LG | 37LD650H | LG 47LD650H Owner’s Manual

ENGLISH
OWNER’S MANUAL
LED LCD TV/LCD TV
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
Separate purchase
Wall Mounting Bracket
LSW100B or
LSW100BG
(32LD6***, 32LV3***)
LSW200B or
LSW200BG
(37/42/47LD6***, 37LV3***)
LSW400B or
LSW400BG
(42/47LV3***)
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
CONTENTS
LCD TV Models : 32/37/42/47LD6***.............. A-1
LED LCD TV Models : 32/37/42/47LV3***..... A-13
EXTERNAL EQUIPMENT SETUP
Antenna Connection.............................................1
Connecting with a Component cable...................2
Connecting with an HDMI cable..........................3
Connecting with an HDMI to DVI cable...............4
Connecting with a Euro Scart cable....................5
Usb setup.............................................................6
Connecting with AN RF Cable.............................6
Connecting with a D-sub 15 pin cable.................7
Speaker output Setup..........................................7
Insertion of A CI Module.......................................8
Headphone Setup................................................8
Digital audio out Setup.........................................9
Supported Display Resolution............................10
Screen Setup for PC mode................................12
Network setup....................................................16
WATCHING TV / PROGRAMME CONTROL
Turning on the TV..............................................17
Initializing Setup ................................................17
Programme Selection.........................................17
Volume Adjustment............................................17
Quick Menu........................................................18
On Screen Menus Selection and adjustment....19
Auto programme tuning ....................................21
Manual programme Tuning................................22
Programme Edit ................................................26
Booster...............................................................28
CI [Common Interface] Information....................29
Selecting the Programme List............................30
Input List.............................................................31
Input Label.........................................................32
Data Service.......................................................33
SIMPLINK...........................................................34
AV Mode.............................................................38
Initializing(Reset to original factory settings).....39
TO USE A USB DEVICE
When connecting a USB device........................40
Movie list............................................................42
Photo list.............................................................53
Music list.............................................................63
Extra Contents...................................................72
DivX Registration Code......................................73
Deactivation........................................................74
CONTENTS
PREPARATION
EPG(ELECTRONIC PROGRAMME
GUIDE)(IN DIGITAL MODE)
Switch on/off EPG..............................................76
Select a programme...........................................76
Button Function in NOW/NEXT Guide Mode....76
Button Function in 8 Day Guide Mode..............77
Button Function in Date Change Mode.............78
Button Function in Extended Description Box...78
PICTURE CONTROL
Picture Size (Aspect Ratio) Control...................79
Picture Wizard....................................................81
Energy Saving....................................................82
Preset Picture Settings......................................83
Manual Picture Adjustment................................84
Picture Improvement Technology.......................86
Expert Picture Control........................................87
Picture Reset......................................................90
Trumotion...........................................................91
Demo Mode........................................................92
Power Indicator..................................................93
I
CONTENTS
SOUND & LANGUAGE CONTROL
CONTENTS
Auto Volume Leveler..........................................94
Clear Voice II......................................................95
Preset Sound Settings-Sound Mode.................96
Sound Setting Adjustment -User Mode.............97
Infinite Sound.....................................................97
Balance..............................................................98
DTV Audio Setting (in digital mode only)...........99
Selecting Digital Audio out...............................100
Audio Reset......................................................101
Audio Description (In digital mode only)..........102
I/II
Stereo/Dual Reception (In Analogue Mode Only)...103
NICAM Reception (In Analogue Mode Only)...104
Speaker Sound Output Selection....................104
On-Screen Menu Language / Country Selection... 105
Language Selection.........................................106
TIME SETTING
Clock Setup......................................................108
Auto on/off time setting....................................109
Sleep Timer setting..........................................110
Alarm setting.................................................... 111
Automatic Standby...........................................112
PARENTAL CONTROL / RATINGS
Set Password & Lock System.........................113
Block Programme.............................................114
Parental Control (In Digital Mode only)............115
External Input Blocking....................................116
Key Lock..........................................................117
II
TELETEXT
Switch on/off ...................................................118
SIMPLE Text....................................................118
TOP Text..........................................................119
FASTEXT.........................................................119
Special Teletext Functions...............................120
DIGITAL TELETEXT
Teletext within Digital Service..........................121
Teletext in Digital Service.................................121
APPENDIX
Troubleshooting................................................122
Maintenance.....................................................124
Product Specifications ....................................125
IR Codes..........................................................129
External Control Device Setup.........................130
Open source software notice...........................137
PREPARATION
LCD TV MODELS : 32/37/42/47LD6***
Ensure that the following accessories are included with your TV. If an accessory is missing, please
contact the dealer where you purchased the TV.
■■ Image shown may differ from your TV.
EN
ER
GY
AV
SAVI
NG
hi
7pq
rs
LIS
T
ID
E
MU
DE
TE
RA
TIO
LE
TE
PO
RT
AL
OK
AR
8 tu
UM
DE
INPU
2 ab
c
l
9 wxy
6m
3d
TV
RA /
D
ef
no
z
Q.V
/N
RK
MO
T
5 jk
v
[
0
CH
MA
GU
1.,;@
4g
PREPARATION
ACCESSORIES
IEW
P
E
A
G
P
IN
FO
ME
NU
BA
CK
EX
IT
Q.M
EN
U
AD
ALA
RM
Owner’s Manual
Batteries
(AAA)
Remote Control
Protection cover
Power Cord
Only 32/37/42LD6***
x8
(M4x20)
Bolts for stand assembly
1-screw for stand fixing
Plug in type Holder
Cable Holder
This item is not included for all models.
*L
ightly wipe any stains
or fingerprints on the
surface of the TV with
the polishing cloth.
Ferrite Core
(This item is not included
for all models.)
Protective Bracket and
Bolt for Power Cord
(This feature is not
available for all models.)
Polishing Cloth
Do not use excessive
Polishing cloth for force. This may cause
use on the screen. scratching or discolouration.
Use of ferrite core (This feature is not available for all models.)
Ferrite core can be used to reduce the electromagnetic
wave when connecting the power cord.
The closer the location of the ferrite core to the power
plug, the better it is.
Install the power plug closely.
A-1
PREPARATION
FRONT PANEL CONTROLS
NOTE
PREPARATION
►TV
► can be placed in standby mode in order to reduce the power consumption. And TV should be
switched off using the power switch on the TV if it will not be watched for some time, as this will
reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of
brightness of the picture is reduced, and this will reduce the overall running cost.
CAUTION
►►Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from fragments of glass, or the TV may fall.
►►Do not drag the TV. The floor or the product may be damaged.
■■ Image shown may differ from your TV.
PROGRAMME
VOLUME
OK
MENU
INPUT
POWER
SPEAKER
Power/Standby Indicator
(Can be adjusted using the Power
Indicator in the OPTION menu.)
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to
the surrounding conditions.
A-2
USB IN
BACK PANEL INFORMATION
■■ Image shown may differ from your TV.
32/37/42LD6***
AC IN
USB IN
H/P
AC IN
ANTENNA IN
USB IN
1
12
H/P
CABLE MANAGEMENT
PREPARATION
CABLE MANAGEMENT
2
3
5
4
6
13
AC IN
HDMI/DVI IN
CABLE MANAGEMENT
LAN
(RGB)
H/P
2
1
HDMI/DVI IN
LAN
14
(RGB)
2
VOLUME CONTROL
1
STEREO (8
)
VOLUME CONTROL
SPEAKER
OUT
STEREO (8
)
SPEAKER
OUT
7
1
2
8
9
10
11
PowerHDMI/DVI
CordINSocket
(RGB)
LAN
This TV operates on an AC power. The volt2
age is indicated on the Specifications page.
(► p.125
to 128) Never attempt to operate
1
the TV on DC power.
4
RGB IN Input
Connect the output from a PC.
9
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
10
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
11
SPEAKER OUTPUT(STEREO)
The phone socket for external speaker is on
this jack.
12
USB Input
Connect USB storage device to this jack.
13
PCMCIA (Personal Computer Memory
Card International Association) Card Slot
Insert the CI Module to PCMCIA CARD
SLOT.
(This feature is not available in all countries.)
14
Headphone Socket
Plug the headphone into the headphone
socket.
VOLUME CONTROL
Antenna Input
Connect antenna or cable to this jack.
STEREO (8
3
8
)
SPEAKER
OUT
LAN
Network connection.
Also used for video, photo and music files on
a local network.
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of
equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
5
Component Input
Connect a component video/audio device to
these jacks.
6
Euro Scart Socket (AV1)
Connect scart socket input or output from an
external device to these jacks.
7
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI
(VIDEO) signal to HDMI/DVI port with DVI to
HDMI cable.
A-3
USB IN
PREPARATION
47LD6***
AC IN
CABLE MANAGEMENT
H/P
USB IN
PREPARATION
AC IN
USB IN
1
13
H/P
CABLE MANAGEMENT
2
5
4
3
6
14
AC IN
AUX LAN
HDMI/DVI IN
CABLE MANAGEMENT
(RGB)
LAN
H/P
2
1
HDMI/DVI IN
LAN
15
(RGB)
2
VOLUME CONTROL
ANTENNA
IN
1
STEREO (8
)
VOLUME CONTROL
SPEAKER
OUT
STEREO (8
)
SPEAKER
OUT
7
1
2
8
9
10
11
PowerHDMI/DVI
CordINSocket
(RGB)
LAN
This TV operates on an AC power. The volt2
age is indicated on the Specifications page.
(► p.125
to 128) Never attempt to operate
1
the TV on DC power.
3
AUX LAN
Network connection.
4
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of
equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
6
7
A-4
8
RGB IN Input
Connect the output from a PC.
9
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
10
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
11
SPEAKER OUTPUT(STEREO)
The phone socket for external speaker is on
this jack.
12
Antenna Input
Connect antenna or cable to this jack.
13
USB Input
Connect USB storage device to this jack.
14
PCMCIA (Personal Computer Memory
Card International Association) Card Slot
Insert the CI Module to PCMCIA CARD
SLOT.
(This feature is not available in all countries.)
15
Headphone Socket
Plug the headphone into the headphone
socket.
VOLUME CONTROL
LAN
Network connection.
SPEAKER
Also used for video, photo and music files
on
OUT
a local network.
STEREO (8
5
12
)
Component Input
Connect a component video/audio device to
these jacks.
Euro Scart Socket (AV1)
Connect scart socket input or output from an
external device to these jacks.
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI
(VIDEO) signal to HDMI/DVI port with DVI to
HDMI cable.
STAND INSTALLATION
1
Carefully place the TV screen side down
on a cushioned surface to protect the
screen from damage.
2
Assemble the parts of the Stand Body with
the Stand Base of the TV.
4
Fix the 4 bolts securely using the holes in
the back of the TV.
x4
PREPARATION
■■ Image shown may differ from your TV.
When assembling the desk type stand, check whether the bolt is fully tightened.
(If not tightened fully, the product can tilt forward after the product installation.)
If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening
part of the bolt.
Tighten the stand with the
four screws (provided as
parts of the TV).
Stand Body
M4 X 20
Stand Base
3
Assemble the TV as shown.
A-5
AC IN
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
■■ Image shown may differ from your TV.
PREPARATION
32/37/42LD6***
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the Protective
Bracket/Bolt or the Plug in type Holder. It
will help prevent the power cable from being
removed by accident.
3
Put the cables inside the Cable
Management Clip and snap it closed.
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
47LD6***
1
Protective Bracket/Bolt
(This feature is not available
for all models.)
AC IN
or
AC IN
AC IN
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the Protective
Bracket/Bolt. It will help prevent the power
cable from being removed by accident.
AC IN
AC IN
AC IN
AC IN
AC IN
Plug in type Holder
2
Install the Cable Management Clip as shown.
If your TV has the Cable Holder, install it as
shown and bundle the cables.
Protective Bracket/Bolt
(This feature is not available
for all models.)
AC IN
AC IN
2
Put the cables inside the Cable
Management Clip and snap it closed.
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
Cable Management Clip
Cable Holder
NOTE
AC IN
AC IN
AC IN
►Do
► not hold the Cable Management Clip when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken.
►With
►
some TVs, the Plug in type Holder and the Cable Holder are included. If these holders
are inserted into the hole provided on back of the TV, they cannot be removed.
AC IN
A-6
AC IN
SWIVEL STAND
■ Image shown may differ from your TV.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially
causing injury or damaging the product.
PREPARATION
■ Image shown may differ from your TV.
After installing the TV, you can adjust the TV set
manually to the left or right direction by 20
degrees to suit your viewing position.
ATTACHING THE TV TO A
DESK (Only 32/37/42/47LD6***)
4-Screws
(not provided as parts of the product)
Stand
NOT USING THE
DESK-TYPE STAND
■ Image shown may differ from your TV.
When installing the wall-mounted unit, use the
protection cover.
Insert the Protection Cover into the TV until
clicking sound.
Desk
►Screws: M5 x L (*L: Table depth + 8-10 mm)
ex) Table depth: 15mm, Screw: M5 x 25
(Only 32/37/42LD6***)
Protection Cover
1-Screw (provided as parts of the product)
Stand
Desk
WARNING
►To prevent TV from falling over, the TV
should be securely attached to the floor/wall
per installation instructions. Tipping, shaking,
or rocking the machine may cause injury.
A-7
PREPARATION
KENSINGTON SECURITY
SYSTEM
PREPARATION
■■ This feature is not available for all models.
■■ Image shown may differ from your TV.
he TV is equipped with a Kensington Security
T
System connector on the back panel. Connect
the Kensington Security System cable as shown
below.
For the detailed installation and use of the
Kensington Security System, refer to the user’s
guide provided with the Kensington Security
System.
For further information, contact http://www.kensington.com, the internet homepage of the
Kensington
company. Kensington sells security systems for
expensive electronic equipment such as notebook PCs and LCD projectors.
NOTE
►►The Kensington Security System is an optional
accessory.
►►If the TV feels cold to the touch, there may be a
small “flicker” when it is turned on.
This is normal, there is nothing wrong with TV.
►►Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.
►►Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary distortion
effects on the screen.
CAREFUL INSTALLATION
ADVICE
■■ You should purchase necessary components
to fix the TV safety and secure to the wall on
the market.
■■ Position the TV close to the wall to avoid the
possibility of it falling when pushed.
■■ The instructions shown below are a safer way
to set up the TV, by fixing it to the wall, avoiding the possibility of it falling forwards if pulled.
This will prevent the TV from falling forward
and causing injury. This will also prevent the
TV from damage. Ensure that children do not
climb or hang from the TV.
1
1
2
2
1
2
Use the eye-bolts or TV brackets/bolts to fix the
product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then
bolts.)
* Insert the eye-bolts or TV brackets/bolts and
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the
wall. Match the height of the bracket that is
mounted on the wall.
3
3
Use a sturdy rope to tie the product for alignment. It is safer to tie the rope so it becomes
horizontal between the wall and the product.
NOTE
►►When moving the TV undo the cords first.
►►Use a platform or cabinet strong and large
enough to support the size and weight of the TV.
►►To use the TV safely make sure that the height of
the bracket on the wall and on the TV is the
same.
A-8
■■ The TV can be installed in various ways such as
on a wall, or on a desktop etc.
■■ The TV is designed to be mounted horizontally.
Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are
not possible, have a qualified electrician install a
separate circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
Power
Supply
Circuit
breaker
DESKTOP PEDESTAL
INSTALLATION
►Should
►
Install wall mount on a solid wall
perpendicular to the floor.
►Should
►
use a special wall mount, if you
want to install it to ceiling or slanted wall.
►The
►
surface that wall mount is to be
mounted on should be of sufficient
strength to support the weight of TV set;
e.g. concrete, natural rock, brick and hollow block.
►Installing
►
screw type and length depends
on the wall mount used. Further information, refer to the instructions included with
the mount.
►LG
► is not liable for any accidents or damage to property or TV due to incorrect
installation:
- Where a non-compliant VESA wall
mount is used.
- Incorrect fastening of screws to surface
which may cause TV to fall and cause
personal injury.
- Not following the recommended
Installation method.
10 cm
■■ Image shown may differ from your TV.
For adequate ventilation allow a clearance of 10
cm all around the TV.
10 cm
10 cm
10 cm
10 cm
10 cm
PREPARATION
EARTHING
NOTE
10 cm
10 cm
WALL MOUNT: HORIZONTAL
INSTALLATION
■■ We recommend the use of a LG Brand wall
mounting bracket when mounting the TV to a wall.
■■ We recommend that you purchase a wall mounting bracket which supports VESA standard.
■■ LG recommends that wall mounting be performed by a qualified professional installer.
VESA
Standard Quantity
Screw
(A * B)
32LD6***
200 * 100
M4
4
37/42/47LD6*** 200 * 200
M6
4
Model
A-9
PREPARATION
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
PREPARATION
(POWER) Switches the TV on from standby or off to standby.
ENERGY
AV MODE
ENERGY Adjust the Energy Saving mode of the TV.(► p.82)
SAVING
INPUT
TV/
RAD
SAVING
AV MODE It helps you select and set images and sounds
when connecting AV devices.(► p.38)
1.,;@ 2 abc 3 def
INPUT External input mode rotate in regular sequence.
(► p.31)
4 ghi 5 jkl 6 mno
7pqrs 8 tuv 9 wxyz
0
[
LIST
TV/RAD Selects Radio, TV and DTV programme.
Q.VIEW
GUIDE Shows programme guide. (► p.75)
CHAR/NUM
PORTAL Displays and removes the hotel interactive menu.
MARK
RATIO
P
DELETE
INFO i Shows the present screen information.
THUMBSTICK Allows you to navigate the on-screen menus and
(Up/Down/Left/Right) adjust the system settings to your preference.
MUTE
GUIDE PORTAL INFO
OK Accepts your selection or displays the current
mode.
MENU Selects a menu.
Clears all on-screen displays and returns to TV
viewing from any menu.(► p.19)
OK
MENU
P
A
G
E
BACK EXIT
BACK Allows the user to move return one step in an interactive application, EPG or other user interaction
function.
EXIT Clears all on-screen displays and returns to TV
viewing from any menu.
Q. MENU Select the desired quick menu source. (Aspect
Ratio, Clear Voice II , Picture Mode, Sound Mode,
Audio (or Audio Language), Sleep Timer, Skip Off/
On, USB Device).(► p.18)
AD Switches the Audio Description On or Off.
Q.MENU
A-10
AD
ALARM
ALARM Sets the alarm function.
AV MODE
0 to 9 number Selects a programme.
button Selects numbered items in a menu.
INPUT
TV/
RAD
1.,;@ 2 abc 3 def
]
SAVING
(Space) Opens an empty space on the screen keyboard.
PREPARATION
ENERGY
LIST Displays the programme table. (► p.30)
4 ghi 5 jkl 6 mno
Q.VIEW Returns to the previously viewed programme.
7pqrs 8 tuv 9 wxyz
0
[
LIST
Q.VIEW
CHAR/NUM
MARK
RATIO
P
Coloured These buttons are used for teletext (on TELETEXT
buttons models only), Programme edit.
P
A
G
E
DELETE
MUTE
GUIDE PORTAL INFO
OK
MENU
BACK EXIT
1
1
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section.
(► p.118)
SUBTITLE Recalls your preferred subtitle in digital mode.
Q.MENU
AD
ALARM
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu
appears at the screen.(► p.34)
A-11
PREPARATION
PREPARATION
VOLUME UP Adjusts the volume. /DOWN
ENERGY
AV MODE
CHAR/NUM Shifts the Character or Number.
INPUT
TV/
RAD
MARK Select the input to apply the Picture Wizard
settings.
Check and un-check programmes in the USB
menu.
SAVING
1.,;@ 2 abc 3 def
RATIO Selects your desired Aspect Ratio of picture.
(► p.79)
4 ghi 5 jkl 6 mno
7pqrs 8 tuv 9 wxyz
0
[
LIST
DELETE Deletes the entered character when entering the
character on the screen keyboard.
Q.VIEW
MUTE Switches the sound on or off.
CHAR/NUM
MARK
RATIO
P
DELETE
MUTE
P
A
G
E
Programme Selects a programme.
UP/DOWN
PAGE UP/ Move from one full set of screen information to the
DOWN next one.
GUIDE PORTAL INFO
SIMPLINK / Controls SIMPLINK or MY MEDIA menu (Photo List,
MY MEDIA Music List and Movie List).
Menu
control buttons
OK
MENU
Q.MENU
A-12
BACK EXIT
AD
ALARM
Installing Batteries
■■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■■ Install two 1.5 V AAA batteries. Do not mix old or used batteries with new ones.
■■ Close cover.
■■ To remove the batteries, perform the installation actions in
reverse.
LED LCD TV MODELS : 32/37/42/47LV3***
Ensure that the following accessories are included with your TV. If an accessory is missing, please
contact the dealer where you purchased the TV.
■■ Image shown may differ from your TV.
EN
ER
GY
AV
SAVI
NG
4g
hi
7pq
rs
LIS
T
ID
E
MU
RT
AL
OK
DE
TE
RA
TIO
LE
TE
PO
AR
8 tu
UM
DE
INPU
2 ab
c
l
9 wxy
6m
3d
TV
RA /
D
ef
no
z
Q.V
/N
RK
MO
T
5 jk
v
[
0
CH
MA
GU
1.,;@
PREPARATION
ACCESSORIES
IEW
P
E
A
G
P
IN
FO
ME
NU
BA
CK
EX
IT
Q.M
EN
U
AD
ALA
RM
Owner’s Manual
Batteries
(AAA)
Only 32/37LV3***
This item is not included for all models.
*L
ightly wipe any stains
or fingerprints on the
surface of the TV with
the polishing cloth.
x8
(M4x12)
Bolts for stand assembly
Remote Control
1-screw for stand fixing
Polishing Cloth
Do not use excessive
Polishing cloth for force. This may cause
use on the screen. scratching or discolouration.
Ferrite Core
(This item is not included
for all models.)
Use of ferrite core (This feature is not available for all models.)
Ferrite core can be used to reduce the electromagnetic
wave when connecting the power cord.
The closer the location of the ferrite core to the power
plug, the better it is.
Install the power plug closely.
A-13
PREPARATION
FRONT PANEL CONTROLS
NOTE
PREPARATION
►TV
► can be placed in standby mode in order to reduce the power consumption. And TV should be
switched off using the power switch on the TV if it will not be watched for some time, as this will
reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of
brightness of the picture is reduced, and this will reduce the overall running cost.
CAUTION
►►Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from fragments of glass, or the TV may fall.
►►Do not drag the TV. The floor or the product may be damaged.
■■ Image shown may differ from your TV.
Power/Standby Indicator
(Can be adjusted using the Power
Indicator in the OPTION menu.)
Intelligent Sensor
Adjusts picture according to
the surrounding conditions.
Remote Control Sensor
SPEAKER
Touch buttons1
HOME
HOME
VOLUME
PROGRAMME
OK
POWER
INPUT
Touch button
Description
Scrolls through the saved programmes
Adjusts the volume level
Selects the highlighted menu option or confirms an input
HOME
Accesses the main menus, or saves your input and exits the menus
Changes the input source
Turns the power on or off
A-14
1.Touch Button - You can use the desired button function by touching.
USB IN
BACK PANEL INFORMATION
H/P
2
5
4
3
13
H/P
USB IN
1
PREPARATION
USB IN
■■ Image shown may differ from your TV.
6
14
AUX LAN
HDMI/DVI IN
(RGB)
LAN
2
HDMI/DVI IN
H/P
AUX LAN
1
SPEAKER
OUT
15
(RGB)
LAN
2
VOLUME CONTROL
1
SPEAKER
ANTENNA
OUT
IN
STEREO (8
)
VOLUME CONTROL
ANTENNA
IN
STEREO (8
7
8
9
10
11
)
12
AUX LAN
1
Power Cord Socket
HDMI/DVI IN
(RGB)
LAN on an AC power. The voltThis TV
operates
age is 2indicated on the Specifications page.
(► p.125 to 128) Never attempt to operate
the TV1 on DC power.
SPEAKER
8
RGB IN Input
Connect the output from a PC.
9
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
10
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
11
SPEAKER OUTPUT(STEREO)
The phone socket for external speaker is on
this jack.
12
Antenna Input
Connect antenna or cable to this jack.
13
USB Input
Connect USB storage device to this jack.
14
PCMCIA (Personal Computer Memory
Card International Association) Card Slot
Insert the CI Module to PCMCIA CARD
SLOT.
(This feature is not available in all countries.)
15
Headphone Socket
Plug the headphone into the headphone
socket.
OUT
2
LAN
Network connection.
ANTENNA
IN
Also used for video, photo and music files on
a local network.
VOLUME CONTROL
STEREO (8
3
AUX LAN
Network connection.
4
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of
equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
5
6
7
)
Component Input
Connect a component video/audio device to
these jacks.
Euro Scart Socket (AV1)
Connect scart socket input or output from an
external device to these jacks.
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI
(VIDEO) signal to HDMI/DVI port with DVI to
HDMI cable.
A-15
PREPARATION
STAND INSTALLATION
PREPARATION
■■ Image shown may differ from your TV.
When assembling the desk type stand, check
whether the bolt is fully tightened.
(If not tightened fully, the product can tilt forward
after the product installation.)
If you tighten the bolt with excessive force, the
bolt can deviate from abrasion of the tightening
part of the bolt.
1
2
BACK COVER FOR WIRE
ARRANGEMENT
■■ Image shown may differ from your TV.
1
Gather and bind the cables with the Cable
Holder on the TV back cover.
Carefully place the TV screen side down
on a cushioned surface to protect the
screen from damage.
Assemble the parts of the Stand Body
with the Stand Base of the TV.
Stand Body
Cable Holder
SWIVEL STAND
M4 X 12
Stand Base
3
4
A-16
Assemble the TV as shown.
Secure the TV and the stand with the 4
screws.
■■ Image shown may differ from your TV.
After installing the TV, you can adjust the TV set
manually to the left or right direction by 20
degrees to suit your viewing position.
KENSINGTON SECURITY
SYSTEM
■ Image shown may differ from your TV.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially
causing injury or damaging the product.
■ This feature is not available for all models.
■ Image shown may differ from your TV.
4-Screws
(not provided as parts of the product)
Stand
The TV is equipped with a Kensington
Security System connector on the back panel.
Connect the Kensington Security System
cable as shown below.
For the detailed installation and use of the
Kensington Security System, refer to the
user’s guide provided with the Kensington
Security System.
For further information, contact http://www.
kensington.com, the internet homepage of
the Kensington
company. Kensington sells security systems
for expensive electronic equipment such as
notebook PCs and LCD projectors.
PREPARATION
ATTACHING THE TV TO A
DESK (Only 32/37/42/47LV3***)
NOTE
Desk
►Screws: M5 x L (*L: Table depth + 8-10 mm)
ex) Table depth: 15mm, Screw: M5 x 25
(Only 32/37LV3***)
1-Screw (provided as parts of the product)
► The Kensington Security System is an optional accessory.
► If the TV feels cold to the touch, there may
be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with
TV.
► Some minute dot defects may be visible on
the screen, appearing as tiny red, green, or
blue spots. However, they have no adverse
effect on the monitor's performance.
► Avoid touching the LCD screen or holding
your finger(s) against it for long periods of
time.
Doing so may produce some temporary distortion effects on the screen.
Stand
Desk
WARNING
►To prevent TV from falling over, the TV
should be securely attached to the floor/
wall per installation instructions. Tipping,
shaking, or rocking the machine may cause
injury.
A-17
PREPARATION
CAREFUL INSTALLATION
ADVICE
PREPARATION
■■ You should purchase necessary components
to fix the TV safety and secure to the wall on
the market.
■■ Position the TV close to the wall to avoid the
possibility of it falling when pushed.
■■ The instructions shown below are a safer way
to set up the TV, by fixing it to the wall, avoiding the possibility of it falling forwards if
pulled. This will prevent the TV from falling
forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are
not possible, have a qualified electrician install a
separate circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
Power
Supply
2
2
2
EARTHING
1
1
1
■■ The TV can be installed in various ways such as
on a wall, or on a desktop etc.
■■ The TV is designed to be mounted horizontally.
Use the eye-bolts or TV brackets/bolts to fix the
product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then
bolts.)
* Insert the eye-bolts or TV brackets/bolts and
tighten them securely in the upper holes.
Circuit
breaker
DESKTOP PEDESTAL
INSTALLATION
■■ Image shown may differ from your TV.
For adequate ventilation allow a clearance of 10
cm all around the TV.
Secure the wall brackets with the bolts on the
wall. Match the height of the bracket that is
mounted on the wall.
10 cm
10 cm
3
3
Use a sturdy rope to tie the product for alignment. It is safer to tie the rope so it becomes
horizontal between the wall and the product.
NOTE
►►When moving the TV undo the cords first.
►►Use a platform or cabinet strong and large
enough to support the size and weight of the TV.
►►To use the TV safely make sure that the height of
the bracket on the wall and on the TV is the
same.
A-18
10 cm
10 cm
WALL MOUNT: HORIZONTAL INSTALLATION
NOTE
►Should
►
Install wall mount on a solid wall perpendicular to the floor.
►Should
►
use a special wall mount, if you want
to install it to ceiling or slanted wall.
►The
►
surface that wall mount is to be mounted on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block.
►Installing
►
screw type and length depends on
the wall mount used. Further information,
refer to the instructions included with the
mount.
►LG
► is not liable for any accidents or damage
to property or TV due to incorrect installation:
- Where a non-compliant VESA wall mount
is used.
- Incorrect fastening of screws to surface
which may cause TV to fall and cause personal injury.
- Not following the recommended Installation
method.
VESA
Standard
Quantity
Screw
(A * B)
32LV3***
200 * 100
M4
4
37LV3***
200 * 200
M6
4
42/47LV3*** 400 * 400
M6
4
PREPARATION
■■ We recommend the use of a LG Brand wall
mounting bracket when mounting the TV to a wall.
■■ We recommend that you purchase a wall mounting bracket which supports VESA standard.
■■ LG recommends that wall mounting be performed by a qualified professional installer.
Model
10 cm
10 cm
10 cm
10 cm
A-19
PREPARATION
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
PREPARATION
(POWER) Switches the TV on from standby or off to standby.
ENERGY
AV MODE
ENERGY Adjust the Energy Saving mode of the TV.(► p.82)
SAVING
INPUT
TV/
RAD
SAVING
AV MODE It helps you select and set images and sounds
when connecting AV devices.(► p.38)
1.,;@ 2 abc 3 def
INPUT External input mode rotate in regular sequence.
(► p.31)
4 ghi 5 jkl 6 mno
7pqrs 8 tuv 9 wxyz
0
[
LIST
TV/RAD Selects Radio, TV and DTV programme.
Q.VIEW
GUIDE Shows programme guide. (► p.75)
CHAR/NUM
PORTAL Displays and removes the hotel interactive menu.
MARK
RATIO
P
DELETE
INFO i Shows the present screen information.
THUMBSTICK Allows you to navigate the on-screen menus and
(Up/Down/Left/Right) adjust the system settings to your preference.
MUTE
GUIDE PORTAL INFO
OK Accepts your selection or displays the current
mode.
Home Selects a menu.
Clears all on-screen displays and returns to TV
viewing from any menu.(► p.19)
OK
Home
P
A
G
E
BACK EXIT
BACK Allows the user to move return one step in an interactive application, EPG or other user interaction
function.
EXIT Clears all on-screen displays and returns to TV
viewing from any menu.
Q. MENU Select the desired quick menu source. (Aspect
Ratio, Clear Voice II , Picture Mode, Sound Mode,
Audio (or Audio Language), Sleep Timer, Skip Off/
On, USB Device).(► p.18)
AD Switches the Audio Description On or Off.
Q.MENU
A-20
AD
ALARM
ALARM Sets the alarm function.
AV MODE
0 to 9 number Selects a programme.
button Selects numbered items in a menu.
INPUT
TV/
RAD
1.,;@ 2 abc 3 def
]
SAVING
(Space) Opens an empty space on the screen keyboard.
PREPARATION
ENERGY
LIST Displays the programme table. (► p.30)
4 ghi 5 jkl 6 mno
Q.VIEW Returns to the previously viewed programme.
7pqrs 8 tuv 9 wxyz
0
[
LIST
Q.VIEW
CHAR/NUM
MARK
RATIO
P
Coloured These buttons are used for teletext (on TELETEXT
buttons models only), Programme edit.
P
A
G
E
DELETE
MUTE
GUIDE PORTAL INFO
OK
Home
BACK EXIT
1
1
TELETEXT These buttons are used for teletext.
BUTTONS For further details, see the ‘Teletext’ section.
(► p.118)
SUBTITLE Recalls your preferred subtitle in digital mode.
Q.MENU
AD
ALARM
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu
appears at the screen.(► p.34)
A-21
PREPARATION
PREPARATION
VOLUME UP Adjusts the volume. /DOWN
ENERGY
AV MODE
CHAR/NUM Shifts the Character or Number.
INPUT
TV/
RAD
MARK Select the input to apply the Picture Wizard
settings.
Check and un-check programmes in the USB
menu.
SAVING
1.,;@ 2 abc 3 def
RATIO Selects your desired Aspect Ratio of picture.
(► p.79)
4 ghi 5 jkl 6 mno
7pqrs 8 tuv 9 wxyz
0
[
LIST
DELETE Deletes the entered character when entering the
character on the screen keyboard.
Q.VIEW
MUTE Switches the sound on or off.
CHAR/NUM
MARK
RATIO
P
DELETE
MUTE
P
A
G
E
Programme Selects a programme.
UP/DOWN
PAGE UP/ Move from one full set of screen information to the
DOWN next one.
GUIDE PORTAL INFO
SIMPLINK / Controls SIMPLINK or MY MEDIA menu (Photo List,
MY MEDIA Music List and Movie List).
Menu
control buttons
OK
Home
Q.MENU
A-22
BACK EXIT
AD
ALARM
Installing Batteries
■■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■■ Install two 1.5 V AAA batteries. Do not mix old or used batteries with new ones.
■■ Close cover.
■■ To remove the batteries, perform the installation actions in
reverse.
EXTERNAL EQUIPMENT SETUP
■ To prevent damage do not connect to the mains outlet until all connections are made between the
devices.
■ This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 32/37/42LD6***
models.
■ Image shown may differ from your TV.
■ For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA IN
EXTERNAL EQUIPMENT SETUP
ANTENNA CONNECTION
RF Coaxial Wire (75 Ω)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
UHF
Antenna
Signal
Amplifier
ANTENNA IN
VHF
■ In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier
to the antenna as shown above.
■ If signal needs to be split for two TVs, use an antenna signal splitter for connection.
1
EXTERNAL EQUIPMENT SETUP
■■ To avoid damaging any equipment, never plug in any power cord until you have finished connecting
all equipment.
CONNECTING WITH A COMPONENT CABLE
EXTERNAL EQUIPMENT SETUP
This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do
receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as
shown below.
1
2
Connect the video outputs (Y, PB, PR) of the
external equipment (digital set-top box, DVD,
etc.) to the COMPONENT IN VIDEO jacks on
the TV.
HDMI/DVI IN
2
1
RJP
INTERFAC
LAN
(RGB)
1
Connect the audio output of the external equipment (digital set-top box, DVD, etc.) to the
COMPONENT IN AUDIO jacks on the TV.
3
Turn on the external equipment.
(Refer to the external equipment's manual for
operating instructions.)
4
Select the Component input source using the
INPUT button on the remote control.
VOLUME CONTR
STEREO (8
2
►►HDMI Audio Supported format : Dolby Digital, PCM.
DTS Audio format is not supported.
Signal
Component
HDMI
480i/576i
480p/576p
720p/1080i
O
O
O
X
O
O
O
1080p
O
(50 Hz / 60 Hz only)
(24 Hz / 30 Hz /
50 Hz / 60 Hz)
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
2
Component ports on the TV
Y
PB
PR
Video output ports
on DVD player
Y
Y
Y
Y
PB
B-Y
Cb
Pb
PR
R-Y
Cr
Pr
SPEAKER
OUT
CONNECTING WITH AN HDMI CABLE
1
Connect the HDMI output of the external equipment (digital settop box, DVD, etc.) to HDMI/DVI IN 1, HDMI/DVI IN 2 jack on
the TV.
Turn on the external equipment.
(Refer to the external equipment's manual for operating
instructions.)
3
Select HDMI1, HDMI2 input source using the INPUT button on
the remote control.
2
1
NOTE
1
►The
►
TV can receive video and audio signals simultaneously
when using an HDMI cable.
►If
► the DVD does not support Auto HDMI, you must set the
output resolution appropriately.
►Check
►
that your HDMI cable is High Speed HDMI Cable. If
the HDMI cables are not High Speed HDMI Cable, flickering
or no screen display can result. Please use the High Speed
HDMI Cable.
HDMI/DVI IN
2
LAN
EXTERNAL EQUIPMENT SETUP
2
HDMI/DVI IN
LAN
(RGB)
1
VOLU
STE
S
3
STEREO (8
SPEAKER
OUT
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH AN HDMI TO DVI CABLE
1
EXTERNAL EQUIPMENT SETUP
4
Connect the digital set-top box or the DVI output of the PC to HDMI/DVI IN 1 or HDMI/DVI
IN 2 jack on the TV.
HDMI/DVI IN
LAN
2
(RGB)
1
2
Connect the audio output of the digital set-top
box or the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
3
Turn on the digital set-top box or the PC and
the TV.
(Refer to the digital set-top box or the PC
manual for operating instructions.)
4
Select HDMI1 or HDMI2 input source using the
INPUT button on the remote control.
VOLUME CONTROL
STEREO (8
SPEAKER
OUT
1
2
or
)
)
CONNECTING WITH A EURO SCART CABLE
HDMI/DVI IN
Connect the Euro scart socket of the external
equipment (DVD, VCR, etc.) to the AV1 Euro2
1
scart socket on the TV.
2
Turn on the external equipment.
(Refer to the external equipment's manual for
operating instructions.)
LAN
(RGB)
VOLUME CONTROL
STEREO (8
SPEAKER
OUT
Select AV1 input source using the INPUT button on the remote control.
3
)
1
Input
Output
Scart
Video
Audio
RGB
Video, Audio
AV1
O
O
O
Analogue TV, Digital TV
Output Type
AV1
AV1
(TV Out)
(When DTV scheduled recording is in
progress using recording equipment.)
Digital TV
Digital TV
O
Current
input mode
Analogue TV, AV
Analogue TV
Component/RGB
Analogue TV
(The input mode is converted to DTV.)
HDMI
X
X
EXTERNAL EQUIPMENT SETUP
1
►►TV Out : Outputs Analogue TV
or Digital TV signals.
O
NOTE
►►Any Euro scart cable used must be signal shielded.
5
EXTERNAL EQUIPMENT SETUP
USB SETUP
2
After connecting the USB IN jack, you use the
USB function. (► p.40)
1
or
USB IN
Connect the USB device to the USB IN jack
on the TV.
H/P
EXTERNAL EQUIPMENT SETUP
1
CONNECTING WITH AN RF CABLE
To avoid picture noise (interference), allow adequate distance between the VCR and TV.
1
Connect the ANT OUT socket of the VCR to
the ANTENNA IN socket on the TV.
ANTENNA IN
1
2
onnect the antenna cable to the ANT IN
C
socket of the VCR.
3
Press the PLAY button on the VCR and match
the appropriate channel between the TV and
VCR for viewing.
2
Wall Jack
Antenna
6
CONNECTING WITH A D-SUB 15 PIN CABLE
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's setHDMI/DVI IN
tings.
2
1
Connect the RGB output of the PC to the RGB
IN (PC) jack on the TV.
(RGB)
1
VOLUME CONTROL
3
Turn on the PC and the TV
4
Select RGB input source using the INPUT button on the remote control.
EXTERNAL EQUIPMENT SETUP
Connect the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
2
RJP
INTERFACE
LAN
STEREO (8
SPEAKER
OUT
WIRELESS
CONTROL
2
1
SPEAKER OUTPUT SETUP
1
Connect the external speaker to the SPEAKER
OUTPUT(STEREO) jack on the TV.
1
Method of Volume control port
Cable
Spec.
• Each Up/ Down pin is
pulled to 3.3V with CPU
GPIO.
GND / Up / Down
• CPU detects transition
from 3.3V to GND level for
volume control.
1
7
)
EXTERNAL EQUIPMENT SETUP
INSERTION OF A CI MODULE
1
AC IN
CABLE MANAGEMENT
H/P
For further information, see p.29.
H/P
NOTE
HDMI/DVI IN
LAN
(RGB)
2
1
►►Check if the CI module is inserted into the PCMCIA card slot
in the right direction. If the module is not inserted properly,
this can cause damage to the TV and the PCMCIA card slot.
HEADPHONE SETUP
VOLUME CONTROL
STEREO (8
Check this point as
shown and insert the CI
Module.
)
SPEAKER
OUT
USB IN
EXTERNAL EQUIPMENT SETUP
Insert the CI Module to PCMCIA (Personal
Computer Memory Card International
Association) CARD SLOT of TV as shown.
USB IN
USB IN
To view the encrypted (pay) services in digital TV mode.
This feature is not available in all countries.
1
Plug the headphone into the headphone socket.
2
To adjust the headphone volume, press the
+ or - button. If you press the MUTE button,
the sound from the headphone is switched off.
H/P
You can listen the sound through the headphone.
NOTE
►►AUDIO menu items are disabled when connecting a headphone.
►►When changing AV MODE with a headphone connected, the change is applied to video but not to audio.
►►Optical Digital Audio Out is not available when connecting a headphone.
►Headphone
►
impedance: 16 Ω
►Max
►
audio output of headphone: 10 mW to 15 mW
8
DIGITAL AUDIO OUT SETUP
Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL
DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
2
3
Connect one end of an optical cable to the TV
Digital Audio (Optical) Output port.
onnect the other end of the optical cable to
C
the digital audio (Optical) input on the audio
equipment.
Refer to the external audio equipment instruction manual for operation.
HDMI/DVI IN
2
RJP
INTERFACE
LAN
(RGB)
1
VOLUME CONTROL
1
STEREO (8
2
CAUTION
EXTERNAL EQUIPMENT SETUP
1
SPEAKER
OUT
►►Do not look into the optical output port. Looking at the laser
beam may damage your vision.
9
)
EXTERNAL EQUIPMENT SETUP
SUPPORTED DISPLAY RESOLUTION
RGB-PC, HDMI/DVI-PC mode
EXTERNAL EQUIPMENT SETUP
10
HDMI/DVI-DTV mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
720x400
31.468
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x768
47.78
59.87
1360x768
47.72
1280x1024
63.595
1920x1080
(RGB-PC)
1920x1080
(HDMI-PC)
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
31.469
59.94
31.5
60
31.25
50
37.5
50
44.96
59.94
59.80
45
60
60.00
33.72
59.94
33.75
60
28.125
50
26.97
23.97
66.587
59.93
67.5
60.00
Resolution
720x480
720x576
1280x720
1920x1080
27
24
33.716
29.976
33.75
30.00
56.25
50
67.43
59.94
67.5
60
NOTE
►►Connect the audio cable from the PC to the Audio
input on the TV. (Audio cables are not included with
the TV).
►►If using a sound card, adjust PC sound as required.
►►If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only
one of either RGB or HDMI IN (or HDMI/DVI IN) to
display the PC output on the TV.
►►If the graphic card on the PC does output analogue
and digital RGB simultaneously, set the TV to either
RGB or HDMI; (the other mode is set to Plug and
Play automatically by the TV.)
►►DOS mode may not work depending on the video
card if you use an HDMI to DVI cable.
►►If you use too long an RGB-PC cable, there may be
interference on the screen. We recommend using
under 5m of cable. This provides the best picture
quality.
EXTERNAL EQUIPMENT SETUP
►►Avoid keeping a fixed image on the set’s screen
for prolonged periods of time. The fixed image
may become permanently imprinted on the
screen; use a screen saver when possible.
►►There may be interference relating to resolution,
vertical pattern, contrast or brightness in PC
mode. Change the PC mode to another resolution
or change the refresh rate to another rate or
adjust the brightness and contrast on the menu
until the picture is clear. If the refresh rate of the
PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of
the PC graphic card.
►►The synchronization input waveform for Horizontal
and Vertical frequencies are separate.
►►We recommend using 1360x768, 60 Hz(Only
32LD6***), 1920x1080, 60 Hz(Only
37/42/47LD6***, 32/37/42/47LV3***) for the PC
mode, this should provide the best picture quality.
►►Connect the signal cable from the monitor output
port of the PC to the RGB (PC) port of the TV or
the signal cable from the HDMI output port of the
PC to the HDMI IN (or HDMI/DVI IN) port on the
TV.
11
EXTERNAL EQUIPMENT SETUP
SCREEN SETUP FOR PC MODE
Screen Reset
Returns Position, Size and Phase to the factory default settings.
EXTERNAL EQUIPMENT SETUP
This function works in the following mode : RGB[PC].
■ Image shown may differ from your TV.
PICTURE
Move
• Brightness
50
• Sharpness
70
• Colour
60
SCREEN
OK
Prev.
Resolution
Auto Config.
• Tint
0
R
G
• Colour Temp.
0
W
C
Position
Size
• Advanced Control
• Picture Reset
►
Screen
•• Screen
Move
To Set
Yes
No
Phase
Reset
1
MENU
2
3
4
5
or
Home
Select PICTURE.
Select Screen.
Select Reset.
Select Yes.
Run Reset.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
12
Auto Configure (RGB [PC] mode only)
Automatically adjusts the picture position and minimizes image instability. After adjustment, if the
image is still not correct, your TV is functioning properly but needs further adjustment.
■ Image shown may differ from your TV.
PICTURE
Move
• Brightness
50
• Sharpness
70
• Colour
60
SCREEN
OK
Prev.
Move
Resolution
Auto Config.
• Tint
0
R
G
• Colour Temp.
0
W
C
Position
Size
• Advanced Control
• Picture Reset
►
• Screen
Auto Config.
Yes
No
EXTERNAL EQUIPMENT SETUP
Auto configure
This function is for automatic adjustment of the screen position, size, and phase The displayed image
will be unstable for a few seconds while the auto configuration is in progress.
Phase
Reset
1
MENU
2
3
4
5
or
Home
Select PICTURE.
Select Screen.
• If the position of the image is still not correct,
try Auto adjustment again.
• If picture needs to be adjusted again after
Auto adjustment in RGB (PC), you can adjust
the Position, Size or Phase.
Select Auto Config..
Select Yes.
Run Auto Config..
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
13
EXTERNAL EQUIPMENT SETUP
Selecting Resolution
To view a normal picture, match the resolution of RGB mode and selection of PC mode.
EXTERNAL EQUIPMENT SETUP
This function works in the following mode: RGB[PC]
■ Image shown may differ from your TV.
PICTURE
Move
• Brightness
50
• Sharpness
70
• Colour
60
SCREEN
OK
Resolution
Auto Config.
• Tint
0
R
G
• Colour Temp.
0
W
C
Position
Move
Prev.
1024 x 768
1280 x 768
1360 x 768
Size
• Advanced Control
• Picture Reset
►
•• Screen
Screen
Phase
Reset
1
MENU
2
3
4
or
Select PICTURE.
Home
Select Screen.
Select Resolution.
Select the desired resolution.
5
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
14
Adjustment for screen Position, Size, Phase
This function works in the following mode : RGB[PC].
■ Image shown may differ from your TV.
PICTURE
Move
• Brightness
50
• Sharpness
70
• Colour
60
OK
• Tint
0
R
G
0
W
C
2
3
4
Position
Size
Phase
►
• Picture Reset
or
Prev.
Auto Config.
• Colour Temp.
• Screen
MENU
Move
Resolution
• Advanced Control
1
SCREEN
EXTERNAL EQUIPMENT SETUP
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust
the picture position manually.
Reset
Select PICTURE.
Home
Select Screen.
Select Position, Size or Phase.
Make appropriate adjustments.
5
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
15
EXTERNAL EQUIPMENT SETUP
NETWORK SETUP
Wired Network Connection
This TV can be connected to a local area network (LAN) via the LAN port. After making the physical
connection, the TV needs to be set up for network communication.
EXTERNAL EQUIPMENT SETUP
■■ Image shown may differ from your TV.
AUX LAN
HDMI/DVI IN
2
(RGB)
LAN
2
1
1
ANTENNA
IN
SPEAKER
OUT
Broadband Modem
Broadband Service
Router
Broadband Modem
Broadband Service
1
Connect the LAN port of the Modem or Router to the LAN port on the TV.
2
Connect the LAN port of the PC to the AUX LAN port on the TV.
(Only 47LD6***, 32/37/42/47LV3***)
CAUTION
►Do
► not connect a modular phone cable to the LAN port.
►Since
►
there are various connection methods, please follow the specifications of your
telecommunication carrier or internet service provider.
16
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
When your TV is turned on, you will be able to use its features.
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
2
In standby mode to turn TV on, press the / I, INPUT or P
button on the TV or press
the POWER, INPUT, P
or NUMBER button on the remote control and the TV will
switch on.
INITIALIZING SETUP
1
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust
the Language, Mode Setting, Country or Time Zone (When Russia is selected for Country) or
Set Password(When France is selected for Country), Auto Tuning.
Note:
a.If you close without completing the initial setting, the Initial Setting menu can be displayed again.
b.Press the BACK button to change the current OSD to the previous OSD.
c.For those countries without confirmed DTV broadcasting standards, some DTV features might
not work, depending on the DTV broadcasting environment.
d. When France is selected for Country, password is not ‘0’, ‘0’, ‘0’, ‘0’ but ‘1’, ‘2’, ‘3’, ‘4’.
WATCHING TV / PROGRAMME CONTROL
1
PROGRAMME SELECTION
1
Press the P
or NUMBER buttons to select a programme number.
VOLUME ADJUSTMENT
+ or - button to adjust the volume.
1
Press the
2
If you wish to switch the sound off, press the MUTE button.
You can cancel this function by pressing the MUTE,
+ , - or AV Mode button.
17
WATCHING TV / PROGRAMME CONTROL
QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
WATCHING TV / PROGRAMME CONTROL
Aspect Ratio: Selects your desired picture format.
For Zoom Setting, select 14:9, Zoom and
Cinema Zoom in Ratio Menu. After completing Zoom Setting, the display goes back to
Q.Menu.
Clear Voice II : By differentiating the human
sound range from others, it helps users listen to human voices better.
Picture Mode : Selects your desired Picture
Mode.
Sound Mode : It is a feature to automatically set the sound combination which it deems
the best for the images being watched.
Selects your desired Sound Mode.
◄
Aspect Ratio
Audio or Audio Language : Selects the
sound output.
Sleep Timer : Sets the sleep timer.
Skip Off/On : Selects the Skip Off/On.
USB Device : Selects “Eject” in order to eject
USB device.
►
16:9
Exit
1
Q.MENU
2
3
18
Display each menu.
Select your desired Source.
• Press the Q.MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
1
or
MENU
2
Display each menu.
Home
Select a menu item.
WATCHING TV / PROGRAMME CONTROL
3
• Press the MENU or Home/EXIT button to
return to normal TV viewing.
• Press the BACK button to move to the
previous menu screen.
Move to the pop up menu.
NOTE
►It is not possible to use CI Information in Analogue mode.
SETUP
● Auto
SETUP
Move
PICTURE
OK
Tuning
● Manual
PICTURE
Tuning
● Programme
Edit
● Booster
AUDIO
● Clear
Move
Voice II
: Off
● Sound
Mode
OK
: 16:9
Energy Saving : Off
Mode
TIME
OK
: Off
● Balance
Wizard
● Picture
AUDIO
Volume
Ratio
● Picture
●ꕊ
: Off
● CI Information
● Auto
● Aspect
Move
: Standard
• Backlight
70
• Contrast
100
• Brightness
50
• Sharpness
70
Move
OK
● Clock
TIME
3
0
L
R
● Off
Time
: Off
● On
Time
: Off
: Standard
● Sleep
• Infinite Sound : Off
● Alarm
• Treble
50
• Bass
50
Timer
: Off
: Off
• Reset
19
WATCHING TV / PROGRAMME CONTROL
LOCK
● Set
● Lock
LOCK
Move
OPTION
OK
Password
● Demo
System
: Off
OPTION
● Block
Programme
● Parental
● Input
● Key
Lock
● Country
Guidance: Blocking Off
Block
● Power
WATCHING TV / PROGRAMME CONTROL
■ Image shown may differ from your TV.
AV
Antenna
Component
RGB
HDMI1
HDMI2
Exit
Input Label
MY MEDIA
MY MEDIA
Movie List
Photo List
Press OK(
Music List
Extra Contents
) to see photos from the USB.
Option
20
OK
USB Drive
USB
Indicator
● Factory
Move
: UK
● Disability Assistance
: Off
Input List
Move
: On
● Language(Language)
● Set
INPUT
Mode
Exit
ID
Reset
:1
OK
AUTO PROGRAMME TUNING
Use this to automatically find and store all available programmes.
When you start auto programming, all previously stored service information will be deleted.
The maximum number of programmes that can be stored is 500. But the number may differ slightly
depending on broadcasting signals.
SETUP
Move
● Manual
● Manual
Tuning
● Programme
● CI
Information
Antenna
Edit
● Booster
: Off
OK
Tuning
● Programme
Edit
● Booster
● CI
Move
● Auto
Tuning
● Auto
Tuning
►
● Auto
Auto Tuning
Tuning
●
SETUP
OK
Antenna
: Off
Information
Check your antenna connection.
The previous channel information
will be updated during Auto Tuning.
SECAM L Search
Start
Close
1
MENU
2
3
4
or
Home
Select SETUP.
Select Auto Tuning.
Select Start.
• Use NUMBER buttons to input a 4-digit password
in Lock System ‘On’.
• If you wish to keep on auto tuning select Start
using the
button. Then, press the OK button.
Otherwise select Close.
• When select Italy in the County menu, If the pop
up is displayed when the conflicted programme
after Auto Tuning, select a broadcaster for
Conflicting programme number to solve.
WATCHING TV / PROGRAMME CONTROL
DVB-T, DVB-C Auto Tuning is a menu for users in countries that support DVB cable.
Run Auto tuning.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
21
WATCHING TV / PROGRAMME CONTROL
MANUAL PROGRAMME TUNING
(IN DIGITAL MODE)
Manual Tuning lets you manually add a programme to your programme list.
● Auto
Move
● Auto
● Programme
►
● Manual Tuning
Edit
● Booster
● CI
SETUP
OK
Tuning
►
WATCHING TV / PROGRAMME CONTROL
SETUP
◄
● Manual Tuning
● Programme
: Off
Move
Tuning
Edit
● Booster
Information
● CI
OK
►
DTV
● Auto
UHF CH.
30
Frequency(kHz)
474000
: Off
Information
SETUP
Move
Tuning
50%
● Signal Quality
DTV
UHF CH.
30
YLE TV1
◄
● Manual Tuning
● Programme
Edit
● Booster
● Signal Strength
OK
● CI
Information
2
YLE FST
3
YLE24
50%
Add
4
▼
Store
Cancel
Close
1
MENU
2
3
4
5
6
or
Home
Select SETUP.
•U
se NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
Select Manual Tuning.
•Y
ou can select SBAND when the country is set
to "Norway, Latvia."
Select DTV.
Select the desired channel number.
Select Update or Add if signal present.
Select a channel number to assign to each channel.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
22
1 ►
: OffYLE TV2
● Auto
Move
Tuning
● Auto
►
● Programme
Edit
● Booster
Move
◄
● Programme
: On
Edit
● Booster
Information
● CI
OK
Cable
DTV
Frequency(kHz)
Tuning
● Manual Tuning
►
● Manual Tuning
● CI
SETUP
OK
Symbol rate(kS/s)
Modulation
: On
►
362000
6875
64QAM
Information
SETUP
● Auto
● Signal Quality
50%
50%
Add
Tuning
● Manual Tuning
● Programme
Edit
● Booster
● CI
● Signal Strength
Move
Information
OK
Cable
DTV
UHF CH.
30
YLE TV1
◄
YLE TV2
: On
YLE FST
3
YLE24
4
▼
Store
Cancel
Close
1
MENU
2
3
4
5
6
or
Home
Select SETUP.
Select Manual Tuning.
Select Cable DTV.
1 ►
2
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
•S
ymbol rate : Enter a user-defined
symbol rate (Symbol rate: Speed at
which a device such as modem sends
symbols to a channel).
•M
odulation : Enter a user-defined
modulation. (Modulation: Loading of
audio or video signals onto carrier).
WATCHING TV / PROGRAMME CONTROL
SETUP
Make appropriate adjustments.
Select Update or Add if signal present.
Select a channel number to assign to each channel.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
23
WATCHING TV / PROGRAMME CONTROL
(IN ANALOGUE MODE)
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.
● Auto
Move
● Auto
● Programme
Edit
● Booster
Move
Tuning
● Programme
: Off
Edit
● Booster
Information
● CI
OK
◄
● Manual Tuning
►
● Manual Tuning
● CI
SETUP
OK
Tuning
►
WATCHING TV / PROGRAMME CONTROL
SETUP
: Off
Information
● Storage
● System
BG
● System
● Band
V/UHF
0
2
3
4
5
or
Home
Select SETUP.
Select Manual Tuning.
V/UHF
● Channel
0
● Fine
◄►
● Search
◄►
● Search
◄►
● Name
C 02
C 02
Store
Store
Close
Close
6
7
Select TV or Cable TV.
or
BG
● Band
or
►
3
◄►
8
Select the desired
programme
number on.
Cable TV
● Fine
● Name
MENU
◄
3
● Channel
1
►
TV
● Storage
9
10
Select a TV system.
Select V/UHF or Cable.
or
Select the desired
channel number.
Commence searching.
Select Store.
Select a channel number to
assign to each channel.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
•Use NUMBER buttons to input a 4-digit password in Lock System ‘On’.
•L : SECAM L/L’ (France)
BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa)
I : PAL I (U.K. / Ireland / Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
•To store another channel, repeat steps 4 to 10.
24
SETUP
● Auto
Move
Tuning
● Auto
►
● Programme
Edit
● Booster
Move
Tuning
● Programme
: Off
Edit
● Booster
Information
● CI
OK
◄
● Manual Tuning
►
● Manual Tuning
● CI
SETUP
OK
: Off
Information
►
TV
◄
● Storage
3
● Storage
● System
BG
● System
● Band
V/UHF
● Channel
or
1
● Fine
● Search
V/UHF
● Channel
● Fine
◄►
● Search
C 02
BG
● Band
◄►
►
3
1
◄►
◄►
● Name
C 02
Store
Store
Close
Close
■■Assigning a station name
You can assign a station name with five characters to each programme number.
1
MENU
2
or
Home
Select SETUP.
5
Select Manual Tuning.
3
4
Select TV or Cable TV.
6
Select Name.
7
8
Select the position and make
your choice of the second
character, and so on.
You can use an the alphabet
A to Z, the number 0 to 9, +/
-, and blank.
Select Close.
Select Store.
WATCHING TV / PROGRAMME CONTROL
● Name
Cable TV
Select a channel number to
assign to each channel.
■■Fine Tuning
Normally fine tuning is only necessary if reception is poor.
1
MENU
2
3
4
or
Home
Select SETUP.
5
Select Manual Tuning.
6
Select TV or Cable TV.
7
Fine tune for the best picture
and sound.
Select Store.
Select a channel number to
assign to each channel.
Select Fine.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
25
WATCHING TV / PROGRAMME CONTROL
PROGRAMME EDIT
When a programme number is skipped, it means that you will be unable to select it using P
during TV viewing.
button
If you wish to select the skipped programme, directly enter the programme number with the NUMBER
buttons or select it in the Programme edit menu.
This function enables you to skip the stored programmes.
WATCHING TV / PROGRAMME CONTROL
Programme Edit
SETUP
Move
● Manual
Tuning
● Booster
►
Programme
Edit
●●Manual
Tuning
Programme
Edit
● CI
OK
Tuning
►
● Auto
Page 1/2
TV
: Off
Information
1 YLE TV1 (D)
2 YLE TV2 (D)
3 YLE FST (D)
4 YLE24 (D)
5 YLE Teema (D)
6 TV4 Stockholm (D)
8 CNN (D)
7 Kanal Lokal (D)
9 TV4 (D)
10 TV4 Plus (D)
11 TV400 (D)
12 TV4 Film (D)
13 TV4 Fakta (D)
14 MediaCorp HD5 (D)
15 SNY_SSU (R)
16 Demo (R)
17 TVE 1 (R)
18 TVE 2 (D)
19 24H TVE (D)
20 CLAN/50 TVE (D)
21 LA7 (R)
▼
Pr. Change
Delete
1
MENU
2
3
4
or
Home
Previous
Move
Block/Unblock
Skip
Select SETUP.
Select Programme Edit.
Enter the Programme Edit.
Select a programme to be stored or
skipped.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
26
■■Deleting a programme
1
RED
Select Yes or No.
■■Moving a programme
1
2
GREEN
Select a programme number to be moved.
GREEN Release.
Turn the programme number to
green.
■■Skipping a programme number
1
3
Select a programme number to be skipped.
2
BLUE Turn the programme number to blue.
3
BLUE Release.
• When a programme number is skipped it
means that you will be unable to select it
using the P
button during normal TV
viewing.
• If you wish to select a skipped programme,
directly enter the programme number with
the NUMBER buttons or select it in the
programme edit or EPG.
WATCHING TV / PROGRAMME CONTROL
2
Select a programme number to be deleted.
• Select Yes to delete the selected channel.
The corresponding field is left blank.
• Select No to delete the selected channel.
The selected programme is deleted, all the
following programmes are shifted up one.
■■Locking a programme number
1
Select a programme number to be locked.
2
• It can be registered as Lock
programme even when Lock
System is turned Off.
YELLOW Turn the programme number to yellow.
3
YELLOW Release.
27
WATCHING TV / PROGRAMME CONTROL
BOOSTER
If reception for a digital channel is poor select Booster to On.
When the signal is strong, select Off.
● Programme
2
Information
: Off
Of
Off
On
►
● CI
or
MENU
Edit
● Booster
Information
1
Select SETUP.
Home
Select Booster.
3
4
Off
:: Off
►
Booster
●●Booster
Tuning
● Programme
Edit
OK
Tuning
● Manual
Tuning
Move
►
● Auto
Tuning
● Manual
● CI
SETUP
OK
►
● Auto
Move
►
WATCHING TV / PROGRAMME CONTROL
SETUP
Select On or Off.
Save.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
28
CI [COMMON INTERFACE] INFORMATION
This function enables you to watch some encrypted services (pay services). If you remove the CI
Module, you cannot watch pay services.
When the module is inserted into the CI slot, you can access the module menu.
To purchase a module and smart card, contact your dealer. Do not repeatedly insert or remove a CI
module from the TV. This may cause a malfunction. When the TV is turned on after inserting a CI
Module, you may not have any sound output.
This may be incompatible with the CI module and smart card.
When using a CAM(Conditional Access Module), please make sure it meets fully the requirements of
either DVB-CI or CI plus.
A abnormal process of CAM(Conditional Access Module) may cause a bad picture.
SETUP
● Auto
Move
i
OK
Tuning
● Manual
Authorizations
Tuning
● Programme
Module information
Edit
● Booster
Viaccess Module
Consultations
: Off
►
● CI Information
Select the item
• This OSD is only for illustration and the menu
options and screen format will vary according to
the Digital pay services provider.
• It is possible for you to change CI (Common
Interface) menu screen and service by consulting your dealer.
1
or
MENU
2
Select SETUP.
Select CI Information.
3
4
Home
WATCHING TV / PROGRAMME CONTROL
CI (Common Interface) functions may not be possible depending upon the country broadcasting circumstances.
Select the desired item: Module information, smart card
information, language, or software download etc.
Save.
• Press the BACK/EXIT button to move to the previous menu screen.
29
WATCHING TV / PROGRAMME CONTROL
SELECTING THE PROGRAMME LIST
You can check which programmes are stored in the memory by displaying the programme list.
Mini Glossary
Programme List
Exit
Page 1/6
1 BBC
►
Displayed when the
Locked Programme.
2 BBC
WATCHING TV / PROGRAMME CONTROL
3 BBC
4 BBC
5 BBC
Radio
6 YEL PEILI
Radio
7 YLEQ
Radio
8 YLEN KLASSINEN
Pr.Edit
■■Displaying programme LIST
1
Display the Programme List.
•Y
ou may find some blue programmes.
These have been set up to be skipped by
auto programming or in the programme
edit mode.
•S
ome programmes with the channel number shown in the programme LIST indicate
there is no station name assigned.
BLUE
Turn the programme edit.
■■Selecting a programme in the programme list
1
2
Select a programme.
Switch to the chosen programme number.
■■Paging through a programme list
1
30
Turn the pages.
2
Return to normal TV viewing.
INPUT LIST
HDMI and AV1 (SCART) can be recognized by a detect pin and thus enabled only when an external
device approves voltage.
By using TV/RAD button, you can move from External Input to RF Input and to the last watched programme in DTV/RADIO/TV mode.
Input List
Move
OK
USB Drive
Antenna
USB
AV
Component
RGB
HDMI1
HDMI2
Input Label
1
Select the input source.
Exit
• Antenna : Select it when watching the
DTV/RADIO/TV.
• USB : Select it when using USB depends
on connector.
• AV : Select it when watching the VCR or
external equipment.
• Component : Select it when using the
DVD or the Digital set-top box depends on
connector.
• RGB :Select it when using PC depends on
connector.
• HDMI : Select it when using DVD, PC or
Digital set-top box depend on connector.
WATCHING TV / PROGRAMME CONTROL
■ Image shown may differ from your TV.
31
WATCHING TV / PROGRAMME CONTROL
INPUT LABEL
Selects a label for each input source.
WATCHING TV / PROGRAMME CONTROL
■ Image shown may differ from your TV.
Input Label
Input List
Move
OK
USB Drive
Antenna
USB
AV
Component
RGB
HDMI1
HDMI2
Input Label
Exit
AV
◄
►
Component
◄
►
RGB
◄
►
HDMI1
◄
►
HDMI2
◄
►
▼
Close
1
2
3
BLUE Select Input Label.
Select the source.
Select the label.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
32
DATA SERVICE
(This menu is enabled only in Ireland. )
This function allow users to choose between MHEG(Digital Teletext) and Teletext if both exist at the same time.
If only one of them exists, either MHEG or Teletext is enabled regardless of which option you selected.
Mode
OPTION
OK
: Off
● Demo
Move
● Language(Language)
● Country
● Country
: Ireland
or
MENU
2
● Factory
:1
Home
● Set
ID
Teletext
: MHEG
►
1
Reset
ID
MHEG
MHEG
Indicator
●●Data
Data Service
Service
►
● Set
● Power
: MHEG
►
Indicator
● Factory
: Ireland
● Disability Assistance
►
● Power
●●Data
Data Service
Service
OK
: Off
● Language(Language)
● Disability Assistance
Reset
:1
Select OPTION.
Select Data Service.
3
4
Mode
►
● Demo
Move
WATCHING TV / PROGRAMME CONTROL
OPTION
Select MHEG or Teletext.
Save.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
33
WATCHING TV / PROGRAMME CONTROL
SIMPLINK
This function operates only with devices with the SIMPLINK logo.
Please check the SIMPLINK logo.
This TV might not function properly when using it with other products with HDMI-CEC function.
This allows you to control and play other AV devices connected to the display through HDMI cable
without additional cables and settings.
WATCHING TV / PROGRAMME CONTROL
If you do not want SIMPLINK menu,select “Off”.
OK
◄
Off
Exit
►
Watch TV
DISC
VCR
VCR Recorder
HDD
Speaker
1
2
3
Display the SIMPLINK.
Select On or Off.
Save.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
34
Connecting to Home Theater with the SIMPLINK logo.
1
Connect the HDMI/DVI IN 1, HDMI/DVI IN 2
terminal on the back of the TV and the HDMI output terminal of the Home Theater using HDMI
cables.
HDMI/DVI IN
LAN
2
(RGB)
1
VOLUME CONTROL
2
STEREO (8
)
SPEAKER
OUT
1
2
Select Home Theater in the Speaker menu by
pushing the SIMPLINK button.
Home Theater
►► When you select or operate a media device with
home theater function, the speaker automatically
switches to home theater speaker (HT speaker).
WATCHING TV / PROGRAMME CONTROL
3
Connect the Digital Audio output terminal on
the back of the TV and the Digital Audio input
terminal of the Home Theater using optical
cables.
NOTE
►►Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the terminal (HDMI terminal) of the SIMPLINK
device with the HDMI cable.
►►When you switch the Input source using the INPUT button on the remote control, you can stop the operation of a device controlled by SIMPLINK.
35
WATCHING TV / PROGRAMME CONTROL
SIMPLINK Functions
WATCHING TV / PROGRAMME CONTROL
36
Disc playback
Control connected AV devices by pressing the
, OK, ►, ▀, l l, ◄◄ and ►► buttons.
Direct Play
After connecting AV devices to the TV, you can directly control the devices and play media without additional settings.
Select AV device
Enables you to select one of the AV devices connected to the TV and operate it.
Power off all devices
When you switch off the TV, all connected devices are turned off.
Switch audio-out
Offers an easy way to switch audio-out.
Sync Power on
When the equipment with Simplink function connected HDMI terminal starts to play, The TV will change automatically
to turn on mode.
* A device, which is connected to the TV through an HDMI cable but does not support SIMPLINK,
does not provide this function.
Note: To operate SIMPLINK, an High Speed HDMI Cable with *CEC function should be used.
(*CEC: Consumer Electronics Control).
SIMPLINK Menu
Press the
1
2
4
5
TV viewing : Switch to the previous TV programme regardless of the current mode.
DISC playback : Select and play connected
discs.
When multiple discs are available, the device
type of discs are conveniently displayed at
the bottom of the screen.
VCR playback : Play and control the connected VCR.
DD Recordings playback : Play and conH
trol recordings stored in HDD.
udio Out to TV: Select TV speaker for Audio
A
Out.
• DVD, Recorder: Up to two supported at a time.
• VCR: Only one supported at a time
OK
◄
On
Exit
►
1
Watch TV
Selected Device
2
DISC
3
VCR
When a device is connected (displayed in
bright colour)
4
VCR
HDD Recorder
5
Speaker
When device is not connected (displayed in
gray)
WATCHING TV / PROGRAMME CONTROL
3
button and then OK button to select the desired SIMPLINK source.
37
WATCHING TV / PROGRAMME CONTROL
AV MODE
You can select the optimal images and sounds when connecting AV devices to external input.
Off
Cinema
Sport
Game
WATCHING TV / PROGRAMME CONTROL
1
Disables the AV MODE.
Optimizes video and audio for watching movies.
Optimizes video and audio for watching sports events.
Optimizes video and audio for playing games.
Off
Cinema
Game
Sport
Press the AV MODE button repeatedly to select the desired source.
2
• If you select Cinema in AV mode, Cinema will be selected both for
Picture Mode and Sound Mode in PICTURE menu and AUDIO menu
respectively.
• If you select “Off” in AV mode, the picture and image which you initially
set will be selected.
• When playing a video game using PlayStation or Xbox, it is recommended
to use the Game mode.
• When in Game mode, functions related to picture quality will be optimized for
playing games.
38
INITIALIZING(RESET TO ORIGINAL FACTORY SETTINGS)
This function initializes all settings.
But the settings of
Day and
Night of the Picture Mode cannot be initialized.
It is useful to initialize the product or when you move to other city or country.
When the Factory Reset is completed, you must restart the Initializing setup.
When the Lock System menu is "On", the message to enter the password appears.
● Demo
Move
Mode
: On
● Country
● Disability Assistance
● Disability Assistance
● Power
● Power
4
or
ID
:1
Home
All user settings and channel settings will
Indicator
be reset. Still Continue?
● Factory Reset
● Set
Select OPTION.
: UK
►
►
Indicator
ID
OK
►
3
Move
: On
● Language(Language)
: UK
►
2
Mode
● Country
● Set
MENU
● Demo
● Language(Language)
● Factory Reset
1
OPTION
OK
:1
Yes
No
WATCHING TV / PROGRAMME CONTROL
OPTION
• In Lock System "On", if you forget your
password, press '0', '3', '2', '5' on the
remote control handset.
Select Factory Reset.
Select Yes.
Start Factory Reset.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
39
TO USE
DEVICE
TO
USEAAUSB
USB
DEVICE
WHEN CONNECTING A USB DEVICE
When you connect a USB device, this pop up menu is displayed, automatically.
“POP UP MENU” will not be displayed while the OSD including Menu, EPG is activated.
When the Pop Up menu appears, you can select Music List, Photo List, Movie List or Extra Contents in the
MY MEDIA menu.
In USB device, you can not add a new folder or delete the existing folder.
1 Connect the USB device to the USB IN
• Only photo(JPEG), music (MP3), movie(DAT,
MPG, MPEG, VOB, AVI, DIVX, MP4, MKV, TS,
TRP, TP, ASF, WMV) and flash(SWF) are supported.
USB IN
jack on the TV.
or
When removing the USB device
2
H/P
TO USE A USB DEVICE
Select the USB Device menu before removing
the USB device.
Q.MENU
2
MY MEDIA
Movie List
Photo List
Press OK(
Music List
Extra Contents
) to see photos from the USB.
Option
40
1
Select Movie List, Photo List,
Music List or Extra Contents.
Exit
Select USB Device.
Select Eject.
Precautions when using the USB device
TO USE A USB DEVICE
►►Only a USB storage device is recognizable.
►►If the USB storage device is connected through a USB hub, the device is not recognizable.
►►A USB storage device using an automatic recognition programme may not be recognized.
►►A USB storage device which uses its own driver may not be recognized.
►►The recognition speed of a USB storage device may depend on each device.
►►Please do not turn off the TV or unplug the USB device when the connected USB storage device is working.
When such device is suddenly separated or unplugged, the stored files or the USB storage device may be
damaged.
►►Please do not connect the USB storage device which was artificially maneuvered on the PC. The
device may cause the product to malfunction or fail to be played. Never forget to use only a USB storage device which has normal music files, image files or movie files.
►►Please use only a USB storage device which was formatted as a FAT32 file system, NTFS file system
provided with the Windows operating system. In case of a storage device formatted as a different utility
programme which is not supported by Windows, it may not be recognized.
►►Please connect power to a USB storage device(over 0.5 A) which requires an external power supply. If
not, the device may not be recognized.
►►Please connect a USB storage device with the cable offered by the device maker.
►►Some USB storage devices may not be supported or operated smoothly.
►►File alignment method of USB storage device is similar to Window XP and filename can recognize up to 100
English characters.
►►Be sure to back up important files since data stored in a USB memory device may be damaged. We
will not be responsible for any data loss.
►►If the USB HDD does not have an external power source, the USB device may not be detected. So be sure to
connect the external power source. - Please use a power adaptor for an external power source. We do not guarantee an USB cable for an external power source.
►►If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use
up to 4 partitions or USB memory devices.
►►If a USB memory device is connected to a USB multi-card reader, its volume data may not be detected.
►►If the USB memory device does not work properly, disconnect and reconnect it.
►►How fast a USB memory device is detected differs from device to device.
►►If the USB is connected in Standby Mode, specific hard disk will automatically be loaded when the TV is
turned on.
►►The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USB
memory.
►►Any device with more than the recommended capacity may not work properly.
►►If a USB external hard disk with a "Energy Saving" function does not work, turn the hard disk off and on
again to make it work properly.
►►USB storage devices below USB 2.0 are supported as well. But they may not work properly in the
movie list.
►►Maximum of 999 folders or files can be recognized under one folder.
►►If there are too many folders and files in one folder, it may not operate properly.
41
TO USE A USB DEVICE
MOVIE LIST
You can play movie files on a USB device.
The movie list is activated once USB is detected. It is used when playing movie files on TV.
Displays the movies in the USB folder and supports Play.
Allows playback of all movies in the folder and user desired files.
It is a movie list that displays folder information and movie file.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
TO USE A USB DEVICE
42
Movie(*.mpg/*.mpeg/*.dat/*.ts/*.trp/*.tp/*.vob/*.mp4/*.mov/*.mkv/*.dvix/*.avi/*.asf/*.wmv/*.avi(motion-jpeg)/*.mp4(motionjpeg)/*.mkv(motion-jpeg))supporting file
Video format : DivX3.11, DivX4.12, DivX5.x, DivX6, Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03, Xvid1.10 beta-1/beta-2,
Mpeg-1, Mpeg-2, Mpeg-4, H.264/AVC, VC1, JPEG, Sorenson H.263
Audio format : Dolby Digital, AAC, Mpeg, MP3, LPCM, HE-AAC, ADPCM, WMA
Bit rate : within 32 kbps to 320 kbps(MP3)
External Subtitle format : *.smi/*.srt/*.sub(MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.psb(PowerDivX)
Internal Subtitle format : only, XSUB (It is the subtitle format used in DivX6 files)
• Some user-created subtitles may not work properly.
• Some special characters are not supported in subtitles.
• HTML tags are not supported in subtitles.
• Subtitles in languages other than the supported languages are not available.
• Changing font and colour in subtitles is not supported.
• Subtitles in languages other than one specified are not supported.
• Video files with subtitle files of 1 MB or larger may not be played properly.
• The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audio language is
changed.
• A damaged movie file may not be played correctly, or some player functions may not be usable.
• Movie files produced with some encoders may not be played correctly.
• If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.
• HD videos with a maximum of 1920x1080@25/30P or 1280x720@50/60P are supported, depending on the frame.
• Videos with resolutions higher than 1920X1080@25/30P or 1280x720@50/60P may not work properly depending on
the frame.
• Movie files other than the specified types and formats may not work properly.
• Max bitrate of playable movie file is 20 Mbps.
• We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC.
• DTS Audio codec is not supported.
• A movie file more than 30 GB in file size is not supported for playback.
• A DivX movie file and its subtitle file must be located in the same folder.
• A video file name and its subtitle file name must be identical for it to be displayed.
• Playing a video via a USB connection that doesn’t support high speed may not work properly.
• The movie file encoded by the GMC (Global Motion Compensation) and Qpel (Quarterpel Motion Estimation) is not
supported.
• When you are watching the movie by Movie List function, you can adjust an image by Energy Saving and AV Mode
key on the remote control. User setup for each image mode does not operate.
• Trick Mode does not support other functions than ►► if video files do not have index information.
• When playing video file using network, the Trick mode is limited to 2-times speed.
• Video file names that contain special characters may not be playable.
Supported DivX file
File Extensions
.asf
.wmv
A/V
Video
Audio
Codec
Profile/Level Support
VC-1 Advanced Profile
Advanced Profile@Level 3
(e.g. 720p60, 1080i60, 1080p30)
Only streams compliant
to SMPTE 421M VC-1
VC-1 Simple and Main Simple Profile@Medium Level (e.g. CIF, QVGA)
standard
are supported.
Profiles
Main Profile@High Level (e.g. 1080p30)
WMA Standard
WMA 9 Professional
DivX3.11
DivX4
DivX5
DivX6
.divx
.avi
Video
Video
H.264 / AVC
Main Profile@ Level 4.1
High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30)
Advanced Simple Profile (e.g.
720p/1080i)
Audio
AAC
AAC-LC and HE-AAC
Video
H.264 / AVC
Main Profile@ Level 4.1
High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30)
Audio
AAC
Dolby Digital
H.264 / AVC
MPEG-2
Video
VC-1
Audio
Video
.vob
Audio
.mpg
Main Profile@ Level 4.1
High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30)
MPEG-1Layer I, II
MPEG-1 Layer III(MP3)
Dolby Digital
MPEG-4 Part 2
.mkv
.ts
.trp
.tp
Advanced Simple Profile
(e.g. 720p/1080i)
Video
Audio
Global motion compensation or quarterpel motion estimation does not
supported. Streams
using this syntax are
not supported.
Global motion
compensation or
quarterpel motion
estimation does
not supported.
Streams using this
syntax are not supported.
Most of the MKV
content available is
encoded by the open
source x264 codec.
TO USE A USB DEVICE
.mp4
.m4v
XViD
H.264 / AVC
Audio
Explanation
AAC-LC and HE-AAC
Main Profile@ Level 4.1
High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30)
Main Profile@High Level(e.g. 720p60, 1080i60)
Simple Profile@Medium Level
Only streams com(e.g. CIF, QVGA)
Main Profile@High Level
pliant to SMPTE
(e.g. 1080p30)
421M VC-1 standAdvanced Profile@Level3
ard are supported.
(e.g. 720p60, 1080i60, 1080p30)
MPEG-1Layer I, II
MPEG-1 Layer III(MP3)
Dolby Digital
AAC-LC and HE-AAC
AAC
MPEG-1
MPEG-2
Main Profile@High Level (e.g. 720p60, 1080i60)
Dolby Digital
MPEG-1Layer I, II
DVD-LPCM
MPEG-1
MPEG-1Layer I, II
Main Profile@High Level
(e.g. 720p60, 1080i60)
Only streams compliant
configured properly for
TS, PS or ES
43
TO USE A USB DEVICE
Screen Components
You can also adjust USB in the INPUT menu.
1
MENU
or
Home
Select MY MEDIA.
2
Select Movie List.
2
1
1
2
3
4
TO USE A USB DEVICE
5
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 1
Current page/ total pages of
contents under the folder
focused on 1
USB
Drive1
USB Drive
001
002
005
006
Page 1/1
003
5
004
4
Move
To Photo List
Change Numbers
Play
Mark Mode
P
Page Change
MARK
Mark
Exit
3
• Some files may be displayed
the preview image by icon
only.
44
Page 1/1
Movie List
• Non-supported files are
displayed the preview
image by icon only.
• Abnormal files are
displayed in the
form of bitmap.
Movie Selection
■■When playing movie files
Page 1/1
Movie List
USB
Drive1
USB Drive
001
005
Page 1/1
002
003
006
051. Apple_ ......
02:30:25
Move
To Photo List
Select the target folder or drive.
2
Play
P
Page Change
Mark Mode
• Use the P
movie page.
MARK
Mark
Exit
button to navigation in the
Select the desired movie title.
3
Movie files are played.
TO USE A USB DEVICE
1
Change Numbers
004
Using the remote control
GREEN
Repeatedly, press the GREEN button to converted to Photo List->Music List.
YELLOW
A method to view in 5 large thumbnail or simple list.
BLUE
Convert to Mark Mode.
EXIT
►
Return to normal TV viewing.
Press the PLAY(►) button to return to normal playback.
45
TO USE A USB DEVICE
■■When selected movie files are played
Page 1/1
Movie List
USB
Mark Mode
Drive1
USB Drive
Page 1/1
001
002
003
005
006
051. Apple_ ......
02:30:25
004
Move
Play Marked
TO USE A USB DEVICE
1
Page Change
Exit Mark Mode
MARK
Mark
Exit
• When one or more movie files are
marked, the marked movies will
be played in sequence.
Select the desired movie title.
CHAR/NUM
BLUE
MARK
Convert to Mark Mode.
or
4
5
Unmark All
P
Select the target folder or drive.
2
3
Mark All
Mark
Mark desired Movie file.
RED
Marked movie file is played.
NOTE
►►In the case of files not supported, a message regarding non-supported file is displayed.
46
Using the remote control
RED
Play the selected movie file.
Once a movie file finishes playing, the next selected one will be played automatically.
GREEN
Mark all movie files on the screen.
YELLOW
Deselect all marked movie files.
BLUE
Exit the Mark Mode.
Return to normal TV viewing.
TO USE A USB DEVICE
EXIT
NOTE
►If
► you select “Yes” from OSD when playing the same file after the movie file has been stopped, it
will restart where it stopped previously.
►If
► continuous series files exist within the folder, the next file will automatically be played.
But, this excludes cases when the Repeat function of Movie List Option is turned “On” (Refer to
p. 50) or when set as Marked Play.
47
TO USE A USB DEVICE
Using the Movie List function, play
Choose options.
Set Video Play.
Set Video.
Set Audio.
■
TO USE A USB DEVICE
2
II
►
1 Q.MENU
Close
◄►
►
or
01:02:30 / 02:30:25
◄◄ ►►
MENU
or
Q.MENU
Home
Option
Hide
Exit
Show the Option menu.
Select Set Video Play., Set Video. or Set Audio..
NOTE
►►Option values changed in Movie List does not affect Photo List and Music List.
►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List
excluding Movie List.
►►When replaying the video file after stopping, you can play from where it stopped previously.
48
Using the remote control
■
►
Stop the playing movie file.
Press the PLAY(►) button to return to normal playback.
During playback, press the Pause(II) button.
■■ Still screen is displayed.
■■ If no buttons are pressed on the remote control for 10 minutes after pausing,
the TV returns to the playback state.
■■ Press the Pause(II) button and then use the FF(►►) button for slow motion.
When playing,
repeatedly, press the REW(◄◄) button to speed up ◄◄(x2) -> ◄◄◄(x4) ->
◄◄◄◄(x8) ->◄◄◄◄◄(x16) ->◄◄◄◄◄◄(x32) .
repeatedly, press the FF(►►) button to speed up ►►(x2)-> ►►►(x4) ->
►►►►(x8) ->►►►►►(x16) -> ►►►►►►(x32).
II
◄◄ / ►►
MENU
or
Home
BACK
or
Q.MENU
Show the Option menu.
Hide the menu on the full-sized screen.
■■ To see the menu again on the full-sized screen, press OK button to display.
EXIT
Return to normal TV viewing.
<>
■■ When using the < or > button during playback a cursor indicating the position
can be viewed on the screen.
TO USE A USB DEVICE
■■ Pressing these buttons repeatedly increases the fast forward/reverse speed.
Press the ENERGY SAVING button repeatedly to change the brightness of
your screen.(Refer to p. 82)
Press the AV MODE button repeatedly to select the desired source.(Refer to p. 38)
49
TO USE A USB DEVICE
■■When you select the Set Video Play,
Set Video Play.
Picture Size
◄
Full
►
Audio Language
◄
1
►
Subtitle Language
◄
On
►
● Language
◄
English
►
● Code page
◄
Default
►
● Sync
◄
0
►
● Position
◄
0
►
● Size
◄
Normal
►
Repeat
◄
On
►
Previous
1
TO USE A USB DEVICE
2
Select Picture Size, Audio Language, Subtitle Langugae or Repeat.
Make appropriate adjustments.
Subtitle Language
Support Language
Latin1
English, Spanish, French, German, Italian, Swedish,
Finnish, Dutch, Portuguese, Danish, Romanian,
Norwegian, Albanian, Gaelic, Welsh, Irish,
Catalan,Valencian
Latin2
Bosnian, Polish, Croatian, Czech,
Slovak, Slovenian, Serbian, Hungarian
Latin4
Estonian, Latvian, Lithuanian
Cyrillic
Bulgarian, Macedonian, Russian, Ukrainian, Kazakh
Greek
Greek
Turkish
Turkish
►Picture
►
Size : Selects your desired picture
format during movie play.
►Audio
►
Language : Changes the Language
Group of the audio during movie play. Files
with a single audio track cannot be selected.
►►Subtitle Langugae : Turn on/off the subtitle.
►Language
►
: Activated for SMI subtitle and
can select the language within the subtitle.
►Code
►
page : Can select the font for subtitle. When set to default, same font as general menu will be used.
►Sync
►
: Adjusts the time synchronisation of
the subtitle from -10 secs to +10 secs by
steps of 0.5 secs during movie play.
►►Position : Changes the position of the subtitle
either up or down during movie play.
►Size
►
: Selects your desired Subtitle size
during movie play.
►Repeat
►
: Turn on/off repeat function of
movie playback. When turned on, the file
within the folder will be played back
repeatedly. Even when the repeated playback is turned off, it can run the playback if
the file name is similar to the previous file.
NOTE
50
►►Only 10,000 of sync blocks can be supported within the subtitle file.
►►When playing a video, you can adjust the Picture Size by pressing the RATIO button.
■■When you select the Set Video,
■■ Image shown may differ from your TV.
Set Video.
Picture Mode
◄
70
◄
● Contrast
100
◄
● Brightness
50
◄
►
● Colour
60
◄
►
►
● Dynamic Contrast
◄
Medium
►
● Edge Enhancer
◄
Low
►
● Noise Reduction
◄
Low
►
Previous
Select Picture Mode.
Make appropriate adjustments. (Refer to p. 83 to 90)
TO USE A USB DEVICE
2
►
● Backlight
Picture Reset
1
Standard
51
TO USE A USB DEVICE
■■When you select the Set Audio,
Set Audio.
Sound Mode
◄
Standard
►
Auto Volume
◄
Off
►
Clear Voice II
◄
Off
►
Balance
0
◄
L
R ►
Previous
TO USE A USB DEVICE
52
1
2
Select Sound Mode, Auto Volume, Clear Voice II or Balance.
Make appropriate adjustments. (Refer to p. 94 to 98)
PHOTO LIST
You can view photo files on USB device.
The On Screen Display may be different from your TV. Images are an example to assist with the TV operation.
When you are watching the photo by the Photo List function, you can not change the picture mode.
PHOTO(*.JPEG) supporting file
Baseline : 64 x 64 to 15360 x 8640
Progressive : 64 x 64 to 1920 x 1440
• You can play JPEG files only.
• Non-supported files are displayed in the form of predefined icon.
• An error message occurs for corrupted files or file formats that cannot be played.
• Corrupted image files may not be displayed properly.
• It may take some time to view high-resolution images in full screen.
• Files with resolution of 6145x6145 or higher are not supported. (Only 32LD6***)
TO USE A USB DEVICE
Screen Components
You can also adjust USB in the INPUT menu.
1
MENU
or
Home
2
Select MY MEDIA.
Select Photo List.
2
1
1
2
3
4
5
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 1
Current page/ total pages of
contents under the folder
focused on 1
Page 1/1
Photo List
USB
Drive1
USB Drive
001
010
002
011
Page 1/1
003
004
005
006
012
013
014
015
Move
To Music List
007
009
4
View
Mark Mode
Change Numbers
008
5
P
Page Change
MARK
Mark
Exit
3
53
TO USE A USB DEVICE
Photo Selection
■■When playing photo files
Page 1/1
Photo List
USB
Drive1
USB Drive
001
010
002
011
Page 1/1
003
004
005
006
012
013
014
015
TO USE A USB DEVICE
Move
To Music List
1
Change Numbers
Select the target folder or drive.
2
008
007
View
P
009
Page Change
MARK
Mark
Mark Mode
Exit
• Use the P
button to navigation in the
photo page.
Select the desired photos.
3
Photo files are displayed.
Using the remote control
GREEN
Repeatedly, press the GREEN button to converted to Music List->Movie List.
YELLOW
A method to view in 5 large thumbnail or simple list.
BLUE
Convert to Mark Mode.
EXIT
54
Return to normal TV viewing.
■■When selected photo files are displayed
Page 1/1
Photo List
USB
Mark Mode
Drive1
USB Drive
001
002
010
011
Page 1/1
003
004
005
006
012
013
014
015
View Marked
1
Select the desired photos.
BLUE
4
5
Unmark All
Select the target folder or drive.
2
3
Mark All
CHAR/NUM
or
MARK
Mark
P
Page Change
Exit Mark Mode
009
MARK
Mark
Exit
• When one or more photos are marked, you
can view each marked photo or a slide show
of the marked photos. If no photos are
marked, you can view every individual photo
in the folder or a slide show of all photos in
the folder.
TO USE A USB DEVICE
Move
008
007
Convert to Mark Mode.
Mark desired photo file.
RED
Marked photo file is displayed.
55
TO USE A USB DEVICE
Using the remote control
RED
GREEN
Mark all photo files on the screen.
YELLOW
Deselect all marked photo files.
BLUE
Exit the Mark Mode.
EXIT
TO USE A USB DEVICE
56
Display the selected photo file.
Return to normal TV viewing.
How to view photo
Detailed operations are available on full-sized photo view screen.
Page 1/1
Photo List
USB
Drive1
USB Drive
001
010
002
011
Page 1/1
003
004
005
006
012
013
014
015
Move
To Music List
008
007
View
P
Page Change
Mark Mode
Change Numbers
009
MARK
Mark
Exit
◄
►
The aspect ratio of a photo may change the size
of the photo displayed on the screen in full size.
Press the EXIT button to move to the previous
menu screen.
◄
Slideshow
1
2
3
►
BGM
■
2/13
TO USE A USB DEVICE
01_a.jpg
2008/12/10
1920 x 1080
479 KB
►
Q.MENU
Option
Select the target folder or drive.
Hide
Exit
• Use the P
photo page.
button to navigation in the
Select the desired photos.
The selected photo is displayed in full
size.
• Press the EXIT button to go back to Photo List.
• Press the BACK button to make Help OSD disappear.
57
TO USE A USB DEVICE
01_a.jpg
2008/12/10
1920 x 1080
479 KB
4
◄
◄
Slideshow
BGM
■
2/13
• Use
►
Q.MENU
Option
Hide
Exit
TO USE A USB DEVICE
►►Slideshow : When no picture is selected, all photos in the current folder are displayed during slide show. If some photos are
selected, those photos are displayed in a slide show.
■ Set the time interval of the slide show in Option.
►►BGM (Background Music) : Listen to music while viewing photos
in full size.
■ Set the BGM device and album in Options before using
this function.
■ You can adjust Option by Q.MENU or MENU or Home
button on the remote control.
►► � (Rotate) : Rotate photos.
■ Rotates the photo 90°, 180°, 270°, 360° clockwise.
■ It can not be rotate when the width of a picture is bigger
than supported height.
►►
/
: You can view the photo in Full or Original mode.
►►
: Press the ENERGY SAVING button repeatedly to
change the brightness of your screen. (Refer to p. 82)
►►Option : Set values for Slide Speed and BGM.
■ Use
button and OK button to set values. Press
OK to save the settings.
■ You cannot change BGM while BGM is playing.
■ You can only select the MP3 folder saved on the device
that currently displays the photo.
►►Hide : Hide the menu on the full-sized screen.
■ To see the menu again on the full-sized screen, press
OK button to display.
Press the EXIT button to go back to Photo List.
58
BGM, � (Rotate),
/ ,
,
Option, Hide or
Exit.
►
►
Select the
Slideshow,
button to select the previous
or next photo.
• Use
button to select and control
the menu on the full-sized screen.
Using the Photo List function
01_a.jpg
2008/12/10
1920 x 1080
479 KB
Choose options.
◄
►
Set Photo View.
Set Video.
Set Audio.
Close
◄
Slideshow
2
or
BGM
MENU
►
Q.MENU
■
or
Home
Option
Hide
Exit
Show the Option menu.
Select Set Photo View., Set Video. or Set Audio..
NOTE
TO USE A USB DEVICE
1 Q.MENU
►
2/13
►►Option values changed in Movie List does not affect Photo List and Music List.
►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List
excluding Movie List.
59
TO USE A USB DEVICE
■■When you select the Set Photo View,
Set Photo View.
Slide Speed
◄
BGM
Fast
...
● Repeat
◄
On
►
● Random
◄
Off
►
Previous
TO USE A USB DEVICE
60
1
2
►
Select Slide Speed or BGM.
Make appropriate adjustments.
■■When you select the Set Video,
■■ Image shown may differ from your TV.
Set Video.
Picture Mode
◄
70
◄
● Contrast
100
◄
● Brightness
50
◄
►
● Colour
60
◄
►
►
● Dynamic Contrast
◄
Medium
►
● Edge Enhancer
◄
Low
►
● Noise Reduction
◄
Low
►
Previous
Select Picture Mode.
Make appropriate adjustments. (Refer to p. 83 to 90)
TO USE A USB DEVICE
2
►
● Backlight
Picture Reset
1
Standard
61
TO USE A USB DEVICE
■■When you select the Set Audio,
Set Audio.
Sound Mode
◄
Standard
►
Auto Volume
◄
Off
►
Clear Voice II
◄
Balance
0
◄
Off
L
►
R ►
Previous
TO USE A USB DEVICE
62
1
2
Select Sound Mode, Auto Volume, Clear Voice II or Balance.
Make appropriate adjustments. (Refer to p. 94 to 98)
MUSIC LIST
You can play music files on USB device.
Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be
supported by this model.
Music file on your USB device can be played by this unit.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
MUSIC (*.MP3) supporting file
Bit rate 32 to 320
• Sampling rate MPEG1 Layer3 : 32 kHz, 44.1 kHz, 48 kHz
• Sampling rate MPEG2 Layer3 : 16 kHz, 22.05 kHz, 24 kHz
TO USE A USB DEVICE
Screen Components
You can also adjust USB in the INPUT menu.
1
MENU
or
Home
Select MY MEDIA.
2
Select Music List.
3
2
1
2
3
4
5
6
Preview: If any album jacket
for the file(Album Art Image)
exists, this jacket is displayed.
Moves to upper level folder
Current page/Total pages
Corresponding buttons on the
remote control
Contents under the folder
focused on 2
Current page/ total pages of
contents under the folder
focused on 2
Page 1/1
Music List
USB
1
USB Drive
001. - B01.mp3
00:00
Drive1
002. -B02.mp3
00:00
Page 1/1
003. B03.mp3
00:00
005. - B05.mp3
00:00
5
Move
To Movie List
6
004. - B04.mp3
00:00
Change Numbers
Play
Mark Mode
P
Page Change
MARK
Mark
Exit
4
63
TO USE A USB DEVICE
Music Selection
Page 1/1
Music List
USB
USB Drive
001. - B01.mp3
00:00
Drive1
002. -B02.mp3
00:00
Page 1/1
003. B03.mp3
00:00
004. - B04.mp3
00:00
005. - B05.mp3
00:00
Move
To Movie List
Change Numbers
■■When playing music files
TO USE A USB DEVICE
1
P
Page Change
Mark Mode
MARK
Mark
Exit
• Use the P
button to navigate up/down in
the music page.
Select the target folder or drive.
2
Select the desired music title.
3
Music files are played.
Using the remote control
GREEN
Repeatedly, press the GREEN button to converted to Movie List->Photo List.
YELLOW
A method to view in 5 large thumbnail or simple list.
BLUE
Convert to Mark Mode.
EXIT
64
Play
Return to normal TV viewing.
■■When selected music files are played
Page 1/1
Music List
Mark Mode
USB
Drive1
USB Drive
001. - B01.mp3
00:00
Page 1/1
002. -B02.mp3
00:00
003. B03.mp3
00:00
004. - B04.mp3
00:00
005. - B05.mp3
00:00
Move
Play Marked
Select the target folder or drive.
2
3
Select the desired music title.
MARK
Convert to Mark Mode.
or
4
5
CHAR/NUM
BLUE
Mark desired music file.
RED
Unmark All
Mark
P
Page Change
Exit Mark Mode
MARK
Mark
Exit
• When one or more music files are marked,
the marked music title will be played in
sequence. For example, if you want to listen
to only one music repeatedly, just mark the
music only and play it. If no music is marked,
all the music in the folder will be played in
sequence.
• If you want to activate Random playback, you
must set Option->Set audio play.->Random
to On.
TO USE A USB DEVICE
1
Mark All
Marked music file is played.
65
TO USE A USB DEVICE
Using the remote control
RED
GREEN
Mark all music files on the screen.
YELLOW
Deselect all marked music files.
BLUE
Exit the Mark Mode.
EXIT
TO USE A USB DEVICE
66
Display the selected music file.
Return to normal TV viewing.
Using the Music List function, play
Page 1/1
Music List
3 file(s) Marked
USB
Drive1
USB Drive
Page 1/1
Choose options.
Set Audio Play.
►
004. - B04.mp3
00:00
005. - B05.mp3
00:00
005. - B05.mp3
■
►
2
◄►
►
II ◄◄ ►►
or
MENU
Play with Photo
or
Home
007. - B07.mp3
00:00
008. - B08.mp3
00:00
Close
02:30 / 03:25
Q.MENU
Option
Hide
Exit
Show the Option .
Select Set Audio Play. or Set Audio.
NOTE
►►Option values changed in Movie List does not affect Photo List and Music List.
►►Option value changed in Photo List and Music List are changed likewise in Photo List and Music List
excluding Movie List.
►►You can listen to the music only within the device currently played.
TO USE A USB DEVICE
1 Q.MENU
Set Audio.
006. - B06.mp3
00:00
67
TO USE A USB DEVICE
Using the remote control
■
►
Stop the playing music file.
Press the PLAY(►) button to return to normal playback.
When you press the Pause(II) button while playing the file, the playback will be
paused.
When you press the Pause(II) button again while the playback is paused, it will
resume the playback.
When playing,
When you press the REW(◄◄) button, the previous music file will be played.
When you press the FF(►►) button, the next music file will be played.
II
◄◄ / ►►
Start playing the selected music files and then move to the Photo List.
GREEN
TO USE A USB DEVICE
Press the ENERGY SAVING button repeatedly to change the brightness of
your screen.(Refer to p. 82)
Only Off/Screen Off operates from the Movie List, Photo List, Music List.
MENU
or
Home
BACK
EXIT
<>
68
or
Q.MENU
Show the Option menu.
■■ When you press the Back button while the music is playing, the music player currently playing will be hidden and only the music list will be displayed.
■■ When
music
■■ When
music
you press the Exit button while the Music player is displayed, only the
will be stopped and the player will not return to normal TV viewing.
you press the Exit button while the music is stopped or while the
player is hidden, the player will return to normal TV viewing.
■■ When using the < or > button during playback a cursor indicating the position
can be played.
■■When you select the Set Audio Play,
Set Audio Play.
Repeat
◄
On
►
Random
◄
Off
►
Previous
2
Select Repeat or Random.
Make appropriate adjustments.
TO USE A USB DEVICE
1
69
TO USE A USB DEVICE
■■When you select the Set Audio,
Set Audio.
Sound Mode
◄
Standard
►
Auto Volume
◄
Off
►
Clear Voice II
◄
Off
►
Balance
0
◄
L
R ►
Previous
TO USE A USB DEVICE
70
1
2
Select Sound Mode, Auto Volume, Clear Voice II or Balance.
Make appropriate adjustments. (Refer to p. 94 to 98)
■■ If you don't press any button for a while during the playing, the
play information box (as shown in the below) will float as a
screen saver.
■■ The ‘Screen Saver’?
Screen saver is to prevent screen pixel damage due to an
fixed image remaining on the screen for a extended period of
time.
002. B02.mp3
► 00:31 / 04:04
NOTE
TO USE A USB DEVICE
►►A damaged or corrupted music does not play but displays 00:00 in playtime.
►►A music downloaded from a paid service with copyright protection does not start but displays inappropriate
information in playtime.
►►If you press OK, ■ buttons, screen saver is stopped.
►►The PLAY(►), Pause(II), ■ , ►►, ◄◄ buttons on the remote control are also available in this mode.
►►You can use the ►► button to select the next music and the ◄◄ button to select the previous music.
71
TO USE A USB DEVICE
EXTRA CONTENTS
You can play application file on USB device.
Application file on your USB device can be played by this unit.
The On Screen Display may be different from your TV. Images are an example to assist with the TV
operation.
FLASH (*.SWF) / GEM supporting file
An SWF file complied with Flash Lite 3.0 or earlier (the 3.0 version is recommended)
TO USE A USB DEVICE
•T
he Pro:Centric application is required, which starts automatically in the flash memory when the
TV is turned on.
• The folder called /hcapfs/as/abs_service/ must exist in USB drive root directory.
• The file called xait.xml must exist in the /hcapfs/as/abs_service/ folder.
• If the above conditions are not met, the following error message is displayed when selecting the
Extra Contents: Failed to execute file in the USB. Please check the file in the USB.
•W
hen the flash file does not run even if the above all conditions are met, refer to the Download Extra
Contents of Installation Guide.
•G
EM is composed of JAVA application.
■■When playing Application file
1
MENU
2
3
or
Home
Select MY MEDIA.
Select Extra Contents.
Application file is played.
■■To stop playing the Application file
Remove the USB from the USB IN jack of the TV set.
NOTE
►When
►
playing the Application file(FLASH or GEM file), the buttons are controlled according to
the settings of the Extra Contents option.
72
DIVX REGISTRATION CODE
Confirm the DivX registration code number of the TV. Using the registration number, movies can be
rented or purchased at www.divx.com/vod.
With a DivX registration code from other TV, playback of rented or purchased DivX file is not allowed.
(Only DivX files matched with the registration code of the purchased TV are playable.)
MY MEDIA
DivX Reg. Code
Deactivation
Movie List
Photo List
Press OK(
Music List
2
3
BLUE
Home
Exit
Select MY MEDIA.
Select DivX Reg. Code.
Display DivX Reg. Code.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
TO USE A USB DEVICE
or
MENU
Close
) to see photos from the USB.
Option
1
Previous
Extra Contents
You must register your device to
play DivX protected videos.
Registration code : **********
Register at http://vod.divx.com
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is
an official DivX Certified® device that plays DivX video. Visit www.divx.com for
more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain
your registration code, locate the DivX VOD section in your device setup menu.
Go to vod.divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
DivX®, DivX Certified® and associated logos are trademarks of DivX, Inc. and are
used under license.
Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668;
7,515,710; 7,519,274
NOTE
►Movie
►
files are supported as follows
Resolution : under 1920x1080 WxH pixels
Frame rate : under 30 frames/sec(1920x1080), under 60 frames/sec(under 1280x720)
►Video
►
Codec : MPEG 1, MPEG 2, MPEG 4, H.264/AVC, DivX 3.11, DivX 4.12, DivX 5.x, DivX 6,
Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1, Xvid 1.10-beta2, JPEG, VC1,
Sorenson H.263/H.264
73
TO USE A USB DEVICE
DEACTIVATION
The purpose of deactivation is to allow deactivation of devices for users who have activated all the
available devices through the web_server and are blocked from activating more devices. DivX VOD
allowed the consumer to activate up to 6 devices under one account, but to replace or deactivate any
of those devices, the consumer had to contact DivX Support and request deletion. Now with this
added feature, consumers will be able to deactivate the device themselves and hence better manage
their DivX VOD devices.
MY MEDIA
DivX Reg. Code
Deactivation
Movie List
Photo List
Press OK(
Music List
TO USE A USB DEVICE
or
MENU
2
3
4
BLUE
Yes
No
) to see photos from the USB.
Option
1
Previous
Extra Contents
Deregistration code :
********
Deregister at http://vod.divx.com
Continue with registration?
Home
Exit
Select MY MEDIA.
Select Deactivation.
Select Yes.
Display Deactivation.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
74
EPG(ELECTRONIC PROGRAMME GUIDE)
(IN DIGITAL MODE)
This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible
viewing options.
The EPG supplies information such as programme listings, start and end times for all available services. In
addition, detailed information about the programme is often available in the EPG (the availability and
amount of these programme details will vary, depending on the particular broadcaster).
This function can be used only when the EPG information is broadcast by broadcasting companies.
You must set the Clock in the Time menu, before using EPG function.
The EPG displays the programme details for 8 days.
►
DTV 1 TV ONE
►
Pr. Change
► Next
Watch
Good Morning
21:00
00:00
Show/Game Show
16:9 720p
... HE-AAC
Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,
with regular and special guests.
Sarah Bradley, Steve Gray and Brendon Pongia present the latest in fashion, the arts, entertainment, lifestyle and cooking,
with regular and special guests.
▼
INFO
Up
Down
Shows current programme information
Displayed with a Teletext Programme.
Displayed with a Radio Programme.
Displayed with a Subtitle Programme.
Displayed with a MHEG Programme.
Displayed with a Scramble Programme.
Displayed with a HE-AAC Programme.
Displayed with a Dolby Digital Programme.
Aspect ratio of broadcasting programme.
Displayed with a Dolby Digital Plus Programme.
Aspect ratio of broadcasting programme.
576i/p, 720p, 1080i/p : Resolution of broadcasting programme
Broadcasted programme with the icon may not be displayed in Monitor Out depending on the information of the programme.
Shows next programme information.
Shows other programme information.
Tyra
2 TV2
◄ Now
Schedule
Remind
Tyra
21:00
Pr. Change
►
Record
DTV 2 TV2
►
28 Sep. 2008 21:00~00:00
EPG (ELECTRONIC PROGRAMME GUIDE)
(IN DIGITAL MODE)
Displayed with a TV or DTV Programme.
Close
00:00
Show/Game Show
Talk show host Tyra Banks sits down with Keyshia Cole, the cast of Gossip Girl and Rihanna.
Talk show host Tyra Banks sits down with Keyshia Cole, the cast of Gossip Girl and Rihanna.
A pop-up window for record/remind settings
appear.
Select Timer Record/Remind setting mode.
75
EPG (ELECTRONIC PROGRAMME GUIDE)
Switch on/off EPG
1 GUIDE
Switch on or off EPG.
Select a programme
1
or
Select desired programme.
Button Function in NOW/NEXT Guide Mode
You can view a programme being broadcasted and one scheduled to follow.
EPG (ELECTRONIC PROGRAMME GUIDE)
(IN DIGITAL MODE)
76
RED
Change EPG mode.
Programme Guide
▲
That ’70s show
25 Nov. 2008 10:05
DTV 1 YLE TV1 25 Nov. 2008 09:45~10:15
When ‘NOW’ is selected, it is moved to
selected programme and EPG disappears.
ALL
Page Up/Down.
NEXT
That ’70s show
2 YLE TV2 Your World Today
4 TV..
Legenen om Den....
5 YLE FST Naturtimmen
6 CNN
Lyssna
8 YLE24
Glamour
Select NOW or NEXT Programme.
Select the Broadcast Programme.
NOW
1 YLE TV1
INFO i Information
Keno
World Business
Fantomen
Kritiskt
ABC
Tänään otsikoissa
▼
Watch
TV/RAD RADIO
Mode
GUIDE
or
BACK
or
Switch off EPG.
Select DTV or RADIO Programme.
INFO
Detail information on or off.
Button Function in 8 Day Guide Mode
Programme Guide
▲
That ’70s show
Change EPG mode.
ALL
14:00
Kungskonsumente
Antigues Roadshow
The Drum
Mint Extra
TV2: Farmen
The Drum
You Call The Hits
Fashion Essentials
...
... ...
Tänään otsikoissa
2 YLE TV2
Enter Date setting mode.
4 TV..
5 YLE FST
6 CNN
When ‘Currently broadcasting programme’ is selected, it is moved to
selected programme and EPG disappears.
8 YLE24
▼
Watch
TV/RAD RADIO
Date
Page Up/Down.
Select Programme.
Select the Broadcast Programme.
...
INFO i Information
Mode
Tue. 25 Nov.
15:00
▼
1 YLE TV1
GREEN
◄
RED
25 Nov. 2008 10:05
DTV 1 YLE TV1 25 Nov. 2008 09:45~10:15
◄
GUIDE
or
BACK
or
Switch off EPG.
Select DTV or RADIO Programme.
INFO
Detail information on or off.
EPG (ELECTRONIC PROGRAMME GUIDE)
(IN DIGITAL MODE)
77
EPG (ELECTRONIC PROGRAMME GUIDE)
Button Function in Date Change Mode
Programme Guide
or
BACK
Switch off Date setting mode.
25 Nov. 2008 10:05
DTV 1 YLE TV1 25 Nov. 2008 09:45~10:15
◄
ALL
14:00
Change to the selected date.
2 YLE TV2
4 TV..
5 YLE FST
6 CNN
Select a date.
8 YLE24
...
Tue. 25 Nov.
15:00
▼
1 YLE TV1
◄
GREEN or
▲
That ’70s show
Kungskonsumente
Antigues Roadshow
The Drum
Mint Extra
TV2: Farmen
The Drum
You Call The Hits
Fashion Essentials
...
... ...
Tänään otsikoissa
▼
Date Change
GUIDE
EPG (ELECTRONIC PROGRAMME GUIDE)
(IN DIGITAL MODE)
78
or
Switch off EPG.
Date Exit
Button Function in Extended Description Box
INFO
The detail information on or off.
Text Up/Down.
GUIDE
or
Switch off EPG.
DTV 1 YLE TV1 25
25 Nov. 2008 10:05
Fia World Touring Car Chanpionship
Tue. 25 Nov. 2008 10:05
12:40
Fia Champion
Miss Gotto's Haunted house/Cry of The Swamp; Miss Gotto's
Haunted house/Cry of The Swamp; Miss Gotto's Haunted
house/Cry of The Swamp; Miss Gotto's Haunted house/Cry
of The Swamp; Miss Gotto's Haunted house/Cry of The
Swamp; Miss Gotto's Haunted house/Cry of The Swamp;
Close
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO) CONTROL
You can watch the screen in various picture formats; 16:9, Just Scan,
Original, Full Wide, 4:3, 14:9, Zoom and Cinema Zoom.
If a fixed image is displayed on the screen for a long time, that fixed
image may become imprinted on the screen and remain visible.
You can adjust the enlarge proportion using
button.
This function works in the following signal.
1
Q.MENU
2
Select Aspect Ratio.
•Y
ou can also adjust Aspect Ratio in the
PICTURE menu.
•F
or Zoom Setting, select 14:9, Zoom and
Select the desired picture format.
• Original
When your TV receives a wide screen signal it will automatically change to the picture format broadcast.
Original
• Just Scan
Following Selection will lead to you view the
picture of best quality without loss of original
picture in high resolution image.
Note : If there is noise in original Picture, You
can see the noise at the edge.
Just Scan
PICTURE CONTROL
• 16:9
The following selection will allow you to adjust the picture horizontally, in linear proportion, to fill the entire
screen(useful for viewing 4:3 formatted DVDs).
Cinema Zoom in Ratio Menu. After completing Zoom Setting, the display goes
back to Q.Menu.
• Full Wide
When TV receives the wide screen signal,it will lead
you to adjust the picture horizontally or vertically, in
a linear proportion,to fill the entire screen fully.
4:3 and 14:9 video is supported in full screen without any video distortion through DTV input.
Full Wide
79
PICTURE CONTROL
• 4:3
The following selection will allow you to view a picture
with an original 4:3 aspect ratio.
• Zoom
The following selection will allow you to view
the picture without any alteration, while filling
the entire screen. However, the top and bottom
of the picture will be cropped.
• 14:9
You can view a picture format of 14:9 or a general TV
programme in the 14:9 mode. The 14:9 screen is
viewed in the same way as in 4:3, but is moved to the
up and down.
• Cinema Zoom
Choose Cinema Zoom when you want to
enlarge the picture in correct proportion.
Note:When enlarging or reducing the picture,
the image may become distorted.
PICTURE CONTROL
◄ or ► button: Adjust enlarge proportion of
Cinema Zoom. The adjustment range is 1 to 16.
▼ or ▲ button: Move the screen.
NOTE
►►You can only select 4:3, 16:9 (Wide), 14:9, Zoom/Cinema Zoom in Component mode.
►►You can only select 4:3, Original, 16:9 (Wide), 14:9, Zoom/Cinema Zoom in HDMI mode.
►►You can only select 4:3, 16:9 (Wide) in RGB-PC, HDMI-PC mode only.
►►In DTV/HDMI/Component (over 720p) mode, Just Scan is available.
►►In Analogue/DTV/AV/Scart mode, Full Wide is available.
80
PICTURE WIZARD
This feature lets you adjust the picture quality of the original image.
Use this to calibrate the screen quality by adjusting the Black and White Level etc. General users can
calibrate the screen quality by easily following each stage.
When you adjust the image to Low, Recommended or High, you can see the changed result as an
example.
In RGB-PC/HDMI-PC/DVI-PC mode, the changed Colour, Tint and H/V Sharpness values are not
applied.
PICTURE
● Aspect
Ratio
Move
With Picture Wizard, you can adjust the picture quality of the
original image.
: 16:9
MENU
or
2
3
4
: Standard
• Backlight
70
• Contrast
100
• Brightness
50
• Sharpness
70
Home
Previous
Select PICTURE.
Select Picture Wizard.
Adjust Standard(Black Level, White Level,
Tint, Colour, Horizontal Sharpness, Vertical
Sharpness, Backlight) or Preferred(Black
Level, White Level, Tint, Colour, Sharpness,
Dynamic Contrast, Colour Temperature,
Backlight).
CHAR/NUM
MARK
5
: Off
Select input source to apply the settings.
Next
• If you stop the setting before
the final stage, the changes
will not be applied
• The adjustment value is
saved to Expert1.
• Once the Picture Wizard sets
the image quality, the Energy
Saving is changed into Off.
• If the picture quality setting
of Expert1 is changed, use
the Picture Reset before
entering the Picture Wizard
to reset the picture quality
setting.
• Standard : mode to set standard picture quality.
• Preferred : mode to set user
preferred picture quality rather than standard picture.
PICTURE CONTROL
1
Mode
►
Energy Saving
● Picture
►
● Picture Wizard
●
Picture Wizard
OK
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
81
PICTURE CONTROL
ENERGY SAVING
It reduces the TV’s power consumption.
The default factory setting is adjusted to the comfortable level to be viewed at home.
You can increase the brightness of your screen by adjusting the Energy Saving level or by setting
the Picture Mode.
When adjusting Energy Saving in MHEG/MHP mode, the Energy Saving setting is applied after
MHEG/MHP is finished.
Selecting ‘Screen Off’ while tuned to a radio station channel will reduce power consumption.
PICTURE
Ratio
● Picture
Wizard
●
●
MENU
2
3
or
Home
Select
Mode
: Off
: Standard
• Backlight
70
• Contrast
100
• Brightness
50
• Sharpness
70
Auto
Off
Off
►
PICTURE CONTROL
1
: 16:9
ꕊ Energy
Saving: Off
Energy
Saving
● Picture
OK
►
● Aspect
Move
Minimum
Medium
Maximum
Screen Off
Select PICTURE.
Energy Saving.
Select Auto, Off, Minimum , Medium,
Maximum or Screen Off.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
• When you select Screen Off, the screen will be turned off in 3 seconds and Screen Off will start.
• If you adjust “Energy Saving-Auto, Maximum”, Backlight feature will not work.
• You can also adjust this feature by selecting Energy Saving button on the remote control.
• When selecting Auto, Backlight is automatically adjusted through intelligent sensor according to the
surrounding condition when intelligent sensor is in the TV.
82
PRESET PICTURE SETTINGS
Picture Mode-Preset
Vivid
Standard
Cinema
Sport
Game
Strengthen the contrast, brightness, colour and sharpness for vivid picture.
The most general screen display status.
Optimizes video for watching movies.
Optimizes video for watching sports events.
Optimizes video for playing games.
PICTURE
Ratio
● Picture
Wizard
●
Energy Saving
●●Picture
Mode
Picture
Mode
OK
: 16:9
Intelligent Sensor
: Off
Vivid
Standard
::Standard
70
• Contrast
100
• Brightness
50
• Sharpness
70
Standard
Standard
►
• Backlight
►
● Aspect
Move
Cinema
Sport
Game
ꕋ Expert1
ꕋ Expert2
MENU
2
3
or
Home
Select PICTURE.
Select Picture Mode.
Select Intelligent Sensor, Vivid, Standard, Cinema,
Sport or Game.
PICTURE CONTROL
1
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
• Picture Mode adjusts the TV for the best picture appearance. Select the preset value in the
Picture Mode menu based on the programme category.
• When the Intelligent sensor function is on, the most suitable picture is automatically adjusted
according to the surrounding conditions.
• You can also adjust Picture Mode in the Q. Menu.
• Intelligent Sensor : Adjusts picture according to the surrounding conditions.
83
PICTURE CONTROL
MANUAL PICTURE ADJUSTMENT
Picture Mode-User option
Backlight
To control the brightness of the screen, adjust the brightness of LCD panel.
Adjusting the backlight when setting the brightness of the set is recommended.
Contrast
Adjusts the signal level between black and white in the picture. You may use Contrast when the bright
part of the picture is saturated.
Brightness
Adjusts the base level of the signal in the picture.
Sharpness
Adjusts the level of crispness in the edges between the light and dark areas of the picture.
The lower the level, the softer the image.
Colour
Adjusts intensity of all colours.
Tint
Adjusts the balance between red and green levels.
Colour Temp.
Adjust to left direction to make a picture reddish or adjust to right direction to make a picture bluish.
It is not available to use this function in “Intelligent Sensor”.
PICTURE
Ratio
● Picture
Wizard
●
Energy Saving
●●Picture
Mode
Picture
Mode
OK
: 16:9
Intelligent Sensor
: Off
Vivid
Standard
::Standard
70
• Contrast
100
PICTURE CONTROL
• Brightness
50
• Sharpness
70
Standard
Standard
►
• Backlight
►
● Aspect
Move
Cinema
Sport
Game
ꕋ Expert1
ꕋ Expert2
1
MENU
2
3
4
5
or
Home
Select PICTURE.
Select Picture Mode.
Select Vivid, Standard, Cinema, Sport or Game.
Select Backlight, Contrast, Brightness,
Sharpness, Colour, Tint or Colour Temp..
Make appropriate adjustments.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
84
• Benefits of using Backlight
- The electricity consumption is reduced by up to 60 %.
- The black brightness is reduced. (As the black has greater depth, you can enjoy a better quality
definition.)
- You can adjust brightness with maintaining original signal resolution.
NOTE
►You
►
cannot adjust colour, sharpness and tint in the RGB-PC/HDMI-PC mode.
►►When the Expert 1/2 is selected, you can select Backlight, Contrast, Brightness, H Sharpness,
V Sharpness, Colour or Tint.
PICTURE CONTROL
85
PICTURE CONTROL
PICTURE IMPROVEMENT TECHNOLOGY
You can calibrate the screen for each Picture Mode or set the video value according to the special
video screen.
You can set the video value differently for each input.
To reset to the factory default screen after making adjustments to each video mode, execute the
“Picture Reset” function for each Picture Mode.
■ Image shown may differ from your TV.
PICTURE
Move
• Brightness
50
• Sharpness
70
• Colour
60
PICTURE
OK
• Tint
0
R
G
• Colour Temp.
0
W
C
Move
OK
Dynamic Contrast
Dynamic Colour
• Brightness
50
R
Clear White
• Sharpness
70
W
• Colour Skin Colour
60
• Tint
G
High
C
Noise Reduction
0 R
0
G
Medium
C
Medium
• Advanced Gamma
Control
• Picture Reset
• Screen
• Screen
►
High
• Colour Temp.
0 WReduction
Digital Noise
• Advanced Control
◄ High
Medium
• Picture Reset
Black Level
Auto
Eye Care
Low
▼
Close
1
PICTURE CONTROL
MENU
2
3
4
or
Home
Select PICTURE.
Select Advanced Control.
Select your desired Source.:
Dynamic Contrast, Dynamic Colour, Clear White, Skin Colour, Noise
Reduction, Digital Noise Reduction, Gamma, Black Level, Eye Care, Real
Cinema, Colour Gamut or xvYCC. (Refer to p. 88 to 89)
Make appropriate adjustments.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
86
EXPERT PICTURE CONTROL
By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they
see fit, offering the optimal picture quality for users.
This may also be used to help a professional optimize the TV performance using specific videos.
■ Image shown may differ from your TV.
PICTURE
● Aspect
Ratio
● Picture
Wizard
●
Move
PICTURE
OK
Mode
Picture
Mode
●●Picture
: Off
::
OK
◄ Off
Expert1 Standard
Standard
• Backlight
70
Cinema
• Contrast
90
Sport
• Brightness
50
Game
Off
• V Sharpness 60 R
Black Level
• Colour
60
Real Cinema
Tint Control 0
•• Expert
Colour Gamut
• Advanced Control
Edge
Enhancer
• Picture
Reset
Vivid
• Screen
• H Sharpness ꕋ
70 Expert1
Expert1
G
Auto
On
Standard
High
xvYCC
Auto
Expert Pattern
Expert2
►
Off
• H Sharpness
Digital Noise 70
Reduction
Intelligent Sensor
Energy Saving
Move
Dynamic Contrast
• Brightness
Noise Reduction
: 16:9
Off
▼
Close
MENU
2
3
4
5
6
or
Home
Select PICTURE.
Select Picture Mode.
Select
Expert1 or
Expert2.
Select Expert Control.
PICTURE CONTROL
1
Select your desired Source.
Make appropriate adjustments.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
87
PICTURE CONTROL
*This feature is not available for all models.
Dynamic Contrast
(Off/Low/Medium/High)
Dynamic Colour
(Off/Low/High )
■■ Adjusts the contrast to keep it at the best level according to the brightness of
the screen. The picture is improved by making bright parts brighter and dark
parts darker.
■■ Adjusts screen colours so that they look livelier, richer and clearer. This feature enhances hue, saturation and luminance so that red, blue, green and
white look more vivid.
Skin Colour
■■ Adjusts skin colour of the picture so that user can set his favourite skin
colour.
(-5 to 5)
Noise Reduction
(Off/Low/Medium/High/ ■■ Reduces screen noise without compromising video quality.
Auto(In Analogue Mode
Only))
Digital Noise Reduction
■■ Reduces noise regarding MPEG compressed video.
(Low/Medium/High/Off)
Gamma
(Advanced Control:
Low/Medium/High
Expert Control:
1.9/2.2/2.4)
PICTURE CONTROL
Black Level
(Low/High/Auto)
Clear White
(Off/Low/High)
Eye Care
(Low/High/Off)
Real Cinema
(On/Off)
88
■■ You can adjust brightness of dark area and middle gray level area of the picture.
• Low/1.9 : Makes dark and middle gray level area of the picture brighter.
• Medium/2.2 : Expresses original picture levels.
• High/2.4: Makes dark and middle gray level area of the picture darker.
• Low : The picture of the screen gets darker.
• High : The picture of the screen gets brighter.
• Auto : Sets black level of the screen to High or Low automatically according to
the input signal level.
■■ This function enables to select 'Low' or 'High' in the following mode:
AV(NTSC-M), HDMI or Component. Otherwise, 'Black level' is set to 'Auto'.
■■ Makes the white area of the screen brighter and clearer.
*This feature is not available for all models.
■■ Adjusts the brightness of the screen automatically to the best level for
eyes when the screen is too bright.
■■ This feature is disable in “Picture Mode-Vivid, Cinema, Expert1,
Expert2, Intelligent Sensor”.
■■ You can watch a cinema-like video by eliminating judder effect.
■■ Uses this function when you watch film-originated movie contents.
■■ This function can work when TruMotion is off. (Only 47LD6***)
Colour Gamut
(Advanced Control)
(Wide/Standard)
• Standard : Mode to use original colour area regardless of the display char-
acteristics.
• Wide: Mode to use maximum colour area of the TV display.
• Standard : Mode to use original colour area regardless of the display char-
acteristics.
• Wide : Mode to use maximum colour area of the TV display.
• EBU : Mode to display EBU colour area.
• SMPTE : Mode to display SMPTE colour area.
• BT709 : Mode to display BT709 colour area.
Edge Enhancer
■■ Makes the edge of the picture clearer and distinctive.
(Off/Low/High)
■■ This function can use in “Picture Mode-Expert.”
*This feature is not available for all models.
xvYCC
■■ This is the function to express richer colour.
(Auto/off/on)
■■ This function is enabled in "Picture mode - Cinema, Expert" when xvYCC signal is inputted through HDMI
Expert Pattern
■■ This is the pattern necessary for checking the picture of Digital TV.
(Off/Pattern1/Pattern2) ■■ This function is enabled in "Picture Mode - Expert" when you watch DTV.
Colour Filter
■■ This is the function to filter the specific colours of the video.
(Off/Red/Green/Blue) You can use the RGB filter to set colour saturation and hue accurately.
Colour Gamut
(Expert Control)
(EBU/SMPTE/BT709/
Wide/Standard)
Colour Management
System
PICTURE CONTROL
Colour Temperature
(Medium/Warm/Cool)
This is the function to adjust the overall colour of the screen to the feeling you want.
a. • Method : 2 Points
• Pattern: Inner, Outer
• Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 to +50.
b. • Method : 10 point IRE
• Pattern: Inner / Outer
• IRE (Institute of Radio Engineers) is the unit to display the size of the video signal and can be set among 10, 20, 30 to 100. You can adjust Red, Green or Blue
according to each setting.
• Luminance: This function displays calculated luminance value for 2.2 gamma.
You can input luminance value you want at 100 IRE, than the target luminance
value for 2.2 gamma is displayed at every 10 steps from 10 IRE to 90 IRE.
• Red/Green/Blue: The adjustment range is -50 to +50.
■■ As the tool used by the experts to make adjustments by using the test patterns, this does not affect other colours but can be used to selectively
adjust the 6 colour areas (Red/Green/Blue/Cyan/Magenta/Yellow).
Colour difference may not be distinctive even when you make the adjustments for the general video.
■■ Adjusts Red/Green/Blue/Yellow/Cyan/Magenta.
• Red/Green/Blue/Yellow/Cyan, Magenta Colour : The adjustment
range is -30 to +30.
• Red/Green/Blue/Yellow/Cyan/Magenta Tint : The adjustment
range is -30 to +30.
■■ This feature is disable in RGB-PC and HDMI (PC) mode.
89
PICTURE CONTROL
PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
■ Image shown may differ from your TV.
PICTURE
Move
PICTURE
OK
• Brightness
50
• Sharpness
70
• Sharpness
70
• Colour
60
• Colour? All picture
60 settings will be reset.
G
• Tint
0 R
Continue?
0
R
G
0
W
C
3
4
0
• Picture Reset
• Picture Reset
►
• Advanced Control
C
W
Yes
No
►
2
• Colour Temp.
• Advanced Control
►
• Tint
• Colour Temp.
►
PICTURE CONTROL
MENU
OK
50
• Screen
• Screen
1
Move
• Brightness
or
Home
Select PICTURE.
Select Picture Reset.
Select Yes.
Initialize the adjusted value.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
90
TRUMOTION
(Only 47LD6***)
It is used for the best picture quality without any motion blur or judder when you enter a quick image
or Film Source.
High : Provide smoother picture movement.
Low : Provide smooth picture movement. Use this setting for standard use.
Off : Turn off TruMotion Operation.
User : User can adjust Judder and Blur level in TruMotion Operation, separately.
- Judder : Adjust noise of the screen.
- Blur : Adjust after-image of the screen.
This feature is disable in RGB-PC,HDMI-PC mode.
If you enable "TruMotion", noise may appear on the screen.
If this occurs, set "TruMotion" to "Off".
If you select “Picture Mode-Game ”, set “TruMotion" to "Off".
PICTURE
Move
• Sharpness
70
• Colour
60
OK
TruMotion
• Tint
0
R
G
• Colour Temp.
0
W
C
• Advanced Control
• Picture Reset
3
● Blur
3
►
OK
►
• •TruMotion
TruMotion
◄ Low
● Judder
►
: Off
• Screen
MENU
2
3
4
or
Select PICTURE.
Home
Select TruMotion.
PICTURE CONTROL
1
Select Low, High, User or Off.
Make appropriate adjustments.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
91
PICTURE CONTROL
DEMO MODE
The screen is reset automatically after 5 minutes in Demo Mode.
4
►
● Language(Language)
● Country
: UK
● Disability Assistance
● Disability Assistance
● Power
● Power
Indicator
Reset
ID
Home
● Set
ID
: UK
Indicator
● Factory
:1
On
OK
►
3
Move
OnOff
:: On
►
PICTURE CONTROL
2
or
Demo Mode
Mode
●●Demo
● Country
● Set
MENU
OPTION
OK
● Language(Language)
● Factory
1
Move
On
:: On
►
Demo Mode
Mode
●●Demo
►
OPTION
Reset
:1
Select OPTION.
Select Demo Mode.
Select On.
Move to the previous menu screen.
If you want to stop the demo, press any button. (Except for MUTE,
+ , - button)
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
92
POWER INDICATOR
Adjust the power/standby indicator light on the front of the TV.
Standby Light
Determines whether to set the indicator light on the front of the TV to On or Off in standby mode.
Power Light
Determines whether to set the indicator light on the front of the TV to On or Off when the power turns on.
OPTION
● Demo
● Country
● Power Indicator
● Power Indicator
or
Reset
ID
● Factory
:1
Home
● Set
ID
: UK
Standby Light
◄
Power Light
►
● Disability Assistance
►
● Disability Assistance
OK
Off
►
On
Reset
:1
Close
Select OPTION.
Select Power Indicator.
Select Standby Light or Power Light.
Select your desired Source.
PICTURE CONTROL
4
Move
: On
►
3
Mode
● Language(Language)
: UK
►
2
● Demo
● Country
● Set
MENU
OPTION
OK
: On
● Language(Language)
● Factory
1
Move
Mode
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
93
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER
Auto Volume automatically remains on the same level of volume if you change programmes.
Because each broadcasting station has its own signal conditions, volume adjustment may be needed
every time the programme is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each programme.
If sound quality or volume is not at the level you want, it is recommended to use a separate home theater system or amp to cope with different user environments.
AUDIO
Move
● Clear
Voice II
: Off
3
● Balance
● Sound
1
MENU
2
SOUND & LANGUAGE CONTROL
3
Mode
AUDIO
OK
: Off
● Auto
● Clear
0
L
R
: Standard
Move
Volume
Voice II
: Off
● Balance
● Sound
Mode
3
On
0
L
R
: Standard
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
or
OK
MHEG
Off
: Off
►
Volume
►
● Auto
Select AUDIO.
Home
Select Auto Volume.
Select On or Off.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
94
CLEAR VOICE II
By differentiating the human sound range from others, it helps users listen to human voices better.
AUDIO
Volume
● Auto
: Off
Off
:: Off
33
● Balance
● Sound
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
MENU
or
R
● Sound
Select AUDIO.
Home
Off
:: Off
Mode
OK
● Clear
33
L
0 ● Level
Voice II
R
◄
3
Off
-
5
+
: Standard
• Infinite Sound : Off
• Treble
50
• Bass
50
• Reset
Close
• If you select “On” for Clear Voice II,
Infinite Sound feature will not work.
• Select levels from ‘-6’ to ’+6’.
Select Clear Voice II.
Select On or Off.
Adjustment for Clear Voice Level With selecting On
4
►
Select Level.
Make desired adjustment.
SOUND & LANGUAGE CONTROL
3
L
: Off
● Balance
: Standard
1
2
Mode
0
Move
Volume
Clear Voice
Voice II
II
●●Clear
►
Clear Voice
Voice II
II
●●Clear
AUDIO
OK
►
● Auto
Move
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
95
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS-SOUND MODE
You can select your preferred sound setting; Standard, Music, Cinema, Sport or Game and you can
also adjust the Treble, Bass.
Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content.
Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory.
Standard
Music
Cinema
Sport
Game
Offers standard-quality sound.
Optimizes sound for listening to music.
Optimizes sound for watching movies.
Optimizes sound for watching sports events.
Optimizes sound for playing games.
AUDIO
Move
Volume
● Clear
Voice II
: Off
SOUND & LANGUAGE CONTROL
2
3
3
Sound Mode
Mode
●●Sound
Standard
:: Standard
L
R
Move
Volume
● Clear
0
Voice II
OK
: Off
: Off
3
● Balance
L
Standard
0 Standard
Standard
:: Standard
• Infinite Sound : Off
• Treble
50
• Infinite Sound : OffCinema
• Treble
50 Sport
• Bass
50
• Bass
• Reset
• Reset
or
Home
Select AUDIO.
R
Music
Sound Mode
Mode
●●Sound
►
MENU
● Auto
►
● Balance
1
AUDIO
OK
: Off
►
● Auto
50 Game
• You can also adjust Sound Mode in
the Q. Menu.
Select Sound Mode.
Select Standard, Music, Cinema, Sport or
Game.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
96
SOUND SETTING ADJUSTMENT -USER MODE
AUDIO
Move
Volume
● Clear
Voice II
: Off
● Auto
3
Sound Mode
Mode
●●Sound
Standard(User)
:: Standard
L
R
Voice II
Move
OK
: Off
: Off
3
L
R
Standard(User)
0 Standard
● Balance
Music
Sound Mode
Mode
●●Sound
Standard(User)
:: Standard
• Infinite Sound : Off
• Treble
50
• Infinite Sound : OffCinema
• Treble
50 Sport
• Bass
50
• Bass
• Reset
• Reset
or
►
2
0
►
MENU
Volume
● Clear
● Balance
1
AUDIO
OK
: Off
►
● Auto
50 Game
Select AUDIO.
Home
Select Sound Mode.
3
Select Standard, Music, Cinema, Sport or
Game.
4
Select Treble or Bass.
5
Set the desired sound level.
INFINITE SOUND
Select this option to sound realistic.
1
MENU
2
3
or
Select AUDIO.
Home
Select Infinite Sound.
Infinite Sound : Infinite Sound is a patented
LG proprietary sound processing technology
that strives immersive 5.1 surround sound
impression with front two loudspeakers.
Select On or Off.
SOUND & LANGUAGE CONTROL
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
97
SOUND & LANGUAGE CONTROL
BALANCE
You can adjust the sound balance of the speakers to preferred levels.
AUDIO
Volume
● Clear
: Off
Voice II
● Auto
: Off
3
1
MENU
2
SOUND & LANGUAGE CONTROL
3
Mode
00
L
R
Move
Volume
● Clear
►
●● Balance
Balance
● Sound
AUDIO
OK
►
● Auto
Move
Voice II
: Off
: Off
●● Balance
Balance
3
0●0LBalance
: Standard
● Sound
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
• Reset
or
Mode
OK
: Standard
R
0◄
L
R
Close
Select AUDIO.
Home
Select Balance.
Make desired adjustment.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
98
►
DTV AUDIO SETTING (IN DIGITAL MODE ONLY)
When different audio types exist in an input signal, this function allows you to select the audio type
you want.
AUDIO
Move
● Balance
● Sound
Mode
0
AUDIO
OK
L
R
● Sound
: Standard
Move
● Balance
Mode
0
OK
L
• Infinite Sound : Off
• Infinite Sound : Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
Auto
Auto
• Reset
HE-AAC
: PCM
Dolby Digital+
: :Auto
Auto
Dolby Digital
Out
DTVAudio
AudioSetting
Setting
●●DTV
• Reset
: PCM
● Digital Audio
Auto
: :Auto
►
● Digital Audio
Out
● DTV Audio Setting
►
R
: Standard
MPEG
1
MENU
2
3
or
Home
Select AUDIO.
Select DTV Audio Setting.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
•Auto: Automatically outputs in the order HE-AAC > Dolby Digital+ > Dolby Digital > MPEG.
(Except for Italy)
Auto: Automatically outputs in the order HE-AAC > Dolby Digital+ > MPEG > Dolby Digital.
(Only Italy)
•HE-AAC, Dolby Digital +, Dolby Digital, MPEG: Allows users to select the audio type they want.
ex) If MPEG is selected, MPEG is always outputted.
If MPEG is not supported, another audio type is set in that order.
• Refer to p. 106 to 107 (Audio Language Selection)
SOUND & LANGUAGE CONTROL
Select Auto, HE-AAC, Dolby Digital +, Dolby
Digital or MPEG.
99
SOUND & LANGUAGE CONTROL
SELECTING DIGITAL AUDIO OUT
This function allows you to select your preferred Digital Audio Output.
When Dolby Digital is available, selecting Auto in the Digital Audio Out menu will set SPDIF(Sony
Philips Digital InterFace) output to Dolby Digital.
If Auto is selected in the digital audio out menu when Dolby Digital is not available, SPDIF output will
be PCM(Pulse-code modulation).
Even if both Dolby Digital and Audio language have been set in a channel which broadcast Dolby
Digital Audio, only Dolby Digital will be played.
● Balance
● Sound
Mode
• Infinite Sound : Off
50
• Treble
50
• Bass
50
• Bass
• Reset
• Reset
50
Auto
PCM
: :PCM
● Digital Audio
►
• Treble
Out
● DTV Audio
Setting : Auto
or
Home
PCM
: :PCM
PCM
PCM
Setting : Auto
Manufactured under license from
Dolby Laboratories. Dolby and the
double-D symbol are trademarks
of Dolby Laboratories.
Select AUDIO.
Select Digital Audio Out.
Select Auto or PCM.
Out
R
: Standard
►
3
Mode
OK
L
• Infinite Sound : Off
►
SOUND & LANGUAGE CONTROL
2
● Sound
: Standard
0
● DTV Audio
MENU
Move
● Balance
R
● Digital Audio
1
0
AUDIO
OK
L
►
Move
►
AUDIO
• There is a possibility that when HDMI mode,
some DVD players do not make SPDIF sound.
At that time, set the output of the digital audio of
the DVD player to PCM. (In HDMI, Dolby Digital
Plus is not supported).
Item
Audio Input
Digital Audio output
Auto(Speaker On)
MPEG
Dolby Digital
Dolby Digital Plus
HE-AAC
PCM
Dolby Digital
Dolby Digital
PCM
Auto(Speaker Off)
MPEG
Dolby Digital
Dolby Digital Plus
HE-AAC
PCM
Dolby Digital
Dolby Digital
Dolby Digital
All
PCM
PCM
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
100
AUDIO RESET
Settings of the selected Sound Mode return to the default factory settings.
AUDIO
Move
● Balance
● Sound
Mode
Mode
0
OK
L
R
: Standard
• Infinite Sound
: Off settings will be resetted.
All audio
• Treble
50
• Treble
• Bass
50
• Bass
: PCM
Home
• Reset
● Digital Audio
Setting : Auto
or
?
● DTV Audio
Out
50
Continue?
50
Yes
►
• Reset
Out
►
• Infinite Sound : Off
►
No
: PCM
Setting : Auto
Select AUDIO.
Select Reset.
Select Yes.
Initialize the adjusted value.
SOUND & LANGUAGE CONTROL
4
● Sound
►
3
Move
● Balance
● DTV Audio
2
R
● Digital Audio
MENU
AUDIO
OK
L
: Standard
1
0
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
101
SOUND & LANGUAGE CONTROL
AUDIO DESCRIPTION (IN DIGITAL MODE ONLY)
This function is for the blind, and provides explanatory audio describing the current situation in a TV
programme in addition to the basic audio.
When Audio Description On is selected, basic audio and Audio Description are provided only for those
programmes that have Audio Description included.
Changes the Audio Description volume
Beeps when a programme with Audio Description information is selected
OPTION
● Demo
Move
Mode
● Country
►
: UK
● Power
Reset
or
:1
Home
● Set
ID
Hard of Hearing(
)
Off
Audio Description
• Volume
Indicator
● Factory
OK
◄
►
Indicator
ID
: UK
● Disability Assistance
►
● Set
SOUND & LANGUAGE CONTROL
3
Move
: On
● Language(Language)
● Factory
2
Mode
● Country
● Power
MENU
● Demo
● Language(Language)
● Disability Assistance
1
OPTION
OK
: On
►
Volume
Beep
Reset
0
• Beep
:1
On
-
►
+
Off
Close
Select OPTION.
Select Disability Assistance.
Select Audio Description.
Adjustment for Audio Description Volume With selecting On
4
5
Select Volume or Beep.
Make desired adjustment.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
102
I/II
STEREO/DUAL RECEPTION (IN ANALOGUE MODE ONLY)
When a programme is selected, the sound information for the station appears with the programme
number and station name.
1
Select Audio or Audio Language.
Q.MENU
2
Select the sound output.
Broadcast
On Screen Display
Mono
MONO
Stereo
STEREO
Dual
DUAL I, DUAL II, DUAL I+II
■■ Language selection for dual language broadcast
If a programme can be received in two languages (dual language), you can switch to DUAL I,
DUAL II or DUAL I+II.
DUAL ISends the primary broadcast language to the loudspeakers.
DUAL IISends the secondary broadcast language to the loudspeakers.
DUAL I+II Sends a separate language to each loudspeaker.
SOUND & LANGUAGE CONTROL
■■ Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the
clarity of sound is improved.
103
SOUND & LANGUAGE CONTROL
NICAM RECEPTION (IN ANALOGUE MODE ONLY)
If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous
Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of broadcast received.
1
SOUND & LANGUAGE CONTROL
104
When NICAM mono is received, you can select NICAM MONO or FM MONO.
2
When NICAM stereo is received, you can select NICAM STEREO or FM MONO.
If the stereo signal is weak, switch to FM MONO.
3
When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II or
NICAM DUAL I+II or FM MONO.
SPEAKER SOUND OUTPUT SELECTION
In AV, Component, RGB and HDMI mode, you can select output sound for the left and
right loudspeakers.
Select the sound output.
L+R: Audio signal from audio L input is sent to the left loudspeaker and audio signal from
audio R input is sent to the right loudspeaker.
L+L: Audio signal from audio L input is sent to left and right loudspeakers.
R+R: Audio signal from audio R input is sent to left and right loudspeakers.
ON-SCREEN MENU LANGUAGE / COUNTRY
SELECTION
The installation guide menu appears on the TV screen when it is switched on for the first time.
1
Select your desired language.
2
Select your country.
* If you want to change Language/ Country selection
1
or
MENU
2
3
4
5
Save.
Home
Select OPTION.
1
or
MENU
Select Language(Language).
2
Select Menu Language.
3
Select your desired language.
4
5
Home
Select OPTION.
Select Country.
Select your country.
Select Yes or No.
Save.
NOTE
►►If you do not finish the set-up Installation Guide by pressing BACK or if you time out on the OSD (On
Screen Display) the installation menu will continuously appear until the set up is completed whenever the
TV is switched on.
►►If you select the wrong local country, teletext may not appear correctly on the screen and some problems
may occur during teletext operation.
►►The CI (Common Interface) function may not be applied based on country broadcasting circumstances.
►►DTV mode control buttons may not function based on country broadcasting circumstances.
►►In country that Digital broadcasting regulation isn’t fixed, some DTV function may not work depending on
digital broadcasting circumstances.
►►The Country Setting "UK" should only be activated in UK.
►►If the country setting is set to "--", European terrestrial digital standard broadcasting programmes are available, but some DTV functions may not work properly.
SOUND & LANGUAGE CONTROL
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
105
SOUND & LANGUAGE CONTROL
LANGUAGE SELECTION
The Audio function allows selection of a preferred language.
If audio data in a selected language is not broadcast, the default language audio will be played.
Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a
selected language is not broadcast, the default language subtitle will be displayed.
When the languages you selected as the primary for Audio Language and Subtitle Language and Text
Language are not supported, you can select language in secondary category.
In Digital mode, use the Text language function when two or more Text languages are broadcast. If teletext
data in a selected language is not broadcast, the default Text language page will be displayed.
1
or
MENU
2
Select Language(Language).
3
Select Audio Language, Subtitle
Language or Text Language(Except
for UK).
4
SOUND & LANGUAGE CONTROL
106
5
Home
Select OPTION.
Select your desired language.
1
MENU
2
3
4
or
Home
Select OPTION.
Select Disability Assistance.
Select Hard of Hearing(
).
Select On or Off.
Save.
• Press the BACK button to move to the previous menu screen.
Audio Language OSD Information
< Audio Language Selection >
►►When two or more audio languages are broadcast, you can
select the audio language.
1
Q.MENU
2
Display
N.A
Status
Not Available
MPEG Audio
Dolby Digital Audio
Audio for “Visual Impaired”
Audio for “Hearing Impaired”
Select Audio or Audio Language.
Dolby Digital Plus Audio
HE-AAC Audio
Select an audio language.
< Subtitle Language Selection >
►►When two or more subtitle languages are broadcast, you
can select the subtitle language with the SUBTITLE button
on the remote control.
►►Press the
button to select a subtitle language.
Subtitle Language OSD Information
Display
N.A
Status
Not Available
Teletext Subtitle
Subtitle for “Hard of Hearing”
- The audio/subtitles can be displayed in a simpler form with 1 to 3 characters broadcast by the service provider.
- When you select supplementary Audio (Audio for “Visual/Hearing Impaired”) the TV may output a part of
the Main audio.
SOUND & LANGUAGE CONTROL
107
TIME
SETTING
TIME SETTING
CLOCK SETUP
The clock is set automatically when receiving a digital signal in Auto mode. You can set the clock
manually in Manual mode.
You must set the time correctly before using on/off timer function.
The TV time is set by the time offset information based on Time Zone and GMT (Greenwich Mean
Time) which is received with the broadcast signal and the time is set automatically by a digital signal.
When if the city name in Time Zone is changed into offset, you can change time by 1 hour.
Time Zone menu can be changed in Auto mode.
TIME
Move
TIME
OK
Move
● Clock
►
● Clock
● Off
Time
: Off
● Off
Time
● On
Time
: Off
● On
Time
: Off
● Sleep
● Sleep
Timer
● Alarm
: Off
● Automatic
Timer
● Alarm
Standby : 4 hours
● Automatic
◄Move
: Off
Date
: Off
Month
: Off
Year
: Off
OK
OK
►
Auto
3
Mar.
2008
Standby : 4 hours
Hour
16
Minute
09
Time Zone
London
GMT
Close
1
MENU
2
3
TIME SETTING
4
5
or
Home
Select TIME.
Select Clock.
Select Auto or Manual.
Select either the year, month, date,
time or Time Zone option.
Set the year, month, date, time or Time
Zone option.
Time Zone
Moscow, Samara
Yekaterinburg
Omsk
Krasnoyarsk
Irkutsk
Yakutsk
Vladivostok
Magadan, Kamchatka
Kaliningrad
This Table means the Time Zone table of 9
area of Russia, and when the user selects the
Time Zone for his or her area, it automatically
sets the time for the corresponding area.
However, even though the user selected his
or her area, if the broadcasting station’s
local time offset is not offered, or if the
region information does not match, then the
user may select the Offset from the Time
Zone to set the correct time.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
108
AUTO ON/OFF TIME SETTING
The Off time function automatically switches the TV to standby at a preset time.
Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed.
The Off time function overrides the On time function if both are set to the same time.
The TV must be in standby mode for the On time to work.
TIME
Move
TIME
OK
● Clock
● Clock
Time
: Off
● Off
● On Time
: Off
● On Time
● Sleep
: Off
● Sleep
: Off
● Alarm
● Automatic
►
Timer
● Alarm
►
● Off
Move
Standby : 4 hours
Time
Timer
● Automatic
OK
1 Mar 2007 16:09
: Off
Repeat
◄
Off
: Off
Hour
00
: Off
Minute
00
: Off
Standby : 4 hours
Input
►
Antenna
Programme
TV1
Volume
30
Close
1
MENU
2
3
5
6
Select TIME.
Home
Select Off Time or On Time.
•T
o cancel On/Off Time function, select Off.
•F
or On Time function only
1
2
Select Repeat.
Select Off, Once, Daily, Mon. ~ Fri.,
Mon. ~ Sat., Sat. ~ Sun. or Sun..
Set the hour.
3
4
Select Input.
Select the input source.
Set the programme.
Adjust volume level at switch-on.
TIME SETTING
4
or
Set the minutes.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
109
TIME SETTING
SLEEP TIMER SETTING
You do not have to remember to switch the TV off before you go to sleep.
The sleep timer automatically switches the TV to standby after the preset time has elapsed.
1
Q.MENU
2
Select Sleep Timer.
Select Off, 10, 20, 30, 60, 90, 120, 180 or 240 min.
•W
hen you switch the TV off, the preset sleep timer is cancelled.
•Y
ou can also adjust Sleep Timer in the TIME menu.
TIME SETTING
110
ALARM SETTING
The alarm sound will go off when the designated time passes.
When 60 seconds pass, the alarm sound will stop.
If you do not want Alarm function, select Off.
TIME
Move
TIME
OK
● Clock
Move
● Off
Time
: Off
● Off
Time
: Off
● On
Time
: Off
● On
Time
: Off
: Off
● Sleep
● Automatic
: Off
1 Mar 2007 16:09
: Off
Alarm
◄
Off
● Automatic Standby : 4 hours
Hour
00
● Alarm
Standby : 4 hours
►
: Off
►
●● Alarm
Alarm
Timer
►
Timer
►
● Sleep
OK
● Clock
Minute
►
00
Close
1
MENU
2
3
5
Select TIME.
Home
Select Alarm.
•W
hen alarm operates in standby mode, press
the any button to stop alarm.
• When alarm operates in power on mode, press
the OK button to stop alarm.
Select On.
Set the hour.
Set the minutes.
TIME SETTING
4
or
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
111
TIME SETTING
AUTOMATIC STANDBY
(Depending on model)
If you do not press any button when Automatic Standby function is on, the TV automatically switches
to the standby mode.
■■ Image shown may differ from your TV.
TIME
Move
TIME
OK
Move
Time
: Off
● Off
Time
: Off
● On
Time
: Off
● On
Time
: Off
: Off
● Sleep
: Off
● Alarm
● Alarm
: Off
: Off
● Automatic Standby : 4 hours
►
● Automatic Standby : 4 hours
Timer
Off
►
Timer
►
● Off
● Sleep
OK
● Clock
● Clock
►
4 hours
Off
6 hours
8 hours
Close
1
MENU
2
3
or
Home
Select TIME.
• This function does not work on Demo mode
or while software update.
Select Automatic Standby.
Select Off, 4 hours, 6 hours or
8 hours.
TIME SETTING
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
112
PARENTAL CONTROL / RATINGS
SET PASSWORD & LOCK SYSTEM
Enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset.
When France is selected for Country, password is not ‘0’, ‘0’, ‘0’, ‘0’ but ‘1’,’2’,’3’,’4’.
When France is selected for Country, password cannot be set as ‘0’, ‘0’, ‘0’, ‘0’.
If a channel is locked, enter the password to unlock it temporarily.
LOCK
● Set
● Parental
2
3
4
or
Programme
Guidance: Blocking Off
Block
Select LOCK.
Home
: :Off
Off
● Block
● Parental
● Input
● Key
OK
Off
Off
● Lock System
: Off
Move
Password
Lock
Programme
On
Guidance: Blocking Off
Block
: Off
• If you forget your password, press ‘0’, ‘3’,
‘2’, ‘5’ on the remote control handset.
Select Lock System.
Select On.
Set the password.
Input a 4-digit password.
Be sure to remember this number!
Re-enter new password for confirm.
PARENTAL CONTROL /
RATINGS
5
● Input
Lock
►
● Block
►
MENU
LOCK
►
: :Off
Off
● Key
OK
● Set
● Lock System
1
Move
Password
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
113
PARENTAL CONTROL / RATINGS
BLOCK PROGRAMME
Blocks any programme that you do not want to watch or that you do not want your children to watch.
It is available to use this function in Lock System ”On”.
Enter a password to watch a blocked programme.
Block Programme
Page 1/2
TV
LOCK
● Set
Move
Password
● Lock
System
: On
● Block
● Parental
● Input
● Key
OK
Lock
▲
Programme
▼
Guidance: Blocking Off
Block
: Off
1 YLE TV1 (D)
2 YLE TV2 (D)
3 YLE FST (D)
4 YLE24 (D)
5 YLE Teema (D)
6 TV4 Stockholm (D)
7 Kanal Lokal (D)
8 CNN (D)
9 TV4 (D)
10 TV4 Plus (D)
11 TV400 (D)
12 TV4 Film (D)
13 TV4 Fakta (D)
14 MediaCorp HD5 (D)
15 SNY_SSU (R)
16 Demo (R)
17 TVE 1 (R)
18 TVE 2 (D)
19 24H TVE (D)
20 CLAN/50 TVE (D)
21 LA7 (R)
▼
Pr. Change
Navigation
P
Page Change
Previous
Block/Unblock
1
or
MENU
2
3
PARENTAL CONTROL /
RATINGS
4
5
Home
Select LOCK.
Select Lock System.
Select Block Programme.
Enter the Block Programme.
YELLOW
Select a programme to be locked.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
114
PARENTAL CONTROL (IN DIGITAL MODE ONLY)
This function operates according to information from the broadcasting station. Therefore if the signal
has incorrect information, this function does not operate.
A password is required to gain access to this menu.
This set is programmed to remember which option it was last set to even if you switch the set off.
Prevents children from watching certain adult’s TV programmes, according to the ratings limit set.
Enter a password to watch a blocked programme.
Rating differs by country.
LOCK
● Set
Move
● Lock
System
● Set
: On
● Block
●● Parental
Parental Guidance
Guidance:: Blocking
Blocking Off
Off
● Input
Lock
Programme
▲
▼
Block
: Off
Move
System
: On
OK
Blocking Off : Permits all
programmes
▲
Password
● Lock
● Key
LOCK
OK
Password
Programme 12 and above
13 and above
● Block
●● Parental
Parental Guidance
Guidance:: Blocking
Blocking Off
Off
● Input
● Key
Lock
: Off
Block
14 and above
12 and above
▲
▼
2
3
15 and above
16 and above
17 and above
17 and above
18 and above
18 and above
Blocking Off
(Only France)
Select LOCK.
Home
Select Lock System.
Select Parental Guidance.
Make appropriate adjustments.
PARENTAL CONTROL /
RATINGS
4
or
14 and above
16 and above
(Except for France)
MENU
13 and above
15 and above
1
Programmes for 18 and above
will be blocked
▲
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
115
PARENTAL CONTROL / RATINGS
EXTERNAL INPUT BLOCKING
Enables you to block an input.
It is available to use this function in Lock System ”On”.
■■ Image shown may differ from your TV.
LOCK
● Set
Move
● Lock
System
● Set
: On
● Block
● Parental
● Input
Lock
Programme
Guidance: Blocking Off
▲
Block
▼
: Off
Move
System
: On
● Block
● Parental
● Key
OK
Password
● Lock
● Key
LOCK
OK
Password
Lock
Programme
● AV
Off
◄
Guidance
: Blocking Off
● Component
● Input Block
● RGB
: Off
● HDMI1
▲
▼
● HDMI2
►
Off
Off
Off
Off
Close
1
MENU
2
3
4
PARENTAL CONTROL /
RATINGS
5
or
Select LOCK.
Home
Select Lock System.
Select Input Block.
Select input source.
Select On or Off.
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
116
KEY LOCK
This feature can be used to prevent unauthorized viewing by locking out the front panel controls, so
that it can only be used with the remote control.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
LOCK
Move
● Lock
System
2
3
: Off
● Lock
● Block
● Parental
● Input
or
Programme
Guidance: Blocking Off
Block
: Off: Off
Select LOCK.
Home
Select Key Lock.
Select On or Off.
Move
OK
Password
System
: Off
● Block
● Parental
● Input
● Key Lock
Programme
Guidance: Blocking Off
Block
Off
: :Off
Off
Off
►
MENU
● Set
● Key
Lock
● Key
Lock
1
LOCK
OK
Password
►
● Set
On
• In Key Lock ‘On’, if the TV is turned off, press the
/ I, INPUT, P
button on the TV or POWER
or NUMBER buttons on the remote
INPUT, P
control then the set will be turned on.
• With the Key Lock On, the display ‘
Key
Lock On ’ appears on the screen if any button on
the front panel is pressed while viewing the TV.
• When another OSD is displayed, ‘
Key Lock
On ’ will not operate.
PARENTAL CONTROL /
RATINGS
• Press the MENU or Home/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
117
This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives up-to-theminute information on news, weather, television programmes, share prices and
many other topics.
(Image shown may
differ from your TV.)
ENERGY
AV MODE
TV/
RAD
SAVING
1.,;@ 2 abc 3 def
4 ghi 5 jkl 6 mno
7pqrs 8 tuv 9 wxyz
LIST
The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT
systems. SIMPLE (standard teletext) consists of a number of pages which are
selected by directly entering the corresponding page number. TOP and
FASTEXT are more modern methods allowing quick and easy selection of
teletext information.
INPUT
0
[
TELETEXT
TELETEXT
Q.VIEW
MARK
FAV
CHAR/NUM
RATIO
P
P
A
G
E
DELETE
MUTE
GUIDE POTAL INFO
OK
SWITCH ON/OFF
MENU
Press the TEXT button to switch to teletext. The initial page or last page
viewed appears on the screen.
Two page numbers, TV station name, date and time are displayed on the
screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The previous mode reappears.
Q.MENU
BACK EXIT
AD
ALARM
SIMPLE TEXT
■■ Page selection
Enter
1
the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the
correct page number.
2 The P
button can be used to select the preceding or following page.
TELETEXT
118
TOP TEXT
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow
field denotes the next group and the blue field indicates the next block.
■■ Block / group / page selection
1 With the blue button you can progress from block to block.
2 Use the yellow button to proceed to the next group with automatic overflow to the next block.
3 With the green button you can proceed to the next existing page with automatic overflow to the next
group.
Alternatively the P button can be used.
4 The red button returns to the previous selection. Alternatively the P
button can be used.
■■ Direct page selection
As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using
the NUMBER buttons in TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing the
corresponding coloured button.
■■Page selection
1
2
3
TELETEXT
4
Press the T.OPT button and then use
button to select
menu. Display the index page.
You can select the pages which are colour coded along the bottom line with corresponding
coloured buttons.
AS with SIMPLE teletext mode, you can select a page by entering its three digit page number with
the NUMBER buttons in FASTEXT mode.
The P
button can be used to select the preceding or following page.
119
TELETEXT
SPECIAL TELETEXT FUNCTIONS
■■ Press the T. OPT button and then use
button to select the Text Option menu.
■■ In UK(In digital mode), T. OPT button does not work.
Text Option
■■Index
Select the each index page.
Index
Time
Hold
Reveal
■■Time
Update
Close
When viewing a TV programme, select this menu to display the time at the top right
hand corner of the screen.
In the teletext mode, press this button to select a sub page number. The sub page number is displayed at
the bottom of the screen. To hold or change the sub page, press the RED/GREEN,< > or NUMBER buttons.
■■ Hold
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages.
The number of sub pages and the sub page displayed is, usually, shown on the screen below the
time. When this menu is selected the stop symbol is displayed at the top left-hand corner of the
screen and the automatic page change is inactive.
■■Reveal
Select this menu to display concealed information, such as solutions to riddles or puzzles.
■■Update
Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at
the top left hand corner of the screen. When the updated page is available then display will change to
the page number. Select this menu again to view the updated teletext page.
TELETEXT
120
DIGITAL TELETEXT
*This function works in UK, Ireland only.
The TV gives you access to digital teletext which is greatly improved in various aspects such as text,
graphics etc.
This digital teletext can access special digital teletext services and specific services which broadcast
digital teletext.
TELETEXT WITHIN DIGITAL SERVICE
1
Press the numeric or P
button to select a
digital service which broadcasts digital teletext.
2
Follow the indications on digital teletext and
move onto the next step by pressing TEXT,
OK,
, RED, GREEN, YELLOW, BLUE
or NUMBER buttons and etc..
3
To change digital teletext service, select a different service by the numeric or P
button.
TELETEXT IN DIGITAL SERVICE
Press the numeric or P
button to select a
certain service which broadcasts digital teletext.
2
Press the TEXT or coloured button to switch on
teletext.
3
Follow the indications on digital teletext and move
onto the next step by pressing OK,
, RED,
GREEN, YELLOW, BLUE or NUMBER buttons and
so on.
4
Press the TEXT or colour button to switch off
digital teletext and return to TV viewing.
Some services may allow you to access text services by pressing the RED button.
DIGITAL TELETEXT
1
121
APPENDIX
APPENDIX
TROUBLESHOOTING
The TV does not operate properly.
The remote control
does not work
■■ Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control
directly at the TV.
■■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■■ Install new batteries.
■■ Is the sleep timer set?
Power is suddenly
■■ Check the power control settings. Has the Power supply been interrupted.
turned off
■■ If the TV is switched on and there is no input signal, it will switch off automatically after 15 minutes.
The video function does not work.
■■ Check whether the TV is switched on.
■■ Try another channel. The problem may be with the broadcast.
No picture & No sound ■■ Is the power cord inserted correctly into the mains?
■■ Check your antenna direction and/or location.
■■ Test the mains outlet by plugging another TV into the same outlet.
Picture appears slowly ■■ This is normal, the image is muted during the TV startup process. Please contact
your service centre, if the picture has not appeared after five minutes.
after switching on
■■ Adjust Colour in menu option.
No or poor colour
or poor picture
■■ Allow a sufficient distance between the TV and the VCR.
■■ Try another channel. The problem may be with the broadcast.
■■ Are the video cables installed properly?
■■ Activate any function to restore the brightness of the picture.
Horizontal/vertical bars
or picture shaking
Poor reception on
some channels
Lines or streaks
in pictures
No picture
APPENDIX
122
when connecting
HDMI
■■ Check for local interference such as an electrical appliance or power tool.
■■ Station or cable channel experiencing problems, tune to another station.
■■ Station signal is weak, reposition the antenna to receive weaker stations.
■■ Check for sources of possible interference.
■■ Check antenna (Change the position of the antenna).
■■ Check that your HDMI cable is High Speed HDMI Cable.
If the HDMI cables are not High Speed HDMI Cable, flickering or no screen display
can result. Please use the High Speed HDMI Cable.
The audio function does not work.
Picture OK & No
sound
No output from one
of the speakers
Unusual sound from
inside the TV
No sound when connecting HDMI or USB
■■ Press the
+ or - button.
■■ Sound muted? Press MUTE button.
■■ Try another channel. The problem may be with the broadcast.
■■ Are the audio cables installed properly?
■■ Adjust Balance in menu option.
■■ A change in ambient humidity or temperature may result in an unusual noise
when the TV is switched on or off and does not indicate a fault with the TV.
■■ Check HDMI cable is High Speed HDMI Cable.
■■ Check USB cable over version 2.0.
*This feature is not available for all models.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of
range
(Invalid format)
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
Screen colour is
unstable or single
colour
■■ Adjust resolution, horizontal frequency, or vertical frequency.
■■ Check the input source.
■■ Use Auto configure or adjust clock, phase, or H/V position. (Option)
■■ Check the signal cable.
■■ Reinstall the PC video card.
APPENDIX
123
APPENDIX
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV.
Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1
A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is
almost dry, and then use it to wipe the screen.
2
Ensure there is no excess water on the screen. Allow any water or dampness to evaporate
before switching on.
Cleaning the Cabinet
■■ To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■■ Do not to use a wet cloth.
Extended Absence
CAUTION
►►If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to
protect against possible damage from lightning or power surges.
APPENDIX
124
PRODUCT SPECIFICATIONS
MODELS
Dimensions
(Width x Height x
Depth)
Weight
797.0 mm x 555.0 mm x 207.0 mm
without stand
797.0 mm x 495.0 mm x 97.1 mm
with stand
without stand
10.2 kg
9.4 kg
AC 100-240 V~ 50 / 60 Hz
150 W
Power Consumption
MODELS
(Width x Height x
Depth)
Weight
37LD650H-ZA
916.0 mm x 625.0 mm x 261.0 mm
without stand
916.0 mm x 560.0 mm x 88.9 mm
with stand
without stand
13.6 kg
12.0 kg
AC 100-240 V~ 50 / 60 Hz
170 W
Power Consumption
CI Module Size
100.0 mm x 55.0 mm x 5.0 mm
(Width x Height x Depth)
Operating Temperature
Supported movie files
37LD6***
with stand
Power requirement
Environment condition
32LD650H-ZA
with stand
Power requirement
Dimensions
32LD6***
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60° C
Storage Humidity
Less than 85 %
Refer to p. 42 to 43
■■ The specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
125
APPENDIX
MODELS
Dimensions
(Width x Height x
Depth)
Weight
1024.0 mm x 685.0 mm x 261.0 mm
without stand
1024.0 mm x 621.0 mm x 87.1 mm
with stand
without stand
16.7 kg
15.1 kg
AC 100-240 V~ 50 / 60 Hz
210 W
Power Consumption
MODELS
(Width x Height x
Depth)
Weight
47LD650H-ZA
1137.0 mm x 758.0 mm x 270.0 mm
without stand
1137.0 mm x 685.0 mm x 76.8 mm
with stand
without stand
20.3 kg
18.3 kg
AC 100-240 V~ 50 / 60 Hz
250 W
Power Consumption
CI Module Size
100.0 mm x 55.0 mm x 5.0 mm
(Width x Height x Depth)
Operating Temperature
Supported movie files
47LD6***
with stand
Power requirement
Environment condition
42LD650H-ZA
with stand
Power requirement
Dimensions
42LD6***
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60° C
Storage Humidity
Less than 85 %
Refer to p. 42 to 43
■■ The specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
126
MODELS
Dimensions
(Width x Height x
Depth)
Weight
764.0 mm x 545.0 mm x 240.0 mm
without stand
764.0 mm x 484.0 mm x 35.4 mm
with stand
without stand
11.4 kg
9.6 kg
AC 100-240 V~ 50 / 60 Hz
80 W
Power Consumption
MODELS
(Width x Height x
Depth)
Weight
37LV375H-ZA
888.0 mm x 614.0 mm x 240.0 mm
without stand
888.0 mm x 553.0 mm x 35.4 mm
with stand
without stand
13.5 kg
11.7 kg
AC 100-240 V~ 50 / 60 Hz
100 W
Power Consumption
CI Module Size
100.0 mm x 55.0 mm x 5.0 mm
(Width x Height x Depth)
Operating Temperature
Supported movie files
37LV3***
with stand
Power requirement
Environment condition
32LV375H-ZA
with stand
Power requirement
Dimensions
32LV3***
Operating Humidity
0 °C to 40 °C
Less than 80 %
Storage Temperature
-20 °C to 60° C
Storage Humidity
Less than 85 %
Refer to p. 42 to 43
■■ The specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
127
APPENDIX
42LV3***
MODELS
Dimensions
(Width x Height x
Depth)
Weight
42LV375H-ZA
with stand
998.0 mm x 684.0 mm x 256.0 mm
without stand
998.0 mm x 615.0 mm x 30.4 mm
with stand
without stand
15.5 kg
13.3 kg
Power requirement
AC 100-240 V~ 50 / 60 Hz
120 W
Power Consumption
47LV3***
MODELS
Dimensions
(Width x Height x
Depth)
Weight
47LV375H-ZA
with stand
1108.0 mm x 746.0 mm x 256.0 mm
without stand
1108.0 mm x 677.0 mm x 30.4 mm
with stand
without stand
20.9 kg
18.7 kg
Power requirement
AC 100-240 V~ 50 / 60 Hz
140 W
Power Consumption
CI Module Size
100.0 mm x 55.0 mm x 5.0 mm
(Width x Height x Depth)
Operating Temperature
Environment condition
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60° C
Storage Humidity
Less than 85 %
Supported movie files
Television System
Programme Coverage
Refer to p. 42 to 43
Digital TV
Analogue TV
DVB-T
PAL/SECAM B/G/D/K, PAL I/II,
DVB-C
VHF, UHF
Maximum number of storable programmes
APPENDIX
128
External Antenna Impedance
SECAM L/L’
VHF: E2 to E12, UHF: E21 to E69,
CATV: S1 to S20, HYPER: S21 to S47
500
75 Ω
■■ The specifications shown above may be changed without prior notice for quality improvement.
75 Ω
IR CODES
*This feature is not available for all models.
Code (Hexa)
Function
Note
95
Energy Saving
R/C BUTTON
08
POWER
R/C BUTTON(POWER ON/OFF)
0B
INPUT
R/C BUTTON
79
RATIO
R/C BUTTON
F0
TV/RAD
R/C BUTTON
45
Q.MENU
R/C BUTTON
43
MENU or Home
R/C BUTTON
AB
GUIDE
R/C BUTTON
40
Up (
R/C BUTTON
41
Down (
07
Left (
06
Right (
44
OK( )
R/C BUTTON
)
)
R/C BUTTON
R/C BUTTON
)
)
R/C BUTTON
28
BACK
R/C BUTTON
5B
EXIT
R/C BUTTON
AA
INFO i
R/C BUTTON
30
AV MODE
R/C BUTTON
02
+
R/C BUTTON
03
-
R/C BUTTON
1E
MARK (CHAR/NUM)
R/C BUTTON
09
MUTE (DELETE)
R/C BUTTON
00
P
R/C BUTTON
01
P
R/C BUTTON
Number Key 0 to 9
R/C BUTTON
10 to 19
53
LIST
R/C BUTTON
1A
Q.VIEW
R/C BUTTON
72
RED Key
R/C BUTTON
71
GREEN Key
R/C BUTTON
63
YELLOW Key
R/C BUTTON
61
BLUE Key
R/C BUTTON
20
TEXT
R/C BUTTON
21
T.OPT(T.Option)
R/C BUTTON
SUBTITLE
R/C BUTTON
SIMPLINK
R/C BUTTON
91
AD
R/C BUTTON
B1
▀
R/C BUTTON
B0
►
R/C BUTTON
BA
ll
R/C BUTTON
8F
◄◄
R/C BUTTON
8E
►►
R/C BUTTON
0C
PORTAL
R/C BUTTON
E8
ALARM
R/C BUTTON
APPENDIX
39
7E
129
APPENDIX
EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup
HDMI/DVI IN
2
RJP
INTERFACE
LAN
(RGB)
1
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an
A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied
with the product.
VOLUME CONTROL
STEREO (8
)
SPEAKER
OUT
Type of Connector; D-Sub 9-Pin Male
No.
1
2
3
4
5
6
7
8
9
APPENDIX
130
Pin Name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
+5V Power out 1A
CTS (Clear to send)
+12V Power out 1A
1
5
6
9
Set ID
Use this function to specify a set ID number.
Refer to ‘Real Data Mapping’. ► p.135
● Demo
Mode
Mode
Move
● Language(Language)
● Country
: UK
● Disability Assistance
● Disability Assistance
● Power
● Power
Indicator
or
::11
Home
: UK
Indicator
● Factory
►
Reset
◄
Reset
● Set ID
OK
: On
::11
1
►
3
● Demo
►
2
: On
● Country
● Set ID
MENU
OPTION
OK
● Language(Language)
● Factory
1
Move
►
►
OPTION
Close
Select OPTION.
Select Set ID.
Adjust Set ID to choose the desired TV ID number.
The adjustment range of SET ID is 1 to 99.
APPENDIX
• Press the BACK button to move to the previous menu screen.
131
APPENDIX
Communication Parameters
■■ Baud rate : 9600 bps (UART)
■■ Data length : 8 bits
■■ Parity : None
■■ Stop bit : 1 bit
■■ Communication code : ASCII code
■■ Use a crossed (reverse) cable.
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
Command Reference List
COMMAND COMMAND
1
2
APPENDIX
132
DATA
(Hexadecimal)
01. Power
k
a
00 to 01
02. Aspect Ratio
k
c
Refer to p. 133
03. Screen Mute
k
d
Refer to p. 133
04. Volume Mute
k
e
00 to 01
05. Volume Control
k
f
00 to 64
06. Contrast
k
g
00 to 64
07. Brightness
k
h
00 to 64
08. Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 64
11. OSD Select
k
l
00 to 01
12. Remote control lock mode
k
m
00 to 01
13. Treble
k
r
00 to 64
14. Bass
k
s
00 to 64
15. Balance
k
t
00 to 64
16. Colour Temperature
x
u
00 to 64
17. Energy Saving
j
q
00 to 05
18. Auto Configuration
j
u
01
19. Tune Command
m
a
Refer to p. 135
20. Programme Add/Skip
m
b
00 to 01
21. Key
m
c
Key Code
22. Control Back Light
m
g
00 to 64
23. Input select (Main)
x
b
Refer to p. 136
* [Command 1] : First command to control the TV.
(j, k, m or x)
* [Command 2] : Second command to control the TV.
: You can adjust the set ID to choose
* [Set ID]
desired monitor ID number in option
menu. Adjustment range is 1 to 99.
When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99)
on menu and as Hexa decimal (0x0 to
0x63) on transmission/receiving protocol.
[DATA]
:
To
transmit command data.
*
Transmit ‘FF’ data to read status of command.
: Carriage Return
* [Cr] ASCII code ‘0x0D’
: ASCII code ‘space (0x20)’
* [ ]
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based
on this format when receiving normal data. At this
time, if the data is data read mode, it indicates
present status data. If the data is data write mode,
it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based
on this format when receiving abnormal data from
* Note : During USB operations such as DivX or EMF, all
commands except Power(ka) and Key(mc) are not exe- non-viable functions or communication errors.
cuted and treated as NG.
Data00: Illegal Code
01. Power (Command: k a)
►► To control Power On/Off of the set.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data00 : Power Off
Ack
01 : Power On
[a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack
[e][ ][Set ID][ ][OK/NG][Data][x]
[k][a][ ][Set ID][ ][FF][Cr]
05. Volume Control (Command: k f)
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data
based on this format, Acknowledgement data feed
back presents status about each function.
* OK Ack., Error Ack. and other message may display on the screen when TV is power On.
02. Aspect Ratio (Command: k c) (Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen (16:9)
04 : Zoom
06 : Original
Ack
04. Volume Mute (Command: k e)
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
►► To adjust volume.
You can also adjust volume with the VOLUME buttons on remote control.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
[f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
[c][ ][Set ID][ ][OK/NG][Data][x]
[g][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz /
60 Hz, 1080p 24 Hz / 30 Hz / 50 Hz / 60 Hz),
Component( 720p, 1080i, 1080p 50 Hz / 60 Hz)
mode, Just Scan is available.
* Full Wide is supported only for Digital, Analogue,
AV.
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Transmission
Ack
[d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
[h][ ][Set ID][ ][OK/NG][Data][x]
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
[i][ ][Set ID][ ][OK/NG][Data][x]
APPENDIX
[k][d][ ][Set ID][ ][Data][Cr]
Data00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
[k][h][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
133
APPENDIX
09. Tint (Command: k j)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
13. Treble (Command: k r)
Transmission
►► To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
[k][r][ ][Set ID][ ][Data][Cr]
DataRed : 00 to Green : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
[j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
[k][ ][Set ID][ ][OK/NG][Data][x]
Ack
[r][ ][Set ID][ ][OK/NG][Data][x]
14. Bass (Command: k s)
►► To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
[s][ ][Set ID][ ][OK/NG][Data][x]
15. Balance (Command: k t)
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling remotely.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
Ack
01 : OSD on
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
[t][ ][Set ID][ ][OK/NG][Data][x]
[l][ ][Set ID][ ][OK/NG][Data][x]
16. Colour Temperature (Command: x u)
12. Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and
remote control.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data00 : Lock off
Ack
APPENDIX
134
01 : Lock on
[m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is on/off, external control lock is
released.
* In the standby mode, if key lock is on, TV will not
turn on by power on key of IR & Local Key.
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Transmission
[x][u][ ][Set ID][ ][Data][Cr]
DataMin : 00 to Max : 64
* Refer to ‘Real data mapping’. Refer to p. 135
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
17. Energy Saving (Command: j q)
19. Tune Command (Command: m a)
►► To reduce the power consumption of the TV. You can
also adjust Energy Saving in PICTURE menu.
Transmission
►► Select channel to following physical number.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data00 :High channel data
Data01 :Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 :0x00 : Analogue Main
0x10 : DTV Main
0x20 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
(Except For Sweden, Finland, Norway, Denmark,
Ireland)
Digital - Min: 00 to Max: 270F (0 to 9999)
(Only Sweden, Finland, Norway, Denmark, Ireland)
Power Saving
Function
7
6
5
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Level
Description
3
2
1
0
Low Power
0
0
0
0
Off
0
Low Power
0
0
0
1
Minimum
0
Low Power
0
0
1
0
Medium
0
0
Low Power
0
0
1
1
Maximum
0
0
Low Power
0
1
0
0
Auto
0
0
Low Power
0
1
0
1
Screen Off
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
DataMin: 00 to Max: 7DH
Ack
[q][ ][Set ID][ ][OK/NG][Data][x]
18. Auto Configure(Command: j u)
►► To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data01: To set
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
20. Programme Add/Skip(Command: m b)
►► To set skip status for the current Programme.
Transmission
[m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping
00 : Step 0
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E : Step 110
Step 115
Step 116
CF : Step 199
FE : Step 254
FF : Step 255
APPENDIX
73 :
74 :
135
APPENDIX
21. Key(Command: m c)
►► To send IR remote key code.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
DataKey code - Refer to page 129.
Ack
[c][ ][Set ID][ ][OK/NG][Data][x]
23. Input select (Command: x b)
(Main Picture Input)
►► To select input source for main picture.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
DataStructure
MSB
0
LSB
0
0
0
External Input
22. Control Back Light (Command: m g)
►► To Control the back light.
Transmission
[m][g][ ][Set ID][ ][Data][Cr]
Data: data Min: 00 to Max: 64
Ack
[g][ ][Set ID][ ][OK/NG][Data][x]
0
0
0
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
1
0
0
0
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
APPENDIX
136
0
OPEN SOURCE SOFTWARE NOTICE
The following GPL executables and LGPL, MPL libraries used in this product are subject to the
GPL2.0/LGPL2.1/MPL1.1 License Agreements:
GPL EXECUTABLES:
Linux kernel, busybox, e2fsprogs, jfsutils, lzo, mtd-utils,udhcpc
LGPL LIBRARIES:
directFB, glib, iconv, uClibc
MPL LIBRARIES:
Cairo, Nanox
LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of
performing such distribution, such as the cost of media, shipping and handling upon e-mail request
to LG Electronics : opensource@lge.com
This offer is valid for a period of three (3) years from the date of the distribution of this product by
LG Electronics.
You can obtain a copy of the GPL, LGPL, MPL licenses on the CD-ROM provided with this product.
Also you can obtain the translation of GPL, LGPL licenses from http://www.gnu.org/licenses/old-licenses/gpl-2.0-translations.html, http://www.gnu.org/licenses/old-licenses/lgpl-2.1-translations.html.
This product includes ReportGUI component which is licensed under the terms of the Apache
License, Version 2.0.
You can obtain a copy of the Apache license from http://www.apache.org/licenses/LICENSE-2.0.html.
This product includes other open source software.
■■ chromium: copyright © 2008, The Chromium Authors
■■ expat:
• copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper
• copyright © 2001-2007 Expat maintainers.
■■ freetype: copyright © 2003 The FreeType Project (www.freetype.org).
■■ ICU: copyright © 1995-2001 International Business Machines Corporation and others.
■■ libcurl: copyright © 1996 - 2008, Daniel Stenberg.
■■ libjpeg: This software is based in part on the work of the Independent JPEG Group copyright ©
1991 – 1998, Thomas G. Lane.
■■ libmng: copyright © 2000-2007 Gerard Juyn, Glenn Randers-Pehrson
■■ libpng: copyright © 1998-2008 Glenn Randers-Pehrson
■■ mt19937: copyright © 1997 - 2002, Makoto Matsumoto and Takuji Nishimura
■■ netBSD : copyright © 1998 The NetBSD Foundation, Inc.
■■ openSSL:
• cryptographic software written by Eric Young.
• software written by Tim Hudson.
• software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org)
APPENDIX
137
APPENDIX
■■ pixman:
• copyright © 1987, 1988, 1989, 1998 The Open Group
• copyright © 1987, 1988, 1989 Digital Equipment Corporation
• copyright © 1999, 2004, 2008 Keith Packard
• copyright © 2000 SuSE, Inc.
• copyright © 2000 Keith Packard, member of The XFree86 Project, Inc.
• copyright © 2004, 2005, 2007, 2008 Red Hat, Inc.
• copyright © 2004 Nicholas Miell
• copyright © 2005 Lars Knoll & Zack Rusin, Trolltech
• copyright © 2005 Trolltech AS
• copyright © 2007 Luca Barbato
• copyright © 2008 Aaron Plattner, NVIDIA Corporation
• copyright © 2008 Rodrigo Kumpera
• copyright © 2008 André Tupinambá
• copyright © 2008 Mozilla Corporation
• copyright © 2008 Frederic Plourde
■■ portmap: copyright © 1983,1991 The Regents of the University of California.
■■ tinyxml: copyright © 2000-2006 Lee Thomason
■■ xyssl:
• copyright © 2006-2008 Christophe Devine
• copyright © 2009 Paul Bakker
■■ zlib: copyright © 1995-2005 Jean-loup Gailly and Mark Adler
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and
associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or
sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
OTHER DEALINGS IN THE SOFTWARE.
APPENDIX
138
OPEN SOURCE LICENSE
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public License is intended to guarantee your freedom to share and change free
software--to make sure the software is free for all its users. This General Public License applies to most of the Free
Software Foundation's software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to
make sure that you have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software,
or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show
them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so that any problems introduced by others will not
reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors
of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we
have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
The act of running the Program is not restricted, and the output from the Program
is covered only if its contents constitute a work based on the Program (independent of having been made by running
the Program). Whether that is true depends on what the Program does.
APPENDIX
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it
may be distributed under the terms of this General Public License. The "Program", below, refers to any such program
or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that
is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is
addressed as "you".
139
APPENDIX
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of
any warranty; and give any other recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program,
and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all
of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any
change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the
Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this
License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may
redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception:
if the Program itself is interactive but does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on
the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable
form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under
the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a complete machine-readable copy of the corresponding
source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
APPENDIX
140
The source code for a work means the preferred form of the work for making modifications to it. For an executable
work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary
form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place counts as distribution of the source code, even though
third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.
Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate
your rights under this License. However, parties who have received copies, or rights, from you under this License will
not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not
accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a
license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You
may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible
for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you
may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the
Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it
and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution
system, which is implemented by public license practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to
time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems
or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which
applies to it and "any later version", you have the option of following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If the Program does not specify a version number of
this License, you may choose any version ever published by the Free Software Foundation.
APPENDIX
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different,
write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to
the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals
of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software
generally.
141
APPENDIX
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve
this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to
where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public
License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later
version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General
Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the
Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO
WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain
conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
Of course, the commands you use may be called something other than `show w' and `show c'; they could even be
mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer"
for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker.
APPENDIX
142
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a
subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is
what you want to do, use the GNU Lesser General Public License instead of this License.
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the
software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically
libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest
you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in
any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you
wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of
it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the
library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the
rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code
with the library, you must provide complete object files to the recipients, so that they can relink them with the library
after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the recipients should know that what they have is not the original
version, so that the original author's reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a
company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.
Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom
of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is
legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore
permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits
more lax criteria for linking other code with the library.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the
ordinary General Public License. It also provides other free software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain special circumstances.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use
a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
APPENDIX
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library,
so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more
frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to
gain by limiting the free library to free software only, so we use the Lesser General Public License.
143
APPENDIX
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a
program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from
the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the
copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public
License (also called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been distributed under these terms. A
"work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work
containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into
another language. (Hereinafter, translation is included without limitation in the term "modification".)
"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete
source code means all the source code for all modules it contains, plus any associated interface definition files, plus
the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
The act of running a program using the Library is not restricted, and output from such a program is covered only if its
contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether
that is true depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection
in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library,
and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all
of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of
any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this
License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program
that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good
faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates,
and performs whatever part of its purpose remains meaningful.
APPENDIX
144
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of
the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function
must be optional: if the application does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Library, and can be reasonably considered independent and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the
Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy
of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU
General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU
General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other
change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License
applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding
machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent
access to copy the source code from the same place satisfies the requirement to distribute the source code, even
though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being
compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of
the Library, and therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library
(because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the
work may be a derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library.
The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and
small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it
is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under
Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of
Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with
the Library itself.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library
to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that
the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its
use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one of these things:
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at
run time a copy of the library already present on the user's computer system, rather than copying library functions
into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as
long as the modified version is interface-compatible with the version that the work was made with.
APPENDIX
a) Accompany the work with the complete corresponding machine-readable source code for the Library including
whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object
code and/or source code, so that the user can modify the Library and then relink to produce a modified executable
containing the modified Library. (It is understood that the user who changes the contents of definitions files in the
Library will not necessarily be able to recompile the application to use the modified definitions.)
145
APPENDIX
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials
specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to
copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the "work that uses the Library" must include any data and utility programs
needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need
not include anything that is normally distributed (in either source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies
the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in
an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with
other library facilities not covered by this License, and distribute such a combined library, provided that the separate
distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that
you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and
explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this
License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept
this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your
acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or
works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a
license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.
You are not responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you
may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the
Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and
this License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
APPENDIX
146
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution
system which is implemented by public license practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from
time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which
applies to it and "any later version", you have the option of following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If the Library does not specify a license version number,
you may choose any version ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible
with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation,
write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two
goals of preserving the free status of all derivatives of our free software and of promoting the sharing
and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO
THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it
free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or,
alternatively, under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file
to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer
to where the full notice is found.
<one line to give the library's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General
Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any
later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public
License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the
Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by
James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
APPENDIX
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer"
for the library, if necessary. Here is a sample; alter the names:
147
APPENDIX
MOZILLA PUBLIC LICENSE
Version 1.1
--------------1. Definitions.
1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party.
1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications.
1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor,
and the Modifications made by that particular Contributor.
1.3. "Covered Code" means the Original Code or Modifications or the combination of the Original Code and
Modifications, in each case including portions thereof.
1.4. "Electronic Distribution Mechanism" means a mechanism generally accepted in the software development community for the electronic transfer of data.
1.5. "Executable" means Covered Code in any form other than Source Code.
1.6. "Initial Developer" means the individual or entity identified as the Initial Developer in the Source Code notice
required by Exhibit A.
1.7. "Larger Work" means a work which combines Covered Code or portions thereof with code not governed by the
terms of this License.
1.8. "License" means this document.
1.8.1. "Licensable" means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein.
1.9. "Modifications" means any addition to or deletion from the substance or structure of either the Original Code or
any previous Modifications. When Covered Code is released as a series of files, a Modification is:
A. Any addition to or deletion from the contents of a file containing Original Code or previous Modifications.
B. Any new file that contains any part of the Original Code or previous Modifications.
1.10. "Original Code" means Source Code of computer software code which is described in the Source Code notice
required by Exhibit A as Original Code, and which, at the time of its release under this License is not already
Covered Code governed by this License.
1.10.1. "Patent Claims" means any patent claim(s), now owned or hereafter acquired, including without limitation,
method, process, and apparatus claims, in any patent Licensable by grantor.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all
modules it contains, plus any associated interface definition files, scripts used to control compilation and installation
of an Executable, or source code differential comparisons against either the Original Code or another well known,
available Covered Code of the Contributor's choice. The Source Code can be in a compressed or archival form,
provided the appropriate decompression or de-archiving software is widely available for no charge.
1.12. "You" (or "Your") means an individual or a legal entity exercising rights under, and complying with all of the
terms of, this License or a future version of this License issued under Section 6.1.
For legal entities, "You" includes any entity which controls, is controlled by, or is under common control with You.
For purposes of this definition, "control" means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
APPENDIX
148
2. Source Code License.
2.1. The Initial Developer Grant.
The Initial Developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims:
(a) under intellectual property rights (other than patent or trademark) Licensable by Initial Developer to use,
reproduce, modify, display, perform, sublicense and distribute the Original Code (or portions thereof) with or
without Modifications, and/or as part of a Larger Work; and
(b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use,
practice, sell, and offer for sale, and/or otherwise dispose of the Original Code (or portions thereof).
(c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes
Original Code under the terms of this License.
(d) Notwithstanding Section 2.1(b) above, no patent license is granted: 1) for code that You delete from the
Original Code; 2) separate from the Original Code; or 3) for infringements caused by: i) the modification of the
Original Code or ii) the combination of the Original Code with other software or devices.
2.2. Contributor Grant.
Subject to third party intellectual property claims, each Contributor hereby grants You a world-wide, royalty-free,
non-exclusive license
(a) under intellectual property rights (other than patent or trademark) Licensable by Contributor, to use, reproduce, modify, display, perform, sublicense and distribute the Modifications created by such Contributor (or portions thereof) either on an unmodified basis, with other Modifications, as Covered Code and/or as part of a
Larger Work; and
(b) under Patent Claims infringed by the making, using, or selling of Modifications made by that Contributor
either alone and/or in combination with its Contributor Version (or portions of such combination), to make, use,
sell, offer for sale, have made, and/or otherwise dispose of: 1) Modifications made by that Contributor (or portions
thereof); and 2) the combination of Modifications made by that Contributor with its Contributor Version (or portions of such combination).
(c) the licenses granted in Sections 2.2(a) and 2.2(b) are effective on the date Contributor first makes
Commercial Use of the Covered Code.
(d) Notwithstanding Section 2.2(b) above, no patent license is granted: 1) for any code that Contributor has deleted from the Contributor Version; 2) separate from the Contributor Version; 3) for infringements caused by: i)
third party modifications of Contributor Version or ii) the combination of Modifications made by that Contributor
with other software (except as part of the Contributor Version) or other devices; or 4) under Patent Claims
infringed by Covered Code in the absence of Modifications made by that Contributor.
3. Distribution Obligations.
3.1. Application of License.
The Modifications which You create or to which You contribute are governed by the terms of this License, including
without limitation Section 2.2. The Source Code version of Covered Code may be distributed only under the terms of
this License or a future version of this License released under Section 6.1, and You must include a copy of this
License with every copy of the Source Code You distribute. You may not offer or impose any terms on any Source
Code version that alters or restricts the applicable version of this License or the recipients' rights hereunder.
However, You may include an additional document offering the additional rights described in Section 3.5.
3.2. Availability of Source Code.
Any Modification which You create or to which You contribute must be made available in Source Code form under
the terms of this License either on the same media as an Executable version or via an accepted Electronic
Distribution Mechanism to anyone to whom you made an Executable version available; and if made available via
Electronic Distribution Mechanism, must remain available for at least twelve (12) months after the date it initially
became available, or at least six (6) months after a subsequent version of that particular Modification has been
made available to such recipients. You are responsible for ensuring that the Source Code version remains available
even if the
Electronic Distribution Mechanism is maintained by a third party.
3.3. Description of Modifications.
You must cause all Covered Code to which You contribute to contain a file documenting the changes You made to
create that Covered Code and the date of any change. You must include a prominent statement that the Modification
is derived, directly or indirectly, from Original Code provided by the Initial Developer and including the name of the
Initial Developer in (a) the Source Code, and (b) in any notice in an Executable version or related documentation in
which You describe the origin or ownership of the Covered Code.
APPENDIX
3.4. Intellectual Property Matters
(a) Third Party Claims.
If Contributor has knowledge that a license under a third party's intellectual property rights is required to exercise
the rights granted by such Contributor under Sections 2.1 or 2.2, Contributor must include a text file with the
Source Code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient
detail that a recipient will know whom to contact. If Contributor obtains such knowledge after the Modification is
made available as described in Section 3.2, Contributor shall promptly modify the LEGAL file in all copies
Contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or
newsgroups) reasonably calculated to inform those who received the Covered Code that new knowledge has
been obtained.
149
APPENDIX
(b) Contributor APIs.
If Contributor's Modifications include an application programming interface and Contributor has knowledge of
patent licenses which are reasonably necessary to implement that API, Contributor must also include this information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to Section 3.4(a) above, Contributor believes that
Contributor's Modifications are Contributor's original creation(s) and/or Contributor has sufficient rights to grant
the rights conveyed by this License.
3.5. Required Notices.
You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a
particular Source Code file due to its structure, then You must include such notice in a location (such as a relevant
directory) where a user would be likely to look for such a notice. If You created one or more Modification(s)
You may add your name as a Contributor to the notice described in Exhibit A. You must also duplicate this License
in any documentation for the Source Code where You describe recipients' rights or ownership rights relating to
Covered Code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations
to one or more recipients of Covered Code. However, You may do so only on Your own behalf, and not on behalf of
the Initial
Developer or any Contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by You alone, and You hereby agree to indemnify the Initial Developer and every Contributor
for any liability incurred by the Initial Developer or such Contributor as a result of warranty, support, indemnity or liability terms You offer.
3.6. Distribution of Executable Versions.
You may distribute Covered Code in Executable form only if the requirements of Section 3.1-3.5 have been met for
that Covered Code, and if You include a notice stating that the Source Code version of the Covered Code is available under the terms of this License, including a description of how and where You have fulfilled the obligations of
Section 3.2. The notice must be conspicuously included in any notice in an Executable version, related documentation or collateral in which You describe recipients' rights relating to the Covered Code. You may distribute the
Executable version of Covered Code or ownership rights under a license of Your choice, which may contain terms
different from this License, provided that You are in compliance with the terms of this License and that the license
for the Executable version does not attempt to limit or alter the recipient's rights in the Source Code version from
the rights set forth in this
License. If You distribute the Executable version under a different license You must make it absolutely clear that any
terms which differ from this License are offered by You alone, not by the Initial Developer or any Contributor. You
hereby agree to indemnify the Initial Developer and every Contributor for any liability incurred by the Initial
Developer or such Contributor as a result of any such terms You offer.
3.7. Larger Works.
You may create a Larger Work by combining Covered Code with other code not governed by the terms of this
License and distribute the Larger Work as a single product. In such a case, You must make sure the requirements
of this License are fulfilled for the Covered Code.
4. Inability to Comply Due to Statute or Regulation.
If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered
Code due to statute, judicial order, or regulation then You must: (a) comply with the terms of this License to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in
the LEGAL file described in Section 3.4 and must be included with all distributions of the Source Code. Except to
the
extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary
skill to be able to understand it.
5. Application of this License.
This License applies to code to which the Initial Developer has attached the notice in Exhibit A and to related
Covered Code.
6. Versions of the License.
APPENDIX
150
6.1. New Versions.
Netscape Communications Corporation ("Netscape") may publish revised and/or new versions of the License from
time to time. Each version will be given a distinguishing version number.
6.2. Effect of New Versions.
Once Covered Code has been published under a particular version of the License, You may always continue to use
it under the terms of that version. You may also choose to use such Covered Code under the terms of any subsequent version of the License published by Netscape. No one other than Netscape has the right to modify the terms
applicable to Covered Code created under this License.
6.3. Derivative Works.
If You create or use a modified version of this License (which you may only do in order to apply it to code which is
not already Covered Code governed by this License), You must (a) rename Your license so that the phrases
"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in
your license (except to note that your license differs from this License) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public License and Netscape Public License. (Filling
in the name of the Initial Developer, Original Code or Contributor in the notice described in Exhibit A shall not of
themselves be deemed to be modifications of this License.)
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN "AS IS" BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE
COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NONINFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH
YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL
DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR
OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE.
NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1. This License and the rights granted hereunder will terminate automatically if You fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the Covered
Code which are properly granted shall survive any termination of this License. Provisions which, by their nature,
must remain in effect beyond the termination of this License shall survive.
8.2. If You initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against
Initial Developer or a Contributor (the Initial Developer or Contributor against whom You file such action is referred
to as "Participant") alleging that:
(a) such Participant's Contributor Version directly or indirectly infringes any patent, then any and all rights granted
by such Participant to You under Sections 2.1 and/or 2.2 of this License shall, upon 60 days notice from Participant
terminate prospectively, unless if within 60 days after receipt of notice You either: (i) agree in writing to pay
Participant a mutually agreeable reasonable royalty for Your past and future use of Modifications made by such
Participant, or (ii) withdraw Your litigation claim with respect to the Contributor Version against such Participant. If
within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by
the parties or the litigation claim is not withdrawn, the rights granted by Participant to You under Sections 2.1 and/or
2.2 automatically terminate at the expiration of the 60 day notice period specified above.
(b) any software, hardware, or device, other than such Participant's Contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by such Participant under Sections 2.1(b) and 2.2(b) are
revoked effective as of the date You first made, used, sold, distributed, or had made, Modifications made by that
Participant.
8.3. If You assert a patent infringement claim against Participant alleging that such Participant's Contributor Version
directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the
initiation of patent infringement litigation, then the reasonable value of the licenses granted by such Participant
under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license.
8.4. In the event of termination under Sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by You or any distributor hereunder prior to termination shall
survive termination.
9. LIMITATION OF LIABILITY.
APPENDIX
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING
NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER
CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES,
BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF
ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR
LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.
THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY
RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH
LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
151
APPENDIX
10. U.S. GOVERNMENT END USERS.
The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
"commercial computer software" and "commercial computer software documentation," as such terms are used in 48
C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June
1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein.
11. MISCELLANEOUS.
This License represents the complete agreement concerning subject matter hereof. If any provision of this License
is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This
License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise),
excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity
chartered or registered to do business in the United States of America, any litigation relating to this License shall be
subject to the jurisdiction of the Federal Courts of the Northern District of California, with venue lying in Santa Clara
County, California, with the losing party responsible for costs, including without limitation, court costs and reasonable
attorneys' fees and expenses. The application of the United Nations Convention on Contracts for the International Sale
of Goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed
against the drafter shall not apply to this License.
12. RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and
Contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.
13. MULTIPLE-LICENSED CODE.
Initial Developer may designate portions of the Covered Code as "Multiple-Licensed". "Multiple-Licensed" means
that the Initial Developer permits you to utilize portions of the Covered Code under Your choice of the NPL or the alternative licenses, if any, specified by the Initial Developer in the file described in Exhibit A.
EXHIBIT A -Mozilla Public License.
``The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this
file except in compliance with the License. You may obtain a copy of the License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND,
either express or implied. See the License for the specific language governing rights and limitations under the License.
The Original Code is ______________________________________.
The Initial Developer of the Original Code is ________________________.
Portions created by ______________________ are Copyright (C) ______
_______________________. All Rights Reserved.
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in
which case the provisions of [______] License are applicable instead of those above. If you wish to allow use of your
version of this file only under the terms of the [____] License and not to allow others to use your version of this file
under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other
provisions required by the [___] License. If you do not delete the provisions above, a recipient may use your version of
this file under either the MPL or the [___] License."
APPENDIX
152
[NOTE: The text of this Exhibit A may differ slightly from the text of the notices in the Source Code files of the
Original Code. You should use the text of this Exhibit A rather than the text found in the Original Code Source Code for
Your Modifications.]
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
Model :
Serial No. :
Trade Mark of the DVB Digital Video
Broadcasting Project (1991 to 1996)
Download PDF