OWNER’S MANUAL LCD TV Please read this manual carefully before operating your set and retain it for future reference. CS56** P/NO : MFL67466613 (1205-REV03) Printed in Korea www.lg.com 2 TABLE OF CONTENTS ENGLISH ENG TABLE OF CONTENTS 2 TABLE OF CONTENTS 25 TROUBLESHOOTING 3 LICENSES 26 SPECIFICATIONS 3 OPEN SOURCE SOFTWARE NOTICE 4 SAFETY INSTRUCTIONS 10 INSTALLATION PROCEDURE 10 ASSEMBLING AND PREPARING 10 13 14 15 15 16 18 18 Unpacking Parts and buttons Lifting and moving the TV Setting up the TV Tidying cables Mounting on a table Mounting on a wall Not using the Desk Type stand 19 MAKING CONNECTIONS 19 20 20 21 21 22 22 22 22 Antenna connection HDMI connection DVI to HDMI connection Component connection Composite connection RGB-PC connection USB connection Audio connection - Digital optical audio connection 23 REMOTE CONTROL 24 USING THE USER GUIDE 25 MAINTENANCE 25 25 25 Cleaning your TV - Screen, frame, cabinet and stand - Power cord WARNING yy If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION yy If you ignore the caution message, you may be slightly injured or the product may be damaged. NOTE yy The note helps you understand and use the product safely. Please read the note carefully before using the product. LICENSES / OPEN SOURCE SOFTWARE NOTICE 3 Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration. “DivX Certified® to play DivX® video up to HD 1080p, including premium content.” “DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.” “Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274” OPEN SOURCE SOFTWARE NOTICE To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com . In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product. ENGLISH ENG LICENSES 4 SAFETY INSTRUCTIONS ENGLISH ENG SAFETY INSTRUCTIONS Please read these safety precautions carefully before using the product. WARNING Do not place the TV and remote control in the following environments: yy --A location exposed to direct sunlight --An area with high humidity such as a bathroom --Near any heat source such as stoves and other devices that produce heat --Near kitchen counters or humidifiers where they can easily be exposed to steam or oil --An area exposed to rain or wind --Near containers of water such as vases Otherwise, this may result in fire, electric shock, malfunction or product deformation. Do not place the product where it might be exposed to dust. y yy This may cause a fire hazard. Mains plug is the disconnecting device. The plug must remain readily operable. yy Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or yy covered with dust, dry the power plug completely or wipe dust off. y You may be electrocuted due to excess moisture. Make sure to connect the power cable to the grounded current. (Except for devices yy which are not grounded.) You may be electrocuted or injured. Fix the power cable completely. y yy If the power cable is not fixed completely, a fire can break out. Ensure the power cord does not come into contact with hot objects such as a yy heater. y This may cause a fire or an electric shock hazard. Do not place a heavy object, or the product itself, on power cables. y yy Otherwise, this may result in fire or electric shock. Bend antenna cable between inside and outside building to prevent rain from yy flowing in. y This may cause water damaged inside the Product and could give an electric shock. When mounting a TV it on the wall, make sure not to install TV by hanging power yy and signal cables on the back of the TV. y It may cause fire, electric shock. SAFETY INSTRUCTIONS Do not drop the product or let it fall over when connecting external devices. y yy Otherwise, this may result in injury or damage to the product. Keep the packing anti-moisture material or vinyl packing out of the reach of yy children. y Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children. Do not let your children climb or cling onto the TV. y yy Otherwise, the TV may fall over, which may cause serious injury. Dispose of used batteries carefully to protect a child from eating them.y yy Please seek Doctor- Medical Attention immediately if child consumes batteries. Do not insert any metal objects/conductors (like a metal chopstick/cutlery/ yy screwdriver) between power cable plug and input Wall Socket while it is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal.y You may be electrocuted.y (Depending on model) Do not put or store inflammable substances near the product. There is a danger yy of combustion/explosion or fire due to careless handling of the inflammable substances. Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the yy product, or inflammable objects such as paper and matches. Children must pay particular attention. y Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service centre. Do not spray water on the product or scrub with an inflammable substance (thinner yy or benzene). Fire or electric shock accident can occur. Do not allow a impact shock or any objects to fall into the product, and do not drop yy onto the screen with something. y You may be injured or the product can be damaged. Never touch this product or antenna during a thunder or lighting storm. y yy You may be electrocuted. Never touch the wall outlet when there is leakage of gas, open the windows and yy ventilate. y It may cause a fire or a burn by a spark. ENGLISH ENG Do not plug too many electrical devices into a single multiple electrical outlet. y yy Otherwise, this may result in fire due to over-heating. 5 6 SAFETY INSTRUCTIONS ENGLISH ENG Do not disassemble, repair or modify the product at your own discretion. y yy Fire or electric shock accident can occur. y Contact the service center for check, calibration or repair. If any of the following occur, unplug the product immediately and contact your local yy service centre. --The product has been impacted by shock --The product has been damaged --Foreign objects have entered the product --The product produced smoke or a strange smell This may result in fire or electric shock. If you don’t intend to use the product for a long time, unplug the power cable from yy the product. y Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire. Apparatus shall not be exposed to dripping or splashing and no objects filled with yy liquids, such as vases, shall be placed on the apparatus. SAFETY INSTRUCTIONS Install the product where no radio wave occurs. yy There should be enough distance between an outside antenna and power lines to yy keep the former from touching the latter even when the antenna falls. y This may cause an electric shock. Do not install the product on places such as unstable shelves or inclined surfaces. yy Also avoid places where there is vibration or where the product cannot be fully supported. y Otherwise, the product may fall or flip over, which may cause injury or damage to the product. If you install the TV on a stand, you need to take actions to prevent the product yy from overturning. Otherwise, the product may fall over, which may cause injury. If you intend to mount the product to a wall, attach VESA standard mounting interface (optional yy parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop. Only use the attachments / accessories specified by the manufacturer. yy When installing the antenna, consult a qualified service man. y yy This may create a fire hazard or an electric shock hazard. We recommend that you maintain a distance of at least 5 to 7 times the diagonal yy screen size when watching TV. y If you watch TV for a long period of time, this may cause blurred vision. Only use the specified type of battery. y yy This could cause damage to the remote control. Do not mix new batteries with old batteries. y yy This may cause the batteries to overheat and leak. Make sure there are no objects between the remote control and its sensor. yy Signal from the remote control may be disturbed by sun light or other strong light. yy In this case, darken the room. When connecting external devices such as video game consoles, make sure the yy connecting cables are long enough. y Otherwise, the product may fall over, which may cause injury or damage the product. ENGLISH ENG CAUTION 7 8 SAFETY INSTRUCTIONS ENGLISH ENG Do not turn the product On/Off by plugging-in or unplugging the power plug to the yy wall outlet. (Do not use the power plug for switch.) y It may cause mechanical failure or could give an electric shock. Please follow the installation instructions below to prevent the product from yy overheating. --The distance between the product and the wall should be more than 10 cm. --Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard). --Do not install the product on a carpet or cushion. --Make sure the air vent is not blocked by a tablecloth or curtain. Otherwise, this may result in fire. Take care not to touch the ventilation openings when watching the TV for long yy periods as the ventilation openings may become hot. This does not affect the operation or performance of the product. Periodically examine the cord of your appliance, and if its appearance indicates damage or yy deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Prevent dust collecting on the power plug pins or outlet. y yy This may cause a fire hazard. Protect the power cord from physical or mechanical abuse, such as being twisted, yy kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not press strongly upon the panel with a hand or sharp object such as nail, yy pencil or pen, or make a scratch on it. Avoid touching the screen or holding your finger(s) against it for long periods of yy time. Doing so may produce some temporary distortion effects on the screen. When cleaning the product and its components, unplug the power first and wipe it yy with a soft cloth. Applying excessive force may cause scratches or discolouration. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol etc., which can damage the product and its panel. y Otherwise, this may result in fire, electric shock or product damage (deformation, corrosion or breakage). As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power yy source even if you turn off this unit by SWITCH. When unplugging the cable, grab the plug and unplug it. y yy If the wires inside the power cable are disconnected, this may cause fire. When moving the product, make sure you turn the power off first. Then, unplug the yy power cables, antenna cables and all connecting cables. y The TV set or power cord may be damaged, which may create a fire hazard or cause electric shock. SAFETY INSTRUCTIONS Contact the service center once a year to clean the internal parts of the product. y yy Accumulated dust can cause mechanical failure. Refer all servicing to qualified service personnel. Servicing is required when the yy apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. If the product feels cold to the touch, there may be a small “flicker” when it is turned yy on. This is normal, there is nothing wrong with product. The panel is a high technology TFT product with resolution of two million to six yy million pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not affect the performance and reliability of the product. y This phenomenon also occurs in third-party products and is not subject to exchange or refund. You may find different brightness and colour of the panel depending on your yy viewing position(left/right/top/down). y This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction. Displaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video yy game) for a prolonged time may cause damage to the screen, resulting in retention of the image, which is known as image sticking. The warranty does not cover the product for image sticking. y Avoid displaying a fixed image on your television’s screen for a prolonged period (2 or more hours for LCD, 1 or more hours for Plasma). y Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders of the panel. y This phenomenon also occurs in third-party products and is not subject to exchange or refund. yyGenerated Sound “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to tempera-ture and humidity. This noise is common for products where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depend-ing on the product. y This generated sound does not affect the performance and reliability of the product. ENGLISH ENG When moving or unpacking the product, work in pairs because the product is yy heavy. y Otherwise, this may result in injury. 9 10 INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING ENGLISH ENG NOTE yy Image shown may differ from your TV. yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. yy The available menus and options may differ from the input source or product model that you are using. yy New features may be added to this TV in the future. yy The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned off if it will not be watched for some time, as this will reduce energy consumption. yy The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost. INSTALLATION PROCEDURE 1 2 3 4 Open the package and make sure all the accessories are included. Attach the stand to the TV set. Connect an external device to the TV set. Make sure the network connection is available.y You can use the TV network functions only when the network connection is made. ASSEMBLING AND PREPARING Unpacking Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item. CAUTION yy Do not use any unapproved items to ensure the safety and product life span. yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty. yy Some models have a thin film attached on to the screen and this must not be removed. NOTE yy The items supplied with your product may vary depending on the model. yy Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions. yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port. B B A A *A < = 10 mm *B < = 18 mm ASSEMBLING AND PREPARING Owner’s manual Polishing cloth (Depending on model) Use this to remove dust from the cabinet. Power Cord Stand Screws 8 EA, M4 x 20 (See p. 15) Desk-mount Screw (Only 32/37/42CS56**) (See p. 16) Isolator (Depending on model) (See p.12) Protection cover (See p. 18) Stand Body / Stand Base (See p. 15) ENGLISH ENG or Remote control and batteries (AAA) (See p. 23) 11 12 ASSEMBLING AND PREPARING ENGLISH ENG CAUTION yy Power Cord Installation Guide -- If the power cord provided with TV looks like the below picture, please ensure that it is inserted in the right direction.y TV Power Cord Correct Wrong NOTE yy Antenna Isolator Installation Guide -- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal. »» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an accident. -- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation. -- Before starting, be sure that the TV antenna is connected. 1. Connect to TV. Wall ANTENNA/ CABLE IN Cable / Antenna or Isolator 2. Connect to Set-Top box. Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box. “Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing - and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)” When applying the RF Isolator, a slight loss of signal sensitivity can occur. ASSEMBLING AND PREPARING ENGLISH ENG Parts and buttons Screen Remote control andy intelligent sensors1 Power indicator Speakers OK Touch Button SETTINGS INPUT Touch buttons2 Description Scrolls through the saved programmes. H Adjusts the volume level. H 13 OK Selects the highlighted menu option or confirms an input. SETTINGS Accesses the main menu, or saves your input and exits the menus. INPUT Changes the input source. /I Turns the power on or off. 1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. 2 All of the buttons are touch sensitive and can be operated through simple touch with your finger. NOTE yy You can set the power indicator light to on or off by selecting OPTION in the main menus. 14 ASSEMBLING AND PREPARING ENGLISH ENG Lifting and moving the TV Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. yy When transporting a large TV, there should be at least 2 people. yy When transporting the TV by hand, hold the TV as shown in the following illustration.y CAUTION yy Avoid touching the screen at all times, as this may result in damage to the screen. yy It is recommended to move the TV in the box or packing material that the TV originally came in. yy Before moving or lifting the TV, disconnect the power cord and all cables. yy When holding the TV, the screen should face away from you to avoid damage.y yy Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.y yy When transporting the TV, do not expose the TV to jolts or excessive vibration. yy When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right. ASSEMBLING AND PREPARING CAUTION 1 M4 x 20 Stand Body 4EA Front yy When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. yy Make sure that the screws are inserted correctly and fastened securely. (If they are not fastened securely enough, the TV may tilt forward after being installed.)y Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly. NOTE Stand Base yy Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. Top View 2 3 Tidying cables 1 Use Cable Management to neatly secure and position cables together. 2 Fix the Cable Management firmly to the TV. M4 x 20 4EA Cable Management ENGLISH ENG Setting up the TV 15 16 ASSEMBLING AND PREPARING ENGLISH ENG Mounting on a table 1 Lift and tilt the TV into its upright position on a table. -- Leave a 10 cm (minimum) space from the wall for proper ventilation. Adjusting the angle of the TV to suit view Swivel 20 degrees to the left or right and adjust the angle of the TV to suit your view. 20 20 10 cm 10 cm m 10 c 10 cm 2 Connect the power cord to a wall outlet. CAUTION yy Do not place the TV near or on sources of heat, as this may result in fire or other damage. Securing the TV to a table Fix the TV to a table to prevent from tilting forward, damage, and potential injury. (Only 32/37/42CS56**) To secure the TV to a table, insert and tighten the supplied screw on the rear of the stand. WARNING yy To prevent TV from falling over, the TV should be securely attached to the floor/ wall per installation instructions. Tipping, shaking, or rocking the TV may cause injury. CAUTION yy When adjusting the angle of the product, watch out for your fingers. -- Personal injury may occur if hands or fingers are pinched. If the product is tilted too much, it may fall, causing damage or injury. ASSEMBLING AND PREPARING (This feature is not available for all models.) Using the Kensington security system (This feature is not available for all models.) The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit . Connect the Kensington security system cable between the TV and a table. 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. -- If there are bolts inserted at the eye-bolts position, remove the bolts first. 2 Mount the wall brackets with the bolts to the wall.y Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.y Make sure to keep the rope horizontal with the flat surface. CAUTION yy Make sure that children do not climb on or hang on the TV. NOTE yy Use a platform or cabinet that is strong and large enough to support the TV securely. yy Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer. ENGLISH ENG Securing the TV to a wall 17 18 ASSEMBLING AND PREPARING ENGLISH ENG Mounting on a wall Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer. 10 cm 10 cm 10 cm yy Disconnect the power first, and then move or install the TV. Otherwise electric shock may occur. yy If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury.y Use an authorized LG wall mount and contact the local dealer or qualified personnel. yy Do not over tighten the screws as this may cause damage to the TV and void your warranty. yy Use the screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the manufacturer’s warranty. NOTE 10 cm Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table. Separate purchase (Wall Mounting Bracket) Model VESA (A x B) Standard screw Number of screws Wall mount bracket CAUTION 32CS56** 200 x 100 M4 37/42/47CS56** 200 x 200 M6 4 4 LSW100B LSW200BX LSW220BX yy Use the screws that are listed on the VESA standard screw specifications. yy The wall mount kit includes an installation manual and necessary parts. yy The wall mount bracket is not provided. You can obtain additional accessories from your local dealer. yy The length of screws may differ depending on the wall mount. Make sure to use the proper length. yy For more information, refer to the manual supplied with the wall mount. Not using the Desk Type stand Push the supplied Protection cover into the opening at the bottom of the TV until clicking sound. A B Protection Cover MAKING CONNECTIONS Antenna connection Connect the TV to a wall antenna socket with an RF cable (75 Ω). This section on MAKING CONNECTIONS mainly uses diagrams for the 32/37/42/47CS56** models. Connect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device. Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. ANTENNA / CABLE IN NOTE yy The external device connection may differ from the model. yy Connect external devices to the TV regardless of the order of the TV port. yy If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information of recording, refer to the manual provided with the connected device. yy Refer to the external equipment’s manual for operating instructions. yy If you connect a gaming device to the TV, use the cable supplied with the gaming device. yy In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. yy In PC mode, some resolution settings may not work properly depending on the graphics card. NOTE yy Use a signal splitter to use more than 2 TVs. yy If the image quality is poor, install a signal amplifier properly to improve the image quality. yy If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction. yy An antenna cable and converter are not supplied. ENGLISH ENG MAKING CONNECTIONS 19 20 MAKING CONNECTIONS DVI to HDMI connection Transmits the digital video and audio signals from an external device to the TV. Connect the external device and the TV with the HDMI cable as shown. Transmits the digital video signal from an external device to the TV. Connect the external device and the TV with the DVI-HDMI cable as shown. To transmit an audio signal, connect an audio cable. Choose any HDMI input port to connect. It does not matter which port you use. Choose any HDMI input port to connect. It does not matter which port you use. 3 ENGLISH ENG HDMI connection AUDIO IN (RGB/DVI) / DVI IN 1 2 / DVI IN 1 2 (*Not Provided) (*Not Provided) HDMI DVD/ Blu-Ray / HD Cable Box / HD STB / PC NOTE yy It is recommended to use the HDMI connection for the best image quality. yy Use the latest High Speed HDMI™ Cable with CEC (Customer Electronics Control) function. yy High Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher. yy DTV Audio supported Codec: MPEG, Dolby Digital, Dolby Digital Plus, HE-AAC yy HDMI Audio supported format : Dolby Digital, PCM (Up to 192 KHz, 32k/44.1k/48k /88k/96k/176k/192k, DTS Not supported) DVI OUT AUDIO OUT DVD/ Blu-Ray / HD Cable Box / PC NOTE yy Depending on the graphics card, DOS mode video may not work if a HDMI to DVI Cable is in use. MAKING CONNECTIONS 21 Composite connection Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with a component cable as shown. Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with th e composite cable as shown. AV IN VIDEO L/MONO AUDIO R AV IN VIDEO 2 L/MONO AUDIO R 2 Y PB PR L R Y PR L AUDIO VIDEO COMPONENT IN (*Not Provided) VIDEO RED L RED WHITE RED BLUE GREEN VIDEO WHITE YELLOW (*Not Provided) L R RED RED WHITE RED BLUE GREEN AUDIO VIDEO COMPONENT IN PB WHITE 1 YELLOW 1 R AUDIO R AUDIO VCR / DVD / Blu-Ray / HD Cable Box DVD / Blu-Ray / HD Cable Box NOTE yy If cables are installed incorrectly, it could case the image to display in black and white or with distorted colour. ENGLISH ENG Component connection 22 MAKING CONNECTIONS Audio connection Transmits the video signal from PC to the TV. To transmit an audio signal, connect an audio cable. You may use an optional external audio system instead of the built-in speaker. AUDIO IN (RGB/DVI) NOTE yy If you use an optional external audio device instead of the built-in speaker, set the TV speaker feature to off. RGB IN (PC) Digital optical audio connection Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV with the optical audio cable as shown. (*Not Provided) OPTICAL DIGITAL AUDIO OUT RGB OUT (PC) AUDIO OUT PC (*Not Provided) USB connection Connect a USB storage device such as s USB flash memory, external hard drive or a USB memory card reader to the TV and access the My media menu to use various multimedia files. USB IN ENGLISH ENG RGB-PC connection OPTICAL AUDIO IN Digital Audio System NOTE yy Do not look into the optical output port. Looking at the laser beam may damage your vision. yy Audio with ACP (Audio Copy Protection) function may block digital audio output. USB device (*Not Provided) REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION yy Do not mix old and new batteries, as this may damage the remote control. yy In Analogue TV and some countries, some remote control buttons may not work. Make sure to point the remote control toward the remote control sensor on the TV. Adjusts the brightness of the screen to reduce energy consumption. Selects Radio, TV and DTV programme. Navigation buttons (up/down/left/right) 1 2 3 1 Coloured buttons 2 Control buttons ( 3 TELETEXT BUTTONS ) Shows programme guide. Views the information of the current programme and screen. Resizes an image. Changes the input source. Accesses the saved programme list. Returns to the previously viewed programme. Accesses the main menus. Accesses the Quick menus. Scrolls through menus or options. Moves to the previous or next screen. Returns to the previous level. Clears on-screen displays and return to TV viewing. Accesses your favourite programme list. Accesses the AV devices connected with the HDMI cable through HDMI-CEC. Opens the SIMPLINK menu. Moves to the previous or next screen. These access special functions in some menus. ( : Red, : Green, : Yellow, : Blue) Controls the MY MEDIA menus, or the SIMPLINK compatible devices (USB,SIMPLINK). Recalls your preferred subtitle in digital mode. These buttons are used for teletext. ENGLISH ENG REMOTE CONTROL 23 24 USINGyTHEyUSERyGUIDE ENGLISH ENG USING THE USER GUIDE UseryGuideyallowsyyouytoymoreyeasilyyaccessytheydetailedyTVyinformation. 1y PressySETTINGSytoyaccessytheymainymenus. 2y PressytheyREDybuttonytoyaccessytheyCustomer Supportymenus. 3y PressytheyNavigationybuttonsytoyscrollytoyUser GuideyandypressyOK. UseryGuide 1 PROGRAMMEySetting PICTURE,ySOUNDySetting OPTION OPTIONy>yToysetylanguage SETTINGy y yOPTIONy yLanguage Youycanyselectytheylanguageyofytheymenuydisplayedyonytheyscreenyandythey digitalysoundybroadcasting. yyyMenuyLanguagey:ySelectsyaylanguageyforytheydisplayytext. yyyAudioyLanguageyyy[InyDigitalyModeyOnly]y:ySelectytheydesiredylanguagey whenywatchingydigitalybroadcastingycontaingyseveraly voiceylanguages. yyySubtitleyLanguageyy[InyDigitalyModeyOnly]y:yUseytheySubtitleyfunctionywheny twoyorymoreysubtitleylanguagesyareybroadcast. y yyIfysubtitleydatayinyayselectedylanguageyisynotybroadcast,ytheydefaultylanguageysubtitleywillybeydisplayed. AdvabcedyFunction Information PICTURE AUDIO SETUP TIME LOCK OPTION NETWORK MYyMEDIA PressyOK()ytoysetyyourypictureysettings. CustomerySupport 2 ZoomyIn Close SETTINGy y yOPTIONy yLanguage Youycanyselectytheylanguageyofytheymenuydisplayedyonytheyscreenyandythey digitalysoundybroadcasting. yyyMenuyLanguagey:ySelectsyaylanguageyforytheydisplayytext. yyyAudioyLanguageyyy[InyDigitalyModeyOnly]y:yelectytheydesiredylanguageywheny watchingydigitalybroadcastingycontaingyseveralyvoicey languages. yyySubtitleyLanguageyy[InyDigitalyModeyOnly]y:yUseytheySubtitleyfunctionywheny twoyorymoreysubtitleylanguagesyareybroadcast. y yyIfysubtitleydatayinyayselectedylanguageyisynotybroadcast,ytheydefaultylanguageysubtitleywillybeydisplayed. Exit SoftwareyUpdate PictureyTest 2 SoundyTest SignalyTest ZoomyOut Close Product/ServiceyInfo. NetworkyTest UseryGuide Close UseryGuide 3 2 Toyuseyinputydevice ToyuseyEnergyySavingyfeature PROGRAMMEySetting Toysetytimeyoptions PICTURE,ySOUNDySetting OPTION ToysetyTVylockyoptions Toysetylanguage AdvabcedyFunction Toysetycountry Information 1 Toysetysubtitle 1 Allowsytoyselectytheycategoryyyouywant. 2 Allowsytoyselectytheyitemyyouywant. Youycanyusey ytoymoveybetweenypages. H 3 Allowsytoybrowseytheydescriptionyofythey functionyyouywantyfromytheyindex. 1 Showsytheydescriptionyofytheyselectedymenu. ytoymoveybetweenypages. Youycanyusey H 2 Zoomsyinyoryoutytheyscreen. MAINTENANCE / TROUBLESHOOTING 25 Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION yy Make sure to turn the power off and disconnect the power cord and all other cables first. yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges.y Screen, frame, cabinet and stand yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth. yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth. CAUTION yy Avoid touching the screen at all times, as this may result in damage to the screen. yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in scratches and image distortions. yy Do not use any chemicals as this may damage the product. yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.y Power cord Remove the accumulated dust or dirt on the power cord regularly. TROUBLESHOOTING Problem Solution Cannot control the TV with the remote control. yy Check the remote control sensor on the product and try again. yy Check if there is any obstacle between the product and the remote control. yy Check if the batteries are still working and properly installed ( to , to ). No image display and no sound is produced. yy Check if the product is turned on. yy Check if the power cord is connected to a wall outlet. yy Check if there is a problem in the wall outlet by connecting other products. The TV turns off suddenly. yy Check the power control settings. The power supply may be interrupted. yy Check if the Auto sleep feature is activated in the Time settings. yy If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity. When connecting to the PC (RGB/ HDMI DVI), ‘No signal’ or ‘Invalid Format’ is displayed. yy Turn the TV off/on using the remote control. yy Reconnect the RGB/HDMI cable. yy Restart the PC with the TV on. ENGLISH ENG MAINTENANCE 26 SPECIFICATIONS ENGLISH ENG SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. 32CS56** MODELS Dimensions (W x H x D) Weight With stand (mm) Without stand (mm) 795.0 x 504.0 x 73.5 9.2 With stand (kg) Without stand (kg) Power requirement MODELS Dimensions (W x H x D) Weight 32CS560-TD 32CS560Y-TD 795.0 x 568.0 x 207.0 With stand (mm) 8.1 Power requirement 42CS56** 42CS560-TD 42CS560Y-TD 1019.0 x 698.0 x 265.0 913.0 x 571.0 x 77.4 1019.0 x 631.0 x 76.5 12.8 15.1 11.1 13.4 AC 100-240 V~ 50 / 60 AC 100-240 V~ 50 / 60 AC 100-240 V~ 50 / 60 Hz Hz Hz 47CS56** 47CS560-TD 47CS560Y-TD 1132.0 x 762.0 x 265.0 Without stand (mm) 1132.0 x 695.0 x 76.5 19.0 With stand (kg) Without stand (kg) 37CS56** 37CS560-TD 37CS560Y-TD 913.0 x 639.0 x 265.0 17.3 AC 100-240 V~ 50 / 60 Hz SPECIFICATIONS New Zealand, Singapore Operating temperature 0 °C to 40 °C Operating humidity Less than 80 % Storage temperature -20 °C to 60 °C Storage humidity Less than 85 % Television System Programme Coverage Australia Television System Programme Coverage Indonesia, Israel, Myanmar, Sri Lanka Television System Programme Coverage Vietnam, Malaysia Television System Programme Coverage Iran, Algeria, Tunisia, Digital model Television System Programme Coverage Analogue model, India, Thailand, South Africa, -- Television System Programme Coverage External Antenna Impedance Digital TV Analogue TV DVB-T PAL/SECAM-B/G/D/K, PAL-I UHF 21 to 69 DVB-T VHF 06 to 12, UHF 27 to 69 DVB-T UHF 21 to 69 DVB-T VHF 6 to 12, UHF 21 to 69 DVB-T VHF 5 to 12, UHF 21 to 69 BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 PAL B/B B/B : VHF/UHF 0 to 75, CATV : 2 to 44 PAL/SECAM-B/G/D/K, PAL-I, NTSC-M BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 PAL/SECAM-B/G/D/K, PAL-I, NTSC-M BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 PAL/SECAM-B/G/D/K, PAL-I, NTSC-M BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 - PAL/SECAM-B/G/D/K, PAL-I, NTSC-M - BG : VHF/UHF 1 to 69, CATV 01 to 47 I : VHF/UHF 1 to 69, CATV 01 to 47 DK : VHF/UHF 1 to 69, CATV 01 to 47 M : VHF/UHF 2 to 78, CATV 01 to 71 75 Ω 75 Ω ENGLISH ENG Environment condition 27 28 SPECIFICATIONS ENGLISH ENG HDMI/DVI-DTV supported mode Horizontal Frequency (kHz) Vertical Frequency (Hz) 31.469 31.5 59.94 60 720x576 31.25 50 1280x720 37.5 44.96 45 50 59.94 60 33.72 33.75 28.125 26.97 27 33.716 33.75 56.25 67.43 67.5 59.94 60 50 23.97 24 29.976 30.00 50 59.94 60 Resolution 720x480 1920x1080 Component port connecting information Component ports on the TV Y PB PR Video output ports on DVD player Y PB PR Y B-Y R-Y Y Cb Cr Y Pb Pr Signal Component 480i/576i O 480p/576p O 720p/1080i O 1080p O (50 Hz / 60 Hz only) For any Suggestion, Opinion, Complaints, Please Call 800 54 in UAE 0800 54 54 54 in South Africa 080 100 54 54 in Morocco 19960 in Egypt Other countries, Please contact our local dealer or log into http://www.lg.com Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. MODEL SERIAL (Only DTV)
advertising