LG | HLT35W | LG HLT35W Owner’s Manual

OWNER’S MANUAL
32 TV Matching
DVD SOUND BAR
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
HLT35W (HLT35W, SHT35-D)
P/NO : MFL66306831
HLT35W-F2_BPHLLL_ENG_6831.indd 1
2010-10-07 �� 3:37:28
2
1
Safety Information
Safety Information
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK) NO USERSERVICEABLE PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the cord
exits the appliance. To disconnect power from the
mains, pull out the mains cord plug. When installing
the product, ensure that the plug is easily accessible.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
HLT35W-F2_BPHLLL_ENG_6831.indd 2
2010-10-07 �� 3:37:29
3
Safety Information
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
This device is equipped with a portable battery or
accumulator.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer's
instructions.
Safe way to remove the battery or the battery
from the equipment:
1
Safety Information
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from overheating.
The openings should be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer's
instruction have been adhered to.
Remove the old battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put in the appropriate
container at designated collection points. Do not
dispose of batteries or battery together with other
waste. It is recommended that you use local, free
reimbursement system batteries and accumulators.
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
Copyrights
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent
copyrighted material without permission. This
product features the copy protection function
developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and
playing the pictures of these discs picture noise
will appear. This product incorporates copyright
protection technology that is protected by U.S.
patents and other intellectual property rights. Use
of this copyright protection technology must be
authorized by Macrovision, and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION
’ OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
HLT35W-F2_BPHLLL_ENG_6831.indd 3
2010-10-07 �� 3:37:29
4
Contents
Contents
20
AUX In Connection
20
AUDIO (PORT. IN) In
20
Listening to music from your
Connection
1
portable player or external
Safety Information
2
2
CAUTION
Preparation
3
4
5
6
21
USB Connection
22
OPTICAL In connection
22
Antenna Connection
23
Adjust the setup settings
6
Unique Features
23
OSD Initial language settings
6
Accessories
23
To display and exit the Setup
7
Introduction
7
Playable Discs
7
About the  Symbol Display
7
Symbol Used in this Manual
7
Regional Codes
8
Playable file Requirement
9
Remote control
11
Front panel
12
Rear panel
Installation
13
device
Mounting the main unit on a
wall
7
15
Setting up
17
Connections to Your TV
menu
24
Language
24
Display
25
Audio
26
Lock (Parental Control)
27
Others
Operation
28
Using the Home Menu
28
Basic Operations
29
Other Operations
29
Displaying Disc Information onscreen
30
To display the DVD Menu
30
To display the DVD title
30
1.5 times speed playback
17
HDMI Out Connection
30
Screen Saver
18
Video Connection
30
Starting play from selected
19
Resolution Setting
Resume playback
Marked Playback
time
19
Video Output Resolution
30
20
Optional Equipment Connection
31
HLT35W-F2_BPHLLL_ENG_6831.indd 4
2010-10-07 �� 3:37:29
Contents
5
Appendix
31
Changing subtitle code page
32
Viewing a PHOTO file
32
Options while viewing a photo
39
Language Codes
33
Sleep Timer Setting
40
Area Codes
33
Turn off the sound temporarily
33
Last Scene Memory
41
Trademarks and Licenses
33
System Select - Optional
42
Specifications
33
Adjust the speaker level
1
2
settings
33
34
VOCAL FADER
Radio Operations
34
Listening to the radio
34
Presetting the Radio Stations
34
Deleting all the saved stations
34
Deleting a saved station
34
Improving poor FM reception
35
35
4
Sound adjustment
Setting the surround mode
36
Advanced Operations
36
Recording to USB
Maintenance
37
Notes on Discs
37
Handling the Unit
Troubleshooting
38
3
5
6
7
Troubleshooting
HLT35W-F2_BPHLLL_ENG_6831.indd 5
2010-10-07 �� 3:37:29
6
Preparation
2
Preparation
2
Unique Features
Preparation
Portable In
Listens to music from your portable device.
(MP3, Notebook, etc)
Remote control (1)
Batteries (2)
FM antenna (1)
Wall bracket (1)
WALL BRACKET
INSTALL GUIDE (1)
Screw (4)
USB Direct Recording
Records music from CD to your USB device.
Full HD up-scaling
Views Full HD picture quality with simple setup.
Home Theater Speaker ez
Setup
Listens to sound from TV, DVD and Digital
device with vivid 2.1 or 2.0 ch mode.
Accessories
Unit brackets (2)
Please check and identify the supplied
accessories.
Video cable (1)
HDMI cable (1)
HLT35W-F2_BPHLLL_ENG_6831.indd 6
2010-10-07 �� 3:37:30
Preparation
Introduction
Playable Discs
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and finalized only
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only
DVD+R: Video mode only
Supports the double layer disc
also
DVD+RW (8 cm / 12 cm disc)
Video mode and finalized only
Audio CD: Music CDs or CD-R/CDRW in music CD format that can
be purchased.
About the  Symbol Display
“  ” may appear on your TV display during
operation and indicates that the function
explained in this owner’s manual is not
available on that disc.
HLT35W-F2_BPHLLL_ENG_6831.indd 7
Symbol Used in this Manual
All discs and file listed below ALL
MP3 files MP3
DVD and finalized DVD±R/RW
DVD
WMA files WMA
DivX files DivX
Audio CDs ACD
JPG files
JPG
NOTE
2
Preparation
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CDRW/CD-R cannot be played on this unit due to
the recording quality or physical condition of
the disc, or the characteristics of the recording
device and authoring software.
7
Indicates special notes and operating features.
TIP
Indicates tip and hints for making the task
easier.
CAUTION
Indicates cautions for preventing possible
damages from abuse.
Regional Codes
This unit has a regional code printed on the
rear of the unit. This unit can play only DVD
discs labeled same as the rear of the unit or
“ALL”.
• Most DVD discs have a globe with one or
more numbers in it clearly visible on the
cover. This number must match your unit’s
regional code or the disc cannot play.
• If you try to play a DVD with a different
regional code from your unit, the message
“Check Regional Code” appears on the TV
screen.
2010-10-07 �� 3:37:30
8
Preparation
Playable file
Requirement
MP3/ WMA music file requirement
2
MP3/ WMA file compatibility with this unit is
limited as follows :
Preparation
• Sampling frequency : within 32 to 48 kHz
(MP3), within 32 to 48 kHz (WMA)
• Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
• Support Version : v2, v7, v8, v9
• Maximum files : Under 999
• File extensions : “.mp3”/ “.wma”
• CD-ROM file format : ISO9660/ JOLIET
• We recommend that you use Easy-CD
Creator, which creates an ISO 9660 file
system.
DivX file requirement
DivX file compatibility with this unit is limited
as follows :
• Available resolution: within 720x576 (W x H)
pixels.
• The file name of the DivX subtitle should be
entered within 45 characters.
• If there is impossible code to express in the
DivX file, it may be displayed as " _ " mark
on the display.
• Frame rate : less than 30 fps.
• If the video and audio structure of recorded
files is not interleaved, either video or audio
is outputted.
• Playable DivX file : ".avi", ".mpg", ".mpeg",
".divx"
• Playable Subtitle format : SubRip (*.srt/
*.txt), SAMI (*.smi), SubStation Alpha (*.ssa/
*.txt), MicroDVD (*.sub/ *.txt), SubViewer 2.0
(*.sub/ *.txt), Vobsub (*.sub)
• Playable Codec format : "DIVX3.xx", "DIVX4.
xx", "DIVX5.xx", "MP4V3", "3IVX".
Photo file requirement
• Playable Audio format : "AC3", "PCM", "MP3",
"WMA".
Photo file compatibility with this unit is limited
as follows :
• Sampling frequency : within 32 to 48 kHz
(MP3), within 32 to 48 kHz (WMA)
• Max pixel in width : 2760 x 2048 pixel
• Bit rate : within 32 to 320 kbps (MP3), 40 to
192 kbps (WMA)
• Maximum files : Under 999
• Some discs may not operate due to a
different recording format or the condition
of disc.
• File extensions: “.jpg”
• CD-ROM file format : ISO9660/ JOLIET
HLT35W-F2_BPHLLL_ENG_6831.indd 8
• For Discs formatted in Live file system, you
can not it on this unit.
• If the name of movie file is different from
that of the subtitle file, during playback of a
DivX file, subtitle may not be display.
• If you play a DivX file different from
DivXspec, it may not operate normally.
2010-10-07 �� 3:37:30
Preparation
Remote control
t RADIO&INPUT: Changes input sources.
• • • • • • • • • • b • • • • • • • • • 0 to 9 numerical buttons : Selects numbered
options in a menu.
Remote control
OPEN /
CLOSE
a
RADIO &
INPUT
REPEAT
SKIP
c
./> SKIP : Goes to next or previous
chapter/ track/ file.
SCAN
m/M SCAN : Searches backward or forward.
SKIP
x (STOP) : Stops playback or recording.
MONO/STEREO
SPEAKER
LEVEL
d
B (PLAY), MONO/STEREO : Starts playback.
Selects Mono/ Stereo.
OPTICAL
VOL
SOUND
EFFECT
X (PAUSE/STEP) : Pauses playback.
• • • • • • • • • • d • • • • • • • • • MUTE
SPEAKER LEVEL: Sets the sound level of
desired speaker.
HOME
PRESET
TUNING
TUNING
ENTER
RETURN
TITLE
MIC VOL
MARKER
DISC MENU
ECHO VOL
SLEEP
REC
VOCAL FADER
AV / INPUT
SOUND EFFECT: Selects a sound effect mode.
VOL -/+ (Volume) : Adjusts speaker volume.
PRESET
g
2
Preparation
• • • • • • • • • • c • • • • • • • • • CLEAR
f
CLEAR : Removes a number when setting the
password.
REPEAT : Selects a play mode. (Repeat/
Repeat all/ Random)
b
e
9
VOL
PR/CH
VOL
PR/CH
OPTICAL: Changes input source to optical
directly.
MUTE : Mutes the sound.
Put the batteries into the remote control
Make sure for the + (plus) and – (minus) on
the batteries to be matched on the remote
control.
• • • • • • • • • • a • • • • • • • • • 1 (POWER) : Switches the unit ON or OFF.
Z OPEN/CLOSE : Opens and closes the disc
Drawer.
HLT35W-F2_BPHLLL_ENG_6831.indd 9
2010-10-07 �� 3:37:31
10
Preparation
TUNING -/+ : Tunes in the desired radio station.
Remote control
OPEN /
CLOSE
a
RADIO &
INPUT
O RETURN : Moves backwards in the menu
or exits the setup menu.
TITLE : If the current DVD title has a menu, the
title menu appears on the screen. Otherwise,
the disc menu may not appear.
b
2
CLEAR
REPEAT
Preparation
SKIP
c
SCAN
DISC MENU : Accesses the menu on a DVD
disc.
• • • • • • • • • • f • • • • • • • • • SKIP
MONO/STEREO
ECHO VOL. -/+ : Adjusts echo volume.
SPEAKER
LEVEL
d
OPTICAL
MIC VOL. -/+ : Adjusts microphone volume.
VOL
SOUND
EFFECT
MARKER : Marks play list.
MUTE
SLEEP : Sets the System to turn off
automatically at a specified time.
HOME
z REC : USB Direct Recording.
PRESET
TUNING
e
ENTER
TUNING
PRESET
RETURN
TITLE
MIC VOL
f
MARKER
DISC MENU
ECHO VOL
SLEEP
REC
VOCAL FADER
g
 ENTER : Acknowledges menu selection.
Presetting the radio stations.
AV / INPUT
VOL
PR/CH
VOL
PR/CH
• • • • • • • • • • e • • • • • • • • • VOCAL FADER : You can enjoy the function as
karaoke, by reducing singer vocal of music in
the various source.
• • • • • • • • • • g • • • • • • • • • TV Control buttons : Controls the TV. (LG TV
only)
Controlling the TV
You can control the sound level, input
source, and power switching of LG TVs as
well. Hold POWER (TV) and press PR/CH
(U/u) button repeatedly until the TV turns
on or off.
HOME: Displays the [Home] menu.
INFO/DISPLAY : Accesses On-Screen
Display.
U/u/I/i (up/ down/ left/ right): Used to
navigate on-screen displays.
PRESET (+/-) : Selects programme of Radio.
HLT35W-F2_BPHLLL_ENG_6831.indd 10
2010-10-07 �� 3:37:31
Preparation
11
Front panel
A BC
D
E
2
Preparation
A Microphone
E Disc slot
B PORT. IN
C USB Port
D Touch buttons
• 1 STANDBY/ON
•i|| (PLAY / PAUSE)
FUNC. ( )
Press and hold down this button for
about 3 seconds, then press repeatedly
to select other function.
•s (STOP)
• - VOL +
Adjusts speaker volume.
•
Ejects or inserts disc.
Touch the blue or red LED button to operate
the unit.
CAUTION
Precautions in using the touch buttons
• Do not press the touch buttons hard to make it
work.
-If you apply too much strength, it can damage
the sensor of the touch buttons.
• Touch the button that you want to work in order
to operate the function correctly.
• Be careful not to have any conductive material
such as metallic object on the touch buttons. It
can cause malfunctions.
• Be careful not to have any conductive material
such as metallic object on the touch buttons. It
can cause malfunctions.
HLT35W-F2_BPHLLL_ENG_6831.indd 11
2010-10-07 �� 3:37:31
12
Preparation
Rear panel
E
2
Preparation
A
B
C
D
A Antenna Connector
D HDMI OUT
B AUX IN (L/R)
E OPTICAL IN
C VIDEO OUT
HLT35W-F2_BPHLLL_ENG_6831.indd 12
2010-10-07 �� 3:37:31
Installation
13
3
Installation
Mounting the main unit on a
wall
You can mount the main unit on a wall.
Prepare screws and brackets supplied.
2. When you mount it on a wall (concrete), use
the wall plugs (Not supplied). You should
drill some holes. A guide sheet (WALL
BRACKET INSTALL GUIDE) is supplied to drill.
Use the sheet to check the point to drill.
3
Step 2
Preperation
Installation
Unit
Wall bracket
Screws
Unit bracket
WALL BRACKET
INSTALL GUIDE
1. Match the TV BOTTOM LINE of WALL
BRACKET INSTALL GUIDE with the bottom
of TV and attach to the position.
Step 1
NOTE
Screws and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti (HUD1 6 x 30) for the mounting. Please purchase it.
TV
HLT35W-F2_BPHLLL_ENG_6831.indd 13
2010-10-07 �� 3:37:32
14
Installation
3. Remove the WALL BRACKET INSTALL GUIDE.
4. Fix it with screws (not supplied) as shown in
the illustration below.
6. Remove the stand from the unit.
Step 6
Step 4
3
Installation
7. Hang the main unit onto the brackets, as
shown below.
5. Attach the unit bracket to the unit
with screws (supplied) as shown in the
illustration below.
Step 7
Step 5
NOTE
Detach the unit from the bracket as shown below.
CAUTION
• Do not hang onto the installed unit and avoid
any impact to the unit.
• Secure the unit firmly to the wall so that it does
not fall off. If the unit falls off, it may result in an
injury or damage to the product.
• When the unit is installed on a wall, please make
sure that a child does not pull any of connecting
cables, as it may cause it to fall.
HLT35W-F2_BPHLLL_ENG_6831.indd 14
2010-10-07 �� 3:37:32
Installation
Setting up
Wireless connection
LED indicator of wireless subwoofer
LED Color
Operation
Blue
The wireless subwoofer is
receiving the signal of the
unit.
The wireless subwoofer is
trying to connect.
Red
The Wireless subwoofer is in
standby mode.
Off (No
display)
The Wireless subwoofer is
turned off.
Initial setting an ID of wireless
subwoofer
Setting an ID of wireless subwoofer
When the unit is manufactured, the ID is
already set. If an interference occurs or you
use a new wireless subwoofer, an ID should be
set again.
1. Press HOME (
).
2. Use I/i to select the [Setup] and
press ENTER ( ). The [Setup] menu appears.
3. Use U/u to select [AUDIO] option then
press i to move to the second level.
4. Use U/u to select the [Connecting
Speakers] option then press ENTER ( ) to
move to the third level.
The [Wireless Speaker Connection Guide]
appears.
5. Press PAIRING button on the subwoofer.
- If you see the blue LED indicator light,
pairing was successful.
3
Installation
Blue (blink)
15
6. Use U/u to select the [2.1 Speaker Setup]
and press ENTER ( ) for wireless speaker
connection test.
1. Connect the power cord of the Wireless
subwoofer to the outlet.
2. Turn on the main unit : The main unit and
wireless subwoofer will be automatically
connected.
HLT35W-F2_BPHLLL_ENG_6831.indd 15
2010-10-07 �� 3:37:32
16
Installation
NOTE
• If you operate main unit then wireless subwoofer
(rear speakers) sound within a few seconds in
standby mode.
• Set the distance between this unit and
subwoofer Receiver within 10 m (32 ft.).
• Optimum performance can be implemented
only when the unit and the Wireless subwoofer
within distance of 2 m (6 ft.) to 10 m (32 ft.) is
used since communication failure may occur if
longer distance is used.
3
• It takes a few seconds (and may take longer)
for the Wireless Transmitter and subwoofer to
communicate with each other.
Installation
HLT35W-F2_BPHLLL_ENG_6831.indd 16
2010-10-07 �� 3:37:32
Installation
Connections to Your
TV
Make one of the following connections,
depending on the capabilities of your existing
equipment.
NOTE
HDMI Out Connection
If you have a HDMI TV or monitor, you can
connect it to this unit using a HDMI cable.
Connect the HDMI OUT jack on the unit to
the HDMI IN jack on a HDMI compatible TV or
monitor.
Set the TV’s source to HDMI (refer to TV’s
Owner’s manual).
HDMI Connection
• Depending on your TV and other equipment
you wish to connect, there are various ways
you could connect the unit. Use only one of the
connections described in this manual.
3
Installation
• Please refer to the manuals of your TV, Stereo
System or other devices as necessary to make
the best connections.
• Make sure the unit is connected directly to
the TV. Tune the TV to the correct video input
channel.
17
Unit
• Do not connect your unit via your VCR. The
image could be distorted by the copy protection
system.
TV
TIP
• You can fully enjoy digital audio and video
signals together with this HDMI connection.
• When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 19.)
HLT35W-F2_BPHLLL_ENG_6831.indd 17
2010-10-07 �� 3:37:33
18
Installation
NOTE
• If a connected HDMI device does not accept
the audio output of the unit, the HDMI device
’s audio sound may be distorted or may not
output.
• When you connect a HDMI or DVI compatible
device make sure of the following:
- Try switching off the HDMI/DVI device and this
unit. Next, switch on the HDMI/DVI device and
leave it for around 30 seconds, then switch on
this unit.
Video Connection
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
You can hear the sound through the
system’s speakers.
Video Connection
- The connected device’s video input is set
correctly for this unit.
3
Installation
- The connected device is compatible with
720x576i (or 480i), 720x576p (or 480p),
1280x720p,1920x1080i or 1920x1080p video
input.
• Not all HDCP-compatible HDMI or DVI devices
will work with this unit.
- The picture will not be displayed properly with
non-HDCP device.
- This unit does not playback and TV screen is
changed to black or green screen or the snow
noise may occur on the screen.
Unit
TV
• If there is noise or lines on the screen, please
check the HDMI cable and use a higher version
cable than 1.2A HDMI cable.
CAUTION
• Changing the resolution when the connection
has already been established may result in
malfunctions. To solve the problem, turn off the
unit and then turn it on again.
• When the HDMI connection with HDCP is
not verified, TV screen is changed to black or
green screen or the snow noise may occur on
the screen. In this case, check the the HDMI
connection, or disconnect the HDMI cable.
HLT35W-F2_BPHLLL_ENG_6831.indd 18
2010-10-07 �� 3:37:33
Installation
Resolution Setting
The player provides several output resolutions
for HDMI OUT jacks. You can change the
resolution using [Setup] menu.
1. Press
19
Video Output
Resolution
HOME.
2. Use I/i to select the [Setup] and press 
ENTER. The [Setup] menu appears.
[HDMI OUT]: 1080p, 1080i, 720p and 576p (or
480p) and 576i (or 480i)
[VIDEO OUT]: 576i (or 480i)
3
4. Use U/u to select the [Resolution] option
then press i to move to the third level.
Installation
3. Use U/u to select [Display] option then
press i to move to the second level.
5. Use U/u to select the desired resolution
then press  ENTER to confirm your
selection.
NOTE
If your TV does not accept the resolution you have
set on the player, you can set resolution to 576p (or
480p) as follows:
Press x (STOP) for more than 5 seconds.
HLT35W-F2_BPHLLL_ENG_6831.indd 19
2010-10-07 �� 3:37:33
20
Installation
Optional Equipment
Connection
AUDIO (PORT. IN) In
Connection
Connect an output of portable device (MP3
or PMP etc) to the AUDIO (PORT. IN) input
connector.
PORT.IN Connection
AUX In Connection
Connect an Output of auxiliary device to the
AUX (L/R) INPUT Connector.
AUX IN Connection
3
Installation
MP3 player, etc...
Listening to music from your
portable player or external
device
Unit
The unit can be used to play the music from
many types of portable player or external
devices.
To the audio output jacks
of your component
(TV, VCR, etc.)
Red
White
1. Connect the portable player to the
PORT.IN(PORTABLE IN) connector of the
unit.
Or
Connect the external device to the AUX
connector of the unit.
2. Turn the power on by pressing 1 (POWER).
NOTE
If your TV has only one output for audio (mono),
connect it to the left (white) audio jack on the unit.
HLT35W-F2_BPHLLL_ENG_6831.indd 20
3. Select the PORTABLE or AUX (L/R) INPUT
function by pressing t RADIO&INPUT.
4. Turn on the portable player or external
device and start playing it.
2010-10-07 �� 3:37:33
Installation
USB Connection
Compatible USB Devices
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the
unit.
• USB Flash Drive :Devices that support
USB2.0 or USB1.1.
USB Connection
21
• MP3 Player : Flash type MP3 player.
• The USB function of this unit does not
support some USB devices.
USB device requirement
• Devices which require additional program
installation connected to a computer, are
not supported.
• Do not extract the USB device while in
operation.
• To prevent data loss, back up all data.
• If you use a USB extension cable or USB
hub, the USB device is not recognized.
3
Installation
• For a large capacity USB, it may take longer
than a few minutes to be searched.
• Using NTFS file system is not supported.
(Only FAT(16/32) file system is supported.)
Removing the USB Device from the unit
1. Choose a different function mode or
press STOP (x) twice in a row.
2. Remove the USB device from the unit.
HLT35W-F2_BPHLLL_ENG_6831.indd 21
• This unit is not supported when the total
number of files is 1 000 or more.
• External HDD, Card readers, Locked devices, or hard type USB devices are not supported.
• USB port of the unit cannot be connected
to PC. The unit can not be used as a storage
device.
2010-10-07 �� 3:37:33
22
Installation
OPTICAL In connection
Antenna Connection
Connect an optical output of Unit (or Digital
Device etc) to the OPTICAL IN connector.
OPTICAL IN Connection
Connect the supplied FM antenna for listening
to the radio.
Connect the FM Wire antenna to the FM
antenna connector.
Antenna Connection
3
Installation
To the digital
optical output jack
of your component
Home theater speaker ez setup
Listen to sound from TV, DVD and Digital
Device with 2.1 or 2ch mode. Even in power off
mode, if you press OPTICAL, then power is on
and automatically changed to AUX OPT mode.
1. Connect the unit’s OPTICAL IN jack to jack
on optical out of your TV (or Digital Device
etc.).
2. Select the AUX OPT by using the OPTICAL.
To select the AUX OPT directly
NOTE
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it as
horizontal as possible.
3. Listen to sound with 2.1 or 2ch speaker.
4. To escape from AUX OPT by using the
OPTICAL.
Function is retuned to previous one.
HLT35W-F2_BPHLLL_ENG_6831.indd 22
2010-10-07 �� 3:37:34
Installation
Adjust the setup
settings
By using the Setup menu, you can make
various adjustments to items such as picture
and sound.
You can also set a language for the subtitles
and the Setup menu, among other things. For
details on each Setup menu item, see pages 23
to 27.
During the first use of this unit, the initial
language setup menu appears on your TV
screen. You must complete initial language
selection before using the unit. English will be
selected as the initial language.
1. Press 1 (POWER) to turn the unit on. The
language setup menu will appear on the
screen.
2. Use U u I i to select a language then
press  ENTER.
The confirm menu will appear.
To display and exit the Setup
menu
1. Press HOME.
Displays the [Home Menu].
2. Select a [Setup] by using I i.
3. Press  ENTER.
Displays the [Setup]
4. Press HOME or O RETURN to exit in
the [Setup] Menu.
About help menu for Setup
Menu
Buttons
Operation
Uu
Moving to another
menu.
b
Move
I
Moving to previous
level.
B
Move
i
O
Close
O
RETURN
To exit the [Setup]
menu or [ 2.1
Speaker Setup].

Select
 ENTER
To confirm menu.
vV
Move
3
Installation
OSD Initial language settings
23
Moving to next level
or selecting menu.
3. Use I i to select the [Enter] then press 
ENTER to finish the language setup.
HLT35W-F2_BPHLLL_ENG_6831.indd 23
2010-10-07 �� 3:37:34
24
Installation
Language
Menu Language
Select a language for the Setup menu and
then on screen display.
Disc Audio / Disc Subtitle / Disc
Menu
Select the language you prefer for the audio
track (disc audio), subtitles, and the disc menu.
3
[Original]
Refers to the original language in which the
disc was recorded.
Installation
[Other]
To select another language, press numeric
buttons and then  ENTER to enter the
corresponding 4-digit number according
to the language code list on the page 39. If
you enter the wrong language code, press
CLEAR.
[Off (for Disc Subtitle)]
Turn off Subtitle.
Display
TV Aspect
Select which screen aspect to use based on
the shape of your TV screen.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
HLT35W-F2_BPHLLL_ENG_6831.indd 24
Display Mode
The Display Mode setting works only when the
TV Aspect mode is set to 4:3.
[Letterbox]
Displays a wide picture with bands on the
upper and lower portions of the screen.
[Panscan]
Automatically displays the wide picture
on the entire screen and cuts off the
portions that do not fit. (If the disc/file is not
compatible with Pan Scan, the picture is
displayed at Letterbox ratio.)
Resolution
Sets the output resolution of the HDMI video
signal. Refer to page 19 or details about the
resolution setting.
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best
suited to the connected TV.
[1080p]
Outputs 1080 lines of progressive video.
[1080i]
Outputs 1080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[576p (or 480p)]
Outputs 576 (or 480) lines of progressive
video.
[576i (or 480i)]
Outputs 576 (or 480) lines of interlaced
video.
2010-10-07 �� 3:37:34
Installation
Audio
2.1 Speaker Setup
Make the following settings for the built-in 2.1
channel surround decoder.
1. Select [2.1 Speaker Setup] on the [Audio]
menu.
2. Press  ENTER.
The [2.1 SPEAKER] appears.
[Size]
Since the speaker settings are fixed, you
cannot change the settings.
[Volume]
Press I i to adjust the output level of the
selected speaker.
Front L/R : 0 ~ -5
SubWoofer : 5 ~ -5
4. Adjust options using U u I i buttons.
Make the sound clear when the volume is
turned down (Dolby Digital only). Set to [On]
for this effect.
5. Returns to the previous menu by pressing
O RETURN.
Vocal
[Speaker selection]
Select a speaker that you want to adjust.
NOTE
3
Installation
[Test]
Select [Speaker Test Start] by using the U u
and press  ENTER. Press  ENTER again
to stop. Adjust the volume to match the
volume of test signals memorized in the
system.
DRC (Dynamic Range Control)
3. Use I i to select the desired speaker.
25
Select [On] to mix karaoke channels into
normal stereo.
This function is effective for multi-channel
karaoke DVDs only.
Certain speaker settings are prohibited by the
Dolby Digital licensing agreement.
HLT35W-F2_BPHLLL_ENG_6831.indd 25
2010-10-07 �� 3:37:34
26
Installation
HD AV Sync
Sometimes Digital TV encounters a delay
between picture and sound. If this happens
you can compensate by setting a delay on the
sound so that it effectively ‘waits’ for the picture
to arrive: this is called HD AV Sync. Use U u
(on the remote control) to scroll up and down
through the delay amount, which you can set
at anything between 0 and 300m sec.
Semi Karaoke
3
When a chapter/ title/ track is fully finished, this
function shows the score in the screen with a
fanfare sound.
Installation
[On]
When you finished singing a score will
appear on the screen.
[Off]
Fanfare and score do not appear on the
screen.
Lock (Parental Control)
Initial Setting the Area Code:
When you use this unit for the first time, you
have to set the Area Code.
1. Select the [Lock] menu and then press i.
2. Press i.
To access the [Lock] options, you must
input the password you have created. Input
a password and press  ENTER. Enter it
again and press  ENTER to verify. If you
make a mistake before pressing  ENTER,
press CLEAR.
3. Select the first character using U u buttons.
4. Press  ENTER and select the second
character using U u buttons.
5. Press  ENTER to confirm your Area code
selection.
Rating
NOTE
• DVD, DVD Karaoke discs with more than 2
tracks are available discs for this function.
• When you watch movies, “off ” the Semi
Karaoke at the SETUP menu or enjoy it without
connecting the MIC if the fanfare or score
appears during changing a chapter.
• This function operate on the DVD/CD mode.
• The Semi Karaoke function is available only
when a microphone is connected.
Connecting speakers
You can set up wireless connection manually,
when your connection is not completed. Refer
to page 15.
HLT35W-F2_BPHLLL_ENG_6831.indd 26
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
1. Select [Rating] on the [Lock] menu then
press i.
2. Input a password and press  ENTER.
3. Select a rating from 1 to 8 using the U u
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not
active and the disc plays in full.
4. Press  ENTER to confirm your rating
selection.
2010-10-07 �� 3:37:34
Installation
Password
You can enter or change password.
1. Select [Password] on the [Lock] menu and
then press i.
2. Press  ENTER.
3. Input a password and press  ENTER.
To change the password, press  ENTER
when the [Change] option is highlighted.
Input a password and press  ENTER. Enter
it again and press  ENTER to verify.
4. Press
HOME to exit the menu.
If you forget your password, you can clear it using
the following steps:
1. Select the [Setup] menu on the [Home] menu.
2. Input the 6-digit number “210499” and press
 ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards
were used to rate the DVD video disc, based
on the list on page 40.
1. Select [Area Code] on the [Lock] menu then
press i.
Others
DivX VOD
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, Inc. This is an official
DivX Certified device that plays DivX video.
Visit www.divx.com for more information and
software tools to convert your files into DivX
video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to
play DivX Video-on-Demand (VOD) content.
To generate the registration code, locate the
DivX VOD section in the device setup menu.
Go to vod.divx.com with this code to complete
the registration process and learn more about
DivX VOD.
[Register]
Displays the registration code of your player.
3
Installation
NOTE
27
[Deregister]
Deactivate your player and display the
deactivation code.
NOTE
All the downloaded videos from DivX VOD with
this player’s registration code can only be played
back on this unit.
2. Input a password and press  ENTER.
3. Select the first character using U u buttons.
4. Press  ENTER and select the second
character using U u buttons.
5. Press  ENTER to confirm your Area code
selection.
HLT35W-F2_BPHLLL_ENG_6831.indd 27
2010-10-07 �� 3:37:34
28
Operation
4
Operation
4
Using the Home Menu
Basic Operations
1. Press HOME.
Displays the [Home Menu].
1. Insert the disc by using the Z OPEN/
CLOSE or Connect the USB device to the
USB port.
2. Select an option by using I i.
Operation
3. Press  ENTER then selected option menu.
[Music] – Displays [MUSIC] menu.
[Movie] – Start video media’s playback or
display the [MOVIE] menu.
2. Press HOME.
Displays the [Home] Menu.
[Photo] – Displays [PHOTO] menu.
3. Select an option by using I i.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two
devices, it appears as belows. Select a
media then press  ENTER.
[Setup] – Displays the [Setup] menu.
NOTE
You can not select the [Music], [Movie] or [Photo]
option when the USB device is not connected or a
disc is not inserted.
4. Press  ENTER then selected option menu.
NOTE
• For the most Audio CD and DVD-ROM discs,
playback starts automatically.
• The unit plays only music file contained in the
USB storage device or disc automatically.
HLT35W-F2_BPHLLL_ENG_6831.indd 28
2010-10-07 �� 3:37:34
Operation
To
Stop
Do this
Press B (PLAY), MONO/
STEREO.
Pause
Press X (PAUSE/STEP).
Press X (PAUSE/STEP)
repeatedly to play title
Frame-by-Frame. (DVD, DivX
only)
During playback, press
Locating a
m/M SCAN repeatedly
point quickly
to select the required scan
by playing
speed.
a file in fast
To return to normal speed,
forward or fast
press B (PLAY), MONO/
reverse
STEREO.
Press s REPEAT
repeatedly, and the current
title, chapter or track will be
played back repeatedly or
randomly.
- DVD : Chapter/ Title/ Off
- DivX : Title/ All/ Off
- Audio CD/ MP3/ WMA :
Track/ All/ Random/ Off
Displaying Disc Information
on-screen
You can display various information about the
disc loaded on-screen.
1. Press INFO/DISPLAY to show various
playback information.
The displayed items differ depending on
the disc type or playing status.
2. You can select an item by pressing U u and
change or select the setting by pressing
I i.
Title – Current title number/ total number of
titles.
4
Chapter – C
urrent chapter number/ total
number of chapters.
Operation
During playback, press
./> SKIP to go to
Skipping to the next chapter/ track/
the next/
file or to return to the
previous
beginning of the current
chapter/ track/ chapter/ track/ file.
file
Press . SKIP twice
briefly to step back to the
previous chapter/ track/ file.
Playing
repeatedly or
randomly
Other Operations
Press x (STOP)
Playback
Frameby-Frame
playback
29
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – Selected angle/ total number of
angles.
NOTE
If any button is not pressed for a few seconds, the
on-screen display disappears.
In the pause mode, press
SLOW (bb or BB) to
Slowing down
select the required speed.
the playing
(DVD, DivX only) The DivX
speed
file cannot be slow down
reverse playback.
HLT35W-F2_BPHLLL_ENG_6831.indd 29
2010-10-07 �� 3:37:35
30
Operation
To display the DVD Menu
DVD
When you play a DVD which contains several
menu, you can select the menu you want
using the Menu.
1. Press DISC MENU.
The disc’s menu appears.
DVD
When you play a DVD which contains several
title, you can select the title you want using the
Menu.
4
1. Press TITLE.
The disc’s title appears.
Operation
2. Select the menu by pressing U u I i.
3. Press B (PLAY), MONO/STEREO to confirm.
1.5 times speed playback
3. Input the required start time in hours,
minutes, and seconds from left to right. If
you enter the wrong numbers, press CLEAR
to remove the numbers you entered. Then
input the correct numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by
using numerical buttons.
4. Press  ENTER to confirm. Playback starts
from the selected time.
Resume playback
DVD
DVD
The 1.5 speed allows you to watch the pictures
and listen to the sound quicker than playing at
a normal speed.
1. During playback, press B (PLAY), MONO/
STEREO to play at 1.5 times speed. “BX1.5”
appears on the screen.
2. Press B (PLAY), MONO/STEREO again to
exit.
Screen Saver
The screen saver appears when you leave the
unit in Stop mode for about five minutes.
HLT35W-F2_BPHLLL_ENG_6831.indd 30
INFO/DISPLAY during playback.
2. Press U u to select the time clock icon and
“--:--:--” appears.
3. Press B (PLAY), MONO/STEREO to confirm.
To start playing at any chosen time on the file
or title.
1. Press
2. Select the menu by using U u I i.
To display the DVD title
Starting play from selected
time DVD DivX
DivX
ACD
MP3
WMA
The unit records the point where you pressed
the x (STOP) depending on the disc.
If “Xx (Resume Stop)” appears on the screen
briefly, press B (PLAY), MONO/STEREO to
resume playback (from the scene point).
If you press x (STOP) twice or unload the disc,
“x”(Complete Stop) appears on the screen.
The unit will clear the stopped point.
NOTE
The resume point may be cleared when a button
is pressed (for example; 1 (POWER), Z OPEN/
CLOSE, etc).
2010-10-07 �� 3:37:35
Operation
Marked Playback
ACD
MP3
NOTE
WMA
The mark function enables you to store your
favourite files from any disc or USB device in
the unit memory.
1. Select [Music] on the [Home] menu.
Music menu
Returning to the upper
folder. (MP3/ WMA only)
File information will be displayed
according to the ID3TAG
information on the appropriate
music file. (MP3 only)
If you want to select all files on the list, select
[Select All] and press  ENTER.
To delete a Marker
1. Use U u to select the track that you wish to
erase from the marked file.
2. Press MARKER.
To delete all Markers
Use U u I i to select [Deselect All] then press
 ENTER in program edit mode.
NOTE
2. Select a desired music on the [List] by using
the U u then press MARKER to appear the
mark on the list.
3. Press  ENTER or B (PLAY), MONO/
STEREO.
Displays the play mode.
4. Select the play mode by using the U u and
press  ENTER.
4
Operation
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
Selecting all tracks/ files.
Deselecting all tracks/files.
Moving to the previous or
next file list.
31
Changing subtitle code page
DivX
If the subtitle is not displayed properly, you
can change the subtitle code page to view the
subtitle file properly.
1. During playback, press INFO/DISPLAY to
display the On-Screen display.
2. Use U u to select the [Code Page] option.
3. Use I i to select desired code option.
4. Press O RETURN to exit the On-Screen
display.
[Mark Play]
Marked playback.
[Current Play]
Normal playback
HLT35W-F2_BPHLLL_ENG_6831.indd 31
2010-10-07 �� 3:37:35
32
Operation
Viewing a PHOTO file
JPG
About help menu in the full screen.
This unit can play discs with photo files.
Menu
1. Select [Photo] on the [Home] menu and
press  ENTER.
Menu
Photo menu
Moving to the previous or
next file list.
Buttons
INFO/
DISPLAY
Operation
Displaying the
Option menu.
b/B
Prev./ Next
I/i
Moving to
another file
O Close
O
RETURN
Returning to
the [Photo]
menu.
Options while viewing a photo
You can use various options during viewing a
photo in full screen.
4
1. While viewing a photo in full screen, press
INFO/DISPLAY to display the option
menu.
Returning to the upper
folder.
Operation
2. Press U u to select a folder, and then press
 ENTER.
2. Select an option using U u I i.
3. If you want to view a slide show, press U
u to highlight a file and press B (PLAY),
MONO/STEREO.
About help menu in the [Photo] menu.
Menu
Buttons
BSlide
Show
B (PLAY),
MONO/
STEREO
vVbB
Move
a
Operation
Viewing a slide
show.
UuIi
Moving to
another file or
content.
b Slide Show N/ X– Press  ENTER to
start or pause slide show.
 Select
 ENTER
Viewing a
particular file.
O Close
O
RETURN
Returning to
the [Home]
menu.
HLT35W-F2_BPHLLL_ENG_6831.indd 32
b
c
d e
a Current photo/ Total number of photos
– Use I i to view previous/next photo.
c Speed x3/ x2/ x1 – Use  ENTER to
select a delaying speed between photos
in a slide show.
d Rotate – Press  ENTER to rotate the
photo.
e Go to list – Press  ENTER to return
[Photo] menu.
2010-10-07 �� 3:37:35
Operation
Sleep Timer Setting
System Select - Optional
Press SLEEP repeatedly to select the desired
time period options (in minutes):
(Display window off (LCD OFF) t Sleep timer
value t Display on)
In display window you see “LCD OFF” or Sleep
timer value and the display window turns off.
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then
press SLEEP once again while “SLEEP 10” is
displayed.
You must select the appropriate system mode
for your TV system. Press and hold X (PAUSE/
STEP) for more than five seconds to be able
to select a system in the [Home] menu. (PAL/
NTSC)
NOTE
• When you operate the unit in sleep mode,
you can see operating information in display
window for about 5 seconds and the display
window turns off.
Turn off the sound temporarily
Press
NOTE
If the USB device is connected or a disc is inserted,
this function is not operated.
Adjust the speaker level settings
You can adjust the sound level of each speaker.
1. Press SPEAKER LEVEL repeatedly to select
a desired speaker to set.
4
2. Press VOL -/+ to adjust the sound level of
the selected speaker while the level setting
memu is displayed on the display window.
Operation
• You can check the remaining time before the
unit turns off. Press SLEEP the remaining time
appears in the display window.
33
3. Repeat and adjust the sound level of the
other speakers.
MUTE to mute your unit.
You can mute your unit in order, for example,
to answer the telephone, appearing the MUTE
in the display window.
Last Scene Memory
DVD
This unit memorizes last scene from the last
disc that is viewed. The last scene remains in
memory even if you remove the disc from the
unit or switch off the unit. If you load a disc
that has the scene memorized, the scene is
automatically recalled.
VOCAL FADER
You can enjoy the function as karaoke, by
reducing singer vocal of music in the various
source. (MP3/ WMA/ CD/ etc.) Press the VOCAL
FADER, and “FADE ON” will appear in display
window.
To cancel it, press VOCAL FADER again.
The quality of the VOCAL FADER may
be different depending on the recording
conditions of music files.
NOTE
• This function is available to use only when a
microphone is connected.
• It is not available on the MONO source.
HLT35W-F2_BPHLLL_ENG_6831.indd 33
2010-10-07 �� 3:37:35
34
Operation
Radio Operations
Deleting all the saved stations
1. Press and hold CLEAR for two seconds.
"ERASE ALL" will flash up on the unit display.
Be sure that FM aerial is connected (Refer to
the page 22)
2. Press CLEAR to erase all saved of the radio
stations.
Listening to the radio
Deleting a saved station
1. Press t RADIO&INPUT until FM appears
in the display window.
The last received station is tuned in.
1. Press PRESET - / + to select a preset
number you want to delete.
2. Press and hold TUNING (-/+) for about
two seconds until the frequency indication
starts to change, then release. Scanning
stops when the unit tunes in a station.
4
Operation
or
3. Adjust the volume by rotating VOLUME on
the front panel or by pressing VOL (+/- )on
the remote control repeatedly.
Press TUNING (-/+) repeatedly.
2. Press CLEAR, the preset number will blink
in the display window.
3. Press CLEAR again, to delete the selected
preset number.
Improving poor FM reception
Press B (PLAY), MONO/STEREO on the
remote control. This will change the tuner
from stereo to mono and usually improve the
reception.
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
1. Press t RADIO&INPUT until FM appears
in the display window.
2. Select the desired frequency by using
TUNING (-/+).
3. Press  ENTER a preset number will flash
in the display window.
4. Press PRESET (-/+) to select the preset
number you want.
5. Press  ENTER.
The station is stored.
6. Repeat the steps 2 to 5 to store other
stations.
HLT35W-F2_BPHLLL_ENG_6831.indd 34
2010-10-07 �� 3:37:35
Operation
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound
mode by using SOUND EFFECT.
You can change the SOUND EFFECT using
I i arrow key while the sound effect
information is displayed on.
The displayed items for the equalizer may be
different depending on sound sources and
effects.
Description
NAT PLUS
The NAT PLUS is Natural Plus
sound effect. You can enjoy the
natural sound effect same as a
5.1-channel.
NATURAL
You can enjoy comfortable and
natural sound.
Local
specialization
equalizer
Regionally optimized sound
effect. (DANGDUT/ ARABIC/
PERSIAN/ INDIA/ REGUETON/
MERENGUE/
SAMBA/ SALSA/ CUMBIA/
AFRO)
AUTO EQ
Realizes the sound equalizer
that is the most similar to the
genre of which is included in
the MP3 ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock pop,
jazz or classic concert.
BASS
The BASS is Bass Blast. During
playback, reinforce the treble,
bass and surround sound effect.
HLT35W-F2_BPHLLL_ENG_6831.indd 35
Description
CLRVOICE
The CLRVOICE is Clear Voice.
This program make voice sound
clear, improving the quality of
voice sound. (We encourage
to use this EQ when you watch
the movie of 5.1 channel.)
GAME
The GAME is Game Equalizer.
You can enjoy more virtual
sound while playing video
games.
NIGHT
The NIGHT is Night Mode. This
may be useful when you want
to watch movies at low volume
late at night.
RETOUCH
The RETOUCH is MP3 UpScaling. When listening to
MP3 files or other compressed
music, you can enhance the
sound. This mode is available
only to 2 channel sources.
LOUDNESS
Improves the bass and treble
sound.
VIRTUAL
The VIRTUAL is VSM Plus. You
can enjoy more virtual surround
sound.
BYPASS
You can enjoy the sound
without equalizer effect.
4
Operation
On Display
On Display
35
NOTE
• In some of surround modes, some speakers,
there's no sound or low sound. It depends on
the mode of surround and the source of audio,
it is not defective.
• You may need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
• This function is not operated when the
microphone is connected to the unit.
2010-10-07 �� 3:37:35
36
Operation
Advanced Operations
Recording to USB
You can record music or sound souce to USB
device by connecting to the port on the unit.
1. Connect the USB device to the unit.
2. Select a mode in which you want to record.
Play back a sound source first.
3. Start the recording by pressing z REC.
4. To stop recording, press x (STOP).
[All tracks/ files recording]
Record to USB in stop or play mode.
4
Operation
[Program list recording]
After marking desired file(s) and you can
record it to USB (Refer to the page 31).
It'll be stored as follows
NOTE
• You can check the recording percentage rate
for the USB record on the screen during the
recording. (Audio CD or MP3/ WMA CD only)
• During recording MP3/WMA, there is no
sound.
• When you stop recording during playback, the
file that has been recorded at that time will be
stored. (Audio CD only)
• Do not remove the USB device or turn off
the unit during USB recording. If not, an
incomplete file may be made and not deleted
on PC.
• Recording through microphones is not
availabe.
• If USB recording does not work, the message
like “NO USB”, “ERROR”, “USB FULL” or “NO REC” is
displayed on the display window.
• Multi card reader divice or external HDD can
not be used for USB recording.
• A file is recorded by 128 Mbyte (about 2 hours)
when you record for a long term. There are
recorded less than 4 files.
• When you stop recording during playback, the
file will not be stored.
Audio CD
MP3/ WMA
The other
sources
(Tuner, AUX,
Portable)
• In the state CD-G, DTS disc USB record is not
operated.
• The files in the sub-folders are not recorded
during all track recording.
• You may not record more than 999 files.
• The numbering of the recording file is entered
from the lowest number. So if you delete some
of the recording files, the next recording file
could be the lowest number among them.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and
constitute a criminal offense. This equipment
should not be used for such purposes.
Be responsible
Respect copyrights.
HLT35W-F2_BPHLLL_ENG_6831.indd 36
2010-10-07 �� 3:37:35
Maintenance
37
5
Maintenance
Notes on Discs
Handling the Unit
Handling Discs
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit,
for maximum protection, re-pack the unit as it
was originally packed at the factory.
Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
• Do not use volatile liquids such as
insecticide spray near the unit.
• Wiping with strong pressure may damage
the surface.
• Do not leave rubber or plastic products in
contact with the unit for a long period of
time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If
the surfaces are extremely dirty, use a soft
cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as
alcohol, benzine, or thinner, as these might
damage the surface of the unit.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.
HLT35W-F2_BPHLLL_ENG_6831.indd 37
5
Maintenance
Cleaning Discs
Keeping the exterior surfaces clean
Maintaining the Unit
The unit is a high-tech, precision device. If
the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality could be
diminished. For details, please contact your
nearest authorized service center.
2010-10-07 �� 3:37:36
38
Troubleshooting
6
Troubleshooting
PROBLEM
CAUSE
CORRECTION
Plug the power cord into the wall outlet
No power
The power cord is disconnected.
securely.
Select the appropriate video input mode
The TV is not set to receive the DVD signal. on the TV so the picture from the unit
appears on the TV screen.
No picture
The video cables are not connected
Connect the video cables securely to both
securely.
the TV and unit.
Equipment connected via the audio cable Select the correct input mode of the unit
is not set to receive DVD signal output.
so you can hear the sound from the unit.
There is little or The audio cables are not connected to the Connect the audio cables into the
no sound
speakers or unit securely.
connection terminals correctly.
The audio cables are damaged.
Replace with a new audio cable.
The DVD picture The disc is dirty.
quality is poor
No disc is inserted.
A DVD/CD will
not play
6
Troubleshooting
Humming noise
heard while a
DVD or CD is
playing
Radio stations
can’t be tuned in
properly
The remote
control doesn’t
work well / at all
Clean the disc using a soft cloth with
outward strokes.
Insert a disc.
Insert a playable disc (check the disc type,
An unplayable disc is inserted.
colour system and regional code).
Place the disc with the label or printed
The disc is inserted upside down.
side facing upwards.
There is a parental lock which prevents the Enter your password or change the rating
playback of DVDs with a certain rating.
level.
Clean the disc using a soft cloth with
The disc is dirty.
outward strokes.
The unit is located too close to the TV,
Move unit and audio components further
causing feedback.
away from your TV.
Check the antenna connection and adjust
The antenna is positioned or connected
its position.
poorly.
Attach an external aerial if necessary.
The signal strength of the radio station is
Tune to the station manually.
too weak.
No stations have been preset or preset
Preset some radio stations, see page 34 for
stations have been cleared (when tuning
details.
by scanning preset channels).
The remote is not pointed directly at the
Point the remote directly at the unit.
unit.
Use the remote within 23 feet (7m) of the
The remote is too far from the unit.
unit.
There is an obstacle in the path between
Remove the obstacle.
the remote control and the unit.
The batteries in the remote control are flat. Replace the batteries with new ones.
HLT35W-F2_BPHLLL_ENG_6831.indd 38
2010-10-07 �� 3:37:36
Appendix
39
7
Appendix
Language Codes
Use this list to input your desired language for the following initial settings: Disc Audio, Disc
Subtitle, Disc Menu.
Code
Language Code
Language Code
Language Code
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
9072
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
French Frisian Galician Georgian German Greek Greenlandic Guarani Gujarati Hausa Hebrew Hindi Hungarian Icelandic Indonesian Interlingua Irish Italian Javanese Kannada Kashmiri Kazakh Kirghiz Korean Kurdish Laothian Latin Latvian, Lettish Lingala 7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
7678
Lithuanian Macedonian Malagasy Malay Malayalam Maori Marathi Moldavian Mongolian Nauru
Nepali Norwegian Oriya Panjabi Pashto, Pushto Persian Polish Portuguese Quechua Rhaeto-Romance Rumanian Russian Samoan Sanskrit Scots Gaelic Serbian Serbo-Croatian Shona Sindhi 7684
7775
7771
7783
7776
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Singhalese Slovak Slovenian Spanish Sudanese Swahili Swedish Tagalog Tajik Tamil Telugu Thai Tonga Turkish Turkmen Twi Ukrainian Urdu Uzbek Vietnamese Volapük Welsh Wolof Xhosa Yiddish Yoruba Zulu 8373
8375
8376
6983
8385
8387
8386
8476
8471
8465
8469
8472
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
HLT35W-F2_BPHLLL_ENG_6831.indd 39
Appendix
Language Afar Afrikaans Albanian Ameharic Arabic Armenian Assamese Aymara Azerbaijani Bashkir Basque Bengali; Bangla Bhutani Bihari Breton Bulgarian Burmese Byelorussian Chinese Croatian Czech Danish Dutch English Esperanto Estonian Faroese Fiji Finnish 7
2010-10-07 �� 3:37:36
40
Appendix
Area Codes
Choose an area code from this list.
Appendix
Area Afghanistan Argentina Australia Austria Belgium Bhutan Bolivia Brazil Cambodia Canada Chile China Colombia Congo Costa Rica Croatia Czech Republic Denmark Ecuador Egypt El Salvador Ethiopia Fiji Finland France Germany Great Britain Greece Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
ET
FJ
FI
FR
DE
GB
GR
Area Greenland Hong Kong Hungary India Indonesia Israel Italy Jamaica Japan Kenya Kuwait Libya Luxembourg Malaysia Maldives Mexico Monaco Mongolia Morocco Nepal Netherlands Netherlands Antilles New Zealand Nigeria Norway Oman Pakistan Panama Code
GL
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
LU
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
Area Paraguay Philippines Poland Portugal Romania Russian Federation Saudi Arabia Senegal Singapore Slovak Republic Slovenia South Africa South Korea Spain Sri Lanka Sweden Switzerland Taiwan Thailand Turkey Uganda Ukraine United States Uruguay Uzbekistan Vietnam Zimbabwe Code
PY
PH
PL
PT
RO
RU
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
7
HLT35W-F2_BPHLLL_ENG_6831.indd 40
2010-10-07 �� 3:37:36
Appendix
Trademarks and
Licenses
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
41
What is SIMPLINK?
Some functions of this unit are controlled
by TV’s remote control when this unit
and LG TV with SIMPLINK are connected
through HDMI connection. Controllable
functions by LG TV’s remote control; Play,
Pause, Scan, Skip, Stop, Power Off, etc.
• Refer to the TV owner’s manual for the
details of SIMPLINK function.
• LG TV with SIMPLINK function has the
logo as shown above.
• Use a higher version cable than 1.2 A
HDMI cable.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
Appendix
DivX is a registered trademark of DivX, Inc., and is
used under license.
7
HLT35W-F2_BPHLLL_ENG_6831.indd 41
2010-10-07 �� 3:37:36
42
Appendix
Specifications
Amplifier
• Stereo mode: 75 W + 75 W (4 Ω at 1 kHz)
• Subwoofer 150 W (3 Ω at 60 Hz)
General
• Power requirements:
Refer to main label.
• Power consumption:
Refer to main label.
• Dimensions (W x H x D):
800 X 160 X 80 mm without foot
• Net Weight (Approx.):
4.6 kg
• Operating temperature:
41 °F to 95 °F (5 °C to 35 °C)
• Operating humidity:
5 % to 90 %
• Bus Power supply (USB):
DC 5 V
500 mA
Inputs/ Outputs
• VIDEO OUT:
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
Wireless subwoofer
• Power requirements:
Refer to main label on the Subwoofer.
• Power consumption:
Refer to main label on the Subwoofer.
• Reception Output:
5.8 GHz
• Subwoofer
Type: Impedance Rated: Input Power: Max. Input power: Net Dimensions (W x H x D): Net Weight: 1 Way 1 speaker
3Ω
150 W
300 W
196 x 390 x 356 mm
7.1 kg
Designs and specifications are subject to change
without prior notice.
Appendix
• HDMI OUT (video/audio):
19 pin (HDMI standard, Type A)
HDMI version : 1.2A
• ANALOG AUDIO IN:
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
• DIGITAL IN (OPTICAL IN):
3 V (p-p), Optical jack x 1
• PORT. IN:
0.5 Vrms (3.5 mm stereo jack)
7
Tuner
• FM Tuning Range:
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
HLT35W-F2_BPHLLL_ENG_6831.indd 42
2010-10-07 �� 3:37:37
HLT35W-F2_BPHLLL_ENG_6831.indd 43
2010-10-07 �� 3:37:37
Download PDF

advertising