
NOTE
► ►User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.
?
?
21
EXTERNAL EQUIPMENT SETUP
BACK COVER FOR WIRE ARRANGEMENT
Tie cables together with a cable management as shown in the illustration.
<M197WAP/ M227WAP >
EXTERNAL EQUIPMENT SETUP
<M237WAP>
22
SUPPORTED DISPALY RESOLUTION
RGB[PC] mode
M197WAP
Resolution
M227WAP / M237WAP
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
31.469
59.94
640 x 480
31.469
59.94
800 x 600
37.879
60.317
800 x 600
37.879
60.317
1024 x 768
48.363
60.0
1024 x 768
48.363
60.0
1280 x 720
47.77
59.85
1152 x 864
54.34
60.05
1360 x 768
47.71
60.02
1280 x 960
60
60
1280 x 1024
63.981
60.02
1680 x 1050
64.674
59.883
1680 x 1050
65.290
59.954
1920 x 1080
67.5
60
HDMI[DTV] mode
Resolution
EXTERNAL EQUIPMENT SETUP
640 x 480
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
720 x 480
15.73
59.94
720 x 480
31.47
59.94
720 x 480
31.50
60.00
720 x 576
31.25
50.00
1280 x 720
44.96
59.94
1280 x 720
45.00
60.00
1280 x 720
37.50
50.00
1920 x 1080
33.72
59.94
1920 x 1080
33.75
60.00
1920 x 1080
28.125
50.00
1920 x 1080
67.432
59.94
1920 x 1080
67.5
60
1920 x 1080
56.250
50
23
WATCHING TV / PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
TV/PC
MUTE
PSM
INPUT
SSM
WATCHING TV / PROGRAMME CONTROL
2
3
4
5
6
7
8
9
0
LIST
Q.VIEW
OK
VOL
SLEEP
INPUT If you press the button once, the input source OSD
will appear on screen as shown. Press the ▲/▼button and then OK button to select the desired input
source.
MUTE Switches the sound on or off.
PSM Recalls your preferred picture setting.
I/II Selects the sound output. (►p.50)
0~9 number Selects a programme.
button Selects numbered items in a menu.
PR
MENU
TV/PC Selects TV or PC mode.
SSM Recalls your preferred sound setting.
PR
VOL
POWER Switches the set on from standby or off to standby.
I/II
1
ARC/
*
TEXT
LIST Displays the programme table.
HOLD
REVEAL
24
POWER
SIZE
?
INDEX
MIX
i
MODE
TIME
UPDATE
Q.VIEW Returns to the previously viewed programme.
TV/PC
MUTE
POWER
PSM
INPUT
SSM
I/II
THUMBSTICK A
llows you to navigate the on-screen menus and
(Up/Down/Left/
Right) adjust the system settings to your preference.
Adjusts the volume. Selects a programme.
OK Accepts your selection or displays the current mode.
2
3
4
5
6
MENU Selects a menu.(► p.27)
7
8
9
SLEEP Sets the sleep timer.
0
LIST
Q.VIEW
PR
Coloured These buttons are used for teletext (on TELETEXT
buttons models only) or Programme edit.
OK
VOL
VOL
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section. (►p.62)
PR
MENU
HOLD
REVEAL
?
SLEEP
ARC/
SIZE
MIX
INDEX
i
ARC/* Selects your desired picture format.(► p.35)
MODE
*
TEXT
WATCHING TV / PROGRAMME CONTROL
1
TIME
UPDATE
Installing Batteries
■ ■ Open the battery compartment cover on the back side and install
the batteries matching correct polarity (+with +,-with -)
■ ■ Install two 1.5 V AAA batteries. Don’t mix old or used batteries with
new ones.
■ ■ Close cover.
■ ■ To remove the batteries, perform the installation actions in reverse.
25
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
When using the remote control, aim it at the remote control sensor on the TV.
1
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
■ ■ In standby mode to turn TV on, press the button
remote control and the TV will switch on.
on the TV or press the POWER buttons on the
WATCHING TV / PROGRAMME CONTROL
INSTALLATION GUIDE
1
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
Language, Auto Tuning.
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. If you close without completing the initial setting, the Instal lation Guide menu can be displayed
again.
PROGRAMME SELECTION
1
Press the ▲/▼ or NUMBER buttons to select a programme number.
VOLUME ADJUSTMENT
26
1
Press the ◄ / ► button to adjust the volume.
2
If you wish to switch the sound off, press the MUTE button.
3
You can cancel the Mute function by pressing the MUTE, ◄ / ►, SSM or I/II button.
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
1
Press the MENU button and then ▲/▼ button to display each menu.
2
Press the ► button and then ▲/▼ button to select a menu item.
3
Change the setting of an item in the sub or pull-down menu with ◄ / ► button.
You can move to a higher level menu by pressing the OK button.
Picture
Auto Tuning
Manual Tuning
Audio
Aspect Ratio
Picture Mode
Sound Mode
• Treble
50
Programme Edit
• Backlight 100
• Bass 50
Favourite Programme
• Contrast 100
• Reset
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▲▼◄► OK MENU
Setup MENU
Option
▼
▲▼◄► OK MENU
Auto Volume
Balance 0
▲▼◄► OK MENU
Picture MENU
Audio MENU
Time
Language
Clock
Key Lock
Off Time
DDC-CI
On Time
Power Indicator
Sleep Timer
Mode Setting
Auto Sleep
WATCHING TV / PROGRAMME CONTROL
Setup
Factory Reset
▲▼◄► OK MENU
Option MENU
!
?
!
▲▼◄► OK MENU
Time MENU
NOTE
► ►The OSD (On Screen Display) function enables you to adjust the screen status conveniently since it provides
graphical presentation.
► ►In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just example to help
the TV operation.
► ►In the teletext mode, menus are not displayed.
?
27
WATCHING TV / PROGRAMME CONTROL
AUTO PROGRAMME TUNING
Up to 200 TV stations can be stored by programme numbers (0 to 199). Once you have preset the stations,
you will be able to use the ▲ / ▼ or NUMBER buttons to scan the stations you have programmed.
Stations can be tuned using automatic or manual modes.
All stations which can be received are stored by this method. It is
recommended that you use Auto tuning during installation of this TV.
Setup
1
Auto Tuning
Press the MENU button and then ▲ / ▼ button to select
the Setup menu.
WATCHING TV / PROGRAMME CONTROL
2
Press the ► button and then ▲ / ▼ button to select
Auto Tuning.
3
Press the ► button and then ▲ / ▼ button to select
System
Manual Tuning
Programme Edit
Favourite Programme
▲▼◄► OK MENU
1
Setup
4
Press the ► button and then ▲ / ▼ button to select a
TV system menu;
BG: PAL B / G, SECAM B / G (Asia / NewZealand / M.
East / Africa)
I : PAL I (South Africa / Hong Kong)
DK : PAL D / K, SECAM D / K (China / Africa / CIS)
M : (Philippines)
5
Press the ▲ / ▼ button to select Storage From.
6
Press the ◄ / ► button or NUMBER buttons to select
the initial programme number.
7
Press the ▲ / ▼ button to select Search.
8
Press the ► button to begin auto tuning.
All receivable stations are stored.
AutoTuning
Tuning
Auto
Manual Tuning
► To Set
Programme Edit
Favourite Programme
▲▼◄► OK MENU
2
Auto Tuning
System
System
Storage From
BG
►
I
Search
DK
M
▲▼◄► OK MENU
3 4 5 6 7
Auto Tuning
To stop auto tuning, press the MENU button.
When auto tuning is complete, the Programme edit
menu appears on the screen. See the Programme edit
section to edit the stored programme.
9
28
Press the MENU button to move to the previous menu
screen.
C 05
BG
5
35%
Menu Stop
8
MANUAL PROGRAMME TUNING
Manual Turning lets you manually tune and arrange the stations in whatever order you desire.
Press the MENU button and then ▲ / ▼ button to select
the Setup menu.
2
Press the ► button and then ▲ / ▼ button to select
Manual Tuning.
3
Press the ► button and then ▲ / ▼ button to select
Storage.
4
Press the ◄ / ► button or NUMBER buttons to select
the desired programme number (0 to 199).
5
Press the ▲ / ▼ button to select System.
6
Press the ► button and then ▲ / ▼ button to select a
TV system menu;
BG: PAL B / G, SECAM B / G (Asia / NewZealand / M.
East / Africa)
I : PAL I (South Africa / Hong Kong)
DK: PAL D / K, SECAM D / K (China / Africa / CIS) M:
(Philippines)
7
Press the ▲ / ▼ button to select Band.
8
Press the ► button and then ▲ / ▼ button to select V/
UHF or Cable.
9
Setup
Auto Tuning
Manual Tuning
Programme Edit
Favourite Programme
1
Setup
Auto Tuning
ManualTuning
Tuning
Manual
Programme Edit
► To Set
Favourite Programme
Press the ▲ / ▼ button to select Channel.
WATCHING TV / PROGRAMME CONTROL
1
10 Press the ► button and then You can select the desired
programme number with the ◄ / ► button or NUMBER
buttons.If possible, select the programme number directly with the number buttons.
11 Press the ▲ / ▼ button to select Search.
12 Press the ◄ / ► button to commence searching. If a
station is found the search will stop.
13 Press the OK button to store it.
▲▼◄► OK MENU
2
Manual Tuning
Storage
Storage
System
►
1
Band
Channel
Fine
Search
Name
14 To store another station, repeat steps 3 to 13.
▲▼◄► OK MENU
15 Press the MENU button to move to the previous menu
screen.
3 4 5 6 7
8 9 10 11 12
29
WATCHING TV / PROGRAMME CONTROL
FINE TUNING
Normally fine tuning is only necessary if reception is poor.
Setup
1
2
Press the MENU button and then ▲ / ▼ button to select
Auto Tuning
the Setup menu.
Programme Edit
Manual Tuning
Favourite Programme
Press the ► button and then ▲ / ▼ button to select
Manual Tuning.
▲▼◄► OK MENU
WATCHING TV / PROGRAMME CONTROL
3
1
Press the ► button and then ▲ / ▼button to select Fine.
Setup
Auto Tuning
4
Press the ► button and then ◄ / ► button to fine tune
5
Press the OK button to store it.
for the best picture and sound.
ManualTuning
Tuning
Manual
Programme Edit
► To Set
Favourite Programme
▲▼◄► OK MENU
6
2
Press the MENU button to move to the previous menu
screen.
Manual Tuning
Storage
System
Band
Channel
Fine
Fine
►
◄/►
Search
Name
▲▼◄► OK MENU
3 4 5
30
ASSIGNING A STATION NAME
You can assign a station name up to five characters to each programme number.
Setup
1
2
Press the MENU button and then ▲ / ▼ button to select
Auto Tuning
the Setup menu.
Programme Edit
Manual Tuning
Favourite Programme
Press the ► button and then ▲ / ▼ button to select
Manual Tuning.
▲▼◄► OK MENU
4
Name.
Setup
Auto Tuning
ManualTuning
Tuning
Manual
Programme Edit
Press the ► button and then ▲ / ▼ button. You can use
► To Set
Favourite Programme
a blank, +, -, the number 0 to 9 and the alphabet A to Z.
5
Press the ◄ / ► button to select the position and make
▲▼◄► OK MENU
your choice of the second character, and so on.
2
Manual Tuning
6
Press the OK button to store it.
Storage
System
Band
Channel
7
Press the MENU button to move to the previous menu
screen.
Fine
Search
Name
Name
►
WATCHING TV / PROGRAMME CONTROL
3
1
Press the ► button and then ▲ / ▼ button to select
____
▲▼◄► OK MENU
3 4 5 6
31
WATCHING TV / PROGRAMME CONTROL
PROGRAMME EDIT
This function enables you to delete or skip stored programmes.
Also you can move some stations to other programme numbers.
WATCHING TV / PROGRAMME CONTROL
1
Press the MENU button and then ▲ / ▼ button to select
the Setup menu.
2
Press the ► button and then ▲ / ▼ button to select
Programme Edit.
3
Press the ► button to display the Programme edit menu.
■ Deleting a programme
1. Select a programme to be deleted with the ▲ / ▼ /
◄ / ► button.
2. Press the RED button twice.
The selected programme is deleted, all the following
programmes are shifted up one position.
■ Moving a programme
1. Select a programme to be moved with the ▲ / ▼ / ◄
/ ►button.
2. Press the Green button.
3. Move the programme to the desired programme
number with the ▲ / ▼ / ◄ / ► button.
4. Press the Green button again to release this function.
■Skipping a programme number
1. Select a programme number to be skipped with the
▲ / ▼ / ◄ / ► button.
2. Press the BLUE button. The skipped programme
turns to blue.
3. Press the BLUE button again to release the skipped
programme.
When a programme number is skipped it means that
you will be unable to select it using the ▲ / ▼ button
during normal TV viewing. If you wish to select the
skipped programme, directly enter the programme
number with the NUMBER buttons
or select it in the programme edit or table menu.
4
Press the MENU button to move to the previous menu
screen.
Setup
Auto Tuning
Manual Tuning
Programme Edit
Favourite Programme
▲▼◄► OK MENU
1
Setup
Auto Tuning
Manual Tuning
ProgrammeEdit
Edit
Programme
Favourite Programme
► To Set
▲▼◄► OK MENU
2
Programme Edit
0
C 03
0
C 03
1 BLN 03
1 BLN 03
2
C 12
2
C 12
3
S 66
3
S 66
4
S 67
4
S 67
Delete
Move
Skip
▲▼◄► OK MENU
3
32
FAVOURITE PROGRAMME
This function lets you select your favourite programmes directly.
Repeatedly press the YELLOW button to select stored favourite programmes.
1
Press the MENU button and then ▲ / ▼ button to select
2
Press the ► button and then ▲ / ▼ button to select
the Setup menu.
Setup
3
Auto Tuning
Press the ► button.
Manual Tuning
Programme Edit
Favourite Programme
4
Press the ▲ / ▼ button to select - - - - - - - -.
5
Select a desired programme with the ◄ / ► button or
▲▼◄► OK MENU
NUMBER buttons.
1
Setup
6
To store another programme, repeat steps 4 to 5.
Auto Tuning
You can store up to 8 programmes.
Programme Edit
Manual Tuning
Favourite Programme
7
___ _____
___ _____
Favourite Programme
Press the MENU button to move to the previous menu
___ _____
►
___ _____
___ _____
WATCHING TV / PROGRAMME CONTROL
Favourite Programme.
___ _____
___ _____
screen.
▲▼◄► OK MENU
2 3 4 5
33
WATCHING TV / PROGRAMME CONTROL
SELECTING THE PROGRAMME LIST
You can check which programmes are stored in the memory by displaying the programme list.
■ ■ Displaying programme l ist
Press the LIST button to display the Programme Li s t menu.
The programme list appears on the screen.
One programme list contains ten programmes as shown.
WATCHING TV / PROGRAMME CONTROL
!
?
!
NOTE
a. You may find some blue programmes. They have been
set up to be skipped by auto programming or in the programme edit mode.
b. Some programmes with the channel number shown in
the programme list indicate there is no station name
assigned.
?
■ ■ Selecting a programme in the programme l ist
Select a programme with the ▲ / ▼ / ◄ / ► button.
Then press the OK button. The TV switches to the chosen
programme number.
■ ■ Paging through a programme l ist
There are 20 programme table pages in which contain 200 pro
grammes. Pressing the ▲ / ▼ / ◄ / ► button repeatedly turns the
pages.
Programme List
0
C 03
0
1 BLN 03
2
C 12
2
C 12
3
S 66
3
S 66
4
S 67
4
S 67
▲▼◄► OK MENU
Press the LIST button to return to normal TV viewing.
34
C 03
1 BLN 03
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO)CONTROL
You can watch the screen in various picture formats; 16:9, Original, 4:3, 14:9, Zoom1, Zoom2 and Just
Scan.
If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the
screen and remain visible.
You can adjust the enlarge proportion using ▲ / ▼ button.
This function works in the following signal.
1
You can adjust Aspect Ratio in the Picture menu.
• 16:9
The following selection will allow you to
adjust thepicture horizontally, in linear proportion, to fill the entire screen(useful for
viewing 4:3 formatted DVDs).
• Zoom 1
The following selection will allow you to
view the picture without any alteration,
while filling the entire screen. However, the
top and bot tom of the picture will be
cropped.
16:9
Zoom 1 ▲▼
• Original
When your TV receives a wide screen signal it will automatically change to the picture format to be broadcast.
Original
• 4:3
The following selection will allow you to
view a picture with an original 4:3 aspect
ration, black bars will appear on both the
left and right of the screen.
Zoom 2 ▲▼
• Just Scan
Following Selection will lead to you view the
picture of best quality without loss of original picture in high resolution image.
PICTURE CONTROL
• Zoom 2
Choose Zoom 2 when you wish the picture
to be altered, both horizontally extended
and vertically cropped. The picture adopting
a compromise between alteration and
screen converage.
4:3
• 14:9
You can view a picture format of 14:9 or a
general TV programme in the 14:9 mode.
The 14:9 screen is viewed in the same way
as in 4:3, but is magnified to the left and
right.
14 : 9
Just Scan
!
?
!
NOTE
► ►You can only select 4:3,16:9 (Wide) in
Component, HDMI mode.
► ►In HDMI/Component (over 720p)mode, Just
Scan is available.
?
35
PICTURE CONTROL
PRESET PICTURE SETTINGS
Picture Mode-Preset
Picture Mode adjusts the TV for the best picture appearance. Select the preset value in the Picture Mode
menu based on the programmecategory.
Vivid, Standard, Cinema and sRGB are programmed for optimum picture reproduction at the factory.
Picture
1
Aspect Ratio
Picture Mode
Press the MENU button and then ▲ / ▼ button to select
the Picture menu.
2
• Backlight Press the ► button and then ▲ / ▼ button to select
Picture Mode.
3
100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
1
Press the ► button and then ▲ / ▼ button to select
PICTURE CONTROL
Vivid, Standard ,Cinema or sRGB.
4
Press the MENU button to move to the previous menu
screen.
100
• Contrast Picture
Aspect Ratio
PictureMode
Mode
Picture
►
• Backlight 100
• Contrast 100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
Vivid
Standard
Cinema
sRGB
2 3
!
!
NOTE
■ ■ In RGB PC mode, sRGB is Available.
36
?
?
MANUAL PICTURE ADJUSTMENT
Picture Mode-User Option
Backlight Contrast Brightness Sharpness Colour Tint To control the brightness of the screen, adjust the brightness of LCD panel.
Adjusts the difference between light and dark levels in the picture.
Increases or decreases the amount of white in the picture.
Adjusts the level of crispness in the edges between the light and dark areas of the picture.
The lower the level, the softer the image.
Adjusts intensity of all colours.
Picture
Aspect Ratio
Adjusts the balance between red and green levels.
Picture Mode
• Backlight 1
Press the MENU button and then ▲ / ▼ button to select
the Picture menu.
100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
2
Press the ► button and then ▲ / ▼ button to select
Picture Mode.
3
Press the ► button and then ▲ / ▼ button to select
4
Press the OK button and then ▲ / ▼ button to select the
desired picture option (Backlight, Contrast, Brightness,
Sharpness, Colour and Tint).
5
Press the ◄ / ► button to make appropriate adjustments.
6
Press the MENU button to move to the previous menu
screen.
1
Picture
Aspect Ratio
PictureMode
Mode
Picture
►
• Backlight 100
• Contrast 100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
Vivid
Standard
Cinema
sRGB
2 3
Picture
Aspect Ratio
Picture Mode
Vivid
Backlight • •Backlight
100
• Contrast 100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
►
PICTURE CONTROL
Vivid, Standard, Cinema or sRGB.
100
• Contrast 4 5
▲
• Backlight 100
►
▼
!
!
NOTE
■ ■ In RGB PC mode, sRGB is Available.
?
?
37
PICTURE CONTROL
PICTURE IMPROVEMENT TECHNOLOGY
You can calibrate the screen for each Picture Mode or set the video value according to the special video
screen.
You can set the video value differently for each input.
To reset to the factory default screen after making adjustments to each video mode, execute the “Picture
Reset” function for each Picture Mode.
Picture
1
Press the MENU button and then ▲ / ▼ button to select
Picture Mode
the Picture menu.
2
Press the ► button and then ▲ / ▼ button to select
Contrast,
Dynamic
Colour,
Noise
Reduction, Black Level, Film Mode or Colour
PICTURE CONTROL
Temperature.
Press the MENU button to move to the previous menu
4
screen.
100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
Press the ► button and then ▲ / ▼ button to select
Dynamic
100
• Contrast • Advanced
Advanced.
3
▲
• Backlight 1
Picture
▲
Picture Mode
• Backlight 100
• Contrast 100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
• Advanced
• Advanced
► To Set
▼
▲▼◄► OK MENU
2
Advanced
Dynamic
Contrast
Dynamic
Contrast
Dynamic Colour
►
Noise Reduction
Black Level
Off
Low
High
Film Mode
Colour Temperature
• Red 0
• Green 0
▼
▲▼◄► OK MENU
3
!
!
NOTE
■ ■ At 1080i / p Dynamic Contrast, Dynamic Colour, Noise Reduction is not enable.
38
?
?
Dynamic Contrast
(Off/Low/High)
■ ■ Adjusts the contrast to keep it at the best level according to the brightness
of the screen. The picture is improved by making bright parts brighter and
dark parts darker.
Dynamic Colour
(Off/Low/High)
■ ■ Adjusts screen colours so that they look livelier, richer and clearer.
This feature enhances hue, saturation and luminance so that red, blue,
green and white look more vivid.
Noise Reduction
(Off/Low/High)
■ ■ Reduces screen noise without compromising video quality.
Film Mode
(On/Off)
■ ■ Makes video clips recorded in film look more natural.
This feature operates only in TV, AV and Component 480i/576i mode.
Colour Temperature
(Cool/Medium/Warm)
■ ■ Choose one of three automatic colour adjustments. Set to warm to
enhance hotter colours such as red, or set to cool to see less intense
colours with more blue.
■ ■ You can control red, green, blue to adjust colour details.
PICTURE CONTROL
Black Level
(Low/High)
• Low :The reflection of the screen gets darker.
• High : The reflection of the screen gets brighter.
■ ■ Set black level of the screen to proper level.
■ ■ This function enables to select ‘Low’ or ‘High’ in the following mode: RF,
AV, Component or HDMI.
39
PICTURE CONTROL
PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
Picture
1
2
3
4
Press the MENU button and then ▲/▼ button to select
▲
• Backlight the Picture menu.
• Brightness
screen.
50
• Sharpness 70
• Colour 70
0
• Advanced
• Picture Reset
Picture Reset.
Press the MENU button to move to the previous menu
100
• Tint Press the ► button and then ▲/▼ button to select
Press the ► button to initialize the adjusted value.
100
• Contrast ▼
▲▼◄► OK MENU
1
Picture
• Backlight 100
• Contrast ▲
• Brightness 100
50
• Sharpness 70
• Colour 70
• Tint 0
• Advanced
• Picture
Reset
• Picture
Reset
► OK
▲▼◄► OK MENU
▼
PICTURE CONTROL
40
2
3
SCREEN SETUP
AUTO CONFIGURE (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not
correct, your set is functioning properly but needs further adjustment.
Auto configure
This function is for automatic adjustment of the screen position, clock, and phase The displayed image will
be unstable for a few seconds while the auto configuration is in progress.
Picture
1
2
3
Press the MENU button and then use ▲/▼ button to
select the Picture menu.
Aspect Ratio
Picture Mode
Press the ► button and then use ▲/▼ button to select
Screen.
Press the ► button and then use ▲/▼ button to select
Auto Config.
Press the MENU button to move to the previous menu
screen
50
• Sharpness 70
• Colour 70
0
▼
▲▼◄► OK MENU
1
Picture
▲
• Brightness
100
50
• Sharpness 70
• Colour 70
• Tint 5
100
• Brightness 0
• Advanced
• Picture Reset
Screen
Screen
►
To set
▼
▲▼◄► OK MENU
2
Screen
Auto
config
Auto
Config.
Manual Config.
►
PICTURE CONTROL
Press the OK button
100
• Contrast • Tint • Contrast 4
• Backlight
To Set
Reset
▲▼◄► OK MENU
3 4
41
PICTURE CONTROL
MANUAL CONFIGURE(Adjustment for screen Position)
If the picture is not clear and especially if characters are still trembling, adjust the picture phase manually.
This function works in the following mode when the signal exist : RGB PC
Picture
1
2
3
Press the MENU button and then use ▲/▼ button to
select the Picture menu.
Aspect Ratio
Picture Mode
Press the ► button and then use ▲/▼ button to select
Screen.
Press the ► button and then use ▲/▼ button to select
Manual Config.
PICTURE CONTROL
Press the ► button and then use ▲/▼ button to select
Phase, Clock, H-Position or V-Position.
(When the H-Position and V-Position be changed, Value
may differ from the aspect ratio.)
5
Press the ◄ / ► button to make appropriate adjustments.
6
100
• Brightness 50
• Sharpness 70
• Colour 70
0
▼
▲▼◄► OK MENU
1
Picture
▲
• Brightness
100
50
• Sharpness 70
• Colour 70
• Tint 0
• Advanced
• Picture Reset
Screen
Screen
►
To set
▼
▲▼◄► OK MENU
2
Screen
Auto config
Press the MENU button to move to the previous menu
100
• Contrast • Tint • Contrast 4
• Backlight
Manual
Config.
Manual
Config.
Reset
screen.
►
Phase
8
Clock
50
H-Position 50
V-Position 50
▲▼◄► OK MENU
3 4 5
42
INITIALIZING (Reset to original factory settings)
This function operates in current mode.
To initialize the adjusted value
This function works in the following mode when the signal exist : RGB PC
Picture
1
Press the MENU button and then use ▲/▼ button to
Aspect Ratio
Picture Mode
select the Picture menu.
2
Press the ► button and then use ▲/▼ button to select
• Backlight
100
• Contrast 100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
Screen.
1
3
Press the ► button and then use ▲/▼ button to select
Reset.
Picture
• Contrast ▲
100
• Brightness
70
• Colour 70
5
Press the ► button.
0
• Advanced
• Picture Reset
Screen
Screen
►
To set
▼
▲▼◄► OK MENU
Press the MENU button to move to the previous menu
screen.
2
Screen
Auto Config.
Manual Config.
Reset
Reset
►
PICTURE CONTROL
• Tint 4
50
• Sharpness To Set
▲▼◄► OK MENU
3 4
43
PICTURE CONTROL
SELECTING RESOLUTION
To view a normal picture, match the resolution of RGB mode and selection of PC mode.
This function works in the following mode: RGB[PC] mode.
Picture
1
2
3
Press the MENU button and then use ▲/▼ button to
select the Picture menu.
Aspect Ratio
Picture Mode
Press the ► button and then use ▲/▼ button to select
Screen.
100
• Contrast 100
• Brightness 50
• Sharpness 70
• Colour 70
• Tint 0
▼
▲▼◄► OK MENU
1
Press the ► button and then use ▲/▼ button to select
Picture
Resolution.
▲
• Contrast 4
• Backlight
• Brightness
100
50
Press the MENU button to move to the previous menu
• Sharpness 70
screen.
• Colour 70
• Tint 0
• Advanced
PICTURE CONTROL
• Picture Reset
Screen
Screen
►
To set
▼
▲▼◄► OK MENU
2
<Vertical resolution : 768>
<Vertical resolution : 1050>
Screen
Screen
Auto config
Auto config
Manual Config.
Resolution
Resolution
Reset
Manual Config.
►
1024 x 768
Resolution
Resolution
1280 x 768
Reset
►
1400 x 1050
1680 x 1050
1360 x 768
1366 x 768
▲▼◄► OK MENU
▲▼◄► OK MENU
3
44
3
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS - SOUND MODE
You can select your preferred sound setting; Standard, Music or Cinema.
Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate
sound options based on the programme content.
Standard, Music and Cinema are preset for optimum sound quality at the factory.
Audio
1
Sound Mode
Press the MENU button and then ▲/▼ button to select
the Audio menu.
• Treble
50
• Bass 50
• Reset
Auto Volume
Balance 2
3
Press the ► button and then ▲/▼ button to select
Sound Mode.
▲▼◄► OK MENU
1
Press the ► button and then ▲/▼ button to select
Standard, Music or Cinema.
Audio
Sound Mode
Mode
Sound
4
0
Press the MENU button to move to the previous menu
screen.
►
• Treble
50
• Bass 50
Standard
Music
Cinema
• Reset
Auto Volume
Balance 0
2 3
SOUND & LANGUAGE CONTROL
▲▼◄► OK MENU
45
SOUND & LANGUAGE CONTROL
SOUND SETTING ADJUSTMENT - USER MODE
1
Press the MENU button and then ▲/▼ button to select
the Audio menu.
Audio
Sound Mode
2
Press the ► button and then ▲/▼ button to select
• Treble
50
• Bass 50
Sound Mode.
• Reset
Auto Volume
Balance 3
Press the ► button and then ▲/▼ button to select
Standard, Music or Cinema.
4
▲▼◄► OK MENU
1
Press the OK button and then ▲/▼ button to select
Treble or Bass.
Audio
Sound Mode
Treble • •Treble
5
Press the ◄/► button to make appropriate adjustments.
• Bass SOUND & LANGUAGE CONTROL
46
50 ►
Standard
50
• Reset
Auto Volume
Balance 6
0
0
To set
Press the MENU button to move to the previous menu
screen.
▲▼◄► OK MENU
2 3 4 5
AUTO VOLUME LEVELER
Auto Volume automatically remains on the same level of volume if you change programmes.
Audio
1
Sound Mode
Press the MENU button and then ▲/▼ button to select
the Audio menu.
• Treble
50
• Bass 50
• Reset
Auto Volume
Balance 2
Press the ► button and then ▲/▼ button to select Auto
Volume.
3
0
▲▼◄► OK MENU
1
Press the ► button and then ▲/▼ button to select On
or Off.
Audio
Sound Mode
4
Press the MENU button to move to the previous menu
screen.
• Treble
50
• Bass 50
• Reset
Auto
Auto Volume
Volume
Balance ►
0
Off
On
▲▼◄► OK MENU
SOUND & LANGUAGE CONTROL
2 3
47
SOUND & LANGUAGE CONTROL
BALANCE
You can adjust the sound balance of the speakers to the preferred levels.
Audio
1
Sound Mode
Press the MENU button and then ▲/▼ button to select
the Audio menu.
• Treble
50
• Bass 50
• Reset
Auto Volume
Balance 2
Press the ► button and then ▲/▼ button to select Auto
Balance.
3
0
▲▼◄► OK MENU
1
Press the ► button and then ▲/▼ button to make
desired adjustment.
Audio
Sound Mode
4
Press the MENU button to move to the previous menu
screen.
• Treble
50
• Bass 50
• Reset
Auto Volume
Balance
Balance 0
►
▲▼◄► OK MENU
SOUND & LANGUAGE CONTROL
48
2 3
AUDIO RESET
Settings of the selected Sound Mode return to the default factory settings.
Audio
1
Sound Mode
Press the MENU button and then ▲/▼ button to select
the Audio menu.
• Treble
50
• Bass 50
• Reset
Auto Volume
Balance 2
3
0
Press the ► button and then ▲/▼ button to select
Reset.
▲▼◄► OK MENU
1
Press the ► button and then OK button
Audio
4
Press the MENU button to move to the previous menu
screen.
Standard
Sound Mode
• Treble
50
• Bass 50
• Reset
• Reset
Auto Volume
Balance ►
To set
0
▲▼◄► OK MENU
SOUND & LANGUAGE CONTROL
2 3
49
SOUND & LANGUAGE CONTROL
I/II
STEREO / DUAL RECEPTION
When a programme is selected, the sound information for the station appears with the programme number
and station name.
1
Press the I/II button to select the Multi Audio menu.
Broadcast
On Screen Display
Mono
Stereo
Dual
MONO
STEREO
DUAL I , DUAL I I , DUAL I+I I
■ ■ Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of
sound is improved. To switch back to stereo.
SOUND & LANGUAGE CONTROL
50
■ ■ Language selection for dual language broadcast
If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or
DUAL I+II.
DUAL I Sends the primary broadcast language to the loudspeakers.
DUAL I I Sends the secondary broadcast language to the loudspeakers.
DUAL I+I I Sends a separate language to each loudspeaker.
NICAM RECEPTION
If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous
Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of broadcast received.
1
When NICAM MONO is received, you can select NICAM MONO or MONO.
2
When NICAM STEREO is received, you can select NICAM STEREO or MONO.
If the stereo signal is weak, switch to MONO.
3
When NICAM DUAL is received, you can select NICAM DUAL I, NICAM DUAL II or NICAM DUAL I+II
or MONO.
In AV, Component and HDMI mode, you can select output sound for the left and right loudspeakers.
Select the sound output.
L+R : Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio R input is
sent to the right loudspeaker.
L+L : Audio signal from audio L input is sent to left and right loudspeakers.
R+R : Audio signal from audio R input is sent to left and right loudspeakers.
SOUND & LANGUAGE CONTROL
SPEAKER SOUND OUTPUT SELECTION
51
TIME SETTING
CLOCK SETUP
You must set the time correctly before using on/off time function.
If current time setting is erased by a power failure or the TV is unplugged, reset the clock.
Time
1
Press the MENU button and then ▲/▼ button to select
Clock
the Time menu.
On Time
Off Time
Sleep Timer
Auto Sleep
2
3
Press the ► button and then ▲/▼ button to select
Clock.
Press the ► button and then ▲/▼ button to set the hour.
▲▼◄► OK MENU
1
Time
Clock
Clock
4
5
TIME SETTING
52
►
––:––
Off Time
Press the ► button and then ▲/▼ button to set the min-
On Time
ute.
Auto Sleep
Press the MENU button to move to the previous menu
screen.
Sleep Timer
▲▼◄► OK MENU
2
3
3
4
AUTO ON/OFF TIMER SETTING
The Off time function automatically switches the TV to standby at a preset time.
The TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed for Two hours after.
Once the on time/off time is set, these functions operate daily at the preset time.
The Off time function overrides the On time function if both are set to the same time.
The TV must be in standby mode for the On time to work.
Time
1
Press the MENU button and then ▲ / ▼ button to select
Clock
the Time menu.
On Time
Off Time
Sleep Timer
Auto Sleep
2
Press the ► button and then ▲ / ▼ button to select On/
Off Time.
▲▼◄► OK MENU
• To cancel On / Off Time function, select Off.
1
Time
3
Press the ► button and then ▲ / ▼ button to set the
Clock
hour.
On Time
Off
Off Time
Time
►
––:––
off
Sleep Timer
Auto Sleep
4
Press the ► button and then ▲ / ▼button to set the
▲▼◄► OK MENU
5
• PR : Press the ► button and then ▲ / ▼ button to
select the programme.
• Vol : Press the ► button and then ▲ / ▼ button to
adjust volume level at switch-on.
6
2
For On Time function only
Press the MENU button to move to the previous menu
screen.
3
3
4
Time
Clock
Off Time
On
On Time
Time
►
––:––
Sleep Timer
PR
Auto Sleep
VOL
TIME SETTING
minutes.
1
30
ON
▲▼◄► OK MENU
2
3
3
4
5
53
TIME SETTING
SLEEP TIMER SETTING
You do not have to remember to switch the TV off before you go to sleep. The sleep timer automatically
switches the TV to standby after the preset time has elapsed.
Time
1
Press the MENU button and then ▲ / ▼ but ton to select
Clock
the Time menu.
On Time
Off Time
Sleep Timer
Auto Sleep
2
3
Press the ► button and then ▲ / ▼ button to select
Sleep Timer.
Press the ► button and then ▲ / ▼ button to set the
minute (Off, 10, 20, 30, 60, 90, 120, 180 or 240).
▲▼◄► OK MENU
1
Time
Clock
Off Time
On Time
Sleep
Sleep Timer
Timer 4
Press the MENU button to move to the previous menu
►
Off
Auto Sleep
screen.
▲▼◄► OK MENU
2
TIME SETTING
54
3
3
4
AUTO SHUT-OFF SETTING
If the set is switched on and there is no input signal, it will switch off automatically after 15 minutes.
Time
1
Press the MENU button and then ▲ / ▼ but ton to select
Clock
the Time menu.
On Time
Off Time
Sleep Timer
Auto Sleep
2
3
Press the ► button and then ▲ / ▼ button to select
Auto Sleep.
Press the ► button and then ▲ / ▼ button to select On
or Off.
▲▼◄► OK MENU
1
Time
Clock
Off Time
On Time
Sleep Timer
Auto
Auto Sleep
Sleep ►
Off
On
▲▼◄► OK MENU
2
3
TIME SETTING
55
OPTION SETTING
ON-SCREEN MENU LANGUAGE SELECTION
The menus can be shown on the screen in the selected language.
Option
1
Press the MENU button and then use ▲ / ▼ button to
Language
select the Opt ion menu.
DDC-CI
Key Lock
Power Indicator
Mode Setting
Factory Reset
2
Press the ► button and then use ▲ / ▼ button to select
Language.
▲▼◄► OK MENU
1
Option
3
Press the ► button and then use ▲ / ▼/ ◄ / ► button
Language
Language Key Lock
to select your desired language.
DDC-CI
► To set
Power Indicator
Mode Setting
Factory Reset
4
Press the OK button
▲▼◄► OK MENU
5
Press the MENU button to move to the previous menu
screen.
OPTION SETTIN
56
2
KEY LOCK
The TV can be set so that the remote control is needed to control it.
This feature can be used to prevent unauthorized viewing.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
1
Option
Press the MENU button and then ▲ / ▼ button to select
Language
the Option menu.
Key Lock
DDC-CI
Power Indicator
Mode Setting
2
Factory Reset
Press the ► button and then ▲ / ▼ button to select Key
Lock.
▲▼◄► OK MENU
1
3
Press the ► button and then ▲ / ▼ button to select On
or Off.
Option
Language
Key Lock
Lock
Key
DDC-CI
►
Off
On
Power Indicator
4
Press the MENU button to move to the previous menu
Mode Setting
Factory Reset
screen.
▲▼◄► OK MENU
2
3
OPTION SETTIN
!
?
!
NOTE
► ►In Key Lock ‘On’, if the TV is turned off, press the / I button on the TV or POWER buttons on the remote
control.
► ►With the Key Lock On, the display ‘Key Lock On’ appears on the screen if any button on the front panel is
pressed while viewing the TV.
?
57
OPTION SETTING
DDC-CI(Only RGB)
DDC-CI (Display Data Channel Command Interface) is a communication protocol for communications
between PC and set.
DDC-CI makes it possible to adjust and setup detailed functions on PC instead of the set OSD.
Set can be adjusted with PC by connecting communication between PC and set when DDC-CI is ON, and
when DDC-CI is OFF set cannot be adjusted with PC because communication between PC and set is disconnected.
Option
1
Press the MENU button and then ▲ / ▼ button to select
Language
the Option menu.
DDC-CI
Key Lock
Power Indicator
Mode Setting
Factory Reset
2
Press the ► button and then ▲ / ▼ button to select
DDC-CI.
▲▼◄► OK MENU
1
3
Press the ► button and then ▲ / ▼ button to select On
or Off.
Option
Language
Key Lock
DDC-CI
DDC
- CI
Power Indicator
4
Press the MENU button to move to the previous menu
►
Off
On
Mode Setting
Factory Reset
screen.
2 3
OPTION SETTIN
58
POWER INDICATOR
It is function to control of LED(turn on/off).
Option
1
Language
Press the MENU button and then ▲/▼ button to select
the Option menu.
Key Lock
DDC-CI
Power Indicator
Mode Setting
2
Factory Reset
Press the ► button and then ▲/▼ button to select
Power Indicator.
▲▼◄► OK MENU
3
Press the ► button and then ▲/▼ button to select On or
Off .
1
Option
Language
4
Press the MENU button to move to the previous menu
screen.
Key Lock
DDC-CI
Power
Power Indicator
Indicator
Mode Setting
► To set
Factory Reset
▲▼◄► OK MENU
2
OPTION SETTIN
59
OPTION SETTING
MODE SETTING
We recommend setting the set to “Home Use” mode for the best picture in your home environment.
“Store Demo” mode is an optimal setting for displaying at stores.
1
Option
Press the MENU button and then ▲ / ▼ button to select
Language
the Option menu.
Key Lock
DDC-CI
Power Indicator
Mode Setting
2
Factory Reset
Press the ► button and then ▲ / ▼ button to select
Mode Setting.
▲▼◄► OK MENU
3
1
Press the ► button and then ◄ / ► button to select
Store Demo or Home Use.
Option
Language
Key Lock
DDC-CI
4
Press the MENU button to move to the previous menu
screen.
Power Indicator
► To set
Stting
Mode Setting
Factory Reset
2
Mode Setting
Choose the setting mode you want
OPTION SETTIN
60
Store Demo Home Use
Select (Home Use) to use this TV at home
To use this TV at store
select (Store Demo)
◄► OK MENU
3
FACTORY RESET
Use to quickly reset all the menu options to their original factory preset values.
This function deletes all TV programmes.
When the Factory Reset is completed, you must restart the Installation Guide.
1
Option
Press the MENU button and then ▲ / ▼ button to select
Language
the Option menu.
Key Lock
DDC-CI
Power Indicator
Mode Setting
2
Factory Reset
Press the ► button and then ▲ / ▼ button to select
Factory Reset.
▲▼◄► OK MENU
3
1
Press the ► button and then ▲ / ▼ button to select Yes
or No.
Option
Language
Key Lock
DDC-CI
4
Press the MENU button to move to the previous menu
screen.
Power Indicator
Mode Setting
Factory Reset
Reset
Factory
► To set
2
Factory Reset
No
◄► OK MENU
3
OPTION SETTIN
Yes
61
TELETEXT
This feature is not avai lable in al l countries.
Teletext is a free service broadcast by most TV stations which
gives up-to-the-minute information on news, weather, television
programmes, share prices and many other topics.
TV/PC
MUTE
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a
number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods allowing quick and easy selection of teletext information.
POWER
PSM
INPUT
SSM
I/II
1
2
3
4
5
6
7
8
9
0
LIST
Q.VIEW
PR
SWITCH ON/OFF
OK
VOL
Press the TEXT button to switch to teletext. The initial page or last
page viewed appears on the screen.
Two page numbers, TV station name, date and time are displayed
on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The previous mode
reappears.
VOL
PR
MENU
HOLD
REVEAL
?
SLEEP
ARC/
SIZE
MIX
INDEX
i
MODE
*
TEXT
TIME
UPDATE
SIMPLE TEXT
Page selection
1 Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press
a wrong number, you must complete the three digit number and then re-enter the correct page number.
2 The ▲ / ▼ button can be used to select the preceding or following page.
Programming a colour button in LIST mode
TELETEXT
62
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
M
button to switch to LIST mode.
Four teletext page numbers of your choice can be colour coded and easily selected by pressing the corresponding coloured button on the remote control handset.
1 Press a coloured button.
2 Using the NUMBER buttons, select the page you wish to programme.
3 Press the OK button. The selected page is stored as the selected page number, blinking once to confirm this.
From now on, you can select this page with the same coloured button.
4 The three other coloured buttons are programmed in this way.
SWITCH ON/OFF
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field
denotes the next group and the blue field indicates the next block.
■ ■ Block / group / page selection
1 With the blue button you can progress from block to block.
2 Use the yellow button to proceed to the next group with automatic overflow to the next block.
3 With the green button you can proceed to the next existing page with automatic overflow to the next group.
Alternatively the ▲ button can be used.
4 The red button return to the previous selection. Alternatively the ▼ button can be used.
■ ■ Direct page selection
As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the
NUMBER buttons in TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button.
■ ■ Page selection
1 Press the i button to select the index page.
2 You can select the pages which are colour coded along the bottom line with corresponding coloured buttons.
3 As with SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER
buttons in FASTEXT mode.
4 The ▲ / ▼ button can be used to select the preceding or following page.
TELETEXT
63
TELETEXT
SPECIAL TELETEXT FUNCTIONS
■ ■ TIME
When viewing a TV programme, press this button to display the time at the topright hand corner of the screen.
Press this button again to remove the display.
In the teletext mode, press this button to select a sub page number. The sub page number is displayed at
the bottom of the screen. To hold or change the sub page, press the RED / GREEN, ▲ / ▼ or NUMBER
buttons.
Press again to exit this function.
■ ■ SIZE
Selects double height text.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of the page.
Press this button again to return to the normal display.
■ ■ UPDATE
Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at the top
left hand corner of the screen. When the updated page is available then display will change to the page
number. Press this button again to view the updated teletext page.
?
■ ■ REVEAL
Press this button to display concealed information, such as solutions to riddles or puzzles.
Press this button again to remove the information from the display.
i
■ ■ INDEX
Select the each index page.
TELETEXT
64
■ ■ HOLD
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The
number of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this
button is pressed the stop symbol is displayed at the top left-hand corner of the screen and the automatic
page change is inactive. To continue press this button again.
■ ■ MIX
Displays the teletext pages superimposed on the TV picture.
To switch the TV picture off press this button again.
APPENDIX
TROUBLESHOOTING
The TV does not operate properly
The remote control
does not work
■ ■ Check to see if there is any object between the TV and the remote
control causing an obstruction.
■ ■ Are batteries installed with correct polarity (+ to +, - to -)?
■ ■ Install new batteries.
Power is suddenly
turned Off
■ ■ Is the sleep timer set?
■ ■ Check the power control settings. Has the Power supply been interrupted.
■ ■ The TV goes into Standby mode automatically if no signal is received
and no operation is performed for 15 minutes.
The Video function is not working
No picture &
No sound
■
■
■
■
■
■ Check whether the TV is switched on.
■ Try another channel. The problem may be with the broadcast.
■ Is the power cord inserted correctly into the mains?
■ Check your antenna direction and/or location.
■ Test the mains outlet by plugging another TV into the same outlet.
is normal, the image is muted during the TV startup process.
Picture appears slowly ■ ■ This
Please contact your service center, if the picture has not appeared
after switching on
after five minutes.
No or poor colour
or poor picture
■
■
■
■
■
■ Adjust Colour in menu option.
■ Allow a sufficient distance between the TV and the VCR.
■ Try another channel. The problem may be with the broadcast.
■ Are the video cables installed properly?
■ Activate any function to restore the brightness of the picture.
Horizontal/vertical
■ ■ Check for local interference such as an electrical appliance or power
tool.
bars or picture shaking
Poor reception on
some channels
■ ■ Check antenna (Change the position of the antenna).
APPENDIX
Lines or streaks in
pictures
■ ■ Station or cable channel experiencing problems, tune to another station.
■ ■ Station signal is weak, reposition the antenna to receive weaker stations.
■ ■ Check for sources of possible interference.
65
APPENDIX
The Audio function is not working
Picture OK &
No sound
No output from one
of the speakers
■
■
■
■
■
■
■
■
Press the VOL ◄ or ► (or +) button.
Sound muted? Press MUTE button.
Try another channel. The problem may be with the broadcast.
Are the audio cables installed properly?
■ ■ Adjust Balance in menu option.
■ ■ A change in ambient humidity or temperature may result in an unusu-
Unusual sound from
al noise when
inside the TV
■ ■ the TV is switched on or off and does not indicate a fault with the TV.
■
■
■
Picture ok & No sound
■
■
■ Check whether volume is “0”.
■ Check sound muted.
■ HDMI cable installed properly.
■ Head phone cable installed properly.
■ Check sound format. Not supply to bitstream and compressed sound
format.
NO image appear.
Do you see an “OUT ■ ■ This message appears when the signal from the PC(video card) is out
off horizontal or vertical frequency range of the display. See the ‘
OF RANGE” message
Product Specifications’ section of this manual and configure you dison the screen?
play again.
APPENDIX
66
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV.
Caution : Be sure to swith the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1 A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then
use it to wipe the screen.
2 Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching
on.
Cleaning the Cabinet
!
?
■ ■ To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■ ■ Do not to use a wet cloth.
!
Extended
Absence
?
CAUTION
► ►If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to
protect against possible damage from lightning or power surges.
APPENDIX
67
APPENDIX
PRODUCT SPECIFICATIONS
M197WAP
470.1 mm Wide (18.51 inch) TFT (Thin Film Transistor)
Screen Type
LCD Panel
Visible diagonal size: 470.1 mm
Pixel Pitch
Video Signal
LCD (Liquid Crystal Display) Panel
0.30 mm (H) x 0.30 mm (V)
Max. Resolution
1366 x 768 @ 60 Hz
Recommended Resolution
1360 x 768 @ 60 Hz
Horizontal Frequency
Vertical Frequency
Synchronization Type
Input Connector
30 kHz to 61 kHz
56 Hz to 61 Hz
Separate Sync, Digital
CVBS, TV, D-Sub Analog, HDMI, PC Audio In, component
Rated Voltage
AC 100-240 V~ 50 / 60 Hz 0.6 A
On Mode : 25 W (typ.)
Power
Power Consumption
Sleep Mode 1 W (RGB)
Off Mode 0.5 W
Tilt
Tilt Range
Dimensions (Width x Height x Depth)
Weight
conditions
APPENDIX
68
454.7 mm x 362.8 mm x 193.2 mm
(17.90 inch x 14.28 inch x 7.61 inch)
3.5 kg (7.72 lb)
Operating Temperature
Environmental
-5° to 15°
Operating Humidity
Storage Temperature
Storage Humidity
10 °C to 35 °C
20 % to 80 %
-10 °C to 60 °C
5 % to 90 %
■ ■ The specifications shown above may be changed without prior notice for quality improvement.
M227WAP
546.86 mm Wide (21.53 inch) TFT (Thin Film Transistor)
Screen Type
LCD Panel
Visible diagonal size: 546.86 mm
Pixel Pitch
Video Signal
LCD (Liquid Crystal Display) Panel
0.248 mm (H) x 0.248 mm (V)
Max. Resolution
1920 x 1080 @ 60 Hz
Recommended Resolution
1920 x 1080 @ 60 Hz
Horizontal Frequency
Vertical Frequency
Synchronization Type
Input Connector
30 kHz to 69 kHz
56 Hz to 61 Hz
Separate Sync, Digital
CVBS, TV, D-Sub Analog, HDMI, PC Audio In, component
Rated Voltage
AC 100-240 V~ 50 / 60 Hz 0.9 A
On Mode : 45 W (typ.)
Power
Power Consumption
Sleep Mode 1 W (RGB)
Off Mode 0.5 W
Tilt
Tilt Range
Dimensions (Width x Height x Depth)
Weight
conditions
519.8 mm x 400.5 mm x 193.2 mm
(20.46 inch x 15.77 inch x 7.61 inch)
4.5 kg (9.92 lb)
Operating Temperature
Environmental
-5° to 15°
Operating Humidity
Storage Temperature
20 % to 80 %
-10 °C to 60 °C
5 % to 90 %
■ ■ The specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
Storage Humidity
10 °C to 35 °C
69
APPENDIX
M237WAP
584.2 mm Wide (23 inch) TFT (Thin Film Transistor)
Screen Type
LCD Panel
Visible diagonal size: 584.2 mm
Pixel Pitch
Video Signal
LCD (Liquid Crystal Display) Panel
0.265 mm (H) x 0.265 mm (V)
Max. Resolution
1920 x 1080 @ 60 Hz
Recommended Resolution
1920 x 1080 @ 60 Hz
Horizontal Frequency
Vertical Frequency
Synchronization Type
Input Connector
30 kHz to 69 kHz
56 Hz to 61 Hz
Separate Sync, Digital
CVBS, TV, D-Sub Analog, HDMI, PC Audio In, component
Rated Voltage
AC 100-240 V~ 50 / 60 Hz 1 A
On Mode : 50 W (typ.)
Power
Power Consumption
Sleep Mode 1 W (RGB)
Off Mode 0.5 W
Tilt
Tilt Range
Dimensions (Width x Height x Depth)
Weight
conditions
APPENDIX
70
560.8 mm x 427 mm x 193.2 mm
(20.08 inch x 16.81 inch x 7.61 inch)
5.6 kg (12.35 lb)
Operating Temperature
Environmental
-5° to 15°
Operating Humidity
Storage Temperature
Storage Humidity
10 °C to 35 °C
20 % to 80 %
-10 °C to 60 °C
5 % to 90 %
■ ■ The specifications shown above may be changed without prior notice for quality improvement.
Make sure to read the Safety Precautions before
using the product.
Keep the User’s Guide(CD) in an accessible
place for furture reference.
The model and serial number of the SET is
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
Download PDF

advertising