LG | TBNC126TSG2.ANWBLAE | LG TBNC126TSG2.ANWBLAE Owner’s Manual

e-mail http://www.lge.com
OWNER'S MANUAL
• Please read carefully and thoroughly this
manual before operating this unit.
• Contact the authorized SVC man for repair or
maintenance of this unit.
• Contact the installer for installation of this unit.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Young children should be supervised to ensure
that they do not play with the appliance.
Prior to installation, this air-conditioning
unit must be submitted for approval by the
utility service which provides electricity
(EN 61000-3 Norm).
ENGLISH
Ceiling Duct Type
Air Conditioner
Troubleshooting Tips
Care and Maintenance
Operating Instructions
Safety Precautions
Safety Precautions
Warning ................................2
Caution .................................3
Operating Instructions
Name and Function of
Remote Controller ................4
Optional Function .................5
Set the Current Time and
a day of the Week.................6
Weekly Programming ...........7
Holiday Setting .....................8
Timer Setting ........................8
Operation Mode....................9
Operation Procedure ............9
Operation Details................15
Self-diagnosis Function ......15
Safety precautions
To prevent injury to the user or other people and property damage, the
following instructions must be followed.
■ Incorrect operation due to ignoring of instruction will cause harm or
damage. The seriousness is classified by the following indications.
WARNING
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
CAUTION
This symbol indicates the possibility of injury or damage to
properties only.
Installation precautions
Care and Maintenance
Indoor unit...........................16
Outdoor unit........................16
Not used for a long time .....17
Operation Tips ....................17
Troubleshooting tips
Before You Call For
Service .............................18
WARNING
WARNING
■ Do not install, remove and reinstall the unit by yourself.
• Improper installation will cause water leakage, electrical
shock, or fire. Please consult authorized dealer or specialist
for the installation work. Please note fault caused by
improper installation is not covered by warranty.
• Unit must be installed in an easily accessible area. Any
additional cost required to hire a special equipment to
service the unit will be the responsibility of the customer.
WARNING
WARNING
Do not damage or use an
unspecified power cord.
• It will cause electrical shock or fire.
• If the supply cord is damaged, it
must be replaced by the
manufacturer or its service agent or
a similarly qualified person in order
to avoid a hazard.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
• It will cause electrical shock
or fire due to heat
generation.
Do not operate switches with wet
hands.
Plug in the power plug
properly.
• It may cause electrical shock.
• Otherwise, it will cause
electrical shock or fire due
to heat generation.
Do not insert your finger or
stick, etc. into the air inlet/air
outlet.
• Since the fan rotates at high
speed, this may cause an
injury or damage the unit.
Do not expose the skin to
cool air directly for a long
time.
• This could damage your
health.
When an abnormality (smell of burning, etc)
occurs, stop the air conditioner, and
turn off the breaker.
Repair or relocation should not be done by
the customer.
• If the unit continues to be operated in an
abnormal condition, it may cause a fire, trouble,
etc. In this case, consult your dealer.
2
• If this is done in correctly, it may cause a fire,
electric shock, injury by dropping of the unit,
water leakage, etc. Consult your dealer.
CAUTION
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young children or infirm persons
without supervision.
• Young children should be supervised to ensure that they do not play with the air
conditioner.
CAUTION
CAUTION
Do not clean the air
conditioner with water.
• Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Do not put a pet or house
plant where will be exposed to
direct air flow.
• This could injure the pet or
plant.
Do not put a stove, etc. where
is exposed to direct air flow.
Ventilate well when used
together with a stove, etc.
• An oxygen shortage may
occur.
Do not apply an insecticide
or flammable spray.
• It may cause a fire or
deformation of the cabinet.
When the unit is not going to
be used for a long time, turn
off the breaker.
• It may cause imperfect
combustion.
• It may cause an injury.
Do not operate for a long time
in high humidity, e.g. leaving
a door or window open.
Do not step onto an unstable
bench when
attaching/detaching the panel.
• In the cooling mode, if it is
operated in a room with high
humidity (80%r.h. or more) for a
long time, water condensed in
the air conditioner may drop and
may wet and spoil furniture, etc.
• It may case an injury, etc. by
falling down.
If the supply cord is damaged, it must be
replaced by a special cord or assembly availible
from the manufacturer of its service agent.
When the air filter is to be
removed, do not touch the
metal parts of the indoor unit.
• If will cause electrical shock or
fire.
• It may cause an injury.
3
When the unit is to be
cleaned, switch off, and turn
off the breaker.
• Since the fan rotates at high
speed during operation, it may
cause an injury.
Do not leave on installation
stand which is damaged.
• The unit may drop or fall down
and cause an injury.
Do not step on the outdoor
unit and do not put anything
on it.
• It may cause an injury through
dropping or falling down.
Do not use for special
purposes.
• Do not use this air conditioner
to preserve precision devices,
food, animal, plants and art
objects.
It may cause deterioration of
quality, etc.
Do not insert hands through
vanes when the air conditioner
is operating.
• It will cause an injury by the
rotating blower.
ENGLISH
• Contact the authorized Service technician for repair or maintenance of this unit.
Safety Precautions
Operating Instructions
Name and Function of Remote Controller
Remote Controller
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operating Instructions
Care and Maintenance
Timer
Operation unit
3
Signal receptor
5
8
9
10
11
12
13
03
1
Program set
05
07
09
11
13
15
17
19
21
23
2
Timer
Cancel
Program
Week
Hour
Min
6
7
4
Holiday
15
SET/CLR
RESET
14
16
Operation display
Timer Cancel Button
Displays the operation conditions.
Used to cancel the timer.
On/Off Button
Timer Set Button
Operation starts when this button is
pressed, and stops when the button is
pressed again.
Used to set the timer when the desired
time is obtained.
Set Temperature Button
Used to set a day of the week.
Week Button
Used to set the temperature when the
desired temperature is obtained.
Program Button
Used to set the weekly timer.
FAN Operation Button
Holiday Button
Used to circulate room air without cooling
or heating.
Used to set a holiday of the week.
Time Set Button
Electric Heater Button
Troubleshooting Tips
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
On Off
Set no. Time 01
FAN SPEED
Used to set the time of the day and
change the time in the weekly timer
Function.
(HEAT PUMP MODEL ONLY)
Used to set the Electric Heater.
Fan Speed Button
Set and Clear Button
Used to set desired fan speed.
Used to set and clear the weekly timer.
Operation Mode Selection
Button
Used to select the operation mode.
• Auto Operation Mode.
• Cooling Operation Mode.
• Soft Dry Operation Mode.
• Heating Operation Mode.(except cooling
model)
4
Room Temperature Checking
Button
Used to check the room temperature.
Reset Button
Used to set the current time and clear the
setting time.
Optional Function
This air-conditioner is equipped with wired remote controller basically. But if you want to be
available with wireless remote controller, you pay for it.
ENGLISH
• WIRELESS REMOTE CONTROLLER
FAN Operation Button
Remote Controller
Used to circulate room air without cooling or
heating.
Signal transmitter
Transmits the signals to the signal receptor.
Cooling Operation Button
Soft Dry Operation Button
Used to dehumidify without overcooling.
Heating Operation Button
(Heat pump model only)
1
10
4
Timer Set Button
3
9
5
2
6
7
Used to set the timer when the desired time is
obtained.
Then the wired remote controller is set up to 24
hours by an hour but the wireless remote
controller is set up to 7 hours by an hour.
Therefore, if you want to set over 7 hours, use
the wired remote controller.
8
Fan Speed Button
Used to set the desired fan speed.
On/Off Button
Operation starts when this button is pressed,
and stops when the button is pressed again.
Set Temperature Button
Used to set the temperature when the desired
temperature is obtained
Auto Operation Button
Electric Heater Button(HEAT PUMP MODEL ONLY )
Used to set the Electric Heater.
CAUTION
of handling the Remote Controller
• Aim at the signal receptor on the wired remote controller so as to operate.
• The remote control signal can be received at a distance of up to about 7m.
• Be sure that there are no obstructions between the remote controller and the signal receptor.
• Do not drop or throw the remote controller.
• Do not place the remote controller in a location exposed to direct sunlight, or near the heating unit, or any
other heat source.
• Block a strong light over the signal receptor with a curtain or etc. so as to prevent the abnormal operation.
(ex:electronic quick start, ELBA, inverter type fluorescent lamp)
5
Safety Precautions
Operating Instructions
Set the Current Time and a day of the Week
1
Press the '
' button.
Hour
Each time the button is pressed, the number is changed from 00 to 23.
You can set the number of the current hour.
AUTO SWING
OPERATION
Room Temp
Operation unit
2
Press the '
03
Care and Maintenance
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
HI
MED
LO
Hour
Program set
05
07
09
11
13
15
17
19
21
23
' button.
Min
Each time the button is pressed, the number is increased from 00 to 59.
You can set the number of the current minute.
AUTO SWING
OPERATION
SET TEMP
Room Temp
Min
Operation unit
3
Press '
Week
03
FAN SPEED
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
Program set
05
07
09
11
13
15
17
19
21
23
' button.
Each time the button is pressed, a day of the week is shifted from sunday to saturday.
You can set the day of the week.
Week
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
4
Press the '
RESET
03
FAN SPEED
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
Troubleshooting Tips
SET TEMP
Program set
05
07
09
11
13
15
17
19
21
23
' button.
If you want to reset the current time and a day of the week, click the Reset button.
AUTO SWING
OPERATION
SET TEMP
Room Temp
RESET
Operation unit
6
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
Weekly Programming
ENGLISH
1
Press the Program button.
The remote controller is displayed like a picture. Then '
Program
', '
Program set
AUTO SWING
OPERATION
' and '01' is blinked.
SET TEMP
Room Temp
2
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Operation unit
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
Week
Press the '
' button.
Select Monday.
Week
3
Change the timer setting until the desired time is set.
After you select a time, push the SET/CLR button once or one more time.
SET/CLR
Hour
Min
For Example if the air-conditioner is turned on from 6 to 8 and from 13 to 22 and turned off at other
time monday, display is as follows. (black bar indicates turn-on, white bar indicates turn-off.)
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
4
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
You can set turn on and turn off time by the day in a week as above.
7
Safety Precautions
Holiday Setting
If Tuesday is a holiday in this week, you may set a holiday.
Program
Press the Program button.
Week
Operating Instructions
Press the Week button.
Select the Tuesday.
Holiday
Press the Holiday button.
AUTO SWING
OPERATION
SET TEMP
Room Temp
Then the remote controller will be displayed '
The outside rectangular means holiday.
'.
Operation unit
03
05
07
This function is used to turn on or turn off in several hours.
Timer
to turn Timer on or off.
Change the timer setting until the desired time is set.
If you want to cancel the timer setting, press the Cancel button.
Troubleshooting Tips
Care and Maintenance
Press the Timer button
8
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
Timer Setting(Delay start/Pre-set stop)
Hour
SUB FUNCTION
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Min
Cancel
09
11
13
15
17
19
21
23
Cooling Mode
Cooling Mode
Soft Dry Mode
Soft Dry Mode
Heating Mode
Auto Mode
ENGLISH
Operation Mode
(Cooling Model)
Auto Mode
(Heat Pump Model)
Operation Procedure
1st
On/Off Button
AUTO SWING
OPERATION
SET TEMP
Room Temp
2nd
Operation unit
Operation Mode Selection Button
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
3
1
3rd
Room Temperature Setting Button
Timer
Cancel
Program
Week
Hour
Min
2
4
Holiday
SET/CLR
4th
Indoor Fan Speed Selection Button
9
RESET
Safety Precautions
Cooling Operation Mode
1
Press the On/Off Button.
2
Select Cooling Operation.
Operating Instructions
Press the Operation Mode Selection Button.
Each time the button is pressed, the operation mode is shifted in the arrow direction.
HEAT PUMP MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
03
Timer
Program set
05
07
09
11
13
15
SET TEMP
03
SUB FUNCTION
AUTO SWING
07
09
11
SET TEMP
Timer
13
15
17
Soft Dry Operation
03
SUB FUNCTION
AUTO SWING
Program set
05
07
09
11
OPERATION
SET TEMP
15
17
On Off
21Set no.
23 Time 01
19
Heating Operation
03
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Operation unit
Timer
13
FAN SPEED
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Operation unit
On Off
21Set no.
23 Time 01
19
FAN SPEED
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Operation unit
On Off
21 Set no.
23 Time 01
19
FAN SPEED
Room Temp
Program set
05
07
09
11
13
15
17
19
21
Auto Operation
COOLING MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
FAN SPEED
Room Temp
03
SUB FUNCTION
AUTO SWING
07
09
11
15
17
19
21
On Off
Set no. Time 01
23
Set the temperature
lower than the room
temperature.
03
Program set
05
07
09
AUTO SWING
OPERATION
SET TEMP
13
15
17
19
21
03
FAN SPEED
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Operation unit
On Off
Set no. Time 01
23
Program set
05
07
09
11
13
15
17
19
21
23
Auto Operation
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Operation unit
On Off
Set no. Time 01
SET TEMP
Room Temp
Timer
11
FAN SPEED
Room Temp
OPERATION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Soft Dry Operation
AUTO SWING
Timer
SUB FUNCTION
HI
MED
LO
Time
Operation unit
Timer
13
FAN SPEED
Room Temp
Cooling Operation
3
SET TEMP
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Operation unit
Timer
Care and Maintenance
17
Cooling Operation
On Off
Set no. Time 01
Troubleshooting Tips
OPERATION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Operation unit
Timer
On Off
Set no. Time 01
AUTO SWING
SUB FUNCTION
FAN SPEED
Room Temp
• The temperature can be set
within a range of 18°C ~ 30°C
by 1°C .
Program set
05
07
09
11
13
15
17
19
21
23
To raise the Temperature.
To lower the Temperature.
4
Set the fan speed.
Operation Display
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
03
SUB FUNCTION
07
09
11
OPERATION
15
17
19
21
23
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
07
09
11
15
17
19
21
23
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
13
SET TEMP
Room Temp
• Select the fan speed in three steps
- high, low, medium.
• The display shows high fan speed.
• Each time the button is pressed, the fan speed mode is shifted.
10
OPERATION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
AUTO SWING
HI
MED
LO
Time
Timer
13
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
AUTO SWING
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
23
Soft Dry Operation Mode
1
2
ENGLISH
This mode dehumidifies without overcooling.
Press the On/Off Button.
Select Soft Dry Operation.
Press the operation Mode Selection Button.
Each time the button is pressed, the operation mode is shifted in the arrow direction.
HEAT PUMP MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
03
AUTO SWING
SUB FUNCTION
07
09
11
SET TEMP
Timer
13
15
17
03
SUB FUNCTION
AUTO SWING
07
09
11
Timer
13
15
17
Soft Dry Operation
Cooling Operation
03
FAN SPEED
SUB FUNCTION
AUTO SWING
07
09
11
SET TEMP
15
17
19
On Off
21Set no.
23 Time 01
Heating Operation
03
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
07
09
11
13
15
17
Auto Operation
COOLING MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
03
SUB FUNCTION
Program set
05
07
09
11
OPERATION
15
17
19
21
23
SET TEMP
Room Temp
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
Program set
05
07
09
11
AUTO SWING
OPERATION
15
17
19
21
Soft Dry Operation
23
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Timer
13
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Timer
13
Cooling Operation
3
AUTO SWING
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
Auto Operation
During Dry Operation.
• The indoor fan speed is automatically set to the low, so the shift of the indoor fan speed
is impossible because of already being set to the best speed for Dry Operation by
Micom Control.
11
SUB FUNCTION
HI
MED
LO
Time
Operation unit
Timer
13
FAN SPEED
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Operation unit
On Off
21Set no.
23 Time 01
19
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Operation unit
On Off
21 Set no.
23 Time 01
19
FAN SPEED
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
FAN SPEED
19
21
23
Safety Precautions
Heating Operation Mode (Heat pump model only)
1
2
Press the On/Off Button.
Select Heating Operation.
Operating Instructions
Press the Operation Mode Selection Button.
Each time the button is pressed, the operation mode is shifted in the arrow direction.
Operation Display
AUTO SWING
OPERATION
SET TEMP
Operation unit
03
07
09
11
Timer
13
15
17
03
Program set
05
07
09
11
OPERATION
Timer
13
15
SET TEMP
17
Operation unit
03
FAN SPEED
03
SUB FUNCTION
AUTO SWING
07
09
11
Timer
13
15
17
SUB FUNCTION
FAN SPEED
Room Temp
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Operation unit
On Off
21Set no.
23 Time 01
19
Heating Operation
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
SET TEMP
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Operation unit
HI
MED
LO
Time
Timer
SET TEMP
Room Temp
On Off
21Set no.
23 Time 01
19
FAN SPEED
Room Temp
On Off
Set no. Time 01
OPERATION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Operation unit
SUB FUNCTION
AUTO SWING
HI
MED
LO
Soft Dry Operation
AUTO SWING
Set the temperature.
FAN SPEED
Room Temp
On Off
21 Set no.
23 Time 01
19
Cooling Operation
3
SET TEMP
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
AUTO SWING
SUB FUNCTION
FAN SPEED
Room Temp
Program set
05
07
09
11
13
15
17
19
Auto Operation
• The temperature can be set
within a range of 16°C~30°C
by 1°C.
Program set
05
07
09
11
13
15
17
19
21
23
Troubleshooting Tips
Care and Maintenance
To raise the Temperature.
To lower the Temperature.
4
Set the fan speed.
Operation Display
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
03
SUB FUNCTION
07
09
11
OPERATION
15
17
19
21
23
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
AUTO SWING
07
09
11
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Timer
13
15
17
19
21
Operation unit
On Off
Set no. Time 01
23
03
FAN SPEED
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Program set
05
OPERATION
HI
MED
LO
Time
Timer
13
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
AUTO SWING
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
• Select the fan speed in three steps
- high, low, medium.
• The display shows high fan speed
• Each time the button is pressed, the fan speed mode is shifted.
5
6
This air-conditioner is set to the hot start control in
order not to discharge the cold air during the
heating operation. This time, the remote controller
indicates ‘Preheat’.
If the outdoor temperature is too low during the
heating operation, this air-conditioner is set to the
defrosting operation and the remote controller
indicates ‘Defrost’.
12
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
On Off
Set no. Time 01
03
AUTO SWING
OPERATION
05
07
09
11
13
SET TEMP
Room Temp
Operation unit
03
15
17
19
FAN SPEED
21
23
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
SUB FUNCTION
HI
MED
LO
Time
Timer
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
21
23
Auto Operation Mode
ENGLISH
1
Press the On/Off Button.
2
To select Auto Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is shifted in the direction of the arrow.
HEAT PUMP MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
FAN SPEED
Room Temp
Operation unit
03
Timer
Program set
05
07
09
11
OPERATION
SET TEMP
13
15
17
03
SUB FUNCTION
AUTO SWING
07
09
11
Timer
13
15
17
Soft Dry Operation
Cooling Operation
FAN SPEED
03
SUB FUNCTION
AUTO SWING
07
09
11
SET TEMP
15
17
19
On Off
21Set no.
23 Time 01
Heating Operation
03
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Operation unit
Timer
13
FAN SPEED
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Operation unit
On Off
21Set no.
23 Time 01
19
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Program set
05
OPERATION
HI
MED
LO
Time
Operation unit
On Off
21 Set no.
23 Time 01
19
FAN SPEED
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
On Off
Set no. Time 01
AUTO SWING
SUB FUNCTION
HI
MED
LO
Program set
05
07
09
11
13
15
17
19
Auto Operation
COOLING MODEL
Operation Display
AUTO SWING
OPERATION
SET TEMP
FAN SPEED
Room Temp
Time
Timer
Operation unit
On Off
Set no. Time 01
03
SUB FUNCTION
AUTO SWING
07
09
11
15
17
19
21
OPERATION
SET TEMP
FAN SPEED
Room Temp
Operation unit
03
07
OPERATION
09
11
13
SET TEMP
15
03
15
17
19
21
07
09
11
17
19
21
03
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Program set
05
07
09
11
13
15
17
19
21
23
Auto Operation
To lower the Temperature.
23
Set the temperature upper or lower than the standard temperature.
The temperature can be set within a range of -2 ~ 2 by 1 level.
FAN SPEED
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
13
FAN SPEED
Time
Operation unit
On Off
Set no. Time 01
23
SET TEMP
To raise the Temperature.
Cold Cool
Program set
05
OPERATION
Room Temp
Timer
13
SUB FUNCTION
HI
MED
LO
Time
Operation unit
On Off
Set no. Time 01
11
Program set
05
Room Temp
Timer
09
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
COOLING MODEL
AUTO SWING
07
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
Program set
05
AUTO SWING
Set the temperature lower than the room themperature.
The temperature can be set within a range of 18˚C ~ 30˚C by 1˚C.
HEAT PUMP MODEL
AUTO SWING
03
SUB FUNCTION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Soft Dry Operation
Cooling Operation
3
Operation unit
On Off
Set no. Time 01
23
FAN SPEED
HI
MED
LO
Time
Timer
13
SET TEMP
Room Temp
Program set
05
OPERATION
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
15
17
19
21
Proper
Warm
Hot
To raise the Temperature.
(When you feel too cool or cold.)
23
(This indication will be shifted to the initial
Auto Mode Display state after 4 seconds.)
To lower the Temperature.
(When you feel too warm or hot.)
During Auto Operation:
❏ You can switch the indoor fan speed.
❏ The system will automatically switch from the cooling mode to the heating mode as the room
temperature and set temperature.(Heat pump model only)
13
21
23
Safety Precautions
Operating Instructions
Care and Maintenance
Troubleshooting Tips
FAN Operation
1
Press the On/Off Button.
2
Press FAN Operation Button.
3
Each time Indoor Fan Speed button is pressed, the fan speed mode is shifted in the
arrow direction.
AUTO SWING
OPERATION
SET TEMP
Room Temp
Operation unit
03
SUB FUNCTION
Program set
05
07
09
11
AUTO SWING
OPERATION
15
17
19
• Fan speed is high.
21
23
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
Program set
05
07
09
11
AUTO SWING
OPERATION
15
17
19
• Fan speed is low.
21
23
Operation unit
On Off
Set no. Time 01
03
FAN SPEED
SUB FUNCTION
HI
MED
LO
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
Time
Timer
13
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Timer
13
SET TEMP
Room Temp
AUTO Heater Preheat
JET Defrost Humidify
Filter Out door
ZONE
1 2 3 4
HI
MED
LO
Time
Timer
On Off
Set no. Time 01
FAN SPEED
Program set
05
07
09
11
13
15
17
19
21
23
• Fan speed is medium.
Electric Heater (HEAT PUMP MODEL ONLY)
• On heating mode, Electric Heater is on automatically and pressing Electric Heater Button,
Heater is off.
• Mal-functional on Cooling and fan operation mode.
• If Electric Heater is off during Electric Heater running, indoor fan still runs to purge hot air
about 1 minute more.
• This is designed to Cool Electric Heater.
• If mode is changed to deice mode during heating mode Electric Heater is off automatically,
and run automatically when Heating mode is on again.
• On heating mode, Heater is off in case room temperature is higher than set temperature by
1°C, and run again in case room temperature is lower than set temperature by 2°C.
14
Operation Details
When the room temperature is higher than the set temperature, it operates in cooling mode at
the set temperature, the set fan speed, and then it will be in automatically turn off when the
room temperature reaches the set temperature +0.5°C.
ROOM TEMP.
More 3 minutes
OPERATION START
SET TEMP. +0.5°C)
OPERATION STOP
SET TEMP. -0.5°C)
INDOOR FAN
OUTDOOR FAN/COMP
: SETTING FAN SPEED
: LOW COOL OPERATION
: COMP ON
: COMP OFF
Helpful information
Airflow speed and cooling capacity.
The cooling capacity indicated in the specification
is the value when the fan speed is set to high, and
the capacity will be lower at low or medium fan
speed.
High fan speed is recommended when you wish to
cool the room quickly.
h
Hig
d
ee
Sp
Self-Diagnosis Function
'CHECK' will flash in the remote controller display when a problem occurs. Then please contact
your dealer.
15
ENGLISH
• Cooling Operation Mode
Safety Precautions
Caution: Before performing any maintenance, turn off the main power to the system.
Indoor Unit
Grille, Case, and Remote Control
❏ Turn the system off before cleaning. To
clean, wipe with a soft, dry cloth. Do not
use bleach or abrasives.
Note:
Supply power must be disconnected
before cleaning the indoor unit.
Troubleshooting Tips
❏ Never use any of the followings:
• Water hotter than 40°C
Could cause deformation and/or
discoloration.
• Volatile substances
Could damage the surfaces of the
air conditioner.
SI
Air outlet vent
Be
Air filters
Air Filter
The air filters behind Indoor unit
(the suction side) should be checked and cleaned
once every 2 weeks or more often if necessary.
Care and Maintenance
Operating Instructions
Care and maintenance
1
N NER
n zene
SCO
U RIN G
C LB
A R GER
Clean the filter with a vacuum or warm,
soapy water.
• If very dirty, wash with a solution of
detergent in lukewarm water.
• If hot water (50°C or more) is used,
filter may be deformed.
2 After washing with water, dry well in the
shade.
3 Re-install the air filter.
Outdoor Unit
The heat exchanger coils and panel vents of the
outdoor unit should be checked regularly. If
clogged with dirt or soot, the heat exchanger
and panel vents may be professionally steam
cleaned.
(Side)
(Side)
Air intake
vents
(Rear)
Air intake
vents
Air outlet
Piping vents
Air outlet
vents
16
Note:
Dirty or clogged coils will reduce the
operating efficiency of the system and cause
higher operating costs.
(Rear)
Air outlet vents
Piping
(Rear)
(Side)
Air intake
vents
Piping
When the air conditioner is to
be used again.
When it is not going to be used for
a long time.
Operate the air conditioner on Air circulation
mode (Refer to page 14) for 2 to 3 hours.
■ Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
• This will dry out the internal parts.
Turn off the circuit breaker.
Helpful information
CAUTION
CAUTION
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
The air filters and your electiric bill.
If the air filters become clogged with dust, the
cooling capacity will drop, and 6% of the electricity
used to operate the air conditioner will be wasted.
Operation Tips
Do not overcool the room.
This is not good for the health
and wastes electricity.
Clean the air filter regularly.
Blockages in the air filter
reduce the airflow and lower
cooling and dehumidifying
effects. Clean at least once
every two weeks.
Keep blinds or curtains
closed.
Do not let direct sunshine
enter the room when the air
conditioner is in operation.
Ventilate the room
occasionally.
Since windows are kept
closed, it is a good idea to
open them and ventilate the
room now and then.
17
Make sure that the doors
and windows are shut tight.
Avoid opening doors and
windows as much as possible
to keep the cool air in the
room.
ENGLISH
When the air conditioner is not going to be used for a long time.
Safety Precautions
Before you call for service...
?
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the malfunction persist,
please contact your dealer.
Troubleshooting Tips
Care and Maintenance
Operating Instructions
The air conditioner
does not operate.
The room has a
peculiar odor.
It seems that
condensation is
leaking from the air
conditioner.
Air conditioner does
not operate for about
3 minutes when
restart.
• Check that this is not
a damp smell exuded
by the walls, carpet,
furniture or cloth
items in the room.
• Condensation occurs
when the airflow from
the air conditioner
cools the warm room
air.
• This is the protector
of the mechanism.
• Wait about three
minutes and
operation will begin.
Does not cool or heat
effectively.
The air conditioner
operation is noisy.
Crack sound is
heard.
• Is the air filter dirty?
See air filter cleaning
instructions.
• The room may have
been very hot when
the room air
conditioner was first
turned on. Allow time
for it to cool down.
• Has the setting
temperature been set
incorrectly?
• Are the indoor unit's
air inlet or outlet
vents obstructed?
• For a noise that
sounds like water
flowing.
-This is the sound of
freon flowing inside
the air conditioner
unit.
• For a noise that
sounds like the
compressed air
releasing into
atmosphere.
-This is the sound of
the dehumidifying
water being
processed inside the
air conditioning unit.
• Have you made a
mistake in timer
operation?
• Has the fuse blown
or has the circuit
breaker been
tripped?
• This sound is
generated by the
expansion/contractio
n of the inlet grille,
etc. due to changes
of temperature.
Remote control
display is faint, or no
display at all.
• Has the circuit
breaker been
tripped?
NOTE
WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT.
The indoor side is not water resistant and should not be exposed to
excess water.
18
P/No.: 3828A90194A
Download PDF