LG | 50PM6900 | LG 50PM6900 Owner’s Manual

OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating your set and retain it
for future reference.
50PM6900
60PM6900
P/NO : MFL67468634 (1205-REV00)
www.lg.com
2
LICENSES
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays
DivX video. Visit divx.com for more information and software tools to convert your
files into DivX video.
ENGLISH
ENG
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to
vod.divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation
or its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274”
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol
& DTS and the Symbol together are registered trademarks & DTS 2.0+Digital
Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights
Reserved.
IMPORTANT SAFETY INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance
of your product.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
Clean only with a dry cloth.
yy
Do not block any ventilation openings. Install
yy
in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such
yy
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
Do not defeat the safety purpose of the
yy
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet (Can differ by country).
ENG
ENGLISH
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of
electric shock to persons.
Do not use this apparatus near water.
yy
4
IMPORTANT SAFETY INSTRUCTIONS
Protect the power cord from being walked on
yy
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
Only use attachments/accessories specified
yy
by the manufacturer.
Use only with a cart, stand, tripod, bracket,
yy
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
ENGLISH
ENG
Unplug this apparatus during lightning
yy
storms or when unused for long periods of
time.
Short-circuit
Breaker
Short-circuit
Breaker
Short-circuit
Breaker
Short-circuit
Breaker
Refer all servicing to qualified service
yy
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Short-circuit
Breaker
Keep the packing anti-moisture material or
yy
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach of
children.
CAUTION concerning the Power Cord
yy
(Can differ by country):
It is recommended that appliances be
placed upon a dedicated circuit; that is, a
single outlet circuit which powers only that
appliance and has no additional outlets or
branch circuits. Check the specification page
of this owner’s manual to be certain. Do not
connect too many appliances to the same
AC power outlet as this could result in fire or
electric shock. Do not overload wall outlets.
Overloaded wall outlets, loose or damaged
Power
Supply
wall
outlets, extension cords, frayed power
Power Supply
cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could
result in electric shock or fire. Periodically
examine the cord of your appliance, and
Power
if Supply
its appearance indicates damage or
deterioration,
unplug it, discontinue use of
Power Supply
the appliance, and have the cord replaced
with an exact replacement part by an
authorized service. Protect the power cord
from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where
Power
Supply
the
cord exits the appliance. Do not move
the TV with the power cord plugged in. Do
not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the
power cord. Do not pull on the power cord
to unplug the TV.
Do not stick metal objects or any other
yy
conductive material into the power cord. Do
not touch the end of the power cord while it
is plugged in.
Short-circuit
Power Supply
IMPORTANT SAFETY INSTRUCTIONS
Warning - To reduce the risk of fire or
yy
electrical shock, do not expose this product
to rain, moisture or other liquids. Do not
touch the TV with wet hands. Do not install
this product near flammable objects such
as gasoline or candles, or expose the TV to
direct air conditioning.
Do not expose to dripping or splashing and
yy
do not place objects filled with liquids, such
as vases, cups, etc. on or over the apparatus
(e.g. on shelves above the unit).
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
As long as this unit is connected to the AC
yy
wall outlet, it is not disconnected from the
AC power source even if the unit is turned
off.
Do not attempt to modify this product in any
yy
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this
product.
ANTENNAS Outdoor antenna grounding
yy
(Can differ by country):
If an outdoor antenna is installed, follow
the precautions below. An outdoor antenna
system should not be located in the vicinity
of overhead power lines or other electric light
or power circuits, or where it can come in
contact with such power lines or circuits as
death or serious injury can occur. Be sure the
antenna system is grounded so as to provide
some protection against voltage surges
and built-up static charges. Section 810 of
the National Electrical Code (NEC) in the
U.S.A. provides information with respect to
proper grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Power Supply
DISCONNECTING DEVICE FROM THE MAIN
yy
POWER
Mains plug is the disconnecting device.
The plug must remain readily operable.
Antenna Lead in Wire
Ground Clamp
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamp
NEC: National Electrical Code
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
ENG
ENGLISH
Grounding
yy
(Except for devices which are not grounded.)
Ensure that you connect the earth
Power ground
Supply
Short-circuit
wire to prevent possible
electric shock
Breaker
(i.e. a TV with a three-prong grounded AC
plug must be connected to a three-prong
grounded AC outlet). If grounding methods
are not possible, have a qualified electrician
install a separate circuit breaker. Do not try to
ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.
5
6
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
ENG
Cleaning
yy
When cleaning, unplug the power cord and
wipe gently with a soft cloth to prevent
scratching. Do not spray water or other
liquids directly on the TV as electric shock
may occur. Do not clean with chemicals
such as alcohol, thinners or benzine.
Moving
yy
Make sure the product is turned off,
unplugged and all cables have been
removed. It may take 2 or more people to
carry larger TVs. Do not press or put stress
on the front panel of the TV.
Ventilation
yy
Install your TV where there is proper
ventilation. Do not install in a confined
space such as a bookcase. Do not cover the
product with cloth or other materials while
plugged. Do not install in excessively dusty
places.
If you smell smoke or other odors coming
yy
from the TV, unplug the power cord and
contact an authorized service center.
Do not press strongly upon the panel with a
yy
Supply
hand or a sharp objectShort-circuit
such as aPower
nail,
pencil
Breaker
or pen, or make a scratch on it.
Keep the product away from direct sunlight.
yy
Never touch this apparatus or antenna during
yy
a thunder or lightning storm.
When mounting a TV on the wall, make sure
yy
not to install the TV by hanging the power
and signal cables on the back of the TV.
Do not allow an impact shock or any objects
yy
to fall into the product, and do not drop
anything onto the screen.
Dot Defect
yy
The Plasma or LCD panel is a high
technology product with resolution of two
million to six million pixels. In a very few
cases, you could see fine dots on the screen
while you’re viewing the TV. Those dots
are deactivated pixels and do not affect the
performance and reliability of the TV.
Generated Sound
yy
“Cracking” noise: A cracking noise that
occurs when watching or turning off the TV
is generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a highspeed switching circuit, which supplies a
large amount of current to operate a product.
It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
Take care not to touch the ventilation
yy
openings. When watching the TV for a long
period, the ventilation openings may become
hot. This does not affect the performance of
the product or cause defects in the product.
Preventing “Image burn” or “Burn-in” on your TV screen
If a fixed image displays on the TV screen for
yy
a long period of time, it will be imprinted and
become a permanent disfigurement on the
screen. This is “image burn” or “burn-in” and
not covered by the warranty.
If the aspect ratio of the TV is set to 4:3 for a
yy
long period of time, image burn may occur on
the letterboxed area of the screen.
Avoid displaying a fixed image on the TV screen
yy
for a long period of time (2 or more hours for
LCD, 1 or more hours for the Plasma TV) to
prevent image burn.
IMPORTANT SAFETY INSTRUCTIONS
7
Viewing 3D Imaging (For 3D models)
WARNING
Viewing Environment
Viewing Time
yy
- When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a long
period of time may cause headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or chronic illness
Some users may experience a seizure or other abnormal symptoms when they are exposed to a
yy
flashing light or particular pattern from 3D contents.
Do not watch 3D videos if you feel nausea, are pregnant and/ or have a chronic illness such as
yy
epilepsy, cardiac disorder, or blood pressure disease, etc.
3D Contents are not recommended to those who suffer from stereo blindness or stereo anomaly.
yy
Double images or discomfort in viewing may be experienced.
If you have strabismus (cross-eyed), amblyopia (weak eyesight) or astigmatism, you may have trouble
yy
sensing depth and easily feel fatigue due to double images. It is advised to take frequent breaks than
the average adult.
If your eyesight varies between your right and left eye, revise your eyesight prior to watching 3D
yy
contents.
Do not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking.
yy
When these symptoms are experienced, stop using/watching 3D contents and get enough rest until
yy
the symptom subsides.
- Consult your doctor when the symptoms persist. Symptoms may include headache, eyeball pain,
dizziness, nausea, palpitation, blurriness, discomfort, double image, visual inconvenience or fatigue.
ENG
ENGLISH
Symptoms which require discontinuation or refraining from watching 3D contents
8
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
Viewing Environment
Viewing Distance
yy
- Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If you
feel discomfort in viewing 3D contents, move further away from the TV.
Viewing Position (Only for SG Mode)
yy
- Face the center of the screen at eye level with the head looking straight ahead. Otherwise, you may
not be able to view 3D contents properly.
Viewing Age
ENGLISH
ENG
Infants / Children
yy
- Usage/ Viewing 3D contents for children under the age of 5 are prohibited.
- Children under the age of 10 may overreact and become overly excited because their vision is in
development (for example: trying to touch the screen or trying to jump into it. Special monitoring and
extra attention is required for children watching 3D contents.
- Children have greater binocular disparity of 3D presentations than adults because the distance
between the eyes is shorter than one of adults. Therefore they will perceive more stereoscopic depth
compared to adults for the same 3D image.
Teenagers
yy
- Teenagers under the age of 19 may be stimulated to light coming from 3D videos. Advise them not to
watch 3D videos for a long time when they are tired.
Elderly
yy
- The elderly may perceive less of a 3D effect than the youth. Do not sit closer to the TV than the
recommended distance.
Cautions when using the 3D glasses
Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly.
yy
Do not use 3D glasses instead of your normal glasses, sunglasses or protective goggles.
yy
Using modified 3D glasses may cause eye strain or image distortion.
yy
Do not keep your 3D glasses in extremely high or low temperatures. It will cause deformation.
yy
The 3D glasses are fragile and are easy to be scratched. Always use a soft, clean piece of cloth when
yy
wiping the lenses. Do not scratch the lenses of the 3D glasses with sharp objects or clean/wipe them
with chemicals.
When watching 3D videos under fluorescent lights or with three wave length lamps, you may
yy
experience the screen blinking. When this occurs, turn the light off or turn it down. (Only for SG
mode)
Other electronic or communication devices should be turned off or put away from the TV because it
yy
can cause interference and prevent the 3D function from working properly. (Only for SG mode)
When you watch TV lying down, 3D images may look darker or invisible. (Only for SG mode)
yy
TABLE OF CONTENTS
9
TABLE OF CONTENTS
2
LICENSES
3
IMPORTANT SAFETY INSTRUCTIONS
7
Viewing 3D Imaging (For 3D models)
9
TABLE OF CONTENTS
34 Pentouch
10
Installation Procedure
34
35
35
10
ASSEMBLING AND PREPARING
10
12
13
14
15
15
16
16
17
18
Unpacking
Optional Extras
Parts and buttons
Lifting and moving the TV
Setting up the TV
-Attaching the stand
-Attaching the protection cover
-Tidying cables
-Mounting on a table
-Mounting on a wall
19
MAKING CONNECTIONS
19
20
Connecting to an antenna or cable
Connecting to a HD receiver, DVD, or VCR
player
-HDMI Connection
-DVI to HDMI Connection
-Component Connection
-Composite Connection
Connecting to a PC
-HDMI Connection, DVI to HDMI
Connection or RGB Connection
Connecting to an Audio System
-Digital Optical Audio Connection
Connecting to a USB
26
26
27
28 REMOTE CONTROL
30
31
31
31
Magic Remote Control Functions
-Registering Magic Remote Control
-How to use Magic Remote Control
-Precautions to Take when Using the
Magic Remote Control
WATCHING TV
32
Turning the TV on for the first time
33 Using the user guide
Using Pentouch
-Using the Pentouch Function
-Pairing between Touch Pen
38 TROUBLESHOOTING
39
OPEN SOURCE SOFTWARE NOTICE
39
EXTERNAL CONTROL DEVICE SETUP
40 SPECIFICATIONS
43 MAINTENANCE
43
43
43
Cleaning Your TV
-Screen, frame, cabinet and stand
-Power cord
NOTE
Image shown may differ from your TV.
yy
Your TV’s OSD (On Screen Display) may
yy
differ slightly from that shown in this manual.
The available menus and options may differ
yy
from the input source or product model that
you are using.
New features may be added to this TV in the
yy
future.
ENG
ENGLISH
20
21
22
23
24
24
32
10
ASSEMBLING AND PREPARING
Installation Procedure
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
4 Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
ASSEMBLING AND PREPARING
Unpacking
ENGLISH
ENG
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
7
8
9
0
FLASHBK
LIST
6
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Remote control,
Batteries (AAA)
(See p.28)
Magic Remote Control,
Batteries (AA)
(See p.30)
Owner’s manual
Power Cord
Cable holder
(See p.16)
Power Cord holder
(See p.16)
ASSEMBLING AND PREPARING
11
Stand Screws
3 EA, M5 x 16
(See p.15)
Protection cover
(See p.16)
Eye-bolt & Wall bracket
2 EA
(See p.17)
Cradle
(See p.35)
Charging Cable
(Depending on model)
(See p.37)
Stand Body
(See p.15)
Stand Base
(See p.15)
Tip
The number of tip may differ
depending on the model.
(See p.37)
Touch
Home
Touch Pen
The number of touch pen may
differ depending on the model.
(See p.35)
ENG
ENGLISH
Stand Screws
4 EA, M4 x 30
(See p.15, p.16)
12
ASSEMBLING AND PREPARING
Optional Extras
Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
Touch
Home
AG-S3**
3D Glasses
The model name or
design may be changed
manufacturer’s circumstances
or policaies.
AN-MR300
Magic Remote Control
AN-TP300
Touch Pen, Cradle
The number of touch pen and
tip may differ depending on
the model.
ENGLISH
ENG
AN-VC***
Video Call Camera
The model name or
design may be changed
manufacturer’s circumstances
or policaies.
(Depending on model)
NOTE
The items supplied with your product may vary depending on the model.
yy
Product specifications or contents of this manual may be changed without prior notice due to
yy
upgrade of product functions.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved items are not covered by the warranty.
yy
In case of some model, the thin film on screen is a part of TV, So don’t take it off.
yy
ASSEMBLING AND PREPARING
13
Parts and buttons
Screen
Remote control and
intelligent1 sensors
Power indicator
Speakers
INPUT SETTINGS
OK
Buttons
Description
/I
Turns the power on or off.
INPUT
Changes the input source.
SETTINGS
Accesses the main menus, or saves your input and exits the menus.
OK ⊙
Selects the highlighted menu option or confirms an input.
-
Adjusts the volume level.
+
v ^
Scrolls through the saved channels.
1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
ENG
ENGLISH
Button
14
ASSEMBLING AND PREPARING
Lifting and moving the TV
When moving or lifting the TV, read the following
to prevent the TV from being scratched or
damaged and for safe transportation regardless of
its type and size.
When transporting a large TV, there should
yy
be at least 2 people.
When transporting the TV by hand, hold the
yy
TV as shown in the following illustration.
Caution
Avoid touching the screen at all times, as
yy
this may result in damage to the screen.
It is recommended to move the TV in the
yy
box or packing material that the TV originally
came in.
Before moving or lifting the TV, disconnect
yy
the power cord and all cables.
When holding the TV, the screen should face
yy
away from you to avoid damage.
ENGLISH
ENG
Hold the top and bottom of the TV frame
yy
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
When transporting the TV, do not expose the
yy
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
yy
upright, never turn the TV on its side or tilt
towards the left or right.
ASSEMBLING AND PREPARING
15
Setting up the TV
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
If you are not mounting the TV to a wall, use the following instructions to attach the stand.
1
3 EA
M5 x 16
Stand Body
Front
Stand Base
2
3
4 EA
M4 x 30
Caution
Make sure that the screws are fastened
yy
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.)
Do not fasten the screws with too much
yy
force; otherwise they may be worn out
and get loosened.
ENG
ENGLISH
Caution
When attaching the stand to the TV
yy
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
16
ASSEMBLING AND PREPARING
Attaching the protection cover
Tidying cables
1 Remove the stand before installing the TV
1 Install the power cord holder and power cord.
on a wall mount by performing the stand
attachment in reverse.
After removing the stand, push the supplied
protection cover into the opening at the bottom
of the TV until it locks in place.
This will protect the opening from accumulating
dust and dirt.
It will help prevent the power cable from being
removed by accident.
Power cord holder
2 Gather and bind the cables with the cable
holder.
Protection cover
2 Secure the TV and the protection cover with
the 2 screws.
ENGLISH
ENG
Cable holder
Caution
Do not move the TV by holding the cable
yy
holder and power cord holder, as the cable
holders may break, and injuries and damage
to the TV may occur.
2 EA
M4 x 30
Caution
Make sure that the screws are fastened
yy
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.)
Do not fasten the screws with too much
yy
force; otherwise they may be worn out
and get loosened.
ASSEMBLING AND PREPARING
Mounting on a table
17
Securing the TV to a wall
1 Lift and tilt the TV into its upright position on a
table.
-Leave a 10 cm (4 inch) (minimum) space from
the wall for proper ventilation.
10 cm (4 inch)
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
1 Insert and tighten the eye-bolts on the back of
the TV.
Do not place the TV near or on sources
yy
of heat, as this may result in fire or other
damage.
-If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Adjusting the angle of the TV to suit view
Swivel 20 degrees to the left or right and adjust
the angle of the TV to suit your view.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
20
20
Caution
Make sure that children do not climb on or
yy
hang on the TV.
Note
Caution
When adjusting the angle of the TV, watch
yy
out for your fingers.
- Personal injury may occur if hands or fingers
are pinched. If the product is tilted too
much, it may fall, causing damage or injury.
se a platform or cabinet that is strong and
U
yy
large enough to support the TV securely.
ENG
ENGLISH
Caution
18
ASSEMBLING AND PREPARING
Mounting on a wall
Caution
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm (4 inch)
10 cm
Disconnect the power first, and then move
yy
or install the TV. Otherwise electric shock
may occur.
If you install the TV on a ceiling or slanted
yy
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and contact
the local dealer or qualified personnel.
Do not over tighten the screws as this may
yy
cause damage to the TV and void your
warranty.
Use the screws and wall mounts that meet
yy
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
10 cm
Note
10 cm
ENGLISH
ENG
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described
in the following table.
Model
50PM6900
60PM6900
VESA
Standard screw
Number of screws
Wall mount
bracket (optional)
400 x 400
M6
4
PSW400B,
PSW400BG
600 x 400
M8
4
PSW600B,
PSW600BG
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The wall mount bracket is optional. You can
yy
obtain additional accessories from your local
dealer.
The length of screws may differ depending
yy
on the wall mount. Make sure to use the
proper length.
For more information, refer to the manual
yy
supplied with the wall mount.
MAKING CONNECTIONS
19
MAKING CONNECTIONS
Connect various external devices to the TV and switch input modes to select an external device. For more
information on external device’s connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC,
gaming devices, and other external devices.
NOTE
If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable
yy
to the TV through a DVD recorder or VCR. For more information on recording, refer to the manual
provided with the connected device.
The external device connection may differ from the model.
yy
Connect external devices to the TV regardless of the order of the TV port.
yy
If you connect a gaming device to the TV, use the cable supplied with the gaming device.
yy
Refer to the external equipment’s manual for operating instructions.
yy
Connecting to an antenna or cable
Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may
differ from the actual items and a RF cable is optional.
UHF Antenna
Antenna
ANTENNA/
CABLE IN
Coaxial (75Ω)
Terminal
Caution
Make sure not to bend the copper wire of
yy
the RF cable.
Copper wire
Complete all connections between devices,
yy
and then connect the power cord to the
power outlet to prevent damage to your TV.
NOTE
Use a signal splitter to use more than 2 TVs.
yy
Visit http://lgknowledgebase.com for more
yy
information about the antenna and cable
connection. Search for antenna.
ENG
ENGLISH
VHF Antenna
20
MAKING CONNECTIONS
Connecting to a HD receiver, DVD, or VCR player
Connect a HD receiver, DVD, or VCR player to the TV and select an appropriate input mode.
HDMI Connection
HDMI is the best way to connect a device.
Transmits the digital video and audio signals from an external device to the TV. Connect the external device
and the TV with the HDMI cable as shown in the following illustration.
NOTE
Choose any HDMI IN input port to connect.
It does not matter which port you use.
ENGLISH
ENG
IN 1(ARC)
/ DVI IN 2
Use the latest High Speed HDMI™ Cable with CEC (Customer Electronics Control) function.
yy
High Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher.
yy
HDMI
(*Not Provided)
DVD / Blu-Ray / HD Cable Box / HD STB
IN
3
4
NOTE
DTV Audio Supported Codec: MPEG, Dolby
yy
Digital
HDMI Audio Supporeted Format: Dolby
yy
Digital, PCM (Up to 192 KHz, 32k/44.1k/48k/
88k/96k/176k/192k) -> Not supported DTS.
ARC (Audio Return Channel)
When connected with a high-speed
yy
HDMI cable, digital audio can be sent
to a compactible device without an
additional optical audio cable.
ARC is only supported on the HDMI
yy
input 1 (ARC) port. An external audio
device that supports ARC should be
connected to HDMI 1 if you wish to
use ARC.
MAKING CONNECTIONS
21
DVI to HDMI Connection
/DVI IN 2
Transmits the digital video signal from an external device to the TV. Connect the external device and the
TV with the DVI-HDMI cable as shown in the following illustration. To transmit an audio signal, connect an
audio cable.
DVI OUT
(*Not Provided)
(*Not Provided)
AUDIO OUT
AUDIO
AUDIOININ
(RGB/DVI)
DVD / Blu-Ray / HD Cable Box
ENG
ENGLISH
22
MAKING CONNECTIONS
Component Connection
Transmits the analog video and audio signals from an external device to the TV. Connect the external
device and the TV with the component cable as shown in the following illustration.
NOTE
If cables are installed incorrectly, it could cause the image to display in black and white or with
yy
distorted color.
Check to ensure the cables are matched with the corresponding color connection.
yy
AV IN
ENGLISH
ENG
COMPONENT IN
VIDEO
L/MONO AUDIO R
2
Y
PB
PR
L
R
1
AUDIO
VIDEO
RED
WHITE
RED
BLUE
GREEN
(*Not Provided)
(*Not Provided)
VIDEO
RED
WHITE
RED
BLUE
GREEN
L
R
AUDIO
DVD / Blu-Ray / HD Cable Box
MAKING CONNECTIONS
23
Composite Connection
Transmits the analog video and audio signals from an external device to the TV. Connect the external
device and the TV with the composite cable as shown in the following illustration.
NOTE
yyIf you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the TV.
AV IN
L/MONO AUDIO R
2
PB
PR
L
R
RED
Y
WHITE
1
YELLOW
ENG
ENGLISH
COMPONENT IN
VIDEO
(*Not Provided)
RED
WHITE
YELLOW
VIDEO
L (MONO) AUDIO R
VCR / DVD / Blu-Ray / HD Cable Box
24
MAKING CONNECTIONS
Connecting to a PC
NOTE
It is recommended to use the TV with the HDMI connection for the best image quality.
yy
Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.
yy
In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or
yy
brightness. If noise is present, change the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
The synchronization input form for Horizontal and Vertical frequencies is separate.
yy
Depending on the graphics card, some resolution settings may not allow the image to be positioned
yy
on the screen properly.
HDMI Connection, DVI to HDMI Connection or RGB Connection
Choose method A, B, or C to make connection.
IN 1(ARC)
/ DVI IN 2
Choose any HDMI input port to connect.
It does not matter which port you use.
HDMI
(*Not Provided)
PC
4
3
㶌⸬ (ARC)
IN
/DVI IN 2
ENGLISH
ENG
Method A: HDMI Connection
AUDIO IN
(RGB/DVI)
IN
3
IN
4
MAKING CONNECTIONS
4
3
25
/DVI IN 2
/DVI IN 2
㶌⸬ (ARC)
㶌⸬ (ARC)
Method B: DVI to HDMI Connection
(*Not Provided)
AUDIO IN
(RGB/DVI)
AUDIO IN
(RGB/DVI)
(*Not Provided)
$8',2287
'9,287
$8',2287
Method C: RGB Connection
RGB IN
(PC)
AUDIO IN
RGB IN
(PC)
(RGB/DVI)
AUDIO IN
(RGB/DVI)
(*Not Provided)
(*Not Provided)
$8',2287
5*%2873&
$8',2287
5*%2873&
PC
ENG
ENGLISH
PC
'9,287
26
MAKING CONNECTIONS
Connecting to an Audio System
You may use an optional external audio system instead of the built-in speaker.
NOTE
If you use an optional external audio device instead of the built-in speaker, set the TV speaker feature
yy
to off.
Digital Optical Audio Connection
Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV
with the optical audio cable as shown in the following illustration.
NOTE
Do not look into the optical output port. Looking at the laser beam may damage your vision.
yy
Audio with ACP (Audio Copy Protection) function may block digital audio output.
yy
ENGLISH
ENG
OPTICAL
DIGITAL
AUDIO OUT
(*Not Provided)
OPTICAL AUDIO IN
Digital Audio System
MAKING CONNECTIONS
27
Connecting to a USB
Connect a USB storage device such as a USB flash memory, external hard drive, or a USB memory card
reader to the TV and access the Smart Share menu to use various multimedia files.
NOTE
To store apps on a USB storage device, make sure that it is connected to the USB IN 1 port.
yy
To use a USB Hub device, make sure that it is connected to the USB IN 1 port.
yy
(*Not Provided)
USB Hub
USB IN 1 / USB Apps USB IN 2
Choose any USB input port to connect.
It does not matter which port you use.
USB
or
ENG
ENGLISH
28
REMOTE CONTROL
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching
the and ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
Caution
BACK may damage
HOME
Do not mix old and new batteries, as this
the remote control.
yy
Make sure to point the remote control toward at the remote control sensor on the TV.
VOL
RATIO
INPUT
(User-Guide)
My APPS
Sees
User-Guide.
TV
ENGLISH
ENG
1
2
3
4
5
6
7
8
9
0
FLASHBK
LIST
RATIO
Resizes an image.
INPUT
Changes the input source; Turns the TV on.
TV
CH
MUTE
Q.MENU
SETTINGS
HOME
MY APPS
OK
AV MODE EXIT
ENERGY
SAVING
INFO
REC
Returns to the last TV channel.
REC
FAV
VOL
CH
(POWER)
Turns the TV on or off.
P
A
G
E
Number button
Enters numbers.
LIST, - (Dash)
LIST: Accesses the saved channel list.
- (Dash): Inserts a dash between numbers such as 2-1 and 2-2.
FLASHBK
Alternates between the two last channels selected (pressing
repeatedly).
REMOTE CONTROL
29
+ VOL Adjusts the volume level.
FAV
Accesses your favorite channel list.
RATIO
INPUT
3D
TV
Used for viewing 3D video.
1
2
3
MUTE
Mutes all sounds.
4
5
6
7
8
9
^ CH v, PAGE
CH: Scrolls through the saved channels.
RECMoves
REC to the previous or next screen.
PAGE:
REC
0
FLASHBK
LIST
SETTINGS
Accesses the main menu.
FAV
VOL
CH
MUTE
Q.MENU
HOME
MY APPS
OK
MY
REC APPS
Shows the list of Apps.
Q. MENU
Accesses the quick menu.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
OK
Selects menus or options and confirms your input.
(BACK)
Returns to the previous level.
AV MODE EXIT
AV MODEREC
Selects an AV mode.
REC
EXIT
Clears all on-screen displays and returns to TV viewing.
ENERGY
SAVING
INFO
REC
Color buttons
These access special functions in some menus.
Control buttons
Controls the Premium contents, Smart Share menus, or the
SIMPLINK compatible devices (USB,SIMPLINK).
Accesses the AV devices connected to the TV;
Opens the SIMPLINK menu.
REC
ENERGY SAVING
Adjusts the brightness of the screen to reduce energy
consumption.
INFO
Views the information of the current program and screen.
REC
REC
ENG
ENGLISH
SETTINGS
HOME REC
Accesses the HOME menu.
P
A
G
E
30
REMOTE CONTROL
Magic Remote Control Functions
When the message “Magic remote control battery is low. Change the battery.” is
displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching
and ends to the label inside the compartment, and close the battery cover. Be
sure to point the remote control at the remote control sensor on the TV.
To remove the batteries, perform the installation actions in reverse.
Caution
Do not mix old and new batteries, as this may damage the remote control.
yy
yyDo not need Magic remote Dongle to operate the magic remote control. The Receiver is built into the TV.
Make sure to point the remote control at the remote control sensor on the TV.
Pointer (RF & Bluetooth transmitter)
Blinks the light when operating.
(POWER)
Turns the TV on or off.
BACK
BACKlevel.
Returns to the previous
HOME
ENGLISH
ENG
Wheel (OK)
Selects menus or options and confirms
your input;
Scrolls through the saved channels.
If you press the navigation button while
moving the pointer on the screen,
the pointer disappears, and the Magic
remote control works as aVOL
regular
remote control.
To display the pointer again, shake the
Magic remote control from side to side.
BACK
BACK
VOL
CH
VOL
1
TV
11-1 Brief Info Title Test...
3
ꘄ
VOL
the Home menu.
HOME
HOME
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
+ VOL Adjusts the volume level.
^ CH v
CH
Scrolls through the saved channels.
CH
(MUTE)
CH
Mutes all sounds.
MY APPS
Shows the list of Apps.
Q. MENU
Accesses the quick menu.
My APPS
My APPS
3D
Uses for viewing 3D video.
11:40 AM
HOME
Accesses
BACK
HOME
My APPS
My APPS
2
1
If you press the Wheel (OK) button on the Magic
remote control, the following screen appears.
Shows information about the current program
and screen.
2
If you press the Wheel (OK) button on the Magic
remote control, the following screen appears.
Set the channel you want.
You can press the CH button on the remote
control to set the channel.
3
You can select My apps Menu.
i Info.
REMOTE CONTROL
Registering Magic Remote Control
The Magic remote Control operates by pairing with
your TV. Once you purchased the TV, please
register the Magic remote control as follows;
How
the Magic Remote Control
BACK to register
HOME
To register the remote control, press
the Wheel (OK) button on the remote
control.
How
the Magic Remote Control
VOL to Re-register
CH
after Registration Failure
My APPS
BACK
BACK
BACK
HOME
HOME
VOL
CH
How to use
My APPS Magic Remote
Control
My APPS
My APPS
My APPS
VOL
1 If the pointer disappears, move
the remote control slightly to left
or right. Then, it will automatically
appear on the screen.
»»If the pointer has not been used
for a certain period of time, it
will disappear.
2 You can move the pointer by
aiming the Pointer Receiver of
the remote control at your TV
then move it left, right, up or
down.
»»If the pointer does not work
properly after clicking the
Wheel (OK) button, leave
the remote control for 10
seconds then use it again.
Precautions to Take when Using
the Magic Remote Control
Use the remote control within the maximum
yy
communication distance (10 m, 32.8ft).
Using the remote control beyond this
distance, or with an object obstructing it,
may cause a communication failure.
A communication failure may occur due to
yy
nearby devices. Electrical devices such as
a microwave oven or wireless LAN product
may cause interference, as these use the
same bandwidth (2.4 GHz) as the Magic
Remote Control.
The Magic Remote Control may be damaged
yy
or may malfunction if it is dropped or
receives a heavy impact.
Take care not to bump into nearby furniture
yy
or other people when using the Magic
Remote Control.
Manufacturer and installer cannot provide
yy
service related to human safety as the
applicable wireless device has possibility of
HOME
electric wave interference.
It is recommended that an Access Point (AP)
yy
be located more than 1 m (3.28 ft) away
from the TV. If the AP is installed closer than
1 m (3.28 ft), the magic remote control may
not perform as expected due to frequency
CH
interference.
My APPS
ENG
ENGLISH
VOL
1 Press and hold the BACK
and
BACKfor 5 HOME
buttons together
BACKseconds
HOME
to reset, then register it
by following “How to register the
Magic remote control” above. (Once
the reset is complete, the light on
the Pointer blinks.)
2 To re-register the Magic remote
control, press and hold the BACK
button for 5 seconds toward the BACK
TV.
VOL
CH
CH(Once the reset is complete, the
VOL
CH
light on the Pointer blinks.)
HOME
HOME
31
32
WATCHING TV
WATCHING TV
Turning the TV on for the first
time
When you turn the TV on for the first time, the
Initial setting screen appears. Select a language
and customize the basic settings.
NOTE
Select Home* when prompted.
yy
Store* mode puts the TV in demo mode.
If you select Store*, the any customized
yy
settings will switch back to the default
settings of Store* in 5 minutes.
1 Connect the power cord to a power outlet.
2 In Standby mode, press the power button on
the remote control to turn the TV on.
The Initial setting screen appears if you turn
the TV on for the first time.
4 When the basic settings are complete,
BACK
HOME
press OK or
VOL
(Wheel).
NOTE
CH
My APPS
NOTE
You can also access Initial Setting by
yy
accessing OPTION in the main menu.
3 Follow the on-screen instructions to customize
ENGLISH
ENG
your TV settings according to your preferences.
Language Selection
Selects a language to
display.

Using the Magic remote Sets the Magic remote
contol.
control

Using the Touch Pen
Sets the Touch Pen.

Enviroment Selection
Select Home* for the
home environment.

Time Zone Setting

Network Connection

Auto Tuning
Selects the time zone
and daylight saving.
(Depending on country)
Sets your network to
enable network-related
features on the TV.
Scans and saves available
channels automatically.

Setting is completed.
Confirms the setting
options.
If you do not complete the Initial setting,
yy
it will appear whenever the TV turns on.
Disconnect the power cord from the
yy
power outlet when you do not use the
TV for a long period of time.
5 To turn the TV off, press the power button on
the remote control.
Using the User guide
33
Using the user guide
User Guide allows you to more easily access the
detailed TV information.
1
1 Press the HOME button to access the HOME
menu.
2 Select User Guide and press the Wheel (OK)
button.
3
2
Input List
Settings
Live TV
Search
Internet
3D
LG Smart W
TV Guide
User Guide
Ch. List

3
User Guide
4
1
Shows the description of the selected menu.
You can use ꕌ/ꕍ to move between pages.
2
Moves to the selected menu directly from
the User Guide.
3
Zooms in or out the screen.
3
To use input device
To use Energy Saving feature
CHANNEL Setting
To set time options
PICTURE,SOUND setting
To set TV lock options
OPTION
To set language
LG Smart Function
To set Magic remote control
Advanced Function
Information
To set other options
2
1
Shows the current channel.
2
Allows to select the category you want.
3
Allows to select the item you want.
You can use ꕌ/ꕍ to move between pages.
4
Allows to browse the description of the
function you want from the index.
ENG
ENGLISH
User Guide
1
34
PENTOUCH
Pentouch
Using Pentouch
Pentouch allows you to use touch pen supported
features like Sketchbook, My Gallery, Office
Viewer, Internet, Smart Home and PC Link.
warning
ENGLISH
ENG
Do not drop or throw the touch pen and
yy
cradle. Do not swing the touch pen and
cradle with the charging cable connected
to it. This can damage the product or cause
personal injury.
For people using pacemakers, the distance
yy
between the touch pen and the pacemaker
should be at least 30 cm. Never use it
where wireless communication is prohibited.
Protect it from extreme vibrations or
magnetic objects. Wireless communications
can cause malfunctions or failures.
Do not use or store the touch pen and cradle
yy
in direct sunlight, near a hot object (e.g.,
a heater or fireplace), or in dusty or highhumidity environments. This can result in
product deformation, malfunction, failure, or
fire.
If abnormal sound, smoke, or odor is
yy
detected, immediately remove the charging
cable and stop using the product. Contact a
service center. This can cause failures or fire.
If fluid leaks from the touch pen and cradle,
yy
do not touch the fluid with bare hands.
If fluid comes into contact with eyes,
immediately rinse eyes with abundant tap
water, then consult a doctor. The fluid can
cause blindness. If the fluid comes into
contact with skin or clothing, immediately
wash it off with tap water. If the fluid causes
skin inflammation or injury, consult a doctor.
Do not allow the fluid to come into contact
yy
with fire. Do not heat the product in a
microwave or convection oven.
Use the specified USB cable when charging
yy
the battery.
Keep the touch pen and cradle out of reach
yy
of children and away from unstable locations.
Do not let children or pets put the touch pen
and cradle in their mouths or lick the touch
pen and cradle. Playing with or swallowing it
may cause serious injury.
Do not use the touch pen and cradle with
yy
wet hands. Do not let foreign substances
(e.g., soft drinks or water) enter the touch
pen and cradle; if this happens, do not use
the touch pen and cradle. Do not touch
the optic receiver of the touch pen and
cradle with a sharp object. This can result in
electrical shock or damage the product.
Do not use the product under extreme
yy
temperature conditions. Do not use the
product immediately after going from the
cold outdoors to the warm indoors. This
can cause condensation in the pen. This
can result in damaging the product. Turn
off the power and wait several hours until
the moisture evaporates before using the
product.
Never disassemble or modify the touch
yy
pen and cradle. The product warranty does
not cover damage or injury caused by
unauthorized disassembly. This can result in
electrical shock or damage the product.
If fluid leaks from the touch pen and cradle,
yy
the use of fire in the vicinity is strictly
prohibited. The leaked fluid or gas can is
flammable.
Avoid extreme shocks or impacts to the
yy
product, for example, placing a heavy object
on it or pressing it.
Do not display fixed characters or images
yy
on the screen for extended periods of time.
This can cause image sticking.
Do not connect the charging cable to
yy
peripheral devices or disks that are not
specified. This can cause malfunctions or
failures.
Do not leave the touch pen and cradle on
yy
the floor. Stepping on it can damage the
product or cause personal injury.
Be careful when disposing of the product.
yy
The touch pen and cradle consists of a
lithium-polymer battery and plastic material.
Burning can be dangerous, so dispose of it
according to local regulations.
Do not remove the charging cable using
yy
excessive force. This could damage the
charging port and PC.
Do not handle the touch pen and cradle with
yy
excessive force. If you use the touch pen
and cradle with excessive force, you may
leave foreign substances on the screen.
Clean the product with the product cleaning
cloth provided.
When multiple people use the touch pen
yy
and cradle, make sure that sufficient space
is available. Collisions can cause injury or
failures.
PENTOUCH
Using the Pentouch Function
35
Touch Pen
1
2
3
h
Touc e
Hom
Multiple functions are available on the TV using
the pen.
Before using the Pentouch functions, please
follow the steps below.
1 Pair the pen with the TV.
4
2 Run the Pentouch program on the TV.
3 Use the TV's help menu for details of the
No.
Pentouch functions.
1
2
3
4
Pairing between Touch Pen
Description
Power button / LED indicator
USB charging port
Touch Home button
Touch pen tip switch
What is Pairing?
Cradle
ENG
ENGLISH
You need to pair the touch pen before using the
touch pen.
Once paired, you do not need to pair them again
unless you:
Bought a new pen
yy
Replaced the old pen with a new one
yy
Attempt to pair a new touch pen for using
yy
two pens simultaneously
USB charging port
Things to Know Before Pairing
This program allows pairing of up to two
yy
pens.
In order to pair two pens, perform one by
yy
one.
Pairing is not possible if a paired pen is
yy
currently in use.
If you pair a new touch pen when two pens
yy
have already been paired, all the previous
pairing data is deleted.
Pairing
To
H uc
om h
e
Note
Touch pens and cradles are sold separately
yy
at dealers.
When you leave your touch pen unused for
yy
a certain period of time (8 minutes), the pen
automatically powers off.
36
PENTOUCH
Pairing for the First Time
Caution When Unpairing
1 Place the pen within 10 cm from the LG logo
1 Be careful not to unpair the pen by mistake. If
2 Press the
2 If you unpair and pair a normally functioning
at the bottom of the TV.
(POWER) button on the touch pen
once.
3 The LED indicator on the touch pen will red
for 2 seconds and blinks green 3 times when
pairing is complete.
4 If the LED indicator is red for 4 - 5 seconds and
blinks red 3 times, pairing is not successful.
Please try pairing again.
5 Once a pen is paired, the red LED blinks once
when you press the Touch Home button.
Unpairing (Resetting the touch pen)
1 Press the Touch Home button on the touch
ENGLISH
ENG
pen and check that the red LED blinks once.
2 Press the Touch Home button and the
(POWER) button together, regardless of
sequence, for more than 4 seconds.
3 If you release the buttons after 4 seconds, the
pen will be reset. The red LED will blink three
times and the pen will be turned off.
unpaired, try pairing it again.
touch pen, the other paired pen may not work.
In this case, unpair the nonfunctioning touch
pen and pair it again by following the steps
described in the Pairing for the First Time
section.
Touch pen Operation
Once paired, you can use the touch pen in the
following ways.
1 Powering on
-Press the (POWER) button once. The red
and green LEDs will remain lit to indicate that
the power is on.
2 Powering off
-Press the (POWER) button for more than 3
seconds and release it. The red LED will blink
3 times and the pen will be turned off.
3 Return to Touch Home by pressing the
Touch Home button while using the touch pen.
* When a menu is displayed on the screen, the
Touch Home button does not work.
Close the menu and then press the Touch
Home button.
PENTOUCH
Tip replacement
37
Note
1 Detach the tip holder and the tip to be replaced
from the pen.
Tip Holder
Tip
2 Insert a new tip into the detached tip holder
and assemble the tip holder with the pen.
Tip
Charging the touch pen
Charging on the cradle
yy
or
Charging directly
yy
or
To
Homuc
e
h
ENG
ENGLISH
Tip Holder
After an hour and 30 minutes of a continuous
yy
charge, you can use the touch pen for about
2 hours.
Do not use Pentouch while charging.
yy
Green LED will be turned on during using
yy
touch pen. If you don’t use touch pen, it will
be automatically turned off after 8 minutes.
Touch pen LED indicator for battery status
yy
- Charging: Red LED
- Charging complete: Green LED
- No battery power: Red LED blinks every
second and powers off automatically.
- LED ON Sleep mode: If no switch (tip switch,
function key, power key) is pressed for 10
seconds, the device enters sleep mode but
the LED stays green.
- LED OFF Sleep mode: If there is no input
for one minute after entering LED ON Sleep
mode, the LED is turned off and the device
enters LED OFF Sleep mode.
- Power off mode: The device is powered off if
there is no input for 8 minutes.
If the cradle is connected to the TV, the pen
yy
can be charged when the TV is switched on
or is on standby.
If the pen is connected directly to the TV
yy
through the charging cable, the pen cannot
be charged when the TV is on standby.
ch
Tou me
Ho
38
TROUBLESHOOTING
TROUBLESHOOTING
General
Problem
Solution
Cannot control the TV with the
remote control.
yyCheck the remote control sensor on the product and try again.
yyCheck if there is any obstacle between the product and the remote control.
to ).
yyCheck if the batteries are still working and properly installed ( to ,
No image display and no sound is
produced.
yyCheck if the product is turned on.
yyCheck if the power cord is connected to a wall outlet.
yyCheck if there is a problem in the wall outlet by connecting other products.
The TV turns off suddenly.
yyCheck the power control settings. The power supply may be interrupted.
yyCheck if the Auto sleep feature is activated in the Time settings.
yyIf there is no signal while the TV is on, the TV will turn off automatically after
15 minutes of inactivity.
When connecting to the PC (RGB/
HDMI DVI), ‘No Signal’ or ‘Invalid
Format’ is displayed.
yyTurn the TV off/on.
yyReconnect the RGB/HDMI cable.
yyRestart the PC with the TV on.
ENGLISH
ENG
Pentouch
Problem
Solution
The touch pen does not work.
yyPress the (POWER) button on the touch pen to check that it is powered on.
yyCheck that the touch pen is paired for use. (The touch pen is correctly paired if
the red LED is on once when you press the Touch Home button on the touch
pen.)
The touch pen works on and off.
yyCheck if the touch pen is fully charged. (When it needs to be charged, the red
LED blinks every two seconds.)
yyUnpair the touch pen and pair it again before using it.
OPEN SOURCE SOFTWARE NOTICE
39
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com .
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
To obtain the external control device setup information, please visit www.lg.com.
40
SPECIFICATIONS
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
Power requirement
AC100 - 240 V ~ 50/60 Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
75 Ω
Environment
condition
Operating
Temperature
0 - 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 - 60 °C
Storage Humidity
Less than 85 %
50PM6900
(50PM6900-UD)
MODELS
Dimensions
(W x H x D)
ENGLISH
ENG
Weight
With stand
1168.0 mm x 758.0 mm x 297.0 mm 1386.8 mm x 883.2 mm x 354.7 mm
(45.9 inch x 29.8 inch x 11.6 inch)
(54.5 inch x 34.7 inch x 13.9 inch)
Without stand
1168.0 mm x 704.0 mm x 53.0 mm
(45.9 inch x 27.7 inch x 2.0 inch)
1386.8 mm x 818.2 mm x 53.0 mm
(54.5 inch x 32.2 inch x 2.0 inch)
With stand
28.8 kg (63.4 lbs)
40.6 kg (89.5 lbs)
Without stand
26.4 kg (58.2 lbs)
36.4 kg (80.2 lbs)
3.2 A / 320 W
4.6 A / 460 W
Current Value / Power consumption
HDMI/DVI-DTV supported mode
Component port connecting information
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x480
31.469
31.5
59.94
60
1280x720
44.96
45
59.94
60
33.72
33.75
26.97
27
33.716
33.75
67.43
67.5
59.94
60
23.97
24
29.976
30.00
59.94
60
1920x1080
60PM6900
(60PM6900-UD)
Component ports
on the TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i
O
480p
O
720p/1080i
O
1080p
O
(60 Hz only)
SPECIFICATIONS
41
3D supported mode
yyMedia contents and a player need to support HDMI 3D Frame Packing, HDMI 3D Side by Side, HDMI 3D
Top & Bottom to play in 3D.
yyVideo, which is input as HDMI,USB,DLNA, is switched into the 3D screen automatically. (This function
does not support all of the 3D video format. The specific 3D video format is not switched into the 3D screen
automatically.)
yy2D -> 3D mode is available to watch for all signals.
yyFor models supporting WiDi, you can set the 3D mode in the same way as in RGB (PC) mode.
Input
Signal
Resolution
480p
640X480
720X480
640X480
720X480
720p
HDMI-DTV
1080i
1280X720
1920X1080
1080p
Component
USB
DLNA
DTV
62.938 / 63
Playable 3D video format
Frame packing, Line alternative
59.94/ 60
31.469 / 31.5
89.91/90
59.94 / 60
44.96 / 45
59.94 / 60
67.432 / 67.5
59.94 / 60
33.72 / 33.75
59.94 / 60
53.946 / 54
67.432/67.5
26.97 / 27
33.716 / 33.75
23.97 / 24
29.976 / 30
23.97 / 24
29.976 / 30.00
Side-by-side (Full), Top-and-Bottom,
Side-by-side (half)
Frame packing, Line alternative
Side-by-side (Full), Top-and-Bottom
Side-by-side(half), Single Frame
Sequential
Frame packing, Field alternative
Side-by-side(Full), Top-and-Bottom,
Side-by-side(half)
Frame packing, Line alternative
Side-by-side(Full), Top-and-Bottom,
Side-by-side(half), Checkerboard
Top-and-Bottom, Side-by-side(half),
Checkerboard, Single Frame
Sequential, Row Interleaving,
Column Interleaving
Side by Side (Half), Top & Bottom
67.43 / 67.5
59.94 / 60
1024X768
48.363
60.004
1360X768
47.712
60.015
1920X1080
67.50
60.00
1024X768
48.363
60.004
Side by Side (Half), Top & Bottom
Side by Side (Half), Top & Bottom,
Checkerboard, Single Frame Sequential
Row Interleaving, Column Interleaving
Side by Side (Half), Top & Bottom
1360X768
47.712
60.015
Side by Side (Half), Top & Bottom
1920X1080
67.50
60.00
Side by Side (Half), Top & Bottom
44.96 / 45
33.72 / 33.75
59.94 / 60
59.94 / 60
Side by Side, Top & Bottom
30
Side by Side, Top & Bottom,
Checker Board, Single Frame Sequential,
Row Interleaving, Column Interleaving,
MPO (Photo), JPS (Photo)
(Photo : Side by Side(half), Top & Bottom)
30
Side by Side, Top & Bottom,
Checker Board, Single Frame Sequential,
Row Interleaving, Column Interleaving,
MPO (Photo), JPS (Photo)
(Photo : Side by Side(half), Top & Bottom)
HDMI-PC
RGB-PC
Vertical
Frequency (Hz)
720p
1080i
1080p
1080p
1280X720
1920X1080
1920X1080
1920X1080
33.75
33.75
Signal
Playable 3D video format
720p, 1080i
Side by Side, Top & Bottom
ENG
ENGLISH
1920X1080
Horizontal
Frequency (kHz)
42
SPECIFICATIONS
Wireless LAN module (WN8122E) specification
This device only works with compatible LG TV.
Pentouch Dongle (AN-TD200) specification
Frequency Range
2400 ~ 2483.5 MHz
Standard
IEEE802.11a/b/g/n
Modulation
GFSK
Frequency Range
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz
Output Power (Max.) 0 dBm
Receive sensitivity
- 82 dBm
Modulation
CCK / OFDM / MIMO
Data rate (Max.)
2 Mbps
802.11a: 14 dBm
802.11b: 17 dBm
Output Power (Typical) 802.11g: 15 dBm
802.11n - 2.4GHz: 13.5 dBm
802.11n - 5GHz: 12 dBm
Data rate
802.11a/g: 54 Mbps
802.11b: 11 Mbps
802.11n: 300 Mbps
Antenna Gain (Typical)
2400 to 2483.5 MHz: -0.79 dBi
5150 to 5250 MHz: 0.62 dBi
5725 to 5850 MHz: 0.52 dBi
Occupied bandwidth
802.11a/b/g: HT20
802.11n: HT20/40
ENGLISH
ENG
Because band channel used by the country could
be different, the user can not change or adjust the
operating frequency and this product is set for the
regional frequency table.
Bluetooth module (BM-LDS302) specification
Standard
Bluetooth Version 3.0
Frequency Range
2400 ~ 2483.5 MHz
Output Power (Max.) 10 dBm or lower
Data rate (Max.)
3 Mbps
Communication
Line of Open Sight approx. 10 m
Distance
MAINTENANCE
43
MAINTENANCE
Cleaning Your TV
Clean your TV regularly to keep the best
performance and to extend the product lifespan.
Caution
Make sure to turn the power off and
yy
disconnect the power cord and all other
cables first.
When the TV is left unattended and unused
yy
for a long time, disconnect the power cord
from the wall outlet to prevent possible
damage from lightning or power surges.
Screen, frame, cabinet and stand
Caution
Do not push, rub, or hit the surface with
yy
your fingernail or a sharp object, as this may
result in scratches on the screen and image
distortions.
Do not use any chemicals, such as waxes,
yy
benzene, alcohol, thinners, insecticides, air
fresheners, lubricants, as these may damage
the screen’s finish and cause discoloration.
Do not spray liquid onto the surface. If water
yy
enters the TV, it may result in fire, electric
shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the
power cord regularly.
ENG
ENGLISH
To remove dust or light dirt, wipe the surface with
a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a
soft cloth dampened in clean water or a diluted
mild detergent. Then wipe immediately with a dry
cloth.
The model and serial number of the TV is
located on the back and/or one side of the TV.
Record it below should you ever need service.
MODEL
SERIAL
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating your set and retain it
for future reference.
www.lg.com
2
EXTERNAL CONTROL DEVICE SETUP
IR CODES
(Depending on model)
How to Connect
Connect your wired remote control to the Remote Control port on the TV.
Remote Control IR Codes
Output waveform
Single pulse, modulated with 37.917kHz signal at 455kHz
Tc
T1
Frame configuration
ENGLISH
ENG
1st frame
Lead code
Low custom code
High custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
Repeat frame
Repeat code
Tf
Lead code
9 ms
4.5 ms
Repeat code
0.55 ms
9 ms
2.25 ms
Bit description
Bit “0”
Bit “1”
0.56 ms
0.56 ms
2.24 ms
1.12 ms
Frame interval: Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
EXTERNAL CONTROL DEVICE SETUP
Code
(Hexa)
Function
(POWER)
Note
Code
(Hexa)
Function
0F
DC
3D
Remote control Button
42
Q.MENU/MY APPS Remote control Button
5B
EXIT
Remote control Button
43
SETTINGS
Remote control Button
7C
HOME
Remote control Button
7A
0B
INPUT
Remote control Button
10 - 19
Number Key 0-9
Remote control Button
4C
- (Dash)/LIST
Remote control Button
1A
FLASHBK
Remote control Button
09
MUTE
Remote control Button
02
VOL +
Remote control Button
03
VOL -
Remote control Button
00
CH ^
Remote control Button
01
CH v
Remote control Button
1E
Remote control Button
^
Remote control Button
41
v
Remote control Button
07
<
Remote control Button
06
>
Remote control Button
44
OK
Remote control Button
28
79
BA
(BACK)
RATIO
REC
Remote control Button
(User-Guide)
Remote control Button
D6
TV
Discrete IR Code
(TV Input Selection)
C4
POWER ON
Discrete IR Code
(Only Power Off)
C5
POWER OFF
Discrete IR Code
(Only Power Off)
5A
AV
Discrete IR Code
(AV Input Selection)
BF
COMPONENT1
Discrete IR Code
(Component1 Input
Selection)
D4
COMPONENT2
Discrete IR Code
(Component2 Input
Selection)
D5
RGB-PC
Discrete IR Code
(RGB-PC Input Selection)
CE
HDMI1
Discrete IR Code
(HDMI1 Input Selection)
CC
HDMI2
Discrete IR Code
(HDMI2 Input Selection)
E9
HDMI3
Discrete IR Code
(HDMI3 Input Selection)
DA
HDMI4
Discrete IR Code
(HDMI4 Input Selection)
76
Ratio 4:3
Discrete IR Code
(Only 4:3 Mode)
77
Ratio 16:9
Discrete IR Code
(Only 16:9 Mode)
AF
Ratio Cinema
Zoom
Discrete IR Code
(Only Cinema Zoom Mode)
Remote control Button
Remote control Button
yy (FREEZE)
Remote control Button
95
ENERGY SAVING
Remote control Button
7E
SIMPLINK
Remote control Button
AA
INFO
Remote control Button
30
AV MODE
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
B1
n
Remote control Button
B0

Remote control Button
BA
yy
Remote control Button
8E

Remote control Button
8F

Remote control Button
Use the feature depending on your model.
yy
ENG
ENGLISH
FAV/MARK
40
TV
Note
Remote control Button
(Power On/Off)
08
3
4
EXTERNAL CONTROL DEVICE SETUP
EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup
Connect the RS-232C (serial port) input jack to
an external control device (such as a computer or
an A/V control system) to control the product’s
functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Type of connector;
D-Sub 9-Pin Male
1
Note
RS-232C on this TV is intended to be used
yy
with third party RS-232C control hardware
and software. The instructions below
are provided to help with programming
software or to test functionality using telenet
software. RS-232C connection cables are not
supplied with the product.
5
6
9
RS-232C IN
(CONTROL & SERVICE)
No.
Pin name
ENGLISH
ENG
1
No connection
2
RXD (Receive data)
3
TXD (Transmit data)
4
DTR (DTE side ready)
5
GND
6
DSR (DCE side ready)
7
RTS (Ready to send)
8
CTS (Clear to send)
9
No Connection
EXTERNAL CONTROL DEVICE SETUP
RS-232C configurations
Set ID
Set ID number.
7-Wire Configuration
(Serial female-female NULL modem cable)
PC
RXD
X
OPTION
TV
2
3
• Language
TXD
• Caption
: Off
• ISM Method
: Normal
TXD
3
2
RXD
GND
5
5
GND
DTR
4
6
DSR
DSR
6
4
DTR
RTS
7
8
CTS
1 Press SETTINGS to access the main menu.
CTS
8
7
RTS
2 Press the Navigation buttons to scroll to
D-Sub 9
5
• Pointer
• Balloon Help : On
• Initial Setting
• Set ID
:1
?
SETUP and press OK.
D-Sub 9
3 Press the Navigation buttons to scroll to
option and press OK.
3-Wire Configurations(Not standard)
4 Press the Navigation buttons to scroll to Set ID
3
TXD
TXD
3
2
RXD
GND
5
5
GND
DTR
4
6
DSR
DSR
6
4
DTR
RTS
7
8
CTS
CTS
8
7
RTS
D-Sub 9
D-Sub 9
and press OK.
5 Scroll left or right to select a set ID number and
select close. The adjustment range is 1-99.
6 When you are finished, press EXIT.
*Real data mapping
0 : Step 0
…
2
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
ENG
ENGLISH
RXD
…
TV
…
PC
6
EXTERNAL CONTROL DEVICE SETUP
Communication Parameters
Stop bit: 1 bit
yy
Communication code: ASCII code
yy
Use a crossed (reverse) cable.
yy
Baud rate: 9600 bps (UART)
yy
Data length: 8 bits
yy
Parity : None
yy
Command reference list
01. Power
COMMAND1
COMMAND2
DATA
(Hexadecimal)
k
a
00 - 01
COMMAND1
COMMAND2
DATA
(Hexadecimal)
14. Balance
k
t
00 - 64
x
t
(See p.9)
ENGLISH
ENG
02. Input Select x
b
(See p.8)
15. 3D (For 3D
TV)
03. Aspect
Ratio
k
c
(See p.8)
16. Color
Temperature
x
u
00 - 64
04. Screen
Mute
k
d
00 - 01
17.Extended
3D (For 3D TV)
x
v
(See p.9)
05. Volume
Mute
k
e
00 - 01
18. ISM
Method
j
p
(See p.9)
06. Volume
Control
k
f
00 - 64
19. Energy
Saving
j
q
(See p.9)
07. Contrast
k
g
00 - 64
20. Auto
Configuration
j
u
(See p.10)
08. Brightness
k
h
00 - 64
22. Channel
Add/Del
m
b
00 - 01
09. Color
k
i
00 - 64
23. Key
m
c
(See p.10)
10. Tint
k
j
00 - 64
11. Sharpness
k
k
00 - 32
12. OSD Select k
l
00 - 01
13. Remote
Control Lock
Mode
m
00 - 01
21. Channel
Tuning
k
COMMAND1 COMMAND2
DATA00
DATA01
DATA02
DATA03
DATA04
DATA05
(Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal)
m
physical
program
high
a
major
program
low
major low
minor high minor low
attribute
EXTERNAL CONTROL DEVICE SETUP
7
Transmission / Receiving protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
[Set ID] :You can adjust the set ID to choose desired set ID number in Option menu. Adjustment range is
1~ 99. When selecting Set ID ‘0’, every connected the set is controlled. Set ID is indicated as decimal (1~
99) on menu and as Hexa decimal (0x0~ 0x63) on transmission /receiving protocol.
[DATA] : To transmit the command data.
Transmit the ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
* In this model, set will not send the status during the standby mode.
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from nonviable functions or communication errors.
Data01: Illegal Code
Data02: Not supported function
Data03: Wait more time
* In this model, set will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[NG] : Use the large character
ENG
ENGLISH
The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
* In this model, set will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[OK] : Use the large character.
8
EXTERNAL CONTROL DEVICE SETUP
01. Power (Command: k a)
To control Power On/Off of the set.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 00: Power Off Data 01: Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* In a like manner, if other functions transmit ‘FF’
data based on this format, Acknowledgement data
feedback presents status about each function.
* Note: In this model, set will send the Acknowledge
after power on processing completion.
There might be a time delay between command and
acknowledge.
06. Volume Control (Command: k f)
To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
07. Contrast (Command: k g)
To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
02. Input Select (Command: x b)
To select input source for set.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 00: DTV (Antenna) Data 01: DTV (Cable)
Data 10: Analog (Antenna)
Data 11: Analog (Cable)
Data 20: AV or AV1 Data 21: AV2
Data 40: Component1
Data 41: Component2
Data 42: Component3
Data 60: RGB-PC
Data 90: HDMI1 Data 91: HDMI2
Data 92: HDMI3 Data 93: HDMI4
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
* Use the feature depending on your model.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01: 4:3 Data 09: Just scan
Data 02: 16:9 Data 10: Cinema Zoom 1
Data 04: Zoom
Data 06: Set by program Data 1F: Cinema Zoom16
…
ENGLISH
ENG
03. Aspect Ratio (Command: k c)
To adjust the screen format.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
04. Screen Mute (Command: k d)
To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00: Screen mute off (Picture on), Video-out Mute off
Data 01: Screen mute on (Picture off)
Data 10: Video-out Mute on
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of Video-out Mute on only, TV will display On
Screen Display (OSD). But, in case of screen mute on,
TV will not display On Screen Display (OSD).
05. Volume Mute (Command: k e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00: Volume mute on (Volume off)
Data 01: Volume mute off (Volume on)
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
08. Brightness (Command: k h)
To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
09. Color (Command: k i)
To adjust screen color.
You can also adjust color in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
10. Tint (Command: k j)
To adjust screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red: 00 ~ Green: 64 (*transmit by Hexadecimal
code)
*Refer to “Real data mapping”.
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
11. Sharpness (Command: k k)
To adjust screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 32 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
12. OSD Select (Command: k l)
To select OSD (On Screen Display) on/off.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00: OSD off Data 01: OSD on
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
13. Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel controls
on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off
Data 01: Lock on
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
If you’re not using the remote control and front panel
controls on the Monitor set, use this mode. When main
power is on/off, remote control lock is released.
If Key Lock is on in the standby mode, TV will not turn on
by POWER button of remote control and on the TV.
14. Balance (Command: k t)
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
15. 3D (Command: x t) (For 3D TV)
To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][Cr]
Data1
00: 3D On
01: 3D Off
02: 3D to 2D
03: 2D to 3D
Data2
00: Top and Bottom
01: Side by Side
02: Check Board
03: Single Frame Sequential
04: Column interleaving 05: Row interleaving
Data3
00: Right to Left
01: Left to Right
Data4
3D Depth: Min : 00 ~ Max : 14
(*transmit by Hexadecimal code)
*If data1 is 01(3D Off) , data2 , data3 , data4 have no
meaning.
*If data1 is 02(3D to 2D), data2, data3 and data4 have no
meaning.
*I f data1 is 03(2D to 3D), data2 and data3 have no
meaning.
Data 01
00
01
02
03
Data 02
o
x
x
x
Data 03
o
x
x
x
Data 04
x
x
x
o
x : Don’t care
Acknowledgement [t][ ][OK][Data01][Data02]
[Data03][Data04][x][t][ ][NG][Data01][x]
16. Color Temperature (Command: x u)
To adjust color temperature.
You can also adjust color temperature in the PICTURE
menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to “Real data mapping”.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
17. Extended 3D (Command: x v) (For 3D TV)
To change 3D option for TV. Use the feature depending
on your model.
Transmission [x][v][ ][Set ID][ ][Data01][ ][Data02][Cr]
Data1: 3D option
00: 3D Picture Correction
01: 3D Depth
02: 3D Viewpoint
07: 3D Sound Zooming
08: Normal Image View
09: 3D Mode
Data2: It has own range for each 3D option determined
by Data1.
1) When Data1 is 00
00: Right to Left
01: Left to Right
2) When Data1 is 01
Data Min: 00 ~ Max: 14 (*transmit by Hexadecimal code)
3) When Data1 is 02
Data Min: 00 ~ Max: 14 (*transmit by Hexadecimal code)
4) When Data1 is 07
00: Off 01: On
5) When Data1 is 08
00: Off 01: On
6) When Data1 is 09
00: Standard 01: Sports
02: Cinema 03: Extreme
04: Manual
Acknowledgement [v][ ][OK][Data01][Data02][x]
[v][ ][NG][Data01][x]
* Use the feature depending on your model.
18. ISM Method (Command: j p)
To avoid having a fixed image remain on screen.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data 02: Orbiter
08: Normal
20: Color Wash
Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
19. Energy Saving (Command: j q)
To control the energy saving function.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Data 00: off
ENG
ENGLISH
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
9
10
EXTERNAL CONTROL DEVICE SETUP
01: Minimum
02: Medium
03: Maximum
04: Intelligent Sensor
05: Screen off
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
20. Auto Configuration (Command: j u)
To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
21. Channel Tuning (Command: m a)
To tune channel to following physical/major/minor
number.
(This feature is not available for all models.)
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
ENGLISH
ENG
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that the
channel should be mapped to, and the Minor is the subchannel. Since the ATSC tuner automatically maps the
channel to the Major number, the Physical number is not
required when sending a command.
Data 00: Physical Channel Number
NTSC air: 02~45, NTSC cable: 01, 0E~7D
ATSC air: 01~45, ATSC cable: 01~87
Data 01 & 02: Major Channel Number
Data 01: High byte Data 02: Low byte
Two bytes are available for the Major and Minor,
normally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.
The table lists the binary code which must be converted
to Hexadecimal before sending. For example:
The binary code to tune the sub source to an NTSC cable
channel is “1000 0001”, which translates to “81” in
Hex.
* 7th bit : For which source do you want to change
the channel.
* 6th bit: Use a two part or one part channel. Most
cases just use 0 since it’s ignored when using
NTSC.
* 5th bit: Use 0 with NTSC since it can only use
the physical channel number. Normally use 1 for
ATSC since most times it doesn’t matter what the
physical number is.
* 4th bit: Set to 0.
* 3-0 bits: Choose signal type.
* Tune Command Examples:
1. Tune to the analog (NTSC) cable channel 35.
Data 00 = Physical of 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = 0000 0001 in binary = 01
Total = ma 00 23 00 00 00 00 01
2. Tune to the digital (ATSC) local channel 30-3.
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = 0010 0010 in binary = 22
Total = ma 00 00 00 1E 00 03 22
22. Channel Add/Del (Command: m b)
To add and delete the channels.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Channel Delete Data 01: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
23. Key (Command: m c)
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
See page 3.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
When TV is in the standby mode, TV will turn on by
POWER button of remote control only.
EXTERNAL CONTROL DEVICE SETUP
11
* Table List (Channel Tuning)
7
Main/Sub
Picture
6
Two/One
Part
Channel
5
Using
Physical
Channel
4
Reserved
3
2
1
0
Step
0
Main
0
Two
0
Use
x
0
0
0
0
NTSC Air
1
Sub
1
One
1
No Use
x
0
0
0
1
NTSC Cable
x
0
0
1
0
ATSC Air
x
0
0
1
1
ATSC Cable_std
x
0
1
0
0
ATSC Cable_hrc
x
0
1
0
1
ATSC Cable_irc
x
0
1
1
0
ATSC cable_auto
x
0
1
1
1
Reserved
x
x
x
x
x
...
x
1
1
1
1
Reserved
ENG
ENGLISH
Download PDF