LG | 55LY340C | LG 55LY340C Owner’s Manual

OWNER’S MANUAL
LED TV*
* Disclaimer
LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
LY33**
LY34**
LY54**
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
LICENSES
20 TROUBLESHOOTING
3
OPEN SOURCE SOFTWARE
NOTICE
21 SPECIFICATIONS
4
4
6
7
8
9
9
10
11
ASSEMBLING AND
PREPARING
Unpacking
Parts and Button
Using the Joystick Button
Lifting and Moving the TV
Setting up the TV
-Attaching the Stand
-Mounting on a Table
-Mounting on a Wall
23 IR CODES
24 EXTERNAL CONTROL DEVICE
SETUP
24
24
24
25
25
26
RS-232C Setup
Type of Connector:
D-Sub 9-Pin Male
RS-232C Configurations
Communication Parameters
Command Reference List
Transmission / Receiving Protocol
12 MAKING CONNECTIONS
12
13
13
13
14
Antenna Connection
Adapter Connection
Network Setup
-Wired Network Connection
Other Connections
18 REMOTE CONTROL
20 MAINTENANCE
20
20
20
Cleaning your TV
-Screen, Frame, Cabinet and Stand
-Power Cord
WARNING
yy If you ignore the warning message, you may
be seriously injured or there is a possibility
of accident or death.
CAUTION
yy If you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
yy The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo
are trademarks or registered trademarks of HDMI Licensing LLC in the United States
and other countries.
ABOUT DIVX VIDEO:DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that has
passed rigorous testing to verify that it plays DivX video. Visit divx.com for more
information and software tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or
its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
ENGLISH
ENG
LICENSES
4
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yy Image shown may differ from your TV.
yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy The available menus and options may differ from the input source or product model that you are
using.
yy New features may be added to this TV in the future.
yy The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
be turned off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the picture
is reduced, and this will reduce the overall running cost.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to upgrade
of product functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB FLASH
DRIVE does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
< 18 mm
*B =
ENGLISH
ENG
ENGLISH
ENG
ASSEMBLING AND PREPARING
5
ENGLISH
ENG
Remote Control,
Batteries (AAA)
Owner’s Manual
Cable Holder
(Depending on model)
Power Cord
(Depending on model)
Stand Screws
4EA, M4 x L14
(Only 42/47LY34**,
39/42/47/55LY54**)
Stand Screws
4EA, M4 x L20
(Only 32LY34**, 32LY54**)
Cable Managements
2EA
(Only 32/42/47LY34**,
32/39/42/47/55LY54**)
Wall Mount Spacers
2EA
(Only 42LY34**, 42LY54**)
Stand Base
(Only 32/42/47LY34**,
32/39/42/47/55LY54**)
AC-DC Adaptor
(Only 28LY33**)
(Depending on model &
country)
or
Stand Base
(Only 28LY33**)
(Depending on model &
country)
6
ASSEMBLING AND PREPARING
ENG
ENGLISH
Parts and Button
A type : 32/42/47LY34**, 32/39/42/47/55LY54**
B type : 28LY33** (Except for India)
Screen
Screen
Speakers
Speakers
Remote control sensor
Power Indicator
Joystick button1
Remote control sensor
Power Indicator
Joystick button1
C type : 28LY33** (Only India)
Screen
Speakers
Remote Control Sensor
Power Indicator
Joystick Button1
1 Joystick Button - This button is located below the TV screen.
NOTE
yy You can set the power indicator light to on or off by selecting OPTION in the main menus.
ASSEMBLING AND PREPARING
7
You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right.
Basic Functions
Power On
When the TV is turned off, place your finger on the joystick button
and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick button
and press it once for a few seconds and release it.
(However, if the Menu button is on the screen, pressing and
holding the joystick button will let you exit the Menu.)
Volume
Control
If you place your finger over the joystick button and move it left or
right, you can adjust the volume level you want.
Programmes
Control
If you place your finger over the joystick button and move it up or
down, you can scrolls through the saved programmes you want.
NOTE
yy When your finger over the joystick button and push it to the up, down, left or right, be careful not to
press the joystick button. If you press the joystick button first, you can not adjust the volume level and
saved chennels.
Adjusting the Menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items ( , , , ) moving the joystick button up, down, left or right.
TV Off
Turn the power off.
Settings
Accesses the main menu.
Input List
Changes the input source.
Close
Clears on-screen displays and return to TV viewing.
ENGLISH
ENG
Using the Joystick Button
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and Moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
yy When transporting a large TV, there should
be at least 2 people.
yy When transporting the TV by hand, hold the
TV as shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as
this may result in damage to the screen.
yy It is recommended to move the TV in the
box or packing material that the TV originally
came in.
yy Before moving or lifting the TV, disconnect
the power cord and all cables.
yy When holding the TV, the screen should
face away from you to avoid damage.
yy When transporting the TV, do not expose
the TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
yy Do not apply excessive pressure to cause
flexing /bending of frame chassis as it may
damage screen.
CAUTION
yy When handling the TV, be careful not to
damage the protruding joystick button.
(Depending on model)
yy Hold the top and bottom of the TV frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the TV
Attaching the Stand
* Image shown may differ from your TV.
(Only 32/42/47LY34**, 32/39/42/47/55LY54**)
(Only 28LY33**)
1
1
1
2
A Stand Base
B Stand Base
Stand Base
2
2
M4 x L14
(Only 42/47LY34**,
39/42/47/55LY54**)
M4 x L20
4EA (Only 32LY34**,
32LY54**)
9
CAUTION
yy When attaching the stand to the TV, place
the screen facing down on a cushioned
table or flat surface to protect the screen
from scratches.
10 ASSEMBLING AND PREPARING
ENG
ENGLISH
Mounting on a Table
Securing the TV to a Wall
1 Lift and tilt the TV into its upright position on a
table.
-- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
(This feature is not available for all models.)
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
yy Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
WARNING
yy If a television is not positioned in a
sufficiently stable location, it can be
potentially hazardous due to falling. Many
injuries, particularly to children, can be
avoided by taking simple precautions such
as:
»» Using cabinets or stands recommended
by the manufacturer of the television.
»» Only using furniture that can safely
support the television.
»» Ensuring the television is not
overhanging the edge of the supporting
furniture.
»» Not placing the television on tall furniture
(for example, cupboards or bookcases)
without anchoring both the furniture and
the television to a suitable support.
»» Not standing the televisions on cloth
or other materials placed between the
television and supporting furniture.
»» Educating children about the dangers
of climbing on furniture to reach the
television or its controls.
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
yy Make sure that children do not climb on or
hang on the TV.
NOTE
yy Use a platform or cabinet that is strong and
large enough to support the TV securely.
yy Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
ASSEMBLING AND PREPARING
CAUTION
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm
10 cm
yy Disconnect the power first, and then move
or install the TV. Otherwise electric shock
may occur.
yy If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and
contact the local dealer or qualified
personnel.
yy Do not over tighten the screws as this may
cause damage to the TV and void your
warranty.
yy Use the screws and wall mounts that meet
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the manufacturer’s
warranty.
yy Screw length from outer surface of back
cover should be under 8mm.
(Only 28LY33**)
Wall mount Pad
10 cm
Back Cover
Separate Purchase(Wall Mounting Bracket)
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in
the following table.
Model
28LY33**
VESA (A x B)
100 x 100
Standard screw M4 X L10
Number of screws 4
Wall mount bracket LSW140B
42/47/55LY54**
42/47LY34**
VESA (A x B)
400 x 400
Standard screw M6
Number of screws 4
LSW440B
Wall mount bracket
MSW240
Model
32LY34**
32/39LY54**
200 x 200
M6
4
LSW240B
MSW240
Wall mount Pad
Back Cover
Standard screw
: M4 x L10
Max.8mm
NOTE
yy Use the screws that are listed on the VESA
standard screw specifications.
yy The wall mount kit includes an installation
manual and necessary parts.
yy The wall mount bracket is not provided. You
can obtain additional accessories from your
local dealer.
yy The length of screws may differ depending
on the wall mount. Make sure to use the
proper length.
yy For more information, refer to the manual
supplied with the wall mount.
NOTE
yy Only 42LY34**, 42LY54**
A
B
Wall Mount
Spacers
ENGLISH
ENG
Mounting on a Wall
10 cm
11
12 MAKING CONNECTIONS
ENG
ENGLISH
MAKING
CONNECTIONS
Antenna Connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
* Image shown may differ from your TV.
* Any separate cable is not provided.
This section on MAKING CONNECTIONS mainly
uses diagrams for the LY34** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information on external device’s
connection, refer to the manual provided with each
device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
ANTENNA/
CABLE IN
Wall Antenna
Socket
NOTE
yy The external device connection may differ
from the model.
yy Connect external devices to the TV
regardless of the order of the TV port.
yy If you record a TV program on a DVD
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
on recording, refer to the manual provided
with the connected device.
yy Refer to the external equipment’s manual for
operating instructions.
yy If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
yy In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE
menu until the picture is clear.
yy In PC mode, some resolution settings may
not work properly depending on the graphics
card.
yy Only a USB storage device is recognizable.
yy If the USB storage device is connected
through a USB hub, the device is not
recognizable.
yy Using a DVI to HDMI cable may cause
compatibility issues.
NOTE
yy Use a signal splitter to use more than 2 TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
yy If the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
yy An antenna cable and converter are not
supplied.
yy Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
MAKING CONNECTIONS
Network Setup
Wired Network Connection
(Only 28LY33**)
(Depending on model & country)
(Only LY54**)
This TV can be connected to a local area network
(LAN) via the LAN port. After making the physical
connection, the TV needs to be set up for network
communication.
(Image shown may differ from your TV.)
DC-IN
(19V
)
AC-DC Adapter
LAN
or
Broadband Modem
Router
Broadband Service
DC-IN
(19V
)
Broadband Modem
Broadband Service
AC-DC Adapter
CAUTION
yy Please be sure to connect the TV to the ACDC power adapter before connecting the
TV’s power plug to a wall power outlet.
Connect the LAN port of the Modem or Router to
the LAN port on the TV.
CAUTION
yy Do not connect a modular phone cable to
the LAN port.
yy Since there are various connection methods,
please follow the specifications of your
telecommunication carrier or internet service
provider.
ENGLISH
ENG
Adapter Connection
13
14 MAKING CONNECTIONS
ENG
ENGLISH
Other Connections
Connect your TV to external devices. For the best picture and audio quality, connect the external device
and the TV with the HDMI cable as shown.
* Image shown may differ from your TV.
* Any separate cable is not provided.
(Only 32/42/47LY34**, 32/39/42/47/55LY54**)
/DVI IN
1
2
AV
(RGB)
IN
AUDIO IN
PONENT
OPTICAL
OPTICAL AUDIO OUT
(COMPONENT/RGB/DVI)
IN
1
DIGITAL
AUDIO OUT
ERNAL
ER OUT
EAKER
P OUT OUT
EXTERNAL
SPEAKER OUT
DIO IN
NENT/DVI)
H/P OUT
UME CONTROL
1 AUDIO IN
IN
OPTICAL
CLOCK
DIGITAL
1
AUDIO OUT
/DVI IN
2
AV
RS-232C IN
PCMCIA CARD SLOT
LNB IN
OPTICAL
ANTENNA/
CABLESatellite
IN
DIGITAL
AUDIO OUT
OPTICAL
DIGITAL
AUDIO OUT
RS-232C IN
COMPONENT
IN
IN
EXTERNAL
STEREO
(8 Ω)
SPEAKER OUT
VOLUME
CONTROL
ANTENNA/
ANTENNA/
IN
CABLEIN
CABLE
1
1
RS-232C IN
RGB IN (PC)
OPTICAL
(CONTROL
& SERVICE)
(CONTROL & SERVICE)
DIGITAL
IN
COMPONENT
IN
ANTENNA/ 1
LNB IN ANTENNA/
CABLEIN
Satellite CABLE
RGB IN (PC)
RS-232C IN (CONTROL & SERVICE)
EXTERNAL
SPEAKER OUT
AV
(RGB)
H/P OUT
AUDIO IN
(COMPONENT/RGB/DVI)
EXTERNAL
LNB IN ANTENNA/
Satellite CABLE IN
RS-232C IN
CLOCK
(CONTROL & SERVICE)
HDMI
USB IN
SPEAKER OUT
COMPONENT
IN
VOLUME
AUDIO IN CONTROL
(COMPONENT/RGB/DVI)
AUDIO IN
EXTERNAL
(COMPONENT/DVI)
SPEAKER OUT
AUDIO IN
(COMPONENT/RGB/DVI)
H/P OUT
AUDIO IN
(COMPONENT/RGB/DVI)
ble Box
H/P OUT
VOLUME
COMPONENT
CONTROL
IN
AUDIO IN
AUDIO(COMPONENT/DVI)
IN
RGB IN (PC) (COMPONENT/RGB/DVI)
RGB IN (PC)
COMPONENT
H/P OUT
AUDIO OUT IN
RGB OUT(PC)
AUDIO / VIDEO
AUDIO / VIDEO
OPTICAL
AUDIO
OPTICAL AUDIO
IN IN
H/P OUT
RGB IN (PC)
DigitalAudio
Audio System
Digital
Systerm
Digital Audio System
ANTENNA/
CABLE
EXTERNAL
SPEAKER OUT
AUDIO OUT
AUDIO IN
(COMPONENT/DVI)
EXTERNAL
SPEAKER OUT
VOLUME& SERVICE)
RS-232C IN (CONTROL
CONTROL
RGB IN (PC)
(CONTROL
& SERVICE)
(CONTROL & SERVICE)
VOLUME CONTROL
H/P OUT
VOLUME
CONTROL
RGB IN (PC)
SPEAKER
H/P OUT OUT
IN 3
(Only LY54**)
AV
(RGB)
(COMPONENT/RGB/DVI)
(RGB)
IN
AUDIO IN
COMPONENT
OPTICAL
OPTICAL AUDIO OUT
(COMPONENT/RGB/DVI)
ONENTIN COMPONENT
1
DIGITAL
EXTERNAL
N SPEAKER OUT IN
AUDIO OUT
AV
TEREO (8 Ω)
RS-232C IN
RGB IN (RGB)
(PC)
(CONTROL
CLOCK
RS-232C
IN & SERVICE)
AUDIO IN
(COMPONENT/DVI)
(Only Support Network Model)
AV
(RGB)
PC
RGB IN (PC)
IN
1
AV
(RGB)
ANTENNA/OPTICAL
CABLE DIGITAL
AUDIO OUT
ANTENNA/
CABLE IN
EXTERNAL
SPEAKER OUT
OPTICAL
VOLUME
RS-232C IN
RGB IN (PC) DIGITAL
AUDIO OUT
(CONTROL & SERVICE)
CONTROL
AUDIO IN
UP
+
(COMPONENT/DVI)
+
-
-
DOWN
OPTICAL
IN
1
AV
OPTICAL
(RGB)
DIGITAL
AUDIO OUT
IN
1
Control port
for Speaker outAV
(RGB)
LN
Sate
EXTERNAL DIGITAL
COMPONENT
SPEAKER
IN OUT AUDIO OUT
RS-232C IN
RS-232C IN OPTICAL
CLOCK
CLOCK
DIGITAL
VOLUME & SERVICE)
(CONTROL
(CONTROL
& SERVICE)
GND
LN
AUDIO
OUT
CONTROL RIGHT
Satel
AUDIO IN
(COMPONENT/DVI) LEFT
GND
RS-232C IN
CLOCK
COMPONENT
(CONTROL & SERVICE)
IN
RS-232C IN
CLOCK
(CONTROL & SERVICE)
OPTICAL AUDIO IN
MAKING CONNECTIONS
15
ENG
USB IN 2
ENGLISH
ENG
(Only 32/42/47LY34**, 32/39/42/47/55LY54**)
H/P OUT
2
USB
HUB
HUB
USB
MHL passive
cable
HUB
Mobile Phone
Mobile Phone
VOLUME Headphone
CONTROL
AV
IN
EXTERNAL
SPEAKER OUT
1
IN
ANTENNA/
AUDIO
LNB IN ANTENNA/
CABLE
Satellite CABLE IN
EXTERNAL
AUDIO
COMPONENT
RGB IN (PC)IN RGB
RS-232C
IN (CONTROLRS-232C
& SERVICE)
IN (PC)
IN (CONTROL & SERVICE)
STEREO (8 Ω)
RS-232C IN
CABLE
IN 3
RED
BLUE
WHITE
BLUE
GREEN
RED
GREEN
1(ARC)
ANTENNA/
RGB
IN (PC) ANTENNA/
(CONTROL
& SERVICE)
(CONTROL & SERVICE)
CABLE
H/P OUT
/DVI IN
EXTERNAL
2
IN
SPEAKER OUT
1
RS-232C
IN SPEAKER OUT
ANTENNA/
CABLE
1(ARC)
OPTICAL
VOLUMEIN
CONTROL
DIGITAL AUDIO 1
AUDIO OUT AUDIO
/DVI IN
3
3
RS-232C IN (CONTROL & SERVICE)
CONTROL
2
AUDIO IN
(COMPONENT/DVI) IN
Mobile Phone
Mobile Phone
(RGB)
IN
AUDIO IN
COMPONENT
OPTICAL OPTICAL
OPTICAL AUDIO OUT DIGITAL 1
(COMPONENT/RGB/DVI)
IN
AUDIO OUT
DIGITAL
EXTERNAL
AUDIO OUT
SPEAKER OUT
AV
RGB IN (PC)
(RGB)
CLOCK
VOLUME
SPEAKER
IN
H/P OUT OUT
CONTROL VOLUME
LAN
L
HDMI
DVI OUT
AUDIO OUT
DVI OUT
AUDIO OUT
VIDEO
AUDIO OUT
RED
WHITE
RED
USB IN
OPTICAL
DIGITAL
AUDIO OUT
PCMCIA CARD SLOT
1
USB
PCMCIA Card
H/P OUT
2 (MHL)
H/P H/P
OUT OUT
USB IN 1
IN
2 (MHL)
/DVI IN
USB
R
AUDIO
D/ Blu-Ray / HD Cable Box
D STB / PC
Blu-Ray / HD STB / HD Cable Box / DVD / PC
OPTICAL AUDIO IN
/ HD Box
DVD
/ HD Cable
AUDIO/DVD/
/Blu-Ray
VIDEOBlu-Ray
Cable Box
DVI OUT
L (MONO)
ENGLISH
ENG
USB IN 2
IN INUSB IN 1
IN 2 IN 2
USB IN 1 USBUSB
IN 2 (MHL)
2 (MHL)
USB
IN 1
PCMCIA Card
PCMCIA Card
16 MAKING CONNECTIONS
ENG
ENGLISH
(Only 28LY33**)
+
-
/DVI IN
1
2
AV
AV
(RGB)
CLOCK
KER OUT OPTICAL
OUT
DIGITAL
AUDIO OUT
/DVI IN
IN
NT/DVI)
ME CONTROL
1
IN1
OPTICAL
DIGITAL
AUDIO OUT
AVRS-232C IN
2
RGB IN (PC)
AUDIO IN
COMPONENT
OPTICAL
OPTICAL AUDIO OUT
(COMPONENT/RGB/DVI)
NENTIN
RS-232C IN
DIGITAL
AUDIO OUT
EXTERNAL
SPEAKER OUT
REO (8 Ω)
SPEAKER
H/P OUT OUT
AUDIO IN
OMPONENT/DVI)
STEREO (8 Ω)
LEFT
GND
EXTERNAL
SPEAKER
OUT IN1
LNB IN ANTENNA/
1 RGB IN (PC)
(CONTROL & SERVICE)
AV
(RGB)
CLOCK
RS-232C
IN
ANTENNA
/CABLE IN
RGB IN (PC)
L
COMPONENT IN
ANTENNA/
LNB IN ANTENNA/
CABLEIN
L (MONO) Satellite R CABLE
RS-232C IN
DC-IN
(19V
EXTERNAL
SPEAKER
OUT
ANTENNA/
(CONTROL & SERVICE)
CABLEIN
(RGB)
IN
CABLE
SatelliteRS-232C
IN
IN
(CONTROL
& SERVICE)
(CONTROLCOMPONENT
& SERVICE)
VOLUME CONTROL
DC-IN
(19V
)
OMPONENT
IN
1
DIGITAL
AUDIO OUT
NAL
R OUT
GND
RIGHT
(RGB)
IN
AUDIO IN
ONENT
OPTICAL
OPTICAL AUDIO OUT
(COMPONENT/RGB/DVI)
N
L
L (MONO)
)
RS-232C IN
RGB IN (PC)
(CONTROL
& SERVICE)
(CONTROL & SERVICE)
ANTENNA
/CABLE IN
R
COMPONENT IN
COMPONENT IN
L
L
R
L (MONO)
R
L (MONO)
RED
WHITE
YELLOW
RED
RED
RED
BLUE
WHITE
BLUE
GREEN
DMI
Box
AUDIO / VIDEO
DigitalAudio
Audio System
Digital
Systerm
Digital Audio System
RED
VIDEO
WHITE
L
RED
WHITE
AUDIO OUT
RGB OUT(PC)
GREEN
OPTICAL
AUDIO
OPTICAL AUDIO
IN IN
YELLOW
AUDIO / VIDEO
R
AUDIO
VIDEO L(MONO) -AUDIO-R
PC
DVD // Blu-Ray
Blu-Ray // HD
DVD
HD Cable
Cable
BoxBox
DVD/ /Blu-Ray
Blu-Ray / HD Cable
DVD
HD/Cable
Box
VCR Box / VCR
MAKING CONNECTIONS
17
CLOCK
USB IN 2
HUB
USB
USB
HUB
MHL passive
cable
HUB
H/P 2OUT
(MHL)
AV
1
Mobile Phone
AV
(RGB)
H/P OUT
H/P OUT
/DVI IN
AUDIO
IN
OPTICAL
OPTICAL
IN1
(COMPONENT/DVI)
DIGITAL IN
DIGITAL LAN VOLUME
AUDIOAUDIO
OUTCONTROL
AUDIO OUT
AUDIO
EXTERNAL
EXTERNAL
SPEAKERSPEAKER
OUT
OUTIN
RS-232C
2
IN1
RS-232C IN
COMPONENTRGB IN (PC)
(CONTROL & SERVICE)
RS-232C
IN
IN
RS-232C IN
ANTENNA/
LNB IN ANTENNA/
CABLEIN
Satellite CABLE
1(ARC)
RGB IN (PC)
(CONTROL
& SERVICE)
(CONTROL & SERVICE)
COMPONENT IN
DC-IN
(19V
HDMI
L
L (MONO)
L
R
ANTENNA
/CABLE IN
ANTENNA
/CABLE IN
R
L (MONO)
)
Mobile Phone
Headphone
RGB IN (PC)STEREO (8(CONTROL
& SERVICE)
Ω)
DC-IN
COMPONENT
IN
(19V
)
Mobile Phone
Mobile Phone
3
SPEAKER
H/P OUT OUT
USB
IN 2IN 1
USB
IN 2IN 2
USB
USB
IN 1
(MHL)
USB IN
IN1
IN
2 (MHL)
DIGITAL
AUDIO OUT
EXTERNAL
SPEAKER OUT
USB
PCMCIA Card
(RGB)
IN
IN
AUDIO IN
COMPONENT
OPTICAL
OPTICAL AUDIO OUT
(COMPONENT/RGB/DVI)
IN
USB
(MHL)
H/P2 OUT
2
PCMCIA Card
USB IN 2
1
H/P OUT
/DVI IN
PCMCIA Card
USB IN 1
IN 2
(MHL)
USB IN 1
USB IN 2
ENGLISH
ENG
(Only 28LY33**)
DVI OUT
AUDIO OUT
DVI OUT
AUDIO OUT
DVD/ Blu-Ray / HD Cable Box
HD STB / PC
Blu-Ray / HD STB / HD Cable Box / DVD / PC
OPTICAL AUDIO IN
Digital Audio System
AUDIO / VIDEO
18 REMOTE CONTROL
The descriptions in this manual are based on the buttons on the
remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries
(1.5 V AAA) matching the
and
ends to the label inside the
compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
or
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
yy In Analogue TV and some countries, some remote control buttons may not work.
Make sure to point the remote control toward the remote control sensor on the TV.
(Only LY33**, LY34**)
TV/
RAD
AV MODE
(POWER) Turns
the
RATIO
INPUT TV on or off.
TV/RAD
Selects Radio, TV and DTV programme.
SUBTITLE Recalls your preferred subtitle in digital mode.
AV MODE Selects an AV mode.
RATIO
Resizes
.,;@
abc an image.
def
INPUT
Changes the input source.
1
2
4
5
ghi
Number buttons
3
6
jklEnters
mno
numbers.
LIST Accesses the saved programme list.
pqrs
tuv
Q.VIEW Returns
to the wxyz
previously viewed programme.
7
+
MUTE
9
0
- Adjusts
Q.VIEWlevel.
LIST the volume
FAV Accesses your favourite programme list.
GUIDE Shows FAV
programme guide.
FAV
GUIDE
8
[
ENG
ENGLISH
REMOTE CONTROL
P
PAGE
MUTE
Mutes all sounds. PA
P GE programmes or channels.
ꕌPꕍ Scrolls through the saved
MUTE to the previous or next screen.
ꕌPAGEꕍ Moves
Teletext buttons ( TEXT/T.OPT) These buttons are used for teletext.
INFO SETTINGS
Views the information
of the current programme and screen.
MY APPS
SETTINGS Accesses the main menus.
Q.MENU Accesses the quick menus.
OK or options and confirms your input.
OK
Selects menus
Navigation buttons (up/down/left/right) Scrolls through menus or options.
BACK Returns to the previous level.
EXIT Clears all on-screen displays and return to TV viewing.
SLEEP
REC
EXIT
Accesses the AV devices connected with the HDMI cable
through HDMI-CEC. Opens the SIMPLINK menu.
SLEEP Sets the sleep timer.
Control buttons (
) Controls the MY MEDIA menus, or the
SIMPLINK compatible devices (USB,SIMPLINK).
SUBTITLE
LIVE TV
Colour buttons
INFO
These access special functions in some menus.
( REC
: Red,
: Green,
: Yellow,
: Blue)
REMOTE CONTROL
19
ENERGY
AV MODE
ENGLISH
ENG
(Only LY54**)
(POWER) Turns the TV on or off.
ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce
energy consumption.
AV MODE Selects an AV mode.
INPUT Changes the input source.
TV/RAD
Selects Radio, TV and DTV programme.
INPUT
TV/
RAD
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
Number buttons Enters numbers.
LIST Accesses the saved programme list.
Q.VIEW Returns to the previously viewed programme.
FAV
RATIO
P
MUTE
GUIDE PORTAL INFO
OK
SETTINGS
EXIT
P
A
G
E
+
- Adjusts the volume level.
FAV Accesses your favourite programme list.
RATIO Resizes an image.
MUTE
Mutes all sounds.
ꕌPꕍ Scrolls through the saved programmes or channels.
PAGE Moves to the previous or next screen.
GUIDE Shows programme guide.
PORTAL Displays and removes hotel interactive menu.
INFO
Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus or
options.
OK
Selects menus or options and confirms your input.
SETTINGS Selects a menu. Clears all on-screen displays and
returns to TV viewing from any menu.
Returns to the previous level.
EXIT Clears on-screen displays and return to TV viewing.
Colour buttons
Q.MENU
These access special functions in some menus.
( : Red,
: Green,
: Yellow,
: Blue)
Teletext buttons ( TEXT/T.OPT) These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Control buttons (
)
Controls the MY MEDIA menus, or the SIMPLINK compatible devices
(USB, SIMPLINK).
Accesses the AV devices connected with the HDMI
cable through HDMI-CEC. Opens the SIMPLINK menu.
Q.MENU Accesses the Quick menus.
20 MAINTENANCE / TROUBLESHOOTING
ENG
ENGLISH
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall
outlet to prevent possible damage from lightning or power surges.
Screen, Frame, Cabinet and Stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in
scratches and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power Cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
The software version can be updated for improvement in performance.Customer needs to ensure the
compatibility of customer’s equipment with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Problem
Solution
Cannot control
the TV with the
remote control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to , to ).
yy Check if the batteries are still working and properly installed (
No image display
and no sound is
produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Auto sleep feature is activated in the Time settings.
When connecting
to the PC (RGB/
HDMI DVI),
‘No signal’ or
‘Invalid Format’ is
displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the RGB/HDMI DVI cable.
yy Restart the PC with the TV on.
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
MODELS
32LY34**
42LY34**
47LY34**
32LY340C-TA
42LY340C-TA
47LY340C-TA
Dimensions
(W x H x D)
With stand (mm)
732 x 481 x 207
961 x 612 x 218
1073 x 676 x 247
Without stand (mm)
732 x 431 x 55.5
961 x 567 x 55.5
1073 x 629 x 55.8
Weight
With stand (kg)
6.2
9.5
12.7
Without stand (kg)
6.0
9.2
12.3
Power requirement
AC 100-240 V~ 50 / 60 Hz
MODELS
32LY54**
39LY54**
42LY54**
32LY540H-TA
39LY540H-TA
42LY540H-TA
Dimensions
(W x H x D)
With stand (mm)
732 x 481 x 207
885 x 567 x 218
961 x 612 x 218
Without stand (mm)
732 x 431 x 55.5
885 x 524 x 55.5
961 x 567 x 55.5
Weight
With stand (kg)
6.2
8.3
9.5
Without stand (kg)
6.0
8.0
9.2
Power requirement
AC 100-240 V~ 50 / 60 Hz
47LY54**
MODELS
55LY54**
28LY33**
47LY540H-TA
55LY540H-TA
28LY330C-TA
Dimensions
(W x H x D)
With stand (mm)
1073 x 676 x 247
1243 x 772 x 247
641.5 x 432 x 170
Without stand (mm)
1073 x 629 x 55.8
1243 x 725 x 56.8
641.5 x 395.8 x 57.6
Weight
With stand (kg)
12.7
18.4
4.5
Without stand (kg)
12.3
18.0
4.2
Power requirement
AC 100-240 V~ 50 / 60 Hz
Manufacturer : APD
Model : DA-48F19
Manufacturer : APD
Model : DA-40I19
AC/DC Adapter
Environment
condition
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Television System
19 V
Digital TV
(Depend on Country)
Analogue TV
(Depend on Country)
DVB-T (*DVB-T/T2)
PAL B/B, PAL B/G, PAL D/K, PAL-I
SECAM B/G, SECAM D/K
NTSC-M
VHF, UHF
VHF, UHF, CATV
Programme Coverage
Maximum number of
storable programmes
External Antenna
Impedance
* : Only DVB-T2 support models.
DVB-T& Analogue TV : 1,500
75 Ω
2.0 A
ENGLISH
ENG
SPECIFICATIONS
21
22 SPECIFICATIONS
ENG
ENGLISH
RGB-PC, HDMI/PC Supported Mode
Component Port Connecting Information
Component ports on the
TV
Y
Video output ports
on DVD player
PR
PR
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
Y
PR
PR
Y
B-Y
R-Y
640 x 480
31.469
59.94
Y
Cb
Cr
800 x 600
37.879
60.31
Y
Pb
Pr
1024 x 768
48.363
60.00
1280 x 768
47.776
59.870
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
1152 x 864
54.348
60.053
1360 x 768
47.712
60.015
1280 x 1024
(HDMI-PC)
63.981
60.020
1920 x 1080
(HDMI-PC)
67.50
60.00
(Except for 32LY340C, 32LY540H)
NOTE
HDMI/DTV Supported Mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720 x 480
31.469
31.5
59.94
60
720 x 576
31.25
50
1280 x 720
37.500
44.96
45
50
59.94
60
1920 x 1080i
33.72
33.75
28.125
59.94
60
50.00
1920 x 1080p
26.97
27
33.716
33.75
56.250
67.43
67.5
23.97
24
29.976
30.00
50
59.94
60
yy The optimal display resolution
- 28LY33** : 1360 X 768 @60Hz
yy The optimal timing in each mode is vertical
frequency 60Hz.
IR CODES
yy This feature is not available for all models.
Code (Hexa)
Function
08
(POWER)
Note
Remote control Button (Power On/Off)
F0
TV/RAD
Remote control Button
39
SUBTITLE
Remote control Button
30
AV MODE
Remote control Button
79
RATIO
Remote control Button
0B
INPUT
Remote control Button
10-19
Number Key 0-9
Remote control Button
53
LIST
Remote control Button
1A
Q.VIEW
Remote control Button
02
+
Remote control Button
03
-
Remote control Button
1E
FAV
Remote control Button
AB
GUIDE
Remote control Button
09
MUTE
Remote control Button
00
P ꕌ / PAGE ꕌ
Remote control Button
01
P ꕌ / PAGE ꕌ
Remote control Button
20
TEXT
Remote control Button
21
T.OPT(T.Option)
Remote control Button
43
SETTINGS
Remote control Button
45
Q.MENU
Remote control Button
AA
INFO
Remote control Button
28
BACK
Remote control Button
5B
EXIT
Remote control Button
44
OK
Remote control Button
40
^
v
Remote control Button
41
07
<
Remote control Button
06
>
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
B1
n
Remote control Button
B0
►
yy
Remote control Button
BA
8E
►►
Remote control Button
8F
◄◄
Remote control Button
7E
SIMPLINK
Remote control Button
0C
PORTAL
Remote control Button
95
ENERGY SAVING
Remote control Button
0E
SLEEP
Remote control Button
Remote control Button
Remote control Button
ENGLISH
ENG
IR CODES
23
24 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup
RS-232C Configurations
Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control
system) to control the product’s functions externally.
VOLUME
CONTROL
Connect the serial port of the control device to the
RS232C jack on the product back panel.
IN are not supplied with
OPTICAL
Note:
RS-232C connection cables
EXTERNAL
DIGITAL
1
SPEAKER OUT
the
product.
AUDIO OUT
RGB IN (PC)
RS-232C IN (CONTROL & SERVICE)
7-Wire Configurations
(Standard RS-232C cable)
ANTENNA/ CABLE
RXD TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations
(Not standard)
(*Not Provided)
Type of Connector:
D-Sub 9-Pin Male
1
5
RXD TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Set ID number. "Real Data Mapping".
1 Press SETTINGS or HOME to access the main
menus.
2 Press the Navigation buttons to scroll to
OPTION and press OK.
6
No.
9
Pin name
1
3.5V
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
No Connection (5V available in some models)
8
No Connection
9
No Connection (12V available in some models)
3 Press the Navigation buttons to scroll to Set ID
and press OK.
4 Scroll left or right to select a set ID number and
select Close. The adjustment range is 1-99.
5 When you are finished, press EXIT.
EXTERNAL CONTROL DEVICE SETUP
25
yy Baud rate: 9600 bps (UART)
yy Data length: 8 bits
yy Parity : None
ENGLISH
ENG
Communication Parameters
yy Stop bit: 1 bit
yy Communication code: ASCII code
yy Use a crossed (reverse) cable.
Command Reference List
(Depending on Model)
model)
01. Power
02. Aspect
Ratio
03. Screen
Mute
04. Volume
Mute
05. Volume
Control
k
a
DATA
(Hexadecimal)
00 to 01
k
c
(See p. 27)
k
d
(See p. 27)
k
e
00 to 01
k
f
00 to 64
06. Contrast
k
g
00 to 64
07. Brightness
k
h
00 to 64
08. Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 32
11. OSD Select k
l
00 to 01
12. Remote
Control
Lock Mode
m
00 to 01
COMMAND1
k
COMMAND2
13. Balance
14. Colour
Temperature
15. Energy
Saving
16. Auto Configuration
k
t
DATA
(Hexadecimal)
00 to 64
x
u
00 to 64
j
q
00 to 05
j
u
01
17. Equalize
j
v
(See p. 29)
m
a
(See p. 29)
m
b
00 to 01
m
m
c
g
(See p. 29)
00 to 64
x
b
(See p. 30)
COMMAND1
18. Tune Command
19. Programme
Add/Skip
20. Key
21. Control
Back Light
22. Input select
(Main)
COMMAND2
* Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are not
executed and treated as NG.
26 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]
[Command 2]
[Set ID]
: First command to control the TV.(j, k, m or x)
: Second command to control the TV.
: You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment
range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ]
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data00: Illegal Code
EXTERNAL CONTROL DEVICE SETUP
27
04. Volume Mute (Command: k e)
►► To control Power On/Off of the set.
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on remote
control.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data based on this
format, Acknowledgement data feed back presents status
about each function.
* OK Ack., Error Ack. and other message may display on the
screen when TV is power On.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
02. Aspect Ratio (Command: k c) (Main Picture
Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the Aspect
Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen
(16:9)
04 : Zoom
06 : Original
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect
ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p
24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i,
1080p 50 Hz / 60 Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital, Analogue, AV.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 :
01 :
10 :
Screen mute off (Picture on)
Video mute off
Screen mute on (Picture off)
Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen
Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
01. Power (Command: k a)
28 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
09. Tint (Command: k j)
13. Balance (Command: k t)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
14. Colour Temperature (Command: x u)
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Data Min : 00 to Max : 32
* Refer to ‘Real data mapping’. See p.30.
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling
remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
15. Energy Saving (Command: j q)
►► To reduce the power consumption of the TV. You can also
adjust Energy Saving in PICTURE menu.
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function
12. Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and remote
control.
7
6
5
4
0
0
0
0
0
0
0
01 : Lock on
0
0
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
0
* If you are not using the remote control, use this mode.
When main power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by
power on key of IR & Local Key.
Description
3
2
1
0
Low
Power
0
0
0
0
Off
0
Low
Power
0
0
0
1
Minimum
0
0
Low
Power
0
0
1
0
Medium
0
0
0
Low
Power
0
0
1
1
Maximum
0
0
0
0
Low
Power
0
1
0
1
Screen Off
0
0
0
0
Low
Power
0
1
0
0
Auto
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
Level
►► 'Auto' is available in TV that supports 'Intelligent Sensor'
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
►► Select channel to following physical number.
►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data00 :High channel data
Data01 :Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 :[Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
Data 01: To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. Equalize(Command: j v)
►► To adjust equalize.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
0
0
0
0
Frequency
0
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
LSB
0
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
0
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
1’st Band
0
0
0
0
0
0(decimal)
0
0
1
2’nd Band
0
0
0
0
1
1(decimal)
0
1
0
3’rd Band
...
...
...
...
...
...
0
1
1
4’th Band
1
0
0
1
1
19(decimal)
1
0
0
5’th Band
1
0
1
0
0
20(decimal)
Data Min: 00 to Max: 7DH
19. Programme Add/Skip(Command: m b)
►► To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
Ack [v][ ][Set ID][ ][OK/NG][Data][x]
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
20. Key(Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - See p. 23.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
21. Control Back Light(Command: m g)
►► To control the back light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
18. Tune Command (Command: m a)
16. Auto Configure(Command: j u)
(Only RGB support model)
0
29
30 EXTERNAL CONTROL DEVICE SETUP
22. Input select (Command: x b)
ENG
ENGLISH
(Main Picture Input)
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
LSB
0
0
0
0
0
0
External Input
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping
00 :
Step 0
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E : Step 110
73 :
74 :
Step 115
Step 116
CF : Step 199
FE : Step 254
FF : Step 255
0
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring any
service.
MODEL
SERIAL
(Only DTV)
Download PDF