LG | 65EG960T-TA | LG 55EG920T Owner’s Manual

THE ULTIMATE DISPLAY
OWNER’S MANUAL
Please read this manual carefully before operating your set and retain
it for future reference.
EG96**
EG92**
EG91**
*MFL68927403*
www.lg.com
P/NO : MFL68927403 (1510-REV04)
Printed in Korea
2
TABLE OF CONTENTS
ENGLISH
ENG
TABLE OF CONTENTS
3LICENSES
33
MAGIC REMOTE FUNCTIONS
3
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
35
35
35
- Registering magic remote
- How to use magic remote
- Precautions to take when using the magic
remote
4
SAFETY INSTRUCTIONS
36
USING THE USER GUIDE
10
- Viewing 3D Imaging (Only 3D models)
12
INSTALLATION PROCEDURE
12
ASSEMBLING AND PREPARING
12Unpacking
14
Separate purchase
15
Parts and buttons
16
- Using the joystick button
17
Lifting and moving the TV
18
Setting up the TV
18
- Attaching the stand
23
Mounting on a table
24
Mounting on a wall
25
Tidying cables
26
36MAINTENANCE
36
36
36
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
37TROUBLESHOOTING
37
EXTERNAL CONTROL DEVICE SETUP
38SPECIFICATIONS
MAKING CONNECTIONS
26
Antenna connection
27
HDMI connection
28
DVI to HDMI connection
29
Component connection
30
Composite connection
30
Audio connection
30
- Digital optical audio connection
31Headphone connection
31
USB connection
WARNING
yy If you ignore the warning message, you may
be seriously injured or there is a possibility
of accident or death.
CAUTION
yy If you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
yy The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE INFORMATION
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
OPEN SOURCE SOFTWARE NOTICE INFORMATION
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
ENGLISH
ENG
LICENSES
4
SAFETY INSTRUCTIONS
ENGLISH
ENG
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before
using the product.
WARNING
Do not place the TV and/or remote control in the
following environments:
• A location exposed to direct sunlight
• An area with high humidity such as a bathroom
• Near any heat source such as stoves and other
devices that produce heat
• Near kitchen counters or humidifiers where they
can easily be exposed to steam or oil
• An area exposed to rain or wind
• Near containers of water such as vases
Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
Make sure to connect Mains cable to compliant
AC mains socket with Grounded earth pin. (Except
for devices which are not grounded on earth.)
Otherwise possibility you may be electrocuted or
injured.
Insert power cable plug completely into wall socket
otherwise if not secured completely into socket, fire
ignition may break out.
Ensure the power cord does not come into contact
with hot objects such as a heater. This may cause a
fire or an electric shock hazard.
Do not place the product where it might be exposed
to dust. This may cause a fire hazard.
Do not place a heavy object, or the product itself, on
power cables.
Otherwise, this may result in fire or electric shock.
Mains Plug is the TV connecting/disconnecting
device to AC mains electric supply.This plug must
remain readily attached and operable when TV is
in use.
Bend antenna cable between inside and outside
building to prevent rain from flowing in. This may
cause water damaged inside the Product and could
give an electric shock.
Do not touch the power plug with wet hands.
Additionally, if the cord pin is wet or covered
with dust, dry the power plug completely or wipe
dust off. You may be electrocuted due to excess
moisture.
When mounting TV onto wall make sure to neatly
install and isolate cabling from rear of TV as to not
create possibility of electric shock /fire hazard.
SAFETY INSTRUCTIONS
5
ENGLISH
ENG
Do not plug too many electrical devices into a single
multiple electrical outlet. Otherwise, this may result
in fire due to over-heating.
Do not insert any metal objects/conductors (like
a metal chopstick/cutlery/screwdriver) between
power cable plug and input Wall Socket while it
is connected to the input terminal on the wall.
Additionally, do not touch the power cable right
after plugging into the wall input terminal. You may
be electrocuted. (Depending on model)
Do not drop the product or let it fall over when
connecting external devices. Otherwise, this may
result in injury or damage to the product.
Des
icca
nt
Keep the anti-moisture packing material or vinyl
packing out of the reach of children. Anti-moisture
material is harmful if swallowed. If swallowed
by mistake, force the patient to vomit and visit
the nearest hospital. Additionally, vinyl packing
can cause suffocation. Keep it out of the reach of
children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause
serious injury.
Dispose of used batteries carefully to ensure that
a small child does not consume them. Please seek
Doctor- Medical Attention immediately if child
consumes batteries.
Do not put or store inflammable substances near
the product. There is a danger of combustion/
explosion or fire due to careless handling of the
inflammable substances.
Do not drop metallic objects such as coins, hair pins,
chopsticks or wire into the product, or inflammable
objects such as paper and matches. Children must
pay particular attention. Electrical shock, fire or
injury can occur. If a foreign object is dropped into
the product, unplug the power cord and contact the
service centre.
Do not spray water on the product or scrub with an
inflammable substance (thinner or benzene). Fire or
electric shock accident can occur.
Do not allow any impact, shock or any objects to
fall into the unit, and do not drop anything onto the
screen. You may be injured or the product can be
damaged.
6
SAFETY INSTRUCTIONS
ENGLISH
ENG
Never touch this product or antenna during a
thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage
of gas, open the windows and ventilate. It may
cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at
your own discretion. Fire or electric shock accident
can occur.
Contact the service centre for check, calibration or
repair.
If any of the following occur, unplug the product
immediately and contact your local service centre.
• The product has been impacted by shock
• The product has been damaged
• Foreign objects have entered the product
• The product produced smoke or a strange smell
This may result in fire or electric shock.
Unplug the TV from AC mains wall socket if you
do not intend to use the TV for a long period of
time. Accumulated dust can cause fire hazard and
insulation deterioration can cause electric leakage/
shock/fire.
Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be
exposed to oil or oil mist. This may damage the
product and cause it to fall.
If water enters or comes into contact with TV,
AC adapter or power cord please disconnect the
power cord and contact service centre immediately.
Otherwise ,this may result in electric shock or fire.
Only use an authorized AC adapter and power cord
approved by LG Electronics. Otherwise, this may
result in fire, electric shock, malfunction or product
deformation.
Never Disassemble the AC adapter or power cord.
This may result in fire or electric shock.
Be careful in handling the adapter to prevent any
external shocks to it.
An external shock may cause damage to the adapter.
SAFETY INSTRUCTIONS
7
Install the product where no radio wave occurs.
There should be enough distance between an
outside antenna and power lines to keep the former
from touching the latter even when the antenna
falls. This may cause an electric shock.
Do not install the product on places such as unstable
shelves or inclined surfaces. Also avoid places where
there is vibration or where the product cannot be
fully supported. Otherwise, the product may fall or
flip over, which may cause injury or damage to the
product.
ENGLISH
ENG
CAUTION
When installing the antenna, consult with a qualified
service technician. If not installed by a qualified
technician, this may create a fire hazard or an electric
shock hazard.
We recommend that you maintain a distance of at
least 2 to 7 times the diagonal screen size when
watching TV. If you watch TV for a long period of
time, this may cause blurred vision.
Only use the specified type of battery. This could
cause damage to the remote control.
Do not mix new batteries with old batteries. This
may cause the batteries to overheat and leak.
If you install the TV on a stand, you need to take
actions to prevent the product from overturning.
Otherwise, the product may fall over, which may
cause injury.
If you intend to mount the product to a wall, attach
VESA standard mounting interface (optional parts)
to the back of the product. When you install the set
to use the wall mounting bracket (optional parts), fix
it carefully so as not to drop.
Only use the attachments / accessories specified by
the manufacturer.
Batteries should not be exposed to excessive heat.
For example, keep away from direct Sunlight , open
fireplace and electric heaters .
Do not place non-rechargeable batteries in charging
device.
Make sure there are no objects between the remote
control and its sensor.
8
SAFETY INSTRUCTIONS
ENGLISH
ENG
Signal from Remote Control can be interrupted
due to external/internal lighting eg Sunlight,
fluorescent lighting. If this occurs turn off lighting or
darken viewing area.
Periodically examine the cord of your appliance, and
if its appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by
an authorized servicer.
Prevent dust collecting on the power plug pins or
outlet. This may cause a fire hazard.
When connecting external devices such as video
game consoles, make sure the connecting cables
are long enough. Otherwise, the product may
fall over, which may cause injury or damage the
product.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where
the cord exits the appliance.
Do not turn the product On/Off by plugging-in or
unplugging the power plug to the wall outlet. (Do
not use the power plug for switch.) It may cause
mechanical failure or could give an electric shock.
Do not press strongly upon the panel with a hand
or sharp object such as nail, pencil or pen, or make a
scratch on it, as it may cause damage to screen.
Please follow the installation instructions below to
prevent the product from overheating.
• The distance between the product and the wall
should be more than 10 cm.
• Do not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
cupboard).
• Do not install the product on a carpet or
cushion.
• Make sure the air vent is not blocked by a
tablecloth or curtain.
Otherwise, this may result in fire.
Take care not to touch the ventilation openings
when watching the TV for long periods as the
ventilation openings may become hot. This does
not affect the operation or performance of the
product.
Avoid touching the screen or holding your finger(s)
against it for long periods of time. Doing so may
produce some temporary or permanent distortion/
damage to screen.
When cleaning the product and its components,
unplug the power first and wipe it with a soft cloth.
Applying excessive force may cause scratches or
discolouration. Do not spray with water or wipe with
a wet cloth. Never use glass cleaner, car or industrial
shiner, abrasives or wax, benzene, alcohol etc., which
can damage the product and its panel. Otherwise,
this may result in fire, electric shock or product
damage (deformation, corrosion or breakage).
SAFETY INSTRUCTIONS
9
ENGLISH
ENG
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
If the product feels cold to the touch, there may be
a small “flicker” when it is turned on. This is normal,
there is nothing wrong with product.
When unplugging the cable, grab the plug and
unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power cord
from the power board, as this could be hazardous.
When moving the product, make sure you turn
the power off first. Then, unplug the power cables,
antenna cables and all connecting cables.
The TV set or power cord may be damaged, which
may create a fire hazard or cause electric shock.
When moving or unpacking the product, work in
pairs because the product is heavy. Otherwise, this
may result in injury.
Contact the service centre once a year to clean the
internal parts of the product.
Accumulated dust can cause mechanical failure.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
The panel is a high technology display product with
resolution of two million to six million pixels. You
may see tiny black dots and/or brightly coloured
dots (white, red, blue, green) at a size of 1 ppm on
the panel. This does not indicate a malfunction and
does not affect the performance and reliability of
the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or refund.
You may find different brightness and colour of the
panel depending on your viewing position(left/
right/top/down).
This phenomenon occurs due to the characteristic
of the panel. It is not related with the product
performance, and it is not malfunction.
10
SAFETY INSTRUCTIONS
ENGLISH
ENG
Displaying a still image for a prolonged period of
time may cause image sticking. Avoid displaying a
fixed image on the TV screen for a long period of
time.
Generated Sound
“Cracking” noise: A cracking noise that occurs when
watching or turning off the TV is generated by
plastic thermal contraction due to tempera-ture
and humidity. This noise is common for products
where thermal deformation is required. Electrical
circuit humming/panel buzzing: A low level noise
is generated from a high-speed switching circuit,
which supplies a large amount of current to operate
a product. It varies depend-ing on the product.
This generated sound does not affect the
performance and reliability of the product.
Do not use high voltage electrical goods near the
TV(e.g. electric mosquito-swatter). This may result in
product malfunction.
Viewing 3D Imaging (Only 3D models)
WARNING
Viewing environment
yy Viewing Time
-- When watching 3D contents, take 5 - 15
minute breaks every hour. Viewing 3D
contents for a long period of time may
cause headache, dizziness, fatigue or eye
strain.
Those that have a photosensitive
seizure or chronic illness
yy Some users may experience a seizure or other
abnormal symptoms when they are exposed
to a flashing light or particular pattern from 3D
contents.
yy Do not watch 3D videos if you feel nausea, are
pregnant and/ or have a chronic illness such
as epilepsy, cardiac disorder, or blood pressure
disease, etc.
yy 3D Contents are not recommended to those
who suffer from stereo blindness or stereo
anomaly. Double images or discomfort in
viewing may be experienced.
yy If you have strabismus (cross-eyed), amblyopia
(weak eyesight) or astigmatism, you may have
trouble sensing depth and easily feel fatigue
due to double images. It is advised to take
frequent breaks than the average adult.
yy If your eyesight varies between your right and
left eye, correct your eyesight prior to watching
3D contents.
Symptoms which require
discontinuation or refraining from
watching 3D contents
yy Do not watch 3D contents when you feel
fatigue from lack of sleep, overwork or drinking.
yy When these symptoms are experienced, stop
using/watching 3D contents and get enough
rest until the symptom subsides.
-- Consult your doctor when the symptoms
persist. Symptoms may include headache,
eyeball pain, dizziness, nausea, palpitation,
blurriness, discomfort, double image,
visual inconvenience or fatigue.
SAFETY INSTRUCTIONS
11
Cautions when using the 3D glasses
Viewing environment
yy Viewing Distance
-- Maintain a distance of at least twice the
screen diagonal length when watching 3D
contents. If you feel discomfort in viewing
3D contents, move further away from the
TV.
Viewing age
yy Infants/Children
-- Usage/ Viewing 3D contents for children
under the age of 5 are prohibited.
-- Children under the age of 10 may
overreact and become overly excited
because their vision is in development
(for example: trying to touch the screen or
trying to jump into it.) Special monitoring
and extra attention is required for children
watching 3D contents.
-- Children have greater binocular disparity
of 3D presentations than adults because
the distance between the eyes is shorter
than that of adults. Therefore they will
perceive more stereoscopic depth
compared to adults for the same 3D
image.
yy Teenagers
-- Teenagers under the age of 19 may react
with sensitivity due to stimulation from
light in 3D contents. Advise them to refrain
from watching 3D contents for a long time
when they are tired.
yy Elderly
-- The elderly may perceive less 3D effect
compared to the young. Do not sit closer
to the TV than the recommended distance.
� Make sure to use LG 3D glasses. Otherwise, you
may not be able to view 3D videos properly.
� Do not use 3D glasses instead of your normal
glasses, sunglasses or protective goggles.
� Using modified 3D glasses may cause eye strain
or image distortion.
� Do not keep your 3D glasses in extremely high
or low temperatures. It will cause deformation.
� The 3D glasses are fragile and are easily
scratched. Always use a soft, clean piece of
cloth when wiping the lenses. Do not scratch
the lenses of the 3D glasses with sharp objects
or clean/wipe them with chemicals.
ENGLISH
ENG
CAUTION
12
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
NOTE
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
The available menus and options may differ from the input source or product model that you are using.
New features may be added to this TV in the future.
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
be turned off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the picture
is reduced, and this will reduce the overall running cost.
ENGLISH
ENG
yy
yy
yy
yy
yy
INSTALLATION PROCEDURE
1Open the package and make sure all the accessories are included.
2Attach the stand to the TV set.
3Connect an external device to the TV set.
4
Make sure the network connection is available. You can use the TV network functions only when the
network connection is made.
* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take
a few minutes.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer
where you purchased your product. The illustrations in this manual may differ from the actual product and
item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick
does not fit into your TV’s USB port.
*A <
= 10 mm
*B <
= 18 mm
yy Use a certified cable with the HDMI logo attached.
yy If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.
(Recommended HDMI Cable Types)
- High-Speed HDMI®/TM Cable (3m or less)
- High-Speed HDMI®/TM Cable with Ethernet (3m or less)
ASSEMBLING AND PREPARING
ENGLISH
ENG
/ INPUT
P
Magic remote,
Batteries (AA)
(See p. 33)
Owner’s manual
P
Component gender
cable
(See p. 29)
Stand Assy
(Stand Base/Stand
Body)
(Only 55EG91**)
(See p. 18, 19)
13
Composite gender
cable
(See p. 29, 30)
Stand Assy
(Stand Base/Stand
Body)
(Only 55EG92**)
(See p. 19, 20)
Cinema 3D glasses
The number of 3D glasses
may differ depending on
the model or country.
Stand Assy
(Stand Base/Stand
Body)
(Only 55EG96**)
(See p. 19, 20)
Stand Screw
4 EA, M4 x L20
(Only 55EG91**)
5 EA, M4 x L20
(Only 55EG96**,
55EG92**)
8 EA, M4 x L20
(Only 65EG96**)
(See p. 18, 20, 21)
Cable Holder
(See p. 25)
Stand Assy
(Stand Base/Stand
Body)
(Only 65EG96**)
(See p. 21, 22)
14
ASSEMBLING AND PREPARING
ENGLISH
ENG
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AG-F***
Cinema 3D Glasses
AN-MR600
Magic Remote
AN-VC550
Smart Camera
AG-F***DP
Dual Play Glasses
LG Audio Device
Compatibility
EG91**, EG92**, EG96**
AG-F***
Cinema 3D Glasses
•
AN-MR600
Magic Remote
•
AN-VC550
Smart Camera
•
AG-F***DP
Dual Play Glasses
•
LG Audio Device
•
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
ASSEMBLING AND PREPARING
15
A type : EG91**
B type : EG92**
Screen
Screen
Speakers
Joystick Button2
Speakers
Remote Control Sensor
Standby Light
C type : EG96**
Screen
Speakers
Joystick Button2
Remote Control Sensor
and Intelligent Sensor1
LG Logo Light
Joystick Button2
Remote Control Sensor
Standby Light
ENGLISH
ENG
Parts and buttons
16
ENGLISH
ENG
1
2
ASSEMBLING AND PREPARING
Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
Joystick Button - This button is located below the TV screen.
NOTE
yy You can set the LG Logo Light or Standby Light to on or off by selecting GENERAL in the main menus.
Using the joystick button
You can operate the TV by pressing the button or moving the joystick left, right, up, or down.
Basic functions
Power On
When the TV is turned off, place your finger on the joystick button and
press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick button
and press it once for a few seconds and release it. All running apps will
close, and any recording in progress will stop.
Volume
Control
If you place your finger over the joystick button and move it left or
right, you can adjust the volume level you want.
Programmes
Control
If you place your finger over the joystick button and move it up or
down, you can scrolls through the saved programmes you want.
NOTE
yy When your finger over the joystick button and push it to the up, down, left or right, be careful not
to press the joystick button. If you press the joystick button first, you may not be able to adjust the
volume level and saved programmes.
Adjusting the menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items moving the joystick button up, down, left or right.
Turns the power off.
Accesses the Quick Settings.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
ASSEMBLING AND PREPARING
17
ENGLISH
ENG
Lifting and moving the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for safe
transportation regardless of its type and size.
CAUTION
yy Avoid touching the screen at all times, as
this may result in damage to the screen.
yy It is recommended to move the TV in the box or
packing material that the TV originally came in.
yy Before moving or lifting the TV, disconnect the
power cord and all cables.
yy When holding the TV, the screen should face
away from you to avoid damage.
yy Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
yy When transporting a large TV, there should be
at least 2 people.
yy When transporting the TV by hand, hold the TV
as shown in the following illustration.
yy When transporting the TV, do not expose the
TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
yy Do not apply excessive pressure to cause flexing
/bending of frame chassis as it may damage
screen.
yy Be sure to keep your TV upright instead of
laying or tilting it while moving the TV.
yy When handling the TV, be careful not to
damage the protruding joystick button.
18
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the TV
3
(Image shown may differ from your TV.)
Attaching the stand
Only 55EG91**
1
Protective
Package
1
1
4 EA
M4 x L20
Stand cover
1
When assembling the stand, lay the front screen
Protective Package included in the product box
on a table or product box and then place the TV
screen face down on the Protective Package.
4
CAUTION
yy Do not lift your TV without the stand.
The protruding Joystick Button may be
damaged.
Stand
Cover
2
Stand Assy
CAUTION
yy Insert the protruding parts of the Stand
Cover into the holes.
ASSEMBLING AND PREPARING
19
Only 55EG96**, 55EG92**
Stand
cover
ENGLISH
ENG
5
1
Protective
Package
1
1
Stand Cover
1
When assembling the stand, lay the front
screen Protective Package included in the
product box on a table or product box and
then place the TV screen face down on the
Protective Package.
CAUTION
Cover holder
yy Do not lift your TV without the stand.
The protruding Joystick Button may be
damaged.
CAUTION
yy Insert the Cover Holder of the Stand Cover
into the holes until it clicks. Press the Stand
Cover gently so that the non-woven fabric
inside is attached tightly.
2
Stand Assy
20
ASSEMBLING AND PREPARING
ENGLISH
ENG
3
5
Stand
Cover
5 EA
M4 x L20
Cover Holder
4
CAUTION
Stand
Cover
CAUTION
yy Insert the protruding parts of the Stand
Cover into the holes.
yy Insert the Cover Holder of the Stand Cover
into the holes until it clicks. Press the Stand
Cover gently so that the non-woven fabric
inside is attached tightly.
ASSEMBLING AND PREPARING
Only 65EG96**
21
ENGLISH
ENG
3
1
Protective
Package
1
1
Stand Cover
1
8 EA
M4 x L20
When assembling the stand, lay the front screen
Protective Package included in the product box
on a table or product box and then place the TV
screen face down on the Protective Package.
CAUTION
yy Do not lift your TV without the stand.
The protruding Joystick Button may be
damaged.
4
Stand
Cover
2
Stand Assy
CAUTION
yy Insert the protruding parts of the Stand
Cover into the holes.
22
ASSEMBLING AND PREPARING
ENGLISH
ENG
5
Stand
Cover
Cover Holder
CAUTION
yy Insert the Cover Holder of the Stand Cover
into the holes until it clicks. Press the Stand
Cover gently so that the non-woven fabric
inside is attached tightly.
CAUTION
yy When attaching the stand to the TV set, place
the screen facing down on a cushioned table
or flat surface to protect the screen from
scratches.
yy Make sure that the screws are inserted
correctly and fastened securely. (If they are
not fastened securely enough, the TV may tilt
forward after being installed.)
Do not use too much force and over tighten
the screws; otherwise screw may be damaged
and not tighten correctly.
NOTE
yy Remove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
ASSEMBLING AND PREPARING
(Image shown may differ from your TV.)
1
Lift and tilt the TV into its upright position on a
table.
-- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
5 cm
2
10 cm
Connect the power cord to a wall outlet.
CAUTION
yy Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
WARNING
yy If a television is not positioned in a
sufficiently stable location, it can be
potentially hazardous due to falling. Many
injuries, particularly to children, can be
avoided by taking simple precautions such
as:
»» Using cabinets or stands recommended
by the manufacturer of the television.
»» Only using furniture that can safely
support the television.
»» Ensuring the television is not
overhanging the edge of the
supporting furniture.
»» Not placing the television on tall
furniture (for example, cupboards or
bookcases) without anchoring both the
furniture and the television to a suitable
support.
»» Not standing the televisions on cloth
or other materials placed between the
television and supporting furniture.
»» Educating children about the dangers
of climbing on furniture to reach the
television or its controls.
ENGLISH
ENG
Mounting on a table
23
24
ASSEMBLING AND PREPARING
Securing the TV to a wall
ENGLISH
ENG
(This feature is not available for all models.)
Mounting on a wall
Attach an optional wall mount bracket at the rear of
the TV carefully and install the wall mount bracket
on a solid wall perpendicular to the floor. When you
attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm
10 cm
10 cm
1
2
3
Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
yy Make sure that children do not climb on or
hang on the TV.
10 cm
Make sure to use screws and wall mount bracket
that meet the standard. Standard dimensions for
the wall mount kits are described in the following
table.
Separate purchase(Wall mounting bracket)
Model
AxBxC
(mm)
55EG91**
55EG92**
55EG96**
200 x 340 x 195
65EG96**
200 x 330 x 120
A
A
B
B
C
NOTE
yy Use a platform or cabinet that is strong and
large enough to support the TV securely.
yy Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
Standard
screw
Number of
screws
Wall mount
bracket
C
M6
4
OTW150
ASSEMBLING AND PREPARING
yy Disconnect the power first, and then move
or install the TV. Otherwise electric shock
may occur.
yy If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and
contact the local dealer or qualified
personnel.
yy Do not over tighten the screws as this may
cause damage to the TV and void your
warranty.
yy Use the screws and wall mounts that meet
the standard. Any damages or injuries by
misuse or using an improper accessory are
not covered by the manufacturer’s warranty.
Tidying cables
(Image shown may differ from your TV.)
Gather and bind the cables with the cable holder.
NOTE
yy Use the screws that are listed on the
standard screw specifications.
yy The wall mount kit includes an installation
manual and necessary parts.
yy The wall mount bracket is not provided. You
can obtain additional accessories from your
local dealer.
yy The length of screws may differ depending
on the wall mount. Make sure to use the
proper length.
yy For more information, refer to the manual
supplied with the wall mount.
Cable Holder
CAUTION
yy Do not move the TV by holding the cable
holder, as the cable holder may break, and
injuries and damage to the TV may occur.
ENGLISH
ENG
CAUTION
25
26
MAKING CONNECTIONS
ENGLISH
ENG
MAKING CONNECTIONS
Antenna connection
This section on MAKING CONNECTIONS mainly
uses diagrams for the EG96** models.
Connect the TV to a wall antenna socket with an RF
cable (75 Ω).
Connect various external devices to the TV and
switch input modes to select an external device. For
more information of external device’s connection,
refer to the manual provided with each device.
Available external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
NOTE
yy The external device connection may differ
from the model.
yy Connect external devices to the TV
regardless of the order of the TV port.
yy If you record a TV program on a DVD
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
of recording, refer to the manual provided
with the connected device.
yy Refer to the external equipment’s manual
for operating instructions.
yy If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
yy In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change the
PC output to another resolution, change
the refresh rate to another rate or adjust
the brightness and contrast on the PICTURE
menu until the picture is clear.
yy In PC mode, some resolution settings
may not work properly depending on the
graphics card.
yy If ULTRA HD content is played via PC,
the video or audio may have disruptions
intermittently depending on your PC’s
performance. (Depending on model)
(*Not
Provided)
Wall Antenna
Socket
NOTE
yy Use a signal splitter to use more than 2 TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
yy If the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
yy An antenna cable and converter are not
provided.
yy Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC.
yy For a location that is not supported with
ULTRA HD broadcasting, this TV cannot
receive ULTRA HD broadcasts directly. This
TV cannot receive ULTRA HD (3840 x 2160
pixels) broadcasts directly because the
related standards have not been confirmed.
(Depending on model)
MAKING CONNECTIONS
HDMI connection
(Only EG91**)
ENGLISH
ENG
Transmits the digital video and audio signals from
an external device to the TV. Connect the external
device and the TV with the HDMI cable as shown.
(Only EG96**, EG92**)
(*Not
Provided)
(*Not
Provided)
HDMI
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
HDMI
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
27
ARC (Audio Return Channel)
yyAn external audio device that supports
SIMPLINK and ARC must be connected
using HDMI(4K @ 60 Hz)/DVI IN 2 (ARC)
or HDMI/DVI IN 3 (ARC) port.
yyWhen connected with a high-speed
HDMI cable, the external audio device
that supports ARC outputs optical SPDIF
without additional optical audio cable and
supports the SIMPLINK function.
28
MAKING CONNECTIONS
ENGLISH
ENG
(Only EG96**, EG92**)
DVI to HDMI connection
Picture HDMI ULTRA HD
Deep Colour :
yy On - Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
yy Off - Support 4K @ 50/60 Hz (4:2:0)
Transmits the digital video signal from an external
device to the TV. Connect the external device
and the TV with the DVI-HDMI cable as shown. To
transmit an audio signal, connect an audio cable.
If the device connected to Input Port also supports
ULTRA HD Deep Colour, your picture may be clearer.
However, if the device doesn’t support it, it may not
work properly.
In that case, connect the device to a different HDMI
port or change the TV’s HDMI ULTRA HD Deep
Colour setting to Off. (This feature is available on
certain models which are supported ULTRA HD
Deep Colour only. )
(Only EG96**, EG92**)
NOTE
yyThe external device connection may differ
from the model.
yyIt is recommended to use the TV with the
HDMI connection for the best image quality.
yyUse the latest High Speed HDMI™ Cable
with CEC (Customer Electronics Control)
function.
yyHigh Speed HDMI™ Cables are tested to
carry an HD signal up to 1080p and higher.
yySupported HDMI Audio format : Dolby
Digital (32 kHz, 44.1 kHz, 48 kHz), DTS (44.1
kHz, 48 kHz), PCM (32 kHz, 44.1 kHz, 48 kHz,
96 kHz, 192 kHz) (Depending on model)
AV
IN
( Audio in)
(*Not
Provided)
AUDIO OUT
DVI OUT
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
MAKING CONNECTIONS
29
Transmits analogue video and audio signals from an
external device to the TV. Connect the external device
and the TV with a component gender cable as shown.
AV
IN
( Audio in)
IN
AV
VIDEO
COMPONENT
AUDIO
PR
PB
Y
(*Not
Provided)
AUDIO OUT
YELLOW
(Use the composite
gender cable provided.)
DVI OUT
BLUE
RED
BLUE
RED
GREEN GREEN
RED
NOTE
(*Not Provided)
RED
BLUE
GREEN
L
RED
WHITE
yyDepending on the graphics card, DOS mode
may not work if a HDMI to DVI Cable is in
use.
yyWhen using the HDMI / DVI cable, Single link
is only supported.
RED
WHITE WHITE
YELLOW
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
GREEN
(Use the component
gender cable provided.)
R
AUDIO
VIDEO
DVD / Blu-Ray / HD Cable Box
NOTE
yyIf cables are not installed correctly, it could
cause this image to display in black and
white or with distorted colours.
ENGLISH
ENG
Component connection
(Only EG91**)
30
MAKING CONNECTIONS
ENGLISH
ENG
Composite connection
Audio connection
Transmits analogue video and audio signals from
an external device to the TV. Connect the external
device and the TV with a composite gender cable as
shown.
You may use an external audio system instead of
the built-in speaker.
Digital optical audio connection
Transmits a digital audio signal from the TV to an
external device. Connect the external device and
the TV with the optical audio cable as shown.
AV
VIDEO
IN
COMPONENT
AUDIO
PR
PB
Y
YELLOW
(Use the composite gender cable provided.)
RED
WHITE
RED
WHITE
YELLOW YELLOW
(*Not Provided)
(*Not Provided)
RED
WHITE
YELLOW
OPTICAL AUDIO IN
Digital Audio System
CAUTION
VIDEO
DVD / Blu-Ray /
HD Cable Box / VCR
L (MONO) AUDIO R
yyDo not look into the optical output port.
Looking at the laser beam may damage your
vision.
yyAudio with ACP (Audio Copy Protection)
function may block digital audio output.
MAKING CONNECTIONS
31
USB connection
Transmits the headphone signal from the TV to an
external device. Connect the external device and the
TV with the headphone as shown.
Connect a USB storage device such as a USB flash
memory, external hard drive or a USB memory card
reader to the TV and access the Smart Share menu
to use various multimedia files.
(Only EG96**)
(Only EG96**, EG92**)
Headphone (*Not Provided)
NOTE
yyAUDIO menu items are disabled when connecting a headphone.
yyOptical Digital Audio Out is not available
when connecting a headphone.
yyHeadphone impedance: 16 Ω
yyMax audio output of headphone: 0.627 mW
to 1.334 mW
yyHeadphone jack size: 0.35 cm
HDD
(*Not Provided)
HUB
(*Not Provided)
USB
(*Not Provided)
ENGLISH
ENG
Headphone connection
32
MAKING CONNECTIONS
(Only EG91**)
ENGLISH
ENG
HDD
(*Not Provided)
HUB
(*Not Provided)
USB
(*Not Provided)
NOTE
yySome USB Hubs may not work. If a USB
device connected using a USB Hub is not
detected, connect it to the USB IN port on
the TV directly.
yyConnect the external power source if your
USB is needed.
yyConnecting via USB 3.0 : Some USB device
may not work if it dose not meet USB 3.0
standard. In case, connect it to USB IN 2 or
USB IN 3 port. (Only EG96**, EG92**)
MAGIC REMOTE FUNCTIONS
33
When the message “Magic Remote battery is low. Change the battery.” is displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching and ends to the label
inside the compartment, and close the battery cover. Be sure to point the remote control toward the remote
control sensor on the TV. To remove the batteries, perform the installation actions in reverse.
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
yy In Analogue TV and some countries, some remote control buttons may not work.
1. @
2 abc
3 def
4 ghi
5 jkl
6 mno
7pqrs
8 tuv
9wxyz
LIST
0
INFO
EXIT
GUIDE
TEXT
T.OPT
SUBT.
(POWER) Turns the TV on or off.
(INPUT) Changes the input source.
* Pressing and holding the
button displays all the lists of external inputs.
Number buttons Enters numbers.
Accesses the saved programmes list.
Views the information of the current programmes and screen.
Adjusts the volume level.
P
Scrolls through the saved programmes.
(MUTE) Mutes all sounds.
* By pressing and holding the
button, audio descriptions function will
be enabled. (Depending on model)
(HOME) Accesses the Home menu.
(BACK) Returns to the previous screen.
Clears on-screen displays and returns to last input viewing.
ENGLISH
ENG
MAGIC REMOTE FUNCTIONS
34
MAGIC REMOTE FUNCTIONS
ENGLISH
ENG
1. @
2 abc
3 def
4 ghi
5 jkl
6 mno
7pqrs
8 tuv
9wxyz
LIST
0
INFO
EXIT
GUIDE
TEXT
T.OPT
SUBT.
Wheel (OK) Press the center of the Wheel button to select a menu. You
can change programmes by using the wheel button.
Navigation buttons (up/down/left/right)
Press the up, down, left or right button to scroll the menu.
If you press
buttons while the pointer is in use, the pointer will
disappear from the screen and Magic Remote will operate like a general
remote control. To display the pointer on the screen again, shake Magic Remote to
the left and right.
Shows programme guide.
(Screen Remote) Displays the Screen Remote.
*Accesses the Universal Control Menu. (Depending on model)
Used for viewing 3D video.
(Voice recognition)
(Depending on model)
Network connection is required to use the voice recognition function.
1. Press the voice recognition button.
2. Speak when the voice display window appears on the TV screen.
yy Use the Magic Remote no further than 10 cm from your face.
yy The voice recognition may fail when you speak too fast or too slowly.
yy The recognition rate may vary depending on the user’s characteristics
(voice, pronunciation, intonation, and speed) and the environment (noise
and TV volume).
(Q. Settings) Accesses the Quick Settings.
* Pressing and holding the button displays the Advanced menu.
Coloured buttons These access special functions in some menus.
( : Red,
: Green,
: Yellow,
: Blue)
TELETEXT buttons(
,
) These buttons are used for teletext.
Recalls your preferred subtitle in digital mode.
MAGIC REMOTE FUNCTIONS
HOME
How to register
the magic remote
BACK
To use the Magic Remote, first pair it
with your TV.
1Put batteries into the Magic
Remote and turn the TV on.
Wheel
(OK)
P
MY APPS
2Point the Magic Remote at your TV
and press the
Wheel (OK) on
the remote control.
* If the TV fails to register the Magic
Remote, try again after turning the
TV off and back on.
How to deregister the magic remote
(BACK)
Press the
(BACK) and
(HOME) buttons at the same time,
for five seconds, to unpair the Magic
Remote with your TV.
(HOME)
* Pressing and holding the
button will let you cancel and reregister Magic Remote at once.
How to use magic remote
yy Shake the Magic Remote
slightly to the right and left or
press
(HOME), (INPUT),
buttons to make the
pointer appear on the screen.
(In some TV models, the
pointer will appear when
you turn the Wheel (OK)
button.)
yy If the pointer has not been
used for a certain period
of time or Magic Remote is
placed on a flat surface, then
the pointer will disappear.
yy If the pointer is not
responding smoothly, you can
reset the pointer by moving it
to the edge of the screen.
yy The Magic Remote depletes
batteries faster than a normal
remote due to the additional
features.
Precautions to take when using the
magic remote
yy Use the remote control within the specified
range (within 10 m).
You may experience communication failures
when using the device outside the coverage
area or if there are obstacles within the coverage
area.
yy You may experience communication failures
depending on the accessories.
Devices such as a microwave oven and wireless
LAN operate in the same frequency band (2.4
GHz) as the Magic Remote. This may cause
communication failures.
yy The Magic Remote may not work properly if a
wireless router (AP) is within 1 meter of the TV.
Your wireless router should be more than 1 m
away from the TV.
yy Do not disassemble or heat the battery.
yy Do not drop the battery. Avoid extreme shocks
to the battery.
yy Inserting the battery in the wrong way may
result in explosion.
ENGLISH
ENG
Registering magic remote
35
36
USING THE USER GUIDE / MAINTENANCE
ENGLISH
ENG
USING THE USER GUIDE
MAINTENANCE
User Guide allows you to more easily access the
detailed TV information.
Cleaning your TV
1 Press the
menu.
(HOME) button to access the Home
Clean your TV regularly to keep the best
performance and to extend the product lifespan.
CAUTION
2 Select User Guide and press the
button.
Wheel(OK)
yy Make sure to turn the power off and disconnect
the power cord and all other cables first.
yy When the TV is left unattended and unused for
a long time, disconnect the power cord from
the wall outlet to prevent possible damage
from lightning or power surges.
Screen, frame, cabinet and stand

yy To remove dust or light dirt, wipe the surface
with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a
soft cloth dampened in clean water or a diluted
mild detergent. Then wipe immediately with a
dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this
may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with
your fingernail or a sharp object, as this may
result in scratches and image distortions.
yy Do not use any chemicals as this may damage
the product.
yy Do not spray liquid onto the surface. If water
enters the TV, it may result in fire, electric shock,
or malfunction.
Power cord
Remove the accumulated dust or dirt on the power
cord regularly.
TROUBLESHOOTING / EXTERNAL CONTROL DEVICE SETUP
37
Problem
Solution
Cannot control the TV with
the remote control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
yy Check if the batteries are still working and properly installed
( to ,
to ).
No image display and no
sound is produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Sleep Timer or Timer Power Off feature is activated in the
TIMERS settings.
yy If there is no signal while the TV is on, the TV will turn off automatically
after 15 minutes of inactivity.
When connecting to the PC
(HDMI/DVI), ‘No signal’ or
‘Invalid Format’ is displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the HDMI cable.
yy Restart the PC with the TV on.
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com.
ENGLISH
ENG
TROUBLESHOOTING
38
SPECIFICATIONS
ENGLISH
ENG
SPECIFICATIONS
(Only EG91**, EG92**, EG96**)
Wireless module(LGSBW41) Specifications
Wireless LAN
Standard
IEEE 802.11a/b/g/n
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz(for Non EU)
Frequency
Range
Output Power
(Max.)
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4 GHz: 16 dBm
802.11n - 5 GHz: 16 dBm
Bluetooth
Standard
Frequency
Range
Output Power
(Max.)
Bluetooth Version 4.0
2400 to 2483.5 MHz
10 dBm or Lower
yy Because band channel used by the country could be different, the user can not change or adjust the
operating frequency and this product is set for the regional frequency table.
yy This device should be installed and operated with minimum distance 20 cm between the device and
your body. And this phrase is for the general statement for consideration of user environment.
0197
0197
SPECIFICATIONS
Thickness(T)
Depth(D)
EG96**
MODELS
Dimensions
Weight
With stand (mm)
(W x H x D)
Without stand (mm)
(W x H x T(D))
With stand (kg)
Without stand (kg)
55EG960T-TA
55EG960Y-TA
55EG965T-TA
55EG965Y-TA
65EG960T-TA
65EG960Y-TA
65EG965T-TA
65EG965Y-TA
1226 x 760 x 213
1447 x 884 x 237
1226 x 719 x 50.1(87.8)
1447 x 842 x 50.1(102.5)
19
26.9
15.3
21.7
AC 100-240 V~ 50 / 60 Hz
Power requirement
EG92**
MODELS
Dimensions
Weight
With stand (mm)
(W x H x D)
Without stand (mm)
(W x H x T(D))
55EG920T-TA
55EG920Y-TA
1225 x 762 x 191
1225 x 719 x 48.9(87.3)
With stand (kg)
16.5
Without stand (kg)
13.2
AC 100-240 V~ 50 / 60 Hz
Power requirement
EG91**
MODELS
Dimensions
Weight
With stand (mm)
(W x H x D)
Without stand (mm)
(W x H x T(D))
With stand (kg)
Without stand (kg)
1225 x 760 x 208
1225 x 719 x 48.9(87.3)
15.0
12.8
AC 100-240 V~ 50 / 60 Hz
Power requirement
Operating Temperature
Environment
condition
55EG910T-TB
55EG910Y-TB
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
ENGLISH
ENG
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
39
40
SPECIFICATIONS
Analogue TV
(Depending on country)
(Depending on country)
Television System
DVB-T(*DVB-T/T2)
PAL B/B, PAL B/G, PAL D/K, PAL-I
SECAM B/G, SECAM D/K
NTSC-M
Programme Coverage
VHF, UHF
VHF, UHF, CATV
ENGLISH
ENG
Digital TV
Maximum number of storable
programmes
DVB-T/T2 & Analogue TV : 1,500
External Antenna Impedance
75 Ω
* : Only DVB-T2 support models.
41
WEEE
0197
Disposal of your appliance
The symbol indicating separate collection for electrical and electronic equipment consists of
the crossed-out wheeled bin.
0197
ENGLISH
ENG
(Only Jordan)
For any Suggestion, Opinion,
Complaints, Please Call
800 54 in UAE
0800 545454 in South Africa
080 100 54 54 in Morocco
19960 in Egypt
021 36 54 54 in Algeria
Other countries, Please contact our
local dealer or log into
http://www.lg.com
Record the model number and serial number
of the TV.
Refer to the label on the back cover and
quote this information to your dealer when
requiring any service.
MODEL
SERIAL
(Only DTV)
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com
2
KEY CODES
ENGLISH
ENG
KEY CODES
• This feature is not available for all models.
Code
(Hexa)
Function
Note
Code
(Hexa)
Function
Note
00
CH +, PR +
R/C Button
53
List
R/C Button
01
CH -, PR -
R/C Button
5B
Exit
R/C Button
02
Volume +
R/C Button
60
PIP(AD)
R/C Button
03
Volume -
R/C Button
61
Blue
R/C Button
06
> (Arrow Key / Right Key)
R/C Button
63
Yellow
R/C Button
07
< (Arrow Key / Left Key)
R/C Button
71
Green
R/C Button
08
Power
R/C Button
72
Red
R/C Button
09
Mute
R/C Button
79
Ratio / Aspect Ratio
R/C Button
0B
Input
R/C Button
91
AD (Audio Description)
R/C Button
0E
SLEEP
R/C Button
7A
User Guide
R/C Button
0F
TV, TV/RAD
R/C Button
7C
Smart / Home
R/C Button
R/C Button
7E
SIMPLINK
R/C Button
10 - 19 * Number Key 0 - 9
1A
Q.View / Flashback
R/C Button
8E
►► (Forward)
R/C Button
1E
FAV (Favorite Channel)
R/C Button
8F
◄◄ (Rewind)
R/C Button
20
Text (Teletext)
R/C Button
AA
Info
R/C Button
21
T. Opt (Teletext Option)
R/C Button
AB
Program Guide
R/C Button
28
Return (BACK)
R/C Button
B0
► (Play)
R/C Button
30
AV (Audio / Video) Mode
R/C Button
B1
ꕗ (Stop / File List)
R/C Button
39
Caption/Subtitle
R/C Button
BA
ꕘ (Freeze / Slow Play /
Pause)
R/C Button
40
Λ (Arrow Key / Cursor Up)
R/C Button
BB
Soccer
R/C Button
41
V (Arrow Key / Cursor
Down)
R/C Button
BD
ꔄ (REC)
R/C Button
42
My Apps
R/C Button
DC
3D
R/C Button
43
Menu / Settings
R/C Button
99
AutoConfig
R/C Button
44
OK / Enter
R/C Button
9F
App / *
R/C Button
45
Q.Menu
R/C Button
9B
TV/PC
R/C Button
4C
List, - (ATSC Only)
R/C Button
* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
EXTERNAL CONTROL DEVICE SETUP
3
• Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Note: The type of control port on the TV can be different between model series.
* Please be advised that not all models support this type of connectivity.
* Cable is not provided.
USB to Serial converter with USB Cable
USB IN
USB Type
(PC)
(TV)
• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product
ID :IN0x2008) USB to serial converter
RS-232C
(CONTROL & SERVICE)
which is not made nor provided by LG.
• It can be purchased from computer stores that carry accessories for IT support professionals.
(TV)
(PC)
USB IN
RS-232C With RS232C Cable
(PC)
(TV)
SERVICE ONLY
DE9 (D-Sub 9pin) Type
1
• You need to purchase the RS-232C (DE9, D-Sub
3 9pin female-to-female type) to RS-232C cable required
for the connection between the PC and the TV, which is specified in the manual.
(PC)
2
RS-232C IN
(CONTROL & SERVICE)
(PC)
SERVICE ONLY
1
3
RS-232C IN
(CONTROL & SERVICE)
2
(PC)
(TV)
1
3
(PC)
The connection interface may differ from your TV.
(TV)
2
(TV)
(TV)
1
3
(PC)
RS-232C IN
2
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
(CONTROL & SERVICE)
(TV)
ENGLISH
ENG
EXTERNAL CONTROL DEVICE SETUP
USB USB
IN IN
4
EXTERNAL CONTROL DEVICE SETUP
(PC)
(PC)
(TV)
(TV)
RS-232C IN
(CONTROL
SERVICE)
• You need to purchase the phone-jack to RS-232 cable required
for &the
connection between the PC and
the TV, which is specified in the manual.
RS-232C IN
(PC)
(PC)
(CONTROL & SERVICE)
* For other models, connect to the USB port.
* The connection interface may differ from your TV.
1
3
(PC)
(PC)
1
3
2
2
- or
(TV)
(TV)
(TV)
(TV)
1
3
(PC)
(PC)
SERVICE
ONLY ONLY
SERVICE
ENGLISH
ENG
Phone jack Type
1
3
RS-232C IN
(CONTROL & SERVICE)
2
RS-232C IN
(CONTROL & SERVICE)
2
Customer Computer
(TV)
(TV)
RS-232C configurations
3-Wire Configurations(Not standard)
1
5
PC
RXD
RS-232C IN
(CONTROL & SERVICE)
TXD
RS-232C IN
(CONTROL & SERVICE)
GND
6
2
2
TXD
3
1
RXD
5
3
GND
OR
9
RS-232C
(Serial port)
TV
RXD
3
2
TXD
TXD
2
1
RXD
GND
5
3
GND
D-Sub 9
Phone
Set ID
For Set ID number, see "Real Data Mapping" on p.6
1. Press SETTINGS to access the main menus.
2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending on model)
EXTERNAL CONTROL DEVICE SETUP
5
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
ENGLISH
ENG
Communication Parameters
• Stop bit : 1 bit
• Communication code : ASCII code
• Use a crossed (reverse) cable.
Command reference list
(Depending on model)
COMMAND1 COMMAND2
DATA
(Hexadecimal)
01. Power*
k
a
00 to 01
02. Aspect
Ratio
k
c
(p.7)
03. Screen
Mute
k
d
(p.7)
k
e
00 to 01
k
f
00 to 64
06. Contrast
k
g
00 to 64
07.
Brightness
k
h
00 to 64
08. Color/
Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
k
00 to 32
l
00 to 01
m
00 to 01
04. Volume
Mute
05. Volume
Control
10.
k
Sharpness
11. OSD
k
Select
12. Remote
Control Lock k
Mode
13. Treble
k
r
00 to 64
14. Bass
k
s
00 to 64
COMMAND1 COMMAND2
DATA
(Hexadecimal)
15. Balance k
16. Color
(Colour)
x
Temperature
17. ISM
Method (Only j
Plasma TV)
t
00 to 64
u
00 to 64
p
(p.8)
18. Equalizer j
v
(p.8)
q
00 to 05
a
(p.9)
b
00 to 01
19. Energy
j
Saving
20. Tune
m
Command
21. Channel m
(Programme)
Add/Del(Skip)
22. Key
m
c
Key Codes
23. Control
Backlight,
Control Panel
Light
24. Input
select (Main)
25. 3D (Only
3D models)
26. Extended
3D (Only 3D
models)
27. Auto
Configure
m
g
00 to 64
x
b
(p.11)
x
t
(p.11)
x
v
(p.11)
j
u
(p.12)
* Note:During playing or recording media, all commands except Power (ka) and Key (mc) are not
executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
6
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID]
:You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ]
: Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0
01 : Step 1 (Set ID 1)
...
0A : Step 10 (Set ID 10)
...
0F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
...
32 : Step 50 (Set ID 50)
33 : Step 51 (Set ID 51)
...
63 : Step 99 (Set ID 99)
...
C7 : Step 199
C8 : Step 200
...
FE : Step 254
FF : Step 255
...
01 00 : Step 256
...
27 0E : Step 9998
27 0F : Step 9999
...
EXTERNAL CONTROL DEVICE SETUP
7
01.Power (Command: k a)
►► To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
* Similarly, if other functions transmit ‘FF’ data
based on this format, Acknowledgement feedback
presents status about each function.
02.Aspect Ratio (Command: k c)
(Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen 07 : 14:9
(4:3)
(Europe, Colombia, Mid-East,
02 : Wide screen
Asia except South Korea and
(16:9)
Japan)
04 : Zoom
09 : * Just Scan
05 : Zoom 2
0B : Full Wide
(Latin America
(Europe, Colombia, Midexcept Colombia
East, Asia except South
Only)
Korea and Japan)
06 : Set by Program/ 10 to 1F : C
inema Zoom 1
Original
to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
04.Volume Mute (Command: k e)
►► To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05.Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06.Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition),
Just Scan is available.
* Full wide mode may work differently based on
model and is supported for DTV fully, and ATV,
AV partially.
07.Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
03.Screen Mute (Command: k d)
►► To select screen mute on/off.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
08.Color/Colour (Command: k i)
►► To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
ENGLISH
ENG
* Commands may work differently depending on model and signal.
8
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Data Min : 00 to Max : 64
* (Depending on model)
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
09.Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0
0 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10.Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
14. Bass (Command: k s)
►► To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)
15.Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
16.Color(Colour) Temperature (Command: x u)
11.OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
►► To adjust colour temperature. You can also adjust
Color(Colour) Temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
17.ISM Method (Command: j p) (Only Plasma TV)
12.Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
►► To control the ISM method. You can also adjust
ISM Method in OPTION menu.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data Min : 02: Orbiter
08: Normal
20: Color(Colour) Wash
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
18.Equalizer (Command : j v)
►► Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not
turn on by power on key of IR & Local Key.
0
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
0
0
0
0
Frequency
13. Treble (Command: k r)
►► To adjust treble.
You can also adjust in the AUDIO menu.
LSB
0
0
0
Data
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
1st Band
0
0
0
0
0
0(decimal)
0
0
1
2nd Band
0
0
0
0
1
1(decimal)
0
1
0
3rd Band
...
...
...
...
...
...
0
1
1
4th Band
1
0
0
1
1
19(decimal)
EXTERNAL CONTROL DEVICE SETUP
0
0
5th Band
1
0
1
0
0
20(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends on model, and can adjust when sound
mode is EQ adjustable value.
19.Energy Saving (Command: j q)
►► To reduce the power consumption of the TV. You
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data
00 : Off
01 : Minimum
02 : Medium
03 : Maximum
04 : Auto (For LCD TV / LED TV) /
Intelligent sensor (For PDP TV)
05 : Screen off
* (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
Set ID = All = 00
Data 00 & 01 = Channel Data is 10 = 00 0a
Data 02 = Analog Antenna TV = 00
Result = ma 00 00 0a 00
2.Tune to the digital antenna (DVB-T) Channel 01.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1 = 00 01
Data 02 = Digital Antenna TV = 10
Result = ma 00 00 01 10
3.Tune to the satellite (DVB-S) Channel 1000.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
• For South Korea, North/Latin America except
Colombia Model
►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
20.Tune Command (Command: m a)
* This command may work differently depending on
model and signal.
• For Europe, Mid-East, Colombia, Asia except
South Korea and Japan Model
►► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
* Analog Antenna/Cable
[Data 00][Data 01] Channel Data
Data00 : High byte channel data
Data01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog)
- 00 : Antenna TV (ATV)
- 80 : Cable TV (CATV)
* Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data
Data00 : High Channel data
Data01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
Data02 : Input Source (Digital)
- 10 : Antenna TV (DTV)
- 20 : Antenna Radio (Radio)
- 40 : Satellite TV (SDTV)
- 50 : Satellite Radio (S-Radio)
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
* Tune Command Examples:
1.Tune to the Analog antenna (PAL) Channel 10.
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
* Analog Antenna/Cable
Data00 : Physical Channel Number
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data01 & 02: xx (Don't care)
Data03 & 04: xx (Don't care)
Data05: Input Source (Analog)
- 00 : Antenna TV (ATV)
- 01 : Cable TV (CATV)
* Digital Antenna/Cable
Data00 : xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data01 : High byte Channel Data
Data02 : Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data03 : High byte Channel Data
Data04 : Low byte Channel Data
Data05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel
Number
- 06 : Cable TV (CADTV) – Use Physical Channel
ENGLISH
ENG
1
9
10 EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Number
- 22 : Antenna TV (DTV) – Don’t Use Physical
Channel Number
- 26 : Cable TV (CADTV) - Don’t Use Physical
Channel Number
- 46 : Cable TV (CADTV) – Use Major Channel
Number Only (One Part Channel)
Two bytes are available for each major and minor
channel data, but usually the low byte is used alone
(high byte is 0).
* Tune Command Examples:
1.Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01
Total = ma 00 23 00 00 00 00 01
2.Tune to the digital antenna (ATSC) channel 30-3.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Antenna TV = 22
Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
• For Japan Model
►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Data 05 = Digital Antenna TV = 02
Total = ma 00 00 00 11 00 01 02
2.Tune to the BS (ISDB-BS) channel 30.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00
Data 05 = Digital BS TV = 07
Total = ma 00 00 00 1E 00 00 07
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
21.Channel(Programme) Add/Del(Skip)
(Command: m b)
►► To skip current channel(programme) for next time.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Del(ATSC,ISDB)/Skip(DVB)
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del(ATSC, ISDB)/
skip(DVB) or add.
22.Key (Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
* Digital Antenna/Satellite
Data 00: xx (Don't care)
DataKey code - p.2.
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
23.Control Backlight (Command: m g)
[Data 03][Data 04]: Minor/Branch Channel Number
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Antenna TV (DTV)
- 07 : BS (Broadcasting Satellite)
- 08 : CS1 (Communication Satellite 1)
- 09 : CS2 (Communication Satellite 2)
* Tune Command Examples:
1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
01 : Add
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
• For LCD TV / LED TV
►► To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Control Panel Light (Command: m g)
• For Plasma TV
►► To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
00 : DTV
01 : CADTV
02 : Satellite DTV
10 : ATV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
O
01
X
X
X
02
X
X
X
03
X
O
O
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
20 : AV or AV1
21 : AV2
40 : Component1
60 : RGB
41 : Component2
90 : HDMI1
92 : HDMI3
91 : HDMI2
93 : HDMI4
26.Extended 3D(Command: x v) (only 3D models)
(Depending on model)
►► To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
[Data 01][Cr]
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
25.3D(Command: x t) (only 3D models)
(Depending on model)
►► To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr]
* (Depending on model)
DataStructure
[Data 00]00 : 3D On
01 : 3D Off
02 : 3D to 2D
03 : 2D to 3D
[Data 01]00 : Top and Bottom
01 : Side by Side
02 : Check Board
03 : Frame Sequential
04 : Column interleaving
05 : Row interleaving
[Data 02]00 : Right to Left
01 : Left to Right
[Data 03]3D Effect(3D Depth): Min : 00 - Max : 14
(*transmit by Hexadecimal code)
* [Data 02], [Data 03] functions depend on model
and signal.
* If [Data 00] is 00 (3D On), [Data 03] has no
meaning.
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
01], [Data 02] and [Data 03] have no meaning.
* If [Data 00] is 03 (2D to 3D), [Data 01] and
[Data 02] have no meaning.
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data
03] works when 3D Mode (Genre) is manual only.
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal.
[Data 02]
O
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
[Data 01]
O
X : don’t care
[Data 00]
00
[Data 03]
[Data 00]3D option
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)
[Data 01]It has own range for each 3D option
determined by [Data 00].
1) When[Data 00] is 00
00 : Right to Left
01 : Left to Right
2) When[Data 00] is 01, 02
DataMin: 0 - Max: 14 (*transmit by Hexadecimal
code)
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending on model)
* This option works when 3D Mode (Genre) is manual
only.
3) When[Data 00] is 06, 07
00 : Off
01 : On
4) When[Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
converted 2D video
01 : Change 3D video to 2D video, except
2D-to-3D video
* If conversion condition doesn’t meet, command is
treated as NG.
5) When [Data 00] is 09
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
05 : Auto
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
[v][ ][Set ID][ ][NG][Data00][x]
ENGLISH
ENG
24.Input select (Command: x b)
(Main Picture Input)
11
12 EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
27.Auto Configure (Command: j u)
(Depending on model)
►► To adjust picture position and minimize image
shaking automatically. It works only in RGB (PC)
mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : Run Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Download PDF