LG | HBS-810 | Owner's Manual | LG HBS-810 Owner's manual

LG HBS-810 Owner's manual
繁體中文
English
HBS-810 使用手冊
Bluetooth® 立體聲耳機
Rev 1.0 TW
保留一切權利。
LG Electronics Inc., 2016
備註:為了讓 HBS-810 發揮最佳效能,並避免損壞或發生不當
使用的情況,在使用 HBS-810 之前,請先仔細閱讀本手冊中
的所有資訊。
任何因印刷錯誤或資訊不正確而須對本手冊進行的修改或變更,
應由 LG Electronics Inc. 進行。 本手冊的所有資訊若有變更,將不
另行通知。
簡介
繁體中文
LG TONE ULTRATM (HBS-810) 為使用 Bluetooth® 技術的輕量型無線耳機。
本產品可搭配支援 A2DP 或免持藍牙操作模式的裝置,作為音訊配件使用。
包裝盒內容
額外的耳塞套
(1 組 - 小型)

HBS-810
(已安裝中型耳塞套)
使用手冊
*USB 充電連接線
*實際產品設計可能與本手冊所顯示的圖片不同。
! 注意事項
請務必使用正版 LG Electronics 配件。 使用非正版配件可能
損壞產品並導致保固失效。
2
零件說明
繁體中文
耳機
充電連接埠
LED 指示燈
通話按鈕
麥克風
耳塞 (左)
快轉/倒轉易控鈕
播放/暫停/停止按鈕
耳塞 (右)
電源開關
音量易控鈕 (+/-)
3
如何使用
繁體中文
開機/關機
電池狀態提示
- 將電源開關滑動至 [ON] 或 [OFF] 位置。
- 將音量易控鈕滑動至 [-] 位置約 1 秒,然
後查看耳機的電池狀態。
充電中
- 連接充電器時,不論耳機為開機或關機狀
態,耳機電源都會關閉。
- 充電時,LED 指示燈會持續亮起紅
燈。 充電達 80% 以上時,指示燈會顯
示紫色燈。
- 裝置充飽電時,LED 指示燈會持續亮
起藍燈。
電量不足
- 每 2 分鐘出現一次電量不足提示。
- 若電池未充電,耳機電源則會關閉。
4
電池狀態
高
中
低
語音提示 電量充足 電量中等 電量不足
LED 指
閃藍燈
閃紫燈
閃紅燈
示燈
注意:配對時,某些行動裝置可能會在螢
幕頂端顯示耳機的電池電量。
如何使用
配對
第一次使用耳機之前,您必須先將耳機與
已啟用藍牙功能的裝置進行配對。
1) 簡單配對
1. 將電源開關滑動至 [ON] 的位置。
2. 若是首次配對裝置,或者耳機偵測
不到先前配對的裝置,耳機會進入
「配對」模式。 LED 指示燈會持續
亮起藍燈。
繁體中文
收線式耳塞
- 拉動耳塞即可將耳塞線拉長至所需長度。
- 若要縮回耳塞,請稍微將耳塞線向外拉,
耳塞即會自動縮回定位。
- 如果耳塞沒有縮回,請將耳塞整個向外拉
來縮回耳塞。
3. 確
認您可偵測到想配對的裝置。 在
[藍牙] 功能表下搜尋或新增裝置。
4. 從
裝置清單中選擇 [LG HBS810]。
5. 如
果系統要求 Pass/PIN 碼,請輸入
0000 (4 個零)。
6. 裝
置配對後,您將會聽到「Your
headset paired.」(您的耳機已配對)。
連線後會發出震動提示。
注意:如果 3 分鐘內沒有進行配對,
耳機電源將會自動關閉。
2) 手動配對 (與其他手機配對或重新配對)
1. 在
電源關閉時,按下通話按鈕並
同時將電源開關滑動至 [ON] 位
置 2 秒鐘。
5
如何使用
繁體中文
2. 當耳機進入「配對」模式,LED 指
示燈會持續亮起藍燈。 重複「簡單
配對」步驟 3 到 6。
注意:連線後會發出震動提示。
注意:耳機同時連線到兩個行動裝置時
(多點連接),是在主要行動裝置上使用耳
機通話功能。
注意:若耳機無法透過「簡單配對」連線
到主要手機,則會進入「配對」模式。
進階多點連接功能
耳機能同時連線到兩個裝置。 這能讓您在
兩支連線的手機上,自由地在通話之間使
用來電等候。
與兩個裝置配對
- 首先,將耳機與要作為次要裝置使用,
且已啟用藍牙功能的行動裝置配對 (請參
閱「配對指示」)。
- 配對後,關閉耳機電源。
- 在電源關閉時,按下通話按鈕並同時將電
源開關滑動至 [ON] 位置 2 秒鐘,以進入
「手動配對」模式。
- 將耳機與另一個已啟用藍牙功能的行
動裝置進行配對並連線。 (這將是您的
主要裝置)。
- 主要行動裝置與耳機配對並連線後,將耳
機重新連線到一開始配對的行動裝置。
6
通話
- 「語音撥號」與「最後撥出號碼重撥」
功能是在主要行動裝置 (或是最後撥出電
話的行動裝置) 上使用。
來電等候
- 通話時,按下通話按鈕 1 秒鐘即可接
聽來電。
- 若要在 2 個進行中通話之間切換,請按下
通話按鈕 1 秒鐘。
- 若要結束兩邊通話,請短按通話按鈕。
- 如果兩個配對的行動裝置同時接到來電,
根據預設,耳機將選擇主要裝置。

自動重新連線
通話
- 耳機電源開啟時,若耳機與主要行動裝置
位於連線範圍內,則會自動重新連線。
- 次要行動裝置則需手動連線。 從 [藍牙]
功能表的裝置清單中選擇 [LG HBS810],
然後進行配對。
注意:連線後會發出震動提示。
接聽來電
- 接到來電時,耳機會響鈴並震動。
- 將音量易控鈕短暫滑動至 [-] 位置,
即可停止震動。
注意:震動功能停用後,耳機將不會
震動。
- 短按通話按鈕即可接聽來電。
不在連線範圍內
- 配對的裝置之間若距離 33 英呎 (10 公尺)
以上,耳機和行動裝置將會中斷連線,
並且耳機會以震動提示您。
注意:若要關閉裝置震動功能,請將音量
易控鈕滑動至 [+] 位置,並按住 2 秒鐘。
- 若耳機與行動裝置在回到要求範圍內時沒
有自動重新連線,請短按耳機上的通話按
鈕來手動重新連線。
- 進行多重連線和串流時,若非使用中的配
對裝置超出範圍,則會中斷連線。 耳機
將提示您一次,但不會嘗試重新連線。
繁體中文
如何使用
轉接電話
- 您可以按耳機上的播放/暫停/停止按鈕
兩次,將電話手動轉接到耳機,或將耳
機的電話轉接到裝置 (行動裝置必須與
耳機配對)。
7
如何使用
繁體中文
語音撥號
- 短按通話按鈕即可啟動「語音命令」。
注意:如果您的行動裝置不支援語音撥
號,此動作可能會啟動「最後撥出號碼
重撥」。
最後撥出號碼重撥
- 按住通話按鈕 1 秒鐘即可啟動「最後撥出
號碼重撥」。
耳機會發出嗶聲,然後再撥打最後撥
出的號嗎。
結束通話
- 短按通話按鈕。
來電等候
- 按下通話按鈕 1 秒鐘,即可接聽第二通來
電但不掛斷第一通電話。 按下通話按鈕
1 秒鐘,即可回到第一通電話。
- 短按通話按鈕,即可結束兩個通話。
8
拒接來電
- 行動裝置鈴響時按下通話按鈕 2 秒鐘,
即可啟動「拒接來電」功能。
注意:這些功能可能不適用於所有行動裝
置。 如需使用這些功能的詳細資訊,請參
閱行動裝置的使用手冊。
麥克風靜音
- 將音量易控鈕滑動至 [+] 位置,並同時將
快轉/倒轉易控鈕滑動至倒轉位置
1 秒鐘,即可在交談期間將麥克風靜音/
解除靜音。
小心:為了您的安全,駕駛時請勿使用
此功能。
音量控制
震動控制
- 將音量易控鈕滑動至 [+] 或 [-] 位置,
即可調整喇叭音量。
小心:長時間以高音量聆聽音樂,可能會
造成聽力受損或喪失。 為避免此情況,
當您使用 6 級以上的音量時,耳機會發
出警告嗶聲。
- 若要啟動或停用裝置震動功能,請將音量
易控鈕滑動至 [+] 位置 2 秒鐘。 您會在啟
動或停用震動時,聽到「Vibrate on」(震
動開啟) 或「Vibrate off」(震動關閉)。
- 震動功能停用時,耳機在收到來電或超
出配對的行動裝置的連線範圍內時將
不會震動。
- 裝置電源開啟時,震動功能將自動重
新啟動。
注意:耳機與行動裝置配對時,即使震
動功能已停用,耳機仍會在配對完成
時震動。
繁體中文
如何使用
9
如何使用
繁體中文
音訊串流
播放
- 短按播放/暫停/停止按鈕。
暫停
- 播放音樂時,短按播放/暫停/停止按鈕。
停止
- 播放音樂時,按住播放/暫停/停止按
鈕 1 秒鐘。
下一首歌曲
- 將快轉/倒轉易控鈕快速滑動至快轉
位置。
上一首歌曲
- 將快轉/倒轉易控鈕快速滑動至倒轉
位置。
10
快轉
- 將快轉/倒轉易控鈕滑動至快轉位置
並按住。
倒轉
- 將快轉/倒轉易控鈕滑動至倒轉位置
並按住。
如何使用
等化器
- 播放音樂時,按下播放/暫停/停止按鈕兩
次,可在低音強化 (預設)、標準、高音提
升之間切換。
注意:耳塞套大小可能會影響您聽到的
低音音域。

aptX®

Tone & Talk
繁體中文

TM
HBS-810 藍牙耳機支援在 AndroidTM 裝置上
讀出文字訊息
若要下載此應用程式,請在 Google PlayTM*
中搜尋 Tone & Talk 或掃描 QR 碼。 請按照
安裝指示操作。
*Google Play 是 Google, Inc. 的商標。
- 耳機配備 aptX 技術,可確保透過藍牙傳
輸的音訊內容不僅順暢且音質清晰。
- 只要來源裝置支援,aptX 即會自動啟用。
11
如何使用
繁體中文
功能
目前時間提示
動作
將快轉/倒轉易控鈕滑動至快轉位置 1 秒鐘。
讀出最新的文字訊息或多
將快轉/倒轉易控鈕滑動至倒轉位置 1 秒鐘。
媒體訊息
12
指定聯絡人
1. 在應用程式的耳機通話設定中選擇指定聯絡人。
2. 若要撥打電話給指定聯絡人,請按下耳機的通話按鈕兩次。
最愛聯絡人
1. 在應用程式的耳機通話設定中選擇最愛聯絡人。
2. 按下耳機的通話按鈕兩次。
3. 使用快轉/倒轉易控鈕選擇聯絡人。
4. 若要撥打電話給最愛聯絡人,請按下通話按鈕兩次。
通話記錄
1. 在應用程式的耳機通話設定中選擇 [通話記錄]。
2. 按下耳機的通話按鈕兩次。
3. 使用快轉/倒轉易控鈕選擇聯絡人。
4. 若要撥打電話給聯絡人,請按下通話按鈕兩次。
LED 指示燈
運作中
充電中
耳機狀態
指示燈
開機
藍色 LED 燈閃爍 4 次。
關機
藍色 LED 燈閃爍 4 次,然後電源關閉。
「配對」模式
持續亮藍色 LED 燈。
耳機/免持操作模式
已連線
來電接通
藍色 LED 燈每 5 秒閃爍 1 次。
充電中
充電完成
繁體中文
功能
藍色 LED 燈每 5 秒閃爍 1 次。
持續亮紅色 LED 燈,並會在充電至 80% 以上時轉
為紫色。
持續亮藍色 LED 燈。
13
疑難排解
繁體中文
問題
沒有開機
無法與 LG 藍牙耳機
HBS-810 通訊
無法將 HBS-810 與藍
牙裝置配對
音量太小 (喇叭)
14
可能原因
可能的解決方法
檢查耳機的電池是否已充滿。
為電池充電。
檢查您嘗試配對的行動裝置是否支
援耳機或免持藍牙操作模式。
判斷您的行動裝置是否支援耳機或免
持藍牙操作模式。
檢查耳機的電池電力是否不足。
為電池充電。
檢查並確認耳機電源已開啟。
將電源開關滑動至 [ON] 位置,即可
開啟耳機電源。
檢查並確認耳機處於「配對」模式。
在電源關閉時,按下通話按鈕並同
時將電源開關滑動至 [ON] 位置 1 秒
鐘,可將耳機手動設定為「手動配
對」模式。
檢查喇叭音量。
調高音量。
規格
說明
4.1 (耳機/免持裝置/A2DP 操作模式)
電池
電池 3.7 V/220 鋰離子聚合物
通話時間
多達 17 小時
音樂播放時間
多達 13 小時
待機時間
多達 550 小時
充電時間
低於 2 小時
額定輸入功率
DC 4.75 V ~ 5.3 V,400 mA
操作溫度
-10°C ~ 60°C
尺寸/重量
147 公釐 (寬) x 164 公釐 (長) x 14.9 公釐 (高) / 41 公克
繁體中文
項目
藍牙版本
15
注意事項
繁體中文
請勿任意拆解、調整或維修產品。
請勿將產品置於過熱處或可燃物附近。
請勿任意更換電池,因為可能會爆炸。
如果使用不相容的充電器,可能損壞產品。
請確認嬰兒或孩童不會吞食產品的磁鐵或小型配件。
如果您體內植入醫療裝置,請在使用前聯絡您的醫師。
請勿用力拉扯耳機線。
• 為確保安全,請勿移除併入產品內的電池 。
• 鋰離子聚合物電池是一種可能造成人身傷害的危險元件。
• 將電池更換為不合格的產品可能會導致您的裝置受損。
• 請勿自行更換電池。電池可能已損毀,導致過熱及令人體受傷。電池必須由許可的服務供應
商更換。電池應回收或與家居廢物分開棄置。
• 請勿從高處摔落產品。
• 請確認此產品未接觸水、酒精或苯。
• 請勿將產品置於潮濕或多塵的地方。
• 請勿在產品上放置重物。
• 產品不具防水功能 避免潮濕環境和水。
• 如果產品暴露在過多的汗水中,請擦乾產品。
• 請保持耳機耳塞清潔。
16
確認宣告
本裝置符合 FCC 規則第 15 節。
必須遵守下列兩個操作條件:
(1) 本
裝置不得引起有害干擾,且
(2) 本
裝置必須可承受接收到的干擾,包括
可能導致預期外操作之干擾。
依據低功率電波輻射性電機管理辦法
經型式認證合格之低功率射頻電機,非經許
可,公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及
干擾合法通信;經發現有干擾現象時,應
立即停用,並改善至無干擾時方得繼續使
用。 前項合法通信,指依電信法規定作業
之無線電通信。 低功率射頻電機須忍受合
法通信或工業、科學及醫療用電波輻射性電
機設備之干擾。
重要注意事項:
為了符合 FCC RF 放射物需求,不得對天
線或裝置進行變更。 若對天線或裝置進行
任何變更,可能導致裝置超出 RF 放射物要
求,並中止使用者操作裝置之授權。
繁體中文
使用者 FCC 聲明:
符合性聲明 :
LG Electronics 謹此宣告此 HBS-810 產品符合
基本要求 1999/5/EC 的其他相關條款。
可於下列連結取得符合性聲明的副本:
http://www.lg.com/global/declaration
Bluetooth® 是 Bluetooth SIG, Inc. 的全球註
冊商標。
0168
FCC ID : ZNFHBS810
17
其他資訊
繁體中文
1. 無線電頻率放射
HBS-810 這款 Bluetooth 耳機是一種無線
電傳輸器及接收器。 操作中的耳機會接
收與傳輸頻率範圍在 2.4 至 2.4835 GHz 的
無線電頻率 (RF) 電磁場 (微波),藉此與
配備 Bluetooth 的行動裝置通訊。 當您的
Bluetooth 耳機與任何相容的行動電話搭配
使用時,必須遵守國家機構和國際健康機
構所制定的 RF 放射線指導方針與限制。
2. 具有潛在爆炸危險的環境
當您身在具有潛在爆炸性風險的任何區域
時,請關閉您的電子裝置。 您的電子裝
置可能會產生火花,雖然這種現象非常罕
見。 在這類區域產生火花可能造成爆炸
或火災,從而導致身體受傷,甚至死亡。
具有潛在爆炸性的區域經常、但並非總是
會有明確的標示。
18
3. 電池資訊
適當使用的充電電池使用期限較長。 全
新的電池或長時間未使用的電池,前幾
次的使用容量可能會降低。 請勿將電池
曝露在超過 +60° C (+140° F) 或低於 -10° C
(+14° F) 的極端溫度下。 為了使用最大的
電池容量,請在室溫下使用電池。 如在
低溫下使用電池,電池容量會降低。 電
池只能在 +10° C (+50° F) 至 +45° C (+113° F)
之間的溫度充電。
警告 : 本電池如果更換不正確會有爆
炸的危險。
請依製造商說明書處理用過之電池。
其他資訊
繁體中文
4. 回收 Bluetooth 耳機的電池
Bluetooth 耳機的電池必須適當處置,絕對
不能隨一般廢棄物一起處理。 取出電池
的 LG Electronics 服務夥伴將依據當地法規
處置電池。
5. 條件
- 唯有當業者提供給原始購買者的原始收據有指
定購買日期和序號,且在維修或更換產品出示
該收據時,保固才會生效。 若向業者初次購
買產品後,此資訊已移除或變更,
LG Electronics 將保留拒絕保固服務之權利。
- 此保固不包含下列因素所導致的任何產品故
障:正常損壞或撕裂,或者不當使用,包括但
不限於異常及不依慣例使用、不依照指示來使
用和維護產品。 此保固亦不涵蓋下列原因所
導致的任何產品故障:意外、修改或調整、天
災,或者液體潑灑所導致的損壞。
- 此保固不涵蓋非 LG Electronics 授權人員所執
行之不當維修安裝、修改或服務所造成的產品
故障。 損毀產品的任何封條將中止保固。
19
有限保固
繁體中文
在此有限保固條款中,LG Electronics 保證消費者在原始購買本產品時,產品之設計、材料與
製作上並無瑕疵,並在該日起一年內亦享有同等保固。 如果您的產品需要保固服務,請將產
品送回出售之業者,或聯絡您當地的 LG Electronics 聯絡中心以取得進一步資訊。
20
重要的安全資訊
繁體中文
避免損害聽力:如果您在高音量下使用耳機,可能會對聽力造成永久性的損害。
請設定安全等級的音量。 過了一段時間,您可能會習慣較大的音量並將其視為正常音量,
但此音量可能會使您的聽力受損。 如果您聽到嗡嗡聲或聽不清楚話語,請停止聆聽並檢查聽
力。 音量越大,越可能加速聽力受損的時間。 聽力專家提出了下列保護聽力的建議:
• 限制在高音量下使用耳機的時間。
• 避免調大音量來阻絕周圍噪音。
• 如果您聽不到周遭他人的談話聲,請調低音量。
請參閱手機使用者指南,瞭解更多關於如何在手機上調整音量的資訊。
安全地使用耳機:不建議您在開車時使用耳機聽音樂,且這種行為在某些地區是違法的。
開車時請小心並集中注意力。 駕駛任何類型的車輛或執行需要全神貫注的其他任何活動時,
若發現使用此裝置可能會分神或產生混亂,請停止使用。
21
NOTES
English
HBS-810 User Manual
Bluetooth® Stereo Headset
All rights reserved. LG Electronics Inc., 2016
Note: For the best performance and to prevent any damage to, or
misuse of the HBS-810, please read all of the information carefully
prior to using the HBS-810.
Any modifications or changes to this manual due to typographical
errors or inaccuracies of stated information shall only be made by
LG Electronics Inc.
Introduction
ENG
The LG TONE ULTRATM (HBS-810) is a lightweight wireless headset that uses Bluetooth® technology.
This product can be used as an audio accessory for devices supporting either the A2DP or hands-free
Bluetooth profile.
Included in the Package
Extra Ear Gels
(1 Set - Small)
HBS-810
(Medium ear gels installed)
2
User Manual
*USB Charging Cable
*Actual product design may differ from images shown in this manual.
! CAUTION
Make sure authentic LG Electronics components are used.
Using a non-authentic component may damage the product and
thus void the warranty.
Description of Parts
ENG
Headset
Charging Port
LED Indicator
CALL Button
Microphone
Earbud (L)
FF/REW Jog Button
PLAY/PAUSE/STOP Button
Earbud (R)
Power Switch
VOLUME Jog Button (+/-)
3
How to Use
ENG
Power On/Power Off
Battery Status Alert
- Slide the Power switch to the ON or OFF
position.
- Slide the VOLUME jog button to the “-”
position for 1 second to check the battery
status of the headset.
Charging
- When the charger is connected (with the
power on or off) the headset will power off.
- While charging, the LED indicator will show a
solid red light. When charged 80% or more,
the indicator will show a violet light.
- When the device is fully charged, the LED
indicator will show a solid blue light.
Low Battery
- A low battery alert will play once every 2
minutes.
- If the battery is not charged, the headset
will power off.
4
Battery
Status
Voice
Prompt
LED
Indicator
High
Medium
Low
Battery
High
Blinking
Blue
Battery
Medium
Blinking
Violet
Battery
Low
Blinking
Red
NOTE: When paired, some mobile devices may
display the headset’s battery level at the top
of the screen.
How to Use
Pairing
Before using the headset for the first time, you
must pair it with a Bluetooth-enabled device.
1) Easy Pairing
1. Slide the Power switch to the ON
position.
2. If it is your first time pairing the device
or it does not detect a previously
paired device, it will enter Pairing
mode. The LED indicator will be
solid blue.
ENG
Retractable Earbuds
- Pull the earbuds to extend them to the
desired length.
- To retract the earbuds, pull the cords out
slightly, and they will automatically retract
into place.
- If the earbuds do not retract, pull the earbuds
out completely to retract them.
3. Make sure the device you wish to
pair with is discoverable. Under the
Bluetooth menu, search for or add
new devices.
4. Select LG HBS810 from the list of
devices.
5. If asked for a Pass/Pin Code, enter
0000 (4 zeros).
6. Once the devices are paired, you
will hear “Your headset paired.” If a
connection has been made, a vibrating
alert is generated.
NOTE: The headset will automatically
power off if not paired within 3 minutes.
2) M
anual Pairing (pairing with another
phone or re-pairing)
1. With the power off, press the CALL
button and slide the Power switch to
the ON position at the same time for
2 seconds.
5
How to Use
ENG
2. When the headset enters Pairing
mode, the LED indicator will show a
solid blue light. Repeat Easy Pairing
steps 3 through 6.
Advanced Multipoint
The headset can be connected to two devices
at the same time. This will give you the freedom
to use call waiting between calls on both of
your connected phones.
Pairing with Two Devices
- First, pair the headset with the Bluetoothenabled mobile device you want to use
as your secondary device (see Pairing
instructions).
- Once paired, power off the headset.
- With the power off, press the CALL button
and slide the Power switch to the ON position
at the same time for 2 seconds to enter
Manual Pairing mode.
6
- Pair and connect the headset with your other
Bluetooth-enabled mobile device. This will be
your primary device.
- Once the primary mobile device is paired and
connected with the headset, reconnect the
headset to the initially paired mobile device.
NOTE: If a connection has been made, a
vibrating alert is generated.
NOTE: When the headset is connected to two
mobile devices at the same time (Multipoint),
the headset calling functions will work with the
primary mobile device.
NOTE: If the headset fails to connect to the
primary phone through Easy Pairing, it will
enter Pairing mode.
Calling
- Voice Dialing and Last Number Redial
features work with the primary mobile device
(or the mobile device that made the last
outgoing call).
How to Use
Auto Reconnect
- If in range of each other when the headset
is powered on, the headset and the primary
mobile device will automatically reconnect.
- The secondary mobile device will need to
be manually connected. Select LG HBS810
from the list of devices in the Bluetooth
menu and pair.
NOTE: If a connection has been made, a
vibrating alert is generated.
Out of Range
- If the paired devices are separated by a range
of 33 feet (10 meters) or more, the headset
and mobile device will disconnect, and the
headset will vibrate to alert you.
NOTE: To power off device vibration, slide the
VOLUME jog button to the “+” position and
hold for 2 seconds.
- If the headset and mobile device do not
automatically reconnect when they are back
within the required range, briefly press the
CALL button on the headset to manually
reconnect.
- While in multi-connection and streaming, the
inactive paired device will be disconnected
when out of range. The headset will alert you
once with no attempt to reconnect.
ENG
Call Waiting
- While on a call, press the CALL button for 1
second to answer an incoming call.
- To switch between two active calls, press the
CALL button for 1 second.
- To end both calls, briefly press the CALL
button.
- If both paired mobile devices are receiving an
incoming call, the headset will default to the
primary device.
7
How to Use
Calling
ENG
Answering a Call
- When receiving an incoming call, the headset
will ring and vibrate.
- Briefly slide the VOLUME jog button to the “-”
position to stop the vibration.
NOTE: The headset will not vibrate if vibration
has been deactivated.
- Briefly press the CALL button to answer the
incoming call.
Transferring a Call
- You can manually transfer the call to or from
the headset by pressing the PLAY/PAUSE/
STOP button twice on the headset (mobile
device and headset must be paired).
8
Voice Dialing
- Briefly press the CALL button to activate
Voice Command.
NOTE: If your mobile device does not support
voice dialing, this action may activate Last
Number Redial.
Last Number Redial
- Press and hold the CALL button for 1 second
to activate Last Number Redial.
The headset will beep and then call the last
number dialed.
Ending a Call
- Briefly press the CALL button.
How to Use
Rejecting a Call
- Activate Call Reject by pressing the CALL
button for 2 seconds when the mobile
device rings.
NOTE: These functions may not be available
on all mobile devices. For further information
about using these features, please consult
your mobile device’s user manual.
Microphone Mute
- Slide the VOLUME jog button to the “+”
position and the FF/REW jog button to the
REW position at the same time for 1 second
to mute/unmute the microphone during
conversation.
Caution: For your safety, do not use this
function while driving.
ENG
Call Waiting
- Answer a second call without hanging up the
first call by pressing the CALL button for 1
second. Press the CALL button for 1 second
to return to the first call.
- Briefly press the CALL button to end
both calls.
Volume Control
- Slide the VOLUME jog button to the “+” or
“-” position to adjust the speaker volume.
Caution: Listening to music for long periods of
time at high volume levels may cause hearing
damage or loss. To prevent this, the headset
will emit a warning beep when you are using
the upper 6 volume levels.
9
How to Use
Vibration Control
ENG
- To activate or deactivate the device vibration,
slide the VOLUME jog button to the “+”
position for 2 seconds. You will hear “Vibrate
on” or “Vibrate off” when it is activated or
deactivated.
- When vibration is deactivated, the headset
will not vibrate when receiving an incoming
call or when it is out of range of a paired
mobile device.
- Vibration will automatically be reactivated
when the device is powered on.
NOTE: When pairing the headset with a mobile
device, the headset will vibrate when pairing
is complete, even if the vibration function is
deactivated.
Audio Streaming
Play
- Briefly press the PLAY/PAUSE/STOP button.
10
Pause
- While playing music, briefly press the PLAY/
PAUSE/STOP button.
Stop
- While playing music, press and hold the PLAY/
PAUSE/STOP button for 1 second.
Next song
- Briefly slide the FF/REW jog button to the
FF position.
Previous song
- Briefly slide the FF/REW jog button to the
REW position.
Fast Forward
- Slide and hold the FF/REW jog button to the
FF position.
Rewind
- Slide and hold the FF/REW jog button to the
REW position.
How to Use
Equalizer
Tone & Talk
- While playing music, press the PLAY/PAUSE/
STOP button twice to switch between Bass
Boost (default), Normal, and Treble Boost.
NOTE: The size of the ear gel can affect the
amount of bass you hear.
The HBS-810 Bluetooth headset supports SMS
reading on AndroidTM-based devices.
To download the app, search for Tone & Talk in
Google PlayTM* or scan the QR code. Follow the
installation instructions.
*Google Play is a trademark of Google, Inc.
aptX®
ENG
TM
- The headset features aptX technology
that ensures audio content transmitted via
Bluetooth is seamless and crystal clear.
- aptX is automatically enabled as long as the
source device supports it.
11
How to Use
Function
ENG
Slide the FF/REW jog button to the FF position for 1 second.
Read latest SMS or MMS
Slide the FF/REW jog button to the REW position for 1 second.
Designated contact
Favorite contacts
Call logs
12
Action
Current time alert
1. Select Designated contact in the headset call settings of the app.
2. To call the Designated contact, press the CALL button twice on
your headset.
1. Select Favorite contacts in the headset call settings of the app.
2. Press the CALL button twice on your headset.
3. Use the FF/REW jog button to choose the contact.
4. To call the Favorite contact, press the CALL button twice.
1. Select Call logs in the headset call settings of the app.
2. Press the CALL button twice on your headset.
3. Use the FF/REW jog button to choose the contact.
4. To call the contact, press the CALL button twice.
Function
Operating
Charging
Headset Status
Power on
Indicator
The blue LED light flickers 4 times.
Power off
The blue LED light flickers 4 times, then powers off.
Pairing mode
Solid blue LED light.
ENG
LED Indicator
Headset/hands-free profile
The blue LED light flickers 1 time every 5 seconds.
connected
Call connected
The blue LED light flickers 1 time every 5 seconds.
Solid red LED light, which changes to violet when charged
Charging
80% or more.
Solid blue LED light.
Charging complete
13
Troubleshooting
Problem
ENG
Does not power on
Unable to
communicate with the
LG Bluetooth Headset
HBS-810
Unable to pair the
HBS-810 with the
Bluetooth device
Low sound (speaker)
14
Possible Causes
Possible Solution
Check whether the battery of the headset
Charge the battery.
is fully charged.
Check whether the mobile device you
are trying to pair supports the headset
or hands-free Bluetooth profiles.
Determine whether your mobile device
supports the headset or hands-free
Bluetooth profiles.
Check whether the battery of the
headset is low.
Charge the battery.
Check to make sure the headset is on.
Slide the Power switch to the ON position
to power on the headset.
Check to make sure the headset is placed
in Pairing mode.
With the power off, press the CALL button and slide the Power switch to the ON
position at the same time for 1 second
to manual place the headset in Manual
Pairing mode.
Check the speaker volume.
lncrease the volume level.
Specifications
Description
4.1 (Headset/Hands-Free/A2DP profiles)
Battery
Battery 3.7 V/220 mAh Lithium-ion polymer
Talk time
Up to 17 hours
Music play time
Up to 13 hours
Standby time
Up to 550 hours
Charging time
Less than 2 hours
Rated input power
DC 4.75 V ~ 5.3 V, 400 mA
Operation temperature
-10°C ~ 60°C
Dimensions / weight
147mm(W)x164mm(L)x14.9mm(H) / 41g
ENG
Item
Bluetooth version
15
Precautions
ENG
Do not disassemble, adjust, or repair the product arbitrarily.
Do not place the product near excessive heat or flammable material.
Do not arbitrarily replace the battery as it may explode.
The product may be damaged if an incompatible recharger is used.
Make sure that any infant or child does not swallow a magnet or a small component of the product.
If you have a medical device implanted, contact your doctor before use.
Do not pull the earphone cable with excessive force.
• For your safety, do not remove the battery incorporated in the product.
• Lithium-ion polymer Battery is hazardous component which can cause injury.
• Battery replacement by non-qualified professional can cause damage to your device.
• Do not replace the battery by yourself. The battery can be damaged, which can cause overheat and
injury. The battery must be replaced by authorized service provider. The battery should be recycled or
disposed separately from household wastes.
• Do not drop the product from a high place.
• Make sure there is no water, alcohol, or benzene in contact with the product.
• Do not store the product in a wet or dusty place.
• Do not place any heavy objects on the product.
• This product is not waterproof. Avoid humidity and water.
• If the product is exposed to excessive sweat, clean the product.
• Keep the earbud of the earphone always clean.
16
Declaration of Confirmation
As per Administrative Regulations on Low
Power Radio Waves Radiated Devices:
Without permission, no company, firm or user
may change the frequency, increase the power, or
alter features or functions of the original design of
type-approved low power radio-frequency devices.
The use of low power radio-frequency devices
shall not affect aircraft security or interfere with
legal communications. If found to be interfering,
the device shall cease operation immediately.
Use of the device can be resumed only after
the device has been improved to the point that
it will not cause any interference. The legal
communications mentioned above refer to radio
communications operated in compliance with
the Telecommunications Act. Low power radiofrequency devices must accept any interference
from legal communications or ISM radio wave
radiation-emitting devices.
ENG
FCC NOTICE TO USERS:
This device complies with part 15 of the FCC rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
IMPORTANT NOTE :
To comply with the FCC RF exposure
compliance requirements, no change to the
antenna or the device is permitted. Any change
to the antenna or the device could result in the
device exceeding the RF exposure requirements
and void user’s authority to operate the device.
DECLARATION OF CONFORMITY :
Hereby, LG Electronics declares that this
HBS-810 is in compliance with the essential
requirements and other relevant provisions of
Directive1999/5/EC. A copy of the Declaration
of Conformity can be found at http://www.
lg.com/global/declaration
17
Additional Information
ENG
Bluetooth® is a registered trademark of
Bluetooth SIG, Inc. worldwide.
and limits set by national authorities and
international health agencies when used with
any compatible LG Electronics mobile phone.
2. Potentially explosive atmosphere
0168
FCC ID : ZNFHBS810
1. Radio frequency exposure
18
This Bluetooth Stereo Headset HBS-810
is a radio transmitter and receiver. When in
operation, it communicates with a Bluetooth
equipped mobile device by receiving
and transmitting radio frequency (RF)
electromagnetic fields (microwaves) in the
frequency range 2.4 to 2.4835 GHz.
Your Bluetooth Headset is designed to operate
in compliance with the RF exposure guidelines
Turn off your electronic device when in any
area with a potentially explosive atmosphere.
It is rare, but your electronic device could
generate sparks. Sparks in such areas could
cause an explosion or fire resulting in bodily
injury or even death. Areas with a potentially
explosive atmosphere are often, but not
always, clearly marked.
3. Battery information
A rechargeable battery has a long service life
if treated properly. A new battery or one that
has not been used for a long period of time
could have reduced capacity the first few
times it is used. Do not expose the battery
to extreme temperatures, never above +60°
or below -10°.
For maximum battery capacity, use the
battery in room temperature. If the battery
is used in low temperatures, the battery
4. Recycling the battery in your Bluetooth
Headset
The battery in your Bluetooth Headset must
be disposed of properly and should never be
placed in municipal waste.
5. Conditions
- The warranty is valid only if the original receipt
issued to the original purchaser by the dealer,
specifying the date of purchase and serial
number, is presented with the product to be
repaired or replaced.
LG Electronics reserves the right to refuse
warranty service if this information has been
removed or changed after the original purchase
of the product from the dealer.
- If LG Electronics repairs or replaces the product,
the repaired or replaced product shall be
warranted for the remaining time of the original
warranty period or for ninety (90) days from
the date of repair, whichever is longer. Repair or
replacement may involve the use of functionally
equivalent reconditioned units. Replaced parts
or components will become the property of
LG Electronics.
- This Warranty does not cover any failure of the
product due to normal wear and tear, or due
to misuse, including but not limited to use in
other than the normal and customary manner,
in accordance with instructions for use and
maintenance of the product. Nor does this
warranty cover any failure of the product due
to accident, modification or adjustment, acts of
God or damage resulting from liquid.
- This warranty does not cover product
failures due to improper repair installations,
modifications or service performed by a non-LG
Electronics authorized person. Tampering with
any of the seals on the product will void the
warranty.
19
ENG
Additional Information
capacity will be reduced. The battery can only
be charged in temperatures between +10°
and +45°.
Limited Warranty
ENG
SUBJECT TO THE CONDITIONS OF THIS LIMITED WARRANTY, LG ELECTRONICS WARRANTS THIS
PRODUCT TO BE FREE FROM DEFECTS IN DESIGN, MATERIAL AND WORKMANSHIP AT THE TIME
OF ITS ORIGINAL PURCHASE BY A CONSUMER, AND FOR A SUBSEQUENT PERIOD OF ONE (1)
YEAR. SHOULD YOUR PRODUCT NEED WARRANTY SERVICE, PLEASE RETURN IT TO THE DEALER
FROM WHOM IT WAS PURCHASED OR CONTACT YOUR LOCAL LG ELECTRONICS CONTACT
CENTER TO GET FURTHER INFORMATION.
20
Important safety information
ENG
Avoiding hearing damage
Permanent hearing loss may occur if you use your Handsfree car kit at a high volume. Set the
volume to a safe level. You can adapt over time to a higher volume of sound that may sound normal
but can be damaging to your hearing.
If you experience ringing in your ears or muffled speech, stop listening and have your hearing
checked. The louder the volume, the less time is required before your hearing could be affected.
Hearing experts suggest that to protect your hearing:
• Limit the amount of time you use Headset at high volume.
• Avoid turning up the volume to block out noisy surroundings.
• Turn the volume down if you can’t hear people speaking near you.
Please refer to your handset user guide for more information on how to adjust listening levels on
your handset.
Using headsets safely
Use of Headset to listen to music while operating a vehicle is not recommended and is illegal in
some areas. Be careful and attentive while driving. Stop using this device if you find it disruptive or
distracting while operating any type of vehicle or performing any other activity that requires your
full attention.
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising