LG | 43LX341C | LG 43LX341C Owner’s Manual

LED TV
LX341*
LX540*
www.lg.com
AAA
c
d
a
X8
(M4 X L14)
43/49/55LX341*
43/49/55LX540*
b
X8
(M4 X L16)
60LX341*
60LX540*
i
1
1
2
3
d
4
5
c + d
c
/ b
c + d
6
a/ b
a
H/P OUT
2 (MHL)
IN
USB IN
2
A-1
LX341*
A
B
H/P OUT
2 (MHL)
IN
1
2
A-2
LX540*
B
LAN
IN
(MHEG/SERVICE)
1
EXTERNAL
SPEAKER OUT
OPTICAL
DIGITAL
AUDIO OUT
AV
(RGB)
RS-232C IN
(CONTROL & SERVICE)
AUDIO IN
(COMPONENT/RGB/DVI)
LNB
Satellite
COMPONENT
IN
RGB IN (PC)
COMPONENT
IN
GND
RIGHT (
AUDIO IN
(COMPONENT/RGB/DVI)
AUDIO IN
(COMPONENT/RGB/DVI)
)
LEFT ( )
GND
L
VIDEO
R
AUDIO
ANTENNA/
CABLE IN
B
LAN
IN
(MHEG/SERVICE)
1
EXTERNAL
SPEAKER OUT
OPTICAL
DIGITAL
AUDIO OUT
AV
(RGB)
RS-232C IN
(CONTROL & SERVICE)
AUDIO IN
(COMPONENT/RGB/DVI)
LNB
Satellite
COMPONENT
IN
RGB IN (PC)
ANTENNA/
CABLE IN
3
4
5
1
2
3
4
A
F
E
B
D
G
C
43LX341C-GA
49LX341C-GA
55LX341C-GA
60LX341C-GA
A
x
B
x
C
(mm)
973 x 625 x 193
1106 x 697 x 220
1242 x 774 x 220
1363 x 844 x 294
A
x
E
x
F
(mm)
973 x 573 x 55.1
1106 x 647 x 55.1
1242 x 724 x 55.1
1363 x 792 x 57.1
D
(kg)
12.7
17.6
20.9
29.3
-
G
10.2
14.4
17.7
24.1
D
(kg)
43LX540S-GA
49LX540S-GA
55LX540S-GA
60LX540S-GA
A
x
B
x
C
(mm)
973 x 625 x 193
1106 x 697 x 220
1242 x 774 x 220
1363 x 844 x 294
A
x
E
x
F
(mm)
973 x 573 x 55.1
1106 x 647 x 55.1
1242 x 724 x 55.1
1363 x 792 x 57.1
D
(kg)
12.7
17.6
20.9
29.3
-
G
10.2
14.4
17.7
24.1
D
(kg)
OWNER’S MANUAL
Safety and Reference
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your
set and retain it for future reference.
www.lg.com
Safety instructions
ENGLISH
Please read these safety precautions carefully
before using the product.
WARNING
Do not place the TV and/or remote control in the following
environments:
• A location exposed to direct sunlight
• An area with high humidity such as a bathroom
• Near any heat source such as stoves and other devices that produce
heat
• Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
• An area exposed to rain or wind
• Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product
deformation.
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, fire ignition may break out.
Ensure the power cord does not come into contact with hot objects such
as a heater. This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
Do not place the product where it might be exposed to dust. This may
cause a fire hazard.
Bend antenna cable between inside and outside building to prevent
rain from flowing in. This may cause water damaged inside the Product
and could give an electric shock.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
fire hazard.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or wipe
dust off. You may be electrocuted due to excess moisture.
Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in fire due to over-heating.
2
Des
ENGLISH
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire
into the product, or inflammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, fire or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
icca
nt
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suffocation. Keep it out of
the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
Do not put or store inflammable substances near the product. There is a
danger of combustion/explosion or fire due to careless handling of the
inflammable substances.
3
ENGLISH
If any of the following occur, unplug the product immediately and
contact your local service centre.
• The product has been impacted by shock
• The product has been damaged
• Foreign objects have entered the product
• The product produced smoke or a strange smell
This may result in fire or electric shock.
Never Disassemble the AC adapter or power cord.
This may result in fire or electric shock.
CAUTION
Install the product where no radio wave occurs.
Unplug the TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause fire hazard
and insulation deterioration can cause electric leakage/shock/fire.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
Do not install the product on places such as unstable shelves or inclined
surfaces. Also avoid places where there is vibration or where the
product cannot be fully supported. Otherwise, the product may fall or
flip over, which may cause injury or damage to the product.
If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise, this may result in electric shock or fire.
If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
Only use an authorized AC adapter and power cord approved by LG
Electronics.
Otherwise, this may result in fire, electric shock, malfunction or product
deformation.
4
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), fix
it carefully so as not to drop.
Only use the attachments / accessories specified by the manufacturer.
When connecting external devices such as video game consoles, make
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Do not turn the product On/Off by plugging-in or unplugging the power
plug to the wall outlet. (Do not use the power plug for switch.) It may
cause mechanical failure or could give an electric shock.
Only use the specified type of battery. This could cause damage to the
remote control.
Please follow the installation instructions below to prevent the product
from overheating.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
ENGLISH
When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may create a
fire hazard or an electric shock hazard.
• The distance between the product and the wall should be more
than 10 cm.
• Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
• Do not install the product on a carpet or cushion.
• Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open fireplace and electric heaters.
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its
sensor.
Signal from Remote Control can be interrupted due to external/internal
lighting eg Sunlight, fluorescent lighting. If this occurs turn off lighting
or darken viewing area.
Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not affect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet. This may cause
a fire hazard.
5
ENGLISH
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
When moving the product, make sure you turn the power off first. Then,
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
Do not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may cause damage
to screen.
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Avoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this unit
by SWITCH.
If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
When unplugging the cable, grab the plug and unplug it, by pulling at
the plug.
The panel is a high technology display product with resolution of two
million to six million pixels. You may see tiny black dots and/or brightly
coloured dots (red, blue or green) at a size of 1 ppm on the panel. This
does not indicate a malfunction and does not affect the performance
and reliability of the product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
6
Contact the service centre once a year to clean the internal parts of the
product.
Accumulated dust can cause mechanical failure.
Preparing
Displaying a still image (e.g., broadcasting channel logo, on-screen
menu, scene from a video game) for a prolonged time may cause
damage to the screen, resulting in retention of the image, which is
known as image sticking. The warranty does not cover the product
for image sticking. Avoid displaying a fixed image on your television’s
screen for a prolonged period. Also, if you watch the TV at a ratio of 4:3
for a long time, image sticking may occur on the borders of the panel.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
NOTE
• Image shown may differ from your TV.
• Your TV’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
• The available menus and options may differ from the input source
or product model that you are using.
• New features may be added to this TV in the future.
• The TV can be placed in standby mode in order to reduce the power
consumption. And the TV should be turned off if it will not be
watched for some time, as this will reduce energy consumption.
• The energy consumed during use can be significantly reduced if the
level of brightness of the picture is reduced, and this will reduce
the overall running cost.
• The items supplied with your product may vary depending on the
model.
• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
• For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
Generated Sound
“Cracking” noise: A cracking noise that occurs when watching or turning
off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product.
This generated sound does not affect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
ENGLISH
You may find different brightness and color of the panel depending on
your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI Cable Types)
-- High-Speed HDMI®/TM cable (3 m or less)
-- High-Speed HDMI®/TM cable with Ethernet (3 m or less)
CAUTION
• Do not use any unapproved items to ensure the safety and product
life span.
• Any damage or injuries caused by using unapproved items are not
covered by the manufacturer’s warranty.
• Some models have a thin film attached on to the screen and this
must not be removed.
• When attaching the stand to the TV set, place the screen facing
down on a cushioned table or flat surface to protect the screen
from scratches.
• Make sure that the screws are fastened completely. (If they are
not fastened securely enough, the TV may tilt forward after being
installed.) Do not use too much force and over tighten the screws;
otherwise screw may be damaged and not tighten correctly.
7
ENGLISH
Separate purchase
Lifting and moving the TV
Separate purchase items can be changed or modified for quality
improvement without any notification. Contact your dealer to buy
these items. These devices only work with certain models. The model
name or design may be changed depending on the upgrade of product
functions, manufacturer’s circumstances or policies.
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
(Depending on model)
LED Clock
LEC-003
AN-WF500
Wi-Fi/Bluetooth Dongle
LG Audio Device
• It is recommended to move the TV in the box or packing material
that the TV originally came in.
• Before moving or lifting the TV, disconnect the power cord and
all cables.
• When holding the TV, the screen should face away from you to
avoid damage.
• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
Maintenance
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the
product lifespan.
• Make sure to turn the power off and disconnect the power cord and
all other cables first.
• When the TV is left unattended and unused for a long time,
disconnect the power cord from the wall outlet to prevent possible
damage from lightning or power surges.
• When transporting a large TV, there should be at least 2 people.
• When transporting the TV by hand, hold the TV as shown in the
following illustration.
Screen, frame, cabinet and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and
soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in
clean water or a diluted mild detergent. Then wipe immediately with
a dry cloth.
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not push, rub, or hit the screen surface with your fingernail or a
sharp object, as this may result in scratches and image distortions.
• Do not use any chemicals as this may damage the product.
• Do not spray liquid onto the surface. If water enters the TV, it may
result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
8
• When transporting the TV, do not expose the TV to jolts or
excessive vibration.
• When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
• Do not apply excessive pressure to cause flexing /bending of frame
chassis as it may damage screen.
• When handling the TV, be careful not to damage the protruding
joystick button. (Depending on model)
CAUTION
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not move the TV by holding the cable holders, as the cable
holders may break, and injuries and damage to the TV may occur.
Mounting on a table
(Image shown may differ from your TV.)
(Image shown may differ from your TV.)
You can simply operate the TV functions, pressing or moving the joystick
button up, down, left or right.
1 Lift and tilt the TV into its upright position on a table. ENGLISH
Using the joystick button
• Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
Joystick Button
10 cm
10 cm
10 cm
10 cm
Basic Functions
2 Connect the power cord to a wall outlet.
CAUTION
When the TV is turned off, place
Power On
your finger on the joystick button
and press it once and release it.
When the TV is turned on, place
your finger on the joystick button
and press it once for a few seconds
Power Off
and release it. (However, if the
Menu button is on the screen,
pressing and holding the joystick
button will let you exit the Menu.)
If you place your finger over the
Volume
joystick button and move it left or
Control
right, you can adjust the volume
level you want.
If you place your finger over the
Programmes joystick button and move it up or
Control
down, you can scrolls through the
saved programmes you want.
Adjusting the Menu
When the TV is turned on, press the joystick button one time. You can
adjust the Menu items moving the joystick button up, down, left or
right.
Turns the power off.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
• Do not place the TV near or on sources of heat, as this may result in
fire or other damage.
WARNING
• If a television is not positioned in a sufficiently stable location,
it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple
precautions such as:
»» Using cabinets or stands recommended by the
manufacturer of the television.
»» Only using furniture that can safely support the
television.
»» Ensuring the television is not overhanging the edge of
the supporting furniture.
»» Not placing the television on tall furniture (for
example, cupboards or bookcases) without anchoring
both the furniture and the television to a suitable
support.
»» Not standing the televisions on cloth or other materials
placed between the television and supporting
furniture.
»» Educating children about the dangers of climbing on
furniture to reach the television or its controls.
Accesses the main menu.
NOTE
• When your finger over the joystick button and push it to the up,
down, left or right, be careful not to press the joystick button. If you
press the joystick button first, you may not be able to adjust the
volume level and saved programmes.
9
Adjusting the angle of the TV to suit
view
B type)
(Depending on model)
ENGLISH
Swivel 20 degrees to the left or right and adjust the angle of the TV to
suit your view.
20˚
20˚
CAUTION
• When adjusting the angle of the product, watch out for your
fingers.
-- Personal injury may occur if hands or fingers are pinched. If the
product is tilted too much, it may fall, causing damage or injury.
2-Screws for Stand Fixing,
2-Washers for Stand Fixing,
2-Nuts for Stand Fixing
(Supplied with TV)
Stand
Attaching the TV to a desk
(Depending on model)
Desk
The TV should be attached to a desk so it cannot be pulled in a forward/
backward direction, potentially causing injury or damaging the product.
A type)
Using the kensington security
system
(This is not available for all models.)
• Image shown may differ from your TV.
The Kensington security system connector is located at the rear of the
TV. For more information of installation and using, refer to the manual
provided with the Kensington security system or visit http://www.
kensington.com. Connect the Kensington security system cable between
the TV and a table.
4-Screws
(Not supplied with TV)
Stand
Desk
NOTE
• Screw : M5 x L (*L: Table depth + 8~10 mm)
ex) Table depth: 15 mm, Screw: M5 x L25
10
Securing the TV to a wall
(This feature is not available for all models.)
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
32LX33**
32/43LX54**
43LX34**
VESA (A x B)(mm) 200 x 200
Standard screw
M6
Number of screws 4
Model
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
CAUTION
• Make sure that children do not climb on or hang on the TV.
49/55LX34**
49/55LX54**
300 x 300
M6
4
Wall mount
bracket
LSW240B
MSW240
LSW350B
MSW240
Model
60LX34**
60LX54**
42LX33**
42LX53**
300 x 300
M6
4
400 x 400
M6
4
LSW440B
MSW240
VESA (A x B)(mm)
Standard screw
Number of screws
Wall mount
bracket
LSW350B
ENGLISH
Separate purchase(Wall Mounting Bracket)
NOTE
• Use a platform or cabinet that is strong and large enough to
support the TV securely.
• Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
A
B
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing fixed wall mounts.
10 cm
10 cm
10 cm
10 cm
11
CAUTION
ENGLISH
• Disconnect the power first, and then move or install the TV.
Otherwise electric shock may occur.
• Remove the stand before installing the TV on a wall mount by
performing the stand attachment in reverse.
• If you install the TV on a ceiling or slanted wall, it may fall and
result in severe injury. Use an authorised LG wall mount and
contact the local dealer or qualified personnel.
• Do not over tighten the screws as this may cause damage to the TV
and void your warranty.
• Use the screws and wall mounts that meet the VESA standard. Any
damages or injuries by misuse or using an improper accessory are
not covered by the manufacturer’s warranty.
NOTE
• Use the screws that are listed on the VESA standard screw
specifications.
• The wall mount kit includes an installation manual and necessary
parts.
• The wall mount bracket is not provided. You can obtain additional
accessories from your local dealer.
• The length of screws may differ depending on the wall mount.
Make sure to use the proper length.
• For more information, refer to the manual supplied with the wall
mount.
• When installing the wall mounting bracket, use the adhesive
label provided. The adhesive label will protect the opening from
accumulating dust and dirt. (Only when the label is provided)
Provided Item
Adhesive label
12
• When attaching a wall mounting bracket to the TV, insert the wall
mount spacers into the TV wall mount holes to adjust the vertical
angle of the TV. (Only when the item of the following form is
provided)
Provided Item
Wall Mount Spacer
How to use Dual Lock™
Connections (notifications)
(Only when the item of the following form is provided)
(This feature is not available for all models.)
1 After removing the protection paper from the Dual LockTM, stick it to
the TV and the set-top box as shown.
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
ENGLISH
Fix the set-top box to the TV and use it when you want to.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
NOTE
Dual Lock™
2 Attach the set-top box to the TV by pressing the Velcro strips
together.
• The external device connection may differ from the model.
• Connect external devices to the TV regardless of the order of the
TV port.
• If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
• Refer to the external equipment’s manual for operating
instructions.
• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
• In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE
menu until the picture is clear.
• In PC mode, some resolution settings may not work properly
depending on the graphics card.
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
NOTE
• Please make sure no foreign substances exist on the surface of the
product, and then firmly attach the Dual Lock™.
• Before attaching the set-top box to the TV set, let the attached
Dual Lock™ dry for at least three days.
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal amplifier properly to
improve the image quality.
• If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
• An antenna cable and converter are not supplied.
• Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
13
Adapter connection
Speaker Output Setup
(Depending on model)
(Depending on model)
CAUTION
ENGLISH
• Please be sure to connect the TV to the AC-DC power adapter
before connecting the TV’s power plug to a wall power outlet.
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
EXTERNAL
SPEAKER OUT
• Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
cause damage to the TV and the PCMCIA card slot.
• If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
VOLUME
CONTROL
Euro scart connection
Control port for Speaker out
+
Transmits the video and audio signals from an external device to the
TV set. Connect the external device and the TV set with the euro scart
cable.
Output
Type
Current
input mode
Digital TV
DOWN
GND
RIGHT
AV1
(TV Out1)
Digital TV
LEFT
GND
Analogue TV, AV
Component
UP
-
(Depending on model)
Analogue TV
HDMI
1 TV Out : Outputs Analogue TV or Digital TV signals.
• Any Euro scart cable used must be signal shielded.
NOTE
• Use only with the 3 Pole 3.5mm Stereo Jack.
• Do not connect your headphones or earphones to the port for
connecting an external speaker.
Method of Volume control port
• Cable Spec.
Each Up / Down pin is
pulled to 3.3V with CPU
GPIO.
GND / Up / Down
CPU detects transition
from 3.3V to GND level
for volume control.
14
Remote control
Network setup
Wired network connection
(Depending on model)
This TV can be connected to a Pro:Centric server via the LAN port. After
making the physical connection, the TV needs to be set up for network
communication. Connect the LAN port of the Modem or Router from
Pro:Centric server to the LAN port on the TV.
ENGLISH
(Depending on model)
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
CAUTION
LAN
(MHEG &
SERVICE)
or
(MHEG / SERVICE)
or
• Do not mix old and new batteries, as this may damage the remote
control.
• In Analogue TV and some countries, some remote control buttons
may not work.
LAN
Make sure to point the remote control toward the remote control sensor
on the TV.
Broadband Modem
Pro:CentricServer
A
Router
Broadband Modem
Pro:CentricServer
B
CAUTION
• Do not connect a modular phone cable to the LAN port.
• Since there are various connection methods, please follow the
specifications of your telecommunication carrier or internet service
provider.
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
A
(POWER) Turns the TV on or off.
Selects Radio, TV and DTV programme.
Recalls your preferred subtitle in digital mode.
Selects an AV mode.
Resizes an image.
Changes the input source.
Number buttons Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
15
B
ENGLISH
Adjusts the volume level.
Accesses your favourite programme list.
Shows programme guide.
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
A
C
B
D
C
Teletext buttons (
) These buttons are used for
teletext.
Views the information of the current programme and
screen.
Accesses the main menus.
Accesses the Quick menus.
Selects menus or options and confirms your input.
Navigation buttons (up/down/left/right) Scrolls through
menus or options.
Returns to the previous level.
Clears on-screen displays and returns to TV viewing.
D
Accesses the AV devices connected with the HDMI
cable through HDMI-CEC. Opens the SIMPLINK menu.
By pressing the AD button, audio descriptions function will be
enabled.
Control buttons (
) Controls the MY MEDIA
menus or the SIMPLINK compatible devices (USB, SIMPLINK).
Coloured buttons These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
16
A
(POWER) Turns the TV on or off.
Adjusts the brightness of the screen to reduce
energy consumption.
Selects an AV mode.
Changes the input source.
Selects Radio, TV and DTV programme.
Number buttons Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
B
Adjusts the volume level.
Accesses your favourite programme list.
Resizes an image.
Mutes all sounds.
Scrolls through the saved programmes.
PAGE Moves to the previous or next screen.
Licenses
ENGLISH
C
Supported licenses may differ by model. For more information about
licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
D
The terms HDMI and HDMI High-Definition Multimedia interface,
and the HDMI logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
C
Shows programme guide.
Displays and removes hotel interactive menu.
Views the information of the current programme and
screen.
Navigation buttons (up/down/left/right) Scrolls through
menus or options.
Selects menus or options and confirms your input.
Accesses the main menus.
(BACK) Returns to the previous level.
Clears on-screen displays and return to TV viewing.
Coloured buttons These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
D
Teletext buttons (
) These buttons are used for
teletext.
Recalls your preferred subtitle in digital mode.
Control buttons (
) Controls the MY MEDIA
menus or the SIMPLINK compatible devices (USB, SIMPLINK).
Accesses the AV devices connected with the HDMI
cable through HDMI-CEC. Opens the SIMPLINK menu.
Accesses the Quick menus.
By pressing the AD button, audio descriptions function will be
enabled.
Sets the alarm function. (depending on model)
This DivX Certified® device has passed rigorous testing to ensure it
plays DivX® video.
To play purchased DivX movies, first register your device at vod.divx.
com. Find your registration code in the DivX VOD section of your
device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX,
LLC and are used under license.
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274.”
17
Open source software
notice information
ENGLISH
To obtain the source code under GPL, LGPL, MPL and other open source
licenses, that is contained in this product, please visit http://opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date
on which you purchased the product.
Troubleshooting
The software version can be updated for improvement in performance.
Customer needs to ensure the compatibility of customer’s equipment
with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Cannot control the TV with the remote control.
• Check the remote control sensor on the product and try again.
• Check if there is any obstacle between the product and the remote
control.
• Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
• Check if the product is turned on.
• Check if the power cord is connected to a wall outlet.
• Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
• Check the power control settings. The power supply may be
interrupted.
• Check if the Automatic Standby(Depending on model) / Sleep
Timer / Off Time is activated in the TIME settings.
• If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
When connecting to the PC (RGB/HDMI/DVI), ‘No signal’ or ‘Invalid
Format’ is displayed.
• Turn the TV off/on using the remote control.
• Reconnect the RGB/HDMI cable.
• Restart the PC with the TV on.
18
Software download information
ENGLISH
• Use this information for LX540S, LX530S series.
You can download the SuperSign Software and manual from LG Electronics website.
Visit https://www.lgecommercial.com/digital-signage/support/download/supersign for Software & https://www.lgecommercial.com/digital-signage/support/download/supersign for manual.
Software : SuperSign W_Lite_Server_vX.X.X_Setup.zip SuperSign C_vX.X.X_Setup.zip SuperSign W_Editor_vX.X.X_Setup.zip SuperSign W_Player_vX.X.X_Setup.zip
Manual : SuperSign W_Lite_Server_vX.X.X_Manual.zip SuperSign C_vX.X.X_Manual.zip SuperSign W_Editor_vX.X.X_Manual.zip SuperSign W_Player_vX.X.X_Manual.zip
Specifications
CI Module Size (W x H x D)
Environment
condition
100.0 mm x 55.0 mm x 5.0 mm
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Satellite Digital TV
(Depend on Country)
Digital TV
(Depend on Country)
Television system
DVB-S/S2
DVB-T/T2
DVB-C
Programme coverage
VHF, UHF
C-Band, Ku-Band
VHF, UHF, CATV
Maximum number of
storable programmes
6,000
1,500
External antenna impedance
Analogue TV
(Depend on Country)
PAL B/G, PAL D/K, PAL-I,
SECAM-B/G, SECAM D/K,
NTSC-M
75 Ω
19
HDMI/DVI-DTV supported mode
ENGLISH
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720 x 480
31.469
31.5
59.94
60
720 x 576
31.25
50
1280 x 720
37.5
44.96
45
50
59.94
60
1920 x 1080
28.125
33.75
33.72
56.250
67.50
67.432
27.00
26.973
33.75
33.716
50.00
60.00
59.94
50.00
60.00
59.94
24.00
23.976
30.00
29.976
(Only LX33**, LX34**,LX540S, LX530S)
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
640 x 480
31.469
59.94
(Only LX33**, LX34**, LX53**, LX54**)
Resolution
1
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
31.468
31.469
31.469
37.879
48.363
54.348
47.712
70.09
70.08
59.94
60.31
60.00
60.053
60.015
63.981
60.020
67.50
60.00
640 x 350
720 x 400
640 x 480
800 x 600
1024 x 768
1152 x 864
1360 x 768
1280 x 1024
(FHD only)
1920 x 1080
(FHD only)
1 : Only LX341*, 42LX330*, LX54**, LX530S
Component ports on the TV
Video output ports on
DVD player
60.31
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
800 x 600
37.879
1024 x 768
48.363
60.00
Signal
Component
1152 x 864
54.348
60.053
480i / 576i
O
1360 x 768
47.712
60.015
480p / 576p
O
720p / 1080i
O
1080p
O
(Only 50 Hz / 60 Hz)
1280 x 1024
(FHD only)
63.981
60.020
1920 x 1080
(FHD only)
66.587
59.934
1920 x 1080
(FHD only)
67.50
60.00
1 : Only LX341*, 42LX330*, LX540S, LX530S
20
(Use HDMI IN 1 for PC mode)
Component port connecting
information
RGB-PC supported mode
1
HDMI/DVI-PC supported mode
Supported video formats
• File type : mp3
[Bit rate] 32 Kbps - 320 Kbps
[Sample freq.] 16 kHz - 48 kHz
[Support] MPEG1, MPEG2, Layer2 , Layer3
• File Type : AAC
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] ADIF, ADTS
• File Type : M4A
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] MPEG-4
• File Type : WMA
[Bit rate] 128 Kbps ~ 320 Kbps
[Sample freq.] 8 kHz ~ 48 kHz
[Support] WMA7, WMA8, WMA9 Standard
• File Type : WMA 10 Pro
[Bit rate] ~ 768 Kbps
[Channel / Sample freq.]
M0 : up to 2 Channel @ 48 kHz
(Except LBR mode),
M1 : up to 5.1 Channel @ 48 kHz,
M2 : up to 5.1 Channel @ 96 kHz
[Support] WMA 10 Pro
• File Type : OGG
[Bit rate] Free Format
[Sample freq.] ~ 48 kHz
[Support] OGG Vorvis
ENGLISH
• Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p)
• .asf, .wmv
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XViD, H.264/AVC, VC1(WMV3, WVC1), MP43
[Audio] WMA Standard, WMA9(Pro), MP3, AAC, AC3, MP3, 3D WMV
Single Stream.
• divx, .avi
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XViD, H.264/AVC
[Audio] HE-AAC, LPCM, ADPCM, MPEG- 1 Layer I, MPEG-1 Layer II,
Dolby Digital, MPEG-1 Layer III (MP3), *DTS
• .ts, .trp, .tp, .mts, .m2ts
[Video] H.264/AVC, MPEG-2, AVS, VC1
[Audio] MPEG-1 Layer I, MPEG-1 Layer II, MPEG-1 Layer III (MP3),
Dolby Digital, Dolby Digital Plus, AAC, HE-AAC, *DTS
• .vob
[Video] MPEG-1, MPEG-2
[Audio] Dolby Digital, MPEG-1 Layer I, MPEG- 1 Layer II, DVD-LPCM
• .mp4, .m4v, .mov
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XVID, H.264/AVC
[Audio] AAC, MPEG-1 Layer III (MP3), *DTS
• .mkv
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,
XVID, H.264/AVC
[Audio] HE-AAC, Dolby Digital, MPEG-1 Layer III (MP3), *DTS, LPCM
• motion JPEG
[Video] MJPEG
[Audio] LPCM, ADPCM
• .mpg, .mpeg, .mpe
[Video] MPEG-1, MPEG-2
[Audio] MPEG-1 Layer I, MPEG-1 Layer II, Dolby Digital, LPCM
• dat
[Video] MPEG-1, MPEG-2
[Audio] MP2
• flv
[Video] Sorenson H.263, H.264/AVC
[Audio] MP3, AAC, HE-AAC
• *rm, *rmvb
[Video] RV30, RV40
[Audio] Dolby Digital, AAC, HE-AAC, RA6(Cook)
• 3gp, 3gp2
[Video] H.264/AVC, MPEG-4 Part2
[Audio] AAC, AMR(NB/WB)
• *DTS / *rm / *rmvb : Depending on model
Supported audio formats
21
Supported photo formats
ENGLISH
• Category : 2D (jpeg, jpg, jpe)
[Available file type] SOF0: Baseline,
SOF1 : Extend Sequential,
SOF2 : Progressive
[Photo size] Minimum : 64 x 64,
Maximum : Normal Type: 15360 (W) x 8640 (H),
Progressive Type : 1920 (W) x 1440 (H)
• Category : BMP
[Photo size] Minimum : 64 x 64, Maximum : 9600 x 6400
• Category : PNG
[Available file type] Interlace, Non-Interlace
[Photo size] Minimum : 64 x 64, Maximum : Interlace : 1200 x 800,
Non-Interlace : 9600 x 6400
• BMP and PNG format files may be slower to display than JPEG.
22
Record the model number and serial number
of the TV.
Refer to the label on the back cover and
quote this information to your dealer when
requiring any service.
MODEL
SERIAL
(Only DTV)
IR CODES
yy This feature is not available for all models.
Function
08
F0
39
91
79
0B
10-19
53
1A
(POWER)
TV/RAD
SUBTITLE
AD
RATIO
INPUT
Number Key 0-9
LIST
Q.VIEW
Note
Remote control Button (Power
On/Off)
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
02
+
Remote control Button
03
FAV
GUIDE
Remote control Button
Remote control Button
20
21
MUTE
P ꕌ / PAGE ꕌ/
PAGE
P ꕍ / PAGE ꕍ /
PAGE
TEXT
T.OPT(T.Option)
43
SETTINGS
Remote control Button
45
Q.MENU
Remote control Button
AA
Remote control Button
5B
INFO
EXIT
28
BACK
Remote control Button
44
Remote control Button
40
OK
^
41
v
Remote control Button
07
<
Remote control Button
06
>
Remote control Button
1E
AB
09
00
01
Remote control Button
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
B1
Remote control Button
B0
Remote control Button
BA
yy
Remote control Button
8E
8F
7E
30
E8
0C
►►
◄◄
SIMPLINK
AV MODE
ALARM
PORTAL
ENERGY
SAVING
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
95
ENGLISH
Code
(Hexa)
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
1
EXTERNAL CONTROL
DEVICE SETUP
Type of Connector : D-Sub 9-Pin
Male
1
5
ENGLISH
RS-232C Setup
• Image shown may differ from your TV.
Connect the RS-232C (serial port) input jack to an external control
device (such as a computer or an A/V control system) to control the
product’s functions externally.
Connect the serial port of the control device to the RS-232C jack on the
product back panel.
NOTE
• RS-232C connection cables are not supplied with the product.
RS-232C IN
(CONTROL & SERVICE)
(*Not Provided)
2
6
No.
9
Pin name
1
3.5 V
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
No Connection (5 V available in LX54*H)
8
No Connection
9
No Connection (12 V available in LX54*H)
Command Reference List
RS-232C Configurations
(Depending on Model)
7-Wire Configurations
(Standard RS-232C cable)
PC
TV
RXD
TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9
3-Wire Configurations
(Not standard)
PC
TV
RXD
TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
D-Sub 9
Set ID
Set ID number. “Real Data Mapping”.
Press SETTINGS or HOME to access the main menus.
Press the Navigation buttons to scroll to OPTION and press OK.
Press the Navigation buttons to scroll to Set ID and press OK.
Scroll left or right to select a set ID number and select Close. The
adjustment range is 1-99.
When you are finished, press EXIT.
1
2
3
4
5
Communication Parameters
• • • • • • Baud rate: 9600 bps (UART)
Data length: 8 bits
Parity : None
Stop bit: 1 bit
Communication code: ASCII code
Use a crossed (reverse) cable.
COMMAND2
01. Power
k
a
00 to 01
02. Aspect Ratio
k
c
(See p. 4)
03. Screen Mute
k
d
(See p. 5)
04. Volume Mute
k
e
00 to 01
05. Volume
Control
k
f
00 to 64
06. Contrast
k
g
00 to 64
07. Brightness
k
h
00 to 64
08. Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 32
11. OSD Select
k
l
00 to 01
k
m
00 to 01
k
t
00 to 64
x
u
00 to 64
15. Energy Saving
j
q
(See p. 6)
16. Auto Configuration
j
u
01
17. Equalize
j
v
(See p. 7)
m
a
(See p. 7)
m
b
00 to 01
m
c
(See p. 7)
m
g
00 to 64
x
b
(See p. 8)
12. Remote
Control
Lock Mode
13. Balance
14. Colour
Temperature
18. Tune Command
19. Programme
Add/Skip
20. Key
21. Control Back
Light
22. Input select
(Main)
ENGLISH
DATA
(Hexadecimal)
COMMAND1
NOTE
• During USB operations such as DivX or EMF, all commands except
Power(ka) and Key(mc) are not executed and treated as NG.
3
Transmission / Receiving Protocol
(Depending on Model)
ENGLISH
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
01. Power (Command: k a)
►► To control Power On/Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
[Command 1] : First command to control the TV.(j, k, m or x)
►► To Show TV is Power On/Off.
[Command 2] : Second command to control the TV.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
[Set ID] : You can adjust the set ID to choose desired monitor ID number
in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’,
every connected set is controlled. Set ID is indicated as decimal (1 to 99)
on menu and as Hexa decimal (0x0 to 0x63) on transmission/receiving
protocol.
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data based on this
format, Acknowledgement data feed back presents status about
each function.
[Data] : To transmit command data.Transmit ‘FF’ data to read status of
command.
* OK Ack., Error Ack. and other message may display on the screen
when TV is power On.
[Cr] : C arriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when
receiving normal data. At this time, if the data is data read mode, it
indicates present status data. If the data is data write mode, it returns
the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when
receiving abnormal data from non-viable functions or communication
errors.
Data 00 : Illegal Code
4
02. Aspect Ratio (Command: k c)
(Main Picture Size)
►► To adjust the screen format. (Main picture format) You can also
adjust the screen format using the Aspect Ratio in the Q.MENU. or
PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : N ormal screen (4:3)
02 : Wide screen (16:9)
04 : Zoom
06 : O riginal
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p 24 Hz
/ 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i, 1080p 50 Hz / 60
Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital.
03. Screen Mute (Command: k d)
07. Brightness (Command: k h)
►► To select screen mute on/off.
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen
Display(OSD). But, in case of Screen mute on, TV will not display OSD.
04. Volume Mute (Command: k e)
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume buttons on remote
control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Transmission [k][h][ ][Set ID][ ][Data][Cr]
ENGLISH
Data
Data Min : 0 0 to Max : 64
* Refer to Real data mapping.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
08. Colour (Command: k i)
►► To adjust the screen Colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 0 to Max : 64
* Refer to Real data mapping.
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to Real data mapping.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 0 0 to Max : 64
* Refer to Real data mapping.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 0 0 to Max : 32
* Refer to Real data mapping.
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 0 0 to Max : 64
* Refer to Real data mapping.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
5
11. OSD Select (Command: k l)
15. Energy Saving (Command: j q)
►► To select OSD (On Screen Display) on/off when controlling remotely.
►► To reduce the power consumption of the TV. You can also adjust
Energy Saving in PICTURE menu.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
ENGLISH
Data 00 : OSD off
Transmission [j][q][ ][Set ID][ ][Data][Cr]
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
Power Saving
Function
7
6
5
4
0
0
0
0
0
0
0
0
0
0
* If you are not using the remote control, use this mode. When main
power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by power
on key of IR & Local Key.
12. Remote control lock mode (Command: k m)
Data 00 : Lock off
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
Description
3
2
1
0
Low
Power
0
0
0
0
Off
0
Low
Power
0
0
0
1
Minimum
0
0
Low
Power
0
0
1
0
Medium
0
0
0
Low
Power
0
0
1
1
Maximum
0
0
0
0
Low
Power
0
1
0
1
Screen Off
0
0
0
0
Low
Power
0
1
0
0
Auto
►► To lock the front panel controls on the monitor and remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Level
►► 'Auto' is available in TV that supports 'Intelligent Sensor'.
13. Balance (Command: k t)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data L : 00 to R : 64
* Refer to Real data mapping.
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
16. Auto Configure (Command: j u) (Only RGB support model)
►► To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set
14. Colour Temperature (Command: x u)
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Warm: 00 to Cool:64
* Refer to Real data mapping.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
6
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. Equalizer (Command : j v)
19. Programme Add/Skip (Command: m b)
►► To adjust equalize.
►► To set skip status for the current Programme.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
Transmission [m][b][ ][Set ID][ ][Data][Cr]
LSB
0
0
0
0
0
0
0
Data 00 : Skip
0
ENGLISH
MSB
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
Data
Frequency
7 6 5
Frequency
4 3 2 1 0
Step
0 0 0
1st Band
0 0 0 0 0
0(decimal)
0 0 1
2nd Band
0 0 0 0 1
1(decimal)
0 1 0
3rd Band
... ... ... ... ...
...
0 1 1
4th Band
1 0 0 1 1
19(decimal)
1 0 0
5th Band
1 0 1 0 0
20(decimal)
20. Key (Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data
IR CODES
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Ack [v][ ][Set ID][ ][OK/NG][Data][x]
21. Control Back Light (Command: m g)
►► To control the backlight.
18. Tune Command (Command: m a)
►► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Data 00 : High channel data
Data 01 : Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data 02 : [Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
[Satellite]
0x40 : DTV Main
0x50 : Radio Main
Channel data range
Min: 00 Max: 270F (0 to 9999)
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 to Max: 7DH
7
22. Input select (Command: x b)
(Main Picture Input)
* Real data mapping
►► To select input source for main picture.
ENGLISH
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
LSB
0
0
0
0
External Input
0
0
Input Number
External Input
A:
Step 10 (Set ID 10)
0
F:
Step 15 (Set ID 15)
10 :
Step 16 (Set ID 16)
64 :
Step 100
6E :
Step 110
73 :
Step 115
74 :
Step 116
CF :
Step 199
FE :
Step 254
FF :
Step 255
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
8
Step 0
Structure
MSB
0
00 :
Download PDF

advertising